All about the
Use & Care
of your Laundry Center
TABLE OF CONTENTS
Important Safety Instructions..............................2-5
Washer Operating Instructions ..........................6-13
Dryer Operating Instructions...........................14-17
Care and Cleaning..........................................18-19
Avoid Service.................................................20-21
Warranty ............................................................22
Español ..............................................................23
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
240 v Electric Dryer
120 v Gass Dryer
Groundiing type
wall receptacle
10-30R
3-wire
UL-approveed serrvice
cord mustt be installed
on electric dryers (not
provided wwith unit
except those
Do not, under
any circumsstances,
cut, remove,
(fused 30 amp)
or bypass the
grounding prong.
manufactured ffor sale
in Canada).
14-30R
4-wire
(fused 30 amp)
Power cord with
3-prong grounded plug
Avoid fire hazard or electrical shock. Do not use an adaptor plug or extension cord or remove grounding
prong from electrical power cord. Failure to follow this warning can cause serious injury, fire or death.
WARNING - RISK OF FIRE
To reduce the risk of fire, electrical shock, or injury to persons when using this laundry center, comply with the basic
warnings listed below. Failure to comply with these warnings could result in serious personal injuries.
You can be killed or seriously injured if you don’t follow these Important Safety Instructions:
PREVENT FIRE
WARNING
• Do not wash or dry items that have been previously
cleaned in, soaked in, or spotted with gasoline, clean-
FIRE HAZARD
ing solvents, kerosene, cooking oils, waxes, etc. Do not
store these items on or near the washer. These sub-
stances give off vapors or chemical reactions that could
ignite or explode.
• Do not put oily or greasy rags or clothing on top of the
laundry center. These substances give off vapors that
could ignite the materials.
• Do not add gasoline, cleaning solvents, or other flam-
mable or explosive substances to the wash water. These
substances give off vapors that could ignite or explode.
• Under certain conditions, hydrogen gas may be pro-
duced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used for such a
period, before using the washer, turn on all hot water
faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen
gas. Hydrogen gas is flammable; do not smoke or use
an open flame during this time.
A clothes dryer produces combustible lint. The dryer
must be connected to an outdoors exhaust. Regularly
inspect the outdoor exhaust opening and remove any
accumulation of lint around the opening and in the
surrounding area.
• Clean the lint screen before or after each load. The in-
terior of the dryer, lint screen housing and exhaust duct
should be cleaned approximately every 18 months by
qualified service personnel. An excessive amount of lint
build-up in these areas could result in inefficient drying
and possible fire. See Care and Cleaning.
• Do not operate the dryer if the lint screen is blocked,
damaged or missing. Fire hazard, overheating and
damage to fabrics can occur.
• Do not obstruct the flow of ventilating air. Do not stack
or place laundry or throw rugs against the front or back
of the dryer.
• Do not spray any type of aerosol into, on or near dryer
at any time.
• Do not store or use gasoline or other flammable vapors
or liquids in the vicinity of this or any other appliance.
• Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
• Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of the
fabric softener or product.
• Do not dry articles containing rubber, plastic or similar ma-
terials such as bras, galoshes, bath mats, rugs, bibs, baby
pants, plastic bags and pillows that may melt or burn.
Some rubber materials, when heated, can under certain
circumstances produce fire by spontaneous combustion.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
• Do not continue to use the laundry center if you hear
squeaking, grinding, rubbing or other unusual noises.
This could be a sign of mechanical breakdown and lead
to fire or serious injury. Contact a qualified technician
WARNING
FIRE/ELECTRICAL SHOCK HAZARD
Avoid fire hazard or electrical shock. Do not use an
adaptor plug or extension cord or remove grounding
prong from electrical power cord. Failure to follow this
warning can cause serious injury, fire or death.
immediately.
• Failure to comply with these warnings could result in
fire, explosion, serious bodily injury and/or damage to
the rubber or plastic parts of the laundry center.
PROTECT CHILDREN
• Do not allow children to play on or in the laundry cen-
ter. Close supervision of children is necessary when the
washer is used near children. As children grow, teach
them the proper, safe use of all appliances.
• Destroy the carton, plastic bag and other packing mate-
rials after the laundry center is unpacked. Children might
use them for play. Cartons covered with rugs, bed-
spreads or plastic sheets can become airtight chambers.
Groundingg type
wall receptacle
Do not, under
any circumsttances,
cut, remove,
or bypass the
groundinng prong.
• Keep laundry products out of children’s reach. To pre-
vent personal injury, observe all warnings on product
labels.
• Before the laundry center is removed from service or
discarded, remove the washer door to prevent acciden-
tal entrapment.
Power cord with
3-prong grounded plug
• Failure to comply with these warnings could result in
serious personal injuries.
PREVENT INJURY
• ALWAYS disconnect the laundry center from the electrical
supply before attempting any service or cleaning. Failure
to do so can result in electrical shock or injury.
• Do not use any type spray cleanser when cleaning dryer
interior. Hazardous fumes or electrical shock could occur.
• To prevent injury, do not reach into the laundry center
while parts are moving. Before loading, unloading or
adding items, push in the cycle selector knob to stop
the cycle. Allow the wash tub or dryer drum to coast to
a complete stop before reaching inside.
• To prevent shock hazard and assure stability during
operation, the laundry center must be installed and
electrically grounded by a qualified service person in
accordance with local codes. Installation instructions
are packed in the washer for installer’s reference. Refer
to INSTALLATION INSTRUCTIONS for detailed
grounding procedures. If the laundry center is moved
to a new location, have it checked and reinstalled by a
qualified service person.
• To prevent personal injury or damage to the laundry
center, the electrical power cord of a gas dryer must be
plugged into a properly grounded and polarized 3-prong
outlet. The third grounding prong must never be removed.
Never ground the dryer to a gas pipe. Do not use an ex-
tension cord or an adaptor plug.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
• Follow package directions when using laundry products.
PREVENT INJURY AND DAMAGE TO THE APPLIANCE
Incorrect usage can produce poisonous gas - resulting
in serious injury or death.
• Do not combine laundry products for use in 1 load un-
less specified on the label.
• Do not mix chlorine bleach with ammonia or acids such
as vinegar.
To prevent serious personal injury and damage to the
laundry center:
• All repairs and servicing must be performed by an au-
thorized servicer unless specifically recommended in this
Use & Care Guide. Use only authorized factory parts.
• Do not tamper with controls.
• Do not install or store the laundry center where it will
be exposed to the weather.
• Do not install on carpet. Install laundry center on a
solid floor. It may be necessary to reinforce the floor to
prevent vibration or movement.
• Do not sit on, step on or stand on the laundry center.
Do not rest heavy loads on top. The laundry center is
not meant to support weight.
• To reduce the risk of electric shock, disconnect this
appliance from the power supply before attempting
any user maintenance. Canceling a cycle or turning the
power off at the console does not disconnect this appli-
ance from the power supply.
WARNING
HARMFUL VAPOR HAZARD
Do not use or mix liquid chlorine bleach with other
household chemicals such as toilet cleaners, rust
removers, acid or products containing ammonia. These
mixtures can produce dangerous fumes which can
cause serious injury or death.
• This laundry center is equipped with an electrical over-
load protector. The washer motor will stop if it becomes
overheated.
• A thermal limiter switch automatically turns off the
dryer motor in the unlikely event of an overheated
situation. A service technician must replace the thermal
limiter switch after correcting the fault.
• Failure to comply with these warnings could result in
serious personal injuries.
CAUTION
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of
substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to
warn customer of potential exposure to such substances. Included in this list are soot and carbon monoxide, both of
which may be produced by the use of this product.
ÍNOTE
The instructions appearing in this Use and Care Guide are not meant to cover every possible condition and situa-
tion that may occur. Common sense and caution must be practiced when installing, operating and maintaining any
appliance.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
Washing Procedures
• Place delicate and small items such as bras,
hosiery and baby socks in a
mesh bag.
WARNING
To reduce the risk of fire, electric shock or injury to
persons, read these IMPORTANT SAFETY INSTRUCTIONS
in this Use and Care Guide before operating your washer.
1 Sort laundry i
can be washe
(Mesh bag not included.)
3 Pretreat stains and heavy soil.
• See Stain Removal Guide
in this guide for
T
U
safe, successful
stain removal
instructions.
• Sort items
by recom-
mended cy-
cle and water
temperature.
4 Add a measured amount of detergent to the
wash tub before adding the laundry load.
• Separate white, light and colorfast items from dark
and non-colorfast items.
• Separate items that shed lint from items that
attract lint. Casual, synthetic, knit, and cordu-
roy items will pick up lint from towels, rugs, and
bedspreads.
For best results
Use a low-sudsing, high efficiency deter-
gent to prevent oversudsing. Look for this
symbol on the detergent label:
• Separate heavily soiled items from lightly soiled items.
• Separate lacy, sheer, loosely knit, or delicate items
from durable items.
• Do not machine wash items containing fiberglass.
Small particles of fiberglass left in the drum may
transfer to fabrics in other loads and cause skin
irritation and/or damage to fabrics.
• Follow detergent manufacturer’s directions. The
amount required depends on type of detergent,
load size and soil level, and water hardness.
5
If desired, add liquid bleach to bleach dispenser.
• Before adding the wash load, add liquid bleach to
bleach dispenser located in left front corner under
the lid:
2 Prepare items for washing.
• Empty pockets.
• Brush off lint and dirt. Shake out rugs and beach
towels.
• Close zippers, fasten hooks, button buttons, tie
strings and sashes, and remove non-washable
trims and ornaments.
• Mend rips and tears to prevent further damage
during washing.
• Refer to bleach manufacturer’s directions for quan-
tity to add.
• Then add 1 cup (240 ml) water to flush the dis-
penser.
• Do not use powdered bleach in the bleach dispens-
er. Add powdered bleach to the empty tub.
• Turn knit items inside out to prevent pilling.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
Washing Procedures, continued
For models without a built-in fabric softener
dispenser:
• Follow fabric softener label directions.
• Add diluted fabric softener to the final rinse. You
may use a fabric softener dispensing ball.
6 Add laundry load to washer.
• For best washing performance, dry load level
should not be higher than the upper row of holes in
the wash tub. Do not overload the washer.
ÍNOTE
To prevent staining, do not overfill the “FABRIC
SOFTENER” chamber or pour liquid fabric softener
directly on the wash load.
Other Wash Products
• Water conditioner, detergent booster and enzyme
products may be added with the detergent.
IMPORTANT
• Combine large and small items in a load. Load
large items first. Large items should not be more
than half the total wash load.
• When washing a single heavy item, add 1 or 2
towels to balance the load.
Use of multi-product (detergent plus softener) sheets
or color-absorbing sheets NOT recommended. They
could disable your machine and result in unwarranted
repair costs.
7 If desired, add liquid fabric softener to fabric
softener dispenser (available on some models).
8 Select the appropriate cycle and settings for
the load.
For models with built-in dispenser:
• See Washer Operating Instructions on following
pages.
9 Start the washer.
• Close the washer lid. The washer will not operate
with the lid open.
• Push in or turn the cycle selector knob or turn any
option knob to “wake” the washer. You will hear
three beeps to indicate washer is ready to operate.
• After making your selections, push in the selector
knob to start the cycle. You will hear one beep and
the washer lid will lock.
• Unless a manual water level is selected (if avail-
able), the washer will perform a dry load sensing
procedure before adding water to the tub.
• To add a forgotten item to the wash tub, push in
the cycle selector knob to pause the cycle. You will
hear two beeps. After the lock releases, lift the lid
and add the item. Close the lid and push in the
selector knob again, continuing the current cycle.
• To stop a running cycle, push in the cycle selector
knob.
• Add liquid softener to the dispenser, following fab-
ric softener label directions. DO NOT use granular
detergent in this dispenser.
• DO NOT fill above the maximum fill line.
• Turn fabric softener option on.
• Do not use bleach in this dispenser.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
Washing Procedures, continued
• Place washed items in automatic dryer, line dry, or
10 Remove items when the cycle is completed.
• For your safety, the lid is locked during the operation
of the washer. It will unlock at the cycle end after the
tub has come to a complete stop.
dry flat as directed by fabric care label. Excess wrin-
kling, color transfer or odors may develop in items
left in the washer after the cycle has ended.
For best results
Follow the fabric care label instructions
on items to be washed.
SAFETY LID LOCK
• To open the lid during cycle operation, push in the
cycle selector knob to pause the cycle. You will hear
two beeps. Wait for the lid lock to release. Do not
force open the locked lid.
CAUTION
To avoid serious personal injury, do not operate washer
if safety lid lock is missing, damaged or operating
improperly.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
This manual covers many models and not all cycles, options, or features listed are available on every model. Consoles shown above
for reference only. Your model may differ.
Washing Cycle Selection
normal/heavy (on select models only)
Use this cycle for heavily soiled cottons, towels, shirts,
denims and mixed loads.
Turn the cycle selector in either direction to the cycle
desired.
For best results
Follow the fabric care label
instructions on items to
be washed.
bedding
This cycle is designed for large items such as blankets,
sheets, mattress pads, duvet covers and similar items.
quick wash (on select models only)
Quickly wash a small, lightly soiled load in 25 minutes.
To change the cycle after it has begun, push in or turn the
cycle selector knob to pause the current running cycle.
Make the new selection and push in the cycle selector
knob again to start the new cycle.
rinse & spin
Select rinse & spin for loads that need a cold water
rinse or to add fabric softener that may have been
omitted in a regular cycle.
normal
presoak
Use this load for light to normally soiled cottons,
towels, shirts, denims and mixed loads. For best
combination of energy and water saving and washing
performance, perform this cycle with energy saver
option (if available) selected.
Use this cycle to soak heavily soiled and stained items
before washing. Any temperature may be selected,
but cold water is recommended with this cycle as
warmer water may set some stains. Use the amount
of detergent recommended for a normal wash cycle. If
desired, use a bleach or a soaking agent safe for the
fabric. The washer will drain at the end of the cycle.
comforter (on select models only)
Add one large comforter or two light-duty sleeping
bags to the comforter cycle. Press the item(s) to the
bottom of the tub as much as possible to prevent them
from floating as the tub fills with water.
ÍNOTE
heavy duty
Follow Presoak with a complete wash cycle suitable
Use this cycle for heavily soiled, durable garments - ex.
towels, sports gear, or fabric tote bags. For best soil
and stain removal, use the hottest water safe for the
fabrics being washed.
for the load using a half dose of detergent.
casual
Use this cycle for poly blends with a permanent press
or no-iron finish.
delicates
Use this cycle for lightly soiled knits and delicates which
require gentle washing.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
Washing Cycle Settings
cold water clean (on select models)
Wash and rinse temperatures are equivalent to
temperature of cold tap supply. Use this selection for
fabrics and colors that are prone to dye transfer. For
Wash Water Temperature
Turn the temp knob until the desired wash water
temperature is selected. Select a wash water temperature
according to fiber content, colorfastness and soil level. To
protect your fabrics, the temperature range of cold to hot
settings may be different depending on cycle selected.
use with cold water
detergents.
Water Level (on select models, automatic on others)
Turn the water level knob (on select models) to select a
water level appropriate for the load size. For best results,
DO NOT overload. Add items loosely to the tub. The dry
load should not be higher than the top row of holes in the
wash tub. There should be enough water in the tub for
items to move freely.
For best results
Follow the fabric care label instructions
on items to be washed.
The water heater setting and its distance from the
washer, water usage in other parts of the home, and
seasonally low ground water temperature in some
geographic areas can affect water temperature.
ÍNOTE
If auto water level is selected, the washer will perform
a dry load sensing procedure before adding water to
the tub. Water level is automatically calculated by the
washer on models without a water level knob.
hot
Use this setting for heavily soiled white or colorfast
cottons and blends.
warm
Use this setting for normally soiled white or colorfast
cottons or blends.
Fabric Softener (on select models)
If your model is equipped with an automatic fabric
softener dispenser, you must turn the fabric softener
switch to the “on” position for correct operation. See
Care and Cleaning for dispenser cleaning procedures.
cool (on select models)
Use this setting for normally soiled sheets, casual items
and washable woolens.
cold
Some warm water will automatically blend with cold tap
supply to achieve cold. Use this setting for lightly soiled
non-colorfast items, knits, delicates, and hand washables.
Energy Saver (on select models)
The energy saver option reduces water temperature to
save energy, lowers water usage slightly and also extracts
more water to reduce drying time.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
Safe Stain Removal Procedures
To reduce the risk of fire or serious injury to persons or
property, comply with the basic warnings listed below:
WARNING
HARMFUL VAPOR HAZARD
Do not use or mix liquid chlorine bleach with other
household chemicals such as toilet cleaners, rust
removers, acid or products containing ammonia. These
mixtures can produce dangerous fumes which can
cause serious injury or death.
• Read and comply with all instructions on stain re-
moval products.
• Keep stain removal products in their original labeled
containers and out of children’s reach.
• Thoroughly wash any utensils used.
• Do not combine stain removal products, especially
ammonia and chlorine bleach. Dangerous fumes can
result.
• Never wash items which have been previously
cleaned in, washed in, soaked in or spotted with
gasoline, dry cleaning solvents or other flammable
or explosive substances because they give off vapors
that could ignite or explode.
• Never use highly flammable solvents, such as gaso-
line, inside the home. Vapors can explode on contact
with flames or sparks.
For Successful Stain Removal:
• Remove stains promptly.
For best results
Follow the fabric care label instructions
on items to be washed.
• Determine the kind of stain, then follow the recom-
mended treatment in the stain removal chart on the
next page.
• To pretreat stains, use a prewash product, liquid
detergent, or a paste made from powder detergent
and water.
• Use cold water on unknown stains as hot water can
set stains.
• Consult care label instructions for treatments to avoid
on specific fabrics.
• Check for colorfastness by testing stain remover prod-
ucts on an inside seam.
• Rinse and wash items after stain removal.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
Stain Removal Suggestions
STAIN
TREATMENT
Adhesive tape, chewing
gum, rubber cement
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with pre-
wash stain remover or nonflammable dry cleaning fluid.
Baby formula, dairy
products, egg
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more.
Wash.
Beverages (coffee, tea,
soda, juice, alcoholic
beverages)
Pretreat stain. Wash using cold water and bleach safe for fabric.
Blood
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing
enzymes. Wash using bleach safe for fabric.
Candle wax, crayon
Scrape off surface wax. Place stain face down between paper towels. Press with warm
iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with
prewash stain remover or nonflammable dry cleaning fluid. Hand wash to remove sol-
vent. Wash using bleach safe for fabric.
Chocolate
Pretreat or soak in warm water using product containing enzymes. Wash using bleach
safe for fabric.
Collar or cuff soil, cos-
metics
Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white
fabric
Use packaged color remover. Wash using bleach safe for fabric.
Grass
Pretreat or soak in warm water using product containing enzymes. Wash using bleach
safe for fabric.
Grease, oil, tar (but-
ter, fats, salad dressing,
cooking oils, car grease,
motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy
stains and tar, apply nonflammable dry cleaning fluid to back of stain. Replace towels
under stain frequently. Rinse thoroughly. Wash using hottest water safe for fabric.
Ink
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain
remover, denatured alcohol or nonflammable dry cleaning fluid.
Mildew, scorch
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water
before washing. Badly mildewed fabrics may be permanently damaged.
Mud
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Mustard, tomato
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail pol-
ish remover to back of stain. Repeat, replacing paper towels frequently. Do not use on
acetate fabrics.
Paint, varnish
Perspiration
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it
cannot be removed. OIL BASED AND VARNISH: Use solvent recommended on can label.
Rinse thoroughly before washing.
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach
in hottest water safe for fabric.
Rust, brown or yellow
discoloration
Use rust remover safe for fabric. Do not use chlorine bleach because it may intensify
discoloration.
Shoe polish
LIQUID: Pretreat with a paste of powder detergent and water. PASTE: Scrape residue
from fabric. Pretreat with prewash stain remover or nonflammable dry cleaning fluid.
Rinse. Rub detergent into dampened area. Wash using bleach safe for fabric.
Tomato
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Urine, vomit, mucus,
feces
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
Wine
Pretreat or soak in cold water. Wash in hottest water and bleach safe for fabric
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHER OPERATING INSTRUCTIONS
Common Washing Problems
Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing
results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
PREVENTIVE MEASURES
Blue stains
• Undiluted liquid detergent
or fabric softener dispensed
directly onto fabric.
• If caused by detergent, mix 1 cup (240
ml) white vinegar with 1 quart (.95 L)
• Add detergent to empty tub. Do not
pour on dry load.
water in a plastic container. Soak item 1 • Avoid overfilling fabric softener
hour. Rinse.
• If caused by fabric softener, rub stains
with bar soap. Wash.
compartment of dispenser.
Discoloration,
graying
• Not enough detergent.
• Wash water temperature too
low.
• Rewash with correct amount of deter-
gent and hottest water safe for fabric.
• Add bleach safe for fabric.
• Sort items by soil level and color.
• Use correct amount of detergent,
hottest water and bleach safe for
fabric.
• Incorrect sorting.
Greasy, oily
stains
• Not enough detergent.
• Treat with prewash stain remover or
liquid detergent.
• Use correct amount of detergent
and hottest water safe for fabric.
• Do not pour liquid fabric softener
directly on fabric. See Operating
Your, step 5.
• Undiluted liquid fabric soft-
ener poured directly on fabric. • Increase detergent and water tempera-
ture. Rewash.
• Rub fabric softener stains with bar soap.
Holes, tears, or
snags
• Incorrect use of chlorine
bleach.
• May be irreversible if rips, tears and
seams cannot be mended.
• Never pour chlorine bleach directly
on fabric.
• Check condition of items before
washing. See Operating Your, steps
2 and 5.
• Unfastened zippers, hooks,
buckles.
• Rips, tears and broken threads.
• Overloading the washer.
• Degradation of fabric.
Lint
• Incorrect sorting.
• Reduce load size. Rewash using correct
water temperature, water level, and
amount of detergent.
• See Washing Procedures, steps 1
and 2.
• Tissues left in pocket.
• Overloading the washer.
• Not enough detergent.
• Undissolved detergent has left
a residue resembling lint.
• Static cling is attracting lint.
• Load washed too long.
• Do not overload washer.
• Add nonprecipitating water conditioner to • Use correct temperature and
wash water to remove detergent residue.
• Add liquid fabric softener to final rinse.
• Dry load in dryer.
amount of detergent, water and
wash time.
• Remove lint with lint brush or roller.
Pilling
• Pilling is normal with synthetic • Use a lint brush or shaver to remove
• Use fabric softener in the washer to
lubricate fibers.
• When ironing, use spray starch or
fabric finish on collars and cuffs.
• Turn items inside out to reduce
abrasion.
(Fibers ball up
and cling to
fabric.)
and permanent press fabrics.
This is due to abrasion from
normal wear.
pills.
Residue or
powder on dark
items;
Stiff, harsh
fabrics.
• Undissolved detergent.
• Some granular detergents
can combine with hard water
minerals to form a residue.
• Overloading the washer.
• Rewash load.
• Increase water temperature using
hottest water safe for fabric.
• Do not overload washer.
• Use liquid detergent or use non-
precipitating water conditioner with
powder detergent.
Wrinkling
• Overloading the washer.
• Reduce load size.
• Do not overload washer.
• Remove items from washer as soon
as cycle is completed.
• Incorrect wash cycle for wash • Rinse in cold water with liquid fabric
load.
softener using the casual or delicate
cycle.
• Use liquid fabric softener.
Yellow buildup
of body soil on
synthetic fabrics
• Agitation time too short.
• Wash water temperature too
low.
• Soak in detergent booster or product
containing enzymes.
• Select correct wash cycle.
• Use correct amount of detergent.
• Wash in hottest water safe for fabric us- • Wash synthetics frequently using
• Not enough detergent.
ing casual cycle.
hot or warm water.
• Increase detergent.
• Add bleach safe for fabric or treat with
color remover.
Yellow or brown
rust stains
• Iron or manganese in water
supply, water pipes, or water
heater.
• To restore discolored load of whites, use • Use nonprecipitating water softener.
rust remover safe for fabric.
• Do not use chlorine bleach to remove
rust stains. It may intensify discolor-
ation.
• Before washing, run hot water for a
few minutes to clear lines.
• Drain water heater occasionally.
• For an ongoing problem, install
an iron filter in your water supply
system.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER OPERATING INSTRUCTIONS
Drying Procedures
• If desired, place a dryer fabric softener sheet on
top of the load at the beginning of the cycle.
• To save energy and time and avoid uneven drying
and wrinkling, do not overload the dryer.
• When drying large items, dry only two or three
items at a time. Fill out the load with small and
medium sized items.
WARNING
To reduce the risk of fire, electric shock or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS
in this Use and Care Guide before operating your dryer.
• For delicate or very small loads, add two or three
similar items to improve tumbling action.
1 Prepare load for drying.
• Dry items of similar fabric, weight and construction
in the same load.
• Separate dark items from light-colored items. Sepa-
rate items that shed lint from those that attract lint.
ÍNOTE
• Check for stains which may not have been removed
in washing. Repeat stain removal process and wash
again before drying. Dryer heat may permanently
set some stains.
Over-drying can cause wrinkles, shrinkage, lint,
harshness and a build up of static electricity.
4 Select the appropriate cycle and settings for
each load.
• Place delicate or small
items in a mesh bag.
• See Dryer Operating Instructions on following
pages.
• Be sure buckles,
buttons and trim are
5 Start the dryer.
heatproof and won’t
• Close the dryer door. The dryer will not operate with
the door open.
damage the drum
finish. Close zip-
• Push in or turn the cycle selector knob or turn any
option knob to “wake” the dryer. You will hear three
beeps to indicate dryer is ready to operate.
• After making your selections, push in the selector
knob to start the cycle. You will hear one beep before
the drum begins to rotate.
• To add or remove items when the dryer is running,
push in the cycle selector knob to pause the cycle
and open the door. Opening the door with a cycle
running will also pause the cycle. You will hear two
beeps. Allow the drum to come to a complete stop
before reaching inside. Add or remove the item,
close the door and push in the selector knob again,
continuing the current cycle.
pers, button buttons,
(Mesh bag not included.)
fasten hooks and
Velcro®-like fasteners. Tie strings and sashes to
prevent snagging and tangling.
2 Check that the
lint filter is clean
and in place.
• To stop a running cycle, push in the cycle selector
knob.
ÍNOTE
If drying a single large or bulky item, such as a
comforter, remove the item part way through the cycle
and turn it “inside out” to maximize drying effectiveness.
Place item back in dryer and re-start cycle.
CAUTION
6 When the cycle ends, remove items immedi-
ately and hang or fold.
Do not operate dryer without lint filter in place.
3 Load the dryer and close the door.
• Load items loosely. The average wet load will
fill the drum 1/3 to 1/2 full. Items need room to
tumble freely for even drying and less wrinkling.
IMPORTANT
Clean the lint filter after every load.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER OPERATING INSTRUCTIONS
This manual covers many models and not all cycles, options, or features listed are available on every model. Consoles shown above
for reference only. Your model may differ.
Drying Cycle Selection
Drying time varies depending on size and dampness of
load and fabric type. If the load is too small or almost
dry, the moisture sensing bars may not detect enough
moisture to continue the cycle and the cycle may end
after a few minutes. If this occurs, select a Timed Dry
cycle.
Turn the cycle selector in either direction to the cycle
desired.
For best results
Follow the fabric care
label instructions on
items to be dried.
Room temperature and humidity, type of installation and
electrical voltage or gas pressure can also affect drying
time.
To change the cycle after it has begun, push in or turn
the cycle selector knob to pause the current running
cycle. Make the new selection and push in the cycle se-
lector knob again to start the new cycle.
normal
Select this cycle to dry everyday fabrics including
cottons, linens and sheets.
heavy duty
Select this Auto Dry cycle to dry durable fabrics such as
work wear and overalls.
Auto Dry Cycles
Auto Dry cycles take the guesswork out of selecting
the correct drying time for each load. Moisture sensing
bars in the front of the dryer drum (on certain models)
sense the moisture level of the load as it tumbles
through the heated air. With Auto Dry cycles, the load
will automatically be dried at the selected temperature
to a specific dryness level. Auto Dry cycles save time and
energy and protect fabrics.
delicates
Select this cycle to dry knits and delicates.
casual
Select this cycle to dry cottons, blends and permanent
press items with a no-iron finish.
cotton towels (on select models)
Select this cycle to dry heavy loads such as towels and
non-rubber-backed bath mats.
When the load has reached the dryness level, it will
continue to tumble during a cool down period. This helps
reduce wrinkling and makes items easier to handle during
unloading.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER OPERATING INSTRUCTIONS
Drying Cycle Selection, continued
Drying Cycle Settings
Drying Temperature
Timed Dry Cycles
Select the temperature setting most suitable for each
load. To protect your fabrics, not all temperatures are
available with every cycle. If an unavailable temperature
setting is selected by the user, the nearest available
temperature will be substituted.
WARNING
FIRE HAZARD
To avoid fire hazard, do not use heat to dry items
containing feathers or down, foam rubber, plastics
similarly textured, rubber-like materials. Use a Timed
Dry cycle and the air dry setting.
The air dry (on select models) setting can be used only
in a timed cycle. Air dry setting tumbles the load without
heat. Use air dry to freshen clothing, pillows or blankets,
or to dust draperies.
quick dry (on select models only)
Select this timed cycle to quickly dry a small load made
up of just a few items. It provides approximately 20
minutes of tumbling followed by a cool down period.
Chime (on select models)
A signal will sound at the end of the cycle if selected.
refresh (on select models only)
Select refresh to help remove wrinkles from clean and
dry items that were not taken from the dryer at the
end of the cycle, have been stored in crowded closets
or drawers, or unpacked from luggage following a
trip. It provides approximately 10 minutes of tumbling
followed by a 5-minute cool down period.
timed dry
To manually select the drying time for any load, turn
the knob to a numbered setting: 15 (on select models),
30, 60, or 90 minutes. Moisture sensing bars (if
equipped) are not active and dryer will continue to heat
throughout the cycle until the final cool down period.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER OPERATING INSTRUCTIONS
Other Features
Drying Rack (some models)
1. Open the dryer door and remove the lint screen.
2. Insert drying rack into the dryer drum. Place the front
bar under the lip of the lint screen opening.
Use the drying rack to dry items which should not be
tumble dried. If your model did not come with a drying
rack, you may order one.
3. Place items to be dried on top of the rack. Weight
should not exceed 10 lbs. Leave space between items,
but do not let items hang over the sides or through
the grids. Do not tumble other items when using the
drying rack.
4. Select a timed cycle. If items to be dried contain
plastic, foam rubber, rubber-like materials, feathers or
down, then only use the air dry temperature setting.
5. When items are dry, remove the rack and replace
the lint screen. If lint screen is not in place, tumbling
items could enter the exhaust system and cause
damage to the dryer.
Place the front bar
under the lip of the lint
screen opening.
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric
damage. For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
PREVENTIVE MEASURES
Greasy, oily
stains
• Fabric softener sheet.
• Rub fabric softener stains with
bar soap. Rinse and rewash.
• Add a few bath towels to small loads
for proper tumbling.
• Some “silk-like” fabrics should be air
dried.
• Use proper drying temperature.
• Place fabric softener sheet on top of
load before starting the dryer.
Lint
• Overloading.
• Overdrying causes static
electricity.
• Reduce load size and rewash
using liquid fabric softener in the • Use fabric softener in washer or dryer
final rinse.
• Do not overload dryer.
to reduce static electricity.
• Lint screen not clean when
cycle began.
• Lint is attached to “pills.”
• Or, add a fabric softener sheet
and tumble without heat.
• Use lint brush or roller to remove • Check that lint filter is clean and in
• Remove items when they are slightly
damp to avoid overdrying.
lint.
place.
Pilling
• Overdrying.
• Use a lint brush or shaver to
remove pills.
• Use fabric softener to lubricate fibers.
• When ironing, use spray starch or
fabric finish on collars and cuffs.
• Turn items inside out to reduce abra-
sion.
(Fibers break
off, ball up and
cling to fabric.)
Shrinking
Wrinkling
• Temperature too high.
• Overdrying.
• Irreversible condition.
• Follow fabric care label directions.
• If shrinking is a concern, check load
often.
• Remove items while slightly damp and
hang or lay flat to complete drying.
• Block knits into shape.
• Overloading.
• Leaving items in dryer after
cycle ends.
• Reduce load size and tumble at
medium or low heat for 5-10
minutes.
• Do not overload dryer.
• Remove items as soon as cycle ends.
• Remove items immediately. Hang
or fold.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
WARNING
WARNING
FIRE HAZARD
To reduce risk of fire or serious injury to persons or property,
comply with the basic warnings listed in the Important Safety
Instructions and those listed below.
A clothes dryer produces combustible lint.
The dryer must be connected to an outdoors
exhaust. Regularly inspect the outdoor exhaust
opening and remove any accumulation of lint
around the opening and in the surrounding area.
• Before cleaning the laundry center interior, unplug the electrical
power cord to avoid electrical shock hazards.
• Do not use any type spray cleanser when cleaning the dryer
interior. Hazardous fumes or electrical shock could occur.
INSIDE DRYER
• Clean the lint filter after every load. Lint build-up on the filter
restricts air flow, which causes longer drying times. The filter is
located at the bottom of the door opening. Remove by pulling
straight up. Remove the lint and replace the filter.
• Occasionally a waxy build-up may form on the lint filter and/or
moisture sensing bars from using dryer-added fabric softener
sheets. To remove this build-up, wash them with warm, soapy
water. Dry the filter thoroughly and replace. Do not operate the
dryer without the lint filter in place.
• If the dryer drum becomes stained from noncolorfast fabrics,
clean the drum with a damp cloth and a mild liquid household
cleanser. Remove cleanser residue before drying the next load.
• Every 18 months an authorized servicer should clean the dryer
cabinet interior and exhaust duct. These areas can collect lint
and dust over time. An excessive amount of lint build-up could
result in inefficient drying and possible fire hazard.
IMPORTANT
Clean the lint filter after every load.
INSIDE WASHER
• Remove items from the washer as soon as the cycle ends.
Excess wrinkling, color transfer, and odors may develop in items
left in the washer.
• Dry the washer top, the area around the lid opening, and the
underside of the lid. These areas should always be dry before the
lid is closed.
• Before cleaning the washer interior, unplug the electrical power
cord to avoid electrical shock hazards.
• When extremely soiled items have been washed, a dirty residue
may remain on the tub. Remove this by wiping the tub with a
nonabrasive household cleanser. Rinse thoroughly with water.
ÍNOTE
Fabric softener may build up in the dispenser
well. Residue should be removed once or twice
a month.
• The base plate or tub may become stained from fabric dye.
Clean these parts with a nonabrasive household cleanser. This
prevents dye transfer to future loads.
FABRIC SOFTENER DISPENSER
a
• Remove the dual chamber insert (a) from the bleach and fabric
softener dispenser by pinching at the chamber divider and lifting
upward. Also remove the siphon cap (b).
• Rinse the insert and cap with a combination of ¾ cup liq-
uid chlorine bleach and 1 gallon hot tap water to remove any
buildup. Large amounts of fabric softener residue may indicate
improper dilution or more frequent cleaning is required. Rinse
well with tap water.
b
• For the dispenser well, use a small brush to clean the recesses.
Remove all residue.
• Replace the siphon cap and insert by pressing it in place until
you hear a slight click.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
Cleaning Instructions, continued
OUTSIDE
• When washing is completed, wipe top and sides of laundry
center with a damp cloth. Turn water faucets off to prevent
pressure build-up in the hoses.
• Clean the cabinet with mild soap and water. Never use
harsh, gritty or abrasive cleansers
• If the cabinet becomes stained, clean with diluted chlorine
bleach (1 part bleach to 8 parts water). Rinse several times
with clear water.
• Remove glue residue from tape or labels with a mixture of
warm water and mild detergent. Or, touch residue with the
sticky side of tape.
• Before moving the laundry center, place a strip of card-
board or thin fiberboard under the front leveling legs to
prevent damage to the floor.
IMPORTANT
Do not store or place laundry products on top of
laundry center at any time. They can damage the
finish or controls.
Winterizing Instructions
IMPORTANT
If the laundry center is stored in an area where freezing
can occur or moved in freezing temperatures, follow these
winterizing instructions to prevent damage to the washer:
Follow WINTERIZING
INSTRUCTIONS for
1 Turn off water supply faucets.
cold weather storage
and care.
2 Disconnect hoses from water supply and drain water from
hoses.
3 Plug electrical cord into a properly grounded electrical
outlet.
4 Add 1 gallon (3.8 L) nontoxic recreational vehicle (RV)
antifreeze to empty wash drum. Close door.
5 Select the rinse & spin cycle. Start the cycle and let the
washer drain for 1 minute to drain out all the water. Not all
of the RV antifreeze will be expelled.
6 Stop the cycle, unplug electrical power cord, dry off tub
interior and close the lid.
7 Store laundry center in an upright position.
8 To remove antifreeze from washer after storage, run
empty washer through a complete cycle using detergent.
Do not add wash load.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
AVOID SERVICE CHECKLIST
Before calling for service, review this list. It may save both time and expense. The list includes common occurrences
that are not the result of defective workmanship or materials in this laundry center.
OCCURRENCE
NOISE
POSSIBLE CAUSE
SOLUTION
Rattling and clanking
noise.
Foreign objects such as coins or safety pins may be
in drum or pump.
Stop washer and check drum. If noise continues after washer is
restarted, objects may be in pump. Call your authorized servicer.
Belt buckles and metal fasteners are hitting wash
drum.
To prevent unnecessary noise and damage to tub, fasten fas-
teners and turn items inside out.
Thumping sound.
Heavy wash loads may produce a thumping sound.
This is usually normal. If sound continues, washer is
probably out of balance.
Stop washer and redistribute wash load.
Squealing sound or hot
rubber odor.
Washer is overloaded.
Do not overload washer. Stop washer and reduce load.
Vibrating noise.
Washer is not resting firmly on floor.
Move washer so it rests firmly on floor. Adjust leveling legs. See
INSTALLATION INSTRUCTIONS for details.
Shipping bolt has not been removed during installation.
Wash load unevenly distributed in tub.
See INSTALLATION INSTRUCTIONS for removing shipping bolt.
Stop washer and rearrange wash load.
OPERATING
Washer does not start.
Washer lid is open.
Close washer lid. The washer will not operate when the lid is open.
Electrical power cord may not be plugged in or con- Make sure plug fits tightly in wall outlet.
nection may be loose.
House fuse blown, circuit breaker tripped, or a
power outage has occurred.
Reset circuit breaker or replace fuse. Do not increase fuse
capacity. If problem is a circuit overload, have it corrected by
a qualified electrician. If problem is a power outage, call local
electric company.
Water supply faucets are not turned on.
Turn on water supply faucets.
Motor is overheated. Washer motor will stop if it
becomes overheated.
Wait for the motor to cool down before attempting to restart.
Washer won’t spin.
Residue left in drum.
Lid is not completely closed.
Heavily soiled items.
Close washer lid. The washer will not operate when the lid is open.
Wipe drum with a nonabrasive household cleanser, then rinse.
Shake or brush excess dirt and sand from items before washing
Dryer does not start.
Electrical power cord is not securely plugged in or
plug may be loose.
Make sure the plug fits tightly in wall outlet.
House fuse blown or circuit breaker tripped.
Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded.
Call authorized service person for replacement.
Thermal limiter tripped.
Dryer runs but won’t
heat.
There are 2 house fuses in the dryer circuit. If 1 of the Replace fuse.
2 fuses is blown, the drum may turn but the heater will
not operate. (electric models)
Gas supply valve is not open (gas models).
Check to make sure supply valve is open. See INSTALLATION
INSTRUCTIONS for procedure.
Dryer does not have enough air supply to support
the burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has been a util- Refill or replace tank. Dryer should heat when utility service is
ity interruption of natural gas (gas models).
restored.
Drying cycle takes too
long, outside of the dryer
feels too hot or smells
hot.
Lint filter is clogged with lint.
Make sure all lint has been removed from the dryer lint filter
before starting each cycle.
Exhaust duct requirements have not been met.
Exhaust duct must be at least 4 inches in diameter and made of
rigid or semi-rigid metal.
When in place, the duct must have no more than four 90° bends and
must not exceed length listed in INSTALLATION INSTRUCTIONS.
Electric dryer is connected to a 208 volt circuit.
Drying procedures have not been followed.
Drying time will be 20% longer than drying on a 240 volt circuit.
See “Operating Instructions.”
Outside exhaust hood or exhaust duct may be
clogged or restricted.
Clean out any obstruction.
High humidity.
Use a dehumidifier near the dryer.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
AVOID SERVICE CHECKLIST
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
OPERATING, CONTINUED
Excessive wrinkling.
Dryer is overloaded.
Do not overload. See “Operating Instructions.”
Remove items as soon as cycle ends.
See “Operating Instructions.”
Items left in dryer too long.
Insufficient sorting of items.
Drying temperature too high.
Follow fabric care label instructions.
Scratching or chipping of
the drum finish.
Foreign objects such as coins, pins, clips or buttons Always remove foreign objects from pockets before laundering.
are inside the dryer.* Remove objects from drum and restart dryer.
Permanently attached items such as belt buckles, zippers Turn items inside out before drying to prevent scratching and dam-
and fasteners may be hitting the inside of the drum.* age to the dryer.
*Drum damage caused by foreign objects or permanently attached items is not covered by the warranty.
WATER
Wash load too wet after
spin.
Washer is overloaded.
Do not overload washer. See Washing Procedures.
Rearrange load to allow proper spinning.
Straighten drain hose.
Load is out of balance.
Drain hose is kinked.
Water does not enter
washer or it enters slowly.
Washer lid is open.
Close washer lid. The washer will not operate when the lid is open.
Water supply is not adequate in area.
Check another faucet in the house. Wait until water supply and
pressure increase.
Water supply faucets are not completely open.
Water is being used elsewhere in the house.
Fully open hot and cold faucets.
Water pressure must be at least 10 psi (69 kPa). Avoid running
water elsewhere while washer is filling.
Water inlet hoses are kinked.
Straighten hoses.
Water level does not
cover load.
Improper water level selection (for models with
water level/load size control).
Select higher water level/load size.
Washer is overloaded.
Do not overload washer.
Warm or hot water is not
hot enough.
Hot water heater is set too low or is a distance
from washer.
Measure hot water temperature at nearby faucet with candy
or meat thermometer. Water temperature should be at least
120°F (50°C). Adjust water heater as necessary.
Hot water is being used elsewhere in the house.
Avoid using hot water elsewhere before or during washer use.
There may not be enough hot water available for proper clean-
ing. If problem persists, your hot water system may be unable
to support more than 1 use at a time.
Water in washer does not
drain or drains slowly.
Drain hose is kinked or clogged.
Clean and straighten the drain hose.
Water leaks.
Loose fill hose connection at faucet or washer.
House drain pipes are clogged.
Check and tighten hose connections. Install rubber sealing
washers provided.
Unclog drain pipes. Contact plumber if necessary.
Incorrect wash and rinse
temperatures.
Hot and cold water hoses are connected to wrong
supply faucets.
Connect hot water hose to hot water faucet and cold water
hose to cold water faucet.
Water is entering washer
but tub does not fill.
Drain hose standpipe is incorrect height.
Standpipe must be a minimum of 33” (83.82 cm) high to pre-
vent siphoning. See INSTALLATION INSTRUCTIONS.
Water is present in tub after Lid lock malfunction.
wash cycle is complete.
Do not bypass lid lock. Call your authorized servicer.
The drain and spin cycles
did not occur.
Lid lock malfunction.
Do not bypass lid lock. Call your authorized servicer.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAJOR APPLIANCE WARRANTY INFORMATION
For the applicable warranty period as set forth below, as measured from your original date of purchase, Electrolux will repair or
replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and
maintained in accordance with the provided instructions.
Warranty Periods:
• All parts — One year including labor
• Wash tub — Functional life of the product (excluding labor)
• Wash tub drive motor, non-cosmetic defects — Ten years (excluding labor)
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in ordinary
household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not a
part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other
cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges, or mileage
expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine Electrolux
parts or parts obtained from persons other than authorized service companies; or external causes such as abuse, misuse,
inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS
PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND
INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY.
SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE.
IF YOU NEED SERVICE
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be
required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be
obtained by contacting Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North
America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux
authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty
must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are
subject to change without notice.
USA
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
1.800.944.9044
Electrolux Major Appliances
10200 David Taylor Drive
Charlotte, NC 28262
22
Download from Www.Somanuals.com. All Manuals Search And Download.
|