Frigidaire Washer Dryer 134889200 User Manual

OWNERSGUIDE  
TUMBLEACTION  
LAUNDRYCENTER  
MANUALDELUSUARIO  
LAVADORAYSECADORASUPERPUESTAS  
DEACCIÓN GIRATORIA  
P/N134889200(0706)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions (Con't)  
This Owner's Guide provides general  
operating instructions for your laundry  
center. It also contains information about  
features for several other models. Your  
laundrycentermaynothaveeveryfeature  
included. Use the laundry center only as  
instructed in this Owner's Guide.  
Undercertainconditions,hydrogengasmaybeproducedinahotwatersystemthat  
has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot  
water system has not been used for such a period, before using the washer, turn on  
all hot water faucets and let the water flow from each for several minutes. This will  
release any accumulated hydrogen gas. Hydrogen gas is flammable; do not smoke  
or use an open flame during this time.  
To prevent fire, do not use heat to dry items containing plastic, foam rubber or  
similarlytexturedrubber-likematerials,oritemscontainingfeathersordown.UseAir  
Fluff (No Heat) only.  
Avoid fire hazard or  
electricalshock.Donotuseanadaptorplug  
or extension cord or remove grounding  
prongfromelectricalpowercord.Failureto  
followthiswarningcancauseseriousinjury,  
fire or death.  
Clean the dryer lint screen before or after each load. The interior of the dryer, lint  
screen housing and exhaust duct should be cleaned approximately every 18 months  
by qualified service personnel. An excessive amount of lint build-up in these areas  
could result in inefficient drying and possible fire. See Care and Cleaning.  
Do not operate the dryer if the lint screen is blocked, damaged or missing. Fire  
hazard, overheating and damage to fabrics can occur. If your dryer has a drying rack,  
always replace the lint screen when finished using the drying rack.  
Keep area around the exhaust opening and surrounding areas free from the  
accumulation of lint, dust and dirt.  
Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw  
rugs against the front or back of the laundry center.  
Do not spray any type of aerosol into, on or near laundry center at any time.  
Do not use fabric softeners or products to eliminate static unless recommended by  
the manufacturer of the fabric softener or product.  
GAS LAUNDRY CENTERS:  
Grounding  
type  
wall  
receptacle  
Do Not under any  
circumstancescut,  
remove, or bypass  
the groundingprong  
Do not place items exposed to cooking oils in your dryer. Items contaminated with  
cookingoilsmaycontributetoachemicalreactionthatcouldcausealoadtocatchfire.  
Failure to comply with these warnings could result in fire, explosion, serious bodily  
injury and/or damage to the rubber or plastic parts of the laundry center.  
from this plug  
ProtectChildren  
Donotallowchildrentoplayonorinthelaundrycenter.Closesupervisionofchildren  
is necessary when the laundry center is used near children. As children grow, teach  
them the proper, safe use of all appliances.  
Power supplycord with  
3-pronggroundingplug  
CORRECT Use this way ONLY  
Destroythecarton,plasticbagandotherpackingmaterialsafterthelaundrycenter  
isunpacked.Childrenmightusethemforplay.Cartonscoveredwithrugs,bedspreads  
or plastic sheets can become airtight chambers.  
Keep laundry products out of children's reach. To prevent personal injury, observe  
all warnings on product labels.  
Beforethelaundrycenterisremovedfromserviceordiscarded, removethewasher  
lid and dryer door to prevent accidental entrapment.  
FOR YOUR SAFETY  
Do not store or use gasoline or other  
flammable vapors or liquids in the  
vicinity of this or any other appliance.  
Failure to comply with these warnings could result in serious personal injuries.  
Note: The instructions appearing in this  
Owner's Guide are not meant to cover  
every possible condition and situation  
that may occur. Common sense and  
cautionmustbepracticedwheninstalling,  
operatingandmaintaininganyappliance.  
PreventInjury  
To prevent shock hazard and assure stability during operation, the laundry center  
mustbeinstalledandelectricallygroundedbyaqualifiedservicepersoninaccordance  
with local codes. Installation instructions are packed in the laundry center for the  
installer's reference. Refer to INSTALLATION INSTRUCTIONS for detailed grounding  
procedures. If the laundry center is moved to a new location, have it checked and  
reinstalled by a qualified service person.  
Topreventpersonalinjuryordamagetothelaundrycenter,theelectricalpowercord  
of a gas laundry center must be plugged into a properly grounded system. Never  
ground the laundry center to a gas pipe. Do not use an extension cord or an  
adaptor plug.  
Follow package directions when using laundry products. Incorrect usage can  
produce poisonous gas--resulting in serious injury or death.  
Do not use or mix liquid  
chlorine bleach with other household  
chemicals such as toilet cleaners, rust  
removers,acidorproductscontaining  
ammonia.Thesemixturescanproduce  
dangerous fumes which can cause  
serious injury or death.  
-
-
Do not combine laundry products for use in 1 load unless specified on the label.  
Do not mix chlorine bleach with ammonia or acids such as vinegar.  
To prevent serious personal injury and damage to the laundry center:  
-
All repairs and servicing must be performed by an authorized servicer  
unless specifically recommended in this Owner's Guide. Use only authorized  
factoryparts.  
-
-
Do not tamper with controls.  
Donotinstallorstorethelaundrycenterwhereitwillbeexposedtotheweather.  
• ALWAYS disconnect the laundry center from the electrical supply before  
attempting any service or cleaning. Failure to do so can result in electrical shock  
or injury.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions (Con't)  
Do not use any type of spray cleanser when cleaning dryer interior. Hazardous fumes or electrical shock could occur.  
To prevent injury, do not reach into the washer while parts are moving. Before loading, unloading or adding items, push in the  
cycle selector knob and allow the tub to coast to a complete stop before reaching inside.  
To prevent injury, do not reach into the dryer if the drum is moving. Wait until the dryer has stopped completely before reaching  
into the drum.  
Athermallimiterswitchautomaticallyturnsoffthedryermotorintheunlikelyeventofanoverheatedsituation(electricdryersonly).  
A service technician must replace the thermal limiter switch after correcting the fault.  
The washer is equipped with an electrical overload protector. The motor will stop if it becomes overheated. The washer will  
automaticallyrestartafteracooldownperiodofupto30minutes, ifthewasherhasnotbeenmanuallyturnedoffduringthistime.  
Failure to comply with these warnings could result in serious personal injuries.  
Washing Procedures  
Follow the guidelines below for preparing the wash load.  
Read the Washer Operating Instructions for operating your specific model.  
Always read and follow fabric care and laundry product labels.  
To reduce the risk of fire, electrical shock, or injury to persons, read  
Important Safety Instructions before operating this washer.  
1. Sort laundry into loads that can be washed together.  
Sort items by recommended water temperatures, wash time, and agitate/spin  
speeds.  
Separate white, light, and colorfast items from dark and noncolorfast items.  
Separateitemswhichshedlintfromitemswhichattractlint.Permanentpress,  
synthetic, knit and corduroy items will pick up lint from towels, rugs and  
chenille bedspreads.  
Sort laundry into loads that can be  
washed together.  
Separate heavily soiled items from lightly soiled items.  
Separate lacy, sheer and loosely knit items from sturdy items.  
2. Prepare items for washing.  
Empty pockets.  
Brush off lint and dirt. Shake out rugs and beach towels.  
Closezippers,fastenhooks,tiestringsandsashes,andremovenonwashable  
trims and ornaments.  
Removepins,decorativebuttons,beltbuckles,andotherobjectswhichcould  
be damaged. This also helps protect other items in the wash load.  
Mend rips and tears to prevent further damage during washing.  
Place delicate items such as bras and hosiery in a mesh bag to prevent  
tangling during the wash cycle.  
Empty pockets.  
Turn knit items inside out to prevent pilling.  
3. Pretreat stains and heavy soil.  
See Stain Removal for details.  
4. Add laundry load to washer.  
Combine large and small items in a load. Load large items first. Large items  
should not be more than half the total wash load.  
Washing a single item, such as a sweater, bath towel or jeans, is not  
recommended. As the machine tumbles the load prior to final spin, it may  
sense an out-of-balance load. If an out-of-balance load is sensed, the washer  
willstopbrieflyandtumbleforashorttimetotrytobalancetheload.Thisstop-  
tumble action may occur several times before the end of the cycle. If the load  
cannotbeevenlybalanced,itemsmayfeelwetattheendofthecycle.Adding  
1 or 2 similar items will help balance the load.  
Place delicate items in a mesh bag.  
• Ifaloadbecomestangledandout-of-balance, itmaybenecessarytorearrange  
the load by hand. Stop the washer by pushing in the cycle selector knob and  
openthedoor.Removetheload,untangletheitemsandreturntheloadtothe  
tub. Close the door and restart washer.  
A single bulky item, such as a bedspread, comforter or sleeping bag, can be  
laundered without adding extra items to the load.  
The washer can be fully loaded, but the items should not be tightly packed.  
The door should close easily.  
Add laundry load to washer.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Add detergent, bleach and fabric softener to automatic dispenser following these steps:  
B. DETERGENT  
• Addmeasureddetergenttothedetergentcompartment  
A. OPENINGANDCLOSINGTHEDISPENSERDRAWER  
• Slowly open the dispenser drawer by first sliding the  
safety latch to the right, then pulling the drawer out  
until it stops.  
of the dispenser drawer.  
• Detergentisflushedfromthedispenseratthebeginning  
of the cycle. Either powdered or liquid detergent can  
be used. Note: Liquid detergent will drain into the  
washer drum as it is added.  
• Lowsudsingdetergentisrecommendedforthiswasher.  
Use the manufacturer's recommended amount.  
• If low sudsing detergent is not available, a reduced  
amount of regular detergent may be used. Because  
reducingtheamountofdetergentmayreducecleaning,  
it is important to pretreat stains, sort carefully by color  
and soil level, and avoid overloading.  
• Afteraddinglaundryproducts,slowlyclosethedispenser  
drawer. Closing the drawer too quickly could result in  
early dispensing of the bleach and fabric softener.  
• Dispenser drawer should be completely closed for  
powdered detergent, bleach and fabric softener to  
despense.  
• Laundryproductsusedwithpowderorliquiddetergent,  
suchascolor-safebleach,waterconditioner,detergent  
booster,andenzymeproductsshouldbeaddedtothe  
empty tub before loading.  
• Detergent usage may need to be adjusted for water  
temperature, water hardness, size and soil level of the  
load.  
Note: Fromtimetotimeyoumayseewaterinthebleach  
and fabric softener compartments. This is a result of the  
siphoningactionandispartofthenormaloperationofthe  
washer.  
• For best results, avoid oversudsing.  
D. FABRICSOFTENER  
C. LIQUIDBLEACH  
• If desired, pour the recommended amount of fabric  
softenerintothecompartmentlabeled"FabricSoftener"  
and marked with this symbol  
• Diluteconcentratedsoftenerswithwarmwatertothe  
Fill Line.  
• Do not exceed the maximum fill line. Overfilling can  
cause early dispensing of the fabric softener which  
could result in stained clothes.  
Do not pour fabric softener directly on the wash  
load.  
• If desired, measure out the recommended amount of  
liquid chlorine bleach (not to exceed 1/3 cup (80 mL))  
and pour it into the center compartment labeled  
.
"Liquid Bleach" and marked with this symbol  
.
• Do not exceed the maximum fill line. Overfilling can  
causeearlydispensingofthebleachwhichcouldresult  
in damaged clothes.  
• Do not pour undiluted liquid chlorine bleach directly  
onto the load or into the drum. Fabric damage can  
occur.  
• Use of a fabric softener dispensing ball is not  
recommended in tumble action washers.  
Do not use powdered bleach in the dispenser.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Set cycle selector knob and washer controls according to  
type, size, and soil level of each load.  
Washing Procedures  
(continued)  
(See Operating Instructions card for your specific model controls.)  
7. Start the washer.  
Close the washer door and pull out the cycle selector knob. For your safety, the  
doorwillautomaticallylockduringtheentirewashcycle. TheDoorLockindicator  
light will remain lit until the cycle ends.  
Washer will fill and tumble.  
To stop the washer, push in the cycle selector knob.  
To open the door during tumbling, push in the cycle selector knob. Wait for  
the water to run off of the door.  
To change a cycle, push in the cycle selector knob and turn it clockwise to  
the desired setting. Pull out the knob to restart the washer.  
Toopenthedoorduringaspincycle,pushinthecycleselectorknob. TheDoor  
Lockindicatorlightwillturnoff. Wait1-2minutesforthelocktorelease. The  
door can then be opened. Do not force open the locked door.  
8. Remove items when the cycle is completed.  
Place washed items in automatic dryer, line dry, or dry flat as directed by fabric  
carelabel.Excesswrinkling,colortransferorodorsmaydevelopinitemsleftinthe  
washer after the cycle has ended.  
9. General Precautions  
Do not open the dispenser drawer when the washer is running.  
Do not slam the washer door closed or try to force the door open when  
locked (Door Lock light ON). This could result in damage to the washer.  
DONOTleavethewasherdooropen.Anopendoorcouldenticechildrento  
hang on the door or crawl inside the washer.  
• To avoid damaging the washer and personal injury, DO NOT hang on or lean  
against the washer door.  
Do not store or place laundry products  
on top of laundry center at any time.  
They can damage the finish or  
controls.  
• Do not place detergent, bleach or fabric softener containers on top of the  
washer. They can damage the finish or controls.  
Safe Stain Removal Procedures  
Stain Removal  
To reduce the risk of fire or serious injury to persons or property,  
comply with the basic warnings listed below:  
Do not use or mix  
liquid chlorine bleach with other  
household chemicals such as toilet  
cleaners, rust removers, acid or  
productscontainingammonia.These  
mixtures can produce dangerous  
fumeswhichcancauseseriousinjury  
or death.  
• Read and comply with all instructions on stain removal products.  
• Keep stain removal products in their original labeled containers and out of  
children's reach.  
• Thoroughly wash any utensil used.  
• Do not combine stain removal products, especially ammonia and chlorine  
bleach. Dangerous fumes may result.  
• Never wash items which have been previously cleaned in, washed in, soaked  
in or spotted with gasoline, dry cleaning solvents or other flammable or  
explosive substances because they give off vapors that could ignite or  
explode.  
• Never use highly flammable solvents, such as gasoline, inside the home.  
Vapors can explode on contact with flames or sparks.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
STAIN  
Adhesive tape, chewing gum,  
rubber cement  
                                               
                                               
                                                 
                                                 
                                                   
                                                   
                                                     
                                                     
                                                       
                                                       
                                                         
                                                         
                                                            
                                                            
                                                              
                                                              
                                                                
                                                                
For successful stain removal:  
Remove stains promptly.  
Determine the kind of stain, then follow the recommended treatment in the  
stain removal chart below.  
To pretreat stains, use a prewash product, liquid detergent, or a paste made  
from granular detergent and water.  
Use cold water on unknown stains because hot water can set stains.  
Check care label instructions for treatments to avoid on specific fabrics.  
Check for colorfastness by testing stain remover on an inside seam.  
Rinse and wash items after stain removal.  
Followfabriccarelabelinstructions.  
StainRemoval  
TREATMENT  
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or  
nonflammable dry cleaning fluid.  
Baby formula, dairy products,  
egg  
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.  
Pretreat stain. Wash using cold water and bleach safe for fabric.  
Beverages(coffee,tea,soda,juice,  
alcoholic beverages)  
Blood  
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using  
bleach safe for fabric.  
Candle wax, crayon  
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is  
absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable  
dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.  
Chocolate  
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.  
Pretreat with prewash stain remover or rub with bar soap.  
Collar or cuff soil, cosmetics  
Dye transfer on white fabric  
Grass  
Use packaged color remover. Wash using bleach safe for fabric.  
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.  
Grease,oil,tar(butter,fats,salad  
dressing, cooking oils,  
car grease, motor oils)  
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply  
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse thoroughly. Wash  
using hottest water safe for fabric.  
Ink  
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured  
alcohol or nonflammable dry cleaning fluid.  
Mildew, scorch  
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly  
mildewed fabrics may be permanently damaged.  
Mud  
Brush off dry mud. Pretreat or soak with product containing enzymes.  
Pretreat with prewash stain remover. Wash using bleach safe for fabric.  
Mustard, tomato  
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.  
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.  
Nail polish  
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL  
BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly before washing.  
Paint, varnish  
Perspiration  
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for  
fabric.  
Rust, brown or yellow  
discoloration  
Use rust remover safe for fabric. Do not use chlorine bleach because it may intensify discoloration.  
Shoe polish  
LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric. Pretreat  
with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area.  
Wash using bleach safe for fabric.  
Urine, vomit, mucus, feces  
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Washing Problems  
Manywashingproblemsinvolvepoorsoilandstainremoval,residuesoflintandscum,andfabricdamage.Forsatisfactorywashing  
results, follow these suggestions provided by The Soap and Detergent Association.  
POSSIBLE CAUSES  
PROBLEM  
SOLUTIONS  
PREVENTIVE MEASURES  
•If caused by detergent, mix 1 cup (240  
ml) white vinegar with 1 quart (.95 L)  
water in a plastic container. Soak item 1  
hour. Rinse.  
Blue stains  
•Avoid pouring liquid deterent directly onto  
fabric.  
•Avoid overfilling fabric softener  
compartment of dispenser.  
Undiluted liquid detergent or fabric  
softener dispensed directly onto  
fabric.  
•If caused by fabric softener, rub stains  
with bar soap. Wash.  
•Not enough detergent.  
•Wash water temperature too  
low.  
•Rewash with correct amount of  
detergent and hottest water safe for  
fabric. Add bleach safe for fabric.  
Discoloration,  
graying  
•Sort items by soil level and color.  
•Use correct amount of detergent, hottest  
water and bleach safe for fabric.  
•Incorrect sorting.  
•Treat with prewash stain remover or  
liquid detergent.  
•Increase detergent and water  
temperature. Rewash.  
•Use correct amount of detergent and  
hottest water safe for fabric.  
Do not pour liquid fabric softener  
directly on fabric. See Washing  
Procedures for directions on adding  
softener.  
•Not enough detergent.  
•Undiluted liquid fabric softener  
poured directly on fabric.  
Greasy, oily stains  
•Rub fabric softener stains with bar soap.  
•May be irreversible if rips, tears and  
seams cannot be mended.  
Holes, tears, or  
snags  
•Never pour chlorine bleach directly on  
fabric.  
•Check condition of items before washing.  
See Washing Procedures for preparing  
and loading the wash load and adding  
chlorine bleach.  
•Incorrect use of chlorine bleach.  
•Unfastened zippers, hooks,  
buckles.  
•Rips, tears and broken threads.  
•Overloading the washer.  
•Degradation of fabric.  
•Reduce load size. Rewash using correct  
water temperature, water level, and  
amount of detergent.  
•Add nonprecipitating water conditioner  
to wash water to remove detergent  
residue.  
•Add liquid fabric softener to final rinse.  
•Dry load in dryer.  
•Remove lint with lint brush or roller.  
Lint  
•See Washing Procedures for sorting and  
preparing the wash load.  
•Do not overload washer.  
•Use correct temperature and amount of  
detergent, water and wash time.  
•Incorrect sorting.  
•Tissues left in pocket.  
•Overloading the washer.  
•Not enough detergent.  
•Undissolved detergent has left a  
residue resembling lint.  
•Static cling is attracting lint.  
•Load washed too long.  
•Pilling is normal with synthetic and  
permanent press fabrics. This is  
due to abrasion from normal  
wear.  
•Use a lint brush or shaver to remove  
pills.  
Pilling  
•Use fabric softener in the washer to  
lubricate fibers.  
•When ironing, use spray starch or fabric  
finish on collars and cuffs.  
(Fibers break off,  
ball up and cling to  
fabric.)  
•Turn items inside out to reduce abrasion.  
•Rewash load.  
•Increase water temperature using hottest  
water safe for fabric.  
•Do not overload washer.  
•Use liquid detergent or use nonprecipitating  
water conditioner with granular detergent.  
•Undissolved detergent.  
Residue or powder  
on dark items;  
stiff,  
•Some granular detergents can  
combine with hard water  
minerals to form a residue.  
•Overloading the washer.  
harsh fabrics.  
•Reduce load size.  
Wrinkling  
•Do not overload washer.  
•Remove items from washer as soon as cycle  
is completed.  
•Overloading the washer.  
•Incorrect wash cycle for wash  
load.  
•Rinse in cold water with liquid fabric  
softener using the permanent press or  
delicate cycle.  
•Use liquid fabric softener.  
•Soak in detergent booster or product  
containing enzymes.  
•Wash in hot water using full permanent  
press cycle. Increase detergent.  
•Add bleach safe for fabric.  
Yellow buildup of  
body soil on  
synthetic fabrics  
•Select correct wash cycle.  
•Use correct amount of detergent.  
•Wash synthetics frequently using hot or  
warm water.  
•Wash time too short.  
•Wash water temperature too  
low.  
•Not enough detergent.  
•Or, treat with color remover.  
•To restore discolored load of whites, use  
rust remover safe for fabric.  
•Do not use chlorine bleach to remove  
rust stains. It may intensify  
discoloration.  
Yellow or brown  
rust stains  
•Use nonprecipitating water softener.  
•Before washing, run hot water for a few  
minutes to clear lines.  
•Drain water heater occasionally.  
•For an ongoing problem, install an iron filter  
in your water supply system.  
•Iron or manganese in water  
supply, water pipes, or water  
heater.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Follow the guidelines below for preparing the load for drying.  
Drying Procedures  
Read the Dryer Operating Instructions for operating your specific model.  
• Always read and follow fabric care labels and laundry product labels.  
To reduce the risk of fire, electrical shock, or injury to persons, read  
Important Safety Instructions before operating this dryer.  
1. Prepare items for drying.  
Dry items of similar fabric, weight and construction in the same load.  
Separate dark items from light-colored items. Separate items that shed lint  
from those that attract lint. If an item sheds lint, turn it inside out.  
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum  
finish.Closezippers,fastenhooksandVelcro®-likefasteners.Tiestringsand  
sashes to prevent tangling.  
If possible, turn pockets inside out for even drying.  
Check for stains which may not have been removed in washing. Dryer heat  
may permanently set some stains. Repeat stain removal process before  
drying.  
Follow fabric care label instructions.  
Place small items in a mesh bag to prevent tangling and for easy removal.  
2. Check that lint screen is clean and in place.  
3. Load the dryer.  
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble  
freely for even drying and less wrinkling. Do not overload dryer.  
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall  
and medium sized items.  
For delicate or very small loads, add 2 lint-free towels for better drying, less  
wrinkling, and to prevent grease stains caused by fabric softener sheets.  
Place small items in a mesh bag.  
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,  
and a build-up of static electricity, which can produce more lint.  
If desired, add a dryer fabric softener sheet.  
4. Close the dryer door and set dryer controls (some models).  
See Dryer Operating Instructions for your specific model controls.  
5. Turn cycle selector clockwise to the desired setting.  
6. Start the dryer.  
PushStartButtonfor2secondsorturntheSTARTknobclockwisetoON,hold  
for 1-2 seconds and release.  
Toaddorremoveitemswhenthedryerisrunning,openthedoor.Thedryer  
will always stop when the door is opened. Allow the drum to come to a  
complete stop before reaching inside.  
To restart dryer, close the door then push the Start Button for 2 seconds or  
turn the START knob clockwise to ON, hold for 1-2 seconds and release.  
The dryer will not start if the cycle selector is in the OFF position.  
Fill dryer drum 1/3 to 1/2 full.  
7. When the cycle ends, remove items immediately and hang  
or fold. If load is removed before the cycle ends, turn cycle selector to OFF.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cycle Signal Control (some models)  
Features  
WhentheCycleSignalControlisON, asignalwillsoundattheendofeachcycleand  
during the Press Saver setting (some models). The volume is adjustable on some  
models.  
Drum Light (some models)  
Adrumlightwillcomeonwheneverthedoorisopenedtoilluminatethedryerdrum  
during loading and unloading. Closing the door turns off the light.  
Drying Rack (some models)  
Use the drying rack to dry items which should not be tumble dried.  
1. Open the dryer door and remove the lint screen.  
2. Insertdryingrackintothedryerdrum. Placethefrontbarunderthelipofthelint  
screen opening.  
3. Place items to be dried on top of rack. Weight should not exceed 10 lbs. Leave  
space between items, but do not let items hang over the sides or through the  
grids. Do not tumble other items when using the drying rack.  
4. Selectatimeddrysettingbestsuitedforitemsbeingdried. UseonlytheAirFluff  
(noheat)temperaturesettingforitemscontainingplastic,foamrubber,rubber-  
like materials, feathers or down.  
Use the drying rack to dry items which should  
not be tumbled.  
5. When items are dry, remove the rack and replace the lint screen. If lint screen  
isnotinplace,tumblingitemscouldentertheexhaustsystemandcausedamage  
to the dryer.  
Common Drying  
Problems  
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.  
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.  
PREVENTIVEMEASURES  
PROBLEM  
POSSIBLECAUSES  
SOLUTIONS  
Greasy, oily  
stains  
•Rub fabric softener stains with bar  
soap. Rinse and rewash.  
•Add a few bath towels to small loads for proper  
tumbling.  
•Fabric softener sheet.  
•Some "silk-like" fabrics should be air dried.  
•Use proper drying temperature.  
•Place fabric softener sheet on top of load before  
starting the dryer.  
Lint  
•Reduce load size and rewash using  
liquid fabric softener in the final rinse.  
•Or, add a fabric softener sheet and  
tumble at low heat for 5-10 minutes.  
•Use lint brush or roller to remove lint.  
•Do not overload dryer.  
•Use fabric softener in washer or dryer to reduce  
static electricity.  
•Remove items when they are slightly damp to  
avoid overdrying.  
•Overloading.  
•Overdrying causes static  
electricity.  
•Lint screen not clean when  
cycle began.  
•Check that lint screen is clean and in place.  
•Lint is attached to "pills."  
Pilling  
•Use a lint brush or shaver to remove  
pills.  
•Use fabric softener to lubricate fibers.  
•When ironing, use spray starch or fabric finish on  
collars and cuffs.  
•Pilling is normal with synthetic  
and permanent press fabrics.  
This is due to abrasion from  
normal wear.  
(Fibers break off,  
ball up and cling  
to fabric.)  
•Turn items inside out to reduce abrasion.  
Shrinking  
Wrinkling  
•Irreversible condition.  
•Follow fabric care label directions.  
•If shrinking is a concern, check load often.  
•Remove items while slightly damp.  
•Block knits into shape.  
•Overdrying.  
•Lay flat to complete drying.  
•Reduce load size and tumble at low  
heat for 5-10 minutes.  
•Remove items immediately. Hang or  
fold.  
•Do not overload dryer.  
•Remove items as soon as cycle ends.  
•Overloading.  
•Leaving items in dryer after  
cycle ends.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and Cleaning  
To reduce risk of fire or serious injury to persons or property, comply  
with the basic warnings listed in Important Safety Instructions and those listed  
below.  
Beforecleaningthewasherordryerinterior,unplugtheelectricalpowercord  
to avoid electrical shock hazards.  
Donotuseanytypeofspraycleanserwhencleaningthedryerinterior.Hazardous  
fumes or electrical shock could occur.  
Cleaning the Dispenser Drawer Area  
Detergent and fabric softener may build up in the dispenser drawer. Residue should  
be removed once or twice a month.  
Figure 1  
Remove the drawer by first sliding the safety latch to the right, then pulling  
the drawer out until it stops. (Figure 1)  
(Lock tab is visible only after drawer has  
been pulled out)  
Reach back into the left rear corner of the drawer cavity and press down  
firmly on the lock tab (left rear portion of the drawer). Pull out the drawer.  
(Figure 2)  
Remove the inserts from the bleach and fabric softener compartments.  
(Figure 3)  
Rinse the drawer and inserts with hot tap water to remove traces of  
accumulatedpowdersandliquids. Largeamountsoffabricsoftenerresidue  
may indicate improper dilution or more frequent cleaning is required.  
Tocleanthedraweropening, useasmallbrushtocleantherecess. Remove  
all residue from the upper and lower parts of the recess. (Figure 4)  
Figure 2  
Returnthebleachandfabricsoftenerinsertstotheirpropercompartments.  
Replacethedispenserdrawerandruntheshortwashcyclewithoutanywash  
load in the drum.  
Inside  
Removeitemsfromthewasherassoonasthecycleends.Excesswrinkling,color  
transfer, and odors may develop in items left in the washer.  
Beforecleaningthewasherinterior,unplugtheelectricalpowercordtoavoid  
electrical shock hazards.  
Dryaroundthewasherdooropening,flexiblegasket,anddoorglass.Theseareas  
should always be clean to ensure a water tight seal.  
Figure 3  
When extremely soiled items have been washed, a dirty residue may remain on  
the drum. Remove this by wiping the drum with a nonabrasive household  
cleanser. Rinse thoroughly with water.  
The plastic drum vanes may become stained from fabric dye. Clean these parts  
withanonabrasivehouseholdcleanser.Thispreventsdyetransfertofutureloads.  
Figure 4  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and Cleaning  
Inside the Dryer  
Clean the dryer lint screen after every load. Lint build-up in the screen restricts  
air flow, which causes longer drying times. The screen is located at the bottom  
ofthedooropening.Removebypullingstraightup.Removethelintandreplace  
the screen.  
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added  
fabric softener sheets. To remove this build-up, wash the lint screen in warm,  
soapy water. Dry thoroughly and replace. Do not operate the dryer without the  
lint screen in place.  
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith  
a damp cloth and a mild liquid household cleanser. Remove cleanser residue  
before drying the next load.  
Every 18 months an authorized servicer should clean the dryer cabinet interior  
and exhaust duct. These areas can collect lint and dust over time. An excessive  
amountoflintbuild-upcouldresultininefficientdryingandpossiblefirehazard.  
Outside  
Clean lint screen after every load.  
When laundering is completed, wipe cabinet with a damp cloth. Turn water  
faucets off to prevent pressure build-up in the hoses.  
Clean the cabinet with mild soap and water. Never use harsh, gritty or  
abrasivecleansers.Ifthecabinetbecomesstained,cleanwithdilutedchlorine  
bleach [1/2 cup (120 ml) in 1 quart (.95 L) water]. Rinse several times with clear  
water.  
Remove glue residue from tape or labels with a mixture of warm water and mild  
detergent. Or, touch residue with the sticky side of the tape or label.  
Beforemovingthelaundrycenter,placeastripofcardboardorthinfiberboard  
under the front leveling legs to prevent floor damage.  
Wash lint screen occasionally.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WinterizingInstructions  
Ifthelaundrycenterisstoredinanareawherefreezingcanoccurormovedinfreezing  
temperatures,followthesewinterizinginstructionstopreventdamagetothelaundry  
center:  
FollowWinterizing  
Instructions for cold  
weather care.  
1. Turn off water supply faucets.  
2. Disconnect hoses from water supply and drain water from hoses.  
3. Plug electrical cord into a properly grounded electrical outlet.  
4. Add1gallonnontoxicrecreationalvehicle(RV)antifreezetoempty washdrum.  
Close door.  
5. Set cycle selector knob at a spin setting. Pull out knob and let washer spin for  
1 minute to drain out all water. Not all of the RV antifreeze will be expelled.  
6. Push in knob, unplug electrical power cord, dry tub interior, and close door.  
7. Store washer in an upright position.  
8. To remove antifreeze from washer after storage, run empty washer through a  
complete cycle using detergent. Do not add wash load.  
Avoid Service Checklist  
Before calling for service, review this list. It may save both time and expense. The list includes common concerns that are not the  
result of defective workmanship or materials in this laundry center.  
POSSIBLE CAUSE / SOLUTION  
OCCURRENCE  
NOISE  
"Clicking" noise.  
• A normal sound made by the timer.  
High pitch "jet engine" noise.  
Rattling and clanking noise.  
• A certain amount of motor whine is normal during the spin cycle.  
• Foreign objects such as coins or safety pins may be in drum or pump. Stop washer  
and check drum. If noise continues after washer is restarted, objects may be in  
pump. Call your authorized servicer.  
• Belt buckles and metal fasteners are hitting wash drum. To prevent unnecessary  
noise and damage to drum, fasten fasteners and turn items inside out.  
Squealing sound or hot rubber odor.  
Thumping sound.  
• Washer is overloaded. Do not overload washer. Stop washer and reduce load.  
• Heavy wash loads may produce a thumping sound. This is usually normal. If sound  
continues, washer is probably out of balance. Stop washer and redistribute wash  
load.  
Vibrating noise.  
• Washerisnotrestingfirmlyonfloor.Movewashersoitrestsfirmlyonfloor.Adjust  
leveling legs. See INSTALLATION INSTRUCTIONS for details.  
• Shipping bolts and foam block have not been removed during installation. See  
INSTALLATION INSTRUCTIONS for removing shipping bolts and foam block.  
• Wash load unevenly distributed in drum. Stop washer and rearrange wash load.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POSSIBLE CAUSE / SOLUTION  
OCCURRENCE  
• Electrical power cord may not be plugged in or connection may be loose. Make  
sure plug fits tightly in wall outlet.  
OPERATING  
• House fuse blown, circuit breaker tripped, or a power outage has occurred. Reset  
circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit  
overload, haveitcorrectedbyaqualifiedelectrician. Ifproblemisapoweroutage,  
call local electric company.  
Washer does not start.  
• Water supply faucets are not turned on. Turn on water supply faucets.  
• Cycle selector is not in correct position. Move indicator clockwise slightly. Pull out  
knob.  
• Motor is overheated. Washer motor will stop if it becomes overheated. It will  
automatically restart after a cool down period of up to 30 minutes (if washer has  
not been manually turned off).  
• Washer door is not completely closed. Close door completely.  
Washer won't spin.  
Residue left in drum.  
• Load is too small. Add 1 or 2 similar items to help balance the load.  
• Heavilysoileditems.Wipedrumwithanonabrasivehouseholdcleanser,thenrinse.  
Shake or brush excess dirt and sand from items before washing.  
Laundry additives didn't dispense.  
• Dispenserdraweropen. Drawershouldbecompletelyclosedforlaundryadditives  
to dispense.  
WATER  
• This is a result of the siphoning action and is part of the normal operation of the  
washer. Water may be removed by removing the dispenser drawer (see Page 11,  
Figures 1 and 2) and draining water into the empty drum or sink.  
Water collects in bleach and fabric  
softenercompartments.  
Wash load too wet after spin.  
• Washer is overloaded. Do not overload washer. See Washing Procedures.  
• Load is too small. Add 1 or 2 similar items to help balance the load.  
• Load is out of balance. Rearrange load to allow proper spinning.  
• Drain hose is kinked. Straighten drain hose.  
Water does not enter washer or it  
enters slowly.  
• Watersupplyisnotadequateinarea.Checkanotherfaucetinthehouse.Waituntil  
water supply and pressure increase.  
• Water supply faucets are not completely open. Fully open hot and cold faucets.  
• Water is being used elsewhere in the house. Water pressure must be at least 30  
psi (260 kPa). Avoid running water elsewhere while washer is filling.  
• Water inlet hoses are kinked. Straighten hoses.  
Warm or hot water is not hot  
enough.  
• Hot water heater is set too low or is a distance from washer. Measure hot water  
temperatureatnearbyfaucetwithcandyormeatthermometer.Watertemperature  
should be at least 120°F (49°C). Adjust water heater as necessary.  
• Hot water is being used elsewhere in the house. Avoid using hot water elsewhere  
before or during washer use. There may not be enough hot water available for  
proper cleaning. If problem persists, your hot water system may be unable to  
support more than 1 use at a time.  
Water in washer does not drain or  
drains slowly.  
• Drain hose is kinked or clogged. Clean and straighten the drain hose.  
• House drain pipes are clogged. Unclog drain pipes. Contact plumber if necessary.  
• Fill hose connection is loose at faucet or washer. Check and tighten hose  
connections. Install rubber sealing washers provided.  
Waterleaks.  
• Oversudsing. Use less detergent.  
• Dispenser drawer is open. Close dispenser drawer when washer is operating.  
• Hot and cold water hoses are connected to wrong supply faucets. Connect hot  
water hose to hot water faucet and cold water hose to cold water faucet.  
Incorrect wash and rinse  
temperatures.  
• Drain hose standpipe is incorrect height. Standpipe must be a minimum of 23.6"  
(60 cm) high to prevent siphoning. See INSTALLATION INSTRUCTIONS.  
Water is entering washer but tub  
does not fill.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OCCURRENCE  
DRYER  
POSSIBLE CAUSE  
SOLUTION  
Dryer does not start.  
Make sure the plug fits tightly in wall outlet.  
Electrical power cord is not securely  
plugged in or plug may be loose.  
Reset circuit breaker or replace fuse.  
House fuse blown or circuit breaker  
tripped.  
Make sure electrical line is not overloaded and the dryer  
is on a separate circuit.  
Call authorized service person for replacement.  
Replace fuse.  
Thermal limiter tripped.  
Dryer runs but won't  
heat.  
There are 2 house fuses in the dryer  
circuit. If 1 of the 2 fuses is blown, the  
drum may turn but the heater will not  
operate.  
Check to make sure supply valve is open. See  
INSTALLATION INSTRUCTIONS for procedure.  
Gas supply valve is not open (gas models).  
See INSTALLATION INSTRUCTIONS.  
Dryer does not have enough air supply to  
support the burner flame (gas models).  
Refill or replace tank.  
LP gas supply tank is empty or there has  
been a utility interruption of natural gas  
(gas models).  
Dryer should heat when utility service is restored.  
Drying cycle takes too  
long, outsideofthedryer  
feels too hot or smells  
hot.  
Make sure all lint has been removed from the dryer lint  
screen before starting each cycle.  
Lint screen is clogged with lint.  
Exhaust duct must be at least 4 inches in diameter and  
made of rigid or flexible metal.  
Exhaust duct requirements have not been  
met.  
When in place, the duct must have no more than two  
90° bends and must not exceed length listed in  
INSTALLATION INSTRUCTIONS.  
Drying time will be 20% longer than drying on a 240 volt  
circuit.  
Electric dryer is connected to a 208 volt  
circuit.  
See Drying Procedures.  
Drying procedures have not been  
followed.  
Clean out any obstruction.  
Outside exhaust hood or exhaust duct  
may be clogged or restricted.  
Use a dehumidifier near the dryer.  
Do not overload. See Drying Procedures.  
Remove items as soon as cycle ends.  
See Drying Procedures.  
High humidity.  
Excessive wrinkling.  
Dryer is overloaded.  
Items left in dryer too long.  
Insufficient sorting of items.  
Drying temperature too high.  
Follow fabric care label instructions.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Major Appliance Warranty Information  
Your appliance is covered by a one year limited warranty. For one year from your original date of  
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to  
be defective in materials or workmanship when such appliance is installed, used and maintained in  
accordance with the provided instructions.  
Exclusions  
This warranty does not cover the following:  
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.  
2. Product that has been transferred from its original owner to another party or removed outside the USA or  
Canada.  
3. Rust on the interior or exterior of the unit.  
4. Products purchased "as-is" are not covered by this warranty.  
5. Food loss due to any refrigerator or freezer failures.  
6. Products used in a commercial setting.  
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances  
not in ordinary household use or used other than in accordance with the provided instructions.  
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.  
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,  
etc.,which are not a part of the appliance when it is shipped from the factory.  
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or  
knobs, handles, or other cosmetic parts.  
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip  
charges, or mileage expense for service calls to remote areas, including the state of Alaska.  
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,  
cabinets, walls, etc.  
13. Damages caused by: services performed by unauthorized service companies; use of parts other than  
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or  
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.  
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES  
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT  
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,  
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE  
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.  
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS  
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN  
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE  
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE  
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO  
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER  
RIGHTS THAT VARY FROM STATE TO STATE.  
If You Need  
Service  
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period  
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.  
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone  
numbers below.  
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances  
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada  
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and  
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or  
specifications as described or illustrated are subject to change without notice.  
USA  
Canada  
1.800.944.9044  
Electrolux Major Appliances  
North America  
1.800.668.4606  
Electrolux Canada Corp.  
5855 Terry Fox Way  
P.O. Box 212378  
Augusta, GA 30907  
Mississauga, Ontario, Canada  
L5V 3E4  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Excalibur electronic Games 414PE BK User Manual
Extron electronic TV Mount WMK 100 User Manual
Fellowes Paper Shredder 120 User Manual
Frymaster Fryer D50 Series User Manual
Frymaster Fryer Series H50 User Manual
Fujitsu Printer FTP 639MCL054 User Manual
Furman Sound Power Supply ElitE 20 PF User Manual
Fusion Car Speaker MS BX3020 User Manual
GE Monogram Trash Compactor ZCG3500DSS User Manual
GE Refrigerator 162D3907P004 User Manual