All about the
Use&Care
of your Refrigerator
TABLE OF CONTENTS
Important Safety Instructions......................2
Features at a Glance...................................4
Installation ................................................5
Door Removal Instructions..........................7
Handle Installation .....................................9
Connecting Water Supply..........................10
Controls...................................................12
Storage Features......................................14
Automatic Ice & Water Dispenser ..............16
Changing the Filter...................................19
Normal Operating Sounds and Sights.........21
Care and Cleaning....................................22
Before you Call.........................................24
Major Appliance Warranty.........................27
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
• If the power cord is damaged, it should
be replaced by an authorized service
technician to prevent any risk.
Proper Disposal of your
Refrigerator or Freezer
Risk of child entrapment
• Never unplug the refrigerator by pulling on
the power cord. Always grip the plug firmly,
and pull straight out from the receptacle to
prevent damaging the power cord.
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators or freezers are still dangerous
– even if they will sit for “just a few days”. If
you are getting rid of your old refrigerator or
freezer, please follow the instructions below to
help prevent accidents.
• Unplug the refrigerator before cleaning
and before replacing a light bulb to avoid
electrical shock.
• Performance may be affected if the voltage
varies by 10% or more. Operating the
refrigerator with insufficient power can
damage the compressor. Such damage is
not covered under your warranty.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your
utility company or visit
information on recycling your old refrigerator.
• Do not plug the unit into an electrical outlet
controlled by a wall switch or pull cord to
prevent the refrigerator from being turned
off accidentally.
Before you throw away your old
refrigerator/freezer:
• Remove
doors.
IMPORTANT
• Leave
shelves in
place so
children may
not easily
climb inside.
Pressing and holding the On/Off button for
three seconds, located on the temperature
control panel (Electronic controls), or turning
the Freezer and Fresh Food controls to
“0” (Mechanical controls) will disable your
refrigerator’s cooling system, but does not
disconnect the power to the light bulb and
other electrical components. To turn off power
to your refrigerator you must unplug the
power cord from the electrical outlet.
• Have
refrigerant
removed by
a qualified
service technician.
Grounding type wall receptacle
WARNING
Do not, under
any circumstances,
cut, remove,
These guidelines must be followed to ensure
that safety mechanisms in this refrigerator
will operate properly.
or bypass the
grounding prong.
Electrical information
• The refrigerator must be plugged into its
own dedicated 115 Volt, 60 Hz., 15 Amp,
AC only electrical outlet. The power cord
of the appliance is equipped with a three-
prong grounding plug for your protection
against electrical shock hazards. It must be
plugged directly into a properly grounded
three prong receptacle. The receptacle must
be installed in accordance with local codes
and ordinances. Consult a qualified electrician.
Avoid connecting refrigerator to a Ground
Fault Interrupter (GFI) circuit. Do not use an
extension cord or adapter plug.
Power cord with
3-prong gounded plug
CAUTION
To avoid personal injury or property damage,
handle tempered glass shelves carefully. Shelves
may break suddenly if nicked, scratched, or
exposed to sudden temperature change.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AT A GLANCE
Features may vary according to model
SpillSafe®
CAUTION:
Adjustable Shelf
Ice Cream Shelf
Ice Maker
Do Not Remove
Magnet Behind
Dairy
Water Filter
Compartment
Fixed
Door Bin
Dairy
Compartment
Ice
Container
Door Bin
SpillSafe®
Adjustable Shelf
Shelf
Door Bin
Wine Rack
Tall Bottle
Shelf
Tilt Out
Door Bin
Retainer
Door Bin
Special Item
Rack
Meat Keeper
and Cover
Small Basket
Large
Glide Out
Basket
Tilt Out
Door Bin
Can Rack
Crisper Pan
and Cover
Large
Basket
Door Bin
Fixed
Door Bin
Toe Grille
IMPORTANT
Features not included with your refrigerator can be purchased at
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
This Use & Care Guide provides general
operating instructions for your model. Use
the refrigerator only as instructed in this
Use & Care Guide. Before starting the
refrigerator, follow these important first
steps.
Toe Grille Installation and
Removal
To install toe grille
1 Open both doors. Slide left and right
sides of toe grille over lower hinges of
refrigerator.
Location
• Choose a place that is near a grounded
electrical outlet. Do Not use an extension
cord or an adapter plug.
2
While pushing toe grille firmly against
cabinet, fasten bottom clips of toe grille to
cabinet.
3 Fasten top clips to cabinet.
• If possible, place the refrigerator out of
direct sunlight and away from the range,
dishwasher or other heat sources.
4 Close the doors. Fasten right and left side
clips into groove of bottom hinge.
• The refrigerator must be installed on a floor
that is level and strong enough to support
a fully loaded refrigerator.
Installing Toe Grille
4
3
1
• Consider water supply availability for
models equipped with an automatic ice
maker. If you do not hook up water to
the refrigerator, remember to turn the ice
maker off.
4
2
3
2
1
To remove toe grille
CAUTION
1 With both doors closed, unfasten right
and left side clips of toe grille from bottom
hinge groove.
Do Not install the refrigerator where the
temperature will drop below 55°F (13°C) or
rise above 110°F (43°C). The compressor
will not be able to maintain proper
2
Open both doors. Press firmly on top of
toe grille until top of toe grille pops off.
temperatures inside the refrigerator.
3 Pull toe grille outward toward your body
Do Not block the toe grille on the lower front
of your refrigerator. Sufficient air circulation
is essential for the proper operation of your
refrigerator.
and off of lower hinges.
Removing Toe Grille
1
2
Installation
Installation clearances
1
3
2
• Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
3
Sides & Top
Back
3/8 inch
1 inch
NOTE
If your refrigerator is placed with the door
hinge side against a wall, you may have to
allow additional space so the door can be
opened wider.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
To level the doors using the adjustable
lower hinge (some models):
Door Opening
1 Before leveling either door, remove set
screw that locks door height into position.
(The door cannot be adjusted without set
screw removed).
NOTE
The refrigerator doors are designed to shut
by themselves within a 20 degree opening.
2 If the refrigerator door is lower than the
freezer door, raise the refrigerator door by
turning the adjustment screw clockwise
using a 7/16 inch wrench. (See illustration.)
Your refrigerator should be positioned to
allow easy access to a counter or table when
removing food. For best use of drawers and
freezer baskets, the refrigerator should be
in a position where both the refrigerator and
freezer doors can be fully opened.
3 If the freezer door is lower than the
refrigerator door, raise the freezer door by
turning the adjustment screw clockwise
using a 7/16 inch wrench. (See illustration.)
Guidelines for final positioning of
your refrigerator:
• All four corners of the cabinet must rest
firmly on the floor.
Door
Door
• The cabinet should be level at the front
and rear.
• The sides should tilt ¼ inch (6 mm) from
front to back (to ensure that doors close
and seal properly).
Raise
Door
Raise
Door
• Doors should align with each other and be
level.
All of these conditions can be met by raising
or lowering the adjustable front rollers.
4 After leveling, verify door stop contacts
lower hinge and top of door does
not contact upper hinge through full
movement of door (from fully closed to
fully open).
To level the cabinet using the front rollers:
1 Open both doors and remove the toe
grille (see “Toe Grille Installation and
Removal” in the “Installation” section).
5 Reinstall set screw, locking the door
2
Close the doors and use a flat-blade
screwdriver or 3/8 inch socket wrench to
raise or lower the front rollers.
height.
Open Door
Door Stop
3 Ensure both doors are bind-free with their
seals touching the cabinet on all four sides.
Flange
Hinge
Flange
Raise
Set Screw
(some models)
Hinge
7/16" Wrench
and
3/32" Hex Key
(some models)
6
Replace the toe grille by fitting it into
place (see “Toe Grille Installation and
Removal” in the “Installation” section).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR REMOVAL INSTRUCTIONS
2 Open both doors and remove the toe
Outils nécessaires:
grille (as explained in the Installation
Instructions that came with your
appliance).
3 Remove any food from the door shelves.
4 Close the doors.
To remove the refrigerator top
hinge cover:
Tournevis à
tête Phillips™
1 Remove the three screws from each cover
over the top door hinges.
2 Lift hinge cover straight up and off.
Rear Cover
Screw
Front Cover
Screws
Top
Hinge
Cover
or
Hinge
Screws
Clé à
molette
Jeu de clés
à douilles
Top
Hinge
or
Clé
polygonale
de 3/8"
To remove the refrigerator door:
1 Trace lightly around the door’s top hinge
with a pencil. This makes reinstallation
easier.
Top Hinge
Cover Front
Screw
Top Hinge
Cover Rear
Screw
Top
Hinge
Screw
Bottom
Hinge
Screw
Getting through narrow spaces
If your refrigerator will not fit through an
entrance area, you can reduce its size by
removing the doors. Check first by measuring
the entrance.
2 Remove the two screws from the top
hinge. Lift the door off of the bottom
hinge and set it aside.
To prepare for removing the doors:
1 Make sure the electrical power cord is
unplugged from the wall outlet.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR REMOVAL INSTRUCTIONS
3 Remove the two bottom hinge screws and
2 Trace lightly around the hinge with a
hinge if necessary.
pencil. This makes reinstallation easier.
3 Detach the water tube from the connector
located below the freezer door. The
connector releases when you press its
outer sleeve inward.
Door
Hinge
Assembly
4 Remove the screws from the top hinge
and pull the multi-wire cable through it.
Lift the door off of the bottom hinge.
Closer
Pin
5 Remove the two bottom hinge screws and
hinge if necessary.
To Disconnect
1. Press outer ring against face
of fitting
Screws
Hinge
Adjustable Hinge (some models)
2. Pull to
To reinstall the refrigerator door, reverse the
above steps.
To remove the freezer top hinge cover:
remove tube
To Connect
Insert tube and
push until mark touches face of fitting
1 Remove the two screws from each cover
over the top door hinges.
Door
2 Lift hinge cover straight up and off.
Front
Cover Screws
Rear
Cover
Screw
Closer
Top Hinge
Cover
Water
Line
Tubing
Pin
Hinge
Assembly Screws
Hinge
Screws
Hinge
Adjustable Hinge (some models)
Multi-Wire
Cable
Door
Top
Hinge
To remove the freezer door:
Water
Line
Tubing
1 Detach the multi-wire cable connector
located above the top hinge. Grasp both
sides of the connector firmly and pull apart.
Hinge
Assembly
Screws
Non-Adjusting Hinge (some models)
6 Lay the door on its side to avoid damage
to the water tube extending from the
bottom hinge.
To reinstall the freezer door, reverse the above steps.
CAUTION
Be sure doors are set aside in a secure position
where they cannot fall and cause personal injury.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE INSTALLATION
Frigidaire Professional®
Freezer Upper
End Cap
Refrigerator Upper
End Cap
CAUTION
Wear gloves and safety goggles and
use extreme CAUTION when installing
these handles. The rounded end of
the handles may be sharp (some
models).
IMPORTANT
To ensure proper installation of
handles, please review these
instructions and illustrations
thoroughly prior to installing the
handles.
1 Remove handles from carton and
any other protective packaging.
2 Position freezer handle end caps
over upper and lower pre-installed
shoulder bolts (A) that are fastened
into door, ensuring the holes for the
set screws are facing towards the
refrigerator door.
Freezer Lower
End Cap
Refrigerator Lower
End Cap
Frigidaire Gallery®
Freezer Upper
End Cap
Refrigerator Upper
End Cap
3
While holding handle firmly against
door, fasten upper and lower Allen
set screws (B) with supplied Allen
wrench.
4 Repeat steps 2 and 3 to install
refrigerator handle. Ensure the
holes for the set screws are facing
towards the freezer door.
NOTE
All set screws should be tightened
and sub-flush (Allen set screw should
be seated just below the surface of
the end cap) of handle end cap. The
end caps should be drawn tight to
freezer and refrigerator doors with
no gaps.
Freezer Lower
End Cap
Refrigerator Lower
End Cap
Ensure Handle Set Screws
are Facing Each Other
with Doors Closed
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE WATER SUPPLY
• A shutoff valve to connect the water supply
line to your household water system. Do
not use a self-piercing type shutoff valve.
WARNING
• Do not re-use compression fitting or use
To avoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the
refrigerator.
thread seal tape.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to
the ice maker inlet valve.
NOTE
CAUTION
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing your
new refrigerator. Depending on your local/
state building codes, Frigidaire recommends
for homes with existing valves its Smart
Choice® water line kit 5305513409 (with
a 6 ft. Stainless Steel Water Line) and for
homes without an existing valve, Frigidaire
recommends its Smart Choice® water line
kit 5305510264 (with a 20 ft. copper water
line with self-tapping saddle valve). Please
information.
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing
is recommended for the water supply
line. Water supply tubing made of ¼
inch plastic is not recommended to be
used. Plastic tubing greatly increases
the potential for water leaks, and the
manufacturer will not be responsible for
any damage if plastic tubing is used for
the supply line.
• DO NOT install water supply tubing in
areas where temperatures fall below
freezing.
• Chemicals from a malfunctioning softener
can damage the ice maker. If the ice
maker is connected to soft water, ensure
that the softener is maintained and
working properly.
To Connect Water Supply Line To Ice Maker
Inlet Valve
1 Disconnect refrigerator from electric power
source.
2 Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF
water supply at shutoff valve.
IMPORTANT
Ensure that your water supply line
connections comply with all local plumbing
codes.
3 Remove plastic cap from water valve inlet
and discard cap.
4 If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve)
onto water supply line. Push water supply
line into water valve inlet as far as it
will go (¼ inch/6.4 mm). Slide ferrule
(sleeve) into valve inlet and finger tighten
compression nut onto valve. Tighten
another half turn with a wrench; DO NOT
over tighten. See Figure 1.
Before Installing The Water Supply Line, You
Will Need:
• Basic Tools: adjustable wrench, flat-blade
screwdriver, and PhillipsTM screwdriver
• Access to a household cold water line with
water pressure between 30 and 100 psi.
• A water supply line made of ¼ inch
(6.4mm) OD, copper or stainless steel
tubing. To determine the length of tubing
needed, measure the distance from the
ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then
add approximately 7 feet (2.1 meters),
so the refrigerator can be moved out for
cleaning (as shown).
If you use stainless steel tubing - The
nut and ferrule are already assembled on
the tubing. Slide compression nut onto
valve inlet and finger tighten compression
nut onto valve. Tighten another half turn
with a wrench; DO NOT over tighten. See
Figure 2.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE WATER SUPPLY
5 With steel clamp and screw, secure water
Plastic Water Tubing
to Ice Maker
Fill Tube
supply line (copper tubing only) to rear
panel of refrigerator as shown.
Steel
Clamp
6 Coil excess water supply line (copper
tubing only), about 2½ turns, behind
refrigerator as shown and arrange coils so
they do not vibrate or wear against any
other surface.
Stainless
Steel
water line
7 Turn ON water supply at shutoff valve and
tighten any connections that leak.
Water Valve
Bracket
8 Reconnect refrigerator to electrical power
source.
9 To turn ice maker on, lower wire signal
arm (side mounted) or set the ice maker’s
On/Off power switch to the “I” position
(rear mounted).
Valve Inlet
Water Valve
6 ft. Stainless Steel water line
from household water supply
Steel
Plastic Water
Clamp
Tubing to Ice
Figure 2
Brass
Compression
Nut
Maker Fill
Tube
IMPORTANT
Ferrule
(Sleeve)
After connecting the water supply, refer to
“How to Prime the Water Supply System”
for important information about priming an
empty water supply system.
Copper
water line
Water Valve
Bracket
Your refrigerator’s water supply system
includes several tubing lines, a water filter,
a water valve, and a water tank. To ensure
that your water dispenser works properly,
this system must be completely filled
with water when your refrigerator is first
connected to the household water supply
line.
Valve Inlet
Water Valve
Copper water line
from household
water supply
(Include enough tubing in loop
to allow moving refrigerator out
for cleaning.)
Figure 1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
Express-Select®
User Interface
Sabbath Mode
Your refrigerator is equipped with a user interface The Sabbath Mode is a feature that disables
display.
portions of the refrigerator and its controls
in accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Touch an icon (Water/Cube/Crush) to activate
the desired dispenser mode.
light on-off On / Off
control lock Press and hold for three seconds
Sabbath Mode is turned ON and OFF by
pressing and holding "∨" on freezer temp and
"∧" on refrigerator temp for five seconds. The
to activate and deactivate. This
restricts undesired changes to the display shows “Sb” while in Sabbath mode.
refrigerator’s settings and prevents
In the Sabbath Mode, the High Temp alarm is
use of the ice and water dispenser.
active for health reasons. If a high temperature
water filter Touch to display filter condition
alarm is activated during this time, for example
due to a door left ajar, the alarm will sound
intermittently for about 10 minutes. The alarm
will then silence on its own and a red high
temperature icon will display. The high temp
icon will continue to display, even if the door
is closed, until the Sabbath mode is exited and
the icon reset. The refrigerator will function
normally once the door is closed, without any
violation of the Sabbath/Holidays.
status. Press and hold for three
seconds to reset.
Touch to toggle display from Fahr-
enheit to Celsius. Press and hold
for three seconds for display on-off.
When active, it allows the display of
the freezer and fridge temps.
C/F
power on-off Press and hold for three seconds
to turn off the cooling system to
clean the refrigerator. It also turns For further assistance, guidelines for proper
off all dispenser functions. The
temperature display will read OFF.
usage and a complete list of
models with the Sabbath feature,
please visit the web at
IMPORTANT
Pressing the power off icon does not turn off
power to your refrigerator. You must unplug the
power cord from the wall outlet.
NOTE
Although you have entered the Sabbath
mode, the ice maker will complete the
cycle it had already initiated. The ice cube
compartment will remain cold and new ice
cubes can be made with standard trays.
Setting Cooling Temperatures
Press the ∧ or ∨ indicator to adjust the temperature
to the desired setting. The temperature display
will begin to blink with the first touch. After five
seconds of inactivity, the display will beep to accept
the new temperature.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
Express-Select®
the desired setting. After five seconds of inactivity,
User Interface
Your refrigerator is equipped with a user
interface display. It is only necessary to touch
the glass. There is no need to press with force.
the display will beep to accept the new temperature.
Sabbath Mode
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls in
accordance with observance of the weekly
Sabbath and religious holidays within the
Orthodox Jewish community.
Touch an icon (Water/Cube/Crush) to
activate the desired dispenser mode.
light on-off On / Off
control lock Press and hold for three seconds
to activate and deactivate. The
Lock icon will be displayed in
the LCD window. This restricts
undesired changes to the
Sabbath Mode is turned ON and OFF by pressing and
holding power on-off and control lock for five seconds.
The display shows “Sb” while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm is
active for health reasons. If a high temperature
alarm is activated during this time, for example
due to a door left ajar, the alarm will sound
intermittently for about 10 minutes. The alarm
will then silence on its own and a red high
temperature icon will display. The high temp icon
will continue to display, even if the door is closed,
until the Sabbath mode is exited and the icon
reset. The refrigerator will function normally once
the door is closed, without any violation of the
Sabbath/Holidays.
refrigerator’s settings and pre-
vents use of the ice and water
dispenser.
filter reset Touch to display filter condition
status. Press and hold for three
seconds to reset.
C/F
Touch to toggle display from
Fahrenheit to Celsius.
power on-off Press and hold for three seconds
to turn off the cooling system
to clean the refrigerator. It also
turns off all dispenser functions.
The temperature display will
read OFF.
For further assistance, guidelines for proper usage
and a complete list of models with the
Sabbath feature, please visit the web
IMPORTANT
Pressing the power off icon does not turn
off power to your refrigerator. You must
unplug the power cord from the wall outlet.
NOTE
Although you have entered the Sabbath
mode, the ice maker will complete the
cycle it had already initiated. The ice cube
compartment will remain cold and new ice
cubes can be made with standard trays.
Setting Cooling Temperatures
Press set temp to choose which compartment,
refrigerator or freezer, to adjust. The temperature
display will begin to blink with the first touch. Touch
button next to + or - to adjust the temperature to
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE FEATURES
The dairy compartment, which is warmer than the
general food storage section, is intended for short
term storage of cheese, spreads, or butter.
CAUTION
To avoid personal injury or property damage,
handle tempered glass shelves carefully.
Shelves may break suddenly if nicked,
scratched, or exposed to sudden temperature
change. Allow the glass shelves to stabilize
to room temperature before cleaning. Do not
wash in dishwasher.
Fresh Drawers with Humidity
Control (some models)
The fresh drawers, located under the bottom
refrigerator shelf, are designed for storing fruits,
vegetables, and other fresh produce. The fresh
drawers feature humidity control which allows you
to adjust the humidity within the drawer. This can
extend the life of fresh vegetables that keep best
in high humidity. Wash items in clear water and
remove excess water before placing them in the
crispers. Items with strong odors or high moisture
content should be wrapped before storing.
Cantilever Shelf Adjustment
Refrigerator shelves are easily adjusted to suit
individual needs. Before adjusting the shelves,
remove all food. Cantilever shelves are
supported at the back of the refrigerator.
To adjust cantilever shelves:
1
Lift front edge up.
Pull shelf out.
2
Higher Humidity Lower Humidity
Replace the shelf by inserting the hooks at
rear of the shelf into the wall bracket. Lower
the shelf into the desired slots and lock into
position.
Crisper Humidity Control
SpillSafeTM glass shelves (some models) catch
and hold accidental spills. In some models, the
SpillSafeTM shelves slide out for easy access
to food and for fast cleaning. The shelves slide
out independently of their mounting brackets.
Just pull the front of the shelf forward.
Shelves can be extended as far as the stopper
will allow but are not removable from their
mounting brackets.
NOTE
Leafy vegetables keep best when stored
with the humidity control set on Higher
Humidity, or in a drawer without a Humidity
Control. This keeps incoming air to a
minimum and maintains maximum moisture
content.
Crispers
Crispers allow you
the flexibility to store
any manner of items
including fruits,
1
1
2
vegetables, nuts, etc.
Crispers do not feature
humidity controls.
2
Crisper Drawer
Cantilever Glass Shelf
Cool Drawer (some models)
Some models are equipped with a Cool Drawer
for storage of luncheon meats, spreads,
Cantilever Sliding
Glass Shelf
cheeses, and other deli items. This drawer
does not have a separate temperature control.
Door storage
Door bins and shelves are provided for convenient
storage of jars, bottles, and cans. Frequently used
items can be quickly selected.
Some models have door bins that can
accommodate gallon-sized plastic drink containers
and economy-sized jars and containers. Some bins
are adjustable for maximum storage capacity.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE FEATURES
Chill Drawer (some models)
Some models are equipped with a Chill Drawer. Chill Drawer temperatures can be adjusted by
sliding the Chill Drawer Temperature Control in either direction. Use this pan for short term
storage of bulk meat items. If meats are to be kept longer than one or two days, they should be
frozen. The Chill Drawer is fixed and cannot be moved up or down. If fruits or vegetables are to
be stored in the Chill Drawer, set the Chill Drawer Temperature Control to a warmer setting to
prevent freezing.
Colder
Warmer
Chill Drawer
with Temperature Control
15
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE & WATER DISPENSER
Priming the Water Supply System Ice Production: What to Expect
How Much Ice Will a Side Mounted Ice
Maker Produce in 24 Hours?
Your refrigerator’s water supply system includes
several tubing lines, an advanced water filter,
a distribution valve bank, and a reserve tank
to ensure ample supply to the ice and water
dispenser at all times. This system needs to be
completely filled with water when first connected
to an external supply line.
A side mounted ice maker will produce 4 to 4.5
pounds of ice every 24 hours, depending on
usage conditions. Ice is produced at a rate of 8
cubes every 75 to 90 minutes.
How Much Ice Will a Rear Mounted Ice
Maker Produce in 24 Hours?
CAUTION
A rear mounted ice maker will produce 3 to 4
pounds of ice every 24 hours, depending on
usage conditions. Ice is produced at a rate of 8
cubes every 75 to 90 minutes.
For proper dispenser operation, recommended
water supply pressure should fall between 30
psi and 100 psi. Excessive pressure may cause
water filter to malfunction.
Using the Ice Maker after
Installation
To prime the water supply system:
1
Begin filling the tank by pressing and holding
a drinking glass against the water dispenser
paddle.
Before making ice for the first time, be sure
to prime the water supply system. Air in new
plumbing lines can result in two or three empty
ice maker cycles. Furthermore, if the system
is not flushed, the first ice cubes may be
discolored or have an odd flavor.
2 Keep the glass in this position until water
comes out of the dispenser. It may take
about 1½ minutes.
3 Continue dispensing water for about four
minutes to flush the system and plumbing
connections of any impurities (stopping to
empty the glass as necessary).
IMPORTANT
Your ice maker is shipped from the factory
with the wire signal arm in the ON position
(side mounted) or with the switch turned
ON (rear mounted). To ensure proper
function of your ice maker, hook up water
supply immediately or turn ice maker OFF
by lifting the wire signal arm until it clicks
and locks in the UP position (side mounted)
or turn the On/Off switch to the Off (0)
position (rear mounted). If the ice maker
is not turned off and the water supply
is not connected, the water valve will
make a loud chattering noise.
NOTE
The water dispenser has a built-in device that
shuts off the water flow after three minutes of
continuous use. To reset this shutoff device,
simply release the dispenser paddle.
Ice Maker Operation & Care
The ice maker, ice bin, and dispenser feeding
mechanism are located in the top of the freezer
compartment. After the refrigerator is installed
properly and has cooled for several hours, the ice
maker can produce ice within 24 hours. It can
completely fill an ice bin in about two days.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE & WATER DISPENSER
Turning the SIDE MOUNTED Ice
Maker On and Off
IMPORTANT
Small ice cubes or ice chips jamming in the
ice maker may be a sign that your water filter
needs changing. If you have a side mounted
ice maker you may also experience hollow
cubes partially frozen cubes with water inside.
When these cubes are harvested, they break
open and spill water over the other ice cubes
in the ice container, forming a solid mass of
ice. As the water filter nears the end of its
useful life and becomes clogged with particles,
less water is delivered to the ice maker during
each cycle. The ice maker can’t fill every cube
in the ice maker mold, leading to small cubes
or chips that can get caught between the ice
ejector blades and the stripper. Remember,
if your ice maker is jamming with small ice
cubes or it’s been six months or longer since
you last changed your water filter replace
the water filter with a new one. Poor quality
household water may require the filter to be
changed more frequently.
To begin ice production, lower the wire signal
arm to the DOWN or ON position. The ice
maker turns off automatically when the ice
container becomes full. To stop the ice maker,
raise the wire signal arm until it clicks and
locks in the UP or OFF position.
Turning the REAR MOUNTED Ice
Maker On and Off
Ice production is controlled by the ice maker’s
ON/OFF power switch. To gain access to the
ice maker, pull the ice cream shelf out. Press
the switch to the “O” position to turn it Off and
press it to the “I” position to turn it On. The
ice maker also has a built-in wire signal arm,
which automatically stops ice production when
the ice bin is full. DO NOT use this signal arm
to manually stop the ice maker.
ON
Ice Maker/Dispenser Tips
• Ice cubes stored too long may develop
an odd flavor. Empty the ice container as
explained below.
OFF
• Occasionally shake the ice container to
keep ice separated.
Wire
Signal Arm
• If your refrigerator is not connected to a
water supply or the water supply is turned
off, turn Off the ice maker.
• If you need a large quantity of ice at one
time, it is best to get cubes directly from
the ice container.
• The following sounds are normal when the
ice maker is operating:
- Motor running
- Ice dropping into ice container
- Water valve opening or closing
- Ice loosening from tray
- Running water
Off On
• When dispensing ice, you will hear a
snapping or clicking sound when the ice
chute opens and closes.
Wire
Signal Arm
• Turn Off the ice maker when cleaning the
freezer and during vacations.
- If you turn Off the ice maker for a
long period of time, you should also
turn off the water supply valve.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE & WATER DISPENSER
CAUTION
IMPORTANT
Chemicals from a malfunctioning water
softener can damage the ice maker. If the
water supply to your refrigerator is softened,
be sure the softener is maintained to work
properly.
When removing or replacing the ice bin,
DO NOT rotate the auger in the ice bin.
If the auger is accidentally rotated, you
must realign the auger by turning it in 90
degree turns (see below) until the ice bin
fits into place with the drive mechanism. If
the auger is not properly aligned when
replacing the ice bin, the refrigerator will
only dispense Crushed Ice. The freezer door
may also not close properly causing warm
air to leak into the freezer.
Cleaning the Ice Maker
Clean the ice maker and ice bin at regular
intervals, particularly before you take a
vacation or move.
To clean the ice maker:
1 Turn Off the ice maker.
2 Remove the ice bin by lifting up and out.
3 Empty and carefully clean the ice bin with
mild detergent. Rinse with clear water. Do
not use harsh or abrasive cleaners.
4 Allow the ice bin to dry completely before
replacing in the freezer.
5 Remove ice chips and clean the ice bin
shelf and the freezer door chute.
6 Replace the ice bin. Turn On the ice maker
to resume ice production.
Auger
Remove and empty the ice storage bin if:
• An extended power failure (one hour or
longer) causes ice cubes in the ice storage
bin to melt and freeze together, jamming
the dispenser mechanism.
• You do not use the ice dispenser frequently.
Ice cubes will freeze together in the bin,
jamming the dispenser mechanism.
Remove the ice storage bin and shake to
loosen the cubes or clean as explained above.
CAUTION
NEVER use an ice pick or similar sharp
instrument to break up the ice. This could
damage the ice storage bin and dispenser
mechanism.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE FILTER
If your refrigerator has not been used for a
period of time (during moving for example),
change the filter before reinstalling the
refrigerator.
Locating the Filter
Your refrigerator is equipped with a water
filtering system. The water filter system filters
all dispensed drinking water, as well as the
water used to produce ice.
Filter Cartridge
Air Filter (some models)
The air filter is located at the top of the fresh
food compartment next to the water filter.
Replacing the Air Filter
In general, you should change the air filter
every six months (the filter status light on the
control panel prompts you to replace the filter
after six months) to ensure optimal filtering
of refrigerator odors. You may want to adjust
this time period depending on the types and
amounts of food you typically store in your
refrigerator. To replace your PureSource
UltraTM air filter:
NOTE
If your refrigerator is equipped with a
PureSource 3TM water filter, it can be
replaced with a PureSource UltraTM water
filter. Replacing your PureSource 3TM water
filter with a PureSource UltraTM water
filter removes more potential contaminants
as tested by NSF. The contaminants or other
substances removed or reduced by this
water filter are not necessarily in all users’
water.
1
2
3
Pull the air filter housing straight out.
Remove the old filter and discard it.
Unpack the new filter and place it inside
the housing.
4 Slide the housing back into position.
Air Filter
Ordering Replacement Filters
To order your replacement filters, please visit
by calling toll-free at 877-808-4195, or by
visiting the dealer where you purchased your
refrigerator. Frigidaire recommends that you
order extra filters when you first install your
refrigerator, and that you replace your filters at
least once every six months.
Here are the product numbers to request when
ordering:
PureSource UltraTM Water Filter
Part# ULTRAWF
Water Filter
The water filter is located at the top right side
PureSource 3TM Water Filter
Part #WF3CB
of the fresh food compartment.
Replacing the Water Filter
NOTE
In general, you should change the water
filter every six months to ensure the highest
possible water quality. Water Filter Status on
the user interface prompts you to replace the
filter after a standard amount of water (200
gallons/757 liters for PureSource UltraTM
and PureSource 3TM) has flowed through the
system.
If your refrigerator is equipped with a
PureSource UltraTM water filter, it must be
replaced with PureSource UltraTM water
filter ULTRAWF.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE FILTER
5
Push firmly until the cartridge snaps into
place (you should hear a click as the
cartridge engages the snap-in connector).
More about your Advanced
Water Filter
The PureSource UltraTM ice and
water filter system is tested and
certified to NSF/ANSI Standards
42 and 53 for the reduction
of claims specified on the
6 Press a drinking glass against the water
dispenser while checking for any leaks at
the filter housing. Any spurts and sputters
that occur as the system purges air out of
the dispenser system are normal.
performance data sheet.
7
After filling one glass of water, continue
flushing the system for about four
minutes.
The PureSource 3TM ice and
water filter system is tested and
certified to NSF/ANSI Standards
42 and 53 for the reduction
of claims specified on the
8 Turn On the ice maker.
9 Press and hold the Water Filter button
on the Ice & Water Dispenser control
panel for three seconds. When the display
changes from “Red” to “Green,” the status
has been reset.
performance data sheet.
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may be
used on disinfected waters that may contain
filterable cysts.
Test & certification results:
• Rated Capacity - 200 gallons/757 liters for
PureSource UltraTM and PureSource 3TM
ice and water filter
• Rated service flow - .50 gallons per minute
• Operating Temp.: Min. 33°F, Max. 100°F
• Maximum Rated Pressure - 100 pounds per
square inch
• Recommended Minimum Operating
Pressure: 30 pounds per square inch
To replace your PureSource 3TM
water filter:
It is not necessary to turn the water supply off
to change the filter. Be ready to wipe up any
small amounts of water released during the
filter replacement.
1 Turn Off the ice maker.
2
3
4
Remove the filter by pushing on the end/
face of the filter.
Slide the old water filter cartridge straight
out of the housing and discard it.
Unpackage the new filter cartridge. Using
the alignment guide, slide it gently into
the filter housing until it stops against
the snap-in connector at the back of the
housing.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NORMAL OPERATING SOUNDS AND SIGHTS
Understanding the Sounds you
may Hear
Your new, high-efficiency refrigerator may
introduce unfamiliar sounds. These sounds
normally indicate your refrigerator is operating
correctly. Some surfaces on floors, walls, and
kitchen cabinets may make these sounds more
noticeable.
NOTE
Energy efficient foam in your refrigerator is
not a sound insulator.
NOTE
Following is a list of major components in your
refrigerator and the sounds they can cause:
During automatic defrost cycle, a red glow
in the back wall vents of your freezer
compartment is normal.
A Evaporator Refrigerant through the
evaporator may create a boiling or
gurgling sound.
B Evaporator fan You may hear air being
forced through the refrigerator by the
evaporator fan.
C Defrost heater During defrost cycles,
water dripping onto the defrost heater
may cause a hissing or sizzling sound.
After defrosting, a popping sound may
occur.
D
OR
D Automatic ice maker When ice has
been produced, you will hear ice cubes
falling into the ice bin.
E Electronic control & automatic
defrost control These parts can produce
a snapping or clicking sound when turning
the cooling system on and off.
F Condenser fan You may hear air being
forced through the condenser.
G Compressor Modern, high-efficiency
compressors run much faster than in the
past. The compressor may have a high-
pitched hum or pulsating sound.
H Water valve Makes a buzzing sound each
time it opens to fill the ice maker.
I Drain pan (not removable) You may hear
water dripping into the drain pan during
the defrost cycle.
J Condenser May create minimal sounds
from forced air.
K Motorized damper May produce a light
humming during operation.
L Ice chute When dispensing ice, you will
hear a snapping or clicking sound when
the solenoid opens and closes the ice
chute.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & CLEANING
Protecting your investment
Keeping your refrigerator clean maintains appearance and prevents odor build-up. Wipe up any
spills immediately and clean the freezer and fresh food compartments at least twice a year.
When cleaning, take the following precautions:
• Never use CHLORIDE or cleaners with bleach to clean stainless steel.
• Do not wash any removable parts in a dishwasher.
• Always unplug the electrical power cord from the wall outlet before cleaning.
• Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which
can scratch the appliance surface.
• Do not remove the serial plate.
Do not use abrasive cleaners such as window sprays, scouring cleansers, brushes, flammable
fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum
products on plastic parts, interior doors, gaskets or cabinet liners. Do not use paper towels,
metallic scouring pads, or other abrasive cleaning materials or strong alkaline solutions.
NOTE
If you set your temperature controls to turn off cooling, power to lights and other electrical
components will continue until you unplug the power cord from the wall outlet.
CAUTION
• Pull the refrigerator straight out to move it. Shifting it from side to side may damage
flooring. Be careful not to move the refrigerator beyond the plumbing connections.
• Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or
damp hands.
IMPORTANT
If you store or move your refrigerator in freezing temperatures, be sure to completely drain
the water supply system. Failure to do so could result in water leaks when the refrigerator is
put back into service. Contact a service representative to perform this operation.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & CLEANING
Care & Cleaning Tips
Part
What To Use
Tips and Precautions
Interior & Door
Liners
• Soap and water
Use two tablespoons of baking soda in
one quart of warm water. Be sure to
wring excess water out of sponge or
cloth before cleaning around controls,
light bulb or any electrical part.
• Baking soda and water
Door Gaskets
• Soap and water
• Soap and water
Wipe gaskets with a clean soft cloth.
Drawers & Bins
Use a soft cloth to clean drawer runners
and tracks.
Glass Shelves
Toe Grille
• Soap and water
• Glass cleaner
Allow glass to warm to room temperature
before immersing in warm water.
• Mild liquid sprays
• Soap and water
Vacuum dust from front of toe grille.
Remove toe grille (see Installation
Instructions). Vacuum backside, wipe with
sudsy cloth or sponge. Rinse and dry.
• Mild liquid sprays
• Vacuum attachment
Exterior &
Handles
• Soap and water
Do not use commercial household
cleaners containing ammonia, bleach or
alcohol to clean handles. Use a soft cloth
to clean smooth handles. DO NOT use a
dry cloth to clean smooth doors.
• Non Abrasive Glass
Cleaner
Exterior &
Handles
• Soap and water
Never use CHLORIDE or cleaners
with bleach to clean stainless steel.
• Stainless Steel Cleaners
(Stainless Steel
Models Only)
Clean stainless steel front and handles
with non-abrasive soapy water and a
dishcloth. Rinse with clean water and a
soft cloth. Use a non-abrasive stainless
steel cleaner. These cleaners can be
purchased at most home improvement or
major department stores. Always follow
manufacturer’s instructions. Do not use
household cleaners containing ammonia
or bleach.
NOTE: Always clean, wipe and dry
with the grain to prevent scratching.
Wash the rest of the cabinet with warm
water and mild liquid detergent. Rinse
well, and wipe dry with a clean soft cloth.
Replacing Light
Bulbs
• Unplug refrigerator
• Wear gloves
CAUTION: Wear gloves when
replacing light bulbs to avoid getting
cut.
• Remove light cover
• Replace old bulb
• Replace light cover
• Plug in the refrigerator
Use same wattage when replacing bulb.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU CALL
1-800-944-9044 (United States)
1-800-265-8352 (Canada)
Visit our web site at
CONCERN
CAUSE
SOLUTION
AUTOMATIC ICE MAKER
Ice maker is
not making any
ice.
• Ice maker wire signal arm is • Move wire signal arm to the “down” or
in the “up” or OFF position.
• Ice maker power switch
is Off.
ON position (side mounted).
• Turn power switch to On (“I”) position
(rear mounted).
• Ice maker has small cube • Remove small cube from ice maker. The
caught in mechanism.
ice and water filter cartridge may be
clogged. Replace filter cartridge.
• Saddle valve on cold
water pipe is clogged
or restricted by foreign
material.
• Turn off household water line valve.
Remove valve. Ensure that valve is not
a self-piercing saddle valve. Clean valve.
Replace valve if necessary.
Ice maker is
not making
enough ice.
• Ice maker is producing
• Side mounted ice maker should produce
4 to 4.5 pounds (approximately 4 quarts)
of ice every 24 hours. A rear mounted
ice maker should produce 3 to 4 pounds
(approximately 3½ quarts) of ice every 24
hours. Quick Ice option should produce
up to 50% more ice every 24 hours.
• If it is, replace the ice and water filter
cartridge.
less ice than you expect.
• Check to see if water
dispenser is dispensing
slower than normal.
• Freezer control is set too • Set freezer control to colder setting to im-
warm.
prove performance of the ice maker. Allow
24 hours for temperature to stabilize.
Ice maker will
not stop mak-
ing ice.
• Ice maker wire signal arm • Move item and release wire signal arm.
is being held down by
Remove any ice cubes that are frozen
together over the wire signal arm.
some item in the freezer.
Ice cubes are
freezing to-
gether.
• Ice cubes are not being
used frequently enough.
• Ice cubes are hollow
(partially frozen cubes
with water inside).
• Remove ice container and discard ice from
container. Ice maker will produce fresh supply.
• The ice and water filter cartridge may be
clogged. Replace filter cartridge.
• Freezer control is set too • Set freezer control to colder setting. Allow
warm.
DISPENSER (Ice & Water)
24 hours for temperature to stabilize.
Dispenser will
not dispense
ice.
• Dispenser lock out is
engaged.
• Press and hold control lock for three
seconds.
• There is no ice in the bin • See the “Ice maker is not making any ice”
to be dispensed.
section above.
• The refrigerator doors are • Be sure the refrigerator doors are
not completely closed.
• Dispenser paddle has
been pressed too long
and the dispenser motor
has overheated.
completely closed.
• The motor overload protector will reset in
about three minutes and then ice can be
dispensed.
Ice dispenser is • Ice has melted and
• Remove ice container, thaw, and empty
the contents. Clean container, wipe dry,
and replace in proper position. When new
ice is made, dispenser should operate.
jammed.
frozen around auger
due to infrequent use,
temperature fluctuations,
and/or power outages.
• Ice cubes are jammed
between ice maker and
back of ice container.
• Remove ice cubes that are jamming the
dispenser.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU CALL
CONCERN
CAUSE
SOLUTION
DISPENSER (Ice & Water) (Continued)
Dispenser will
not dispense
water.
• Dispenser lock out is
engaged.
• Water filter not seated
properly.
• Press and hold control lock for three
seconds.
• Remove and reinstall the water filter. Be
sure to push the filter firmly so that you
hear it lock solidly into position.
• Replace filter cartridge. Be sure to remove
protective caps and push the filter firmly so
that you hear it lock solidly into position.
• Open household water line valve. See CON-
CERN column AUTOMATIC ICE MAKER.
• Water filter is clogged.
• Household water line
valve is not open.
Water has an
odd taste and/
or odor.
• Water has not been dis-
pensed for an extended
period of time.
• Unit not properly con-
nected to cold water line.
• Draw and discard 10-12 glasses of water
to freshen the supply.
• Connect unit to cold water line that
supplies water to the kitchen faucet.
Water pressure • Cut-off and cut-on
• Have someone turn up the cut-off and
cut-on pressure on the water pump
system (well systems only).
is extremely
low.
pressures are too low
(well systems only).
• Reverse osmosis system
is in regenerative phase.
• It is normal for a reverse osmosis system
to be below 20 psi during the regenerative
phase.
Water not cold
enough.
• As warmer tap water goes • Add ice to cup or container before
through the filter and
enters the water tank the
chilled water is pushed
through to the dispenser.
Once the chilled water is
used up it will take several
hours to bring the freshly
replaced water to a cooler
temperature.
dispensing water.
OPENING/CLOSING OF DOORS/DRAWERS
Door(s) will not • Door was closed too
• Close both doors gently.
close.
hard, causing other door
to open slightly.
• Refrigerator is not level.
It rocks on the floor
when moved slightly.
• Refrigerator is touching a
wall or cabinet.
• Ensure floor is level and solid, and can
adequately support the refrigerator.
Contact a carpenter to correct a sagging
or sloping floor.
• Ensure floor is level and solid, and can
adequately support the refrigerator.
Contact a carpenter to correct a sagging
or sloping floor.
Drawers are
difficult to
move.
• Food is touching shelf on • Remove top layer of items in drawer.
top of drawer.
• Track that drawers slide
• Ensure drawer is properly installed on
track.
on is dirty.
• Clean drawer, rollers, and track. See Care
& Cleaning.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU CALL
CONCERN
CAUSE
SOLUTION
RUNNING OF REFRIGERATOR
Compressor
does not run.
• Freezer control is set to
“OF” or “0”.
• Set freezer control.
• Refrigerator is in defrost • This is normal for a fully automatic defrost
cycle.
refrigerator. The defrost cycle occurs
periodically, lasting about 30 minutes.
• Ensure plug is tightly pushed into outlet.
• Plug at electrical outlet
is disconnected.
• House fuse blown or
tripped circuit breaker.
• Power outage.
• Check/replace fuse with a 15 amp
time-delay fuse. Reset circuit breaker.
• Check house lights. Call local electric company.
Refrigerator
runs too much
or too long.
• Room or outside
weather is hot.
• Doors are opened too
frequently or too long.
• Fresh Food/freezer door • Ensure refrigerator is level. Keep food and con-
may be slightly open.
• It’s normal for the refrigerator to work
longer under these conditions.
• Warm air entering the refrigerator causes
it to run more. Open doors less often.
tains from blocking door. See PROBLEM column
OPENING/CLOSING OF DOORS/DRAWERS.
• Set Fresh Food control to warmer setting
until refrigerator temperature is satisfactory.
Allow 24 hours for temperature to stabilize.
• Clean or change gasket. Leaks in door
seal will cause refrigerator to run longer in
order to maintain desired temperatures.
• Clean condenser. See Care & Cleaning.
• Freezer control is set
too cold.
• Fresh Food/freezer
gasket is dirty, worn,
cracked, or poorly fitted.
• Condenser is dirty.
Compressor
goes off and on
frequently.
• Thermostat keeps the
refrigerator at a
constant temperature.
• This is normal. Refrigerator goes on and
off to keep temperature constant.
DIGITAL TEMPERATURE DISPLAY
Digital temper- • Electronic control system • Call your Frigidaire service representative,
ature displays
are flashing.
has detected a
performance problem.
who can interpret any messages or num-
ber codes flashing on the digital displays.
WATER/MOISTURE/FROST INSIDE REFRIGERATOR
Moisture col-
lects on inside
of refrigerator
walls.
• Weather is hot and
humid.
• Door is slightly open.
• The rate of frost buildup and internal
sweating increases.
• See PROBLEM column OPENING/CLOSING
OF DOORS/DRAWERS.
Water collects
on bottom
side of drawer
cover.
• Vegetables contain and
give off moisture.
• It is not unusual to have moisture on the
bottom side of the cover.
• Move humidity control (some models) to
lower setting.
Water collects
in bottom of
drawer.
• Washed vegetables and
fruit drain while in the
drawer.
• Dry items before putting them in the
drawer. Water collecting in bottom of
drawer is normal.
WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR
Moisture col-
lects on outside
of refrigerator
or between
doors.
• Weather is humid.
• This is normal in humid weather. When
humidity is lower, the moisture should
disappear.
• See PROBLEM column OPENING/CLOSING
OF DOORS/DRAWERS.
• Door is slightly open,
causing cold air from in-
side refrigerator to meet
warm air from outside.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MAJOR APPLIANCE WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained
in accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside
the USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other
consumables, or knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry
trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not
limited to floors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE
YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH
AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS
WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty
period should service be required. If service is performed, it is in your best interest to obtain and
keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the
addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted
by Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In
Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to
change or add to any obligations under this warranty. Obligations for service and parts under this
warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USA
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
1.800.944.9044
Frigidaire
10200 David Taylor Drive
Charlotte, NC 28262
27
Download from Www.Somanuals.com. All Manuals Search And Download.
|