DO NOT REMOVE this label until the refrigerator has been leveled.
Please follow all instructions for leveling your refrigerator.
Installation Instructions* for French Door Bottom Freezer/Refrigerator
®
*Please refer to your Use & Care Guide for more details.
To Connect Water Supply Line To Ice Maker Inlet Valve:
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or
bucket. Turn ON water supply and flush
Doors final adjustment using the adjustable lower hinge (select models, if
necessary):
WARNING
1 Open doors to 90 degrees.
2 Remove screw.
To avoid electric shock, which can cause death or severe personal injury,
do not connect your refrigerator to an electrical power source until you
have completed Step 2 of these instructions.
Steel
3
Lift the door while adjusting the washer.
supply line until water is clear. Turn OFF
water supply at shutoff valve.
3. Remove plastic cap from water valve inlet
and discard cap.
Clamp
Plastic Water
Tubing to
To raise the door: rotate washer clockwise.
To lower the door: rotate washer counterclockwise.
Brass
Compression
Nut
Filter
4 Replace the screw, ensuring it is between the spokes of the hinge washer. Screw will not
be tight, just insert until it is flush with the hinge.
NOTE
4. If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve) onto
water supply line. Push water supply line into
water valve inlet as far as it will go (¼ inch).
Slide ferrule (sleeve) into valve inlet and
finger tighten compression nut onto valve.
Tighten another half turn with a wrench; DO
NOT overtighten. See Figure 1.
If you use stainless steel tubing - The nut
and ferrule are already assembled on the
tubing. Slide compression nut onto valve
inlet and finger tighten compression nut
onto valve. Tighten another half turn with a
wrench; DO NOT overtighten. See Figure 2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel
of refrigerator as shown.
6. Coil excess water supply line (copper tubing
only), about 2½ turns, behind refrigerator
as shown and arrange coils so they do not
vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and
tighten any connections that leak.
8. Reconnect refrigerator to electrical power
source.
9. To turn ice maker on, lower wire signal arm
(freezer ice maker) or set the ice maker’s On/
Off power switch to the “ON” position (fresh
food ice maker).
Ferrule
Loosen or Remove
B
(Sleeve)
Screw
If you need to remove the doors to get your refrigerator into the house, please refer to
“Removing Doors” in the Use & Care Guide. These installation instructions are provided only as
a possible customer option. Frigidaire recommends that you use a service or kitchen contracting
professional to install your refrigerator.
NOTE
Copper
water line
If after adjusting doors higher the
door makes a popping/clicking sound,
remove screw and replace with the
longer one provided.
Open
A
Door
90
degrees
Water Valve
Bracket
IMPORTANT
If you are installing your refrigerator
without connecting it to a water
supply, make sure the ice maker’s
power switch is turned Off (see the
Use & Care Guide for more details).
CAUTION
Valve Inlet
Bottom of Door
Water Valve
• Shifting the refrigerator from side to side
Raising/Lowering Door
may damage flooring.
Remove Screw
• Do not block the toe grille on the lower
front of your refrigerator. Sufficient air cir-
culation is essential for proper operation.
Copper water line
from household water supply
Leveling Freezer Drawer (if necessary)
4
Preparing For Installation
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
1
Remove Hex
Head Drawer
Screw
Remove Hex
Head Drawer
Screw
NOTE
Be sure to coordinate site preparation and installation
Figure 1
Do Not Remove
Other Screws
Do Not Remove
Other Screws
with your kitchen contractor.
NOTE
Include these minimum guidelines in your site preparation:
DO NOT remove center screw from freezer
drawer. This is a factory adjustment.
•
•
•
Choose a place near a grounded electrical outlet.
Do not use an extension cord or an adapter plug.
Avoid direct sunlight and close proximity to a range,
dishwasher or other heat source.
Floor should be level and able to
support a fully loaded refrigerator.
The refrigerator’s Ice Dispenser
requires water supply access.
Please call 1-800-944-9044 if you
Plastic Water
Tubing
to Filter
Remove Hex
Head Drawer
Screw
Remove Hex
Head Drawer
Screw
need assistance with this installation.
1. Check gasket seal around top, bottom,
and sides of freezer drawer.
2. If gasket is not sealed, open drawer
and slightly loosen 4 drawer screws
(2 on each side) to allow drawer to
rotate.
3. Close drawer and recheck the seal
on the gasket (A). Open the drawer
grabbing by the sides in the center
(B). Be careful not to rotate the
drawer.
•
•
•
•
CAUTION
Plan for easy access to counter tops
when removing food.
Grab Drawer
At Center
From Both Sides
Then
Pull Drawer Out
Room temperatures
below 55°F (13°C)
or above 110°F
For complete access to drawers and
freezer baskets, doors must be able to
fully open.
Push Against
Freezer Drawer
(43°C) will impair
cooling ability of
your refrigerator’s
NOTE
•
Load refrigerator from side of cabinet
only.
•
•
Do not run retaining straps over handles nor overtighten straps.
Never use refrigerator handles to move the refrigerator.
compressor.
Check with your local building authority for
recommendations on water lines and associated
materials prior to installing your new refrigerator.
Depending on your local/state building codes,
Frigidaire recommends for homes with existing
valves its Smart Choice® water line kit
4. Tighten 4 drawer screws.
5. Recheck gasket seal.
Allow the following clearances for ease of installation, proper air
circulation, and plumbing and electrical connections: Sides & Top: 3/8 inch / Rear: 1 inch
6. Install the toe grille by fitting into
A
place.
B
Connect Water Supply
2
5305513409 (with a 6 ft. Stainless Steel Water
Line) and for homes without an existing valve,
Frigidaire recommends its Smart Choice water®
line kit 5305510264 (with a 20 ft. Copper Water
Line with self-tapping saddle valve). Please refer
Remove Internal Shipping Materials
Frigidaire uses packing foam and tape to secure the internal parts of your refrigerator for
shipping. Once the refrigerator is in position, you can remove this material.
5
Before Installing The Water Supply Line, You Will Need:
•
•
•
Basic Tools: adjustable wrench, flat-blade screwdriver, and
PhillipsTM screwdriver
WARNING
Access to a household cold water line with water pressure
between 30 and 100 psi.
Figure 2
What’s Next?
To avoid electric shock,
which can cause death
or severe personal
A water supply line made of ¼ inch (6 mm) OD, copper
or stainless steel tubing. To determine the length of tubing
needed, measure the distance from the ice maker inlet
valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet, so the refrigerator
can be moved out for cleaning.
Congratulations! You are ready to begin enjoying your new Frigidaire refrigerator.
•
•
•
For important safety instructions and to learn how to operate your refrigerator, please read
the entire Use & Care Guide.
You may want to start with the “Normal Operating Sights & Sounds” section of the Guide to
learn what to expect during typical operation.
simply send in the Registration Card.
injury, disconnect the
refrigerator from elec-
trical power before con-
necting a water supply
line to the refrigerator.
Level Refrigerator & Adjust Doors (if necessary)
3
•
•
•
Guidelines for final positioning of your refrigerator
•
•
A shutoff valve to connect the water supply line to your
household water system. DO NOT use a self-piercing type
shutoff valve.
All four corners of the cabinet must rest firmly on the
floor.
The sides should tilt ¼ inch (6 mm) from front to
back (to ensure that doors close and seal properly).
Doors should align with each other and be level.
A compression nut and ferrule (sleeve) for connecting a
copper water supply line to the ice maker inlet valve.
Installation Check List
Doors
6
Door
Ice Maker
Door
Most of these conditions can be met by raising or
lowering the adjustable front rollers.
CAUTION
To Avoid Property Damage:
□ Handles are secure and tight
□ Door seals completely to cabinet on all sides
□ Fresh food doors are level
Leveling
□ Refrigerator is level, side to side and tilted
¼ inch (6 mm) front to back
□ Toe grille is properly attached to refrigerator
□ Cabinet is sitting solid on all corners
Electrical Power
□ House water supply connected to
refrigerator
To level the cabinet using the front rollers:
□ No water leaks present at all connections
□ Ice Maker is turned ON.
• Copper or Stainless Steel braided tubing is recommended for the wa-
ter supply line. Water supply tubing made of ¼ inch (6 mm) plastic is
not recommended to be used. Plastic tubing greatly increases the po-
tential for water leaks, and the manufacturer will not be responsible
for any damage if plastic tubing is used for the supply line.
• Do not reuse compression fitting or use thread seal tape.
• DO NOT install water supply tubing in areas where temperatures fall
below freezing.
1 You can raise or lower each door. Use a 3/8 inch socket
wrench to turn the adjustment screws (1 per side).
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw counterclockwise.
2 Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that cabinet
is stable.
Final Checks
Raise
□ Shipping material removed
Anti-tip
Leg
□ Fresh Food and Freezer temperatures set
Lower
• Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure that the softener is
maintained and working properly.
3
After unit is leveled, lower anti-tip leg until it contacts
the floor.
□ House power turned on
□ Refrigerator plugged in
If you are not satisfied with the installation of your refrigerator, please contact the store where you purchased it or call 1-800-944-9044 for assistance.
P/N: 242046901
Download from Www.Somanuals.com. All Manuals Search And Download.
|