Frigidaire Ice Maker IM115 User Manual

ICE MAKER  
INSTALLATION  
INSTRUCTIONS  
To avoid electric shock, which can cause death or severe personal injury,  
disconnect the refrigerator from electrical power before connecting a water supply line to  
the refrigerator.  
To Avoid Property Damage:  
• Copper tubing is recommended for the water supply line. Water supply tubing made of 1/4”  
plastic is not recommended since it greatly increases the potential for water leaks.  
The manufacturer will not be responsible for any damage if plastic tubing is used for the  
supply line.  
DO NOT install water supply tubing in areas where temperatures fall below freezing.  
• Connect the ice maker to a drinkable water source that is not tied into a water softening  
system. Chemicals from the softener may damage the ice maker, causing it to  
malfunction.  
The following items will be required to install the ice maker kit.  
1/4 inch copper supply line with shut off valve  
1/4 inch brass compression nut and ferrule  
Freezer shelf (Some models not eqipped with shelf). If your  
model does not have one, contact your dealer to order one.  
The copper tubing and shut off valve are available in a kit from your  
local hardware or plumbing supply store. Coil enough tubing at the  
back of the unit to allow movement for cleaning.  
P/N 240394901  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Unplug refrigerator from wall outlet.  
6. Peel off label covering ice maker hole.  
2. Remove ice tray rack from freezer (some models).  
3. Remove freezer shelf (some models) by pushing shelf  
to left until right side of shelf is out of hole. Slowly lift  
up and pull on shelf to remove.  
4. Remove plugs from inside freezer compartment  
with putty knife.  
7. With needle nose pliers, remove foam from hole.  
5. If refrigerator has exterior condenser (C), go to rear of  
refrigerator and locate left condenser mounting bracket  
screw(s). Remove and save screws. DO NOT remove  
compressor sound baffle (A), if installed.Carefully bend  
condenser out away from back of refrigerator.  
If condenser is mounted inside compressor  
compartment (D), remove screws securing  
sound baffle to cabinet (B).  
8. Push water inlet tube into small hole on back of  
refrigerator. Rotate while inserting tube until flat  
surface of inlet tube is tight against back of  
refrigerator.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Push plastic water supply tubing (3) into water inlet 12. With ice maker in one hand, plug ice maker  
tube (11) as far as it will go and finger tighten nylon  
compression nut onto threaded end of inlet tube.  
Tighten another one half turn with a wrench. DO NOT  
over tighten.  
connector into connector mounted on back freezer  
panel. Make sure connection is tight.  
13. Mount ice maker onto two screws (5) you installed  
in Step 12.Tighten screws. Make sure water inlet  
tube (11) is sitting inside fill cup.  
10. Install adjustable leveling bracket (7) on bottom of  
ice maker with screw (6). DO NOT tighten bracket.  
(Bracket will be tightened later.)  
14. Adjust leveling bracket (7) to level ice maker (1). Ice  
maker is level when gap between freezer wall and  
ice maker is same at top and bottom. Tighten screw  
(6) when level.  
11. Start two, long, ice maker mounting screws (5) into  
freezer wall. Turn each screw five turns clockwise.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
15. Reinstall freezer shelf in lower position. Set ice  
container (2) on shelf.  
18. Push plastic water supply tubing into bottom of water  
valve as far as it will go. Finger tighten nylon  
compression nut onto threaded end of water valve.  
Tighten another one half turn with wrench. DO NOT  
overtighten.  
19. Secure plastic water tubing to rear of cabinet with  
two plastic clamps (9).  
16. Locate factory punched holes at bottom right corner  
of rear panel. Holes are only drilled through cabinet  
liner. Align water valve bracket with factory drilled  
holes. Use a power drill with a Phillips® head bit to  
drive the two self drilling screws (4) through bracket  
and into cabinet.  
NOTE: Clean back of cabinet with a commercial  
household cleaner, ammonia or alcohol before  
applying clamps.  
20. On models with exterior condenser, reinstall  
condenser brackets and tighten down screws.  
17. Connect wiring harness to water valve. Make sure  
connection is tight.  
21. On refrigerators with dynamic condensers, remount  
sound baffle, if installed. See step 5.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Ice Maker to Water Supply  
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator  
from electrical power before connecting a water supply line to the refrigerator.  
To Avoid Property Damage:  
• Copper tubing is recommended for the water supply line. Water supply tubing made of 1/4 inch plastic is not  
recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible for any  
damage if plastic tubing is used for supply line.  
DO NOT install water supply tubing in areas where temperatures fall below freezing.  
• Connect the ice maker to a potable water source that is not tied into a water softening system. Chemicals from the  
softener may damage the ice maker, causing it to malfunction.  
IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.  
Before Installing The Water Supply Line, You Will Need  
Basic tools: adjustable wrench, flat blade screwdriver, and PhillipsTM screwdriver.  
• Access to a household cold water line with water pressure between 20 and 120 psi.  
• A water supply line made of 1/4 inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing  
needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your  
cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning.  
• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type  
shutoffvalve.  
• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.  
NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25  
feet (7.6 meters) of 1/4 inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) 1/4 inch brass  
compression nuts, (2) ferrules/sleeves, and instructions for installing a water supply line.  
To Connect Water Supply Line To Ice Maker Inlet Valve  
1. Disconnect refrigerator from electric power supply.  
2. Place end of water supply line into sink or bucket. Turn ON water  
supply and flush supply line until water is clear. Turn OFF water  
supply at shutoff valve.  
3. Unscrew plastic cap from water valve inlet and discard cap.  
4. Slide brass compression nut, then ferrule (sleeve), onto water supply  
line, as shown.  
5. Push water supply line into water valve inlet as far as it will go (1/4  
inch). Slide ferrule (sleeve) into valve inlet and finger tighten  
compression nut onto valve.Tighten another half turn with a wrench;  
DO NOT over tighten.  
6. With steel clamp and screw, secure water supply line to rear panel  
of refrigerator at location as shown.  
7. Coil excess water supply line (about 2-1/2 turns) behind  
refrigerator as shown and arrange coils so they do not vibrate or  
wear against any other surface.  
8. Turn ON water supply at shutoff valve and tighten any  
connections that leak.  
9. Reconnect refrigerator to electric power supply.  
10.To turn ice maker on, lower wire signal arm. (See ice maker front cover for on/off position of arm.)  
IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing  
lines may cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause  
ice to be discolored or have poor flavor. Discard ice made during the first 24 hours.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Automatic Ice Maker Tips  
Remember that water quality determines your ice quality. Do not connect  
the ice maker to water that is softened. Chemicals from a malfunctioning  
softener can damage the ice maker.  
To stop the ice maker, lift the wire signal arm until it clicks and locks in the  
“up” or OFF position. The ice maker turns off automatically when the ice  
container is full. If your model has an adjustable freezer shelf, place the  
shelf so the wire signal arm will hit the ice when the ice container is full.  
Ice Maker Tips  
Ice stored too long may develop an odd flavor. Empty the container and be sure the wire signal arm is in its  
“down” or ON position. The ice maker will then produce more ice.  
Occasionally shake the container to keep ice separated.  
Keep the wire signal arm in its “up” or OFF position until the refrigerator is connected to the water supply or  
whenever the water supply is turned off.  
The following sounds are normal when the ice maker is operating.  
Motor running  
Ice loosening from tray  
Ice dropping into ice container  
Running water  
Water valve opening or closing  
DO NOT place the ice container in your dishwasher.  
Wash ice container in warm water with mild detergent. Rinse well and dry.  
Stop the ice maker when cleaning the freezer or for short vacations.  
If the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  

Euro Pro Convection Oven JO287SP User Manual
Euro Pro Vacuum Cleaner XSC410 User Manual
Fellowes Paper Shredder PS 10Cs User Manual
Frigidaire Dishwasher F71C12 User Manual
Gateway Personal Computer FX530XG User Manual
Geemarc Telephone AMPLI500 User Manual
Gefen TV Cables EXT HDMI13 1410 BLK User Manual
GE Griddle 169148 User Manual
Gianni Industries Door GL600 S User Manual
Giant Water Pump P220 3000 User Manual