PumpAssembly
ProductSpecifications
Electrical
Trouble Shooting Tips
Water Supply
The drain hose must have a loop at a minimum
height of 32 inches in order to insure proper
drainage.
The pump assembly is driven by a synchronous
motor. The motor drives a pump which supplies
100 percent filtered water
Suggested minimum incoming water
temperature ............................ 120°F (49°C)
Pressure (PSI) min./max. .................. 20/120
Connection (NPT) ..................................... 3/8
Consumption (Normal Cycle) ......................
.......................................... 5.2 - 5.6 U.S. gal
Water valve flow rate (U.S. GPM)............ 0.9
Water recirculation rate (U.S. GPM) ..............
................................................. approx. 5.28
Water fill time ................................... 36 sec.
Rating ...................................120 Volts, 60Hz
Separate Circuit..15 amp min.- 20 amp max.
Motor (Amps) ...................................0.6 - 0.9
Heater Wattage .......................... 475 - 630W
Total Amps (load rated) .......................... 7.0
TempAssure .............................. 135°F ±5°F
(60°C±3°C) [with outer door in place]
TempBoost ................................ 140°F ±5°F
Heated Wash/Heated Rinse
Hi-Limit Thermostat ............... 200°F (93°C)
Personal Injury Hazard
Draining is accomplished by using a small
separate synchronous drain pump mounted to
the side of the sump. The drain pump is
connected to the main pump by a small rubber
hose. The drain check valve is located at the
discharge end of the drain pump. The drain hose
is attached by a clamp to the discharge end of
the drain pump.
"
Always disconnect the dishwasher from the electrical power source before adjusting or
replacing components.
Check the Following
Remedy
Symptom
1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection
faulty.
1. Replace fuse or reset breaker.
2. Repair or replace wire fasteners at
dishwasher junction box.
Dishwasher will not operate when
turnedon.
3. Electronic control board defective.
4. No 12 VAC power to control.
5. Motor (inoperative).
6. Door switch (open contacts).
7. Door latch not making contact with
door switch.
8. Touch pad circuit defective.
9. No indicator lamps illuminate when
START or OPTIONS are pressed.
3. Replace control board.
4. Replace control board.
5. Replace motor/impeller assembly.
6. Replace latch assembly.
7. Replace latch assembly.
Heater
Refer to the cycle chart on the reverse side to
determine when the heater is on during the
wash cycle. The heater cycles ON and OFF for
brief periods during the drying cycle.
Voltage checks of the heater should be made in
the dry portion of the service test mode.
8. Replace console assembly.
9. Replace console assembly.
1. Motor (bad bearings).
2. Motor stuck due to prolonged
non-use.
1. Replace motor assembly.
2. Rotate motor impeller.
Motor hums but will not start or run.
Standard Dry Air Flow
The water on the dishes is evaporated into drier
air and the venting process continues. The
heatingelementisturnedONandOFFduringthe
entire drying cycle.
The heated, moist air leaving the dishwasher
through the console vent causes drier air to be
drawn into the unit by way of intake vents located
at the bottom of the door.
1. Improper voltage.
2. Motor windings shorted.
3. Glass or foreign items in pump.
1. Check voltage.
2. Replace motor/impeller assembly.
3. Clean and clear blockage.
Motor trips out on internal thermal
overloadprotector.
1. Heaterelement(open).
1. Replace heater element.
2. Replace control board.
3. Repair or replace.
Dishwasher runs but will not heat.
2. Electronic control board defective.
3. Wiring or terminal defective.
4. Hi-Limit thermostat defective.
DetergentandRinseAidDispenser
4. Replace thermostat.
The detergent and rinse aid dispenser is a one To replace dispenser:
1. Latch mechanism defective.
2. Electronic control board defective.
3. Wiring or terminal defective.
4. Broken spring(s).
1. Replace dispenser.
2. Replace control board.
3. Repair or replace.
4. Replace dispenser.
5. Replace dispenser.
Detergent cover will not latch or
open.
piece component consisting of a molded
detergent cup and a built-in rinse aid dispenser.
• shut off electricity to dishwasher,
• remove outer door panel assembly,
• disconnect wiring to the actuator,
• remove the six screws,
• remove the dispenser,
• replace and reinstall screws,
The detergent cup has a spring loaded cover
and the rinse aid dispenser has a removable
cover.
5. Defective actuator.
1. Drain restricted.
1. Clear restrictions.
2. Replace control board.
3. Replacepump.
4. Check for blockage, clear.
5. Replace pump assembly.
6. Repair or replace.
Dishwasherwillnotpumpout.
2. Electronic control board defective.
3. Defective drain pump.
4. Blocked impeller.
5. Open windings.
6. Wiring or terminal defective.
Liquid rinse aid is added to the dispenser up to • rewire actuator.
the fill line indicator. The amount of rinse aid
released can be adjusted by turning the arrow
indicator from one, being the least amount, to
four, being the greatest amount.
1. Water supply turned off.
2. Defective water inlet fill valve.
3. Check fill valve screen for
obstructions.
1. Turn water supply on.
2. Replace water inlet fill valve.
3. Disassemble and clean screen.
Dishwasher will not fill with water.
4. Defective float switch.
5. Electronic control board defective.
6. Wiring or terminal defective.
7. Pressure Switch Stuck.
4. Repair or replace.
5. Replace control board.
6. Repair or replace.
7. Repair or replace.
1. Drain hose (high) loop too low.
1. Repair to proper 32-inch minimum
height.
2. Install air gap at counter top.
Dishwasherwatersiphonsout.
Detergent left in dispenser.
2. Drain line connected to a floor drain
not vented.
1. Detergentallowedtostandtoolongin
dispenser.
2. Dispenser wet when detergent was
added.
1. Instruct customer/user.
2. Instruct customer/user.
3. Detergentcoverheldclosedorblocked
by large dishes.
3. Instruct customer/user on proper
loading of dishes.
4. Improper incoming water
temperature to properly dissolve
detergent.
4. Incoming water temperature of
120°F is required to properly
dissolve dishwashing detergents.
5. See "Detergent cover will not open."
020905
Download from Www.Somanuals.com. All Manuals Search And Download.
|