Foundations Baby Furniture 103 BQS User Manual

Model 103-BQS  
Wall Seat Installation Instructions  
Thank you for purchasing a quality Foundations® product. Our goal is 100% consumer satisfaction!  
If, for any reason you are not satisfied or if you have questions regarding your product or installation,  
please contact our customer service team at 1-877-716-2757. Please DO NOT contact your distributor  
or reseller as we are better prepared to assist you.  
WARNING  
Failure to follow these warnings and the installation instructions could result in serious injury  
or death.  
Read all instructions before installing wall seat. Keep these instructions. DO NOT discard.  
SI256E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
1. Locate area that can support the wall seat when mounted to the partition.  
Top  
2. Measure up 33” (84 cm) from the floor and mark the partition (Fig. a).  
This locates the position for the top left attachment hole.  
3. Align hole in top left corner of wall seat with mark on partition and hold in place.  
8"  
8 1/2”  
16-5/16"  
(203 mm)  
4. Using a level and measuring tape, mark the remaining three (3) holes. After  
marking holes, set wall seat down on ground.  
(216 mm)  
(414 mm)  
33”  
(84 cm)  
5. Use a power drill and 3/8” bit to drill four (4) holes through partition a mounting  
points.  
6. From opposite side of partition, insert four (4) T-nuts into mounting holes.  
7. Align holes in wall seat with drilled holes and secure top left corner of wall seat  
to partition using a machine screw and flat washer into the T-nuts. Continue to  
secure the three (3) remaining corners using the machine screws and flat  
washers into the T-nuts (Fig. b).  
Fig. a  
A. F. F  
Flat  
Washer  
Machine  
Screw  
Fig. b  
Wall Seat  
WARNING  
All 4 of these locations MUST be used for safe installation.  
8. Ensure all four (4) screws are tight and snap caps over screw heads.  
NOTE: Operate seat three (3) or four (4) times to ensure proper function.  
OPERATION:  
Rotate base downward. Place infant on top of the changing surface. Use restraint system as described below. After child has been  
changed, remove restraint system and rotate base back up against the wall.  
USE OF RESTRAINT SYSTEM:  
Place child on wall seat. Place restraint system over child shoulders and buckle between child’s legs. Insert buckle tongue into buckle  
and snap together. To tighten or loosen straps, slide adjuster up or down strap. To remove restraint system, press sides of buckle to  
release tongue and pull tongue out of buckle.  
MAINTENANCE AND CLEANING:  
Check all hardware and components monthly or as required to ensure hardware is tight and there are no missing or damaged  
components. Take unit out of service if any component is missing or damaged and contact customer service to order replacement  
parts. Do not substitute parts. For replacement parts, contact customer service at 1-877-716-2757.  
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong chemical cleaners or  
cleaning agents that may be hazardous to children.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edelbrock Automobile Parts 1580 User Manual
Edelbrock Automobile Parts 10220275 User Manual
Extron electronic Stereo Amplifier CVEQ 100 MAAP User Manual
Faber Ventilation Hood 5980410 User Manual
Fisher Price Motorized Toy Car B1501 User Manual
Freedom9 Network Card X10P User Manual
Gaggia Coffee Grinder 8002 User Manual
GE Dishwasher 165D4700P387 User Manual
Gianni Industries Switch BTS 400 ANSI User Manual
Global Machinery Company Air Compressor 40L User Manual