Fostex DVR D 160 User Manual

D-160 Owner's Manual (Introduction)

Owner's Manual

Model

Digital Multitrack Recorder

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Introduction)

Table of Contents

Introduction.......................................................................................6

Precautions.......................................................................................6

Notes about power supply.......................................................................6

Notes on handling the hard disk............................................................7

Notes on the setup location.....................................................................7

Notes on repair.........................................................................................8

About copyrights......................................................................................8

About damages.........................................................................................8

Notes on using the Detachable Controller.............................................8

How to use a dust cap (included)............................................................8

Main Features of D-160..........................................................................9

Names and Functions..........................................................................12

Front panel..............................................................................................13

Detachable controller............................................................................14

Rear panel...............................................................................................23

Display section.......................................................................................25

1. Display shown when the power is turned on....................................25

2. Preset display........................................................................................25

3. Switching the display using the DISP SEL key...................................26

4. Switching the Time Base display

using the EXECUTE/YES key and DISP SEL key...........................27

5. Changing Programs using the STORE key and

the HOLD/> key.............................................................................28

6. Warning messages................................................................................29

Before operating the D-160.................................................................32

1. Hard disk recording method and the REMAIN display..................32

2. Audio file and Event..........................................................................33

3. Program Change function.................................................................35

4. Real track and Additional track........................................................36

5. Input monitor and Repro monitor...................................................37

6. Time Base............................................................................................38

7. Installing and formatting a hard disk..............................................39

Installing a removable hard disk cartridge...........................................40

Replacing a removable hard disk cartridge..........................................41

Installing a hard disk in removable case Model 9040B........................42

Formatting a hard disk............................................................................43

8. Extending the detachable controller...............................................44

Recording/Playback............................................................................46

1.Basic connections................................................................................46

2. The default setting on the D-160.....................................................48

2-1. Setting a Program.............................................................................49

2-2. Program Change...............................................................................50

2-3. Deleting a Program...........................................................................51

2-4. Setting a Sampling Rate....................................................................52

3. Analog Recording and Playback.......................................................53

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Introduction)

3-1. Basic recording and playback.........................................................53

3-2. Recording with the Program Change function.............................54

3-3. Playback using the Vari-pitch function.........................................56

3-4. Multitrack recording using overdubbing......................................57

3-5. Mixdown............................................................................................58

3-6. Ping-pong recording........................................................................59

4. Digital Recording...............................................................................60

4-1. Digital recording from an external digital device (S/P DIF)........60

4-2. Digital recording to an external digital device .............................63

4-3. Connecting a digital mixer..............................................................65

Locate function....................................................................................67

1. Storing memory data........................................................................67

2. Locate..................................................................................................69

3. Auto Play mode..................................................................................70

4. Auto Return mode.............................................................................70

4-1. Setting the Auto Return Start/End point.......................................71

5. Auto Repeat mode.............................................................................74

Punch In/Out.........................................................................................75

1. Auto Punch In/Out............................................................................76

1-1. Storing the Punch In/Out point......................................................76

1-2. Auto Punch In/Out Rehearsal mode..............................................78

1-3. Auto Punch In/Out Take mode.......................................................79

1-4. Undo/Redo of Auto Punch In..........................................................80

2. Punch In/Out recording using a foot switch..................................81

2-1. Punch In/Out Rehearsal..................................................................82

2-2. Punch In/Out Take...........................................................................83

2-3. Undo/Redo of Manual Punch In/Out............................................84

Edit function.........................................................................................85

1. Copy & Paste......................................................................................86

1-1. Copying.............................................................................................86

1-2. Copy & Pasting.................................................................................88

1-3. Copy & Paste Undo/Redo................................................................90

2. Move & Paste......................................................................................91

2-1. Moving...............................................................................................91

2-2. Move & Pasting.................................................................................93

2-3. Move & Paste Undo/Redo...............................................................95

3. Erase....................................................................................................96

3-1. How to Erase data for a specific part

between ABS 0 and ABS END........................................................97

3-2. Undo and Redo of the erase operation..........................................98

3-3. How to Erase data in its entirety from

a specified point up to ABS END..................................................99

3-4. Undo and Redo of the erase operation........................................100

3-5. Erasing specific data......................................................................101

Saving/Loading Song Data...............................................................102

1. Saving the data using DATA OUT..................................................104

2. Loading the data using DATA IN ...................................................106

3. Saving the data using SCSI..............................................................108

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Introduction)

4. Compatibility with D-90, D-80 (V2.0),DMT-8 (V2.0),

and DMT-8VL.............................................................................116

MIDI sync function.............................................................................117

1. MIDI clock sync system..................................................................117

2. MTC sync/MIDI machine control system.....................................120

3. Multitrack system by the slave mode...........................................123

4. External MIDI equipment sync system by the slave mode.........127

5. Sync system with "adat" by the slave mode.................................130

6. Multitrack system using a D-90/D-80 (Ver.2)

/DMT-8 (Ver.2/VL)....................................................................133

Setup mode.........................................................................................137

1. How to enter the Setup Mode.........................................................137

2. How to set each mode......................................................................142

2-1. Track Swapping ("Track Exchange?")..........................................142

2-2. Time Signature Setting (Signature Set?").....................................143

2-3. Tempo Setting ("Tempo Map Set?").............................................145

2-4. Program Title setting ("TitleEdit PGM?").....................................147

2-5. Program Delete ("Delete PGM?")..................................................147

2-6. Metronome Setting ("Click ?")...................................................148

2-7. Preroll Time Setting ("Preroll Time?").........................................149

2-8. MIDI Sync Signal Out Setting (Midi Sync Out?").........................150

2-9. MTC Frame Rate Setting ("Frame Rate?")....................................151

2-10. MTC Offset Time Setting ("MTC Offset?")..................................152

2-11. MTC Offset Mode Setting ("MTC Offset?").................................153

2-12. Slave Mode Setting ("Slave Mode?")...........................................154

2-13. Slave Mode Type Setting ("Slave Type?")..................................155

2-14. Record Protect Setting ("Rec Protect?").....................................156

2-15. Digital Input Track Setting ("Digi. In?").....................................157

2-16. Digital Output Track Setting ("Digi. Out?")...............................159

2-17. Bar/Beat Resolution Mode Setting (" Resolution?").............160

2-18. MIDI Device ID Setting ("Device ID?")........................................161

2-19. Sampling Frequency Setting ("Sample Rate?").........................162

2-20. Event Number Check on Each Track ("NOs Of Event?")...........163

2-21. Current Drive Setting ("Drive Sel.?").........................................164

2-22. Loading Song Data ("Load PGM?").............................................165

2-23. Saving Song Data ("Save PGM?")................................................168

2-24. Formatting IDE/SCSI disk ("Disk Format?")..............................171

MIDI Implementation Chart................................................................172

MMC command list.............................................................................173

Inquiry Message list...........................................................................173

Fostex MIDI System Exclusive Message Format............................174

Maintenance..................................................................................189

Specifications................................................................................189

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Introduction)

Introduction

Thank you for purchasing the Fostex Model D-160.

The D-160 is a 16-track digital multitrack recorder with eight additional tracks that employs

a 3.5-inch E-IDE type removable hard disk as the recording media, instead of conventional

tape. An optional Model 9041 (1.3GB removable hard disk cartridge), is available for 16-

track (plus additional tracks) recording and playback.

A total of 240 minutes recording/playback time is available based on a single track

calculation.

The D-160 achieves high-quality recording/playback with 16-bit linear quantization and

a non-compression recording technique with two "Adat I/O" (switchable for S/P DIF),

which enables 16-track simultaneous recording (8 analog, 8 digital/16 digital) as well as

8-track simultaneous recording and 16-track simultaneous playback.

You can easily configure a fully digital recording system by combining the D-160 with

various types of digital mixing consoles. You can back up recordings from the hard disk

to an Adat machine, or to a DAT machine.

Also, high speed backup is available via a standard SCSI terminal.

The D-160 features a +/-6% Vari-pitch function, and various non-destructive edit functions,

such as copy, move & paste, erase, etc., that use three Time Bases.

Furthermore, it facilitates a complete MIDI environment by supporting MTC and MMC,

output of MIDI clock and Song Position Pointer via an internal Tempo Map, and advanced

controls by FEX.

It also has a Program Change function to manage up to 99 Programs, and you can assign

a title to each song (Program).

Installing an optional 8345 TC/SYNC card enables the D-160 to support slave operation

for the incoming LTC, and synchronization with video reference signals and Word Clock,

as well as to output Word Clock signal to an external digital device. Installing an optional

5041 balanced 8-16 I/O card would add +4dBu analog, balanced I/Os.

Please read this User's Guide thoroughly and keep it in a safe place so that you will be

able to produce high-definition, high tonal quality music and make the best use of the D-

160 for a long time.

Precautions

Notes about power supply

Be sure to connect the D-160 to the power supply specified in the Specifications

section of this Owner's Manual. Do not use an AC outlet of any other voltage.

Do not connect the D-160 to the same AC outlet to which devices that could generate

noise (such as a large motor or dimmer), or devices that consume a large amount

of power such as an air conditioning system or a large electric heater are connected.

If you use the unit in an area with a different power voltage, first consult your

dealer or the nearest FOSTEX service station. You can use the unit with a power

frequency of 50Hz or 60Hz.

It is very dangerous to use a power cord that is frayed or damaged.

In such a case, stop using the unit immediately and ask your dealer to repair

the cord.

To avoid possible electric shock and damage to the D-160, avoid contact with

water or other liquids. Do not handle the power plug while your hands are

wet.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Introduction)

To prevent possible electric shock and damage to the D-160, do not remove the

main unit cover or reach the inside the unit.

Do not let water or other liquids, or metal objects such as pins,

accidentally get into the D-160 because this may lead to electric shock or damage.

Should water enter the inside of the unit, remove the power plug from the AC

outlet, and consult your dealer or nearest FOSTEX service station.

To prevent damage to the D-160, be sure to turn on any connected devices

first, and then turn on the power to the D-160.

When you removing or connectting the cables to the input/output connectors

on the D-160, make sure that the channel INPUT faders and volume controls

are set to "0."

Notes on handling the hard disk

"FORMAT FIRST".

You need to format the optional hard disk prior to start recording if a brand

new hard disk drive has been installed.

Refer to the explanation of "2-24. Disk Format ?" menu on the Setup mode.

We recommend that you better the hard disk before you start fresh recording

on it.

However, be also aware of that the formatting process will erase all the recorded

song data.

The D-160 is equipped with a high-precision hard disk. Do not expose the unit

to excessive vibration at any time. In particular, do not move the unit or allow

any impact to the unit when the power is on.

Before turning the power off to the D-160, first quit Setup mode and make sure that the

recorder section is stopped. Especially, never attempt to turn off the power to the unit

while the hard disk is accessing data (the HD ACCESS LED is lit or flashing).

Otherwise, not only will you lose recorded data, but you may damage the D-160.

FOSTEX is not responsible for data lost during operation of the D-160.

Pack the D-160 in its shipping carton or an impact-resistant case, if you plan to

relocate it.

Make sure that the D-160 is kept free from external vibration or impact since

the it is very sensitive to vibration.

* If you wish to replace the included removable hard disk with another hard disk,

refer to "Before operating the D-160" on page "39."

Notes on the setup location

Do not install the D-160 in locations subject to the following:

* Extremely high or low temperature, or significant changes in temperature

* Excessive humidity or dust

* Excessive changes in power supply voltage

* Unstable or significantly vibrating or shaking surfaces

* Close to strong magnetic fields (such as a TV or speakers)

If you move the D-160 from a place with an excessively low temperature to a warm

place, or if you use the D-160 in a room in where the temperature varies significantly

during winter, condensation may occur on the hard disk or other parts.

In such cases, leave the D-160 in its new location for about an hour before you turn

on the power.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Introduction)

Notes on repair

The D-160 does not use any parts that users can repair easily.

Contact your dealer or the nearest FOSTEX service station to ask about repairs.

Do not throw the original carton box and packing material away.

You should use them when transporting the D-160.

The warranty will not cover damage due to improper packaging.

Also, Fostex is not responsible for damage occuring during transit.

About copyrights

It is prohibited by law to use any part of a CD recording or video images or audio data

for which a copyright is possessed by a third party for commercial purposes such as

contents, broadcasts, sales, or distribution - any purpose other than for your personal

pleasure.

About damages

Fostex is not responsible for any "direct damage" or "indirect damage" caused by

using the D-160.

Notes on using the Detachable Controller

When you use the detachable controller remotely using an extension cable, the D-

160 may malfunction due to electromagnetic interference. In this case, turn the

power off, and then on to the D-160 to restore the normal condition.

Fostex is not responsible for any malfunction of the D-160 caused by electromagnetic

interference.

How to use a dust cap (included)

Plug the included dust cap onto the connector of the D-160's removable hard

disk to protect the disk from static electricity, dust and dirt before you store or

transport the hard disk.

A hard disk is precision device. Handle it with care and avoid vibration,

humidity, strong magnetic fields, static electricity, dust, etc.

In particular, do not touch the connector with your hands to protect the hard

disk from static electricity.

Removable hard disk

Plug the dust cap onto the connector.

(Do not touch the connector with your

hands.)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Main features of D-160)

Main Features of D-160

The D-160 is equipped with the following functions:

* Employs a 3.5 inch E-IDE type removable hard disk system.

With an optional 9041 (1.3GB removable hard disk cartridge),

16-track (plus additional 8 tracks) recording and playback.

Total 240 minutes recording/playback time based on a single

track calculation.

* Non-compression recording/16 bit linear quantization and

sampling rates of 44.1kHz and 48kHz (assignable for each Program

and each playback), achieving true CD quality.

“Adat optical I/O” (switchable to S/P DIF), enables 16-track

simultaneous recording (8 analog, 8 digital). Connecting adat

output (x2) of a digital console and adat optical inputs (x2) of the

D-160 allows for 16-track simultaneous digital recording.

* Employs a new disk management method, “FDMS-3” (Fostex Disk

Management System-3). With this method, only the recorded

part consumes the disk space, which allows highly efficient

multitrack recording.

* Program Change function for managing up to 99 Programs (each

Program title editable).

Non-volatile locate memory for each Program, with a pre-roll time

of 0 - 10 seconds.

* Bar/beat Resolution function for storing memory in Bar/Beat units.

* Significantly improved efficiency with an FL display that features

a high-visibility 16-character indication.

* Erase Program function and Delete Program function, convenient

for efficient song management.

* MIDI IN/OUT/THRU terminals support the output of MIDI clock

and Song Position Pointers via an internal Tempo Map, as well as

support MTC/MMC. They also support advanced recorder control

via FEX (Fostex System Exclusive) for advanced functions. These

terminals, along with the functions to store the MTC output offset

by Bar/Beat, to store 24-hour MTC offset, and to display

external MTC (or LTC), will facilitate configuring an integrated

MIDI environment.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Main features of D-160)

* A programmable internal Tempo Map, with a selection of eleven

time signatures and a quarter note range of 30 to 250, and

Metronome function.

* REC Protect function to prevent accidental recording

* Number Of Events Monitor function that monitors the overflow

of events.

The number of created events can be displayed for each track.

* Installing an optional 8345 TC/SYNC card allows for the MTC-to-

LTC conversion and output, as well as the slave operation for

incoming LTC.

It also allows for synchronization with video reference signals

and Word Clock, as well as output of Word Clock signal to an

external digital device.

* Selectable reference time code (MTC/LTC), with six frame rates

(24/25/30ND/30DF/29.97ND/29.97DF).

* Wide selection of slave types (Vari, S/P DIF, adat, Free), 8345

clock (INT/VIDEO/WORD/AUTO), and WORD out (8345/D-160)

to support various sync environment. Eight Sync Presets available

to recall complex sync settings at once.

* The optional 5041 will add eight +4dBu, analog balanced inputs

(D-SUB25 pin x 1) and 16 outputs (D-SUB25 pin x 2) to the D-

160’s -10dBV unbalanced I/Os (RCA pin).

* Adat backup as well as conventional DAT backup supported.

Equipped with a standard SCSI interface, which allows for a high-

speed data backup to an external SCSI device.

Also, a Save Length Setting function enables backup of the

specified part of a Song.

* +/-6% Vari-pitch function for fine pitch adjustment without

significant tonal quality deterioration.

* Sixteen standard tracks, plus eight additional tracks (Tr. 17-24).

* Track Exchange function for swapping any tracks 1-24.

Track exchange of eight tracks (1-8, 9-16, 17-24) is also available.

* Detachable controller, which can be extended up to 10 meters

with two optional 8551 extension cables (5m).

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Main features of D-160)

* High-speed edit functions, typical for a hard disk, such as non-

destructive copy & paste, move & paste, erase, and undo/redo.

You can also specify the number of repeated operations (up to 99

times).

* Three Time Base (ABS, MTC, Bar/Beat), REMAIN indication based

on each Time Base, and indication of remaining hard disk space.

* Auto Punch In/Out with rehearsal, Auto RTN/Play, Locate ABS 0,

and Locate ABS END function for checking the recording end point.

* Digital scrubbing with the JOG dial, and audio cue with the

SHUTTLE dial.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

FRONT PANEL (with the detachable remote controller)

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

FRONT PANEL (with the detachable controller removed)

DIGITAL MULTITRACK RECORDER

D-160

POWER

REAR PANEL

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

TO RAIN OR MOISTURE.

AVIS

NE PAS OUVRIR

ANALOG OUT

ANALOG IN

DATA

1~8

SCSI

MIDI

OPTICAL

INPUT

9~16

OUTPUT

9~6 1~8

INPUT

OUTPUT

THRU

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

Names and Functions

DIGITAL MULTITRACK RECORDER

D-160

POWER

1. Detachable remote controller connector

The detachable remote controller is connected here.

You can remove the controller. Connect the optional extension cable (Model 8551) to

extend the distance.

* Refer to page "44" for information on extending the detachable remote controller connection.

2. Power switch

This switch turns the main power to the D-160 on/off.

Before turning the power off to the D-160, first quit the Setup mode and make sure that the

recorder section is stopped. Especially, never attempt to turn off the power to the unit while the

hard disk is accessing data (the HD ACCESS LED is lit or flashing).

Otherwise, not only will you lose recorded data, you may damage to the unit.

3. Controller mount

The detachable remote controller is mounted on the front panel.

4. Hard disk access LED

This LED lights up or blinks when the hard disk is writing or reading data. (Same as the

HD ACCESS LED on the detachable remote controller.)

5. Hard disk power LED

This LED lights up if the hard disk operates correctly when you turn the power on to the

unit. If the Lock key is unlocked, the power to the hard disk will not be turned on, and

the LED will not light up.

6. Removable hard disk cartridge slot

This slot is used to insert a removable hard disk cartridge. This system allows you to

replace the hard disk easily.

* Refer to page "41" for more information on how to replace the removable hard disk cartridge.

<Note>

This slot is covered by a dust-proof panel when the unit is shipped from the factory.

Remove this panel in order to insert a cartridge.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

<Note>

The D-160 package contains a removable case (without a hard disk). Install your hard disk in

this removable case.

The optional Model 9041 (1.3GB removable hard disk cartridge) contains a hard disk, which

allows you to record and play back about 15 minutes of data (16-tracks recording, FS: 44.1

kHz) without having to install a case.

* Refer to page "39" for more information on the hard disk models that have already been

ested for operation on the D-160.

7. Lock/Unlock key

When you remove or install the hard disk cartridge, you need to lock/unlock here using

the included key.

<Note>

Be sure to turn the power off to the D-160 before locking or unlocking.

11 13

14 17

16 15 18 19

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

39 40

31 34 35 36 37 38 25 24

32 30 29 28 33

8. Meter display

This meter display shows the signal level and settings.

* Refer to the “Display section” on page "25."

9. Record Track Select key [RECORD TRACK]

The Record Track Select key selects "SAFE-READY" for the recording track.

When you press this key once, the track enters the READY status, and the track indication

on the display will blink. Pressing it again changes this status to "SAFE" and the track

indication will go out. When you start recording, the blinking track indication illuminates.

When you press only the RECORD button while the track is in the READY status, the track

becomes an input monitor, allowing you to adjust the recording level.

Pressing only the RECORD button again, and the track become a reproduction monitor.

This key is also used to select a track for the Copy & Paste, Move & Paste, Erase, or other

editing operation.

* Refer to page "37" for details about the reproduction monitor and the input monitor.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

10. Shift key [SHIFT]

Use this key to choose recording tracks.

When the shift LED lights off, it allows you to choose track 1~8.

When the LED is on, tracks 9~16 can be chosen.

11. Auto Play/Auto Return key

Pressing this key repeatedly will change Auto Play mode, Auto Return mode, and Repeat

mode On/Off as follows: (

: LED off,

: LED light up)

AUTO RTN

AUTO PLAY

Auto Play/Auto Return OFF (All LEDs are off.)

Auto Play ON (Only the AUTO PLAY LED is lit.)

AUTO RTN

AUTO PLAY

AUTO RTN

AUTO PLAY

Auto Return ON (Only the AUTO RTN LED is lit.)

AUTO RTN

AUTO PLAY

Auto Repeat ON (Both AUTO PLAY and AUTO RTN LEDs are lit.)

Auto Play mode:

In this mode, playback will start automatically after the START point is located.

This function is effective at any locate points other than the ABS END point.

Auto Return mode:

When the END point is reached during playback, the START point is automatically

located in this mode. This function is effective only when the START and END points

have been specified.

<Note>

The Auto Return function is works only during playback. In the recording mode, the

START point will not be located automatically when the END point is reached.

Auto Repeat mode:

This mode is a combination of Auto Play and Auto Return, and plays back the part

between the START and END points repeatedly. The auto repeat function is effective

only when the START and END points have been specified correctly.

* Refer to page "67" for details.

12. Clipboard In key [CLIPBOARD IN]

This key is used to store and recall the In point (CLIPBOARD IN point) for the Copy or

Move operation. You can locate a stored CLIPBOARD IN point.

* Refer to page “85” for copying/moving data.

* Refer to page "67" for locating the CLIPBOARD IN point.

13. Clipboard Out key [CLIPBOARD OUT]

This key is used to store and recall the Out point (CLIPBOARD OUT point) for the Copy or

Move operation. You can locate a stored CLIPBOARD OUT point.

* Refer to page "67" for locating the CLIPBOARD OUT point.

* Refer to page "85" for copying/moving data.

14. Auto Return Start key [AUTO RTN START]

This key is used to store and recall the start point (AUTO RTN START point) for the Auto

Return or Auto Repeat operation.

You can locate a stored AUTO RTN START point.

* Refer to page "69" for more information about Auto Return and Auto Repeat.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

15. Auto Return End key [AUTO RTN END]

This key is used to store and recall the end point (AUTO RTN END point) for the Auto

Return or Auto Repeat operation.

You can locate a stored AUTO RTN END point.

* Refer to page "69" for more information about Auto Return and Auto Repeat.

16. Auto Punch In key [AUTO PUNCH IN]

This key is used to store and recall the recording start point (AUTO PUNCH IN point) for

the Auto Punch IN/OUT operation. This point is also used as an erase point.

You can locate a stored AUTO PUNCH OUT point.

* Refer to page "75" for more information about Auto Punch In/Out recording.

* Refer to page "85" for more information about pasting data.

* Refer to page "96" for more information about the Erase operations.

17. Auto Punch Out key [AUTO PUNCH OUT]

This key is used to store and recall the recording end point (AUTO PUNCH OUT point) for

the Auto Punch IN/OUT operation. This point is also used as an erase point.

You can locate a stored AUTO PUNCH OUT point.

* Refer to page "75" for more information about Auto Punch In/Out recording.

* Refer to page "96" for more information about the Erase operation.

Memory keys (CLIPBOARD IN, CLIPBOARD OUT, AUTO RTN START, AUTO PUNCH

IN, AUTO PUNCH OUT, and AUTO RTN END keys) have the following common

functions:

* Pressing a Memory key to recall the point the key is storing (or pressing the RECALL

key, and then the Memory key) displays the memory data (time, or bar/beat/clock)

currently stored in that key; then the unit enters data edit mode. To edit data, use

the HOLD/> key or the SHUTTLE dial to move among the digits, and then use the JOG

dial to change the value.

* After you finish editing data, press the STORE key, and then press one of the Memory

keys into which you want to store the point. The edited data will be stored in the

specified Memory key.

* While the current position of the recorder is indicated, press the STORE key, then one

of the Memory keys into which you want to store the data. The current position or the

recorder will be stored in the Memory key. You can do this while the recorder is

running or stopped.

* Press a desired Memory key, and then press the LOCATE key to locate the point stored

in that Memory key (time, or bar/beat/clock).

* All memory data can be stored to Programs 1-99 individually.

* In Setup mode, you can save or load song data for each Program.

* All data will be retained after you turn off the power.

* Refer to page "67" for more information on memory data.

* Refer to page "67" for more information on the Locate function.

* Refer to pages "28" and "49" for more information on the Program Change function.

* Refer to page "102" for more information on saving and loading song data.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

18. Display Select key [DISP SEL]

This key is used to change the display mode. Pressing this key repeatedly will change the

display mode as follows:

Disk space (remain).

The Setup mode display

When time base is "MTC", the

The current position

(SETUP is blink) and title

MTC or LTC time that is input will

display

be displayed.(at installed Model

8345)

* Refer to pages "26" and "32" for more information about the REMAIN.

Pressing this key while holding down the EXECUTE/YES key will switch the Time Base (*)

as follows. The Time Base can be set when the display shows the recorder's current

position or the available disk space (REMAIN).

ABS (Absolute Time)

BAR/BEAT/CLK

MTC (MIDI Time Code)

(*) Time Base:

The D-160 uses time display (ABS or MTC) or Bar/Beat/Clock display to indicate the current

position of the recorder section. These displays are called "Time Base." ABS (Absolute Time)

shows the absolute time of the disk, and MTC (MIDI Timecode) shows the relative time obtained

by adding an MTC offset value to the ABS value. Bar/Beat/Clock (BAR/BEAT/CLK) indicates a

position within a piece of music and conforms to the MIDI clock and Song Position Pointers

created on the internal Tempo Map. The tune will be displayed up to 999 bars.

* Refer to pages "38" and "145" for more information about MTC and the internal Tempo

Map.

19. Execute/Yes key [EXECUTE/YES]

Press this key to execute the operation when you edit data on the hard disk using the

edit functions such as Paste and Erase, when you put the D-160 into SETUP mode, or

when you set the parameters in the SETUP menu.

Pressing the DISP SEL key while holding down the EXECUTE/YES key allows you to select

the Time Base. (Refer to the explanation about the DISP SEL key.)

* Refer to page "85" for more information about using this key for the Paste or Erase operation.

* Refer to page "137" for more information about using this key in SETUP mode.

20. Exit key/No key [EXIT/NO]

The opposite of the EXECUTE/YES key, this key is used to stop the operation.

* Refer to page "85" for more information about using this key for the Paste or Erase operation.

* Refer to page "137" for more information about using this key in SETUP mode.

21. Recall key [RECALL]

Press this key to recall the stored time value (or Bar/Beat/Clock value).

Pressing this key, and then one of the following keys will display the data stored at the

key you pressed, and you will be able to edit the data.

RECALL key -> CLIPBOARD IN key

RECALL key -> CLIPBOARD OUT key

RECALL key -> AUTO PUNCH IN key

RECALL key -> AUTO PUNCH OUT key

RECALL key -> AUTO RTN START key

RECALL key -> AUTO RTN END key

RECALL key -> LOCATE key

The Clipboard In point is recalled and the D-160 enters the edit mode.

The Clipboard Out point is recalled and the D-160 enters the edit mode.

The Auto Punch In point is recalled and the D-160 enters the edit mode.

The Auto Punch Out point is recalled and the D-160 enters the edit mode.

The Auto Return Start point is recalled and the D-160 enters the edit mode.

The Auto Return End point is recalled and the D-160 enters the edit mode.

The Locate key data is recalled and the D-160 enters the edit mode.

To exit edit mode, press the EXIT/NO key, DISP SEL key, or STOP button.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

* Refer to page "85" for more information about the clipboard.

* Refer to page "75" for more information about Auto Punch In/Out recording.

* Refer to page "70" for more information about Auto Return.

22. Store key [STORE]

This key is used to store a time value (or Bar/Beat/Clock value) to one of the memory

keys. Pressing this key, and then one of the following keys will cause the data shown on

the display to be stored to the corresponding memory key you pressed. Pressing the

STORE key while holding down the HOLD/> key will change a Program.

STORE key -> CLIPBOARD IN key

STORE key -> CLIPBOARD OUT key

STORE key -> AUTO PUNCH IN key

STORE key -> AUTO PUNCH OUT key

STORE key -> AUTO RTN START key

STORE key -> AUTO RTN END key

STORE key -> LOCATE key

Data is stored as a Clipboard In point.

The stored data can be used as a locator.

Data is stored as a Clipboard Out point.

The stored data can be used as a locator.

Data is stored as an Auto Punch In point.

The stored data can be used as a locator.

Data is stored as an Auto Punch Out point.

The stored data can be used as a locator.

Data is stored as an Auto Return Start point.

The stored data can be used as a locator.

Data is stored as an Auto Return End point.

The stored data can be used as a locator.

Data is stored as a LOCATE key data.

After pressing this key, if you wish to cancel the store operation, press the EXIT/NO key,

DISP SEL key, or STOP button.

* Refer to page "85" for more information about the clipboard.

* Refer to page "28" and "49" for more information about Program Change function.

* Refer to page "67" for more information about the Locate function.

* Refer to page "75" for more information about Auto Punch In/Out recording.

* Refer to page "70" for more information about Auto Return.

23. Hold/Digit Move key [HOLD/>]

Pressing this key while the recorder transport is operating will hold the time value (or

Bar/Beat/Clock value), display the value on the screen, and will place the D-160 into edit

mode. If you press this key while the recorder section is stopped, the D-160 will enter

edit mode. Pressing this key repeatedly allows you to select the digit (column) to edit.

To cancel edit mode, press the STOP button, DISP SEL key, or EXIT/NO key.

Pressing the STORE key while holding down the HOLD/> key will change the Program.

* Refer to pages "67" and "85" for more information about using this key.

24. Jog/Shuttle dial

Jog dial (inside):

Turning the JOG dial while the recorder is stopped performs digital scrubbing in either

direction, which allows you to check the audio and locate a point without any change

in pitch.

The JOG dial is also used to change values in the data edit mode or when the pitch

data is displayed. It also allows you to select a parameter to set in Setup mode.

Shuttle dial (outside):

FWD and REW direction shuttle operation in the STOP mode is possible at +/-1 ~ 64

times fast winding in the no sound state. On the other hand, FWD and REW direction

shuttle operation in the PLAY mode is possible in the CUE playback mode at +1 ~ 8 and

-1 ~ -7 times speed while cueing. In addition, while in the display edit mode, the

editing point can be moved in the same way as by the HOLD/> key.

* Refer to pages "67" and "85" for more information about the editing the memory data.

* Refer to page "137" for more information about Setup mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

25. Redo key [REDO]

Pressing this key after you press the UNDO key restores the status obtained before you

undo recording or editing. This key is activated only when the recorder transport section

is stopped.

* Refer to pages "75" and "85" for more information about the Redo operation.

26. Undo key [UNDO]

After using an edit function such as Paste, or Erase, or after auto punch in/out recording,

pressing this key will restore the previous status before editing or recording.

This key is activated only when the recorder transport section is stopped.

* Refer to pages "75" and "85" for more information about the Undo operation.

27. Erase key [ERASE]

This key is used to erase a specified area or all data after a specified point on certain

“READY” track(s), or all the data in a specified Program.

Use the Auto Punch In/Out points and the RECORD TRACK select key to specify the area to

erase.

To erase all data in a Program, press the STORE key while holding down the HOLD/> key

to select the Program, then press the ERASE key.

All data recorded in the Program will be erased. You do not need to set a track in READY

mode.

* Refer to page "96" for more information about the Erase operation.

28. Vari-pitch key [VARI PITCH]

Use this key to turn the Vari-pitch function on and off. When this function is enabled, the

corresponding LED lights up. When this function is disabled, the LED turns off.

The range of pitch variation for playback and recording is +/-6.0%, in 0.1% steps.

Press the RECALL key, and then the VARI PITCH key to display the current pitch data.

To change the pitch data, use the JOG dial to change the value while the pitch data is

displayed.

You can also change the playback speed when the data is being played back with the Vari-

pitch function ON.

* To quit the pitch data display, press the EXECUTE/YES key, the EXIT/NO key, or the

STOP button.

<Note>

Even when the vari-pitch data is set to 0.0%, pressing this key will turn the LED on.

<Note>

You cannot change the pitch data while recording. If the Vari-pitch function was on, the unit will

use the pitch data previously set.

<Note>

The Vari-pitch function will be automatically turned off in the following situations:

* When you turn on the power to the unit (The pitch data will be reset to 0.0%.)

* When you set Slave mode ON. (The pitch data remembers the previous setting.)

* When you set up the digital input tracks and “DIGITAL” appears on the display. (The pitch data

remembers the previous setting.)

If you have installed an optional Model 8345 TC/SYNC card in the D-160 and you have set the

“Word Out?” menu in the Setup mode to “8345,” the Vari-pitch function turns on even during digital

input via DIGITAL IN.

* Refer to page "56" for more information on the Vari-pitch function.

* Refer to page "123" for more information on Slave mode.

* Refer to page "60" for more information on digital signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

29. Paste key [PASTE]

Press this key to copy data or move data that has been copied to the clipboard to a

location stored at the AUTO PUNCH IN key. The data will be pasted at the point stored in

the Auto Punch In key. You can select the paste destination track using the RECORD

TRACK select key. A destination track to which data is pasted is identical to the source

track. This key is activated only when the recorder transport section is stopped.

* Refer to page "85" for more information about the Copy & Paste, and Move & Paste operation.

30. Move key [MOVE]

This key is used to enter into the clipboard data stored in memory by the CLIPBOARD IN/

OUT keys. Pressing the MOVE key will store the data in the Clipboard as Move data.

To enter data to be moved, one or more tracks must be readied, and a correct value must

be stored for the In and Out points. If you attempt to enter data when all tracks are safe,

all track indications and "Select Track!" indication on the display will blink to warn you.

If a correct value is not set for the Clipboard In or Out points, a warning message of “Void

In Point!” or “Void Out Point!” will appear.

* Refer to page "85" for more information about the Copy & Paste, and Move & Paste operation.

31. Copy key [COPY]

This key is used to copy data stored in the memory using the CLIPBOARD IN/OUT keys.

Pressing the COPY key will store the data in the Clipboard as Copy data. To execute the

copy operation, one or more tracks must be readied, and a correct value must be stored

for the In and Out points. If you attempt to copy data when all tracks are safe, all track

indications and a "Select Track!" indication on the display will blink to warn you.

If acorrect value is not set for the Clipboard In or Out points, a warning message of “Void

In Point!” or “Void Out Point!” will appear.

* Refer to page "85" for more information about copying data.

32. Auto Punch Mode On/Off key [AUTO PUNCH]

Switch this key ON for auto punch in/out.

When you press this key while a correct value is stored to the AUTO PUNCH IN key and the

AUTO PUNCH OUT key, both the REHEARSAL LED and TAKE LED will blink, indicating that

Auto Punch mode is on. (If a correct value is not stored, pressing the AUTO PUNCH key

will not turn the parameter ON, and the message “Void Out Point!” will appear.)

Pressing the PLAY button under this condition will put the unit into "Rehearsal mode" for

Auto Punch In/Out recording. Pressing the PLAY button and RECORD button simultaneously

will put the unit into "Take mode."

There are five combinations of the REHEARSAL LED and TAKE LED that indicate the status

of the unit regarding auto punch recording:

<Note>

If a correct value is not stored, pressing the AUTO PUNCH key will not enable the function,

and the message “Void Out Point!” will appear.

If a correct value is not stored, pressing the AUTO PUNCH key will not turn on the function, and the

message “Void Out Point” will alert you. In this case, set a correct value for the Auto Punch In/Out point.

Also, the function is not turned on when you press the AUTO PUNCH key if the disk does not have

enough recording space. The display will indicate “-**h**m**s**f Over.”

Auto Punch mode OFF

Auto Punch mode ON

Auto Punch Take mode

Both REHEARSAL LED and TAKE LED are off.

Both REHEARSAL LED and TAKE LED are blinking.

Only the TAKE LED (red) is lit.

Auto Punch Rehearsal mode Only the REHEARSAL LED (green) is lit.

Rehearsal mode entered by

means of MMC or foot switch

Only the REHEARSAL LED (green) is blinking.

* Refer to page "75" for more information about the Punch In/Out.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

AUTO

REHEARSAL

PUNCH

Punch In/Out mode and LED display

Rehearsal

TAKE

Auto Punch In/Out mode

AUTO

REHEARSAL

PUNCH

AUTO

REHEARSAL

TAKE

PUNCH

TAKE

Take

Punch In/Out mode

AUTO

PUNCH

REHEARSAL

TAKE

Rehearsal

Manual Punch In/Out using a

footswitch or MMC. (Auto

Punch mode OFF.)

AUTO

PUNCH

REHEARSAL

TAKE

AUTO

Take

REHEARSAL

PUNCH

TAKE

:blink

:go off

:light up

33. Locate key [LOCATE]

Press this key to locate a position.

You can locate a point (memory data) (time, or bar/beat/clock) stored in the Memory

keys when you press a Memory key (CLIPBOARD IN, CLIPBOARD OUT, AUTO RTN START,

AUTO PUNCH IN, AUTO PUNCH OUT, or AUTO RTN END), and then press the Locate key.

Data stored in the Locate key is the most-recently located position expressed as a time

value (bar/beat/clock). If you wish to locate the same point repeatedly, then press this

key repeatedly. If you locate a position at a different time value or bar/beat/clock value,

the data will be updated. Pressing the RECALL key, and then the LOCATE key will display

the data stored in the LOCATE key (time or bar/beat/clock), and put the D-160 in the

data edit mode. To edit the data, use the HOLD/> key or the SHUTTLE dial to move around

the digits, and then use the JOG dial to change their value.

When you finish editing the data, you can store a particular locate point by pressing the

STORE key, and then the LOCATE key. You can also store a locate point by pressing the

STORE key, and then the LOCATE key while the recorder’s current point is shown.

Also, pressing the HOLD/> key to enter data edit mode, and then pressing the LOCATE

key when you finish editing, will allow you to locate the edited position (bar/beat/clock)

directly. This data can be stored individually to each Program P1-P99.

In the SETUP mode, you can also save and load the song data to and from each Program

individually. The data will be retained after you turn off the power to the unit.

* Refer to page "67" for more information about the Locate function.

34. Record button [RECORD]

Pressing only this button places the readied tracks into input monitoring status.

Pressing this button again will reset the tracks to playback monitoring. (The RECORD LED

will blink when the readied tracks are in input monitoring status.)

Pressing the PLAY button while holding down this button will place the readied tracks

into recording. At this time, the PLAY LED and RECORD LED will light, and the readied

track indication will be light steadily (instead of blinking).

* Refer to page "37" of the "Before Operating" section for more information about input

monitoring and reproduce monitoring.

35. Stop button [STOP]

Pressing this button will stop the transport section of the recorder.

Pressing the PLAY, REWIND, or F FWD button while holding down this button will cause

the D-160 to perform the following operation:

STOP + PLAY

Clipboard playback (The STOP LED will flash and the PLAY LED will

light up.) *3

STOP + REWIND

STOP + F FWD

Locate ABS 0 *4

Locate ABS END *5

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

Pressing the STOP button will abort the editing operations and display the current

position of the recorder, if you wish to:

* quit the data edit mode,

* cancel the recall or store operation,

* quit the pitch data display,

* cancel the edit operation, such as pasting, or

* cancel the SETUP menu settings.

Pressing the foot switch while holding down this button allows you to turn the punch in/

out rehearsal mode ON/OFF.

*3 Clipboard playback:

The D-160 plays back the copy data or move data for the Clipboard. During audio playback

of the copy or move data, the FL will display the time length and data type (“Copy Clip

Play!” or “Move Clip Play!"), and the copy or move source track indicator will flash, enabling

you to quickly determine the track and data type.

*4 Locate ABS 0:

The D-160 will locate the top of the selected Program (ABS TIME: 00m: 00s: 00f).

*5 Locate ABS END:

The D-160 will locate the end of the recorded data on the Program (ABS END).

* These operations can be executed only on real tracks 1 ~ 16.

* Refer to page "32" of the "Before Operating" section for more information about ABS 0 and

ABS END.

* Refer to page "81" for more information about Punch In/Out recording using the foot switch.

36. Play button [PLAY]

Pressing this button will cause the recorder to play back.

Pressing this button while holding down the RECORD button will start recording.

Pressing this button while holding down the STOP button will perform the Clipboard

playback operation. Refer to the section “STOP Button” for more information on the

Clipboard playback.

Pressing the PLAY button during recording will stop recording.

37. Rewind button [REWIND]

Pressing this button while the recorder section is stopped will rewind data at 30 times

speed. Pressing this button in Play mode will cue data (you can hear sound while rewinding)

at five times speed.

Pressing this button while holding down the STOP button will perform the "LOCATE ABS

0" operation, and immediately locate the beginning of the Program (ABS TIME: 00m: 00s:

00f). (Refer to the "STOP button" section for more information about LOCATE ABS 0.)

38. Fast Forward button [F FWD]

Pressing this button while the recorder section is stopped will fast forward data at 30

times speed. Pressing this button in Play mode will cue data (you can hear sound during

the fast forward operation) at five times speed.

Pressing this button while holding down the STOP button will initiate the "LOCATE ABS

END" operation, and immediately locate the end of the recorded data on the Program

(ABS END). (Refer to the "STOP button" section for more information about LOCATE ABS

END.)

39. Locked LED [LOCKED]

The Locked LED will blink when the D-160 is setup as slave mode.

It will light on when the lock is achived.

* Refer to page "123" for more information about "Slave Mode Function."

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

40. Hard disk access LED

This LED lights up or blinks when the hard disk is writing or reading data.

Do not turn the power off while this LED is lit or blinking. Otherwise, data on the hard disk may

be damaged.

41. MIDI Time Code In LED [MTC IN]

This LED lights up when MTC (MIDI Time Code) is input from an external MIDI device to

the MIDI IN connector of the D-160.

42. Punch In/Out jack [PUNCH IN/OUT] (Connector: PHONE jack)

Connecting the optional foot switch will let you control punch In/Out (and rehearsal)

recording. Use a Fostex Model 8051 foot switch.

<Note>

Be sure to use an “unlatch type” foot switch if you use a foot switch other than the Model 8051.

Otherwise, a malfunction could occur.

* Refer to page "81" for information about Punch In/Out recording using the foot switch.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

TO RAIN OR MOISTURE.

AVIS

ANALOG OUT

ANALOG IN

3 2

DATA

SCSI

MIDI

OPTICAL

INPUT

OUTPUT

9~6 1~8

9~16 1~8

INPUT

OUTPUT

THRU

45 46

43. Input jack [ANALOG IN 1-8] (connector: RCA pin)

Analog audio signal from the mixer is routed here.

Connect this jack to the Group out (BUSS OUT) connector of the mixer.

44. Output jack [ANALOG OUT 1-16] (connector: RCA pin)

Analog audio signal of the D-160 is output here.

Connect this jack to the TAPE IN connector of the mixer.

45. Data Input connector [DATA INPUT 1-8, 9-16] (connector: OPTICAL)

Use this connector to load song data (audio + setup data) from an external device to the

D-160. It is also used to input S/P DIF digital signal (from a DAT, CD, or MD) or adat

digital signal (from RD-8, CX-8, or adat). DATA INPUT 9-16 is constantly fixed to "adat"

input.

* Refer to pages "102" and "165" for information about "LOAD" function.

* Refer to page "60" for information "Digital Recording."

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

<Note>

Use the DATA INPUT 1-8 connector to load song data to the D-160.

Do not use the DATA INPUT 9-16 connector with load .

46. Data Output connector [DATA OUTPUT 1-8, 9-16] (connector: OPTICAL)

Use this connector to save song data (audio + setup data) from the D-160 to an external

device. It is also used to output S/P DIF digital signal or adat digital signal to an external

digital device. DATA OUTPUT 9-16 is constantly fixed to "adat" output.

<Note>

Use the DATA OUTPUT 1-8 connector to save song data from the D-160.

Do not use the DATA OUTPUT 9-16 connector with save.

* Refer to pages "102" and "168" for information about "SAVE" function.

* Refer to page "60" for information "Digital Recording."

47. SCSI connector [SCSI] (connector: D-sub 25-pin)

This is the connector which enables an external SCSI device to be connected.

It allows you to save or load song data.

Use the D-sub 25-pin cable for Macintosh designated by each SCSI device.

* Refer to pages "108" and "166" for information about "SCSI."

48. MIDI Input/Output/Thru connector [MIDI INPUT/OUTPUT/THRU]

(connector: DIN 5-pin)

MIDI INPUT:

Connect the MIDI OUT connector of an external MIDI device here.

The D-160 can be controlled remotely via an external MMC (MIDI Machine Control) or

FEX (Fostex System Exclusive Message).

MIDI OUTPUT:

Connect the MIDI IN connector of the external MIDI device here.

The D-160 will output MTC (MIDI Time Code), MIDI Clock signal, MMC (MIDI Machine

Control) response, and FEX (Fostex System Exclusive Message) response.

MIDI THRU:

This connector outputs the input signal at the MIDI INPUT connector without modification.

When using multiple D-160s via MIDI, connect this terminal to the MIDI INPUT connector

of the second D-160. Refer to page "117" for details.

49. Panel A for an optional card

This is the panel used for installing the optional Model 5041 (balanced 8-16 I/O card).

Using the Model 5041 allows for balanced analog signal input and output. In general,

leave the panel in place.

50. Panel B for an optional card

This is the panel used for installing the optional Model 8345 (D-160 TC/SYNC card).

Using the Model 8345 makes the D-160 have LTC input and output connectors.

Also, the sync lock with video and word clock will be possible. In general, leave the panel

in place.

51. Power cable

Connect the power cable to an AC outlet of the specified voltage.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

The D-160 display integrates the level meter of a high-visibility FL tube with a 16 digits and

35 dot message display.

The level meter shows the Track 1-16 output level of the recorder section. The time display

shows the current time of the recorder section using ABS TIME (Absolute time), MTC (MIDI

timecode), or MIDI BAR/BEAT (bar/beat). This display also shows messages required for

interactive operation. The following section explains the display functions and provides with

some examples.

1. Display shown when the power is turned on

When you turn on the power to the D-160, the display shows "Initializing..." (Initializing.

Please wait.), and the time display shows the time using the time base (ABS, MTC, or BAR/

BEAT/CLK) that was selected before the power was turned off.

44.1kHz

∞

2. Preset display

TC MTC IN OFFSET

ABS SETUP CHASE

LOCATE

REMAIN PGM

FORMAT

SIGNATURE

TEMPO

44.1kHz 48kHz

COMPLETED !

SURE ?

MIDI CHASE

SAVE LOAD

EXT SYNC

DIGITAL

∞

1. Level meter

The level meter shows the recorder output level and the recording level for Tracks 1-16.

2. Track indication

The track indication blinks when the corresponding track is ready. It turns off when the

track is safe, and is lit during recording.

3. ABS, MTC, SIGNATURE

When Time Base uses ABS time, “ABS” lights up. With MTC time, “MTC” lights up, and with

BAR/BEAT/CLK indication, “SIGNATURE” lights up.

4. LOCATE

This LED lights up when the unit enters data edit mode, enabling you to edit data.

Pressing the LOCATE key while this LED is lit will cause the D-160 to locate the position of

the displayed time or the bar/beat/clock value.

5. REMAIN

Refer to "2. Switching the display using the DISP SEL key."

6. SETUP

Refer to "2. Switching the display using the DISP SEL key."

7. COMPLETED!

This message indicates that an operation such as copy, move, and paste has been completed.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

8. SURE?

This message is shown to confirm whether or not you wish to execute a certain operation.

9. LOAD, SAVE, FORMAT, MTC OFFSET, TEMPO

When the unit enters Setup mode, the selected parameter name will appear here.

The parameter name also appears on the 35 dot message Display.

10. MIDI

This indication lights up when the D-160 receives effective MIDI messages from an external

MIDI device.

11. DIGITAL

This indication lights up when the D-160 is receiving a digital signal properly at the DATA

INPUT connector while loading data from a external digital equipment (CD, MD etc.).

If this indication is blinking, the digital signal is not being received correctly.

12. 35 dot message Display

This display indicates the ABS time, MTC time, BAR/BEAT/CLK time value or bar/beat/

clock value, a Program number, and a parameter name in the Setup mode.

13. CHASE

This indication flashes when the D-160 is in Slave mode, and lights up when the unit locks

to the sync signal.

14. 44.1kHz, 48kHz

This displays the sampling rate of the Program you are currently working.

During DIGITAL input of S/P DIF, the 44.1kHz or 48kHz indication will blink when the FS

setteing is different between the digital signal that is input and that in D-160.

15. MTC IN, TC IN

With the optional Model 8345 TC/SYNC card installed, this will be lit when MTC or LTC is

externally input.

16. PGM

This flashes when the D-160 is enterd in the program setup and program change modes.

17.

At playback of a no sound section, if the FL tube " ∞" symbol only is lit, the level of that

track will be lower than 43dB but it also indicates that an Audio File exists in the lighted

track.

You proceed as is but the hard disk is occupied in excess by this Audio File.

If this Audio File is unneeded, disk capacity can be economizied by erasing this section.

Likewise, during playback, if nothing is lit in the FL tube " ∞" section, it means that

Audio data of this track is "ALL 0" and the hard disk is not occupied by this.

3. Switching the display using the DISP SEL key.

Let's assume that you turned off the power while the time display was using a time base of

"ABS," and then you turned the power on again. The D-160 time display will again use a time

base of "ABS." (Underline->Displayed program number)

ABS TIME display

ABS

44.1kHz

∞

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

At this time if you press the DISP SEL key, the Disk Remain display will appear. (Both

recordable time and hard disk capacity remaining will be converted to mono track and

expressed in time and megabites.)

DISK REMAIN display

REMAIN

44.1kHz

∞

If "BAR/BEAT/CLK" is selected for the timebase (explained later), the DISK REMAIN

indication will show a value (in terms of the number of measures) calculated based on the

last beat/tempo data on the tempo map of the recorded song.

When you press the DISP SEL key again, the Setup mode display will appear.

At this time, the D-160 has not entered the Setup mode. To put the D-160 into the Setup

mode, press the EXECUTE/YES key. After pressing the EXECUTE/YES key, if you wish to go

back to the previous status, press the EXIT/NO key.

Setup mode display ("SETUP" indication is flashing)

SETUP

44.1kHz

∞

If you press the DISP SEL key again, the screen will return to the "ABS TIME" display.

4. Switching the Time Base display using the EXECUTE/YES key and

DISP SEL key

When the screen is showing the ABS TIME or REMAIN display, if you press the DISP SEL key

repeatedly while holding down the EXECUTE/YES key, the TIME BASE display will change

cyclically. You can select one of the following Time Base displays.

ABS (Absolute Time)

ABS

44.1kHz

∞

BAR/BEAT/CLK (Bar/Beat/Clock)

SIGNATURE

44.1kHz

∞

MTC (MIDI Timecode)

MTC

44.1kHz

∞

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

5. Changing Programs using the STORE key and the HOLD/> key

* About the Program Change function

The Program Change function divides the hard disk space into up to 99 parts to

accommodate 99 separate Programs (P01-P99 — as long as available recording

time allows) so you can record, play back, edit, and archive (save and load) data

for each Program individually.

For example, the first song can be Program 1, the second song can be Program 2,

etc. You need to recall the desired Program before you start recording, playback,

editing, or archiving.

Pressing the STORE key while holding down the HOLD/> key will cause the D-160 to enter

Program select mode, display the message “Select PGM !”, followed by the current Program

and Program number and a flashing “SURE?” indication.

PGM

44.1kHz

∞

PGM

44.1kHz

SURE?

∞

You can select the desired Program from the already setup Programs by rotating the JOG

dial while the Program number and “SURE ?” are flashing. ("#0003" is the current program

title.)

After you select a Program, press the EXECUTE/YES key to return to the selected Program’s

ABS indication.

The Time Base display will indicate the selected Program’s Time Base, since you can set

the Time Base for each Program individually.

To change the Time Base display after you have selected the desired Program, press the

DISP SEL key while holding down the EXECUTE/YES key.

Pressing only the DISP/SEL key will take you to the REMAIN display based on the current

Time Base.

<Notes>

* If you turn the JOG dial while the ABS display or MTC display indicates a Program number,

the Program number indication will change to the sub-frame indication. However, if you

operate a transport button, such as the PLAY button or the Stop button, or if you turn the

SHUTTLE dial, the sub-frame indication will change back to the Program number indication.

(The Program number shown on the BAR/BEAT/CLK display will not change.)

* The maximum total recording time of all setup Programs (up to 99 Programs) equals the

available recording time of the hard disk. For example, if you use an optional Model 9041

(1.3GB removable hard disk cartridge), the available 16-track recording time is about 15

minutes (with a sampling rate of 44.1kHz). If you have recorded 10 minutes of data in

Program 1, you can record 5 minutes for the total time of the rest of Programs. That is, you

can record data totalling 15 minutes, regardless of whether you use all setup Programs or

record only one Program.

* Refer to “2-1. Setting up a Program” and “2-2. Program Change” on pages 49-51 for more

information on how to setup a new Program and use the Program Change function.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

6. Warning messages

If you perform an incorrect operation, input incorrect data, or if an error occurs,

the following alarm indication appears:

Invalid data indication (The input data is not appropriate for the operation).

Action to take:

Input correct data.

∞

Invalid In/Out indication (The In or Out point is not appropriate for the operation).

Action to take:

Input correct data.

∞

Overtime indication (Available disk space is insufficient for the length of time (the number

of measures) indicated on the display.)

Action to take:

During the copy & paste and move & paste operation, try to shorten the length

of the copied data by the indicated amount. Alternatively, use the "ERASE"

function to move the ABS END point backward to obtain enough disk space for

editing.

∞

Unassigned track indication (Select any track)

Action to take:

Use the RECORD TRACK select key to ready any track.

∞

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

Event overflow indication (The editing points are overflowed)

Action to take:

You edited too much. The warning means "you cannot paste or erase any more."

In regards to event, refer to "Event and Audio File" in Before Operating section.

∞

Load error indication (You cannot load data because the data input to the DATA INPUT

connector contains an error)

Action to take:

Check to see if there is an abnormality with the external digital machine

connected to the DATA INPUT connector, or cable. Try to "LOAD" again.

∞

Un-formatted indication (The internal hard disk is damaged or not formatted yet.)

After this message is shown for about 10 seconds, "FORMAT" in Setup mode will

flash on the display. Pressing the EXECUTE/YES key at this moment will erase

all data and reformat the hard disk.

Action to take:

Press the EXECUTE/YES key to format the disk. (All audio and other data on the

disk will be lost.)

∞

Disk error indication (This disk cannot be read)

Action to take:

Contact the Fostex service station as soon as possible.

∞

Recording Disable (Recording is disabled.)

Action to take:

Change the "Off" (recording) "Rec Protect ?" setting in Setup mode.

∞

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Names and Functions)

SCSI device connection error: (The SCSI device is not connected correctly.)

Action to take:

Check to see if the external SCSI device is connected to the SCSI connector

correctly, or the power to the SCSI device is turned on.

∞

Disk Lock error: (The hard disk is not installed correctly, or not securely locked by the key.)

Action to take:

Install the hard disk correctly or confirm that the disk is set properly, and be

sure to lock it using the included key.

∞

In rare case, the "No Disk IDE" will also be displayed if the cartride connector

pins are soiled. In such a case, clean the connector pins with alcohol or its

equivalent.

When cleaning, however, be extremely careful not to generate static electricity.

SCSI save error: (Occurrence of an error during execution of save into SCSI equipment)

Action to take:

Because "Retry?" will be displayed when the EXIT/NO key is pressed, if save is to

be executed again, press the EXECUTE/YES key upon display of "Retry?."

If save is to be canceled at this stage, press the EXIT/NO key again.

∞

SCSI load error: (Occurrence of an error during execution of load from SCSI equipment)

Action to take:

Because "Retry?" will be displayed when the EXIT/NO key is pressed, if loading

is to be executed again, press the EXECUTE/YES key upon display of "Retry?."

If loading is to be canceled at this stage, press the EXIT/NO key again.

∞

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

Before Operating the D-160

This section explains the following items that you should learn before you start operating

the D-160.

1. Hard disk recording method and the REMAIN display

2. Audio file and event

3. Program Change function

4. Real track and additional track

5. Input monitor and reproduction monitor

6. Time base

7. Installing and formatting a hard disk

8. Expanding a detachable controller

1. Hard disk recording method and the REMAIN display

The D-90, D-80, and DMT series are able to play back only within a recorded area (ABS 0

- ABS END), but unable to play or fast forward after the record end point (ABS END) as

shown in the diagram below. They can start recording only from the ABS END point.

approx. 30 minutes

(when installing the Model 9041.)

ABS END

ABS 0

D-90, D-80, and DMT series

Non recorded area

ABS TIME: 00m 00s 00f ~ 30m 00s 00f

Play is possible in this area.

On the other hand, the D-160 enables you to select any ABS time position within 24 hours

to record an audio signal on the formatted hard disk. (Refer to the diagram below.)

For example, if you are using an optional Model 9041 (1.3GB removable hard disk

cartridge), you can record about 15 minutes to all 16 tracks anywhere within the range of

24 hours. (The REMAIN display will indicate 240 minutes since the D-160 calculates the

remaining free space based on a mono track.)

10h 05m

00h 05m

10h 00m

Non recorded

area

ABS 0

24h 00m

ABS END

Non recorded area

Recorded area (5 minutes)

ABS time: within 24 hours

The D-160 enables you to select any ABS

time position within 24 hours to record an

audio signal

If you recorded five minutes of 16-track data starting at 00h:00m:00s:00f:00sf (ABS 0),

then recorded another five minutes of data starting at 10h:00m:00s:00f:00sf, the ABS

END point would be at the end of the second recording, 10h:05m:00s:00f:00sf.

This does not mean that the recording on the hard disk is 10 hours 5 minutes long.

The total recorded time on the disk would be 10 minutes (two 5-minute recordings).

In this case, if you try to play the unrecorded area (00h:05m through 10h:00m), the

display will count down the time, but the D-160 will not access the hard disk.

The same applies to the area after the ABS END point. If you try to play or fast forward

in the area after the ABS END point, the display will count down to one frame before 24

hours (based on the frame rate specified in Setup mode).

However, MTC will be output during the playback of an unrecorded area.

In this example, pressing the DISP SEL key will switch to the REMAIN display that

indicates about 80 minutes (based on a mono track). This is a recordable duration when

data is recorded in a single track. As mentioned, above the REMAIN display will indicate

240 minutes when you are using an optional Model 9041 (1.3GB removable hard disk

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

cartridge.) This means that you can record total 240 minutes of data with a sampling

rate of 44.1kHz in a single track.

Recording one-minute, one-track data with a sampling rate of 44.1kHz on the D-160

requires approximately 5.3MB of hard disk space. Therefore, the amount of space required

for a particular recording should be obtained by multiplying 5.3MB by the number of

tracks by the number of minutes (duration). If the REMAIN display indicates 240 minutes

based on a mono track, you can record about 15 minutes of 16-track data. If you have

recorded 10 minutes of 16-track data, you would have used the hard disk space

corresponding to 160 minutes (16 tracks times 10 minutes). The resultant REMAIN value

would be 240 -160 = 80 minutes.

2. Audio file and Event

As described in the previous section “Hard disk recording method and the REMAIN

display,” the basic recording method differs between the D-90/D-80/DMT series and D-

160. The D-160 contains sequential individual audio files recorded in the tracks of a

Program. You can insert silence between these audio files. The silence will be counted as

a zero file. As shown in the diagram below, audio files and zero (0) files will be recorded

alternately.

“The number of events” of a certain track is calculated by adding up the number of these

audio files and zero files. Each track can contain up to 512 events, but the D-160 will not

record new data when the recording reaches the event 508.

ABS 0

ABS END

Audio File 2

0 File 1

Audio File 3

Audio File 4

Audio File 1

0 File 2

No sound

Usually, a single event is created by one recording or editing operation, and the number

of the events changes according to the edit point or the amount of available disk space.

(The D-160’s disk management generally tries to reduce the number of events.)

This does not create problems in most music production. However, if you make frequent

recordings with zero files in between the audio files, the number of the events could

exceed the limit. In order to prevent this, you need frequently to check the number of

events on each track during a session.

Use the “NOs Of Event?” menu in Setup mode to check the number. Refer to “‘NOs Of

Event?’ menu in Setup mode” on page "163."

No “0 file” is created during analog recording, because data 0 will not continue even when

silence is being recorded. On the other hand, if you are recording data via S/P DIF or adat

input, the D-160 will create a zero file when 0 data is consecutively input for one second to

save disk space. This increases the number of events. Watch out for “the excessive number

of events.”

What is an event?

As shown in the diagram below, the number of events can be eleven or more if partial

recordings are made. This is because an unrecorded part is regarded as an event, and a

recorded part is also regarded as an event(s). The duration of each event can vary from

740 msec to 23 hours 59 minutes 59 seconds (FS = 44.1kHz).

Recorded part (shortest: 740 msec, FS=44.1kHz)

Unrecorded part (shortest: 740 msec, FS=44.1kHz)

ABS 23h 59m

ABS 0

ABS END

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

An unrecorded part (zero file) is always regarded as one event, regardless of its duration.

However, a recorded part can consist of a group of multiple audio files, as shown in the

diagram below.

More precisely, one audio file will be divided into multiple audio files if perform many

editing operations (such as, copy & paste, move & paste, etc.) on this audio file. Multiple

audio files created in this way are regarded as events. (If you do not edit the data at all,

the audio file remains in one piece and is regarded as one event.)

In this example, one recorded area consists of six consecutive audio files. This means that

this part consists of six events.

Recorded Area

0 File Audio File 1 Audio File 2 Audio File 3 Audio File 4 Audio File 5 Audio File 6

n + 1 n + 2 n + 3 n + 5

n + 6

0 File

Event Number

n + 4

This is because when you perform a copy & paste, move & paste, or Auto Punch In/Out,

the event is split at the edit point. Also, if a continuous long recording is made, the

recorded data might scatter to different locations on the hard disk, thus dividing the data

into multiple events.

Clipboard In Point

Clipboard Out Point

0 File

Audio File 5 Audio File 6

n + 6

Audio File 1 Audio File 2 Audio File 3 Audio File 4

n + 2 n + 3

n + 5

n + 1

n + 4

Countermeasures against accumulating too many events due to a long recording plus

many editing operations:

One solution is to save and re-load the data to and from a DAT, Adat, or SCSI device. (If

the song is too long, you may not be able to save the data to a DAT or Adat.)

In this way, multiple consecutive audio files are optimized into one continuous audio file

in some cases.

If you know which part of the data you edited, and if the hard disk has enough free space,

you can use another solution in some cases.

Set the Clipboard In point and the Clipboard Out points within an unrecorded range to

copy the area (the area that contains multiple audio files and you wish to optimize)

between them, then paste the data starting from the same Clipboard In point.

Multiple audio files within this range will become a single audio file.

<Hint>

Make sure that you set the Clipboard In/Out points within zero files, and that you paste

the area starting from the SAME Clipboard In point.

* In any case, bear in mind that you cannot reduce the excessive number of events if the

target range contains a zero file.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

3. Program Change function

The D-160 features a Program Change function, which enables you to setup as many as

99 Programs on a single hard disk, and record and edit up to 99 separate songs.

You can also name (title) each Program.

Using an analogy, imagine that each Program has its own room on the hard disk.

You can record, play, and edit each Program without affecting other Programs.

Assume that you have made a six-minute mono-track recording in Program 1, then you

have setup Program 2 and made a 10-minute, mono-track recording to the Program.

Now, the hard disk contains two rooms (total 16 minutes). (You can setup a maximum of

99 Programs.)

Program 2

Program 3

Program 1

Program 4

Program 6

Program 7

Program 5

Program 9

Program 8

Program 10

Program 11

Program 12

Individual rooms (You can setup a maximum of 99 Programs.)

In the default setting, one Program has been setup. If you wish to setup more Programs,

refer to “Recording/Playback, 2-1. Setting up a Program.”

Please remember, however, that regardless of the number of Programs you setup, the

total recording time of the Programs cannot exceed the maximum available time of the

hard disk.

For example, if you are using a Model 9041 (1.3GB), you can record up to about 15

minutes on all 16 tracks (with a sampling rate of 44.1kHz), or up to 240 minutes on a

single mono track. Therefore, if you have already recorded a 15-minute, 16-track song in

Program 1, the available recording time will remain 0, and you will be unable to record

data to other Programs.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

4. Real track and additional track

You can record, play back, and edit up to 16 real tracks on the D-160.

The D-160 also features eight additional tracks.

Real tracks 1-16 are used for recording, playing back, and editing.

Additional tracks 17-24 are used to store data.

More precisely, you can play back and monitor data recorded on the real tracks and

check it with the level meters. But, data stored on the additional tracks cannot be

monitored or checked with the level meters. The purpose of the additional tracks is to

temporarily store the data recorded on the real tracks (1-16).

Track 16

Track 15

Track 14

Example:

Track 13

Exchange data recorded on Track 11 with data recorded on Track 15.

Track 12

Track 11

Track 10

Track 9

Track 24

Track 23

Track 8

Track 7

Track 22

Track 21

Track 20

Track 6

Track 5

Track 4

Track 3

Example:

Swapping between real

tracks 1-8 (or 9-16) and

additional tracks 17-24.

Track 19

Track 18

Track 17

Track 2

Track 1

Additional track

Real track

You can swap data between two tracks (between two real tracks, additional tracks, or

between a real track and a additional track) using the “Track Exchange?” menu in the

Setup mode.

For example, you can exchange data recorded on Track 1 with data recorded on Track 8.

If you swap between a track with data and a track without data, the track that originally

contained data will become empty.

You can also swap data between eight tracks; that is, swapping between real tracks 1-8 (or

9-16) and additional tracks 17-24.)

This is very convenient in a multitrack recording application when you wish to clear

some tracks in order to make new recordings.

For example, if you swap between real tracks 1-8 (or 9-16) with data and additional

tracks 17-24 without data, the real tracks become empty. So, you can make new recordings

in these empty tracks. You can, of course, load back the data from the additional tracks

to real tracks. During the save/load operation, you can also save or load both real track

data and additional track data.

<Notes>

* The D-160 always uses data on real tracks for the ABS END indication.

For example, If you have moved all track data to the additional tracks and the real tracks are empty, ABS END

is “0.” In order to check the ABS END point of the data in the additional tracks, you need to move the data into

the real tracks. Alternatively, you can check the data status of the additional tracks by checking the events on

the “NOs Of Event?” menu in Setup mode. (Refer to page "163" for more information on the “NOs Of Event?”

menu in Setup mode.)

* You cannot swap data between the tracks from two different Programs.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

5. Input monitor and Repro monitor

There are two ways to monitor track data on the recorder: Input monitor and

Repro monitor. These are defined as follows:

Input monitor:

Input monitoring enables you to listen to the input signal that is routed to

and output through the tracks just as it is. That is, listening to (monitoring)

the post-recorder input signal (not the pre recorder signal).

Sixteen tracks on the D-160 can be set to either "Input monitoring" or "

Repro monitoring" status. Follow the steps below to set the tracks to Input

monitor.

1. Set the track to recording status.

To set the track to recording status, first ready the track, then press the PLAY button while

holding the RECORD button. The recording track will be in Input monitoring status.

Alternatively,

2. Ready the track, and press the RECORD button once. (If you press the RECORD

button again, the track enters the repro monitoring status.)

Track 5:

INPUT monitor

Tracks 1-4:

Input signals

Mixer

REPRO monitor

Recorder (D-160)

* The RECORD LED next to the RECORD button will flash, and the currently selected

tracks will enter input monitoring status.

Repro monitor:

Repro monitoring enables you to monitor the playback signal on the tracks;

that is, to listen to the output of the recorded signal.

All tracks:

Mixer

REPRO monitor

Recorder (D-160)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

6. Time Base

The D-160 indicates the location of the recorder (the current position) using

the ABS time, MTC, or MIDI Bar/Beat/Clock. This time reference is called "Time

Base."

ABS (Absolute Time) refers to an absolute time on the hard disk; MTC (MIDI

timecode) refers to a relative time obtained by adding a certain value (MTC

offset value) to the ABS value; and BAR/BEAT/CLK (bar/ /clock) indicates a

position in a song that corresponds to the MIDI Clock/Song Position pointer and

can be created using the internal Tempo Map. (The following diagram shows

the relationship between the three types of time base.)

* Replace all symbols in the text with the quarter note symbol.

ABS 0

DISK END

ABS END

00m, 08s, 00f

00m, 00s, 00f

23h 59m 59s

ABS

001BAR, 1 , 00 CLK

-002BAR, 1 , 00 CLK

BAR/ /CLK

BAR =001BAR, "0404(4/4)"

TEMPO=001BAR, 1 "60( =60)"

0h 59m 59s

01h, 00m, 08s, 00f

01h, 00m, 00s, 00f

MTC

MTC OFFSET=01h, 00m, 00s, 00f

MTC OFFSET MODE = ABS

(THIS shall be assumed to be the

MTC OFFSET time set for the ABS

00m, 00s and 00f positions.)

0h 59m 51s

00h, 59m, 52s, 00sf

01h, 00m, 00s, 00sf

MTC

MTC OFFSET=01h, 00m, 00s, 00f

MTC OFFSET MODE = BAR

(THIS shall be assumed to be the

MTC OFFSET time set for the 00

BAR, 1 and 00 CLK positions.)

Recorded area

Non recorded area

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

7. Installing and formatting a hard disk

The D-160 utilizes a removable hard disk cartridge, making it quick and

easy to transport and replace the hard disk.

Using an optional removable hard disk cartridge Model 9041 (1.3GB hard

disk built-in) or Model 9040B (empty caddy without hard disk) allows you

to replace the cartridge or extend the sixteen tracks recording time very

easily.

* Refer to next page for more information on replacing the removable hard disk cartridge.

You can install an ATA (IDE) standard hard disk in an optional removable case

Model 9040B (without hard disk).

<Note>

Refer to the "Supplement" for more information on "Recommended Hard Disk" and

"Operation-Confirmed hard Disk" lists.

Plug the included dust cap onto the connector of the D-160's removable hard disk to

protect the disk from static electricity, dust and dirt before you store or transport the

hard disk. A hard disk is precision device. Handle it with care and avoid vibration,

humidity, strong magnetic fields, static electricity, dust, etc. In particular, do not touch

the connector with your hands to protect the hard disk from static electricity.

Removable hard disk

Plug the dust cap onto the connector.

(Do not touch the connector with your hands.)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

Installing a removable hard disk cartridge

A hard disk cartridge is not installed in the D-160 when it is shipped. You will need

to install a removable hard disk cartridge in the D-160. (You can use an optional

Model 9041 or a hard disk that has been approved for performance and installed

in the removable case that came with the D-160.)

Follow the procedure below to install a new hard disk cartridge. Be sure to format

the hard disk. The following procedure should be performed with the power to the

D-160 turned off.

1. Remove the blank panel from the cartridge slot.

The unit is

DIGITAL MULTITRACK RECORDER

D-160

POWER

shipped from

the factory

with the lock

on the right

of the slot

released.

Unlock

Do not try to insert your fingers into the removable

hard disk cartridge drive after the cartridge has

been removed. Otherwise, electric shock or

unexpected injury could result.

Blank panel

2. Insert the hard disk cartridge (e.g., Model 9041) into the slot.

Make sure that you insert the cartridge until it clicks into place. Be sure to remove the

dust cap on the connector of the cartridge case before inserting the cartridge.

DIGITAL MULTITRACK RECORDER

D-160

POWER

Model 9041

3. Lock the cartridge with the key included in the package.

DIGITAL MULTITRACK RECORDER

D-160

POWER

Lock

4. Connect the connector of the detachable controller, and install the controller to the D-160.

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

HOLD/

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

* When installation is completed, follow the procedure “Formatting a hard disk” on

page "43" to format the hard disk.

* If you are using a hard disk (that has been approved for performance) and installing

it in the removable case that came in the package, refer to “Installing a hard disk in the

removable case” on page "42."

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

Replacing a removable hard disk cartridge

Follow the procedure below to replace the removable hard disk cartridge.

1. Turn the power off to the D-160.

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

2. Remove the connector from the detachable remote controller section, and remove the

controller section.

3. Release the lock using the key included in the package. (Refer to the figure on the right

below.)

DIGITAL MULTITRACK RECORDER

D-160

POWER

Lock

Do not try to insert your fingers into the removable

Unlock

hard disk cartridge drive after the cartridge has

been removed. Otherwise, an electric shock or

unexpected injury may result.

4. Pull the disk cartridge forward you to remove it.

The hard disk is a precision device. Handle it with care.

5. Insert new disk cartridge.

Gently push it in until a click noise is heard.

6. Lock the cartridge using the key. (Refer to the figure on the right above.)

7. Install the controller section, and fix the connectors securely using the screws.

DIGITAL MULTITRACK RECORDER

D-160

POWER

* When installation is complete, follow the procedure “Formatting a hard disk” on

page "43" to format the hard disk.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

Installing a hard disk in the Model 9040B removable case

If you have purchased one of the hard disks listed in the "Supplement," you need to

install the disk in the included removable case or Model 9040B optional removable case.

Follow the procedure below to install the disk in the removable case, and then

install the case in the D-160 as explained on the previous page, and format the disk.

A hard disk consists of precision parts, and is sensitive to strong shocks (such as being dropped).

Handle the disk with care. Install the disk on a level, stable surface.

Fostex is not responsible for any malfunction or damage caused by incorrect handling.

If any part of the disk unit touches the case bottom, paste an "insulation seal (diameter: 18mm)"

included in the package of the case at the point of contact.

Some disk units may have such a dimension that the part could touch the case. If you use a

disk with a part touching the case, a short circuit, malfunction, or damage could result. Make

sure that no part of the disk touches the case, or paste the seal.

<Note>

Be sure to set the DIP switch or the JUMPER switch on the hard disk to "MASTER" when you

install the hard disk in the removable case. The disk will not operate if the setting is "SLAVE."

(Refer to Hard Disk's Owner's Manual for details.)

1. Disassemble the removable case.

Refer to the diagram to remove the bottom of the case.

Place your figures on the upper part of the case, and

Hold down the case

remove the bottom so that it will open in the direction of

with your hand.

the arrow.

Remove

Bottom

Model 9040B

2. Insert the disk unit into the case, and connect the cable connectors on the case to the

appropriate connectors on the disk unit.

Sometimes it may be difficult or awkward, due to a lack of space, to connect the connectors

when you are installing a hard disk into the removable case. In this event, do not apply

excessive force on the connector. Use caution to avoid injury or damage to the hard disk.

Connect the cable

connector

Handle

Connector

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

3. Secure the disk unit using the screws that come with the removable case. (Use two

screws on each side as shown in the diagram.)

Screws (x4)

4. Replace the bottom. (Before installation, read the following note.)

5. Install the entire case and disk in the D-160 following the steps on page “40” (don't

forget to lock the key!) and proceed to formatting.

Formatting a hard disk

After replacing the hard disk cartridge, follow this procedure to format the disk.

When you turn the power on to a D-160 that has an unformatted disk, the unit

automatically enters the Setup mode "Disk Format?" menu.

1. Confirm that the cartridge is locked by the key, and turn on the power to the D-160.

The display will show the initial screen, then change to the following screen:

"IDE" shown in the display indicates that the internal IDE hard disk is undergoing formatting.

∞

SETUP

FORMAT

44.1kHz

∞

2. After confirming the above display, press the EXECUTE/YES key.

The currently installed internal IDE hard disk model name will be shown in the display

and "SURE?" will blink at the same time.

SETUP

FORMAT

44.1kHz

∞

SURE

3. Press the EXECUTE/YES key again.

Formatting of the internal IDE hard disk will be started and progressive to this, the

remaining unformatted disk capacity will be counted down attached with a minus symbol.

Simultaneous with the start of formatting, the ∞ symbol FL tube in the level meters of all

channels will light. And as formatting progresses, the FL tube will be extinguished one by

one starting from track 16.

This is an indication that the hard disk is being formatted correctly and when formatting

is finished, all FL tubes will be extinguish and "COMPLETED!" will be lit.

SETUP

REMAIN

FORMAT

44.1kHz

COMPLETED

44.1kHz

∞

4. Press the EXIT/NO key or the STOP button to quit Setup mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

* If you are using a hard disk that already contains any data from when it was used

in a computer, the D-160 may not enter formatting mode automatically. In this

case, press the DISP SEL key to force the unit to enter Setup mode, and then

select “Disk Format?” to format the disk. (See page “171” for more information on

“Disk Format?” menu in the Setup mode.)

8. Extending the detachable controller

You can remove the detachable controller from the main unit and extend

it using an optional Model 8551 extension cable.

This optional cable is five meters long, and is equipped with D-sub 15-pin

male and female connectors.

Connect to controller (female)

Connect to D-160 (male)

1. Turn the power off to the D-160 before connecting the cable.

2. Loosen the screw for the connector that connects the controller to the D-160,

and remove the connector.

3. Remove the controller from the D-160.

Pull the controller toward you while pushing it up with your hand to remove it easily.

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

COPY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

4. Insert the male connector of the extension cable to the D-160's connector, and

secure it with a screw.

5. Connect the female connector on the cable and the male connector on the

controller cable, and secure them with a screw.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Before operating the D-160)

DIGITAL MULTITRACK RECORDER

D-160

POWER

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

6. Turn the power on to the D-160, and operate the buttons and keys on the

controller to confirm that the D-160 operates correctly.

When you use the detachable controller remotely using an extension cable, the D-

160 may malfunction due to electromagnetic interference. In this case, turn the power

off, then on to the D-160 to restore it to normal.

Fostex is not responsible for any malfunction of the D-160 that is caused by

electromagnetic interference.

Turn off the D-160 before connecting or disconnecting any cables.

Connecting or disconnecting the footswitch or detachable controller cables while the

D-160 is turned on will cause it to malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

Recording / Playback

This section explains how to record and playback data on the D-160.

1. Basic connections

The D-160 is a 16-track recorder, equipped with analog INPUTs 1-8 and OUTPUTs

1-16. Refer to the following diagram to connect the D-160 to an external mixing

console or multitrack recording.

The optimum mixing console for the D-160 would be equipped with 16 TAPE IN

connectors and 8 BUSS OUT connectors (or GROUP OUT connectors), although you

can also use a mixer with 16 TAPE IN connectors and 4 BUSS OUT connectors.

Refer to the following examples depending on the type of your mixer.

<Example-1>

Connecting a mixer equipped with 16 TAPE IN, 8 BUSS OUT (or GROUP OUT):

This connection allows for 8-track simultaneous recording.

* Connect the mixer TAPE IN 1-16 with the D-160 OUTPUT 1-16.

* Connect the mixer BUSS OUT (or GROUP OUT) 1-8 with the D-160 INPUT 1-8.

D-160

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

INPUT 1 - 8

OUTPUT 1 - 16

BUSS OUT

TAPE IN 1 - 16

(GROUP OUT) 1 - 8

INPUT

External Mixer

Input signals (Guitar, Keyboard or Vocal etc.)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

<Example-2>

Connecting a mixer equipped with 16 TAPE IN, 4 BUSS OUT (or GROUP OUT):

In this example, you would record tracks 1-4 first, then tracks 5-8, 9-12 or 13-16.

* Connect the mixer TAPE IN 1-16 with the D-160 OUTPUT 1-16.

* Connect the mixer BUSS OUT (or GROUP OUT) 1-4 with the D-160 INPUT 1-4 to record

tracks 1-4. To record tracks 5-8 and 13-16, connect INPUT 5-8 instead of INPUT 1-4.

(Using a patch bay allows you to change the connection from the front.)

D-160

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

INPUT 1 - 8

OUTPUT 1 - 16

Patch bay

TAPE IN 1 - 16

BUSS OUT (GROUP OUT) 1 - 4

INPUT

External Mixer

Input signals (Guitar, Keyboard or Vocal etc.)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

2. Default setting on the D-160

Before you start operating the D-160 or proceed to the next step, you may want to

arrange the controls and switches to restore the initial setting so that you will not,

for example, erase important data on a track by using incorrect settings.

In this manual, this procedure is called "setting defaults." For default settings, the

controls and switches should be arranged as shown in the figure below.

Make it a rule to return to these default settings before you proceed to a new step.

* "FORMAT FIRST". You need to format the internal hard disk prior to start recording

if a brand new hard disk drive has been installed. Refer to the explanation of the

"Disk Format?" menu in the Setup mode. We recommend that you format the hard

disk as often as possible before you start fresh recording on it.

However, remember that the format process will erase all of the recorded song

data.

Outline of the Initial Settings:

* Turn all the RECORD TRACK select keys to "SAFE." (Track indication is turned off.)

* Auto Return/Auto Play mode is "OFF." (The AUTO RTN/AUTO PLAY LEDs are off.)

* Auto Punch mode is "OFF." (The REHEARSAL/TAKE LEDs are off.)

* The STOP button LED is lit.

* The STORE key and the RECALL keys are "OFF." (The STORE/RECALL LEDs are off.)

* "Rec Protect?" is "Off" selected in Setup mode.

* "Digi. In?" is assigned to "L: - -, R: - -" in Setup mode.

* "Slave Mode?" is "Off" selected in Setup mode.

* Setting a Program for recording/playback (See 2-1, 2-2, 2-3.)

* Setting a sampling rate for recording/playback (See 2-4.)

* Turning off the Vari-pitch function. (The LED is turned off.)

* The LED of the SHIFT key is off.

When the Recording Enabled/Disabled parameter in the Setup mode is set to "DISABLE

rEc," pressing the RECORD button and the PLAY button will not start recording, and

the unit will display "DISABLE rEc" on the panel. Be sure to set the mode to "EnAbLE

rEc" to enable the recording function.

Auto Punch mode is "OFF." (The

REHEARSAL/TAKE LEDs are off.)

Auto Return/Auto Play mode is "OFF." (The

AUTO RTN/AUTO PLAY LEDs are off.)

The STORE key and the

RECALL keys are "OFF." (The

STORE/RECALL LEDs are off.)

The display Time Base is set to ABS

TIME, and Program P1 is selected.

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

Turn all the RECORD TRACK

select keys to "SAFE." (Track

indication is turned off.)

Turning off the Vari-pitch function.

(The LED is turned off.)

The STOP button LED is lit.

The LED of the SHIFT key is off.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

2-1. Setting a Program

As explained in the "Before Operating the D-160," the D-160 features a Program

Change function that enables you to manage up to 99 individual Programs.

This means that you need to select a desired Program to work on before you start

recording or playing back.

When you format the hard disk, the D-160 offers one Program (P01) as a default

setting. Follow the procedure below to setup new Programs (up to 99) to manage

each Program using various operations, including the Program Change function.

Program setup procedure

1. Press the STORE key while holding down the HOLD/> key.

The D-160 will enter Program setup mode. The "Select PGM!" indication will

appear, and then the current Program number ("01" by default) will flash.

PGM

44.1kHz

SURE

∞

EXECUTE

/YES

EXIT

/NO

DISP SEL

2, 3

TIME BASE SEL

HOLD/ STORE

RECALL

PGM

PGM CHANGE

44.1kHz

SURE

∞

2. Rotate the JOG dial clockwise. When "New Program?" appears ("?" flashes),

press the EXECUTE/YES key.

When a new Program (P02 in this example) is setup, the D-160 enters the "Title

Edit" menu in Setup mode. The following indication will appear.

PGM

44.1kHz

∞

SURE

PGM

44.1kHz

SURE

∞

3. Press the EXECUTE/YES key. A default (temporary) name for Program 2

(P02) appears and "#" flashes to the left of the title.

If you wish to use a temporary name as it is, press the EXECUTE/YES key to setup

the Program.

If you wish to change the title, refer to page "147" for an explanation of the "Title

Edit?" menu in Setup mode. You can also change the title later.

SETUP

44.1kHz

∞

Repeat the procedure described above to setup as many Programs as you need

(up to 99). Each time you setup a new Program, the Program will be assigned the

subsequent Program number. For example, if you setup a new Program after you

have set five Programs (P01~P05), the new Program number will be 6. You cannot

skip numbers.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

2-2. Program Change

The Program Change function allows you to manage multiple Programs that were setup

according to the procedure mentioned above for the recording, playback, or editing of

the individual Programs. The D-160 needs to be in the Program Setup mode to perform

the Program Change function.

The following example assumes that ten Programs (P01 - P10) have already been setup.

Program Change procedure

1. Press the STORE key while holding down the HOLD/> key.

The D-160 will enter the Program Setup mode, and displays “Select PGM!”, and then the current

Program number and title.

2. Use the JOG dial to select a desired Program.

Rotating the JOG dial back and forth will change the Program number on the display to a smaller

or larger number.

For example, rotating the JOG dial counter-clockwise when P03 is selected will change the Program

number on the display as follows: P03 --> P02 --> P01. Rotating the JOG dial clockwise will change

the Program number as follows: P03 --> P04 --> P05 ..... --> P10 --> New Program?.

If you wish to setup a new Program, select the “New Program?” indication.

P01

P02

P03

P08

New Program?

P09

P10

Current Program

A selected Program uses the Time Base (ABS, MTC, or BAR/BEAT/CLK) that was used

for the Program previously. To change the Time Base, press the DISP SEL key while

holding down the EXECUTE/YES key. You can set the Time Base for each Program.

Pressing the DISP SEL key will display the REMAIN indication. Use this indication to

check to see if any available recording time (or bars) remains. This remaining time is

not the time for the corresponding Program, but the total amount of time that can be

used by all Programs. Bear in mind that the REMAIN indication is based on the mono

track calculation.

<Note>

1. The following parameters can be set for each Program individually:

Memory data (CLIPBOARD IN/OUT, AUTO RTN START/END, AUTO PUNCH IN/OUT)

Time Base (ABS, MTC, or BAR/BEAT/CLK)

SETUP mode:

* Time signature setting (BAR BEAT), * TEMPO setting, * CLICK ON/OFF setting,

* PREROLL TIME setting, * MIDI SYNC OUT setting, * MTC FRAME RATE setting,

* MTC OFFSET setting, * MTC OFFSET MODE setting, * REC PROTECT ON/OFF setting,

* SLAVE MODE ON/OFF setting, * SLAVE TYPE setting, * FS (Sampling frequency) setting

2. The following parameters are common to all Programs:

Auto Play mode ON/OFF, Auto Return mode ON/OF, Vari-pitch mode ON/OFF, Pitch

data

SETUP mode:

* DIGITAL IN setting, * DIGITAL OUT setting, * BAR/BEAT RESOLUTION ON/OFF setting,

* DEVICE ID setting

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

<Note>

The total available time for recording data in the existing Programs (up to 99) equals the

available recording time on the hard disk.

For example, if you are using an optional Model 9041 (1.3GB removable hard disk cartridge),

you can record about 15 minutes (with a sampling rate of 44.1kHz) to all 16 tracks. Therefore,

if you have already recorded 5-minute, 16-track song in Program 1, the available recording

time for other Programs would be about 10 minutes. In other words, regardless of the

number of Programs used, you can record up to 15 minutes in total.

Bear in mind that the REMAIN indication is based on a mono track.

2-3. Deleting a Program

You may delete an unnecessary Program using the “Delete PGM?” menu in Setup mode.

You can delete a Program that is currently selected with the Program Change function.

Follow the procedure below:

Program delete procedure

1. Select a Program to delete with the Program Change function.

Refer to the “2-2. Program Change function” section.

2. Press the DISP SEL key to enter Setup mode, and use the JOG dial to select

the ‘Delete PGM?” menu.

3. Press the EXECUTE/YES key twice to execute the delete operation.

Refer to page "147" for more information on the “Delete PGM?” menu in Setup mode.

<Note>

After a Program is deleted, the D-160 will display the current Time Base (ABS/BAR BEAT/

MTC) of another Program that now has the number of the deleted Program.

This is because Program number are automatically updated.

For example, if you delete Program 5 out of Programs 1-10, Program 6 will become Program

5, and the subsequent Program numbers will be updated. The titles are also updated. (That

is, Program 6 now becomes Program 5, with the title for Program 5, and the subsequent

Program titles are updated.)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

2-4. Setting a Sampling Rate

The D-160 supports two sampling rates: 44.1kHz and 48kHz.

Before you start recording data in a new Program, be sure to set the sampling rate,

using the procedure below. After you format the disk or set up a new Program, the

sampling rate is set to “44.1kHz.” If you wish to use this rate, you do not have to

follow the procedure below.

The sampling rate of the Program is indicated by the status of the 48kHz message

above the display. The message lights up at a setting of 48kHz, and is turned off at

a setting of 44.1kHz.

* Default: 44.1kHz

* Available sampling rates: 44.1kHz, 48kHz

* This parameter can be set for each Program.

* This setting can be saved and loaded as part of the song data.

* This setting will be retained after the power is turned off.

* Check to make sure the correct Program has been selected before you set the sampling rate.

* Refer to page "162" of " Setup mode 2-19. Sampling Frequency Setting" for

information on operating procedures.

The sampling rate setting does not greatly affect analog recording or playback.

However, it can be an important element when the D-160 is processing a digital signal.

For example, CDs use a sampling rate of 44.1kHz, and you will need to set the sampling rate

of the D-160 to 44.1kHz for digital recording from a CD. If you have set the sampling rate on

the D-160 to 48kHz when recording from a CD, the 48kHz message located above the display

will flash to warn you. When you work with a 48kHz digital signal input from an adat, set the

sampling rate to 48kHz.

Also, make sure that the sampling rate of any external device matches that of the D-160 when

a digital signal is output from the D-160 to an external device, such as a digital mixer.

<Note>

A 48kHz sampling rate setting requires more disk space than a 44.1kHz setting.

This means that the available recording time will be shorter.

Therefore, the remaining disk space (REMAIN) after recording with a sampling rate of

48kHz would be smaller (shorter in time).

<Note>

Do not change the sampling rate of a Program during a session unless it is very

important. It is possible to change the sampling rate setting, but the Program will be

played back at a speed different from the original recording speed, causing the data

value stored in the Memory keys (time, or bar/beat/clock) to change.

* Refer to page "60" for information on recording and playback of a digital signal.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

3. Analog Recording and Playback

This explanation is based on the assumption that the D-160 is connected to a

mixer, and the sound source is input from the mixer’s BUSS OUT (GROUP OUT)

connector, as shown in the “1. Basic Connection” section.

* Restore the default settings on the D-160.

* Check the Program selection and the sampling rate setting. Do not change these settings until this

session is complete.

3-1. Basic recording and playback

Assume that “P01” has been selected for recording.

If you wish to record data in another Program, see the section 3-2.

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

1,5

Turn on the power to the D-160, and check to make sure that the Time Base display

indicates ABS time “00m 00s 00f” and “P01”.

Selecting a recording track

1. Press any RECORD TRACK select key (1-16) to "READY" the track.

The number of the selected track will blink on the display.

Adjusting the recording level

The D-160 does not have a recording level control. You need to adjust the recording

level on a connected device that sends out sound data. Primarily use the GROUP

OUT master faders (or the faders that control the output level of BUSS OUT 1-16)

on the mixer. The recording track of the D-160 also needs to enter input monitoring

status.

2. Press the RECORD button once.

The READY track enters input monitoring status. Raise the GROUP OUT master fader on

the mixer so that the meter of the "READY" track approaches level "0-3" at peak volume.

If the "OL" indication is lit, the recording level is too high.

Unlike an analog recorder, if the recording level is too high, the signal may be distorted on

a digital recorder. In particular, recording vocal or acoustic musical instruments requires

more attention because the recording level may change suddenly, causing signal overflow.

It may be a good idea to use a compressor/limiter connected to an INSERT connector on

the mixer.

Start recording

3. After adjusting the recording level, press the RECORD button while holding down the

PLAY button.

The blinking RECORD LED and track indicator will light up.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

4. To stop recording, press the STOP button.

"Please Wait!" will be shown in the display while the post recording process is in progress.

Playback

5. Press the "READY" track's RECORD TRACK select key to switch to "SAFE." (The track

indicator will turn off.)

6. Press the STOP button and the REWIND button simultaneously to locate the beginning

of the Program (ABS 0).

7. Press the PLAY button.

The recorder will start playback data. Adjust the TAPE IN input level on the mixer while

monitoring.

In this way, you can record sound source to any track (a single track or multiple

tracks).

3-2. Recording with the Program Change function (Switching Programs P01-P99)

As previously explained, the D-160 has a "Program Change Function" to manage

up to ninety-nine songs. You can record, playback, and edit each Program separately.

This section explains how to record and play back Programs using the Program

Change function.

* Restore the default settings on the D-160.

Changing a Program

1. Set the Program to be recorded.

Select the desired Program by referring to the previous "2-2. Program Change."

When you select a Program, the Time Base setting (ABS, MTC, or BAR/BEAT/CLK)

you used previously for that Program will be used again.

To change the Time Base display, Press the DISP SEL key while holding down the

EXECUTE/YES key. You can set the Time Base for each Program individually.

You can also switch to the REMAIN indication by pressing the DISP SEL key.

Check to see if there is enough time (bars) remaining for recording.

This value is not an available time for each Program, but the total available time

for all Programs.

2. Set the sampling rate if necessary.

Refer to section “2-4. Setting a sampling rate” for the correct procedure.

Recording (Refer to “3-1. Basic recording/playback” for details.)

3. Press the RECORD TRACK select key (1-16) to set the recording track in ready mode.

4. Press the RECORD button once to set the unit in input monitoring status, and adjust the

recording level.

5. Press the RECORD button while holding down the PLAY button.

6. When recording is complete, press the STOP button.

"Please Wait!" will be shown in the display while the post recording process is in progress.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

Playback (Refer to “3-1. Basic recording/playback” for details.)

7. Press the RECORD TRACK select key for the track in ready mode so that the track

becomes “safe.”

The track LED will be turned off.

8. Press the REWIND button while holding down the STOP button to locate the top of the

Program (ABS 0) (LOCATE ABS 0).

9. Press the PLAY button.

Playback will start. Adjust the TAPE IN input level from the mixer.

<Note>

The maximum total recording time of all nine Programs equals the available recording

time of the hard disk. For example, if you use the optional Model 9041 (1.3GB

removable hard disk cartridge), the available recording time is about 15 minutes

(with a sampling rate of 44.1kHz, 16 tracks recording). If you have recorded 5 minutes

of data in Program 1, you can record 10 minutes for the total time of another Programs.

That is, you can record data totalling 15 minutes, regardless of whether you use up all

Programs or you record only one Program. Therefore, the remaining recording time

is obtained by subtracting the sum of the recorded time for all recorded Programs

from the initial total available time.

This remaining time is indicated as the REMAIN time when you press the DISP SEL

key. Be sure to watch this time when you are recording multiple Programs.

<Note>

Data with a sampling rate of 48kHz uses more hard disk space than data with a sampling

rate of 44.1kHz. Therefore, the available recording time is shorter for 48kHz data.

* Refer to “2-1. Setting a Program” and "2-2. Program Change" for more information

on Programs.

* Refer to “2-4. Setting a sampling rate” for more information on sampling rates.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

3-3. Playback using the Vari-pitch function

This section describes how to use the Vari-pitch function to change the playback

speed of the recorder. The D-160’s Vari-pitch function allows for pitch control in

the range of +/-6.0% in 0.1% steps.

Use the VARI PITCH key to switch the Vari-pitch function on/off. The LED lights up

when the function is enabled, and the LED is off when the function is disabled.

* Restore the default settings on the D-160.

* Check the Program selection and the sampling rate setting. Do not change these settings until this

session is complete.

* Assume that a Program has already recorded track according to the procedure described in

“3-1. Basic Recording and playback.”

1. Press the PLAY button to start playback.

2. Press the VARI PITCH key.

The LED will light up, indicating that the Vari-pitch function is on.

3. Press the RECALL key, and then the VARI PITCH key. ("%" indicator will blink.)

The current pitch data will be indicated on the display. You can now edit the pitch data.

44.1kHz

∞

4. Use the JOG dial to edit the pitch data.

You will notice a change in the playback speed.

5. Press the EXECUTE/YES key, the EXIT/NO key, or the STOP button to quit the pitch data

screen.

The screen will return to the Time Base display.

You can turn the Vari-pitch function on and off and change the pitch data while

the D-160 is playing back or stopped, but not while the it is recording.

If the Vari-pitch function is on and the pitch data is set before recording starts,

that speed will be used during recording.

While the pitch data is shown on the display, you can turn the function on and off

and edit the pitch data. However, the PLAY button, or the combination of the PLAY

button and the RECORD button, will be disabled. If you wish to change the pitch

while you are listening to the sound, first press the PLAY button to start playback,

and then display the pitch data indication to change the speed.

<Note>

When you press the VARI PITCH key, the VARI PITCH LED will light, even if the pitch

data is set to 0.0%. The LED indicates that the Vari-pitch function is turned on.

<Note>

The Vari-pitch function will automatically turned off under the following conditions:

* When you turn off the power to the unit. (The pitch data will be reset to 0.0%.)

* When you set the Slave mode to On. (The Vari-pitch function will retain the pitch

data.)

* When you set up a digital input track and the DIGITAL indication on the display

lights up. (The Vari-pitch function will retain the pitch data.)

* If you have installed an optional Model 8345 TC/SYNC card on the D-160 and you

have set the “Word Out?” menu in Setup mode to “8345,” the Vari-pitch function is

turned on even during digital input via DIGITAL IN.

* Refer to page "123" for more information on Slave mode.

* Refer to page "60" for more information on digital signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

3-4. Multitrack recording using overdubbing

You have mastered basic recording/playback in the previous section.

In this section, we will make a multitrack recording.

Multitrack recording is a series of operations in which you record sound sources to

multiple tracks and combine these recordings into two mixes (L, R). In this process,

the most important step is "overdubbing." "Overdubbing" means recording a new

sound source to another track using input monitoring, while listening to the playback

of the pre-recorded sound (that is, playback monitoring).

The following is an example of an overdubbing procedure:

Step 1: Record a drum machine to Track 1

Step 2: Overdub an electric bass to Track 2 while listening to Track 1

Step 3: Overdub an electric lead guitar on Track 3 while listening to Track 1 and 2

Step 4: Overdub an electric side guitar on Track 4 while listening to Track 1, 2 and 3

In this way, we will overdub sound a sources to Track 1 through 16 as shown in the diagram below.

Track 1

Track 2

E. Bass

Track 3

Track 4

..........

Track 16

Synth.

Track 14

Vocal 2

Track 15

Piano

Drum

E. Guitar

...........

Machine

* Restore the default setting on the D-160.

* Stay in the same Program until you finish overdubbing.

* Check the Program selection and the sampling rate setting. Do not change these settings until

this session is complete.

Selecting a recording track

1. Press the RECORD TRACK select key of an overdub track to "READY" the track.

For example, if you are overdubbing Track 2 while listening to Track 1, set the RECORD

TRACK select key "2" to "READY." (Number "2" will blink.)

Adjusting the recording level (rehearsal)

2. Press the RECORD button once. (The RECORD LED will blink.)

The "READY" track will enter input monitoring mode, and "SAFE" tracks will enter playback

monitoring mode.

3. Press the PLAY button to play back data from the beginning of the program (ABS 0).

Adjust the playback monitoring level of the "SAFE" tracks, and play a musical instrument

while adjusting the GROUP OUT level on the mixer, that is, a recording level on the

recorder.

4. Rewind data to the beginning of the disk by Pressing the STOP button and the REWIND

button simultaneously.

Start overdubbing

5. Press the RECORD button while holding down the PLAY button.

Recording will start, and the RECORD LED and the "READY" track indicator will light.

6. Play the instrument while listening to the playback as you did during rehearsal.

7. When recording is complete, stop the recorder, and locate the beginning of the data.

Playback

8. To prevent accidental recording, switch the RECORD TRACK select key of the "READY"

track to "SAFE."

9. Press the PLAY button to start playing back the recording.

On the mixing console, adjust the playback monitoring level of the already recorded

tracks and newly recorded track.

Repeat the steps described above to overdub Tracks 1 through 16.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

3-5. Mixdown

Mixdown is the final step in multitrack recording and allows you to combine multiple

track recordings to L and R channels (two mixes), and copy the data to a master

recorder. The mixdown signal is output from the mixer STEREO OUT L/R connector.

Connect the Inputs of the master recorder to the STEREO OUT L/R.

* Set the D-160 to the default setting.

* This manual assumes that you have already recorded sound sources to all sixteen tracks.

* Refer to the mixer instruction manual for applying effects.

* Connect the master recorder to the mixer STEREO OUT L/R as shown in the diagram.

D-160

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

COPY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

INPUT 1 - 8

OUTPUT 1 - 16

TAPE IN 1 - 16

Master

INPUT L/R

Recorder

BUSS OUT 1-8

STEREO OUT L/R

External Mixer

Mixdown rehearsal

1. Confirm that all the RECORD TRACK select keys are set to "SAFE."

2. Locate the beginning of the sound data on the recorder. (Press the STOP button and

the REWIND button simultaneously.)

3. Set the master recorder to REC-STANDBY mode.

4. Press the PLAY button on the D-160 to play back recordings, adjust the tonal quality

and mix balance of the playback sound on the mixer channels, and adjust the recording

level on the master recorder.

Adjust the input level of the master recorder so that the mixer STEREO OUT L/R meters

and the level meters of the master recorder move in the same manner.

5. Locate the beginning of the program (ABS 0).

Mixdown

6. Start recording on the master recorder.

7. Press the PLAY button on the D-160 to start playback.

8. When mixdown is complete, press the STOP button to stop the D-160.

Stop the master recorder, and listen to the mixdown song.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording /Playback)

3-6. Ping-pong recording

This section explains how to perform ping-pong recording.

Ping-pong recording enables you to combine multiple recorded tracks and copy

them to an empty track. You can then overdub additional sounds onto the

previously-recorded tracks, adding instrumentation or musical parts to your

recording.

* In this example, we are going to ping-pong Tracks 1 through 6 to Tracks 9 and 10.

Since effects cannot be applied to each sound individually after ping-pong recording, we need

to apply effects here on the mixer and record the effect sound to Tracks 9 and 10.

* Set the D-160 to the default setting.

* Check the Program selection and the sampling rate setting. Do not change these settings until

this session is complete.

Track 16

Track 15

Track 14

Track 13

Track 12

Track 11

Track 10

Track 9

Track 8

Track 7

Ping-pong recording

Track 6

(Original signal and

Track 5

Track 4

Track 3

Effected signal)

Track 2

Track 1

Selecting a recording track

1. Press the RECORD TRACK select keys 9 and 10 to "READY" Tracks 9 and 10.

Level adjustment/Rehearsal

2. Press the RECORD button once. (The RECORD LED will blink.)

Tracks 9 and 10 enter input monitoring status.

3. Press the PLAY button to start playback.

Use the mixer to send the signal in Tracks 1-6 to Tracks 9 and 10 and adjust the recording

level.

4. After rehearsal is complete, locate the beginning of the program (ABS 0).

Actual ping-pong recording

5. Press the RECORD button while pressing and holding down the PLAY button to start

ping-pong recording.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording/Playback)

4. Digital Recording

4-1. Digital recording from an external digital device

This section explains how to record a digital signal from the digital output of an

external digital device (CD, MD, DAT, Fostex RD-8, CX-8, etc.) to the D-160.

* Restore the default settings on the D-160.

Connecting an external digital device

Connect the DATA INPUT connector of the D-160 with the digital output of an

external digital device (CD, MD, DAT, Fostex RD-8, CX-8, etc.).

<Note>

The D-160 switches the DATA INPUT connector between an S/P DIF digital signal

(OPTICAL) and an adat digital signal during setting of the digital input track in Setup

mode. Both signals use the same connector configuration, but carry different data.

When S/P DIF digital signals are to be input, DATA INPUT 1-8 only should be used, and

when "adat" digital signals are to be input, either DATA INPUT 1-8 or 9-16 must be

used.

D-160

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

TO RAIN OR MOISTURE.

AVIS

ANALOG OUT

ANALOG IN

3 2

DATA

1~8

SCSI

MIDI

OPTICAL

INPUT

9~16

OUTPUT

9~6 1~8

INPUT

OUTPUT

THRU

DATA INPUT1-8

DATA INPUT1-8 or 9-16

Digital Out (S/P DIF)

adat Out

External Digital Equipment

As shown in schematic below, if "adat" digital signals are simultaneously input from

two individual "adat" equipment, it will be the cause of noise.

Therefore, at input of "adat" digital signals, be sure that the 16 channel output from

the same equipment or the two "adat" outputs from perfectly word locked two separate

equipment, are input. If both "adat" (DATA INPUT 1-8 or 9-16) are connected, phase

will be synchronized at each press of the STOP button to compensate for phase drift.

Also, during this period, DATA INPUT 9-16 will be muted for about 0.5 seconds.

D-160

DATA INPUT 9-16

DATA INPUT 1-8

adat

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording/Playback)

* If the external device has only a coaxial (RCA) type digital output connector, use the

optional COP-1 optical/coaxial converter to connect the device to transmit an S/P DIF

digital signal. The operation is the same as that for a device with a coaxial connector.

* If you connect both the digital input and output of the D-160 to those of an external

digital device, a digital loop may be generated. Refer to “4-3. Connecting a digital mixer”

for more information.

Setting an external device

Set the external device so that it will output digital signals from the digital output

connector. Some devices may output digital signals only when they are in playback

mode.

* Refer to the instruction manual that came with the external device for details.

Selecting a recording Program

Selecting the recording Program.

Refer to "2-2. Program Change" section for more information.

* Refer to “2-1. Setting a Program” ," 2-2. Program Change" and "2-3. Deleting a

Program" for more information on Programs.

Setting the sampling rate for a recording Program

*****IMPORTANT*****

When an S/P DIF digital signal is input to the D-160, be sure to match the sampling rate

of the D-160 to that of the external digital device.

* If the sampling rate settings do not match, you cannot record the S/P DIF digital

signal.

* For an adat digital signal, the D-160 will be able to record data with a different sampling

rate setting. However, the data will be recorded at a different speed. The D-160 will

lock to the external word clock when S/P DIF or adat digital signals are input to the

digital input tracks. (The D-160 will operate, referencing to the word clock sent from

the external device.) However, an adat digital signal does not contain the sampling rate

information (48kHz or 44.1kHz) that is included in the S/P DIF digital signal. This is

why the D-160 can sync to the external device with a different sampling rate.

* Initial setting: 44.1kHz

* Sampling rate settings: 44.1kHz, 48kHz

* This parameter can be set for each Program.

* The setting can be saved and loaded as part of the song data.

* This setting will be retained after you turn off the power.

* Refer to “2-4. Setting a sampling rate” on page "52" for information on how to set

the sampling rate of the selected Program.

After setting the sampling rate, press the DISP SEL key to display the REMAIN

indication and check the remaining time available for recording.

If there is not enough time for recording, try to increase the time by using the

Erase function to move the ABS END point of another Program forward, or by saving

the song data of Programs that are not often used to a DAT machine to clear that

data from the unit.

<Note>

A 48kHz sampling rate setting requires more disk space than the 44.1kHz setting.

This means that the available recording time would be shorter.

* Refer to page "96" for more information on the Erase function.

* Refer to page "102" for more information on saving song data.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording/Playback)

Setting up a digital input track

Set the input tracks according to the type of digital signal selected in “Digi. In ?”

menu in Setup mode. In the following setup items, Lch=1~16 and Rch=1~16 are

inputs of S/P DIF digital signals and will be input only from DATA INPUT 1-8.

At input of "adat" digital signals, signals from DATA INPUT 1-8 and DATA INPUT 9-

16 will be respectively input to ch1~8 and ch9~16.

* Initial setting: L - - R - - (No assignment for both L and R)

* Options: Lch = 1~16, adat, - - (no assignment), Rch = 1~16, - -(no assignment)

* This parameter is common to all Programs.

* This parameter setting cannot be saved or loaded as part of the song data.

* This parameter settings will be retained after the power is turned off.

* Refer to “2-15. Digital input track setting" on page "157" for more information on

the procedure and details.

<Note>

* Tracks assigned for digital input will accept only a digital signal, not an analog signal.

When this system is to be used with the digital input track set to "adat", because an

analog signal can be input to the data track not connected, a digital 8 track and analog

8 track can be simultaneously recorded. For example, if DATA INPUT 1-8 are used and

DATA INPUT 9-16 are not connected, analog signals can be input in the analog input 9-

16 connector.

* This setting will automatically disable the Vari-pitch function (the LED will be turn

off).

* Do not remove the optical cable or perform any other operation that would disconnect

the digital signal until the session is complete. Otherwise, the D-160 will generate noise,

and affect the connected device.

* Do not set the input mode to a different setting during input of "adat" digital signals.

It could result in abnormal input/output of the digital signals.

Selecting a recording track

Press the RECORD TRACK select key of the recording track to set that track in ready

mode.

Recording

1. Press the REWIND button while holding down the STOP button to locate the top of the

Program (ABS 0) (LOCATE ABS 0).

2. Confirm that the “DIGITAL” indicator on the display is lit in red, and press the RECORD

button while holding down the PLAY button to start recording.

You do not need to adjust the recording level in digital recording.

3. Start playing back on the external digital device.

Check to see if the level meter of the D-160 is moving, responding to the input signal.

4. When recording is completed, stop the D-160 and the external device.

<Note>

If you do not perform further digital recording, set the L and R channel assignments to

“- -” (no assignment). This will prevent an interrupted signal or the occurrence of

noise due to digital looping.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording/Playback)

4-2. Digital recording to an external digital device

This section explains how to record a digital data from the D-160 to an external

digital device

* Restore the default settings on the D-160.

Connecting an external digital device

Connect the DATA OUTPUT connector of the D-160 with the digital input of an

external digital device.

<Note>

The D-160 switches the DATA OUTPUT connector between the S/P DIF digital signal

(OPTICAL) and the adat digital signal during setting of the digital input track in Setup

mode. Both signals use the same connector configuration, but carry different data.

When S/P DIF digital signals are to be output, DATA OUTPUT 1-8 only should be used,

and when "adat" digital signals are to be output, either DATA OUTPUT 1-8 or 9-16 must

be used.

D-160

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

TO RAIN OR MOISTURE.

AVIS

ANALOG OUT

ANALOG IN

3 2

DATA

1~8

SCSI

MIDI

OPTICAL

INPUT

9~16

OUTPUT

9~6 1~8

INPUT

OUTPUT

THRU

DATA OUTPUT1-8

DATA OUTPUT1-8 or 9-16

Digital In (S/P DIF)

adat In

External Digital Equipment

* If the external device has only a coaxial (RCA) type digital output connector,

use an optional COP-1 optical/coaxial converter to connect the device to transmit

an S/P DIF digital signal. The operation is the same as that for a device with a

coaxial connector.

* If you connect both the digital input and output of the D-160 to those of an

external digital device, a digital loop might be generated.

Refer to “4-3. Connecting a digital mixer” for more information.

Selecting a playback Program

Selecting the playback Program.

Refer to "2-2. Program Change" section for more information.

* Refer to “2-1. Setting a Program” , "2-2. Program Change" and "2-3. Deleting a

Program" for more information on Programs.

Setting the sampling rate for a playback Program

You need to set the sampling rate of a playback Program to match that of the

digital device before recording digital data.

*****IMPORTANT*****

When a digital signal is output from the D-160, be sure to match the sampling rate of the

external digital device to that of the D-160. If the sampling rate setting does not match,

you cannot record the S/P DIF digital signal and noise may be generated.

Refer to “2-4. Setting a sampling rate” for more information on how to check the sampling

rate of the selected Program. You can also check the rate via the 48kHz indicator located

above the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording/Playback)

Setting up a digital output track

Set the output tracks according to the type of digital signal selected in “Digi. Out ?”

in Setup mode. In the following setup items, Lch=1~16 and Rch=1~16 are outputs

of S/P DIF digital signals and will be output only from DATA OUTPUT 1-8.

At output of "adat" digital signals, signals from DATA OUTPUT 1-8 and DATA

OUTPUT 9-16 will be respectively output to ch1~8 and ch9~16.

* Refer to “2-16. Digital output track setting in Setup mode” on page "159" for more

information on the procedure and details.

* Initial setting: adat

* Options: L ch=adat, ch1~16, R ch= ch1~16

* This parameter is common to all Programs.

* This parameter setting cannot be saved or loaded as part of the song data.

* This parameter settings will be retained after the power is turned off.

* All tracks including tracks specified for digital output also output analog signal.

Setting up an external device

Set the external device so that it will accept a digital signal. On some devices, you

may need to set it so that the device will synchronize to the input digital signal.

For example, if you are using a Fostex RD-8, select “DIGITAL IN” for input, and set

“Clock Source” (external sync signal) to “Word Optical (adat).”

<Note>

When you are monitoring the digital signal from the external device and a signal cannot

be input or digital noise is generated, check the connection, cabling, and settings on the

D-160 and the external device.

* Refer to the instruction manual that came with the external digital device for more

information.

Recording

1. Press the REWIND button while holding down the STOP button to locate the top of the

Program (ABS 0) (LOCATE ABS 0).

2. Start recording on the external device.

You do not need to adjust the recording level in digital recording.

3. Press the PLAY button to start playing back on the D-160.

Check to see if the level meter of the external device is moving, and responding to the

input signal.

4. When recording is complete, stop the D-160 and the external device.

<Note>

* Do not remove the optical cable or perform any other operation that would disconnect

the digital signal until the session is complete. Otherwise, the D-160 will generate noise,

and affect the connected device.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording/Playback)

4-3. Connecting a digital mixer

***** About Digital Loop *****

As shown in the figure, connecting the input and output connectors of the D-160 to

the output and input of a digital mixer respectively may cause digital looping.

When you select a digital input track, the D-160 will automatically enter “sync to the

external word clock in digital input signal” mode. If you set the connected digital

mixer to the same condition (that is, “sync to the external word clock in digital input

signal” mode), both devices will try to lock to the external word clock, resulting in a

digital loop that prevents synchronization from being established.

To avoid this situation, follow one of the suggestions below, depending on the type

of the connected mixer.

DIGITAL IN

DATA OUT

Digital Mixer

D-160

DIGITAL OUT

DATA IN

LOOP

A. Using a digital mixer that accepts a digital signal if you select its internal clock as sync source:

The mixer is always able to input and output a digital signal to and from the D-160.

Select an appropriate digital signal to input in the “digital input track” parameter on

the D-160. The D-160 will lock to the external word clock.

B. Using a digital mixer that locks to the external clock when you select digital input on the D-160:

You need to change the settings on both devices. If you wish to input a digital signal

to the D-160, select an appropriate digital signal to input in the “digital input track”

parameter. You cannot select “digital in” on the digital mixer. On the other hand, if

you wish to input a digital signal to the digital mixer, select “digital in” on the digital

mixer, and set the “digital input track” parameter of the D-160 to “L-- R--” (no

assignment).

This section uses a digital mixer as an example, but the same problem applies to any

other digital device. Any digital device (DAT, adat, etc.) can replace the digital

mixer in this explanation.

The precaution described above applies to a system in which both the input and

output of the D-160 are connected to the output and input of the external device

respectively. If you connect either one of them (output or input), the device that

accepts the input signal will lock and sync to the output device.

The example here uses a digital mixer that can accept a digital input signal when

its internal clock (INTERNAL) is selected.

Connecting a digital mixer

Connect the DATA INPUT of the D-160 to the digital output jack of the digital mixer, and

the DATA OUTPUT of the D-160 to the digital input jack of the mixer.

D-160

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

TO RAIN OR MOISTURE.

AVIS

ANALOG OUT

ANALOG IN

3 2

DATA

1~8

SCSI

MIDI

OPTICAL

INPUT

9~16

OUTPUT

9~6 1~8

INPUT

OUTPUT

THRU

DATA INPUT (1-8 or 9-16)

DATA OUTPUT (1-8 or 9-16)

Digital In

Digital Out

Digital Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Recording/Playback)

Setting a digital mixer

1. Select the internal clock (INTERNAL).

2. Set the mixer so that it will be able to accept a digital input signal.

* Refer to the instruction manual that came with the external digital device.

Setting the D-160

1. Select a Program.

* Refer to “2-2. Program Change” for the procedure and details.

2. Set a sampling rate.

Set the sampling rate of the D-160 to that of the digital mixer.

* Refer to “2-4. Setting a sampling rate” for the procedure and details.

3. Set the digital input track in Setup mode according to the type of the digital input signal.

* Refer to “2-15. Digital input track setting in Setup mode” on page "157" for

the procedure and details.

4. Set the digital output signal in the digital output track parameter in Setup mode.

* Refer to “2-16. Digital output track setting in Setup mode” on page "159" for

the procedure and details.

<Note>

When you set up a digital input track, the settings for the external sync signal of

the “Slave mode type setting” in Setup mode (that is, Vari, S/P DIF, adat, and Free)

will be ignored, and the D-160 will sync to the specified digital input signal. Refer

to “2-13. Slave mode type setting” in Setup mode on page "155" for more

information.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

Locate Function

The D-160 can immediately locate to any desired point .

That is, it can move the current time or function position of the recorder.

Available locate points are: memory data points (time or bar/beat/clock) stored in

the Memory keys (CLIPBOARD IN/OUT, AUTO PUNCH IN/OUT, AUTO RTN START/

END, and LOCATE keys), the beginning of a Program (ABS 0), and the end of a

recording (ABS END).

The D-160 is also equipped with an Auto function, which operates as an extended

Locate function, including Auto Play, Auto Return, and Auto Repeat functions.

1. Storing memory data

There are three methods by which you can store memory data: by grabbing a

desired time value in real-time when the recorder is playing back or stopped, by

editing and storing a desired data, by recalling previously-stored memory data,

changing it, and storing it.

These methods can also be used in the Auto Return function, Auto Punch In/Out

function, and the edit operations, such as Copy & Paste, Move & Paste, and Erase.

Try to become familiar with the methods described here.

Storing memory data in real-time

1. While the recorder is playing back (or stopped), press the HOLD/> key at the time value

(bar/beat/clock) you wish to store.

The time value of the point at which you pressed the HOLD/> key will be retained,

and the D-160 enter the edit mode. “LOCATE” will light on the display.

2. Press the STORE key. The STORE LED will light.)

3. Press the memory key to which you wish to store data.

The retained time value (bar/beat/clock) will be stored as memory key data,

and the Time Base display will be restored. The STORE LED goes off.

* To take a short cut (to skip Step 2), press the STORE key instead of the HOLD/> key

in Step 1.

Editing and storing data

1. While the recorder is playing back (or stopped), press the HOLD/> key at the time value

(bar/beat/clock) you wish to store.

The time value of the point at which you pressed the HOLD/> key will be retained,

and the D-160 enter the edit mode. “LOCATE” will light on the display.

2. Use the HOLD/> key or the SHUTTLE dial to move among the digits of the time (bar/

beat/clock), and use the JOG dial to edit them.

3. Press the STORE key. The STORE LED will light.

4. Press a memory key to which you wish to store data.

The retained time value (bar/beat/clock) will be stored as memory key data,

and the Time Base display will be restored. The STORE LED goes off.

* To take a short cut (to skip Step 3), press the STORE key instead of the HOLD/> key

in Step 1.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

Recalling, editing, and storing data

1. Press a memory key for which you wish to recall data. (Alternatively, press the RECALL

key, and then a memory key.)

The D-160 will display the time value stored in the key (bar/beat/clock) and enter

the data edit mode.

2. Use the HOLD/> key or the SHUTTLE dial to move among the digits of the time (bar/

beat/clock), and use the JOG dial to edit them.

3. Press the STORE key. The STORE LED will light.

4. Press a memory key to which you wish to store data.

The retained time value (bar/beat/clock) is stored as memory key data, and the Time

Base display will be restored. The STORE LED goes off.

You do not necessarily have to store the edited data to the memory key that you

pressed to recall the original data. For example, you can press the AUTO PUNCH IN

key to recall its memory data, edit it, and store the data to the AUTO PUNCH OUT key.

* Memory data can be stored for each Program (P1-P99) individually.

* Memory data will be saved and loaded as part of the song data in Setup mode.

* Memory data will be retained after you turn off the power.

* Refer to page "50" for information on the Program Change function.

* Refer to page "102" for information on the save and load operation.

<Hints>

If " Resolution?" menu (bar/beat resolution mode) has been turned on in the Setup mode

when the "BAR/BEAT/CLK" Time Based is being used, press the HOLD/> key or the STORE

key to hold the current bar/beat clock value on the display. You can round off the clock

value to "00" (that is, to a bar/beat value).

This function is very useful when you wish to use the memory data in beat steps.

Refer to page "160" for more information on Bar/Beat Resolution ON/OFF menu in Setup

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

2. Locate

The following table shows how to locate to a data point.

Use the following key sequences to locate a certain point.

In this table, "+" indicates that you need to press the specified key while pressing

and holding down the STOP button.

"->" indicates that you need to first press one key, then press a second key.

STOP+REWIND

Locates the beginning of the hard program (ABS 0).

Locates the end of the recorded area on the program (ABS END).

Locates the stored Clipboard In point.

STOP+F FWD

CLIPBOARD IN->LOCATE

CLIPBOARD OUT->LOCATE Locates the stored Clipboard Out point.

AUTO RTN START->LOCATE Locates the stored Auto Return Start point.

AUTO RTN END->LOCATE

Locates the stored Auto Return End point.

AUTO PUNCH IN->LOCATE Locates the stored Auto Punch In point.

AUTO PUNCH OUT->LOCATE Locates the stored Auto Punch Out point.

LOCATE

Locates the stored Locate point (see the note below).

Also, follow the procedure below to locate directly to the point of a time value

(bar/beat/clock).

1. While the recorder is playing back, press the HOLD/> key at the time value (bar/

beat/clock) you wish to store.

The time value of the point at which you pressed the HOLD/> key is retained,

and the D-160 enter the edit mode. "LOCATE" will light on the display.

2. Use the HOLD/> key or the SHUTTLE dial to move among the digits of the time

(bar/beat/clock), and use the JOG dial to adjust their value.

3. Press the LOCATE key.

The D-160 will locate the point of the edited time value, and the Time Base

indication will be restored. ("LOCATE" lights up on the display.)

<Notes>

* Each time a different Memory location (3-8) is located, the LOCATE key memory will

be automatically overwritten by the new time value (bar/beat/clock) of the point that

was just located. For example, assume that the LOCATE key has a Memory location of

00h: 05m: 40s: 00f: 00sf. When you locate an AUTO RTN START point of 00h: 03m:

00s: 00f: 00sf. If you do not perform a different locate operation, the LOCATE key

memory will not change and will always allow the unit to locate to the same point (bar/

beat/clock).

* You can check the LOCATE key memory data by pressing the RECALL key, and then

the LOCATE key. You can also edit this data, and store the LOCATE key's own data by

pressing the STORE key, and then the LOCATE key.

LOCATE point

LOCATE

STOP point

You can set the preroll point within a

range of 0 to 10 seconds (Refer to page

"149" for details.)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

3. Auto Play mode

Turn the Auto Play mode on before using the Direct Locate function, and the D-160 will

automatically start playback from the located point .

The diagram below illustrates this operation.

To turn Auto Play mode on, press the AUTO PLAY/AUTO RTN key so that the AUTO PLAY

LED will light up. To cancel this mode, press the AUTO PLAY/AUTO RTN key again so that

the AUTO PLAY LED will go off.

* Refer to page "15" "Names and Functions" for instructions on using the AUTO PLAY

and AUTO RTN keys.

AUTO PUNCH IN point

LOCATE

PLAY BACK

LOCATE

AUTO PUNCH IN key -> LOCATE key

LOCATE point

You can set the preroll point within a range

of 0 to 10 seconds (Refer to page "149"

for details.)

4. Auto Return mode

To turn Auto Return mode on, press the AUTO PLAY/AUTO RTN key so that the

AUTO RTN LED will light up.

To use the Auto Return function, first you need to specify the Auto Return Start

point and Auto Return End point.

As shown in the diagram below, the D-160 will play back data to the Auto Return

End point, then automatically locate the Auto Return Start point, and then stop.

<Note>

The start point will not be located after the AUTO RTN END point is reached when

the D-160 is in record mode.

AUTO RTN START point

AUTO RTN END point

PLAY BACK

LOCATE

STOP point

You can set the preroll point within a range

of 0 to 10 seconds (Refer to page "149"

for details.)

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

4-1. Setting the Auto Return Start/End point

There are two ways to set the Auto Return Start point and End point: one is to hold

and store a desired time value in real-time during playback or while the D-160 is

stopped; the other is to edit and store the desired time.

Storing the Start/End point in real-time

1, 4

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

2, 5

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

1. While the D-160 is playing back or stopped, press the HOLD/> key at the location

you wish to store as the Start point.

The time value obtained when you press the HOLD/> key will be held, and the

D-160 will enter the edit mode.

* The Bar/Beat Resolution menu setting is available when BAR/BEAT/CLK is used

for the Time Base. Refer to page “160” for details.

2. Press the STORE key. (The STORE LED will light up.)

3. Press the AUTO RTN START key.

The time value you held will be stored as the Start point, and the display will go

back to the previous screen that was before the time value was held. The STORE

LED will go off.

4. Press the HOLD/> key again at the location you wish to store as the End point.

5. Press the STORE key. (The STORE LED will light up.)

6. Press the AUTO RTN END key.

The time value you held will be stored as the End point, and the display will go

back to the previous screen before the time value was held.

* In steps 1 and 4 described above, you can press the STORE key instead of the

HOLD/> key, and then press the AUTO RTN START/AUTO RTN END key to set

the data more quickly.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

Editing and storing the Start/End point

1, 2, 5

3, 7

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

2, 6

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

1. Press the HOLD/> key while the D-160 is playing back or stopped.

The time value at the moment when you pressed the HOLD/> key will be held

and the unit will enter the edit mode.

* The Bar/Beat Resolution menu setting is available when BAR/BEAT/CLK is used

for the Time Base. Refer to page “160” for details.

2. Move the cursor to the time value (bar) using the HOLD/> key or SHUTTLE

dial, and use the JOG dial to change the value.

3. Press the STORE key. (The STORE LED will light up.)

4. Press the AUTO RTN START key.

The edited time value will be stored as the Start point, and the display will

return to the screen displayed before you held the time value. (The STORE LED

will go off.)

5. Press the HOLD/> key again.

6. Enter the value as you did in step 2.

7. Press the STORE key. (The STORE LED will light up.)

8. Press the AUTO RTN END key.

The edited time value will be stored as the End point, and the display will go

back to the screen before you held the time value.

* In steps 1 and 5 described above, you can press the STORE key instead of the

HOLD/> key, edit the time value (bar), and then press the AUTO RTN START/

AUTO RTN END key to set the data more quickly.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

Changing the stored Start / End points

1, 3

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

OUT

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

1. Press the RECALL key, and then the AUTO RTN START key or AUTO RUN END

key. (As a short-cut, you can press the AUTO RTN START key or AUTO RTN

END key directly.)

The display will show the time value stored at the key, and the unit will enter

the edit mode.

2. Move the cursor to the time value (bar) using the HOLD/> key or SHUTTLE dial,

and use the JOG dial to change the value.

3. Press the STORE key, then press the AUTO RTN START key or AUTO RTN END

key.

The edited time value will be stored as the Start point or End point.

<Note>

Pay attention to the location of the Start and End points. If you have set a larger

value to the Start point than the End point while both Auto Return mode and Auto

Play mode are on, the D-160 will jump to the Start point and continue to play the

rest of the data after playing to the End point (which is located before the Start

point).

Therefore, the repeat operation (explained later) will not be carried out correctly).

The Auto Return mode is effective only when the unit is in play mode.

<Hints>

If " Resolution?" menu (bar/beat resolution mode) has been turned on in the Setup

mode when the "BAR/BEAT/CLK" Time Based is being used, press the HOLD/> key or

the STORE key to hold the current bar/beat clock value on the display, and you can

round off the clock value to "00" (that is, to a bar/beat value).

This function is useful when you wish to use the memory data in beat steps.

Refer to page "160" for more information on Resolution menu in Setup mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Locate function)

5. Auto Repeat mode

The Auto Repeat function is a combination of the Auto Play mode and

the Auto Return mode. To access the Auto Repeat function, press the

AUTO PLAY/AUTO RTN key so that both AUTO RTN LED and AUTO PLAY

LED light.

You also need to set the Auto Return Start point and the Auto Return End

point, as you did for the Auto Return function. (Refer to the previous section

"Auto Return" for information on setting the Start and End points.)

With the Auto Repeat function, the D-160 plays data up to the Auto Return

End point, then automatically locates the Auto Return Start point, and

plays back data between the Start and End points repeatedly, until you

cancel playback using the STOP button.

* Refer to page “15” of "Names and Functions" for instructions on using the AUTO

PLAY and AUTO RTN keys.

AUTO RTN START point

AUTO RTN END point

PLAY BACK

LOCATE

LOCATE point

You can set the preroll point within a

range of 0 to 10 seconds (Refer to page

"149" for details.)

<Hints>

Using the Auto Repeat function when you are rehearsing Auto Punch In/

Out recording, allows you to rehearse as many times as you want without

tedious operations. For example, by setting the Start point just before the

Auto Punch In point and the End point just before the Auto Punch Out

point, you do not need to worry about locating the data and can concentrate

on rehearsing.

AUTO PUNCH OUT point

AUTO PUNCH IN point

AUTO RTN START point

AUTO RTN END point

Rehearsal area

PLAY BACK

Rehearsal will be repeated automatically as many times

as you like to make it easier to adjust the recording level.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

Punch In/Out

Punch In/Out recording is used to re-record data onto a certain area of a pre-

recorded track. For example, you can replace a phrase from your guitar solo

with a better performance.

There are two ways to Punch In/Out record: Auto Punch In/Out recording, in

which you specify the Punch In/Out points; and Manual Punch In/Out recording,

in which you use optional foot switch Model 8051.

In either case, the Rehearsal function allows you to practice before the actual

take. Using the Punch In/Out recording technique, you can easily and quickly

replace mistakes or phrases you do not like with more desirable takes.

Choose one of these methods to suit your preferences and applications.

* The example here explains how to replace "part of the guitar solo" recorded on

Track 3 with a new phrase by playing the guitar , while listening to the drum and

bass sound recorded on Tracks 1 and 2.

Once you master Punch In/Out recording, you can use this technique for other

tracks.

* Assume that the guitar is connected to the mixer input, and that the output signal

from the mixer is routed to Track 3 of the D-160.

* Do not change the Program or sampling rate until the session is complete.

* First make sure that the D-160 is set to the default setting.

Punch Out point

Punch In point

Track 16

Track 15

Track 14

Track 13

Track 12

Track 11

Track 10

Track 9

Track 8

Track 7

Track 6

Track 5

Track 4

Track 3

Track 2

Track 1

Replace area

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

1. Auto Punch In/Out

To perform Auto Punch In/Out recording, first you need to specify the In

point (recording start point) and the Out point (recording end point).

Once these two points are stored, the D-160 automatically starts recording

at the In point and stops recording at the Out point while the recorder is in

"Take mode." When you use the Auto Punch In/Out function, you can

select "Rehearsal mode" to practice to your satisfaction before you record.

1-1. Storing the Punch In/Punch Out point

Here, we assume that Program 1 with the “ABS” Time Base has been selected.

If you wish to choose other Program, press the STORE key while holding

down the HOLD/> key.

Storing the Punch In point

1, 2

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

OUT

END

DISP SEL

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

HOLD/

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

1. Press the HOLD/> key while the recorder is playing back or stopped.

The following example shows that a time of two minutes, 40 seconds, 3 frames,

and 28 sub-frames is held, and the Program indication is changed to the sub-

frame indication.

Blink (Edit point)

* Pressing the STORE key will enter the D-160 to into hold/edit status.

In this case, you can omit step 3 below.

2. Press the HOLD/> key or turn the SHUTTLE dial to select the digit you wish to

edit, and then use the JOG dial to change the time value.

For example, setup the Auto Punch In point to "3 minutes, 15 seconds, 10 frames".

3. Press the STORE key. (The STORE LED will light up.)

4. Press the AUTO PUNCH IN key.

The specified time value will be stored as a Punch In point, and the STORE LED

will go off.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

Storing the Punch Out point

5, 6

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

HOLD/

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

5. Press the HOLD/> key to enter edit mode.

6. Press the HOLD/> key or turn the SHUTTLE dial to select the digit you wish to

edit, then use the JOG dial to change the time value.

For example, setup the Auto Punch Out point to "3 minutes, 35 seconds, 15

frames".

7. Press the STORE key. (The STORE LED will light up.)

8. Press the AUTO PUNCH OUT key.

The specified time value will be stored as a Punch Out point, and the STORE LED

will go off.

* To check the stored Punch In/Out point, press the RECALL key, and then press

the AUTO PUNCH IN key and/or the AUTO PUNCH OUT key.

Alternatively, press the AUTO PUNCH IN/AUTO PUNCH OUT key.

The display will show the stored time value.

<Note>

You cannot set the Punch Out point before the Punch In point location.

If the Punch Out point precedes the Punch In point and you try to "punch in,"

the message "Void Out Point!" appears on the screen immediately after you press

the AUTO PUNCH key, indicating that the time value of the Punch Out point is

inappropriate. Be sure to specify a larger value for the Punch Out point than for

the Punch In point.

<Hints>

If “ Resolution” menu (Bar/Beat Resolution mode) has been turned on in the

Setup mode when the “BAR/BEAT/CLK” Time Based is being used, press the

HOLD/> key or the STORE key to hold the current bar/beat clock value on the

display, and you can round off the clock value to “00” (that is, to a bar/beat

value). This function is useful when you wish to use the memory data in beat

steps.

* Refer to page "*160" for more information on " Resolution" menu in Setup

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

1-2. Auto Punch In/Out Rehearsal mode

Set the “READY” track into Input monitoring status for the part between

the Punch In point and the Punch Out point in Rehearsal mode. (Other

tracks are in playback monitoring status.) In Rehearsal mode, nothing is

actually recorded. You can repeat rehearsal as many times as you wish

adjust the In point, Out point, and recording level.

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

OUT

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

Rehearsal

1. Press the RECORD TRACK select “3” key to ready Track 3. (“3” on the display

will blink.)

2. Locate a point just before the Punch In point, using one of the following methods:

Press the AUTO PUNCH IN key, then the LOCATE key. (The Auto Punch In point

will be located.) Then, press the REWIND button, or turn the SHUTTLE dial

counter-clockwise to locate a position slightly ahead. Setting a “Pre-roll” value

will make it easier to locate a position the specified number of seconds before

the Auto Punch In point.)

Refer to page "149" for information on the Pre-roll setting function.

Alternatively, you can store the playback start point (time) at the AUTO RTN

START for future locate operations. (You need to use the AUTO RTN START

key for Step 4 of "Storing the Punch In point.")

3. Press the AUTO PUNCH key. (The REHEARSAL and TAKE LEDs will light up.)

If the disk does not have enough free space for auto punch in/out, the “Over !”

indications appear.

Refer to “Warning” in the “Display” section in the manual.

4. Press the PLAY button.

Rehearsal mode is engaged as follows on the next page:

5. Rehearse the guitar part while playing back the drum and bass sounds.

You will hear the guitar sound you are playing only between the punch in and

punch out points.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

Rehearsal mode (Auto Punch In/Out)

AUTO PUNCH OUT point

AUTO PUNCH IN point

All tracks are under REPRO

Only track 3 enters INPUT monitoring

All tracks are under REPRO

monitoring status.

status. (However, the D-160 will not

record and data in Rehearsal mode.)

RECORD TRACK display

Blink

Light up

REHEARSAL LED

TAKE LED

REHEARSAL LED will light up.

REHEARSAL LED will light up

PLAY

PLAY button LED

PLAY LED will light up

PLAY

PLAY LED will light up

RECORD

RECORD button LED

RECORD LED will blink

<Hints>

If you are rehearsing over and over, an effective time-saver is to use the Auto Return

function along with the Auto Play function.

As shown in the diagram below, specifying the Start and End points for the Auto Return

and Auto Play functions allows you to easily rehearse as many times as you like. This

enables you to pay more attention to the recording level and your own performance.

Refer to pages "71" for more information on setting the Start/End points for the Auto

Return/Auto Play functions.

AUTO PUNCH IN point

AUTO PUNCH OUT point

AUTO RTN START point

AUTO RTN END point

Rehearsal will be repeated automatically as many times as

you like to make it easier to adjust the recording level.

1-3. Auto Punch In/Out Take mode (actual recording)

Proceed to recording after rehearsal.

Take

1. Check to see which tracks are in ready mode.

Please note that data will be recorded in all tracks set to ready mode.

2. As in Rehearsal mode, locate the point just before the Punch In point.

3. Auto Punch mode is "on".

4. Press the RECORD button while pressing and holding down the PLAY button.

The REHEARSAL LED (green) will go off and the TAKE LED (red) will light up.

5. Play the guitar while listening to the playback sound.

As shown in the illustration below, the recorder will start recording automatically

at the Punch In point, and stop recording at the Punch Out point.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

* When recording is finished, the Auto Punch mode will be canceled, and both

REHEARSAL and TAKE LEDs will go off.

Take mode (Auto Punch In/Out)

AUTO PUNCH OUT point

AUTO PUNCH IN point

Only Track 3 enters INPUT monitoring

All tracks are under REPRO

monitoring status.

All tracks are under REPRO

monitoring status.

status. (Unlike in Rehearsal mode, the

D-160 will record data.)

Refer to "Caution after Punch

Out" for details.

Blink

RECORD TRACK display

Light up

REHEARSAL LED

TAKE LED

TAKE LED will light up

Both LEDs will go off

PLAY

PLAY button LED

PLAY LED will light up

PLAY

PLAY LED will light up

RECORD

RECORD button LED

RECORD LED will light up

At "Take" of punch out, the punch-in recording track will not immediately

enter the repro monitor mode from the input monitor mode but enter

the repro monitor mode about two seconds after mute playback.

This is a functional feature of D-160 and not a malfunction.

1-4. Undo/Redo of Auto Punch In/Out

* If you press the UNDO key after performing the auto punch in/out operation, the original sound

recorded prior to auto punch in/out will be restored.

* If you press the REDO key after undoing the auto punch in/out operation, the auto punch in/out

data will be restored.

<Note>

You can use the undo/redo functions while the D-160 is in stop mode.

Under the following circumstances, you will be unable to use the undo/redo functions;

1. If you make a new recording,

2. If you make a new edit (copy & paste, move & paste, or erase),

3. If the Auto Punch In point was passed in play or record mode while Auto Punch

mode was on, or

4. If you turned off the power to the D-160, then turned it back on.

5. If you use the Program Change function.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

2. Punch In/Out Recording using a foot switch

The "Take mode" and "Rehearsal mode" are also available in this application.

Pressing the foot switch repeatedly while holding down the STOP button

will toggle between "take" and "rehearsal." The REHEARSAL LED of the

AUTO PUNCH key will blink during Rehearsal mode, and the LED will turn

off during "Take mode."

1. Select the track onto which you wish to punch in/out record.

2. Start playback just before the punch in point.

3. Press the foot switch when you want to start recording.

4. Press the foot switch again when recording is finished.

In this lesson, we are going to replace part of the guitar solo recorded on

Track 3, as we did in the Auto Punch In/Out section.

Set the D-160 to the default setting.

Use an optional foot switch Model 8051 for punch in/out recording.

Set Auto Punch mode to OFF. (The REHEARSAL LED and the TAKE LED will be

turned off.)

Do not change the Program or sampling rate until the session is complete.

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

OFF (REHEARSAL LED/TAKE

LEDs will go off.)

FOOT SWITCH Model 8051

Turn off the D-160 before connecting or disconnecting any cables.

Connecting or disconnecting the footswitch or detachable controller

cables while the D-160 is turned on will cause it to malfunction.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

2-1. Punch In/Out Rehearsal (Using a foot switch)

Rehearsal

1. Press the foot switch once while holding down the STOP button.

The D-160 will enter the "Rehearsal" mode, and the 35 dot display on the upper

row of the screen will show "Rehearsal On" for one second. Only the REHEARSAL

LED (green) will blink.

2. Press the RECORD TRACK select key “3” to set Track 3 to ready mode. (Indicator

“3” will flash.)

3. Press the PLAY button at a location just before the punch in point to play back

data.

4. Rehearse the guitar part while playing back the drum and bass sounds.

5. Press the foot switch once at the Punch In point, and press the foot switch

again at the Punch Out point. The following diagram illustrates this operation.

You will hear the guitar sound you are playing only between the punch in and

out points.

Rehearsal mode (manual Punch In/Out)

PUNCH OUT point

PUNCH IN point

Only Track 3 enters INPUT monitoring

All tracks are under REPRO

monitoring status.

All tracks are under REPRO

monitoring status.

status. (However, the D-160 will not

record any data in Rehearsal mode.)

Press the foot

switch again.

Press the foot

switch once.

Blink

RECORD TRACK display

Light up

REHEARSAL LED

TAKE LED

REHEARSAL LED will blink

PLAY

PLAY button LED

PLAY LED will light up

PLAY

PLAY LED will light up

RECORD

RECORD button LED

RECORD LED will blink

End of rehearsal

1. Press the foot switch again while holding down the STOP button to cancel

Rehearsal mode.

The 35 dot display on the upper row of the screen will show "Rehearsal Off"

for one second. Also, the REHEARSAL LED (green) will turn off, indicating that

you have quit the Rehearsal mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

<Hints>

When you are rehearsing over and over, an effective time-saver is to use

the Auto Return function along with the Auto Play function.

As shown in the diagram below, specifying the Start and End points for

the Auto Return and Auto Play functions allows you to easily rehearse as

many times as you like. In this way, you can pay more attention to the

recording level and your own performance. Refer to pages "71" for more

information on setting the Start/End points for the Auto Return/Auto Play

functions.

PUNCH IN point

PUNCH OUT point

AUTO RTN START point

AUTO RTN END point

Rehearsal will be repeated automatically as many times as you

to make it easier to adjust the recording level.

2-2. Punch In/Out Take (manual Punch In/Out)

1. Locate the point just before the punch in point and play back the data.

2. Play the guitar while listening to the playback.

3. Press the foot switch once at the punch in point, and press it again at the

punch out point.

When you finish punch out recording, the D-160 will quit recording mode.

Take mode (manual Punch In/Out)

PUNCH IN point

PUNCH OUT point

All tracks are under REPRO

Only Track 3 enters INPUT monitoring

All tracks are under REPRO

monitoring status.

monitoring status. Refer to

"Caution after Punch Out" for

details.

status. (Unlike in Rehearsal mode, the

D-160 will record data.)

Press the foot

switch again.

Press the foot

switch once.

Blink

Light up

RECORD TRACK display

REHEARSAL LED

TAKE LED

Both LEDs will go off

PLAY

PLAY button LED

PLAY LED will light up

PLAY

PLAY LED will light up

RECORD

RECORD button LED

RECORD LED will light up

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Punch In/Out)

At "Take" of punch out, the punch-in recording track will not immediately enter

the repro monitor mode from the input monitor mode but enter the repro monitor

mode about two seconds after mute playback.

This is a functional feature of D-160 and not a malfunction.

<Note>

Once you perform Punch In/Out recording using a footswitch, you need to stop

the D-160 before performing the next Punch In/Out take.

<Hints>

Besides the foot switch, you can also use the PLAY button and RECORD

button for Manual Punch In/Out recording. (Please note that you can

use these buttons only once.)

1. Start playing back from a point just before the punch in point.

2. At the punch in point, press the RECORD button while holding down the

PLAY button. (Punch In)

3. At the punch out point, press only the PLAY button. (Punch Out)

* You can also rehearse if you "press only the RECORD button" instead

of steps 2 and 3 described above.

2-3. Undo/Redo of Manual Punch In/Out

* If you press the UNDO key after performing the manual punch in/out operation, the original

sound recorded prior to auto punch in/out will be restored.

* If you press the REDO key after undoing the manual punch in/out operation, the manual punch

in/out data will be restored.

<Note>

You can use the undo/redo functions while the D-160 is in stop mode.

Under the following circumstances, you will be unable to use the undo/redo functions;

1. If you make a new recording,

2. If you make a new edit (copy & paste, move & paste, or erase),

3. If the Auto Punch In point was passed in play or record mode while Auto Punch

mode was on, or

4. If you turned off the power to the D-160, then turned it back on.

5. If you use the Program Change function.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

Edit Function

This chapter describes the various editing functions on the D-160.

The D-160 uses a hard disk as the recording media, which allows for non-

linear, non-destructive, quick audio editing. The edit function includes

the Copy & Paste, Move & Paste, and Erase functions.

The D-160 accommodates ninety-nine Programs, P1-P99, each of which you can

record and edit individually. First, make sure that you are about to edit the correct

Program. If you start editing without first checking the Program, you may lose

important data. Refer to the Before operation section, “2-2. Program Change,” for

more information on how to set a Program. Do not change Programs or sampling

rates until a session is complete.

* The Copy & Paste function allows you to copy data to the Clipboard, and paste it to

any location in any track. In this case, the copy source data remains as is, as does the

data on the Clipboard.

* The Move & Paste function is almost the same as the Copy & Paste, except that

executing the Move & Paste function will erase the move source data (the Clipboard

will be also cleared).

CLIPBOARD IN point

CLIPBOARD OUT point

Copy & Paste

Source track

COPY

Clipboard

PASTE

Paste track

AUTO PUNCH IN point

CLIPBOARD IN point

CLIPBOARD OUT point

Move & Paste

Source track

MOVE

Clipboard

PASTE

Paste track

AUTO PUNCH IN point

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

1. Copy & Paste

The Copy & Paste functions use the clipboard of the D-160, allowing you

to copy sound data and paste it to the specified area. The copied data

remains on the clipboard after you paste it, and you can paste the same

data as many times as you want to different places. The Copy & Paste

functions can reference any one of the following time bases: ABS time,

MTC time, MIDI Bar/Beat/Clock.

To perform the Copy operation, you first need to set the start point (Clipboard In point) and the

end point (Clipboard Out point) of the copied data and the copy source track.

To perform the Paste operation, you need to set the start point (Auto Punch In point) and the

paste destination point.

<Note-1>

The data on the Clipboard will be replaced by new data each time you press the COPY

key of the MOVE key.

<Note-2>

If pasted data overlaps the source data, the content of the source data will be altered.

1-1. Copying

First, you need to specify the area to be copied (using the Clipboard In/

Out points and copy track).

The following procedure is based on data with the ABS Time Base.

To change the Time Base to MTC or MIDI BAR/BEAT/CLK, press the DISP SEL key while

pressing and holding down the EXECUTE/YES key.

Before you start work, restore the default settings on the D-160.

Do not change Programs or sampling rates until a session is complete.

1, 3

4, 6

3, 6

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

HOLD/

STORE

RECALL

1, 4

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN / OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

2, 5

Entering and storing the CLIPBOARD IN point

1. Press the RECALL key, and then the CLIPBOARD IN key (or press only the

CLIPBOARD IN key). The D-160 will enter the edit mode.

2. Move the cursor to the digit you wish to change using the HOLD/> key or the

SHUTTLE dial, and change the value using the JOG dial.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

3. After setting the value, press the STORE key, then the CLIPBOARD IN key.

The time value will be stored as the Clipboard In time, the edit mode will

disengage, and the display will return to the previous screen.

Entering and storing the CLIPBOARD OUT point

4. Press the RECALL key, and then the CLIPBOARD OUT key (or press only the

CLIPBOARD OUT key). The D-160 will enter the edit mode.

5. Move the cursor to the digit you wish to change using the HOLD/> key or the

SHUTTLE dial, and change the value using the JOG dial.

6. After setting the value, press the STORE key, and then the CLIPBOARD OUT

key.

The time value will be stored as the Clipboard Out time, the edit mode will

disengage, and the display will return to the previous screen.

* To check the stored In/Out points, press the CLIPBOARD IN key and CLIPBOARD

OUT key respectively. The time value you just stored will be shown on the display.

* You can perform steps 1-3 in real-time. (Pressing the STORE key, then the

CLIPBOARD IN key while playing back the recorder will store data.)

<Hints>

When you are storing the In/Out points in real-time while using the “BAR/BEAT/

CLK” Time Base, you can store them in steps of beats if the “ Resolution ?” menu

(Bar/Beat Resolution mode ON/OFF) in Setup mode is “On.”

When this bar/beat resolution menu is “On,” the CLK value will be rounded to

“00” (at the beginning of the beat) as soon as you press the STORE key.

This function is useful when you wish to use the Copy & Paste or Move & Paste

function in setups of beats. Refer to page “160” for detailed operation.

Copying the track data after storing the CLIPBOARD IN/OUT points

7. Select the copy track using the RECORD TRACK select keys (you can select

multiple tracks).

* You can select one (mono) track, multiple tracks, or all sixteen tracks.

When using the Copy & Paste function, however, you can change the paste

destination track only when you have selected a mono track, or an odd-numbered

track and the adjacent even-track (i.e.: 1-2, 3-4, or 13-14,15-16).

If you have copied multiple tracks (other than the above combination), the data will

be pasted to the copy source tracks. (track 1-> track 1.........track 3-> track 3 etc.)

8. Press the COPY key.

Upon finishing copying to the clipboard, "Copy Clip"/"COMPLETED!" will appear

in the display and then return to the original time base display.

In this way, the specified part of the sound data of the selected track(s) is

copied to the clipboard.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

If you press the COPY key without selecting a copy source track by the RECORD

TRACK select key, the display will show "Select Track!" (meaning “Select a copy track.”)

and return to the previous screen. In this case, select a copy source track and try to

copy the data again.

If an Output point has been specified before the In point (the In point value is the

same or large than the Out point value), the display will show the error message

“Void In Point!” or “Void Out Point!” and return to the previous screen. In this case,

set the correct In/Out points and try again to copy the data.

The data on the Clipboard will be replaced by new data each time you press the COPY

key or the MOVE key.

Listening to sound data copied on the clipboard (Clipboard Play function)

To listen to the sound data currently copied to the clipboard, press the

PLAY button while holding down the STOP button (Clipboard Play mode).

The data will be played back from the beginning. To stop the playback in

the middle, press the STOP button.

During the clipboard playback, the display show the position of the source data

referenced to the selected time base.

1-2. Copy & Pasting

You can paste data to the same track as the source. For example, if you

copied data on Track 1, data will be pasted on Track 1. Data will be pasted

starting from the Auto Punch In point.

<Note>

You need enough unrecorded space on the hard disk to execute the Copy & Paste operation.

If you press the PASTE key with insufficient disk space, the display will immediately show

the error message “Over !”, and then show the excess time using the currently-selected Time

Base (time or bar).

In this case, shorten the copy data by the amount of excess time. Alternatively, move ABS

END backward using the ERASE function as described in page “96” of this manual in order

to obtain more free space on the hard disk.

1, 3

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

OUT

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

Entering and storing the paste Punch In point

1. Press the RECALL key, then the AUTO PUNCH IN key (or press only the AUTO

PUNCH IN key). The D-160 will enter the edit mode.

2. Move the cursor to the digit you wish to edit using the HOLD/> key or the

SHUTTLE dial, and set the value using the JOG dial.

3. After setting the time value, press the STORE key, and then the AUTO PUNCH

IN key.

The time value will be stored as the start point of the pasting area, and the

display will go back to the previous screen.

Executing the paste operation

4. Press the PASTE key.

When the PASTE key is pressed, "Copy Paste" is momentarily show in the display,

then "Paste Repeat = 01 (01 blinks)" and "SURE?" will blink, and the copy source

track display will be lit.

5. Specifying the copy destination track and the number of repeats to paste.

* Specifying the Copy & Paste destination track:

Select the destination track using the RECORD TRACK select key. (You do not

need to specify the track if you are going to Copy & Paste data in the copy

source track.)

* Specifying the number of repeats to Copy & Paste:

Turn the JOG dial to change the blinking number “01” to any value between 1

and 99. (If there is not enough free space on the hard disk, the repeat time will

be limited to a number less than 99, and you will be unable to specify a larger

number when you turn the JOG dial.)

6. Press the EXECUTE/YES key.

Simultaneous with execution of paste, the paste section length converted to

mono track time length will be shown in the upper line of the display and "Copy

Paste," "COMPLETED!" displayed after completing the paste.

Press the EXIT/NO key to go back to the previous screen.

Now the audio data on the Clipboard has been pasted to the specified

track starting with the AUTO PUNCH IN point.

For example, executing the function with a repeat number of “Paste Repeat=

03” (three times) will paste the data as shown in the diagram below.

AUTO PUNCH IN point

Repeat number of "01"

Repeat number of "03"

* To cancel the paste operation, press the EXIT/NO key while the message “SURE?” is

blinking on the display.

If you wish to cancel the paste operation after you press the EXECUTE/YES key, press

the STOP button or the EXIT/NO key before the “COMPLETED!” message appears on

the display.

If you abort the paste operation using this procedure (even in the middle of the operation),

no data will be pasted.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

The Copy & Paste function is available only when the hard disk has enough space

(REMAIN) to perform the following Undo/Redo operation.

If you try to copy & paste the data without enough free space on the hard disk, the

display will indicate the alarm message “Over !” (overtime error) as soon as you

press the PASTE key, then indicate the excessive time in the currently-selected

Time Base.

To avoid this, shorten the data to be copied, by the amount of the exceeding time,

or use the Erase function to create free disk space as described below in order to

move the ABS END point.

Do not copy data and paste it partially over itself (same track and part of the same

time frame). This will alter both the copy source data and the data currently

contained in the clipboard.

If you accidentally do this, use the Undo function as explained in the following

section. You will be unable to restore the original data if you proceed with editing

without first performing the Undo operation.

You can also paste the move data repeatedly by specifying the number of repeats

(1-99). The difference between "Move & Paste" and "Copy & Paste" is that moving

data will cause the source sound data to move to the Clipboard, and then to the

destination, and the data in the source or in the Clipboard will be erased.

This operation is available with any Time Base.

1-3. Copy & Paste Undo/Redo

If you wish to restore data that existed before you executed the Copy & Paste

function, press the UNDO key to restore the status obtained before you pasted the

data. Pressing the REDO key after pressing the UNDO key will restore the status

before the Undo operation (that is, after pasting). The Undo and Redo functions

are effective only when the D-160 is stopped.

After the UNDO key or REDO key is pressed, the display will show "Undo" or "Redo",

and "COMPLETED!" and return to the previous screen.

<Note>

You can use the undo/redo functions while the D-160 is in the stop mode.

Under the following circumstances, you will be unable to use the undo/redo functions:

1.If you make a new recording,

2.If you make a new edit (Copy & Paste, Move & Paste, Erase),

3.If the Auto Punch In point was passed in play or record mode while Auto Punch mode

was on, or

4. If you turned off the power to the D-160, then turned it back on.

5. If you use the Program Change function.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

2. Move & Paste

The Move & Paste function “moves” sound data to the Clipboard, and

“pastes” the data in the same track or another track. You can specify the

number of repeats of the paste operation (1-99) to paste data repeatedly.

The difference between the Copy & Paste and the Move & Paste operation

is that, after the Move & Paste operation, the source data and the data on

the Clipboard will be removed. You can use this function with any Time

Base.

* To perform the Move operation, you first need to set the start point (Clipboard In point)

and the end point (Clipboard Out point) of the data to be moved, and the move source

track. To perform the Paste operation, you need to set the start point (Auto Punch In

point) and the paste destination point.

<Note>

The data on the Clipboard will be replaced by new data each time you press the

COPY key or the MOVE key.

2-1. Moving

First, you need to specify the area to be moved (using the Clipboard In/

Out points and move track).

The following procedure is based on data with the ABS Time Base.

To change the Time Base to MTC or MIDI BAR/BEAT/CLK, press the DISP SEL key while

pressing and holding down the EXECUTE/YES key.

Before you start working, restore the default settings on the D-160.

Do not change Programs or sampling rates until a session is complete.

1, 3

4, 6

3, 6

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

HOLD/

STORE

RECALL

1, 4

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN / OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

2, 5

Entering and storing the CLIPBOARD IN point

1. Press the RECALL key, and then the CLIPBOARD IN key (or press only the

CLIPBOARD IN key). The D-160 will enter the edit mode.

2. Move the cursor to the digit you wish to change using the HOLD/> key or the

SHUTTLE dial, and change the value using the JOG dial.

3. After setting the value, press the STORE key, and then the CLIPBOARD IN key.

The time value will be stored as the Clipboard In time, the edit mode will

disengage, and the display will return to the previous screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

Entering and storing the CLIPBOARD OUT point

4. Press the RECALL key, and then the CLIPBOARD OUT key (or press only the

CLIPBOARD OUT key). The D-160 will enter the edit mode.

5. Move the cursor to the digit you wish to change the HOLD/> key or the SHUTTLE

dial, and change the value using the JOG dial.

6. After setting the value, press the STORE key, and then the CLIPBOARD OUT

key.

The time value will be stored as the Clipboard Out time, the edit mode will

disengage, and the display will return to the previous screen.

* To check the stored In/Out points, press the CLIPBOARD IN key and CLIPBOARD

OUT key respectively. The time value you just stored will be shown on the

display.

* You can perform steps 1-3 in real-time. (Pressing the STORE key, then the

CLIPBOARD IN key while playing back the recorder will store data.)

<Hints>

When you are storing the In/Out points in real-time while using the “BAR/BEAT/

CLK” Time Base, you can store them in steps of beats if the “ Resolution ?" menu

(Bar/Beat Resolution mode ON/OFF) in the Setup mode is “On.”

When this bar/beat resolution mode is “On,” the CLK value will be rounded up

or off to “00” (at the beginning of the beat) as soon as you press the STORE key.

This function is useful when you wish to use the Copy & Paste or Move & Paste

function is steps of beats. Refer to page “160” for detailed operation.

Moving the track data after storing the CLIPBOARD IN/OUT points

7. Select the move track using the RECORD TRACK select keys (you can select

multiple tracks).

* You can select one (mono) track, multiple tracks, or all sixteen tracks.

When using the Copy & Paste or Move & Paste function, however, you can change

the paste destination track only when you have selected a mono track, or an odd-

numbered track and the adjacent even-numbered track (i.e.: 1-2, 3-4, or 13-14, 15-

16). If you have moved multiple tracks (other than the above combination), the data

will be pasted to the move source tracks. (track 1-> track 1..........track 3-> track 3 etc.)

8. Press the MOVE key.

Upon finishing moving in the clipboard, "Move Clip"/"COMPLETED!" will appear

in the display and then return to the original time base display.

Now the sound data in the specified track has been moved to the Clipboard.

At this point, the move source data has yet been deleted. It will be deleted

after you perform the paste operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

If you press the MOVE key without selecting a move source track by the RECORD

TRACK select key, the display will show "Select Track!" (meaning “Select a move

track.”) and return to the previous screen. In this case, select a move source track

and try again to copy the data.

If the Output point has been specified before the In point (the In point value is the

same or large than the Out point value), the display will show the error message

“Void In Point !” or “Void Out Point !” and return to the previous screen. In this case,

set the correct In/Out points and try again to move the data.

The data on the Clipboard will be replaced by new data each time you press the

COPY key or the MOVE key.

Listening to sound data moved on the clipboard (Clipboard Play function)

To listen to the sound data currently moved to the clipboard, press the

PLAY button while holding down the STOP button (Clipboard Play mode).

The data will be played back from the beginning. To stop the playback in

the middle, press the STOP button.

* During the clipboard playback, the display shows the position of the source data

referenced to the selected time base.

2-2. Move & Pasting

The data will be move & pasted at the point stored in the Auto Punch In

key. You can select the paste destination track the RECORD TRACK select

key.

<Note>

You need to have enough unrecorded space on the hard disk to execute the Move

& Paste operation. If you press the EXECUTE/YES key to try to paste data with

insufficient disk space, the display will immediately show the error message “Over

!,” and then show the excess time using the currently-selected Time Base (time or

bar).

In this case, shorten the move data by the amount of excess time. Alternatively,

move ABS END backward using the Erase function as described in page “96” of this

manual in order to obtain more free space on the hard disk.

1, 3

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

OUT

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

Entering and storing the paste Punch In point

1. Press the RECALL key, and then the AUTO PUNCH IN key (or press only the

AUTO PUNCH IN key). The D-160 will enter the edit mode.

2. Move the cursor to the digit you wish to edit using the HOLD/> key or the

SHUTTLE dial, and set the value using the JOG dial.

3. After setting the time value, press the STORE key, and then the AUTO PUNCH

IN key.

The time value will be stored as the start point of the pasting area, and the

display will return to the previous screen.

Executing the paste operation

4. Press the PASTE key.

When the PASTE key is pressed, "Move Paste" is momentarily shown in the display,

then "Paste Repeat = 01 (01 blinks)" and "SURE?" will blink, and the move source track

display will be lit.

5. Specify the Move & Paste destination track and the number of repeats to paste.

* Specifying the Move & Paste destination track:

Select the destination track using the RECORD TRACK select key.

You do not need to specify a track if you are going to Move & Paste data in the

copy source track.

* Specifying the number of repeats to Move & Paste:

Turn the JOG dial to change the blinking number “01” to any value between 1

and 99. If there is not enough free space on the hard disk, the repeat time will

be limited to a number less than 99, and you will be unable to specify a larger

number when you turn the JOG dial.

6. Press the EXECUTE/YES key.

Simultaneous with the execution of paste, the paste section length converted to

mono track time length will be shown in the upper line of the display and

"Move Paste," "COMPLETED!" displayed after completing the paste.

Press the EXIT/NO key to return to the previous screen.

Now the audio data on the Clipboard has been pasted to the specified

track starting with the AUTO PUNCH IN point.

For example, executing the function with a repeat number of “Paste Repeat=

03” (three times) will paste the data as shown in the diagram below.

AUTO PUNCH IN point

Repeat number of "01"

Repeat number of "03"

* To cancel the paste operation, press the EXIT/NO key while the message “SURE?” is

blinking on the display.

If you wish to cancel the paste operation after you press the EXECUTE/YES key,

press the STOP button or the EXIT/NO key before the “COMPLETED!” message

appears on the display.

If you abort the paste operation using this procedure (even in the middle of the

operation), no data will be pasted.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

The data on the Clipboard will be cleared after the Move & Paste operation is complete.

Unlike the Copy & Paste operation, you cannot repeatedly move and paste the same

data.

The Move & Paste function is available only when the hard disk has enough space

(REMAIN) to perform the following Undo/Redo operation.

If you try to move & paste the data without enough free space on the hard disk, the

display will indicate the alarm message “Over !” (overtime error) as soon as you

press the PASTE key, then indicate the excessive time in the currently-selected Time

Base. To avoid this, shorten the data to be copied, by the amount of the exceeding

time, or use the Erase function to create free disk space as described later in order

to move the ABS END point.

Do not copy data and paste it partially over itself (same track and part of the same

time frame). This will alter both the copy source data and the data currently

contained in the clipboard.

If you accidentally do this, use the Undo function as explained in the following

section. You will be unable to restore the original data if you continue to edit

without first performing the Undo operation.

You can also paste the move data repeatedly by specifying the number of repeats

(1-99). The difference between "Move & Paste" and "Copy & Paste" is that moving

data will cause the source sound data to move to the Clipboard, then to the

destination, and the data in the source or in the Clipboard will be erased.

This operation is available with any Time Base.

2-3. Move & Paste Undo/Redo

If you wish to restore data that existed before you executed the Move & Paste

function, press the UNDO key to restore the status obtained before you pasted the

data. Pressing the REDO key after pressing the UNDO key will restore the status

before the Undo operation (that is, after pasting). The Undo and Redo functions

are effective only while the D-160 is stopped.

After the UNDO key or REDO key is pressed, the display will show "Undo", "Redo"

and "COMPLETED!" and return to the previous screen.

<Note>

You can use the undo/redo functions while the D-160 is in stop mode.

Under the following circumstances, you will be unable to use the undo/redo

functions:

1.If you make a new recording,

2.If you make a new edit (Copy & Paste, Move & Paste, or Erase,

3.If the Auto Punch In point was passed in play or record mode while Auto

Punch mode was on, or

4. If you turned off the power to the D-160, then turned it back on.

5. If you use the Program Change function.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

3. Erase

There are three ways to erase data. Make sure that you learn the difference ways to erase

to avoid mistakes.

Erasing data for a specific part between ABS 0 and ABS END:

You can erase data (make silence) from the Auto Punch In point up to the Auto Punch Out

point between ABS 0 - ABS END. You may specify a mono track, multiple tracks, or all 16 tracks

for the erase operation. As shown in the diagram below, this operation erases data for any

specified part between ABS 0 and ABS END. But, the ABS END position will not be affected.

The REMAIN value (available recording time based on a single mono track) will increase by

the amount you erase.

AUTO PUNCH OUT point

AUTO PUNCH IN point

ABS END

ABS 0

Any Track

Erase

No sound area

Erasing all data from a specified point up to ABS END:

You may erase data from a specified point (Auto Punch In point) up to ABS END of a selected

Program. You need to specify the erase start point as the Auto Punch In point, and the ABS

END point (the end point of recording) or any point (time) after the ABS END point as the Auto

Punch Out point. You may specify a mono track, multiple tracks, or all 16 tracks for the erase

operation. If you specify all tracks, the ABS END point of the selected Program will move back

and the REMAIN value will increase. If you specify any other track combination, the ABS END

point will not move; only the REMAIN value will increase.

AUTO PUNCH OUT point

ABS END

AUTO PUNCH IN point

ABS 0

Any Track

Erase

Non recorded area

ABS END

Erasing specific Program data (Program Erase):

This function enables you to erase data entirety from a selected program and return the

initial settings of this program to its initial figures.

Unlike the other two erase functions, for Program Erase you do not need to specify tracks or

set the Auto Punch In/Out points. Executing this erase function will erase all data recorded in

the selected Program. The ABS time and the REMAIN value will return to their default settings.

Use caution, since you cannot UNDO this erase operation.

ABS 0

ABS END

All data recorded in

a random program.

Recorded area

Program Erase

ABS 0 = ABS END

Any Program

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

3-1. How to Erase data for a specific part between ABS 0 and ABS END

Storing the erase start point (Auto Punch In point) and the erase end point (Auto Punch Out point)

Refer to “1. Storing memory data,” to set the Auto Punch In/Out points.

Here, we use the procedure to “edit the stored data.”

5, 8

3, 7

1, 4

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

1, 5

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

2, 6

1. Press the AUTO PUNCH IN key. (Or, press the RECALL key, then press the AUTO PUNCH IN

key.)

The time value of the Auto Punch In point (bar/beat/clock) appears and the D-160 will enter the

data edit mode.

2. Use the HOLD/> key or the SHUTTLE dial to move among the digits of the time value (bar/beat/

clock), and use the JOG dial to change the value.

3. Press the STORE key. (The STORE LED lights up.)

4. Press the AUTO PUNCH IN key.

The changed time value (bar/beat/clock) is stored as a new Auto Punch In point, and the Time

Base indication will appear on the display. (The STORE LED turns off.)

5. Press the AUTO PUNCH OUT key. (Or, press the RECALL key, then press the AUTO PUNCH

OUT key.)

The time value of the Auto Punch Out point (bar/beat/clock) will appears and the D-160 will

enter the data edit mode.

6. Use the HOLD/> key or the SHUTTLE dial to move among the digits of the time value (bar/beat/

clock), and use the JOG dial to change their value.

7. Press the STORE key. (The STORE LED lights up.)

8. Press the AUTO PUNCH OUT key.

The changed time value (bar/beat/clock) is stored as a new Auto Punch Out point, and the Time

Base indication appears on the display. (The STORE LED turns off.)

* To check the Auto Punch In/Out points, press the ATUO PUNCH IN/OUT keys

respectively. Or, press the RECALL key, and then press the AUTO PUNCH IN/OUT keys

respectively. The display will indicate the time value (bar/beat/clock) stored for the Auto

Punch In point or Auto Punch Out point.

Executing the erase operation

9. Press the RECORD TRACK select key for any track(s) you wish to erase (up to 16 tracks) so that

the corresponding track(s) enter “READY” mode.

10. Press the ERASE key.

The message “Erase” appears on the display, and “SURE?” flashes.

11. Press the EXECUTE/YES key.

This executes the erase operation. The display will indicate “Wait Erasing!”. When the erase

operation is complete, the message “COMPLETED!” will light along with the message “Erase.”

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

Press the EXIT/NO key, DISP SEL key, or the STOP button to restore the original display.

The sound data in the specified range has been erased.

* To cancel the erase operation while the message “SURE?” is flashing on the display, press

the EXIT/NO key or the STOP key.

* If you wish to cancel the erase operation after you have pressed the EXECUTE/YES key,

press the EXIT/NO key or the STOP button BEFORE the message “COMPLETED!” appears.

* If you cancel the erase operation during the process, nothing will be erased.

Erasing the specified area between ABS 0 and ABS END will not affect the ABS END position.

You can confirm this by pressing the F. FWD button while holding down the STOP button

after the erase operation is complete. You will see no change in the ABS END time on the

display. This means that erasing the specified area has replaced the data with silence,

without moving the ABS END point .

However, the available recording time will increase by the amount of data you erased.

You can check this by pressing the DISP SEL key to see the REMAIN value calculated based

on a single mono track.

3-2. Undo and redo of the erase operation

You can use the Undo and Redo functions for the erase operation.

* After the erase operation is complete, press the UNDO key.

The D-160 will restore the data that existed before you executed the erase operation.

* Press the REDO key after using the UNDO function.

The D-160 will restore the status that existed after you executed the erase operation.

Pressing the UNDO key or the REDO key will execute the corresponding operation

immediately, and the display will indicate the messages “COMPLETED!” and “Undo!” or

“Redo!”, and then return to the previous Time Base indication.

<Note>

You can use the Undo/Redo function while the D-160 transport section is stopped.

You cannot use the Undo/Redo function after one of the following operations:

1. You make a new recording.

2. You perform a new editing operation (such as copy & paste, move & paste, and erase).

3. When the Auto Punch mode is on, and playback or recording passes the Auto Punch In

point.

4. You turn off the power.

5. You use the Program Change function.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

3-3. How to Erase data in its entirety from a specified point up to ABS END:

Storing the erase start point (Auto Punch In point) and the erase end point (Auto Punch Out point)

Refer to “1. Storing memory data,” to set the Auto Punch In/Out points.

Again, we use the procedure to “edit the stored data.”

3, 6

1, 4

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

OUT

END

DISP SEL

HOLD/

AUTO RTN

TIME BASE SEL

COPY

MOVE

PASTE

ERASE

UNDO

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

1. Press the AUTO PUNCH IN key. (Or, press the RECALL key, then press the AUTO PUNCH IN

key.)

The time value of the Auto Punch In point (bar/beat/clock) appears and the D-160 will enter the

data edit mode.

2. Use the HOLD/> key or the SHUTTLE dial to move among the digits of the time value (bar/beat/

clock), and use the JOG dial to change the value.

3. Press the STORE key. (The STORE LED lights up.)

4. Press the AUTO PUNCH IN key.

The changed time value (bar/beat/clock) is stored as a new Auto Punch In point, and the Time

Base indication appears on the display. (The STORE LED turns off.)

5. Press the F.FWD button while holding down the STOP button.

The D-160 will indicate the ABS END (the recording end) point of the selected Program.

* To make sure the data is erased completely, we recommend that you specify a time

after the ABS END point as an erase end point (Auto Punch Out point). To do so, press

the PLAY button following Step 5 so that the ABS time passes the ABS END time. Use the

ABS time, which is now positioned after the ABS END point, as an erase end point.

6. Press the STORE key, then the AUTO PUNCH OUT key.

The ABS END point is stored as a new Auto Punch Out point.

* To check the Auto Punch In/Out points, press the AUTO PUNCH IN/OUT keys

respectively. Or, press the RECALL key, then press the AUTO PUNCH IN/OUT keys

respectively. The display will indicate the time value (bar/beat/clock) stored for the

Auto Punch In point or Auto Punch Out point.

Executing the erase operation

7. Press the RECORD TRACK select key for a track you wish to erase (up to 16 tracks) so that the

corresponding track(s) enters “READY” mode.

8. Press the ERASE key.

The message “Erase” appear on the display, and “SURE?” will flash.

9. Press the EXECUTE/YES key.

This executes the erase operation. The display will indicate “Wait Erasing!”. When the erase

operation is complete, the message “COMPLETED!” will light along with the message “Erase.”

Press the EXIT/NO key, DISP SEL key, or the STOP button to restore the original display.

The sound data between the Auto Punch In point and the ABS END point has been erased.

This area does not contain a recording, and the available recording time on the disk

(REMAIN value) increases.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

* To cancel the erase operation while the message “SURE?” is flashing on the display, press

the EXIT/NO key or the STOP key.

* If you wish to cancel the erase operation after you have pressed the EXECUTE/YES key,

press the EXIT/NO key or the STOP button BEFORE the message “COMPLETED!” appears.

* If you cancel the erase operation during the process, nothing will be erased.

Although erase is executed on other than all tracks (mono track or multiple tracks), the ABS

END which is the final recording position of the program, will not be affected (ABS END will

be affected, however, if it is erased as shown below).

After execution of erase, upon confirming the ABS END time by simultaneously pressing

the STOP and F. FWD buttons, you will notice that it is the same ABS END as that before

erasing. However, if REMAIN is put on display by pressing the DISP SEL key, REMAIN (disk

remaining time) can be confirmed to have increased by the erased time converted to mono

track. In order to shift the ABS END forward, carry out the previous step by specifying all

recorded tracks.

When there is a recording on tracks 1~6 of a certain program as shown below, if it is located

to ABS END, this located ABS END will be at final recording point of tracks 3 and 4, and the

time will always be shown in the display.

Therefore, although tracks 1 and 2 or 5 and 6 of a program with such a content is erased

(from any point to ABS END), ABS END that is always displayed will be the track 3 and 4

time. However, if tracks 3 and 4 are erased, ABS END will change.

ABS END of Track 1 and 2

ABS END of Track 5 and 6

ABS END of Track 3 and 4

ABS 0

Track 6

Track 5

Track 4

Track 3

Track 2

Track 1

Erasing area

Any point

ABS END

3-4. Undo and redo of the erase operation

You can use the Undo and Redo functions for the erase operation.

* After the erase operation is complete, press the UNDO key.

The D-160 will restore the data that existed before you executed the erase operation.

* Press the REDO key after using the UNDO function.

The D-160 will restore the status that existed after you executed the erase operation.

Pressing the UNDO key or the REDO key will execute the corresponding operation

immediately, and the display will indicate the messages “COMPLETED!” and “Undo!” or

“Redo!”, and then return to the previous Time Base indication.

<Note>

You can use the Undo/Redo function while the D-160 transport section is stopped.

You cannot use the Undo/Redo function after one of the following operations:

1. You make a new recording.

2. You perform a new editing operation (such as copy & paste, move & paste, and erase).

3. When the Auto Punch mode is on, and playback or recording passes the Auto Punch In

point.

4. You turn off the power.

5. You use the Program Change function.

100

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Edit function)

3-5. Erasing specific data (Program erase)

Here, erase all data recorded in any program that is no longer necessary.

Unlike the "erasing the program" explained in "Recording/Playback", the program number

will remain intact and other settings will all be in the initial state same as when the New

Program was made (at completion of erase, ABS 0=ABS END).

Therefore, the tempo map setting and program title will be in the initial figures.

<Note>

Note that the UNDO/REDO function cannot be used at Program Erasing.

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

1. Press the STORE key while holding down the HOLD/> key.

The D-160 will enter the Program Setup mode, and display the message “Select PGM!”, and then

the current Program number and title. (The Program number and “SURE?” will flash.)

Example:

“Select PGM!”

“P02 [*****”

(02 flash, 02 is the current program number)

2. Turn the JOG dial to select the number of a Program you wish to erase.

The selected Program number will flash. (Can not use "New Program?.")

3. Press the ERASE key.

The message

“Erase PGM**?”

(where, ** is the selected Program number) appears on

the display, and “SURE?” will flash.

4. Press the EXECUTE/YES key.

When the erase operation is completed, the display changes to the

“Title Edit PGM**?”

menu in Setup mode, where you can name the Program from which you erased the data.

* To name the Program, follow the explanation on page "147" regarding the “2-4. Title Edit

PGM?” menu in Setup mode.

If you do not wish to name the Program, press the STOP button or the EXIT/NO key.

The display will change to the ABS indication, with the Program number unchanged.

The title of the Program is erased, and the Program will use a temporary title.

101

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

Saving and loading data

The D-160 allows you to select the data (audio data and Setup data) from a current

Program and save it to a DAT machine as an S/PDIF digital signal or to an adat machine

as an adat digital signal, or save it to a SCSI device.

You can also re-load the saved data to the D-160. In particular, using a SCSI device

enables you to save and load the data of all Programs (up to 99 Programs), as well as an

individual Program. These save and load functions are convenient when you wish to

store Programs (complete or in progress) temporarily to a DAT, adat, or SCSI device to

clear enough space on the internal hard disk to make new recordings.

**********About saved and loaded data**********

The data format and time taken to save or load data varies depending on how you save or

load the data as follows:

S/PDIF digital signal (You can save and load each Program individually.):

Audio data will be output following a pilot signal of about five seconds.

In the S/PDIF digital signal format, two tracks of audio data (the black part in the diagram)

are input/output at a time (total of eight times, or twelve times if additional tracks are

included). Therefore, saving/loading one Program takes eight times longer (or twelve times

including the additional tracks) than the Program’s actual recording time (time duration

from ABS 0 to ABS END). When a pilot signal and Setup data (the grey part in the diagram)

are output or input, you will hear the beep sound, which enables you to confirm the position

of those signals.

Tr 1&2

Tr 3&4

Tr 21&22

Tr 23&24

adat digital signal (You can save and load each Program individually.):

Audio data will be output following a pilot signal of about five seconds.

In the adat digital signal format, eight tracks of audio data (the black part in the diagram)

are input/output at a time. Therefore, saving/loading one Program takes twice long (or

three times including the additional tracks) as the Program’s actual recording time (time

duration from ABS 0 to ABS END). When a pilot signal and Setup data (the grey part in the

diagram) are output or input, you will hear a beep sound, which enables you to confirm the

position of those signals.

Tr 9 & 10

& 11 & 12

& 13 & 14

& 15 & 16

Tr 17 & 18

& 19 & 20

& 21 & 22

& 23 & 24

Tr 1 & 2 &

3 & 4 & 5

& 6 & 7 &

SCSI (You can save and load each Program individually or all Programs at once.):

Only SCSI devices allow you to save the song data of all setup Programs. All sixteen tracks (24

tracks including the additional tracks) of audio data (the black part in the diagram) will be

input/output at a time. Therefore, the time taken to save or load one Program is much

shorter than an operation using a DAT or adat. No pilot signal or beep sound will be recorded

during the operation.

Tr 1 & 2 & 3 & 4 & 5 & 6 & 7

& 8 & 9 & 10 & 11 & 12 & 13

& 14 & 15 & 16 & 17 & 18 &

19 & 20 & 21 & 22 & 23 & 24

Program 1 (P01)

Program 2 (P02)

Program 99 (P99)

102

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

* The following items can be saved and loaded as song data:

Memory data (CLIPBOARD IN/OUT, AUTO RTN START/END, AUTO PUNCH IN/OUT)

Time Base (ABS, MTC, or BAR/BEAT/CLK)

Setup mode:

* Time signature setting (BAR BEAT), * Tempo setting, * Click On/Off setting

* Preroll Time setting, * Midi Sync Out setting, * MTC Frame Rate setting

* MTC Offset setting, * MTC Offset Mode setting, * Rec Protect On/Off setting

* Slave Mode on/off setting, * Slave Type setting, * FS (sampling frequency) setting

* The following items cannot be saved or loaded as song data:

Auto Play mode and Auto Return mode On/Off

Vari-pitch mode On/Off, and pitch data

Setup mode:

* Digital In setting, * Digital Out setting, * Bar/Beat Resolution On/Off setting

* Device ID setting

<Notes>

* You can save or load only one Program to and from a DAT or adat at a time.

Use a SCSI device to save or load all Programs.

* The D-160 can only save and load data to and from digital devices that support non-

compression recording, and S/P DIF or adat format digital recording functions.

Basically, any device that supports the adat format can be used for the D-160’s saving and

loading operation.

However, for the S/P DIF format, you cannot use an MD or DCC that employs compression

recording system, a CD-R machine that automatically corrects the interval between Programs,

or other devices that automatically change the sampling rate. Devices with SCMS can be

used if they satisfy the conditions described above.

Basically, any digital device that supports non-compression recording, and the S/P DIF or

adat formats, should be able to save and load the D-160’s data correctly. However, some

devices may not, due to the occurrence of multiple errors. The following Fostex models

have been tested and approved for the save and load operation:

FOSTEX: D-15, D-10, D-5

103

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

1. Saving the data using DATA OUT

* Restore the initial settings on the D-160.

* Set the same sampling rate on the external digital device and the D-160.

Connecting an external device

Connect DATA OUTPUT 1-8 connector of the D-160 to the digital input connector on the

external digital device.

<Notes>

* The D-160 has DATA OUT connectors for an S/P DIF digital signal (OPTICAL) and for an adat

digital signal. These connectors have the same shape but carry different information.

* Use the DATA OUTPUT 1-8 connector to save data. Do not use the DATA OUTPUT 9-16

connector.

* At save/load using DAT and adat, independent save/load in 8 track units is possible.

In this case, the data in 8 track units are not distinguished as track 1~8 or 9~16 but simply

handled as eight track data. Therefore, because this 8 track data is compatible with D-90 if it

is in 8 track units (any one combination of 1~8, 9~16 or 17~24), data saved from D-160 can

be loaded in tracks 1~8 of the D-90. In this case, data in the tracks which were not loaded will

remain intact.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

TO RAIN OR MOISTURE.

D-160

AVIS

ANALOG OUT

ANALOG IN

3 2

DATA

1~8

SCSI

MIDI

OPTICAL

INPUT

9~16

OUTPUT

9~6 1~8

INPUT

OUTPUT

THRU

DATA OUTPUT 1-8

DIGITAL IN

External Digital Equipment (DAT or RD-8 or Adat)

• If the external device has only COAXIAL type (RCA) digital I/O connectors, connect an

optional COP-1 (optical/coaxial converter) to use an S/P DIF digital signal.

• Connecting both output and input connectors on the D-160 to the input and output

connectors on the external digital device respectively may generate a digital loop.

Refer to “4-3. Connecting a digital mixer” on page "65" for more information.

Setting up an external device

1. Set the same sampling rate to that of the D-160.

2. Select digital input on the external device so that the external device will accept a digital signal.

On some external devices, you may have to set up so that the external device will synchronize

with the incoming digital signal. For example, if you are using a Fostex RD-8, select “DIGITAL IN”

and set “Clock Source (external sync signal)” to “Word Optical (adat).”

<Note>

If the external device does not accept the digital signal or if you notice digital noise, check

the connection, cabling, and the settings of the D-160 and the external device.

* Refer to the instruction manuals that came with any external digital device for details.

Executing the save operation

Use the “Save PGM?” menu in Setup mode.

* Output format available: adat, DAT, SCSI

* Programs available: P1 - P99

* You can save one Program at a time.

104

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

1. Press the DISP SEL key to select “SETUP” (“SETUP” will flash), then press the EXECUTE/YES

key. (“SETUP” will light up.)

The D-160 enters Setup mode.

2. Use the JOG dial to select “Save PGM?” (“?” will flash.).

3. Press the EXECUTE/YES key.

The message “Save Device?” and an indication of the digital signal to be saved (“DAT,” “adat,” or

“SCSI”) will flash on the display.

4. Rotate the JOG dial to select a type of digital signal format to be used for the save operation.

Selecting “adat” will save data in the adat digital signal format.

Selecting “DAT” will save data in the S/P DIF digital signal format.

Select “SCSI” if you are saving or loading data via SCSI. The following operation will be that when

"adat" or "DAT" is selected for "Save Device?."

5. Press the EXECUTE/YES key.

Selection of the digital signal format for the save operation will be confirmed, and the existing

Program numbers will flash on the display.

6. Rotate the JOG dial to select a Program to save.

You can select any existing Program (up to 99) to save.

7. Press the EXECUTE/YES key.

The duration of the selected Program appears on the display so that you can edit the time

shorter or longer, as necessary. Time length recorded in the selected program will be displayed

and the time can now be edited. Normally, it is saved in the time displayed but at this stage, it is

also possible to save in any shorter time or by setting the time longer than what is actually

recorded. This function is provided for the purpose of saving in a short section of insufficient

tape capacity. Maximum saving time is 60 minutes.

8. Press the EXECUTE/YES key again.

“Save Trk? 1-16” (“1” is flashing) appears on the display and you can select tracks to save.

While “1” is flashing, rotate the JOG dial to select “1”->”9”->”17.” To select “8”->”16”->”24,” use

the SHUTTLE or press the HOLD/> key to flash “16” and rotate the JOG wheel.

You can select one of the following track combinations: “1-8,” “1-16,” “1-24,” “9-16,” “17-24.”

(Tracks 17-24 are additional tracks. Selecting “1-24” or “9-24” will cause the additional tracks to

be saved along with the real tracks.)

9. Press the EXECUTE/YES key.

“Rec Start DAT!” (Start recording on the DAT) or “Rec Start adat!” (Start recording on the adat)

appears on the display, and “SURE?” flashes.

10. Confirm that the external device is syncing with the digital input signal, and start recording on

the external device (DAT or adat).

Setting a START-ID (DAT) or a locate point at the recording start point will facilitate future

loading operations.

11. Confirm that the recording on the external device has started, and press the EXECUTE/YES

key. (“REMAIN” will light.)

The save operation starts, and the time required for the save operation appears on the display

and a few seconds later, it will start counting down. This few seconds delay is due to the pilot

signal which is recorded to mark the beginning of the Program to facilitate future load operation.

Therefore, the actual save operation starts when counting down starts.

Two tracks are saved each time in the order of Track 1 and 2, 3 and 4, etc. to a DAT machine.

Eight tracks are saved each time in the order of Track 1-8, 9-16, etc. to an adat machine.

The level meter indication during save of DAT will always be for only tracks 1 and 2 and always

for tracks 1~8 in save of adat.

12. When the save operation is complete, “COMPLETED!” flashes on the display.

13. Press the STOP button or the EXIT/NO key to quit the Setup mode. The display will return to the

previous time base indication.

• To cancel the operation or restore the indication shown before you pressed the EXECUTE/YES key, press the

STOP button or the EXIT/NO key. Pressing one of these keys repeatedly takes you to the previous layer, finally

quitting the Setup mode, and the display will return to the previous time base indication. If you press the STOP

button or the EXIT/NO key any time after you execute the save operation but before it is complete, the saved song

data will be invalid.

* Refer to page "168" for more information on the “2-23. Save PGM?” menu in Setup mode.

105

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

2. Loading the data using DATA IN

* Restore the initial settings on the D-160.

* Set the same sampling rate on the external digital device and the D-160.

Connecting the external device

Connect DATA INPUT 1-8 connectors of the D-160 to the digital output connectors on the

external digital device.

<Notes>

* The D-160 has DATA INPUT connectors for an S/P DIF digital signal (OPTICAL) and for an adat

digital signal. These connectors have the same shape but carry different information.

* Use the DATA INPUT 1-8 connector to load data. Do not use the DATA INPUT 9-16 connector.

* When save/load using DAT and adat, independent save/load in 8 track units is possible. In

this case, the data in 8 track units are not distinguished as track 1~8 or 9~16 but simply

handled as eight track data. Therefore, as this 8 track data is compatible with D-90 if it is in 8

track units (any one combination of 1~8, 9~16 or 17~24), data saved from D-160 can be

loaded in tracks 1~8 of the D-90. In this case, data in the tracks which was not loaded will

remain intact.

D-160

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

TO RAIN OR MOISTURE.

AVIS

ANALOG OUT

ANALOG IN

3 2

DATA

1~8

SCSI

MIDI

OPTICAL

INPUT

9~16

OUTPUT

9~6 1~8

INPUT

OUTPUT

THRU

DATA INPUT 1-8

DIGITAL OUT

External Digital Equipment (DAT or RD-8 or Adat)

• If the external device has only COAXIAL type (RCA) digital I/O connectors, connect an

optional COP-1 (optical/coaxial converter) to use an S/P DIF digital signal.

• Connecting both output and input connectors on the D-160 to the input and output

connectors on the external digital device respectively may generate a digital loop.

Refer to “4-3. Connecting a digital mixer” on page "65" for more information.

Setting up an external device

1. Setup the external device so that it can output a digital signal.

2. Locate the beginning of the pilot signal recorded in the saved data.

* Refer to the instruction manual that came with your external digital device for details.

Executing the load operation

You will use the “Load PGM ?” menu in Setup mode.

* Input format available: adat, DAT, SCSI

* Programs available: P1 - P99

* You can load one saved Program at a time.

1. Press the DISP SEL key to select “SETUP” (“SETUP” will flash) and press the EXECUTE/YES

key. (“SETUP” will light up.)

The D-160 will enter the Setup mode.

2. Use the JOG dial to select “Load PGM ?” (“?” will flash.).

3. Press the EXECUTE/YES key.

The message “Load Device?” and the type of digital signal to be loaded (“DAT,” “adat,” or “SCSI”)

will flash on the display.

106

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

4. Rotate the JOG dial to select the type of digital signal format to be used for the load operation.

Selecting “adat” will load data in the adat digital signal format.

Selecting “DAT” will load data in the S/P DIF digital signal format.

Select “SCSI” if you are loading data via SCSI. The following operation will be that when "adat" or

"DAT" is selected for "Load Device?."

5. Press the EXECUTE/YES key. (“SURE?” flashes.)

Selection of the digital signal format for the load operation will be confirmed, and the existing

Program numbers will flash on the display.

• If digital signal is being input correctly, a red “DIGITAL” indicator will light up on the

display. If the red “DIGITAL” indicator flashes, check the connection, cabling, and the

settings of the D-160 and the external device.

<Notes>

* If the sampling rate of the incoming S/P DIF digital signal is different, the FS indicator

in the display (44.1kHz or 48kHz) will flash to warn you.

* Even if the sampling rate of the incoming adat signal is different, no warning will

appear. Use caution when you set the sampling rate.

6. Rotate the JOG dial to select a Program into which to load data.

You can select any existing Program (from up to 99).

• If you select a Program that already contains data and execute the load operation, the

existing data will be overwritten by the new data.

If you do not wish to overwrite any data in any current Program, use the JOG dial to

select “New PGM” to execute the load operation. You can do this only when the number

of existing Programs is 99 or less and the hard disk has enough free space to

accommodate the new data.

<Note>

Once you start loading, all existing song data in the Program will be erased, even if you cancel

loading during the operation, and new song data and tempo map data etc. (data up to the

point at which you canceled the operation) will be recorded. For example, if you load two

minutes of song data into a Program that already contains a song of six minutes, the new

song data will be recorded and the old song data will be erased in its entirety. (ABS END is

“two minutes.”) Bear this in mind and be certain to check the Program before you execute

the load operation.

7. Press the EXECUTE/YES key.

Now you can select tracks into which to load.

Use the SHUTTLE or the HOLD/> key to flash the characters, and use the JOG dial to select a

desired number. Select one of the following track combinations: “1-8,” “1-16,” “1-24,” “9-16,”

“17-24.”

8. Press the EXECUTE/YES key. (“SURE?” flashes.)

9. Press the EXECUTE/YES key again.

“Play DAT!” (Start playing the DAT) or “Play adat!” (Start playing the adat) appears on the

display.

10. Play the corresponding external device (DAT or adat).

The load operation starts when the D-160 accepts the incoming digital signal. The time required

for the load operation appears on the display and starts counting down. Two tracks are loaded

at a time from a DAT machine in the following order: Track 1 and 2, 3 and 4, etc. from a DAT

machine. Eight tracks are loaded each time in the order of Track 1-8, 9-16, etc..

11. When the load operation is complete, “COMPLETED!” flashes on the display.

12. Press the STOP button or the EXIT/NO key to quit Setup mode.

The display will indicate the time base set for the loaded Program.

• To cancel the operation or restore the indication shown before you pressed the EXECUTE/YES key, press the

STOP button or the EXIT/NO key. Pressing one of these keys repeatedly takes you to the previous layer, finally

quitting Setup mode, and the display will return to the previous time base indication. If you press the STOP button

or the EXIT/NO key any time after you execute the load operation but before it completes, the loaded song data will

be largely invalid, though some portion may play back.

107

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

<Note>

Do not remove the optical cable or perform any other operation that would disconnect

the S/P DIF signal until the session is complete. Otherwise, the D-160 will generate noise,

and affect the connected device.

3. Saving the data using SCSI

SCSI devices you can use

Please use the following recommended SCSI devices that have already been performance

tested.

Recommended SCSI devices that have been tested for operation (as of January ‘97)

LF-3200 (Matsushita)

<MO>: 230MB

<MO>: 540MB

MOS331 (Olympus)

M2512A (Fujitsu)

OMD-7060 (Konica)/540MB only

zip 100 (IOMEGA)/100MB

jaz (IOMEGA)/1GB

Removable hard disk

ezflyer (SyQuest)/230MB

EZ135 (SyQuest)/135MB

SyJet (SyQuest)/1.5GB

LF-1000 (Matsushita)/640MB

FireBall 1080S (Quantum)/1.08GB

<PD>

Fixed hard disk

* Either disk should have SCSI-2 specifications.

<Note>

These SCSI devices have already been tested for performance at Fostex.

However, any product lot includes variance in quality.

The test at Fostex does not include inspection for such variance. When you use external

SCSI devices, check the operation carefully. Fostex is not liable for any damage (data loss or

damage) caused by using the D-160 with external SCSI devices.

* Restore the default settings on the D-160.

Connecting a SCSI device

Refer to the diagram to connect a SCSI device to a D-160.

<Notes>

* First, turn off the power to all the devices before you connect them.

* Connect only one SCSI device to the D-160.

You cannot chain SCSI devices. Install a SCSI terminator on the other connector. (If the

SCSI device has a termination switch, be suer to turn the switch ON to terminate the

device.)

* The D-160 will detect the SCSI ID number set on the connected device, and show it on the

display. (Refer to the SCSI device manual for setting the ID number.)

* You must format the SCSI disk after you connect it to the D-160. Refer to the “Formatting”

section on the next page for the formatting procedure.

108

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

CAUTION

D-160

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SHOCK. DO NOT EXPOSE THIS EQUIPMENT

:RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

TO RAIN OR MOISTURE.

AVIS

ANALOG OUT

ANALOG IN

3 2

DATA

1~8

SCSI

MIDI

OPTICAL

INPUT

9~16

OUTPUT

9~6 1~8

INPUT

OUTPUT

THRU

External SCSI Equipment

Formatting a SCSI disk

About formatting a SCSI disk:

You will format a SCSI disk in the “Disk Format?” menu in Setup mode.

During formatting, the D-160 automatically checks the performance of the connected SCSI

device, selects and displays an appropriate format type from TYPE 0 - TYPE 2 (TYPE 2 is

selected as a default setting). The user can manually select the desired type.

SAVE/LOAD

Available

TYPE recording

time

Real time playback

You need to select the SCSI drive

as the current drive.

Real time recording

You need to select the SCSI drive

as the current drive.

It takes the same time to save

and load data using

Remarks

TYPE 0 and TYPE 2.

<Short>

You cannot specify TYPE 0.

The measuring function of the D-160 will

select this option.

However, Fostex will not guarantee

the operation. Refer to "Notes on

real time recording/playback" for

more information.

However, Fostex will not guarantee

the operation. Refer to "Notes on

real time recording/playback" for

more information.

TYPE 0

TYPE 2

Depends on

the disk.

<Long>

Depends on

the disk.

We recommended that you use TYPE 2

The D-160 will reject any attempt to

set it in recording mode.

<Possible but the sound will skip> format if you are using a SCSI drive only

to save and load data.

TYPE 3 is used to perform

simple formatting. Read the

notes below before proceeding

with the operation.

The merit of TYPE 3 is that a shorter

formatting time is required, compared to

TYPEs 0 and 2.

The degree of sound skipping will

For example, if you are using an MO disk

depend on the result of automatic

that has already been formatted for DOS

measurement with TYPE 0 and 2.

Depends on

the disk.

<Notes>

The D-160 will reject any attempt to

set it in recording mode.

or MAC, usually there are no bad blocks

* TYPE 3 format will format the

disk, assuming that the entire

area in the disk is available, and

will not be able to identify the

area actually available.

TYPE 3

on the disk. Using TYPE 3 format will be

TYPE 0: Skip -> less

quicker than TYPEs 0 and 2.

TYPE 2: Skip -> frequent

The D-160 will not select this type using

the measuring function. Only users can

specify this type.

* Bad blocks in the disk cannot

be selected. This may later

cause the sound to skip.

Logically, you can perform real time recording/playback if your case is described under the <Possible> category in

the table shown on the above. However, the sound might skip, depending on the condition of the connected SCSI

drive disk.

The D-160 performs experimental reading and writing at two points on the disk to measure the performance of the

connected SCSI device, and based on the results, such as the response time of the disk, it will determine the format

type (TYPE 0-2). Therefore, for parts of the disk other than the two measured points, you do not know if the disk

will maintain adequate speed to realize real time recording/playback.

It might be possible that the sound skips during real time recording or playback within the untested parts.

Measuring two points for performance can indicate tell whether or not the disk is reliable, but this is only an

“index.” Fostex will not guarantee the operation of the SCSI disk.

109

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

Although the following chart presents the SCSI disk formatting time in accordance to

each format type (measured by Fostex), please refer to this, as necessary, only for an

approximate formatting time.

Formatting Time

TYPE 0, 2

TYPE 3

SyJet (1.5GB)

FireBall (1GB)

PD (640MB)

MO (230MB)

MO (540MB)

EZ135 (135MB)

ezflyer (230MB)

zip (100MB)

Approx. 20 minutes

Approx. 16 minutes

Approx. 50 minutes

Approx. 5 seconds

Approx. 22 seconds

Approx. 12~15 minutes Approx. 27 seconds

Approx. 14~17 minutes Approx. 22 seconds

Approx. 3 minutes

Approx. 6 minutes

Approx. 4 minutes

Approx. 15 minutes

Approx. 4 seconds

Approx. 5 seconds

Approx. 8 seconds

Approx. 5 seconds

jaz (1GB)

1. Connect the SCSI device to the D-160 and turn the power on to the both machines.

2. If you are using a removable disk, insert the disk into the drive.

To remove the inserted disk, press the STOP button and the EXIT/NO key on the D-160

simultaneously.

You cannot remove the disk from the SCSI device.

3. Press the DISP SEL key to select the Setup mode, and press the EXECUTE/YES key.

The Setup mode menu appear on the display.

4. Turn the JOG dial to select “Disk Format?” (“?” flashes), and press the EXECUTE/YES key

again. “Disk Format IDE” (“IDE” flashes) appears.

CAUTION: If format is executed while "IDE" is blinking, the internal IDE hard disk will be

formatted and data in the IDE hard disk will be lost.

5. Rotate the JOG dial to display the flashing “SCSI” and press the EXECUTE/YES key. The ID

number and name of the connected SCSI device appear on the display, and “?” and “SURE?”

flash.

6. Press the EXECUTE/YES key.

The D-160 indicates “Please Wait!” followed by the results of a performance measurement of the

connected SCSI device, and flashes an appropriate format type and the message “SURE?”.

7. Press the EXECUTE/YES key.

“REMAIN” lights up and formatting starts.

As the formatting operation progresses, the size of the area to be formatted on the disk will count

down on the display. (For example, indication “-125MB” will count down to “0MB”.)

Also, when the formatting operation starts, all the FL indicators (for Tracks 1-16) at level ∞ of

the level meters light up. As the formatting operation progresses, these indicators will be turned

off from Track 16. This condition indicates that the disk is being formatted correctly.

When formatting is complete, “COMPLETED!” will appears and all the FL indicators will turn off.

8. Press the EXIT/NO key or the STOP button to quit the Setup mode.

The D-160 returns to the ABS display of the Program that was selected before it entered Setup

mode.

In addition to the formatting procedure mentioned above, you can also use the following

steps to format an unformatted disk.

Install an unformatted fixed disk or removable disk, and go to the “2-21. Drive Sel.?” menu

in Setup mode. Change the current drive from “IDE” to “SCSI”.

The D-160 will recognize that the SCSI disk is not formatted and automatically enter the

“2-24. Disk Format ?” menu in Setup mode, where you can follow the procedure mentioned

above to format the disk.

110

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

Name of data saved in the SCSI disk:

The D-160 manages data in the internal IDE hard disk using the name “Program” (such as

Program 1, Program 2, etc. which appears on the display as P01, P02, etc.). Data on the

SCSI disk is termed “Song” or “Backup” to differentiate it from Program data.

When you format a SCSI disk, Song #1 is created on the disk. When you switch the

current drive from “IDE” to “SCSI,” the D-160 will display “S01.”

When you save data from the D-160 to the SCSI disk, the data is treated as “Song” or

“Backup,” depending on how you saved the data.

How to save data

Name

Display

When one or all Programs were saved to one fixed

disk or removable disk.

Song

"S**"

When one Program was saved to multiple

removable disks.

Backup

"B**"

<Note>

You can use multiple removable disks, but not multiple fixed disks to save data.

Saving data of an individual Program

You will use the “Save PGM ?” menu in Setup mode.

* Input format available: adat, DAT, SCSI

* Programs available: P1 - P99, ALL

* You can save one Program or all Programs at once.

1. Press the DISP SEL key to select “SETUP” (“SETUP” will flash), and then press the EXECUTE/

YES key. (“SETUP” will light up.)

The D-160 will enter the Setup mode.

2. Use the JOG dial to select “Save PGM?” (“?” will flash.).

3. Press the EXECUTE/YES key. (“SAVE” lights up.)

The indication of the type of digital signal to be saved will flash on the display.

SETUP

44.1kHz

SAVE

∞

4. Rotate the JOG dial to select a flashing “SCSI.”

5. Press the EXECUTE/YES key. (“SURE?” flashes.)

The external digital device is set to “SCSI,” and the existing Program numbers will flash on the

display. (e.g.: “P02 [current title...” with “02” flashing.)

6. Rotate the JOG dial to select a Program to save.

You can select any existing Program individually or all Programs (Save All). (Refer to the next

section for information on saving all Programs.)

As mentioned previously, the display indication differs as follows depending on whether the

selected Program to save requires only one removable disk or multiple disks.

* If you have selected a Program that has only the Program number and title indication on the

display:

e.g.: P02 [#******* (#***** is current title)

This indication means that saving Program P02 requires only one SCSI fixed or removable disk.

111

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

* If you have selected a Program that has the Program number and title indication, plus “nD”

(n=number) on the display:

e.g.: P01[********** ]2D (***** is title)

This indication means that saving Program 01 requires multiple SCSI disks.

“2D” in this example means that two disks are required.

When using the hard disk, if the program data to be saved is larger than the hard disk capacity,

"- ***MB" (insufficient capacity) will be displayed.

Also, if the EXECUTE/YES key is pressed while this is on the diaplay, "DISK FULL" will appear in

the display.

7. Press the EXECUTE/YES key. (“SURE?” flashes.)

The D-160 performs the save operation differently depending on the selected Program.

* If you have selected a Program that requires only one disk to save:

The current Song number (“S01”) in the SCSI disk appears on the display.

Pressing the EXECUTE/YES key at this point will start the save operation. “REMAIN” will light up,

then the D-160 will display “P01>>S01-***MB”. “-***MB” indicates the remaining amount of

data to be saved, which will count down as the save operation is in progress.

* If you have selected a Program that requires multiple disks:

The save operation will start right away. “REMAIN” will light up, then the D-160 will display

“P01>>B01-***MB”. (The indication of the remaining amount of data to be saved will count down

as the save operation is in progress.) The Song number will automatically change to the Backup

number “B01.”

When saving to the first disk is complete, “Insert Disk 2” (Insert the second disk!) appears on the

display, and the D-160 will automatically eject the disk. When you insert the second disk, the D-160

will continue the save operation with the same Backup number. In this way, when the entire save

operation is complete, the D-160 will display an illuminated “COMPLETED!”, then change to the

Time Base of the saved Program.

Pressing the STOP button or the EXIT/NO key will turn the “COMPLETED!” indication off.

<Notes>

* You cannot abort a save operation on the SCSI device while it is in progress.

* To enter a title for a SCSI disk, go to “2-20. Drive Sel.?” menu in Setup mode and change

the current drive to “SCSI,” and then go to “2-4. Title Edit?” menu in Setup mode to enter

the title. Normally, the title of the program in the internal IDE hard disk will be directly

copied as the title of the song in the SCSI disk or the title of the backup data.

* If you try to save data to multiple disks or try to save all Program data to one disk, and

if those disks already have data recorded, the message (“B01[*****]DEL” or

“S01[*****]DEL”) will appear on the display, asking if you wish to erase the Backup data or

Song data already recorded on the disk, and “SURE?” will flash.

Subsequently, if you wish to erase the data, press the EXECUTE/YES key is and save will

start after erasing the data. If you do not want to erase the data, rotate the JOG dial and

select "Eject" while "SURE?" is blinking, and then press the EXECUTE/YES key and remove

the disk. The disk can also be removed after emerging from the SETUP mode by pressing

the STOP button or the EXIT/NO key. In this case, the press the EXIT/NO key while pressing

down on the STOP button when in other than the SETUP mode.

Saving all Programs (Save ALL)

1. Follow Steps 1 through 5 of the “Saving an individual Program” procedure.

2. Use the JOG dial to select “Save ALL?” (“?” flashes.).

Selecting “Save All?” will cause the following display to appear.

Save All? (nn/nn) (nn=number)

112

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

The number on the right of the slash (/) is the number of all Programs, and the number on the

left is the number of Programs that can be saved.

For example, “03/03” means that all three Programs can be saved. “01/03” means that one

Program out of three Programs can be saved.

“00/03” means that no Programs can be saved. If you press the EXECUTE/YES key at this point,

“Void Command!” appears and you cannot proceed with the save operation.

If you have selected “Save All”, you cannot use multiple disks to save. In this case, chose the save

operation for an individual Program.

3. Press the EXECUTE/YES key (“SAVE” light up.)

Data will be saved as Song data. Therefore, Program 1 (P1) on the internal hard disk will be saved

as Song 1 (S1), Program 2 (P2) as Song 2 (S2).

After the save operation is complete, “COMPLETED!” lights up. Press the STOP button or the

EXIT/NO key to return to the previous Time Base display.

<Notes>

* You cannot abort a save operation while it is in progress.

* To enter title for a SCSI disk, go to “2-20. Drive Sel.?” menu in Setup mode and change

the current drive to “SCSI,” then go to “2-4. Title Edit?” menu in Setup mode to enter

the title.

<Note>

If an error occurs during execution of save and "Error 35" appears in the display, carry out

the following steps:

1^{. Press the EXIT/NO key.}

"Retry?" will appear in the display.

2^{. If save is to be executed again, press the EXECUTE/YES key upon display of "Retry?."}

Save will be executed again.

If ALL save was carried out in this process, save will be executed again from where the

error occurred. Also, if several disks are used for the save, it will save again from the

head of the disk in which the error occurred.

3^{. If it is to be canceled without executing save, press the EXIT/NO key upon display of}

"Retry?."

Loading Song data

Use the “Load PGM?” menu in the Setup mode to load Song data.

* Input format available: adat, DAT, SCSI

* Programs available: P1 - P99, ALL

* You can save one Program or all Programs at a time.

1. Press the DISP SEL key to select “SETUP” (“SETUP” will flash) and press the EXECUTE/YES

key. (“SETUP” will light up.)

The D-160 will enter the Setup mode.

2. Use the JOG dial to select “Load PGM?” (“?” will flash.).

3. Press the EXECUTE/YES key. (“LOAD” will light.)

An indication of the type of the digital signal to be loaded will flash on the display.

SETUP

44.1kHz

∞

LOAD

4. Rotate the JOG dial to select a flashing “SCSI.”

5. Press the EXECUTE/YES key.

The external digital device is set to “SCSI,” and the existing Song numbers will flash on the

display. (i.g.: “S01[*******” with “01” flashing.)

113

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

6. Rotate the JOG dial to select the data to load.

You can choose to load any existing Song individually or all Songs collectively.

The display indication differs as follows depending on whether you selected an individual Song

number or all Song numbers.

* If you have selected an individual Song:

e.g.: You have selected Song 2.

S02[***** (**** is title)

* If you have selected all Songs:

e.g.: Load ALL (**/**) (**=**)

7. Press the EXECUTE/YES key. (“SURE?” flashes.)

Now you can select a Program to load data into.

* If you have selected an individual Song number:

The D-160 will indicate the destination Program number on the internal hard disk. Use the JOG

dial to select a desired destination Program number into which to load data.

If you select a destination Program that already has data, pressing the EXECUTE/YES key will

execute the load operation and the loaded data will overwrite the existing data in the Program.

If you do not want to overwrite the existing data, use the JOG dial to select “New PGM.”

* If you have selected “Load All?(**/**):

The D-160 will indicate the destination Program number on the internal hard disk. Use the JOG

dial to select a desired destination Program number into which to load data.

If the destination hard disk already contains data and you select a Program, “DEL” (Delete)

appears following the Program number.

This is because the “Load All” operation will first erase any Program data on the disk before

loading Song data.

Pressing the EXECUTE/YES key at this point will cause “Delete All PGM?” (deleting all Programs)

to appear, and then “SURE?” will flash.

8. Press the EXECUTE/YES key.

Song data will be loaded to the selected Program.

For example, if Song 1 (S01) is loaded into Program 1 (P01), the D-160 will display “S01>>P01-

***MB” and “REMAIN” will light up. The remaining data to be loaded will count down on the

display as the load operation progresses.

During the all Program load operation, Songs are loaded into Programs sequentially; that is, Song

1 into Program 1, Song 2 into Program 2. (The display changes will correspond to this sequence:

“S01>>P01-***” --> “S02>>P02-***”, etc.)

When the load operation is complete, “COMPLETED!” will light and the D-160 will display the

Time Base that was shown before the unit entered the Setup mode.

9. Press the STOP button or the EXECUTE/YES key, and “COMPLETED!” will turn off.

<Notes>

* You cannot abort a load operation on a SCSI device while it is in progress.

* To enter a title for the SCSI disk, go to “2-20. Drive Sel.?” menu in Setup mode and change

he current drive to “SCSI,” then go to “2-4. Title Edit?” menu in Setup mode to enter the

title.

Loading Backup data

As an example here, we will load the data of a Program saved onto two removable disks.

1. Insert the first disk (Disk-1) into the SCSI device.

2. Follow Steps 1-4 of the “Loading Song data” procedure.

3. Select “SCSI” and press the EXECUTE/YES key. (“LOAD” lights up).

The external digital device is set to “SCSI”. The display flashes the number of the existing Backup

data in the SCSI disk, and then indicates that the first disk has been inserted.

114

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

B01[******]D1 (****** = current title, D1 = Disk-1)

Rotating the JOG dial will toggle between “B01” and “Eject.”

If you wish to cancel the load operation and remove the disk, select “Eject” and press the EXECUTE/

YES key.

4. While “B01[******]D1 appears on the display, press the EXECUTE/YES key. (“SURE?” flashes).

The current Program number flashes and you can select the load destination Program.

P01[****** (****** = current title)

5. Use the JOG dial to select a Program into which to load data. (“SURE?” flashes.)

If you select a Program that already contains data and execute the load operation, that existing

data will be overwritten by the new data. If you do not wish to overwrite data in the Program, use

the JOG dial to select “New PGM” to execute the load operation.

6. Press the EXECUTE/YES key. (“REMAIN” and “LOAD” light up.)

Load operation will start, and the D-160 will display “B01>>P01 -***MB.”

This means that Backup 1 (B01) data in the SCSI disk is being loaded into Program 1 (P01) on the

internal hard disk. As the operation progresses, the number “-***MB” (remaining data amount to

be loaded) will count down. When loading from the first disk is complete, the message “Insert

Disk2” appears and the first disk is automatically ejected.

7. Insert the second disk into the SCSI device.

Loading from the second disk automatically starts. The display and count down are the same as

those for the first disk.

After all data is loaded, “COMPLETED!” lights up, and Time Base of the destination Program will

be located. Press the STOP button or the EXIT/NO key, and “COMPLETED!” will turn off.

<Notes>

* You cannot abort a load operation on a SCSI device while it is in progress.

* To enter a title for the SCSI disk, go to “2-20. Drive Sel.?” menu in the Setup mode

and change the current drive to “SCSI,” then go to “2-4. Title Edit?” menu in the

Setup mode to enter the title.

<Note>

If an error occurs during execution of load and "Error 36" appears in the display, carry out

the following steps:

1. Press the EXIT/NO key.

"Retry?" will appear in the display.

2^{. If load is to be executed again, press the EXECUTE/YES key upon display of "Retry?."}

Load will be executed again.

If ALL load was carried out in this process, load will be executed again from where the

error occurred. Also, if several disks are used for the load, it will load again from head of

the disk in which the error occurred.

3. If it is to be canceled without executing load, press the EXIT/NO key upon display of

"Retry?."

115

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (Saving and loading data)

4. Compatibility with D-90, D-80 V2.0, DMT-8 V2.0, and DMT-8

"FDMS-3 (Fostex Disk Management System-3)" for recording format of the D-160, and

"FDIO-1 Ver2.0 (Fostex Data In/Out-1 Ver2.0)" for save/load format of song data, are

employed. In the D-90, "FDMS-2 Ver2.0" and "FDIO-1 Ver2.0," in the D-80/D-80 Ver2.0

and DMT-8VL, "FDMS-2" and "FDIO-1", furthermore, in the DMT-8, "FDMS-1" and "FDIO-

1," respectively, are employed.

Due to these conditions, the hard disk recorded in the D-160 cannot be installed and

used in another equipment. However, as the save/load format is same for the D-160 and

D-90, data saved from the D-160 to an external digital equipment (adat or DAT) can be

loaded in 8 track units to the D-90 or data saved in the D-90 can be loaded in D-160.

Refer to list below for functional comparison of each product.

During save/load using DAT and Adat, independent save/load in 8 track units is possible.

In this case, the data in 8 track units are not distinguished as tracks 1~8 or 9~16 but simply

handled as eight track data.

Therefore, because this 8 track data is compatible with the D-90 if it is in 8 track units (any

one combination of 1~8, 9~16 or 17~24), data saved from the D-160 can be loaded in tracks

1~8 of the D-90.

In this case, data in the tracks which were not loaded will remain intact.

D-80 V2.0

D-160

D-90

DMT-8V2.0

DMT-8VL

5 (P1~P5)

DMT-8

Program

99 (P1~P99)

00: 00: 00: 00: 00

9 (P1~P9)

00: 00: 00: 00: 00

1 (P1)

00: 00: 00: 00: 00

Editing the memory data

23: 59: 59: 29: 59

06: 00: 00: 00: 00

Setting of the time base

Backup of the time memory

SETUP mode

Sampling frequency

44.1/48kHz

(64 points)

44.1/48kHz

(64 points)

44.1kHz

Setting of the time signature

Setting of the tempo

(64 points)

(16 points)

(32 points)

Metronome function

Loading/Saving

adat, S/P DIF, SCSI

(P1~P99)

adat, S/P DIF

(P1~P9)

S/P DIF

(P1~P5)

S/P DIF

(P1)

the song data

Setting of the preroll time

Setting of MIDI sync output signal

Setting of the MTC frame rate

00: 00: 00: 00: 00

Setting of the MTC offset time

23: 59: 59: 29: 59

06: 00: 00: 00: 00

Setting of the MTC offset mode

Setting of the Rec protect

Setting of the digital input track

Setting of the digital output track

Setting of the bar/beat

(adat, S/P DIF)

(S/P DIF)

resolution mode

Setting of the slave mode

Setting of the slave type

Setting of the MIDI device ID

Setting of the Undo function

116

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

MIDI sync function

The following are examples concerning general types of systems using MIDI

related functions contained in the D-160.

1. MIDI clock sync system

By setting any desired meter at any desired point of the programmable tempo map

contained in the D-160, and by output of a MIDI clock and song position pointer

according to the setting, a hardware type MIDI sequencer can be synchronized as a

MIDI clock slave. Consequently, in this system, the D-160 will be the master and

the MIDI sequencer the slave.

Unlike conventional tape type MTR, all sixteen tracks can be fully utilized without

wasting one track on a sync signal.

* Restore the default settings on D-160.

* Check for the correct program and proper sampling frequency.

D-160

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

MIDI OUT

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

MIDI Clock &

Song position

pointer

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

INPUT 1 - 8

OUTPUT 1 - 16

Master

INPUT L/R

Recorder

TAPE IN 1 - 16

BUSS OUT (GROUP OUT) 1 - 8

STEREO OUT L/R

MIDI IN

MIDI sequencer

MIDI OUT

INPUT

External Mixer

MIDI sound sources

MIDI IN

Connecting external equipment (Refer to connecting schematic)

1. Connect the D-160 MIDI OUT to MIDI IN of the MIDI sequencer.

2. Set the MIDI sequencer for "external sync mode (EXTERNAL SYNC) by MIDI clock."

* Refer to the Owners Manual of the equipment in use for details.

117

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Setup of D-160

1. Because the MIDI clock and song position pointer will be output from the D-160, set the SETUP

mode "MIDI sync signal output setting" to "CLK."

* Initial setting: CLK

* Permissible setting: CLK (MIDI clock and song position pointer:"CLK") / MTC (MIDI time code: "MTC")

/ Off (No output of MIDI sync signal)

* This item can be setup for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "150", SETUP mode "2-8. MIDI sync signal output setting" for correct

operating procedures.

2. The meter in the desired bar can be set by "Time signature setting" of the SETUP mode.

* Initial setting: 001 bar, 4/4 signature.

* Permissible bar setting: 001~999

* Permissible meter setting: 1/4, 2/4, 3/4, 4/4, 5/4, 1/8, 3/8, 5/8, 6/8, 7/8, 8/8, -- -- (Elimination of signature)

* Permissible setting of maximum number of points: 64 points

* This item can be set for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "143", SETUP mode "2-2. Time Signature Setting" for operating procedure.

3. Tempo in the desired bar can be set by "Tempo setting" of the SETUP mode.

Tempo map is made in steps 2 and 3.

* Initial setting: 001 bar, 1st meter, Tempo120.

* Permissible bar setting: Follows the previous "Setup of the time signature."

* Permissible signature setting: Follows the previous "Setup of the time signature."

* Permissible setting of tempo: Quarter note=30~250 .... (Tempo elimination)

* Permissible setting of maximum number of points: 64 points

* This item can be set for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "145", SETUP mode "2-3. Tempo Setting" for operating procedure.

4. Set the SETUP mode "Metronome setting" to ON if click sound is to be output according to the

setup tempo map.

* Initial setting: Off

* Permissible setup item: Off, On

* This item can be set for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "148", SETUP mode "2-6. Metronome setting" for operating procedure.

5. Press the DISP SEL key while pressing the EXECUTE/YES key, and then change the time base

display to BAR/BEAT/CLK.

Confirming the MIDI clock sync

During recording and at playback following the recording, the time base (BAR/

BEAT/CLK) is displayed in accordance to the setup tempo map, and the MIDI clock

and song position pointer is also output.

Confirm that the travel position (BAR/BEAT/CLK) of the D-160 and the travel

position of the synchronized MIDI sequencer are matched.

118

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

* If correct sync cannot be obtained, re-check the connections/cables and setting

of both equipment.

<Note>

In the D-160, the "ABS 0" position is set at "002BAR/1BEAT /00CLK."

This setting is made in consideration of the time required (it will not sync immediately)

for the MIDI sequencer, etc. to enter into sync.

As a result, if the D-160 is played back from ABS 0 (LOCATE ABS 0), sync will be

completed by the time it reaches the first bar, and will thus synchronize from head

of the tune.

Execution of recording

Various ways of recording can be conducted while synchronizing the D-160 and

the MIDI sequencer with the MIDI clock.

119

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

2. MTC sync/MIDI machine control system

The following will explain synchronization by the MTC (MIDI time code) output

and the computer controlling system using MMC (MIDI machine control). In this

system, the D-160 will be the master and the computer (with sequence software)

will be the slave.

The D-160 will attach any desired offset (time difference) against ABS time (absolute

time) and output it as MTC in any desired frame rate.

It can also carry out the proper operation upon receiving an MMC and Fostex

System Exclusive Message from outside. In this case, because the D-160 can setup

a DEVICE ID number by the SETUP mode "2-18. MIDI Device ID Setting" menu, a

multiple number of D-160's can be separately controlled by changing the DEVICE

ID numbers in the transmitted message from the computer.

In regards to the corresponding content for MMC, refer to the "MMC list" on page

"173" and on the Fostex System Exclusive Message, the "Fostex Exclusive List" on

page "174."

* Set D-160 in the initial state.

* Confirm the program and sampling frequency.

D-160

MIDI IN

AUTO RTN

MMC or Fostex System Exclusive Message

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

MIDI OUT

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

MTC

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

OUTPUT 1 - 16

INPUT 1 - 8

Master

INPUT L/R

Recorder

TAPE IN 1 - 16

BUSS OUT (GROUP OUT) 1 - 8

STEREO OUT L/R

MIDI IN

MIDI OUT

Computer System

with MMC/MTC

soft ware

INPUT

External Mixer

MIDI OUT

MIDI sound sources

MIDI IN

MIDI

120

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Connecting to external equipment

Connect the D-160 MIDI IN/OUT to the computer (with MIDI interface) MIDI IN/

OUT (MMC/MTC complied sequence software is activated in the computer).

Setup of external equipment

Setup the following in the sequence software.

* Set to MTC external sync mode (EXTERNAL SYNC).

* Set for output of MMC.

* Set to the desired MTC read out frame rate.

* Set start time of the tune (which MTC time is to be the first bar). Refer to precaution in regards to MTC

offset, farther on.

# For details, refer to Owners Manual of the external equipment.

Setup of D-160

1. Because MTC will be output from D-160, set to "MTC" the SETUP mode "MIDI sync signal

output setting."

# Refer to page "150", SETUP mode "2-8. MIDI sync signal output setting" for operating

procedure.

2. Set a random offset time by the SETUP mode "MTC offset time setting."

* Initial setting: 00h (Hour) 59m (Minute) 57s (Second) 00f (Frame) 00sf (Sub Frame)

* Permissible setup time: 00h 00m 00s 00f 00sf ~ 23h 59m 59s 29f 99sf

* This item can be set for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "152", SETUP mode "2-10. MTC offset time setting" for operating

procedure.

3. In the SETUP mode "MTC offset mode setting," whether the MTC offset time setup in Step 2

should be output (ABS) at the ABS 00m 00s 00f 00sf position or at the 001BAR 1BEAT 00CLK

(bar, signature) must be selected.

* Initial setting: ABS

* Permissible setup item: ABS, Bar

* This item can be setup for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "153", SETUP mode "2-11. MTC offset mode setting" for operating

procedure.

4. Setup to the same frame rate as that setup by the sequence software by "MTC Frame rate

setting" of the SETUP mode.

* Initial setting: 25 frames

* Permissible setup of frame rate: 24, 25, 29nd, 29df, 30nd, 30df

* This item can be setup for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "151", SETUP mode "2-9. MTC Frame rate setting" for operating

procedure and details.

5. Set to the same figure as the sequence software MMC device number (and Fostex System

Exclusive Message device number) by the SETUP mode "MIDI device ID setting."

When the sequence software transmits by "7F," it means "ALL DEVICE" and therefore, it

need not be setup. The D-160 transmitting device ID will also function in parallel with this

setting.

121

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

* Initial setting: 00

* Permissible setup ID: 00 ~ 99

* This item will be the setting common to all programs.

* This setting cannot be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "161", SETUP mode "2-18. MIDI device ID setting" for operating

procedure and details.

6. Press the DISP SEL key while pressing the EXECUTE/YES key to show time base in the MTC

display.

By "MTC offset time setting" and "MTC offset mode setting," at what position (ABS 0 or 001BAR/

1BEAT/00CLK) should the setup MTC (MTC offset time) is to be output is set. When setting the

start time of the tune in the sequence software by these setups, be careful of the following points.

* Offset mode: For ABS

If playback is started from ABS 0, since MTC will be output starting from the MTC offset time that

has been set, the start time of the tune set by the sequence software must be set about 3 seconds

later from the MTC offset time that was setup. This will provide time because the sequence

software cannot sync immediately after MTC is output. For example, if the initial setting of 00h

59m 57s 00f 00sf" is used, set the start time of the tune to "01h 00m 00s 00f." If playback is thus

started from ABS 0 (LOCATE ABS 0), sync will be obtained by the time it reaches the first bar and

therefore it can be made to sync from the head of the tune.

* Offset mode: For BAR

As mentioned before, because the "ABS 0" position is set at the "002BAR / 1BEAT / 00CLK" position,

the setup MTC offset time can be set to the head of the tune without taking into account the time

until reaching sync, as mentioned above. The length of the time two bars beforehand will change

in accordance to the first bar setting for "signature" and "tempo." For example, it will be long if

the tempo is set slow. This mode can be effectively applied when using the MIDI clock and MTC in

parallel, and when using MTC for the sync signal while controlling the D-160 with time base BAR/

BEAT/CLK.

Confirming MTC sync/MMC

1. During recording and at playback after recording, time base MTC is displayed according to the

setting and MTC is output at the same time.

Check that the D-160 traveling position (MTC) and the traveling position of the sequence

software in sync are matched.

2. Send MMC commands such as PLAY, STOP and LOCATE from the sequence software to see

that the D-160 will be properly controlled.

When a correct MIDI command (MMC or FEX) is received, "MIDI" in the display will be lit

for about 40msec. There is no setting in the D-160 to receive MMC or FEX but it will

operate if a correct MIDI signal is input.

* If sync and control cannot be done correctly, re-check connections/cables and

the setting of both equipment.

Execution of recording

Carry out various recordings while synchronizing a D-160 and a MIDI sequencer

with the MIDI clock.

122

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

3. Multitrack system by the slave mode

The following will explain an example of constructing a 48 track system using

three D-160's and its slave mode functions.

* Initialize D-160.

* Confirm the program.

* Set all three D-160's to the same sampling frequency.

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

COPY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

MOVE

PASTE

REDO

STORE

RECALL

D-160 (#1)

(Master)

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

MIDI OUT

DATA OUT

DATA IN

MIDI IN

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

OUT

START

OUT

END

DISP SEL

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

HOLD/

STORE

RECALL

POWER

D-160 (#2)

(Slave 1)

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

DATA OUT

DATA IN

DIGITAL MULTITRACK RECORDER

MIDI THRU

MIDI IN

AUTO RTN

AUTO PLAY

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

D-160

OUT

START

END

DISP SEL

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

HOLD/

STORE

RECALL

D-160 (#3)

(Slave 2)

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

Equipment interconnections

1. From D-160 (#1) to D-160 (#2), connect DATA OUT to DATA IN and MIDI OUT to MIDI IN.

2. From D-160 (#2) to D-160 (#3), connect DATA OUT to DATA IN and MIDI THRU (Note!!!) to MIDI

IN.

<Note>

In order to slave drive a D-160 with each other, the best setting is to supply Adat digital

signals together with MTC from the master.

Setup of D-160 (#1)

1. Because MTC, which is the reference for sync, is output from D-160 (#1), set the "MIDI sync

signal output setting" of the SETUP mode to "MTC."

# Refer to page "150", SETUP mode "2-8. MIDI sync signal output setting" for operating

procedure and details.

2. A random frame rate to be used is set by the SETUP mode "MTC Frame rate setting."

# Refer to page "151", SETUP mode "2-9. MTC Frame rate setting" for operating

procedure and details.

3. With the SETUP mode "MTC offset mode setting," whether the MTC offset time will be output

(ABS) at the ABS 00h 00s 00f 00sf point or at the 001BAR 1BEAT 00CLK (bar/signature) point

of the tempo map, is selected.

# Refer to page "153", SETUP mode "2-11. MTC offset mode setting" for operating

procedure and details.

123

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

4. A random offset time is set by the SETUP mode "MTC offset time setting."

# Refer to page "152", SETUP mode "2-10. MTC offset time setting" for operating

procedure and details.

5. "00" is set with the SETUP mode "MIDI device ID setting."

# Refer to page "161", SETUP mode "2-18. MIDI device ID setting" for operating

procedure and details.

6. Set to "adat" the digital signal to be output by the SETUP mode "Digital output track setting."

# Refer to page "159", SETUP mode "2-16. Digital output track setting" for operating

procedure and details.

7. Press the DISP SEL key while pressing the EXECUTE/YES key to change the time base display

to MTC.

Setup of D-160 (#2) (Slave 1) and D-160 (#3) (Slave 2)

1. Set the SETUP mode "MTC Frame rate setting" to the same frame rate as in D-160 (#1).

* Refer to page "151", SETUP mode "2-9. MTC Frame rate setting" for operating

procedure and details.

2. Set the SETUP mode "MTC offset mode setting" to the same mode as in D-160 (#1).

# Refer to page "153", SETUP mode "2-11. MTC offset mode setting" for operating

procedure and details.

3. Set the SETUP mode "MTC offset time setting" to the same offset time as in D-160 (#1).

# Refer to page "152", SETUP mode "2-10. MTC offset time setting" for operating

procedure and details.

4. Set the SETUP mode "MIDI device ID setting," to "01" in D-160 (#2), and to "02" in D-160 (#3).

# Refer to page "161", SETUP mode "2-18. MIDI device ID setting" for operating

procedure and details.

5. Using the SETUP mode "Slave mode setting," set slave mode to "On," and the SETUP mode

"Slave mode type setting," the slave type to "adat."

* Slave mode initial setting: Off

* Permissible setup item: On, Off

* Slave type initial setting: SP DIF

* Permissible setup item: Vari, SP DIF, adat, Free

* This item can be set for each program.

* The setting can be saved/loaded as song data.

* This setting will be held even though power is switched OFF.

# Refer to page "154", SETUP mode "2-12. Slave mode setting" , and to page "155",

SETUP mode "2-13. Save mode type setting", for operating procedure and details.

6. Press the DISP SEL key while pressing the EXECUTE/YES key to change the time base display

to MTC.

<Note>

After this setup, check the following in D-160 (#2) and D-160 (#3).

* Blinking of "CHASE" in the display:

This will change to constant lit upon completing chase lock in later operation.

* "DIGITAL" is lit in the display:

This means it is externally synchronized against the input digital signal.

<Note>

Do not insert or remove the optical cable connected to DATA IN when the slave mode is

set to "On." Doing so could generate noise and affect external equipment.

124

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Check chase lock

1. When the master unit (D-160 (#1)) is played back, MTC IN LED of the slave unit (D-160 (#2) and D-

160 (#3)) will be lit, "CHASE" in the display will immediately change from blinking to lit and chase

lock will be completed.

Check that the MTC time on display are same in both master and slave units.

2. When the master starts recording, the slave will also start recording upon completing chase

lock.

3. When the master is stopped, the slave will also stop as MTC from the master will be interrupted.

"CHASE" in the display will change from lit to blinking.

4. During FF/REW, the master only will be in the FF/REW mode and the slaves will remain

stopped but when playback/recording is started, the slaves will immediately chase lock.

<Note>

The D-160 re-chase window is fixed at "10 frame." In other words, when MTC of the

master and slave drifts apart more than 10 frames, it will assume that chase lock is

disengaged and the slave will match the position again with the master (re-chase

operation). During the re-chase operation, sound output will be muted. If the drift is

within 10 frames, the slave will recognize this and continue to travel.

Because the master supplies digital signal to slave in this system, re-chase is rarely

carried out following chase lock.

* Should the D-160 fail to correctly chase lock and control, re-check the connection

/cables and all settings.

Selecting a recording track

Select the recording tracks for both master and slave.

Execution of recording

A variety of recording work can be carried out with all three D-160's in the chase

lock mode.

125

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

1. Setting the “Digital input/output track” parameter in the Setup mode allows you to input and output a

digital signal. Note the following when you set this parameter.

* When you set up a digital input track and “DIGITAL (red)” lights up on the display, the D-160 is ready for

syncing with an external word clock via the input digital signal. Use caution not to make a digital signal loop

as mentioned previously.

* When you set up a digital input track, the settings for the external sync signal of the “Slave mode setting” in

the Setup mode (that is, Vari, SP DIF, adat, and Free) will be ignored, and the D-160 will sync with the

specified digital input signal. Refer to “2-13. Slave Type setting” in Setup mode on page "155" for more

information.

* When you set up a digital input track, the Vari-pitch function is turned off (the LED is also turned off).

2. You can integrate the “MIDI clock sync” operation or “MTC sync/MMC system” operation (as mentioned

before) into this multitrack system.

MMC/FEX

MIDI IN

MIDI OUT

D-160 (#1)

DATA OUT

MIDI OUT

MIDI IN

DATA IN

D-160 (#2)

DATA OUT

MIDI THRU

MIDI IN

COMPUTER

with MMC/MTC

software

DATA IN

D-160 (#3)

MIDI IN

MIDI OUT

Connection:

MIDI OUT of D-160 (#3) is connected to MIDI IN of the external MIDI equipment.

Setup of the MIDI sync signal:

In D-160 (#3), select either the MIDI clock necessary for synchronizing or MTC.

* For MIDI clock sync, the external MIDI equipment and D-160 (#3) must be setup by the previously

discussed "MIDI clock sync" procedure.

* For MTC sync, the external MIDI equipment and D-160 (#3) must be setup by the previously discussed

"MTC sync/MMC system" procedure.

* Control of each D-160 becomes possible if the DEVICE ID in the sequence software MMC output (3 channels)

is set to comply with the DEVICE ID (00, 01, 02) setup in D-160.

* When in any mode other than output of MIDI CLOCK from the D-160, MMC from MIDI IN and also FEX are

automatically merged and output from MIDI OUT.

In the above schematic, the MMC and the reply message of MMC/FEX which are output from D-160

(master) itself and, MMC and FEX output from the computer, are merged and output from MIDI OUT.

126

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

4. External MIDI equipment sync system by the slave mode

Up to this point, synchronization with external MIDI equipment has been explained with

the D-160 as the master and MIDI equipment as the slave but depending on the slave

mode setting, the MIDI equipment can be set as the master and D-160 as the slave.

<Note>

External MIDI equipment which can be used as the master is limited to those which

can output MTC.

* Initialize D-160.

* Confirm the program and sampling frequency.

* In the following, the explanation will be on the assumption that a computer (with sequence

software) is used.

Computer

with MMC/MTC

soft ware (Master)

MIDI OUT

D-160 (Slave)

MIDI IN

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

Connection to external equipment

Connect MIDI OUT of the computer (with MIDI interface) with MIDI IN of D-160.

The computer sequence software complying to MMC/MTC must be activated.

Setup of external equipment

Sequence software is setup as follows.

* Set for output of MTC.

* Set frame rate of the MTC to be output.

* Confirm start time of the tune.

# Refer to Owners Manual of the respective equipment for details.

Setup of D-160

1. Set to same frame rate as the sequence software by the SETUP mode "MTC Frame rate setting."

# Refer to page "151", SETUP mode "2-9. MTC Frame rate setting" for operating

procedure and details.

2. Set to the desired mode by the SETUP mode "MTC offset mode setting."

# Refer to page "153", SETUP mode "2-11. MTC offset mode setting" for operating

procedure and details.

3. A random offset time can be set by the SETUP mode "MTC offset time setting."

127

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

# Refer to page "152", SETUP mode "2-10. MTC offset time setting" for operating

procedure and details.

4. Set slave mode to "On" by the SETUP mode "Slave mode setting," and the slave type to "Vari"

by the SETUP mode "Slave mode type setting."

# Refer to page "154", SETUP mode "2-12. Slave mode setting" , and page "155",

SETUP mode "2-13. Slave mode type setting", for operating procedure and details.

5. Press the DISP SEL key while pressing on the EXECUTE/YES key to change the time base

display to MTC.

The position (ABS 0 or 001BAR/1BEAT/00CLK) when the setup MTC (MTC offset

time) should be output was setup by the "MTC offset time setting" and "MTC offset

mode setting." In accordance to start time of the tune set by the sequence software,

setup as explained below.

Offset mode: For ABS

Set the MTC offset time about three seconds prior to the start time of the tune set by

the sequence software. Because the D-160 cannot immediately chase lock after input

of MTC, in order to sync the D-160 from head of the tune, set the preroll using the

sequence software, and playback from before the actual head of the tune to allow the

D-160 to enter into sync by the time it arrives at the head of the tune.

Offset mode: For BAR/BEAT

The MTC offset time can be set to the same time as the start time of the tune set by

the sequence software. Because the "ABS 0" position is set at the "0002BAR/1BEAT/

00CLK" position in the D-160, as mentioned before, the preceding time required for

sync is already set. The preceding time of two bar lengths could change in length

depending on the first bar's "signature setting" and "tempo setting" mentioned before.

For example, it will be longer if the tempo is slowed down.

Confirming chase lock

1. When the sequence software is played, MTC IN LED of the D-160 will light, "CHASE" in the

display will change from blinking to lit and the chase lock will be completed.

Check that the MTC output by the sequence software and MTC time displayed in the D-160

are the same.

2. When the sequence software stops, MTC will be interrupted and the D-160 will also stop.

"CHASE" in the display will change from lit to blinking.

3. During FF/REW of the sequence software, D-160 will remain stopped but upon starting to record,

the D-160 will immediately chase lock.

<Note>

Chase lock of the D-160 by MTC only is permissible when speed difference of the MTC

from the master is within +/- 5.6%. Against the MTC within this range, variable pitch

will be constantly applied internally for chasing. Chase lock, however, will not function

against MTC at a speed difference outside this range.

Also, when the master speed difference is large, it is advised to let D-160 learn the

master speed by entering PLAY prior to recording. By doing so, it will be lock faster

from the second and later sessions.

* Should it not be possible to chase lock, re-check connections / cables and all

settings.

128

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Execution of recording

Carry out various recordings while the D-160 is chase locked to the sequence

software.

Sync signal "Free" of the "Slave mode setting" menu:

When the D-160 is made to chase lock by MTC only, variable pitch will be constantly

applied by external MTC. If a digital signal is output to an external digital equipment

from the D-160, it will not be able to follow the speed difference (MTC speed difference

of the master) of the D-160 and the external digital equipment, in some cases, may

not be able to input a continuous digital signal.

As a counter measure, the sync signal should be set to "Free" by the "Slave mode

setting" menu. Using this setting, the D-160 will enter self operation by the internal

clock, after completion of chase lock, and it will be possible to supply a stable digital

signal to the external equipment.

Under this setting, when MTC drift between the master unit and slave unit exceeds 10

frames, the D-160 will assume that chase lock has been disengaged and the slave unit

will carry out position matching again with the master unit (re-chase operation).

During the re-chase operation, sound output will be muted and the digital signal will

also be interrupted. If it is within 10 frames, the slave unit will continue to run while

admitting this drift.

<Note>

When you select “Vari” for the Slave mode setting, the D-160 will use the Vari-pitch

function to lock to the MTC coming from the master device.

However, if you select an S/P DIF digital signal or an adat digital signal for the digital

input track in Setup mode, the D-160 will sync with the word clock via the input

signal.

Therefore, when you set up a digital input track, the D-160 will not sync with the MTC

even if “Vari” has been selected for the Slave mode setting. Once the D-160 locks to

the master device, it will sync to the external digital input signal (in the same manner

as when SP DIF or adat signals are used).

129

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

5. Sync system with "adat" by the slave mode

This section will explain the sync system using "adat" equipment such as the Fostex

RD-8.

* Initialize D-160.

* Confirm the program.

* Set RD-8 and D-160 to the same sampling frequency.

RD-8 (Master)

MIDI OUT

DIGITAL OUT

DATA INPUT

D-160 (Slave)

MIDI IN

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

Equipment connections

Make connections, respectively, RD-8 DIGITAL OUT to D-160 DATA IN, and RD-8

MIDI OUT to D-160 MIDI IN.

<Note>

In order to slave operate adat equipment and the D-160, the best setting is to supply

"adat" digital signals together with MTC from the master unit.

Setup of RD-8 (master)

1. Setup for output of MTC.

2. Setup the MTC frame rate to be output.

3. Check the MTC time to be output.

4. If necessary, set to allow output of "adat" digital signals.

This is unnecessary for the RD-8.

# Refer to the RD-8 Owners Manual for details.

Settings on the D-160

1. Set the same frame rate as the RD-8 for the “MTC Frame rate setting” in the Setup mode.

# Refer to “2-9. MTC Frame rate setting” in Setup mode on page "151" for the operation and

more information.

2. Select a desired mode for “MTC offset mode setting” in the SETUP mode. (*)

# Refer to “2-11. MTC offset mode setting” in Setup mode on page "153" for the operation

and more information.

130

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

3. “MTC offset time setting” in Setup mode allows you to set the MTC time to start the Chase Lock

operation. (*)

# Refer to “2-10. MTC offset time setting” in Setup mode on page "152" for the

operation and more information.

4. Set Slave mode "On" for “Slave mode setting” in Setup mode, and select “adat” as a slave mode

type for “Slave mode type setting” in Setup mode.

# Refer to “2-12. Slave mode setting” in Setup mode on page "154", and "2-13. Slave mode

type setting" in Setup mode on page "155", for the procedure and information.

5. Press the DISP SEL key while holding down the EXECUTE/YES key to select the MTC indication

for the Time Base.

“MTC offset time setting” and “MTC offset mode setting” determine at which point

(ABS 0 or 001BAR/1

/00CLK) the MTC (MTC offset time) is output. Refer to the

following, depending on the song start time set in your sequence software, to set the

MTC output from the RD-8.

* Offset mode: ABS

When the master device (RD-8) outputs the specified MTC (MTC offset time), the slave

D-160 will start the Chase-Lock operation. Remember that it will take a little time for

the D-160 to start chase-lock after the MTC is input. Setting the MTC offset time will

allow the Chase-lock operation to start from the specified point of the master device.

For example, when the master device (RD-8) outputs MTC as 00h 00m 00s 00sf ~ 00h

40m 00s 00sf, if the D-160 offset (ABS mode) is 00h 20m 00s 00sf, the D-160 ABS time

will lock from 23h 40m 00s 00sf, and if the frame rate setting is 30 frame, lock will

disengage temporarily at 23h 29m 59s 29f.

Later on, it will lock again at ABS time in the vicinity of 00h 00m 03s.

This is an indication that the ABS time 24h is set as access maximum time in the D-160

and that return to "0" is not continuous.

Should no overshooting of 24h occur in the ABS time, overshooting of 24h with a

random MTC OFFSET can be carried out correctly.

* Offset mode: BAR

As described previously, the D-160 uses “-002BAR/1 /00CLK” as an “ABS 0” point,

there is enough time until the Chase Lock starts, and Chase Lock will be complete by

the specified MTC offset time. The time length of the two bars before the Chase Lock

will vary depending on the settings in the first bar for the “Time signature setting”

and the “Tempo setting.” Setting the MTC offset time will also allow the Chase Lock

operation to start from the specified point of the master device.

<Note>

After this setting, check the following items on the D-160:

* “CHASE” is flashing on the display: When the Chase Lock operation is complete,

this indicator will light.

* “DIGITAL” lights up on the display: The unit is syncing to the external digital signal.

<Note>

Do not connect or remove the optical cable from the DATA IN connector while Slave

mode is on. Otherwise, the unit may generate noise, affecting the connected external

devices.

131

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Checking Chase Lock

1. When the master device (RD-8) is played, the MTC IN LED on the slave machine (D-160) will light,

then “CHASE” will light in the display, and Chase Lock will be complete.

Check to make sure the display shows the correct MTC time.

2. When you stop the master device, the MTC transmission from the master device will be interrupted

and the slave machine will also stop.

The illuminated “CHASE” will flash.

3. While the master device is in fast forward or rewind mode, the slave machine will remain stopped.

When you start playing the master device, the slave machine will start the Chase Lock

operation.

<Note>

The D-160’s re-chase window is “10 frames” fixed. That is, when the MTC of the master

device and the MTC of the slave machine slip from each other by 10 frames or more, the

slave machine will interpret this as being out of sync, and it will try to lock with the master

device again (this is called a “re-chase” operation). During the re-chase operation, audio

output will be muted. If slippage is within 10 frames, the slave machine will continue running

while accepting the slippage. Since the master device supplies a digital signal to the slave

machine in this system, the slave machine will not perform the re-chase operation after

chase lock is complete.

* If the Chase Lock operation or control is not correct, check all connections, cables, and

settings.

Recording

You may perform recording while the RD-8 and the D-160 are chase-locked.

* Setting the “Digital input track setting” and “Digital output track setting” on the

D-160 will allow audio to be transferred between devices in the digital domain.

Please note that a track specified for digital input will not accept an analog signal.

When this system is to be used with the digital input track set to "adat," because

an analog can be input to the adat track not connected, a digital 8 track and

analog 8 track can be simultaneously recorded.

For example, if DATA INPUT 1-8 are being used and DATA INPUT 9-16 are not

connected, analog signals can be input in the analog input 9-16 connectors.

132

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

6. Multitrack system using a D-90 / D-80 (Ver. 2) / DMT-8 (Ver.2/VL)

This section explains a multitrack system that uses the D-160 as master and a D-90, D-80,

D-80Ver. 2, DMT-8 Ver. 2, or DMT-8VL as slave. Using the D-160 as a master device

allows for Chase Lock operation using the Vari-pitch function or the MTC.

The example explained here uses Fostex DMT-8 Ver. 2 as a slave machine, but you can

use another model with the same settings to configure the multitrack system.

<Note>

A DMT-8, which does not have a Slave Sync function, cannot be used in this system.

However, it can be used as a master device. Refer to the “Hint” described later.

<Note>

Note the following when you use the D-160 along with a D-90, D-80, D-80 Ver. 2, DMT-8 Ver.

2, DMT-8VL, or DMT-8.

1. Use only Programs P1 - P5.

2. Select 44.1kHz for the sampling frequency.

3. Select S/P DIF for the digital signal. An adat digital signal can be used only on the D-90.

* Initialize the D-160 and the DMT-8 Ver. 2.

* Check the Programs on both machines (P1-P5).

* Set the sampling frequency on both machines to 44.1kHz.

Connecting the devices

* Connect DATA OUT of the D-160 to DATA IN of the DMT-8 Ver. 2, and MIDI OUT of the

D-160 to MIDI IN of the DMT-8 Ver. 2.

<Note>

The best setup is to supply the MTC and S/P DIF digital signal from the master device so

slave operation will be successful.

D-160 (Master)

AUTO RTN

CLIPBOARD

AUTO PUNCH

IN OUT

EXECUTE

/YES

EXIT

/NO

DIGITAL MULTITRACK RECORDER

D-160

AUTO PLAY

OUT

START

END

DISP SEL

HOLD/

AUTO RTN

ERASE UNDO

TIME BASE SEL

COPY

MOVE

PASTE

REDO

STORE

RECALL

POWER

PGM CHANGE

AUTO

PUNCH

REHEARSAL

TAKE

LOCATE

VARI PITCH

RECORD

STOP

PLAY

REWIND

FWD

RECORD TRACK

1/9

2/10

3/11

4/12

5/13

6/14

7/15

8/16

SHIFT

PUNCH

IN OUT

LOCKED

HD ACCESS

MTC IN

CLIPBOARD PLAY

LOCATE ABS

LOCATE ABS END

DATA OUTPUT 1-8

MIDI OUT

MIDI IN

DATA IN

DMT-8 ver.2(Slave)

133

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Procedure for the Chase Lock operation

1. Press a RECORD TRACK select key on both machines to set the tracks in the “READY” mode.

2. Press the RECORD and PLAY buttons on the D-160 to start recording.

The DMT-8 Ver. 2 will also start recording. This is because the master device will send

a RECORD command.

This procedure is used to create an area that can be played back on the DMT-8 Ver. 2;

you do not need to input audio (silence recording). If you make a silent recording of

almost the same length as the song to be recorded, sync operation can be started at

any point in the song.

3. Press the STOP button on both machines.

* If something has been previously recorded, you do not need to perform this procedure.

<Note>

The D-90, D-80, D-80 Ver. 2, DMT-8 Ver. 2, DMT-8VL, and DMT-8 can play back only

the recorded area (ABS 0 through ABS END).

Therefore, if nothing is recorded, they cannot output the MTC or perform the Chase Lock

(sync).

At this point the devices are not chase-locked, but recording separately.

Follow the procedure below so that the two units will chase-lock to each other.

Setting the D-160 (Master)

1. The D-160 will output the MTC for the sync operation.

Set the “MIDI sync output signal setting” in the Setup mode to “MTC.”

# Refer to “2-8. MIDI sync output signal setting” in the Setup mode on page "150" for the

procedure and additional information.

2. Set any frame rate for the “MTC Frame rate setting” in the Setup mode.

# Refer to “2-9. MTC Frame rate setting” in the Setup mode on page "151" for the procedure

and additional information.

3. Select “ABS” for the sake of compatibility with the DMT-8 Ver. 2 for “MTC offset mode setting”

in the Setup mode.

# Refer to “2-11. MTC offset mode setting” in the Setup mode on page "153" for the

procedure and additional information.

4. Set an offset time for “MTC offset time setting” in the Setup mode.

# Refer to “2-10. MTC offset time setting” in the Setup mode on page "152" for the procedure

and additional information.

5. Set the “MIDI device ID setting” in the Setup mode to “00”.

# Refer to “2-18. MIDI device ID setting” in the Setup mode on page "161" for the procedure

and additional information.

6. Select “SP DIF” as the digital output signal for the “Digital output track setting” in the Setup

mode.

* Only an S/P DIF digital signal can be used with the D-80, D-80 Ver. 2, DMT-8 Ver. 2,

DMT-8 VL, and DMT-8.

# Refer to “2-16. Digital output track setting” in the Setup mode on page "159" for the

procedure and additional information.

7. Press the DISP SEL key while holding down the EXECUTE/YES key to select MTC as the Time

Base indication.

134

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Setting the DMT-8 Ver. 2 (Slave)

# Refer to the DMT-8 User’s Guide for the procedure and additional information.

1. Use the same frame rate as the D-160 for the “MTC frame rate setting” in the Setup mode.

2. Use the D-160’s offset time for the “MTC offset time setting” in the Setup mode.

There is no “MTC offset mode setting” on the D-80, D-80 Ver. 2, DMT-8 Ver. 2, and

DMT-8 VL. When you use the D-160’s setting, the MTC offset mode will automatically

become “ABS.”

3. Set the “MIDI device ID setting” in Setup mode to “01” on the DMT-8 Ver. 2.

4. Set the Slave mode to “On” for the “Slave mode setting” in the Setup mode.

You can set the Slave mode on the D-80, D-80 Ver. 2, DMT-8 Ver. 2, and DMT-8 VL, but

you cannot select a sync signal (SLAVE TYPE). If you use the D-160’s setting, “SP DIF”

will be automatically selected.

5. Press the DISP SEL key while holding down the EXECUTE/YES key to select MTC as the Time

Base indication.

<Note>

After this setting, check the following items on the DMT-8 Ver. 2:

* “LOCKED” LED is flashing: When the Chase Lock operation is complete, this indicator

will light.

* “DIGITAL” lights on the display: The unit is syncing to the external digital signal.

<Note>

Do not connect or remove the optical cable the DATA IN connector while

Slave mode is on. This can generate noise, affecting the connected external devices.

Checking Chase Lock

1. When the master device (D-160) is played, the flashing “PLAY” button lamp will light and

Chase Lock will be complete.

Check to make sure the display shows the correct MTC time.

2. When you start recording on the master device, the slave device will start recording after the

Chase Lock operation is complete.

3. When you stop the master device, the MTC transmission from the master device will be interrupted

and the slave machine will also stop.

The illuminated “PLAY” button's lamp will begin to flash.

4. While the master device is in fast forward or rewind mode, the slave machine will remain stopped.

When you start playing or recording on the master device, the slave machine will start

the Chase Lock operation.

<Note>

The re-chase window of the D-90, D-80, D-80 Ver. 2, DMT-8 Ver. 2, and DMT-8 VL is “10

frames” fixed. This is the same as the D-160. When the MTC of the master device and

the MTC of the slave machine slip from each other by 10 frames or more, the slave

machine will interpret this as being out of sync, and will try to lock with the master

device again (this is called a “re-chase” operation). During the re-chase operation,

audio output will be muted. If slippage is within 10 frames, the slave machine will

continue running while accepting the slippage. Since the master device supplies a digital

signal to the slave machine in this system, the slave machine will not perform the re-

chase operation after chase lock is complete.

* If the Chase Lock operation or control is incorrect, check all connections, cables, and

settings.

135

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MIDI sync function)

Selecting a recording track

Select the recording tracks for both master and slave.

Recording

You can record while the D-160 is chase locked.

You can use the D-160 as a slave machine. In this case, set the Slave mode to “On”

for the D-160’s “Slave mode setting”, and set Slave type to “SP DIF” for "Slave mode

type setting."

In this system, on the D-160 you can use only those functions available on the

D-80, D-80 Ver. 2, DMT-8 Ver. 2, DMT-8 VL, and DMT-8.

Therefore, you cannot use the Vari-pitch function.

136

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

SETUP mode

The setup mode allows you to set up parameters for the D-160 according to your

requirements.

The contents that you can set up are listed below.

There are two types of setup modes. Some modes are commonly applicable to all

programs from 1 to 99 and some others are applicable to each program individually,

except for Load, Save & Format.

You can save or load those set up modes, which are applicable program by program as a

part of the song data, as we described before in the "SAVING/LOADING SONG DATA"

section. But, those which are applicable to all programs are not saved or loaded.

Nevertheless, they are memorized even if you turn off the power.

Mode

Functions

Community

Initial Setting

Trk=01 <-> Trk=01

001 bar 04 04 (4/4 beat)

001 bar 1 =120 (Tempo 120)

"Track Exchange?"

"Signature Set?"

"Tempo Map Set?"

"Title Edit?"

Track Swapping

Time Signature Setting (Chosen from 11 setting from 1/4

Tempo Setting (30Å`250 bpm)

Program Name Setting (Up to 16 digits)

Program Deleting

8/8)

#0001

"Delete PGM?"

"Click ?"

Metronome ON/OFF Setting

Off

"Preroll Time?"

"Midi Sync Out?"

"Frame Rate?"

"MTC OFFSET"

"MTC Offset Mode?"

"Slave Mode?"

"Ref.TC?"

Preroll Time Setting for LOCATE Function

Midi Sync Out Signal Setting

00s (00 second)

CLK (MIDI Clock)

25 Frames

MTC Frame Rate Setting

Offset Time Setting between ABS and MTC

MTC Offset Mode Setting

0h 59m 57s 00f 00sf

ABS

Slave Mode ON/OFF Setting

Off

Available with Option Model 8345 (Refer to the Model 8345 Owners Manual)

Slave Mode Type Setting

"Slave Type?"

"Rec Protect?"

"Digi. in?"

Vari

Record Protect ON/OFF Setting

Off (Record Enable)

Digital Input Track Setting

L--, R-- (Nothing is assigned)

"Digi. out?"

Digital Output Track Setting

Adat

Resolution?"

Bar/Beat Resolution ON/OFF Setting

Off

"Device ID?"

MIDI Device ID Setting

00 (Device No. =00)

44.1kHz

"Sample Rate?"

"8345 Clock?"

"Word Out?"

Sampling Frequency Setting

Available with Option Model 8345 (Refer to the Model 8345 Owners Manual)

"Sync Preset?"

"NOs Of Event?"

"Drive Sel.?"

Event Number Check of a Track

Current Drive Setting

IDE (Internal Hard disk)

"Load PGM?"

"Save PGM?"

"Disk Format?"

Loading Song Data from External Device

Saving Song Data to External Device

Initializing Internal Hard disk/SCSI disk

: Modes applicable program by program. They can be saved/loaded.

: Modes applicable to all programs. They cannot be saved/loaded.

The " " means a quarter note(1/4 note) through out this manual.

1. How to enter the Setup Mode

This is the procedure to arriving at the stage for choosing the other modes you

require. The procedure from now on is written assuming the required program

has already been selected. So, make sure the program you want to work on is

already selected.

1. Press the Display key and choose the flashing SETUP mode on the display.

SETUP

44.1kHz

∞

2. Press the EXECUTE/YES key.

The SETUP display stops flashing.

This is the first step in the set up mode.

137

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

SETUP

44.1kHz

∞

<Note>

The setup menu will show the "Track Exchange?" mode as for the factory default setting

or just after you have formatted the internal hard disk drive. However, except for these,

the setup menu will show the last mode you chose.

3. Turn the JOG dial and choose the mode you want.

If you rotate the JOG dial either clockwise or counter clockwise, the modes appear one after the

other. Some modes also show their current settings.

When you turn the JOG dial, SETUP menus will be displayed in the following order.

As you change the menu, the position indicators in the FL tube display will also start flashing

and moving on one after another.

"Track Exchange?"

The position of the SETUP menu that you choose will

"Signature Set?"

start flashing on the level meters. Each SETUP menu

Tempo Map Set?"

has a dedicated position in the FL tube display.

When you change the menu with the JOG dial, the

position indicators start flashing one after another.

Use this feature as a reference to choose the SETUP

"TitleEdit PGM**?" (PGM01)

"Delete PGM**?"(PGM01)

"Click ?"(Off)

menus.

"Drive Sel. ?"

"PrerollTime?"(00s)

"Track Exchange ?"

"MidiSyncOut?" (CLK)

"Frame Rate?" (25 frame)

"MTC OFFSET" (00h 59m 57s 00f 00sf)

"Offset Mode?" (ABS)

"Slave Mode?"(Off)

"Ref. TC?" (Void!)

"SlaveType?" (Vari)

"Rec Protect?" (Off)

"Rec Protect ?"

"MTC OFFSET"

"Digi. in?" (L--, R--)

"Digi. out?"(adat)

Resolution?" (Off)

"Device ID?" (00)

This feature also shows these four menus; "Ref.TC?",

"8345 Clock", "Word Out" and "Sync Preset". However,

since these menus will only work when the optional

accessory Model 8345 is installed, there is no

explanation of these functions in manual.

"SampleRate?" (44.1)

"8345Clock" (Void!)

"Word Out"(Void!)

"SyncPreset"(Void!)

"NOs Of Event"

Refer to the Model 8345 owners' manual for details.

"Drive Sel. ?"(IDE)

"Load PGM?"

"Save PGM?"

"Disk Format?"

138

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

4. Press the EXECUTE/YES key. The mode you wanted has been chosen.

This is the second step in the SETUP mode.

Refer to the pages below for details of each SETUP mode. For your information, the actual

display will appear as follows. (the

means flashing display) :

SETUP

44.1kHz

"Track Exchange?" -> Track Swapping

(Initial setting : Trk=01<->Trk=01)

∞

SETUP

"Signature Set?" -> Time Signature Settig

SIGNATURE

44.1kHz

(Initial Setting : 001 bar 04 04(4/4beat))

∞

SETUP

"Tempo Map Set?" -> Tempo Setting

TEMPO

44.1kHz

(Initial Setting : 001 bar 1

=120)

∞

SETUP

"TitleEdit?" -> Program Name Setting

44.1kHz

(Initial Setting : #0001)

∞

SETUP

"Delete PGM?" -> Program Deleting

44.1kHz

(Initial Setting : PGM01)

SURE ?

∞

SETUP

"Click ?" -> Metronome ON/OFF Setting

44.1kHz

(Initial Setting : Off)

∞

SETUP

"Preroll Time?" -> Preroll Time Setting for LOCATE

44.1kHz

function

(Initial Setting : 00s)

∞

SETUP

"MidiSyncOut?" -> MIDI Sync Out Signal Setting

44.1kHz

(Initial Setting : CLK)

∞

139

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

SETUP

"Frame Rate?" -> MTC Frame Rate Setting

44.1kHz

(Initial Setting : 25 frame)

∞

MTC

SETUP

OFFSET

"MTC OFFSET" -> Offset Time Setting between

ABS and MTC

44.1kHz

∞

(Initial Setting : 00h 59m 57s 00f 00sf)

SETUP

"MTC Offset Mode?" -> MTC Offset Mode Setting

44.1kHz

(Initial Setting : ABS)

∞

SETUP

"Slave Mode?" -> Slave Mode ON/OFF Setting

44.1kHz

(Initial Setting : Off)

∞

SETUP

"Slave Type?" -> Slave Mode Type Setting

44.1kHz

(Initial Setting : Vari)

∞

SETUP

"Rec Protect?" -> Record Protect ON/OFF Setting

44.1kHz

(Initial Setting : Off)

∞

SETUP

"Digi. in?" -> Digital Input Track Setting

44.1kHz

(Initial Setting : L--, R--)

∞

SETUP

"Digi. out?" -> Digital Output Track Setting

44.1kHz

(Initial Setting : adat)

∞

SETUP

" Resolution?" -> Bar/Beat Resolution ON/OFF

44.1kHz

Setting

∞

(Initial Setting : Off)

140

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

SETUP

"Device ID?" -> MIDI Device ID Setting

44.1kHz

(Initial Setting : 00)

∞

SETUP

"Sample Rate?" -> Sampling frequency Setting

44.1kHz

(Initial Setting : 44.1kHz)

∞

SETUP

"NOs Of Event?" -> Event Number Chec k of a

Track

44.1kHz

∞

SETUP

"Drive Sel. ?" -> Current Drive Setting

44.1kHz

(Initial Setting : IDE)

∞

SETUP

"Load PGM?" -> Loading Song Data from

External Device

44.1kHz

∞

(Initial Setting : DAT)

LOAD

SETUP

"Save PGM?" -> Saving Song Data to

External Device

44.1kHz

∞

(Initial Setting : DAT)

SAVE

SETUP

FORMAT

44.1kHz

"Disk Format?" -> Initializing Internal Hard disk

/SCSI disk

∞

(Initial Setting : IDE)

* Press either the STOP button or EXIT/NO key to return from the second step to the first or to quit

SETUP mode. The menu will go backwards each time you press either key so that you can correct the

setting, choose another SETUP mode or eventually return to the normal time base display.

141

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2. How to set each Mode

2-1. Track Swapping ("Track Exchange?")

This mode allows you to swap a mono track with one of the other recorded tracks, e.g.

swapping track 1 with track16. Mono track swapping can be done on any two tracks

from track 1 to track 24 including the additional tracks.

The mode also allows you to swap 8 real tracks with 8 additional tracks at once. In this

case, you can either swap tracks 1 ~ 8 with tracks 17 ~ 24 or tracks 9 ~ 16 with

tracks 17

24.

<Note>

You can only swap tracks within a program. It is not possible to swap tracks between

different programs.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display.

Then, press the EXECUTE/YES key. The SETUP display will stop flashing.

2. Choose "Track Exchange?" with the JOG dial. The "?" display will start flashing.

3. Press the EXECUTE/YES key.

You have arrived at the second step of the "Track Exchange?" menu.

The display will now show "Trk=01<->Trk=01" in the current program as in the figure below.

SETUP

44.1kHz

∞

4. Use the JOG dial to enter the track you want.

Then, use either the HOLD/> key or SHUTTLE dial to move the flashing track number so that you

can choose another track.

For example, If you choose "02" on the left hand side "Trk=**" and "08" on the right hand side,

it means you are swapping Track 2 with Track 8.

Even if you chose the numbers the other way round, i.e. Trk=08<->Trk=02, the result would be

the same. In the case you want to swap 8 tracks with the additional tracks, you can choose either

Trk=1-8<->Trk=17-24 with the left hand side "Trk=**" flashing on the display or Trk=17-24<-

>Trk=9-16 with the right hand side "Trk=**" flashing on the display. because these 8 track

settings are situated between Track 24 and Track 01, find them by rotating the JOG dial.

5. Press the EXECUTE/YES key after you have chosen the two tracks you want.

The display will now show "Exchange 02 <-> 08" and be flashing "SURE?".

6. Press the EXECUTE/YES key once again to proceed.

After swapping the recorded data on track 2 with one on track 8, the display will show

"COMPLETED!". Then go back to the normal time base display as before you entered SETUP

mode.

142

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-2. Time Signature Setting ("Signature Set?")

This mode sets up the time signature of a song.

The way it sets this up is, for example, to start a song with a 4/4 beat from the first bar,

then to change it to a 2/4 beat at bar number 17. The time signature and next section

tempo setting make up a tempo map. After the tempo map is figured out by completing

the time signature and tempo setting, the D-160 will be able to handle "BAR /BEAT/

CLOCK" and the metronome function. You need to set up the time signature and tempo

to generate the MIDI Clock & Song Position Pointer.

* Refer to page "117" for details of "MIDI Clock Synchronization".

<Note>

The D-160 will still run the time counter in PLAY mode even after the ABS END. Thus, it will

continue generating the MIDI Clock & Song Position Pointer even if you have not recorded

anything, provided a tempo map has been set up.

* Initial Setting: 001Bar 4/4 Beat

* Available bars: 001

999

* Available time signature: 1/4, 2/4, 3/4, 4/4, 5/4, 1/8, 3/8, 5/8, 6/8, 7/8, 8/8, - -/- - (Delete)

* Maximum setting points : 64

* The setting is applicable song by song.

* The setting can be saved or loaded as a part of the song data

* The setting is memorized even when the power is off.

* Make sure you choose the right program before setting this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display stops flashing.

2. Choose "Signature Set?" with the JOG dial. The "?" display will start flashing.

3. Press the EXECUTE/YES key.

The D-160 will display "SIGNATURE" and the last recalled bar number with the time signature

that has been registered. In the case of the initial setting, as only the first bar is registered with

a 4/4 beat, it will show "001 bar • 4/4 beat".

SETUP

SIGNATURE

44.1kHz

∞

Time Signature Setting Check

4. Turn the JOG dial when the D-160 displays "SIGNATURE".

If there are some setting changes registered in a song, you can see the next set up point by

rotating the JOG dial clockwise. ("*** bar */* )

If you turn the JOG dial fully clockwise, "- - BAR - -/- - " will be displayed.

This means there are no more time signature changing points registered.

<Note>

The D-160 counts a beat with the last registered time signature, i.e. one bar before the "- - bar

- -/- - " . In the case of the initial setting, because only the first bar is registered with a 4/4

beat, the beat counts with a 4/4 beat until the end unless you register a different time

signature after the second bar.

Time Signature Register

5. Press the EXECUTE/YES key when the D-160 displays "SIGNATURE".

The display will show "*** bar" flashing to allow you to enter a new time signature changing

point.

143

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

6. Use either the HOLD/> key or SHUTTLE dial to choose "bar" or " beat". Then, use the JOG

dial to enter the bar number or time signature you want.

The bar numbers you can enter are from 001 to 999. And the time signatures you can enter are

"1/4, 2/4, 3/4, 4/4, 5/4, 1/8, 3/8, 5/8, 6/8, 7/8, 8/8". For your information, the "- -/- -" means

"No Signature registered" and can be used to delete a signature change point. When you turn

the JOG dial while the display shows "*** bar" flashing, it will either show the time signature as

"*/*" on the already registered bars or as "- -/- -" if a bar has no time signature registered.

7. Press the EXECUTE/YES key after you have entered a required bar number and time signature.

The setting will now be registered. Then, the display will go back to Item 5 and show "*** bar"

flashing, allowing you to enter a new time signature setting.

8. Repeat the procedures described in items 5

7 to register further time signatures.

* Press either the STOP button or EXIT/NO key to return from the second step to the first

or to quit SETUP mode. The menu will go backwards each time you press either key so that

you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

<Note>

You can register the setting up to 64 points. If you try to register over 64 points, the 65th

point onwards will be ignored.

Time Signature Edit & Delete

Follow the procedures described as in Items 1

6. When the display shows flashing "*** bar", choose the bar that carries the signature you want to

edit with the JOG dial.

7. Press the HOLD/> key or turn the shuttle dial to choose the "*/* ".

The flashing display will move to the "*/* " and allows you to change the time signature setting.

8. With the JOG dial, choose a required time signature.

If you choose "- -/- -", the time signature on the bar will be deleted.

9. Press the EXECUTE/YES key after you have changed or deleted the time signature on the bar

number you wanted.

The setting will now be registered. Then, the display will return to Item 5 and show "*** bar"

flashing, which allows you to enter a new time signature setting.

* Press either the STOP button or EXIT/NO key to return from the second step to the first

or to quit SETUP mode. The menu will go backwards each time you press either key so that

you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

<Notes>

* You cannot register the "- -/- -" setting on the 001bar.

* If the registered tempo changing point becomes unavailable, after you alter the time

signature, the particular beat which used to carry some tempo changing will automatically

disappear. For example, the registered tempo at 010 bar 4 will disappear if you edit the

time signature at the 010 bar to 3/4 beat.

Delete all Time Signature Setting at once

Follow the procedures described as in items 1

6. While the display shows "*** bar" flashing, turn the JOG dial fully counter clockwise.

The display will now show "All Clear?" and flashing "SURE?".

7. Press the EXECUTE/YES key to proceed.

All the registered time signature settings will be erased and go back to the initial setting.

Then, the display will go back to item 5 and show "*** bar" flashing.

<Note>

Be careful because this procedure wipes out the tempo setting as well as time signature

setting.

144

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

* Press either the STOP button or EXIT/NO key to return from the second step to the first

or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

2-3. Tempo Setting ("Tempo Map Set?")

This mode sets up the tempo on a song. The way it sets this up is, for example, for the

tempo to become 150 bpm at the 3rd beat in the 12th bar.

The tempo setting and time signature in the previous section make up a tempo map.

After the tempo map has been calculated by completing the tempo and time signature

setting, the D-160 will be able to handle "BAR /BEAT/CLOCK" and the metronome

function. You need to set up the tempo and time signature to generate the MIDI Clock &

Song Position Pointer.

* Refer to page "117" for details of "MIDI Clock Synchronization".

<Note>

The D-160 will still run the time counter in PLAY mode even after the ABS END. Thus, it will

continue generating the MIDI Clock & Song Position Pointer even if you have not recorded

anything, provided a tempo map has been set up.

* Initial Setting: 001Bar 1st Beat 120 bpm

* Bar to register: Follows to the time signature setting

* Beat to register : Follows to the time signature setting

* Available tempo : 30

250, - - (Delete)

* Maximum setting points : 64

* The setting is applicable song by song.

* The setting can be saved or loaded as a part of the song data

* The setting is memorized even when the power is off.

Make sure you choose the right program before setting this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display.

Then, press the EXECUTE/YES key. The SETUP display will stop flashing.

2. Choose "Tempo Map Set?" with the JOG dial. The "?" display will start flashing.

3. Press the EXECUTE/YES key.

The D-160 will display "TEMPO" and last recalled bar number with its tempo setting which is

already registered. In the case of the initial setting, because only the first bar, first beat is registered

with a 120 bpm, it will show "001 bar ,1 • =120 ".

SETUP

TEMPO

44.1kHz

∞

Tempo Setting Check

4. Turn the JOG dial when the D-160 displays "TEMPO".

If there are some setting changes registered in a song, you can see the next set up point by

rotating the JOG dial clockwise.("*** bar * =***)

If you turn the JOG dial fully clockwise, "- - BAR - - , = - -" will be displayed.

This means there is no more tempo changing points registered.

<Note>

The D-160 counts a beat with the last registered tempo, i.e. one bar before the "- - bar - - ,

= - -" . In the case of the initial setting, because only the first beat of first bar is registered

with a 120bpm, the beat counts with a 120bpm until the end unless you register a different

tempo after the second beat of first bar.

145

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

Tempo Register

5. Press the EXECUTE/YES key when the D-160 displays "TEMPO".

The display will show flashing "*** bar" so that it allows you to enter a new tempo changing

point.

6. Use either the HOLD/> key or SHUTTLE dial to choose "bar", " beat" or "TEMPO".

Then, use the JOG dial to enter a required bar/beat and tempo that you want to register.

The bar numbers and beat you can enter follows the time signature setting described in the

previous section, and the tempo settings you can enter are 30 ~ 250 bpm. For your information,

the "- - -" means "No tempo setting registered" and can be used to delete a tempo change point.

When you turn the JOG dial while the display shows "*** bar" or "* " flashing, it will either

show the tempo as "***" on the already registered bar/beat or as "- - -" if a bar/beat has no tempo

setting registered.

7. Press the EXECUTE/YES key after you have entered a required bar/beat and tempo.

The setting will now be registered. Then, the display will go back to Item 5 and show "*** bar"

flashing so which you to enter a new tempo setting.

8. Repeat the procedures described in items 5 ~ 7 to register further tempo settings.

* Press either the STOP button or EXIT/NO key to return from the second step to the first or

to quit SETUP mode. The menu will go backwards each time you press either key so that you

can correct the setting, choose some other SETUP mode or eventually return to the normal

time base display.

<Note>

You can register the setting up to 64 points. If you try to register over 64 points, the 65th point

onwards will be ignored.

Example : A tempo map can be setup as in the following example, i.e. set the required tempo after having set

time signature.

Tempo Map

Time Signature Setting

001 bar 4/4

Tempo Setting

001 bar 1

003 bar 1

005 bar 3

007 bar 2

=120

=90

005 bar 3/4

=60

=120

Tempo Setting Edit or Delete

Follow the procedures described as in Items 1 ~ 5.

6. Use either the HOLD/> key or SHUTTLE dial to choose "bar", " beat" or "TEMPO".

Then, use the JOG dial to enter a required bar/beat and tempo that you want to edit.

The display will show tempo as "***" on the already registered bar/beat.

7. Press the HOLD/> key or turn the shuttle dial to choose the " =*** ".

The flashing display will move to " =*** " so that it allows you to change the tempo setting.

8. With the JOG dial, choose a required tempo.

If you choose "- - -", the tempo setting on the bar/beat will be deleted.

9. Press the EXECUTE/YES key after you have changed or deleted the tempo setting on the bar/

beat you wanted.

The setting will now be registered. Then, the display will go back to Item 5 and show "*** bar"

flashing, which allows you to enter a new tempo setting.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other setup mode, or eventually return to the

normal time base display.

<Note>

You cannot register the "- - -" at the 001 bar 1

146

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

Delete all Tempo Setting at once

If you proceed with "Delete all Time Signature Setting at once" as described in the previous

section, the D-160 will erase all the tempo settings as well as the time signature settings.

* Refer to the "Delete all Time Signature Setting at once" section for details.

2-4. Program Title Setting ("Title Edit PGM?")

This mode gives a name to the individual program (maximum of 99 programs).

Also, the registered name can be edited.

Choose a required program before you enter to the SETUP mode if you are newly giving

a title or editing a title.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display stops flashing.

2. With the JOG dial, choose "TitleEdit PGM?".

The "?" display will start flashing.

3. Press the EXECUTE/YES key.

The D-160 will enter the second step menu of "TitleEdit PGM?" and show the current program

title. In the case of the initial setting, the display will show "#0001" with "#" flashing.

The flashing digit allows you to enter a letter. The available letters are a maximum of 16 digits of

alphabet or numbers. The D-160 handles ASCII code.

SETUP

44.1kHz

∞

4. Use the JOG dial to enter a required letter. Then, use either the HOLD/> key or SHUTTLE dial to

move the flashing digit.

5. Press the EXECUTE/YES key after you have entered the required title.

The title will now be registered and the display will then go back to the normal time base display

as before you entered SETUP mode.

2-5. Program Delete ("Delete PGM?")

This mode allows you to delete program data which you no longer need.

You can delete the currently chosen program to obtain more recording space.

<Notes>

* The D-160 automatically renumbers the remained programs after deleting a program between

the other two programs. For example, if you delete program number 2 of program numbers

1,2,3 and 4, number 3 will automatically become the new program number 2 and number

4 will become the new program number 3. Then, the D-160 will end up having three programs

rather than four.

* If you try to delete program number 1 when there is only one program available, the D-160

will set up a new blank program 1 after erasing the current program 1 data.

* This program delete mode does not have an "UNDO" function.

* The Program delete mode will not work if the "Rec Protect ?" mode is set to On. The D-160

will display "Disable REC!" as a warning message and go back to the normal time base

display the same as before you entered SETUP mode.

147

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose "Delete PGM?". The "?" display will start flashing.

3. Press the EXECUTE/YES key.

The display will start flashing "SURE?" which indicates it is ready to delete.

SETUP

44.1kHz

SURE ?

∞

4. Press the EXECUTE/YES key once again to proceed.

The D-160 will show "Deleting!" while proceeding and "COMPLTETED!" after deleting the currently

displayed program. The display will then go back to the normal time base display on the program

before the one you deleted.

2-6. Metronome Setting ("Click ? " )

The D-160 is able to generate the metronome click tone according to the tempo map

figured out by the time signature and tempo setting.

You can record a track at the same time as listening to the metronome click tone.

If you set this mode to ON, track 16 will generate the metronome click tone in either play

or record mode.

<Notes>

*If you set this mode to ON, the D-160 cannot playback the recorded sound from track 16, as

track 16 will be the click track exclusively. In conjunction with this, do not record track 16

with this mode on. If track 16 is in record mode, the click will not be generated.

*The D-160 will still run the time counter in PLAY mode even after the ABS END. Thus, it will

continue generating the metronome click tone even if you have not recorded anything, provided

a tempo map has been set up.

* Initial setting : Off

* Available setting : Off, On

* The setting is applicable song by song.

* The setting can be saved or loaded as a part of song data

* The setting is memorized even when the power is off.

Make sure to choose the right program before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display.

Then, press the EXECUTE/YES key. The SETUP display stops flashing.

2. With the JOG dial, choose "Click ?". The "?" display will start flashing.

3. Press the EXECUTE/YES key.

The display will start flashing either "Off" or "On" of current setting.

In the case of initial setting it will show "Off".

SETUP

44.1kHz

∞

4. Choose either ON or OFF with the JOG dial.

On : Click tone will be generated.

Off : Click tone will not be generated.

148

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

5. Press EXECUTE/YES key after choosing the setting you want.

* Press either the "STOP" button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

2-7. Preroll Time Setting ("Preroll Time ? ")

The D-160 has a preroll function, which stops at the backwards specified time location.

This function is useful when you want to start monitoring the recorded audio from just

before a locate point.

Locate Point

Locate

You can set 'backwards specified locate point.

Stop Point

* Initial setting : 00sec

* Available setting : 00

10sec in 1sec step

* The setting is applicable song by song.

* The setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the powering off.

Make sure to choose the right program before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Preroll Time?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of initial setting, it will show 00 second.

3. Press the EXECUTE/YES key.

The current setting will start flashing “**” which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, enter the required preroll time.

You can set the preroll time between 0 and 10 sec in 1 second steps.

If you turn the JOG dial clockwise, the time value will increase. And if you turn the JOG dial

counter clockwise, the time value will decrease vise versa.

5. Press the EXECUTE/YES key after you have entered the preroll time you want.

The setting will be registered and the display will go back to the Item 2 above.

* Press either the “STOP” button or EXIT/NO key to return from the second step menu to the

first or to quit the SETUP mode. The menu will go backwards each time you press either key

so that you can correct the setting, choose some other SETUP mode or eventually return to

the normal time base display.

149

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-8. MIDI Sync Signal Output Setting (“Midi Sync Out ?”)

This mode sets up the type of MIDI sync signal for external MIDI equipment.

The type of signal the D-160 outputs is either MIDI Clock & Song Position Pointer or MTC

(MIDI Time Code). Choose one so that the external MIDI equipment can recognize it

when synchronizing to the D-160.

In case of the MIDI Clock & Song Position Pointer, you need to set the section "2-2. Time

Signature" and section "2-3.Tempo as previously mentioned."

In case of the MTC ( MIDI Time Code), you need to set the section "2-9. MTC Frame Rate",

"2-10. MTC Offset Time" and "2-11. MTC Offset Mode" described below.

* See page "117" “MIDI Synchronization Function” for details of the MIDI sync.

<Note>

The D-160 will still run the time counter in PLAY mode even after the ABS END. Thus, it will

continue generating the MIDI Clock & Song Position Pointer and MTC even if you have not

recorded anything, provided a tempo map has been set up.

* Initial setting : CLK

* Available setting : CLK, MTC, Off

Clock : MIDI Clock & Song Position Pointer, MTC : MIDI Time Code

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the power is off.

Make sure to choose the right program before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “MidiSyncOut?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of initial setting, it will show CLK.

3. Press the EXECUTE/YES key.

The current setting will start flashing “**” which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, enter a required Midi Sync Signal.

Choose the type of MIDI signal you want.

If you choose “CLK”, the D-160 generates the MIDI Clock & Song Position Pointer.

If you choose “MTC”, the D-160 generates the MIDI Time Code.

If you choose “Off”, the D-160 generates no MIDI Sync signal.

5. Press the EXECUTE/YES key after you have entered the Midi Sync Signal you wanted.

The setting will be registered and the display will go back to step 2 above.

* Press either the “STOP” button or EXIT/NO key to return from the second step menu to

the first or to quit SETUP mode. The menu will go backwards each time you press either key

so that you can correct the setting, choose some other SETUP mode or eventually return to

the normal time base display.

150

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-9. MTC Frame Rate Setting (“Frame Rate?”)

If you choose MTC as the MIDI sync signal in the previous section “2-8. MIDI Sync Signal

Output Setting”, you need to set up this mode.

You can set up the frame rate of the MTC generated for external MIDI equipment such as

computer based sequencer software. Choose the frame rate so that the external MIDI

device can receive it.

* See page "120" “MIDI Synchronization Function” for details of the MTC sync.

<Note>

The D-160 will still run the time counter in PLAY mode even after the ABS END. Thus, it will

continue generating the MTC even if you have not recorded anything.

* Initial setting : 25 Frames

* Available setting : 24, 25, 30df, 30nd,29df, 29nd

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the power is off.

Make sure to choose the right program before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Frame Rate?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of initial setting, it will show 25 frames.

3. Press the EXECUTE/YES key.

The current setting will start flashing “**” which indicates it is ready to change the setting.

SETUP

44.1kHz

∞

4. With the JOG dial, enter the frame rate you want.

Choose the frame rate you want from;

24, 25, 30 non drop frame, 30 drop frame, 29nd (29.97 non drop frame) and 29df (29.97 drop

frame).

5. Press the EXECUTE/YES key once again.

The setting will be registered and the display will go back to the Item 2 above.

* Press either the “STOP” button or EXIT/NO key to return from the second step menu to the

first or to quit the SETUP mode. The menu will go backwards each time you press either key

so that you can correct the setting, choose some other SETUP mode or eventually return to

the normal time base display.

<Note>

There are no 29.97nd or 29.97df in the MTC standard. Use either 30nd or30df unless you

definitely need to synchronize the D-160 with NTSC video.

151

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-10. MTC Offset Time Setting (“MTC Offset”)

If you choose the MTC as the MIDI sync signal in the previous section “2-8. MIDI Sync

Signal Output Setting”, you need to set up this mode.

You can set up the offset time between the MTC output and internal ABS time.

In the case of the initial setting, MTC will output 00h 59m 57s 00f 00sf at the ABS 00h

00m 00s 00f 00sf point which is ABS 0. You can also set the MTC offset based on the

001BAR 1BEAT 00CLK position rather than ABS 0.

Refer to the next section “2-11. MTC Offset Mode Setting” for details.

* See “Before Operation” section “3. Time base” for the time relation between MTC and

ABS or BAR/BEAT/CLK.

* See page "120" MIDI synchronization function for details of the MTC sync.

<Note>

The D-160 will still run the time counter in PLAY mode even after the ABS END. Thus, it will

continue generating the MTC even if you have not recorded anything.

* Initial setting : 00h 59m 57s 00f 00sf

* Available setting : 00h 00m 00s 00f 00sf ~ 23h 59m 59s 29f 99sf

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the power is off.

Make sure to choose the right program before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “OFFSET”.

The display will show the current setting. In the case of initial setting, it will show 00h 59m 57s

00f 00sf.

3. Press the EXECUTE/YES key.

The “s” , second digits, display will start flashing which is asking you to specify the second digit

of the offset time you want.

MTC

SETUP

OFFSET

44.1kHz

∞

4. Use either the HOLD/> key or SHUTTLE dial to choose time digits, i.e. “h”, “m”, “s”, “f”, “sf”.

Then, use the JOG dial to enter the required time value that you want to register.

The available setting is from 00h 00m 00s 00f 00sf to 23h 59m 59s 29f 99sf.

5. Press the EXECUTE/YES key after you have entered the required Offset.

The MTC Offset will now be registered and the display will then go back to Item 2 above.

* Press either the “STOP” button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key.

<Note>

We recommend you set about three seconds of preroll time because in the MTC OFFSET of

00h 59m 57s rather than 01h 00m 00s, considering the preparation time to start the external

sequencer in the event that you have chosen “ABS” in the MTC OFFSET mode.

152

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-11. MTC Offset Mode Setting (“MTC Offset?”)

If you choose the MTC as the MIDI sync signal in the previous section “2-8. MIDI Sync

Signal Output Setting”, you need to set up this mode. This mode chooses the MTC time

with offset, which you have already set in the previous section, to start either from the

ABS 0 position or from the 001 BAR 1 BEAT 00 CLK on the tempo map.

* See “Before Operation” section “3.Time base” for the time relation between MTC and

ABS or BAR/BEAT/CLK.

* See page "120" MIDI synchronization function for details of the MTC sync.

<Note>

The D-160 will still run the time counter in PLAY mode even after the ABS END. Thus, it will

continue generating the MTC even if you have not recorded anything.

* Initial setting : ABS

* Available setting : ABS, BAR

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the powering is off.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Offset Mode?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of the initial setting, it will show ABS.

3. Press the EXECUTE/YES key.

The current setting will start flashing which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, enter a required setting either ABS or Bar

If you choose the “ABS”, the MTC time with offset will output at the ABS 0 position.

If you choose the “Bar ”, the MTC time with offset will output at the 001 BAR 1 BEAT 00 CLK

position which according to the tempo map.

5. Press the EXECUTE/YES key once again.

The setting will be registered and the display will go back to step 2 above.

* Press either the “STOP” button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

<Note>

We recommend that you set about three seconds of preroll time as in the MTC OFFSET of 00h

59m 57s rather than 01h 00m 00s, considering the preparation time to start the external

sequencer in the event that you have chosen “ABS” in the MTC OFFSET mode. If you have

chosen “Bar ” , the D-160 automatically sets two bars worth of preroll time. You can leave the

MTC OFFSET as 01h 00m 00s.

153

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-12. Slave Mode Setting (“Slave Mode”)

This mode allows you to choose the D-160 slave mode setting either ON or OFF.

If you set the mode to ON, the D-160 will synchronize to the incoming MTC(MIDI time

code)from master unit. It will also synchronize to a type of external sync signal which

you have chosen with the section “2-14. Sync Signal Setting”.

You can make up a multi track recording system using Fostex D-90, D-80 (Ver 2), DMT-8

(Ver 2) or DMT-8VL, and also with some sequencer software.

* See Page "117" for MIDI synchronization for more details.

* Initial setting : Off

* Available setting : On, Off

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the power is off.

Make sure to choose the right program before setting up this mode.

Make sure you choose the right sampling frequency before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Slave Mode?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of the initial setting, it will display Off.

3. Press the EXECUTE/YES key.

The current setting will start flashing which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, choose either “On” or “Off”.

If you choose “Off”, the slave function will not work.

5. Press EXECUTE/YES key after choosing the setting you want.

If you have chosen “Off”, the display will go back to step 2 described above.

However, if you have chosen “On”, as well as the display going back to step 2, the “CHASE”

indicator on the display will start flashing.

This means that the Slave Mode has been set to On but, “Chase Lock” has not been achieved yet.

When the “Chase Lock” is completed, the “CHASE” indicator will stop flashing.

You can now choose which type of sync signal the D-160 should follow, after you have set this

mode to On. Refer to next section “2-13. Slave Type Setting” for more details.

6. Press either the STOP button or EXIT/NO key to go back to the normal time base display before

entering the SETUP mode.

154

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-13. Slave Mode Type Setting (“Slave Type?”)

If you have set the Slave Mode to ON in the previous section “2-12. Slave Mode Setting”,

you can choose what type of external sync signal that the D-160 synchronizes to.

This mode allows you to choose the external sync signal type.

* See Page "117" for MIDI synchronization for more details.

* Initial setting : Vari

* Available setting : Vari, SPDIF, adat, Free

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the power is off.

Make sure you choose the right program before setting up this mode.

Make sure you choose the right sampling frequency before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Slave Type?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of the initial setting, it will show Vari.

3. Press the EXECUTE/YES key.

The current setting will start flashing which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, choose the setting you want.

If you choose “Vari”, the D-160 as a slave will only rely on the incoming MTC while synchronizing.

If you choose “SPDIF”, the D-160 will lock to the MTC first. Then, it will sync lock to the incoming

SPDIF digital signal.

If you choose “adat”, the D-160 will lock to the MTC first, Then, it will sync lock to the incoming

adat digital signal.

If you choose “Free”, the D-160 will freely play back on its own internal clock, after locking to the

MTC.

<Note>

You need to connect an external MTC whatever type of sync signal you have chosen.

5. Press EXECUTE/YES key after choosing the setting you want.

The display will then go back to step 2 described above.

<Note>

If you have chosen either “SPDIF” or “adat” as a sync signal, the “DIGITAL” indicator on the

display will light up provided the appropriate digital signal has been input. If the signal you

input is not suitable for the setting, the display will start flashing “DIGITAL” and “FS” indicator.

The FS means sampling frequency and it is only applicable to the SPDIF signal.

6. Press either the STOP button or EXIT/NO key to go back to the normal time base display before

entering the SETUP mode.

* Press either the “STOP” button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

155

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

<Notes>

* The re-chase window of the D-160 is fixed at 10 frames. This means that when the time

difference(offset)between a master machine and the slave D-160 becomes larger than 10

frames, the D-160 will recognize it is out of chase lock and re-chase the position again. The D-

160 will mute its audio during the re-chasing process. However, if the difference between

two machines is less than 10 frames, the slave D160 will ignore the difference and run it as it

is.

* The digital signal used with the Slave Mode is solely for sync lock. If you want to record a

digital signal, follow the procedure as described in sections “2-15. Digital Input Track Setting”.

For your information, the digital signal you set with the “2-15. Digital Input Track Setting”

for recording will override and be prioritized over the external sync signal which you have

chosen this mode.

* The Vari Pitch function will be automatically OFF if you set the Slave Mode to ON.

* The D-160 will mute audio for about two seconds when it locks/unlocks the external sync

source if you have chosen the slave type to “SPDIF” or “adat”.

To avoid this problem, supply a reliable and stable digital source signal to the D-160.

2-14. Record Protect Setting (“Rec Protect?”)

The D-160 carries a record prohibit function.

This function works as if you had removed the Record Protect tag from a conventional

compact cassette tape. This mode allows you to choose either the ON or OFF function.

* Initial setting : Off

* Available setting : Off, On

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the power is off.

Make sure you choose the right program before setting up this mode.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Rec Protect?”.

The “?” display will start flashing.

3. Press the EXECUTE/YES key.

The display will start flashing either “Off” or “On” of current setting.

In the case of the initial setting, it will display “Off”.

SETUP

44.1kHz

∞

4. Choose either On or Off with the JOG dial.

If you choose “Off”, there is no protection and you can record, paste, erase, etc. over it.

If you choose “On”, there is protection and you cannot record, paste, erase, etc. over it.

5. Press the EXECUTE/YES key again to proceed.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit the SETUP mode. The menu will go backwards each time you press either key

so that you can correct the setting, choose some other SETUP mode or eventually return to

the normal time base display.

<Note>

If you set this mode to record protect, the D-160 will not perform such functions as recording,

pasting or erasing. And it will show “Disable REC” on the display for one second as a warning

message. Change the protect mode setting to “OFF” in this situation.

156

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-15. Digital Input Track Setting (“Digi. In?”)

This mode sets up the incoming digital signal to assign the D-160 recording track you

have chosen. Using this function to digitally record from external digital equipment.

The SPDIF stereo digital signal can assign D-160 tracks from track 1 to track 16 according

to what pair you want.

In the case of adat digital signal input, this mode will assign 8 track adat signals to either

tracks 1 ~ 8 or 9 ~ 16. You need to set the D-160 sampling frequency to match the

incoming digital signal sampling frequency.

* Initial setting : L- - R- - (Nothing is assigned on Lch and Rch)

* Available setting : Lch = 1 ~ 16, adat, - -(No assign) Rch = 1 ~ 16, - - (No assign)

* This setting is commonly applicable to all the programs .

* This setting cannot be saved or loaded.

* The setting is memorized even when the power is off.

<Notes>

* The D-160 has two sets of DATA INPUT connectors: 1-8 and 9-16.

In the case of adat, change over the connection depending on which group of tracks you

want to assign the digital signal to. In the case of SPDIF, the signal input can only be done

via the DATA INPUT 1-8 connector. Do not use the 9-16 connector. The input signal will be

applicable to all 16 tracks.

* The D-160 will mute audio for about two seconds when it locks/unlocks the external sync

source if you have chosen the slave type to “SPDIF” or “adat”. To avoid this, supply a

reliable and stable digital source signal to the D-160.

* Again, remember that you need to set the D-160 sampling frequency to match the incoming

digital signal sampling frequency.

* The D-160 cannot record digitally if the D-160 sampling frequency is different from the

incoming SPDIF digital signal sampling frequency.

* In the case of the adat digital signal input, the D-160 will record the signal digitally but

with the incorrect speed. This is because, when the D-160 has been set up with this mode

ON, the D-160 will be working in the external word clock sync mode, i.e. incoming SPDIF or

adat signal clock timing runs the D-160 internal clock rather than the D-160's own internal

clock. In the case of the SPDIF signal, it contains the sampling frequency information in the

signal itself. So, the D-160 will recognize if the incoming sampling frequency is different

from the one set up in the D-160 and refuse to synchronize to it. However, an adat signal

does not contain this sampling frequency info as in the standard. The D-160 will ignore the

sampling frequency difference and synchronize with the incorrect rate and record at the

wrong speed.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Digi.In?”.

The “?” display will start flashing. The display will also show the current setting. In the case of the

initial setting, it will show “L- - R- -”.

3. Press the EXECUTE/YES key.

The current assign setting on the Lch will start flash asking you to choose the setting you want.

SETUP

44.1kHz

∞

157

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

4-A. In the case of SPDIF signal input, enter whichever two tracks you want with the JOG dial.

Use either the HOLD/> key or SHUTTLE dial to move the flashing Channel display between Lch

and Rch.

Available track settings are tracks 1 ~ 16 and “- -” which means no tracks are assigned.

<Note>

You cannot assign the same track to both Lch and Rch. If you accidentally do this, the later

setting will be effective and the D-160 will automatically cancel the previous track assignment

to “- -”, so that nothing is assigned there. The later setting will always be prioritized.

* The D-160 can also record only one channel from the stereo SPDIF signal.

For example, if you assign Lch to track 4 and Rch to NIL, “L04 R- -”, the D-160 will record

only SPDIF Lch on track 4.

4-B. For an adat digital signal, enter “adat” with the JOG dial after making the Lch flash with either

the HOLD/> key or SHUTTLE dial.

You cannot choose “adat” when the Rch is flashing.

* The adat digital input signal will be assigned as DATA INPUT 1-8 to tracks 1 ~ 8 and

DATA INPUT 9-16 to tracks 9 ~ 16 accordingly.

* For analog input, you need to select nothing on either the Lch and Rch.

5. Press the EXECUTE/YES key to register the tracks you have chosen.

The display will go back to the display of item 2.

When the D-160 recognizes an incoming digital signal correctly, the red “digital” display will

stop flashing.

* If the red “DIGITAL” indication is flashing, check the connection and cable between D-160

and the external digital equipment.

<Notes>

* If you set up the wrong sampling frequency for the incoming SPDIF, the display will flash

either 44.1k or 48kHz on the FS indicator as a warning message.

* For adat signal input, there is no warning message indication. Be careful of the frequency

sampling setting.

6. Press the STOP button or EXIT/NO key to exit this mode.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode, or eventually return to

the normal time base display.

<Notes>

* Tracks assigned for digital input will become exclusively digital input only. Hence no

analog recording on those tracks is possible. If you want to use some D-160 tracks for

analog input, you have to select “- -” in both the Lch and the Rch or assign some other

tracks. In the “adat” setting, either tracks 1-8 or 9-16 will automatically be assigned for

digital input. So, the tracks which have not been assigned can still be used for analog

recording. For example, if you connect the adat signal to DATA INPUT 1-8, you can

record digital on tracks 1-8 and analog on tracks 9-16. The D-160 can manage digital/

analog 16 track simultaneous recording.

* Vari Pitch function will be automatically OFF ( No LED lights up), when you set up this

digital input mode.

* The input digital signal you choose in this mode will override the type of external sync

signal you might have chosen with “2-12. Slave Mode Setting” such as Vari, SPDIF, adat or

Free. Therefore, the D-160 will ignore the Slave Mode setting and the slave function will

become the sync lock synchronization with the chosen input digital signal in this mode.

158

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-16. Digital Out Track Setting (“Digi. out?”)

This mode sets up the outgoing digital signal from the D-160 with what type and which

recorded tracks. The D-160 can digitally transmit the recorded audio as it is to external

digital equipment. When you use this function, set the identical sampling frequency on

the external digital equipment as the D-160 sampling frequency.

* Initial setting : adat

* Available setting : adat, Lch 1 ~ 16, Rch 1 ~ 16

* This setting is commonly applicable to all programs.

* This setting cannot be saved or loaded.

* The setting is memorized even when the power is off.

<Note>

S/P DIF output (1 ~ 16) will all be output from DATA OUTPUT 1-8.

DATA OUTPUT 9-16 is constantly fixed to "adat" output.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Digi.out?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of the initial setting, it will show “adat”.

3. Press the EXECUTE/YES key.

The current setting will start to flash which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4-A. If you want to choose an SPDIF digital signal, when the Lch display is flashing, choose the

track you want with the JOG dial.

Then, use the HOLD/> key or SHUTTLE dial to move to the Rch. Using the same method for

choosing the Lch, choose the track in the Rch.

If you choose normal numerical pairs such as “L01-R02”, “L03-R04”, ........“L13-R14”, “L15-R16”,

a two channel stereo signal will be transmitted in SPDIF digital audio format.

In this case, the odd channels will be directed to the Lch and even channels to the Rch accordingly.

<Note>

You cannot assign the same track to both Lch and Rch. If you accidentally do this, the Lch

setting will be effective and the D-160 will automatically cancel the Rch track assignment to “-

-” as nothing is assigned. For example, if you chose channel 02 for both Lch and Rch and

pressed the EXECUTE/YES key, the D-160 would automatically assign as “L02 - R- -”.

4-B. In the case that you want to choose an adat signal, when the Lch display is flashing, choose

“adat” with the JOG dial. As you cannot choose “adat” while the Rch display is flashing, use

the HOLD/> key or SHUTTLE dial to move to the Lch.

All 16 track signals will be transmitted in adat digital format.

* The adat digital output signal will be assigned as tracks 1 ~ 8 to DATA OUTPUT 1-8 and

tracks 9 ~ 16 to DATA OUTPUT 9-16 accordingly.

5. Press the EXECUTE/YES key to register the tracks you have chosen.

The display will go back to the display of Item 2.

6. Press the STOP button or EXIT/NO key to come out of this mode.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

159

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

* All the analog output tracks are available regardless of the above settings.

2-17. Bar/Beat Resolution Mode Setting (“ Resolution?”)

This mode sets up the display resolution mode in either “ON” or “OFF”.

If you set this mode to “ON”, the D-160 will register the memory points rounding up or

down so that clock digits are always kept at 00. This mode is only relevant when you

choose Bar/Beat/Clock as a time base.

This function is very useful for edit functions such as copy paste or move paste when you

use the Bar/Beat/Clock as the time base. For example, when you register a memory point

that picks up a real time in play mode, you press the STORE button and then some

memory keys. The position you choose will be automatically corrected based on the Bar/

Beat resolution. The position will always register in clock accuracy. This setting is

memorized even when the power is off.

* For example, if you are to register 001 Bar 1 Beat 46 Clock to the CLIP BOARD IN point and

002 Bar 4 Beat 51 Clock to the CLIP BOARD OUT point, if the resolution mode is set, the actual

memory will be corrected in the following key. This example is mentioned based on the time

signature of a 4/4 Beat.

001 Bar 1 Beat 46 Clock -> 001 Bar 1 Beat 00 Clock : round down on clock

002 Bar 4 Beat 51 Clock -> 003 Bar 1 Beat 00 Clock : round up on clock

* Initial setting : Off

* Available setting : Off, On

* This setting is commonly applicable to all the programs.

* This setting cannot be saved or loaded.

* The setting is memorized even when the power is off.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display stops flashing.

2. With the JOG dial, choose “ Resolution?”.

The “?” display will start flashing. The display will also show the current setting. In the case of the

initial setting, it will show “Off”.

3. Press the EXECUTE/YES key.

The current setting will start flashing which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, choose either “On” or “Off”.

If you choose “Off”, the slave function will not work.

If you choose “On”, the clock will be rounded up or down always ending in 00.

5. Press EXECUTE/YES key after choosing the setting you want.

The display will go back to the display of item 2.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to the

normal time base display.

160

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-18. MIDI Device ID Setting (“Device ID?”)

This mode sets up the MIDI device ID number on the D-160.

The set ID applies to bothreceiving and transmitting when an external sequence software

controls the D-160 via MMC or the Fostex system Exclusive Message.

This mode is necessary to arm the slave machine record track selectors from the master

machine. The available device ID is between 00 and 99. But, if the D-160 receives a

message with ID No 7F, The D-160 will recognize it and follow the command regardless of

the device ID setting.

* Initial setting : 00

* Available setting : 00 ~ 99

* This setting is applicable to all programs.

* This setting cannot be saved or loaded.

* The setting is memorized even when the power is off.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Device ID?”.

The “?” display will start flashing.

The display will also show the current setting. In the case of the initial setting, it will show “00”.

3. Press the EXECUTE/YES key.

The current setting will start flashing “**” which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, enter a required ID number.

The available setting is from 00 ~ 99.

5. Press the EXECUTE/YES key once again.

The setting will be registered and the display will go back to step 2.

* Press either the STOP button or EXIT/NO key to return from the second step to the

first or to quit SETUP mode. The menu will go backwards each time you press either

key so that you can correct the setting, choose some other SETUP mode or eventually

return to the normal time base display.

161

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-19. Sampling Frequency Setting (“Sample Rate?”)

The D-160 can handle two types of sampling frequency, either 44.1k or 48 kHz.

This mode allows you to set either sampling frequency. The display will show the registered

sampling frequency.

* Initial setting : 44.1kHz

* Available setting : 44.1kHz, 48kHz

* This setting is applicable song by song.

* This setting can be saved or loaded as a part of the song data.

* The setting is memorized even when the power is off.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display.

Then, press the EXECUTE/YES key. The SETUP display stops flashing.

2. With the JOG dial, choose “Sample Rate?”.

The “?” display will start flashing. The display will also show the current setting. In the case of the

initial setting, it will show “44.1”.

3. Press the EXECUTE/YES key.

The current setting will start flashing which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, choose either “44.1” or “48” .

5. Press the EXECUTE/YES key to process.

The setting will be registered and the display will go back to step 2. Or If you are not changing

the sampling frequency, press the EXIT/NO key or STOP button to quit the SETUP mode.

6. Press the STOP button or EXIT/NO key to come out of this mode.

The display will go back to the normal time base display.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to

the normal time base display.

<Notes>

* The total recording length will be shorter with 48kHz sampling than 44.1kHz sampling due

to the hard disk space usage. The REMAIN time display will be shorter with 48kHz than

44.1kHz as well.

* Except for certain special use, avoid changing the sampling frequency within a program .

It is possible to set the D-160 to a different sampling frequency than its original song

recording frequency. However, the play back speed will become different from the original

and the registered memory key data will become a different value.

162

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-20. Event Number Check on Each Track (“NOs Of Event?”)

This mode allows you to check event numbers on each recorded track individually.

As we have described in the “Before Operation” section, each recorded track data (TRK 1

~ 24) on a program is made up with the Audio Files and 0 Files.

The event number is calculated by adding these two types of Files.

The D-160 is able to carry up to 512 events per track. When the event numbers exceed

508, the D-160 will no longer be able to record new data. This situation is called “event

over”.

For an ordinary song length, about 6 minutes, however intense the editing process is,

you should never experience an event over problem.

This is because the D-160 automatically tries to optimize the disk management system as

much as possible so that the event numbers are always kept minimum.

However, you need to be careful in certain circumstances as:

* when recording short lengths of audio bit by bit in many separate places.

* when taking advantage of a D-160 feature in which you can record wherever

you like within the 24 hours in ABS.

* when doing lot of editing on a very long mono track recording.

This mode is especially useful to check the data stored in the virtual tracks as the data

transferred to virtual tracks cannot be seen.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “NOs Of Event?”.

The “?” display will start flashing.

3. Press the EXECUTE/YES key.

The display will show the actual event number of track one.

SETUP

Displayed a current

Event Number

44.1kHz

∞

4. By turning the JOG dial, the display will show the track numbers one after the other so that you

can check the event number on each track.

5. Press the EXIT/NO key or STOP button to quit the SETUP mode.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to

the normal time base display.

* For details on audio files and events, refer to "2. Audio File and Event" in "Before operating."

163

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-21. Current Drive Setting (“Drive Sel.?”)

The “Current Drive” here means the medium drive device, either the internal IDE or SCSI,

to be used in real time recording or playing back.

For example, you need to set this mode to “SCSI” if you want to directly record data on to

the external SCSI device at real time or enter a title in the song number/back up number

on the SCSI device.

This mode allows you to choose the current drive from either the internal IDE hard disk

which is installed in the D-160, or a SCSI device which is externally connected.

If you choose the SCSI device whose medium has not been formatted, the D-160 will

automatically recognize it as an “unformatted medium” and move on to the “Disk Format?”

menu in the SETUP mode.

Then, after completing the format process, the “SCSI” will be chosen as the current drive.

* Initial setting : IDE (internal hard disk)

* Available setting : IDE, SCSI

* The setting will go back to “IDE” when you turn the power to off.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Drive Sel.?”.

The “?” display will start flashing. The display will also show the current setting.

In the case of the initial setting, it will show “IDE”.

3. Press the EXECUTE/YES key.

The current setting will start flashing which indicates it is ready to change setting.

SETUP

44.1kHz

∞

4. With the JOG dial, choose either “IDE” or “SCSI” you want.

5. Press EXECUTE/YES key after choosing the setting you want.

The display will go back to the display of item 2.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key so

that you can correct the setting, choose some other SETUP mode or eventually return to

the normal time base display.

<Notes>

* When you are to choose “SCSI” as the current drive, the display will show “Initializing ....”

then, “No SCSI Device!” and go back to the display of Item 2 if the power of the externally

connected SCSI device is not turned ON, or if it is not connected properly. Similarly, the

display will show “No Disk!” if the SCSI device does not have a medium inserted correctly.

* To eject the medium from the SCSI device, press the EXIT/NO key while holding down the

STOP button with the normal time base display.

164

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-22. Loading Song Data (“Load PGM?”)

Prior to loading externally saved song data back on to the D-160 internal hard disk drive,

this mode allows you to choose which DAT, adat or SCSI port will be used.

* See page "102" “Saving/Loading Song Data” for details of Loading Song Data.

* Available setting : adat, DAT, SCSI

* Available program : P1 ~ P99 or ALL (In the case of SCSI only)

* You can load one program or all the programs (in the case of SCSI only).

1. Press the DISP SEL key and choose the flashing SETUP mode on the display.

Then, press the EXECUTE/YES key. The SETUP display will stop flashing.

2. With the JOG dial, choose “Load PGM?”.

The “?” display will start flashing.

3. Press the EXECUTE/YES key.

The display will show “LOAD”.

The display will also show the current setting. In the case of initial setting, it will show “DAT”.

SETUP

44.1kHz

∞

LOAD

4. With the JOG dial, choose which type digital signal you want to use to load song data.

If you choose “adat”, the song data will be loaded via adat digital signal.

If you choose “DAT”, the song data will be loaded via SPDIF digital signal.

If you choose “SCSI”, the song data will be loaded via SCSI.

Load from “DAT”

5-a. Choose DAT with the JOG dial and press the EXECUTE/YES key.

The display will show “LOAD” and be flashing “SURE?”. The display will also start flashing the

currently chosen load target program number on the internal hard disk drive, which you are

loading the song data back on to.

6-a. With the JOG dial, choose the program number onto which you want to load on to.

You can choose any program available on the internal IDE drive to load song data on to.

If you want to load the data onto a new program rather than the program already available,

choose “New PGM” at this stage.

7-a. Press the EXECUTE/YES key. The display will show “LOAD” .

The display will also start to show the menu from which you can choose the tracks you want to

load on to. Choose the setting with the JOG dial.

The available loading track settings are ;

1-8, 1-16, 1-24, 9-16, 9-24, 17-24. We recommend you choose the loading tracks in the same

way as when you saved the data.

8-a. Press the EXECUTE/YES key after you have chosen the tracks you want.

The display will start flashing “SURE?”.

9-a. Press the EXECUTE/ YES key once again.

The display will show “Play DAT!”. This means the D-160 is asking you to start playing back the

DAT machine connected to the D-160, which has a tape recorded with the song data.

10-a. Start playing back the DAT.

The display will start showing “REMAIN”.

In few seconds, the D-160 will recognizes the pilot signal from the DAT. The display will then

start showing the program number you are loading the data to and the count down time display

indicating how long the load process is going take. The D-160 has now started loading the data.

The actual load process starts at the moment the display starts showing the count down time.

Loading from DAT is done via using a pair of stereo signals one after the other, e.g. 1-2 then 3-4

then....23-24. While loading, the D-160 will display track 1 and 2 indicators flashing with their

level meters moving.

165

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

11-a. When the D-160 has successfully loaded song data, “COMPLETED!” will be displayed.

Press the EXIT/NO key to cancel the message and return to the normal time base display.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key.

If you press these keys after you have started the loading process at Item 10, only the data

that has already been loaded will be effective.

The data that has not been loaded yet will be void.

Load from “adat”

5-b. Choose “adat” with the JOG dial and press the EXECUTE/YES key.

The display will show “LOAD” and flashing “SURE?”. The display will also start to flash the

currently chosen load target program number on the internal hard disk drive, which you are

loading the song data back to.

6-b. With the JOG dial, choose the program number which you want to load on on to.

You can choose any program available on the internal IDE drive to load song data to.

If you want to load the data onto a new program rather than the program already available,

choose “New PGM” at this stage.

7-b. Press the EXECUTE/YES key. The display will show “LOAD” .

The display will also start showing the menu from which you can choose the tracks you want to

load on to. Choose the setting with the JOG dial.

The available loading track settings are ;

1-8, 1-16, 1-24, 9-16, 9-24, 17-24. We recommend you should choose the loading tracks in the

same way as when you saved the data.

8-b. Press the EXECUTE/YES key after you have chosen the tracks you want.

The display will start flashing “SURE?”.

9-b. Press the EXECUTE/ YES key once again.

The display will show “Play adat!”. This means the D-160 is asking you to start playing back the

adat machine connected to the D-160, which has a tape recorded with the song data.

10-b. Start playing back the adat.

The display will show “REMAIN”. For your information, you need to set the clock source of the

adat unit as INTERNAL when you play back the tape.

In a few seconds, the D-160 recognizes the pilot signal from the adat.

The display will then start showing the program number to loading to and the counting down

time display indicating how long the load process is going take. The D-160 has now started

loading the data. The actual load process is start at the moment the display starts showing

count down time.

Loading from adat is done via using an 8 track adat signal one after the other, e.g. 1-8 then 9-16

then 16-24. While loading, the D-160 will display track 1-8 indicators flashing with their level

meters moving.

11-b. When the D-160 has successfully loaded song data, “COMPLETED!” will be displayed.

Press the EXIT/NO key to cancel the message and return to the normal time base display.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key.

If you press these keys after you have started loading process at Item 10, only the data that

has been loaded will be effective. The data that has not been loaded yet will be void.

Load from “SCSI” (Song Data Load)

5-c. Choose “SCSI” with the JOG dial and press the EXECUTE/YES key.

The display will show “LOAD”. The display will also start to flash the currently chosen load

source song number saved on the SCSI drive, which you are loading the data from.

6-c. With the JOG dial, choose a song number you want to load.

You can choose any ONE or ALL of the programs (songs) available in the external SCSI drive to

load the data from.

7-c. Choose the song number with the JOG dial and press the EXECUTE/YES key.

The display will show “LOAD” and flash “SURE?”. The display will also start to flash the

currently chosen load target program number on the internal hard disk drive.

166

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

With the JOG dial, choose a program which you want to load the song data back on to. If you

choose a program which has no data, the display will show “0MB”. If you want to load the

data onto a new program rather than to the program already available, choose “New PGM”.

8-c. Press the EXECUTE/YES key after you have chosen the program number.

The D-160 will start loading the song data you have chosen in 6-c to the program number you

have chosen in 7-c.

When the D-160 has successfully loaded song data, “COMPLETED!” will be displayed.

Press the EXIT/NO key to cancel the message and return to the normal time base display.

Warning

Be careful that If you choose “ALL” in the loading song/program options and start

loading the data, all the prerecorded material stored in the internal hard disk will

be erased even though you have set the “Rec Protect” mode to ON in the SETUP

mode.

Load from “SCSI” (Back Up Data Load)

The example described here is loading back up data “B01” which is saved on to two SCSI

disks. Let’s assume the first disk (DISK 1) has already been inserted in the SCSI device.

5-d. Choose “SCSI” with the JOG dial and press the EXECUTE/YES key.

The display will show “LOAD”.

The D-160 will also show “B01[Title] D1” on the display, which means;

B01(flashing)

: back up number currently chosen on the loading source

: disk number 1

6-d. Press the EXECUTE/YES key once again.

The display will start flashing “SURE?”.

The display will also start flashing the currently chosen load target program number on the

internal hard disk drive. With the JOG dial, choose a program which you want to load the song

data back on to. If you choose a program which has no data, the display will also show “0MB”.

If you want to load the data to a new program rather than to the program already available,

choose “New PGM” at this stage.

7-d. Press the EXECUTE/YES key after you have chosen the program number.

The D-160 will start loading the back up data “B01” onto the program number you chose in 6-d.

When finishing loading data from the first disk, the D-160 will show “Insert Disk 2” and eject Disk

1 automatically.

8-d. Insert the second disk in the SCSI device.

The D-160 will automatically start loading from the second disk.

When the D-160 has successfully loaded the song data, “COMPLETED!” will be displayed.

Press the EXIT/NO key to cancel the message and return to the normal time base display.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key.

If you press these keys after you have started the loading process, only the data that has

already been loaded will be effective. The data that has not yet been loaded will be invalid.

167

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

2-23. Saving Song Data (“Save PGM?”)

Prior to saving song data onto the externally connected device, this mode allows you to

choose which DAT, adat or SCSI port will be used.

* See page "102" “Saving/Loading Song Data” for details of saving Song Data.

* Available setting : adat, DAT, SCSI

* Available program : P1 ~ P99 or ALL (In the case of SCSI only)

* You can load one program or all the programs (in the case of SCSI only).

1. Press the DISP SEL key and choose the flashing SETUP mode on the display. Then, press the

EXECUTE/YES key.

The SETUP display will stop flashing.

2. With the JOG dial, choose “Save PGM?”.

The “?” display will start flashing.

3. Press the EXECUTE/YES key.

The display will show “SAVE”. The display will also show the current setting.

SETUP

44.1kHz

SAVE

∞

4. With the JOG dial, choose which type digital signal you want to use to save song data.

If you choose “adat”, the song data will be saved via adat digital signal.

If you choose “DAT”, the song data will be saved via SPDIF digital signal.

If you choose “SCSI”, the song data will be saved via SCSI.

Save to “DAT”

5-a. Choose “DAT” with the JOG dial and press the EXECUTE/YES key.

The display will show “SAVE”. The display will also start flashing the current program number

on the internal hard disk drive, which you are saving the song data from.

6-a. With the JOG dial, choose the program number which you want to save.

You can choose any program available in the internal IDE drive to save the song data.

7-a. Press the EXECUTE/YES key after you have chosen the program.

The display will show “SAVE”. The display will also show the recorded program length “Length?

**m**s”. This length is limited up to 59 minutes 59 seconds.

If you want to save the full length of the recorded data, follow the procedure below.

However, you can also edit the song length to be saved, which means either increasing or decreasing

it, at this stage.

8-a. Press the EXECUTE/YES key once again. The display will show “SAVE”.

The display will also start to show the menu from which you can choose the tracks that you want

to save. Choose the setting with the JOG dial.

Available loading track settings are ;

1-8, 1-16, 1-24, 9-16, 9-24, 17-24.

9-a.Press the EXECUTE/YES key after you have chosen the tracks you want.

The display will start flashing “SURE?”.

The display will also show “Rec Start DAT!”. This means the D-160 is asking you to start recording

onto the DAT machine connected to the D-160, which has a tape you will record the song data on

to.

10-a. Start recording DAT first then press the EXECUTE/YES key afterwards.

The display will start showing “REMAIN”.

In few seconds, the display will start showing the count down time display indicating how long

the save process is going take. The D-160 has now started saving the data.

The actual save process starts at the moment the display starts showing the count down time.

Saving to DAT is done via using a pair of stereo signals one after the other, e.g. 1-2 then 3-4

then....23-24.

168

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

11-a. When the D-160 has finished saving the song data, it will display “COMPLETED!” and then

return to the normal time base display.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key.

If you press these keys after you have started the saving process in 8, only the data that

has already been saved will be effective. The data that has not been saved yet will be invalid.

Save to “adat”

5-b. Choose “adat” with the JOG dial and press the EXECUTE/YES key.

The display will show “SAVE”. The display will also start flashing the current program number

on the internal hard disk drive, which you are saving the song data from.

6-b. With the JOG dial, choose the program number which you want to save.

You can choose any program available on the internal IDE drive to save the song data.

7-b. Press the EXECUTE/YES key after you have chosen the program.

The display will show “SAVE”. The display will also show the recorded program length “Length?

**m**s”. This length is limited up to 59 minutes 59 seconds.

If you want to save the full length of the recorded data, follow the procedure below. However,

you can also edit the song length to be saved, which means either increasing or decreasing it, at

this stage.

8-b. Press the EXECUTE/YES key once again. The display will show “SAVE”.

The display will also start showing the menu from which you can choose the tracks you want to

save. Choose the setting with the JOG dial. Available loading track settings are ;

1-8, 1-16, 1-24, 9-16, 9-24, 17-24.

9-b. Press the EXECUTE/YES key after you have chosen the tracks you want.

The display will start flashing “SURE?”.

The display will also show “Rec Start adat!”. This means the D-160 is asking you to start recording

onto the adat machine connected to the D-160, which has a tape you will record with the song

data.

10-b. Start recording adat first then press the EXECUTE/YES key afterwards.

The display will start showing “REMAIN”.

In a few seconds, the display will start showing the count down time display indicating how

long the save process is going take. The D-160 has now started saving the data.

The actual save process starts at the moment the display starts showing the count down time.

Saving to adat is done via using an 8 track signal one after the other, e.g. 1-8 then 9-16 then17-

24.

11-b. When the D-160 has finished saving song data, it will display “COMPLETED!” and then return

to the normal time base display.

* Press either the STOP button or EXIT/NO key to return from the second step menu to the

first or to quit SETUP mode. The menu will go backwards each time you press either key.

If you press these keys after you have started the saving process in 10, only the data that

has already been saved will be effective. The data that has not been saved yet will be invalid.

Save to “SCSI” (Program by Program)

5-c. Choose “SCSI” with the JOG dial and press the EXECUTE/YES key.

The display will show “SAVE”. The display will also start flashing the current program number

on the internal hard disk drive, which you are saving the song data from, e.g. “P02[Title]”.

6-c. With the JOG dial, choose the program number which you want to save.

You can choose any program available in the internal IDE drive on which to save the song

data. (See next section if you want to save ALL the programs at once .)

As far as saving is concerned, there are two types of program available:

One is a type of program whose data can fit on only one disk and another is one that requires

more than two disks. The display will appear as follow.

* A program that displays only the program number. This type of program can be saved on one

disk, e.g. “P02 [Title]”.

169

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

* A program that displays the program number and the indicator “*D” after the program number.

This type of program requires more than two disks to save, e.g. “P03[Title]2D”. “2D” means it

needs two disks to save.

7-c. Press the EXECUTE/YES key after you have chosen the program you want. The display will

show “SAVE”.

* If you choose the program that can be saved using one disk only:

The display will show the current song number (S**) and its available memory size on the SCSI

disk, e.g. “S01[Title]0MB” with “SURE?” flashing.

This means you are saving song data whose number is 01 onto a SCSI disk which has 0MB, i.e.

nothing stored. Press the EXECUTE/YES key to proceed.

* If you choose the program that requires more than two disks to save:

The saving will start immediately after you have pressed the EXECUTE/YES key. For example, if

you choose the program containing “P01[Title]2D”, the display will show “P01>>B01-***MB”.

Then, by the time saving is in progress, “-***MB” will be counting down.

The “B01” here means that the data which is being saved to the SCSI device is so called back up

data and the allocated number as “01”.

When finishing saving data to the first disk, the D-160 will show “Insert Disk 2” and eject Disk 1

automatically.

When you insert the second disk in the SCSI device, the D-160 will continue saving the remaining

data with the same back up number.

When the D-160 has successfully saved song data, “COMPLETED!” will be displayed. Press the

EXIT/NO key to cancel the message and return to the normal time base display.

<Notes>

* Unlike saving to DAT or adat, saving song data to SCSI cannot stop in the middle of

saving.

* If you want to change the title of the song data you are saving to SCSI, use “2-20. Drive

Sel?” to switch over the current drive to “SCSI” and proceed with “2-4. Title Edit?” in the

SETUP mode.

* When you are choosing “Save All” or saving song data on more than two disks on the

SCSI device, if you try to save on a disk which already has some data recorded, the D-160

will ask you whether you want the D-160 to erase all the data completely, e.g. the display

will show “B01[Title]DEL” or “S01[Title]DEL” with “SURE ?” flashing.

Press the EXECUTE/YES key if you don’t mind the disk being overwritten. But, if you do,

press the EXIT/NO key or STOP button to quit the mode and insert the correct disk.

To eject the disk, press the EXIT/NO key while holding down the STOP button.

Save to “SCSI” (Save All)

5-d. Choose “SCSI” with the JOG dial and press the EXECUTE/YES key.

The display will show “SAVE”. The display will also start flashing the current program number

on the internal hard disk drive, which you are saving the song data from, e.g. “P02[Title]”.

6-d. With the JOG dial, choose “Save All”.

The display will show “Save All? (**/**)”, which indicates the numbers of programs you are

saving and the numbers of programs that the current SCSI disk can save. For example, if the

display shows “03/03”, this means that there are a total of three programs to be saved and all

three programs can be saved to the current disk. However, if the display shows “01/03”, this

means that there are a total of three programs to be saved but only one program can be saved.

Or if the display shows “00/03”, none of the available programs can be saved due to the shortage

of SCSI disk space. In this last case, even though you press the EXECUTE/YES key to try to save the

song data, the D-160 cannot proceed with saving and will display “Void Command!” as a warning

message.

Basically, it is not possible to use more than two disks for saving the data with the “Save All”

option, unlike the “Program by Program” option described in the previous section. Therefore,

you have to find a large enough disk or try to save the data program by program.

7-d. Press the EXECUTE/YES key. The display will show “SAVE”.

The data which is being saved is called Song Data with the “Save All” option rather than back up

data with the “Program by Program” option.

170

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's manual (SETUP mode)

So, P1 in the internal IDE drive will be saved as S1, P2 as S2, etc. All the programs will be saved in

the same way.

When the D-160 has finished saving song data, it will display “COMPLETED!” and then return to

the normal time base display.

2-24. Formatting IDE/SCSI disk (“Disk Format?”)

When you format or initialize the internal hard disk or externally connected SCSI device,

use this “Disk Format?” menu. If the formatting has been completed, all the recorded

song data will be wiped off completely and the hard disk setting will go back to the initial

factory setting. You need to format a brand new IDE hard disk or SCSI disk before you

start using them.

* See page "39" for details of the Removable Hard disk Cartridge and the replacing Hard disk.

* See page "108" for details of the Handling SCSI disk.

1. Press the DISP SEL key and choose the flashing SETUP mode on the display.

Then, press the EXECUTE/YES key. The SETUP display will stop flashing.

2. With the JOG dial, choose “Disk Format?”.

The “?” display will start flashing. The display will also show the current setting.

3. Press the EXECUTE/YES key.

The current setting will start flashing which indicates it is ready to change setting.

SETUP

FORMAT

44.1kHz

∞

4. With the JOG dial, choose the “IDE” or “SCSI” you want.

5. Press EXECUTE/YES key after choosing the setting you want.

The display will show the drive you have chosen. Also, the D-160 will ask you whether you want

to proceed with formatting by displaying the message “SURE?”.

* If you want to cancel the format, press the EXIT/NO key at this stage. If you proceed with

the operation described in step 6 below, you will not be able to stop formatting.

6. If you really want to format, press the EXECUTE/YES key.

If you have chosen “IDE”, the format process will start immediately. The display will start showing

“REMAIN” and the count down memory space display (MB) indicating how long the formatting

process is going take.

Warning

Once the formatting starts, there is no way to stop it. Even the EXIT/NO key or STOP

button won’t help you! If you don’t want to lose the recorded data, never press the

EXECUTE/YES key at this stage.

If you have chosen “SCSI”, the formatting process will still not start. But instead, the display will

show the Format Type which the D-160 has automatically measured on the externally connected

SCSI device.

We recommend you format the disk with this Format Type. However, you can also change the

Format Type with the JOG dial at this stage.

Press the EXECUTE/ YES key after you have chosen the Format type you want.

Now the format process on the SCSI will start.

7. When the format finishes, the display will show “COMPLETED!” in either case.

8. Press the STOP button or EXIT/NO key to quit the SETUP mode and return to the normal time

base display.

171

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

(

Digital Multitrack Recorder

)

Date:

MIDI Implementation Chart

Model D-160

Version : V1.00

Transmitted

Recognized

Remarks

Function................

Basic

Default

Channel

Changed

Default

Message

Altered

Mode

***********************

Note

Number :

True voice

Velocity

Note ON

Note OFF

After

Key's

Touch

Channel's

Pitch Bend

Control

Change

Program

Change :

True #

***********************

(rem. 1)

System Exclusive

(rem. 2)

System

: Clock

Real Time : Commands

(rem. 3)

: Local ON/OFF

Aux.

Mes-

: All Notes OFF

: Active Sense

: Reset

sag

Notes

rem. 1: MMC (Device ID=00 ~ 99, 127), MTC, Identity reply, FOSTEX Exclusive

rem. 2: MMC (Device ID=00 ~ 99, 127), MTC, Inquiry, FOSTEX Exclusive

rem. 3: START, STOP, CONTINUE

Mode 1: OMNI ON, POLY

Mode 3: OMNI OFF, POLY

Mode 2: OMNI ON, MONO

Mode 4: OMNI OFF, MONO

: Yes

: No

172

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

MMC Command List

Command List

Movement (Recorder)

01: STOP

STOP

PLAY

02: PLAY

03: DEFERRED PLAY

04: FAST FORWARD

05: REWIND

DEFERRED PLAY

F FWD

REWIND

06: RECORD STROBE

07: RECORD EXIT

09: PAUSE

REC

PUNCH OUT

STOP

40: WRITE

Refer to MMC Response/Information Field List

LOCATE to Setting Data

41: MASKED WRITE

42: READ

44: LOCATE

46: SEARCH

CUE/REVIEW (±1~60 times)

Refer to MMC Response/Information Field List

47: SHUTTLE

4C: MOVE

4D: ADD

4E: SUBTRACT

MMC Response/Information Field List

01: SELECTED TIME CODE

03: REQUESTED OFFSET

04: ACTUAL OFFSET

08: GP0

Command

READ/WRITE/MOVE/ADD/SUBTRACT

READ/WRITE

READ

READ/WRITE/MOVE/ADD/SUBTRACT

READ

09: GP1

0A: GP2

0B: GP3

0C: GP4

0D: GP5

0E: GP6

0F: GP7

48: MOTION CONTROL TALLY

4C: RECORD MODE

4E: TRACK RECORD STATUS

4F: TRACK RECORD READY

51: RECORD MONITOR

READ/WRITE

READ

READ/WRITE/MASKED WRITE

READ/WRITE

Inquiry Message List

IDENTITY REQUEST : F0, 7E, <channel>, 06, 01, F7

IDENTITY REPLY : F0, 7E, <channel>, 06, 02, 51, 01, 00, 0C, 00, **, **, **, **, F7

51: Fostex ID

01, 00 : Device family code

0C, 00 : Device family number D-160

**, **, **, ** : Software version

173

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Fostex MIDI System Exclusive Message Format for D-160

<Note>

Following protocol is effective only in equipment which will reply by -

Identity Reply=F0 7E<channel>06 02 51 01 00 0C 00 01 ** ** ** F7 (D-160)

against the Inquiry Message=F0 7E<channel>06 01.

Fostex System Exclusive Message

General Structure=F0 51<device id><sub id 1>(<data>)F7

* Numbers are all expressed in hexadecimal units.

Table: <sub id 1> (<data>)

Command or Model Set

Controller to D-160

Acknowledge or Status

D-160 to Controller

Loop on/off

12 22 (<on/off>)

Post locate

Auto rec

12 28 (<post locate mode>)

12 2D (<on/off>)

32 2D (<edit message>)

Lock enable

Lock mode

Copy clip

12 41 (<lock enable>)

12 42 (<lock mode>)

12 45 (<count><mmc track>)

12 46 (<count=01><repeat count>)

32 45 (<edit message>)

32 46 (<edit message>)

Copy paste

12 46 (<count><repeat count><mmc track>)

12 47 (<count><mmc track>)

12 49

Erase

32 47 (<edit message>)

Clipboard play

Undo

32 49 (<edit message><count><mmc track>)

32 4A (<edit message>)

32 4B (<edit message>)

12 4A

Redo

12 4B

Move clip

12 4D (<count><mmc track>)

12 4E (<count=01><repeat count>)

32 4D (<edit message>)

Move paste

32 4E (<edit message>)

12 4E (<count><repeat count><mmc track>)

12 4F (<channel><channel>)

Track exchange

32 4F (<edit message>)

32 50 (<edit message>)

33 3E (<edit message>)

33 3F (<edit message>)

All erase current PGM 12 50

Product new PGM 13 3E

Delete current PGM 13 3F

Digital in ch.

13 41 (<channel><channel>)

13 41 (<channel=7F><count=0>)

Adat in

13 41 (<channel=7F><count><mmc track>)

13 42 (<channel><channel>) * Refer to Note.

13 42 (<channel=7F><channel=0>)

13 43 (<program>)

Digital out ch.

Adat out

Program change

Click on/off

13 44 (<on/off>)

Resolution on/off 13 46 (<on/off>)

Midi Sync out

13 47 (<nidi sync>)

MTC offset mode

13 48 (<MTC offset mode>)

13 49 (<count=3><on/off><vari data>)

Vari pitch

13 49 (<count=1><on/off>)

14 01 (<signature map>)

14 02 (<tempo set map>)

Signature set

Tempo set

34 00 (<edit message>)

Tempo map all erase14 03

Preroll time set

Frame rate set

Fs rate set

14 04 (<mmc time>)

14 06 (<frame rate>)

14 07 (<fs rate>)

Time base set

14 08 (<time base>)

174

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Status Request

Status request command

Controller to D-160

Status reply

D-160 to controller

Loop op. status

Loop status

22 21

22 22

22 28

22 2D

22 41

22 42

22 45

32 21 (<Loop op. mode = 12>)

32 22 (<on/off>)

Post locate status

Auto rec status

Lock status

32 28 (<post locate status>)

32 2D (<edit message>)

32 41 (<lock status>)

Lock mode status

Copy clip status

32 42 (<lock mode>)

32 45 (<edit message=01 or =14>)

32 46 (<edit message=02><mmc time>)

Copy paste status 22 46

32 46 (<edit message=00>)

32 47 (<edit message=02><mmc time>)

Erase status

22 47

22 4D

32 47 (edit message=00>)

32 4D (<edit message=01 or =14>)

32 4E (<edit message=02><mmc time>)

Move clip status

Move paste status 22 4E

32 4E (<edit message=00>)

33 41 (<channel><channel>)

33 41 (<channel=7F><count><mmc track>)

33 42 (<channel><channel>)

33 42 (<channel=7F><channel=0>)

33 43 (<program>)

Digital in ch. st.

Adat in status

Digital out ch. st.

Adat out status

Program status

Click status

23 41

23 42

23 43

23 44

23 45

23 46

33 44 (<on/off>)

Level status

33 45 (<count=10><level data>)

33 46 (<on/off>)

resolution status

midi sync out status23 47

MTC offset mode status 23 48

33 47 (<midi sync>)

33 48 (<MTC offset mode>)

33 49 (<count=3><on/off><vari data>)

vari pitch status

23 49

signature map req. 24 01 (<event number>) 34 01 (<signature map>)

tempo set map req. 24 02 (<event number>) 34 02 (<tempo set map>)

preroll time req.

remain time req.

frame rate status

fs rate status

24 04

24 05

24 06

24 07

24 08

34 04 (<mmc time>)

34 05 (<mmc time>)

34 06 (<frame rate>)

34 07 (<fs rate>)

time base status

34 08 (<time base>)

<Note>

There is a limitation on specifying the <channel><channel> setting. For details,

refer to "Explanation on Command/Mode Set" mentioned in later pages.

175

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Edit point memory of this equipment is alloted to the response/information field

of 08~0F (GP0~GP7) as shown below.

GP7 however, will be used as the work memory for small adjusting of the

registered figure (Refer to Examples 4 and 5).

08 GP0 : locate memory

09 GP1 : clipboard in memory

0B GP3 : start memory

0A GP2 : clipboard out memory

0C GP4 : auto punch in memory

0E GP6 : end memory

0D GP5 : auto punch out memory

0F GP7 : work memory

[Example 1] <mmc time> is registered in the start memory (using the write command).

F0 7F <device ID> 06 <write = 40> <count> <GP3 = 0B> <mmc time> F7

[Example 2] Locate memory is recalled (using the read command).

F0 7F <device ID> 06 <read = 42> <count> <GP3 = 08> <mmc time> F7

[Example 3] On-the-fly registering in the punch in memory (using the move command).

F0 7F <device ID> 06 <move = 4C> <count> <destination = 0C (GP4) > <source =

selected time code = 01> F7

[Example 4] When + 1 frame is to be set in the punch in memory (using the add

command).

* Time figure to be added is pre-registered in GP7 (Set 00h 00m 00s 01f in GP7).

F0 7F <device ID> 06 <add = 4D> <count> <destination = 0C (GP4)> <source #1 = 01

(GP4)> <source #2 = 0F (GP7)> F7

[Example 5] When -1 frame is to be set in the punch in memory (using the subtract

command).

* Time figure to be subtracted is pre-registered in GP7 (Set 00h 00m 00s 01f in

GP7).

F0 7F <device ID> 06 <substract = 4E> <count> <destination = 0C (GP4)>

<source#1 = 0C (GP4)> <source #2 = 0F (GP7)>F7

176

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Data Type

12=stop

Indicates the next operating mode following locating to the start point (GP1) upon

arriving at the end point (GP6) by the play mode.

In D-160, 12=stop only is effective.

12=stop

15=play

Specifies operating mode in which D-160 should enter upon completing the

locate operation. Corresponds to the setting of AUTO PLAY ON ("15")/OFF ("12") on

the main unit.

<count>

01~7F

Specifies succeeding data byte numbers.

Complies to the MMC (MIDI MACHINE CONTROL) standard track bit map.

In D-160, you always need to specify three byte combinations of "r0", "r1" and "r2."

00 = no message

01 = completed (completion flag)

02 = active (execution flag)

02<mmc time> = Indicates unprocessed time by active (execution flag) and <mmc

time>.

02<count><mmc track> = Indicates source track by active (execution flag) and

<mmc track>. Used for clipboard play.

03 = cancel (execution stop)

05 = Indicates rehearsal (rehearsal mode of auto rec). Possible of undo.

06 = Indicates take (take mode of auto rec). Possible of undo.

10 = over value error

10 <mmc time> = Capacity shortage time is indicated by over value error (error by

capacity shortage) and <mmc time>. In copy paste, it indicates capacity shortage

time required for a minimum one time paste.

11 = Indicates in point error (incorrect in point).

12 = Indicates out point error (incorrect out point).

14 = Indicates void data (data necessary for paste does not exist).

18 = Indicates track select error (track necessary to execute copy/move or erase/cut

is not correctly setup).

19<repeat count> = Indicates repeat number error and repeat numbers executable

by <repeat count>.

1A = Indicates disable rec (record disable mode).

71 = Indicates on.

72 = Indicates off.

hr mn sc fr {ff/st} complies to the MMC standard time code.

70 = default

71 = on

72 = off

01~7F

Especially when executing commands such as paste, the number of pasting times to

be continuously repeated following the auto punch in point is specified.

1~18, 7F

Select recorder tracks 1~18. "00" in particular, is not specified (default setting). "7F"

indicates input/output of Adat optical. For details, refer to explanation on setting

the Command/Mode.

00 = lock disable, chase disable

01 = lock enable, chase enable

Corresponds to SLAVE ON ("01")/OFF ("00") in the main unit.

00 = lock disable, chase disable

01 = lock enable (unlocked), chase enable (unlocked)

11 = lock enable (locked), chase enable (locked)

01~63H

Indicates program numbers (P1~P99) on the main unit. However, D-160 can specify

only 01 (corresponds to P1)~63H (corresponds to P99).

40 = Free

42 = Vari

45 = SP DIF

46 = adat

Indicates the slave mode when this equipment is set to slave ON.

177

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

bar2, bar1, bar0, sign, sigd

bar2: The 100th digit of the bar figure is expressed in BCD.

bar1: The 10th digit of the bar figure is expressed in BCD.

bar0: The 1 digit of the bar figure is expressed in BCD.

sign: Numerator of the signature to be set is expressed in BCD.

sigd: Denominator of the signature to be set is expressed in BCD.

When specified as sign=00 and sigd=00, signature data of that bar position will be

deleted. Also, bar2=bar1=bar0=sign=sigd=00 indicates "no corresponding data"

(such as when a figure specified by <event number> do not exist at receiving the

signature map request).

bar2, bar1, bar0, beat, tmp2, tmp1, tmp0

bar2: The 100th digit of the bar figure is expressed in BCD.

bar1: The 10th digit of the bar figure is expressed in BCD.

bar0: The 1 digit of the bar figure is expressed in BCD.

beat: The beat figure is expressed in BCD.

tmp2: Numerator of the tempo to be set is expressed in BCD.

tmp1: Denominator of the tempo to be set is expressed in BCD.

tmp0: The 1 digit of the tempo is expressed in BCD.

When specified as tmp2=tmp1=tmp0=00, tempo data of that bar and meter position

will be deleted. Also, bar2=bar1=bar0=sign=sigd=00 indicates "no corresponding

data" (such as when a figure specified by <event number> do not exist at receiving

the signature map request).

When one data registered by <signature map> and <tempo set map> is declared as

one event, the number of events from head of the tune (the umpteenth event

counted from head of the tune) must be specified. <event number="00"> is the first

event.

00: Off

01: CLK (MIDI CLOCK)

02: MTC

This corresponds to "Midi Sync Out?" of the SETUP menu.

Will be composed of two bytes (Q, P).

Q: 0qqqqqqq (binary) -> <vari data> = "qqqqqqqppppppp" A 14 bit data of X0.1

P: 0qqqqqqq (binary)

attached with a minus symbol.

Vari-pitch must be specified, at +0.1% when MSB (q)=0 (Example: 0000000000001),

and at -0.1% when MSB (q)=1 (Example: 1111111111111).

00: 30nd

01: 29.97nd

02: 29.97df

03: 25

04: 24

05: 30df

Corresponds to selecting "Frame Rate?" of the SETUP menu.

00: 48kHz

01: 44.1kHz

Corresponds to selecting "Sample Rate?" of the SETUP menu.

00: ABS

01: Signature

Corresponds to selecting "MTC Offset Mode?" of the SETUP menu.

00: ABS

01: BAR BEAT

02: MTC

t1, t2 ...... tn

n: Indicates the track number.

tn: Indicates absolute 8 bits of the Audio 16 bit data.

178

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Explanation on the Command/Mode Set

12 22 (<on/off>): loop on/off command

The command for setting the "loop mode on/off" (=ON/OFF of AUTO RTN) of D-160.

Default figure of the loop operation mode is "12=stop" and this cannot be changed.

12 28 (<post locate mode>): post locate command

The command for setting the "post locate mode" (=ON/OFF of AUTO PLAY) of D-160.

It will stop after locating if "post locate mode=12." It will enter play after locating if "post

locate mode=15."

12 2D (<on/off>): auto rec command

The command for setting "auto rec mode on/off" (=ON/OFF of AUTO PUNCH) of D-160.

Upon receiving this command, D-160 will immediately reply the operating condition by

sending "32 2D (<edit message>)".

12 41 (<lock enable>): lock enable command

The command for setting "slave mode on/off" (setup menu) of D-160.

12 42 (<lock mode>): lock mode command

The command for setup of the slave mode (setup menu) when this equipment is set to

"slave mode on."

12 45 (<count><mmc track>) : copy clip command

When this command is received, D-160 will copy (multiple number of tracks can be

copied simultaneously) the sound data, as data for copy paste, from the pre-registered

clipboard-in point to the clipboard-out point in the track specified by <mmc track>.

With completion of copying the data into the clipboard, D-160 will immediately reply

with "32 45 (<edit message=01 (completed)>)".

If copy cannot be executed due to improper figures of the pre-registered clipboard in/

clipboard out points or incorrect track section, the corresponding <edit message> will be

returned.

12 46 (<count=01><repeat count>): copy paste command

12 46 (<count><repeat count><mmc track>): copy paste command

When this command is received, D-160 will paste the sound data which has been copied

into the clipboard, on the same track from the pre-registered auto punch in point as the

starting point for the number of time specified by <repeat count>.

However, if the sound data length in the clipboard is less than 10ms, the specifying the

<repeat count> will be limited to "01."

Also, by specifying <mmc track>, paste can be executed on other tracks in mono (in one

track units) or stereo units (in combinations of tracks 1&2, 3&4, 5&6.......15 & 16).

Since time corresponding to length of the copy clipped sound data is required to complete

the copy paste operation, D-160 immediately replies with "32 46(<edit message=02

(active)>)" after receiving the command.

Successively upon completing the paste operation, "32 46 (<edit message=01

(completed)>)" is transmitted.

If paste cannot be executed due to improper figures of the pre-registered auto punch in

point, insufficient disc capacity, no sound data in the clipboard, etc., the corresponding

<editmessage> will be replied.

12 47 (<count><mmc track>): erase command

When this command is received, D-160 will erase the data (writes in "0" data) in the

section from the pre-registered auto punch in point through auto punch out point in the

track specified by <mmc track>. Since time corresponding to length of the erase section

is required to complete the erase operation, D-160 will immediately reply by "32 47

179

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

(<edit message=02 (active)>)" after receiving the command.

After the completion of erase operation, "32 47 (<edit message=01 (completed)>)" will

be transmitted.

If erase cannot be executed due to improper figures of the pre-registered auto punch in

point/auto punch out point, incorrect track section, etc., the corresponding <edit message>

will be replied.

12 49: clipboard play command

When this command is received, D-160 will playback once from the head of the sound

data copied in the clipboard by the copy clip and move clip commands.

Immediately after receiving the command, D-160 will reply with "32 49 (<edit message=02

(active)><count><mmc track>)." The sound data track number is indicated by (mmc

track>.

Upon completion of playback, "32 49 (<edit message=01 (completed) is sent and clipboard

play is ended. If there is no sound data in the clipboard, "32 49 (<edit message=14 (void

data)>)" will be sent and clipboard play operation will be interrupted.

12 4A: undo command

Upon receiving this command, D-160 will revert to the condition prior to editing copy

paste,erase, move paste, cut, redo operation. With completion of undo operation, D-160

will reply with "32 4A (<edit message=01(completed)>)."

If D-160 is not possible to undo, "32 4A (<edit message=00 (no message)>)" will be

replied.

12 4B: redo command

When this command is received, D-160 will return to the condition prior to undo operation.

With completion of redo operation, D-160 will reply with "32 4B (<edit message=01

(completed)>)."

If D-160 is not possible to redo, "32 4B (<edit message=00 (no message)>)" will be replied.

12 4D (<count><mmc track>): move clip command

When this command is received, D-160 will copy (multiple tracks can be copied

simultaneously) the sound data from the pre-registered clipboard in point to the clipboard

out point, as data for move paste operation.

With completion copying the data into the clipboard, D-160 will immediately reply with

"32 4D (<edit message=01 (completed)>)."

If copy cannot be executed by the reason of pre-registered improper clipboard in/clipboard

out point figures or incorrect track section, etc., the corresponding <edit message> will

be replied.

12 4E (<count=01><repeat count>): move paste command

12 4E (<count><repeat count><mmc track>): move paste command

When this command is received, D-160 will paste the sound data which have been move

clipped in the clipboard, for the number of times specified by <repeat count> on the

same track from the pre-registered auto punch in point as the starting point.

At the same time, the move clipped original sound data will be erased (data "0" is written

in). However, when sound data length in the clipboard is less than 10ms, specifying

the <repeat count> will be limited to "01."

Also, by specifying the <mmc track>, paste operation can be executed on other tracks in

mono(one track unit) or stereo units (tracks 1&2, 3&4, 5&6....... 15&16).

Since time corresponding to length of the move clipped sound data is required to complete

the move paste operation, D-160 will immediately reply with "32 4E (<edit message=02

(active)>)" after receiving the command.

Following completion of the move paste operation, "32 4E (<edit message = 01

(completed)>)" will be sent.

180

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

If paste cannot be executed due to improper figures of the previously registered auto

punch in point, insufficient disc capacity, no sound data is in the clipboard, etc., the

corresponding <edit message> will be replied.

12 4F (<channel><channel>): track exchange command (Exclusive command for FDMS-3.)

When the D-160 receives this command, the track can be exchange between the specified

<channel><channel>. Especially, if the first <channel=0>, then exchange by grouping

will be executed between channel 1-8 and channel 17-24, and if the next byte <channel=0>,

then the exchange will be between channel 9-16 and channel 17-24.

If it cannot be executed for some reason, an error message will be sent back.

12 50: all erase current program command (Exclusive command for FDMS-3.)

When the D-160 receives this command, all audio of the current program will be erased

to return it to the initial state of compiling a new program.

As execution of all erase is completed in a comparatively short time, the D-160 will reply

with "32 50 (<edit message=01 (completed)>)" immediately after completion of exchange.

If it cannot be executed for some reason, an error message will be sent back.

13 3E: product new program command (Exclusive command for FDMS-3.)

When the D-160 receives this command, a new program is compiled and the current

program is transferred to the new program.

As compilation of the new program is comparatively short time, it is replied with "33 3E

(<edit message=01 (completed)>)" immediately upon completion of execution.

If it cannot be executed for some reason, an error message will be sent back.

13 3F: delete current program command (Exclusive command for FDMS-3.)

When the D-160 receives this command, the current program is deleted and succeeding

programs moved up and renumberd. If the deleted program is the only tune existing in

the track, a new program will be made automatically.

As this delete current program is executed in a comparatively short time, "33 3F (<edit

message=01 (completed)>)" will be sent back immediately upon completing the execution.

If it cannot be executed for some reason, an error message will be sent back.

13 41 (<channel><channel>): digital in ch.select command

The audio signal input from SPDIF digital in to assigned to the destination track specified

by <channel>. The first <channel> shown in the command is the SPDIF L channel input,

and the second <channel> the R channel input. "<channel=0> <channel =0>" indicates

the normal analog input.

13 41 (<channel=7F><count><mmc track>): Adat in select command

Channel = 7F indicates that it is Adat In.

Normally, it will be "<count=0>" and all channels will be inputs from Adat In.

If <count=0><mmc track> is indicates, then only the tracks selected will be Adat In inputs.

"<channel=0><channel=0>" indicates the normal analog input.

13 42 (<channel><channel>): digital out ch.select command

The source channel for digital out is selected.

Normally, the first <channel> shown will be the SPDIF L channel data, and the second

<channel> the SPDIF R channel output.

By FDMS-2 (D-80, DMT-8) in particular, the following five types only can be setup.

(<01><02>), (<03><04>), (<05><06>), (<07><08>), (<00><00>). (<00><00>) is the

default setting. By FDMS-3 (D-160), any channel within "1 ~ 16" can be selected.

13 42 (<channel=7F><channel=0>): Adat out select command

In a device which can be switched between SPDIF and Adat, if the first display is

<channel=7F>, then Adat Out can be setup.

181

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

13 43(<program>): program change command

The command for PROGRAM CHANGE of D-160. The present program number can be

changed to the figure indicated by <program>.

13 44 (<on/off>): click on/off command

The command for setting the metronome on/off of D-160. When ON is set, the

metronome signal will be fed to the track 16 output (analog output only) of D-160.

13 46 (<on/off>): Bar/Beat Resolution ON/OFF command

The command for ON/OFF of the bar/beat resolution function of this equipments' current

program.

13 47 (<midi sync>): Midi Sync Out command

The setup command for MIDI Sync Out mode of this equipments' current program.

13 48 (<MTC offset mode>): MTC offset mode command

The setup command for MTC offset mode of this equipments' current program.

13 49 (<count=3> <on/off> <vari data>): Vari pitch command

13 49 (<count=1> <on/off>): Vari pitch command

The command for setting this equipments' vari pitch ON/OFF and pitch data.

Control of ON/OFF only is possible at <count=1> and both ON/OFF and pitch data can be

set at <count=3>.

14 01 (<signature map>): Signature set command

The command for setting the meter of this equipment. If a new data is registered at the

bar position where a data exists, the former data will be written over. When this command

is received, this equipment will reply with "34 00 (<edit message>)." Upon completing

the registeration, <edit message> will reply with "01 (completed)," or with "10 (over

value error)" if registeration is attempted at a non-existing point or an erroneous figure

is used.

14 02 (<tempo set map>): Tempo set command

The command for tempo set of this equipment. If a new data is registered in a bar/meter

where data already exists, the former data will be written over. When this command is

received, this equipment will reply with "34 00 (<edit message>)." Upon completing the

registeration, <edit message> will reply with "01 (completed)," or with "10 (over value

error)" if registeration is attempted at a non-existing point or an erroneous figure is

used.

14 03 : Tempo map all erase command

When this command is received, this equipment will erase all meter and tempo data in

the current program and thus return it to the default state (meter=4/4, tempo: =120).

Also, when this command is received, this equipment will reply with "34 00 (<edit

message>)." Upon completing the registeration, <edit message> will reply with "01

(completed)," or with "10 (over value error)" if registeration is attempted at a non-existing

point or an erroneous figure is used.

14 04 (<mmc time>): Preroll time set command

The command for setting the current program preroll time at the figure indicated by

<mmc time>.

14 06 (<frame rate>): Frame rate set command

The command for setting the current program frame rate at the figure indicated by

<frame rate>.

182

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

14 07 (<fs rate>): Fs rate set command

The command for setting the current program fs (sampling frequency) at the figure

indicated by <fs rate>.

14 08 (<time base>): Time base set command

The command for setting the current program time base of this equipment to that indicated

by <time base>.

The Status Request Command

22 21: loop operation status request

The command inquiring the loop operation mode setup status.

D-160 will reply with "32 21 (<loop op.mode=12>)."

22 22: loop on/off status request

The command inquiring the loop on/off (=ON/OFF of AUTO RETURN) setup status.

D-160 will reply with "32 22 (<on/off>)."

22 28: post locate status request

The command inquiring the post locate mode (ON/OFF of AUTO PLAY) setup status.

D-160 will reply with "32 28 (<post locate mode>)".

22 2D: auto rec status request

The command inquiring the auto rec mode setup status and this is replied by "32 2D

(<edit message>)." Reply from D-160 against this status request will be either one of the

following:

<edit message> =05: Possible to undo rehearsal mode.

=06: Possible to undo take mode.

=72: off

22 41: lock status request

The command inquiring the slave on/off setup status and the lock status.

D-160 will reply with "32 41 (<lock status>)."

22 42 : lock mode status request

The command for inquiring the lock mode setup status and this is replied with "32 42

<lock mode>."

22 45: copy clip status request

The command inquiring the clipboard condition. If there is a copy paste data in the

clipboard, D-160 will reply with "32 45 (<edit message=01>)." If data in the clipboard is

for move paste or there is no valid data in it, it will reply will "32 45 (<edit message=14

(void data)>)."

22 46: copy paste status request

The command inquiring execution status of copy paste editing.

When this command is received, D-160 will reply with either "32 46 (<edit message=02>

<mmc time>)" or "32 46 (<edit message=00>)." <mmc time> indicates unprocessed time

until completion.

22 47: erase status request

The command inquiring execution status of erase.

When this command is received, D-160 will reply by either "32 47 (<edit message=02>

<mmc time>)" or "32 47 (<edit message=00>)." <mmc time> indicates unprocessed time

until completion.

183

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

22 4D: move clip status request

The command inquiring the clipboard status. If there is a move paste data on the clipboard,

D-160 will reply with "32 4D (<edit message=01>)." If data in the clipboard is for copy

paste or there is no valid data on it, "32 4D (<edit message=14 (void data)>)" will be

replied.

22 4E: move paste status request

The command inquiring the move paste execution status.

When this command is received, D-160 will reply with "32 4E (<edit message=02><mmc

time>)" or "32 4E (<edit message=00>)." <mmc time> indicates unprocessed time until

completion.

23 41: digital in channel status request

23 41: adat in channel status request

The command inquiring the digital in channel setup status.

When this command is received, D-160 will reply with "33 41 (<channel><channel>)" or

"33 41 (<channel=7F><count><mmc track>)."

23 42: digital out channel status request

23 42: adat out channel status request

The inquiring the digital out channel setup status.

When this command is received, D-160 will reply with "33 42 (<channel><channel>)" or

"33 42 (<channel=7F><channel=0>)."

23 43: program status request

The command inquiring the presently operating program number.

When this command is received, D-160 will reply with "33 43 (<program>)."

23 44: click on/off status request

The command inquiring the metronome on/off status of D-160.

When this command is received, D-160 will reply with "33 44 (<on/off>)."

23 45: level status request

The command inquiring the present output level data of the 1~16 tracks. In D-160 as the

level data is updated about every 40msec., inquiry in 40msec. units is effective.

When this command is received, D-160 will reply with "33 45 (<count=10><level data>)."

23 46: resolution status request

The command for inquiring the resolution on/off setup status.

When this command is received, this equipment replies with "33 46 <on/off>."

23 47: midi sync out status request

The command for inquiring on status of the midi sync out setup condition.

When this command is received, this equipment replies with "33 47 <midi sync>."

23 48: MTC offset mode status request

The command for inquiring the MTC offset mode setup status. When this command is

received, this equipment replies with "33 48 <MTC offset mode>."

23 49: vari pitch status request

The command for inquiring status of vari pitch on/off and vari pitch data. When this

command is received, this equipment replies with "33 49 (<count=3> <on/off> <vari

data>)."

184

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

24 01 (<event number>): signature map request

The command for inquiring the meter setup. Order number counting from the leading

tune must be specified in the event number (The first event is expressed as "event

number=00." When this command is received, this equipment replies with "34 01

(<signature map>)."

24 02 (<event number>): Tempo set map request

The command for inquiring tempo data. Order number from the leading tune must be

specified in the event number (The first event is expressed as "event number=00."

When this command is received, this equipment replies with "34 02 (<tempo set map>)."

24 04: preroll time status request

The command for inquiring the preroll time setup status.

When this command is received, this equipment replies with "34 04 (<mmc time>)."

24 05: remain time request

The command for inquiring the disk remaining time which is recordable.

When this command is received, this equipment replies with "34 05 (<mmc time>)."

24 06: frame rate status request

The command for inquiring the frame rate setup status.

When this command is received, this equipment replies with "34 06 (<frame rate>)."

24 07: fs rate status request

The command for inquiring the fs (sampling frequency) setup status.

When this command is received, this equipment replies with "34 07 (<fs rate>)."

24 08: time base status

The command for inquiring the setup status of the time base shown in the display.

When this command is received, this equipment replies with "3408 (<time base>)."

Explanation on the Status Reply

32 21 (<loop op.mode>): loop operation mode status repry

This is the reply against the "22 21" loop operation status request command.

<loop op.mode=12> is the only status data of D-160 and any other setting is not

permissible.

32 22 (<on/off>): loop on/off status reply

This is the reply against "22 22" loop on/off status request.

32 28 (<post locate mode>): post locate mode status reply

This is the reply against "22 28" post locate status request. <post locate mode=12 or 15>

is the only status data of D-160 and any other setting is not permissible.

32 2D (<edit message>): auto rec status reply

This is the reply against the "12 2D" auto rec command or the "22 2D" auto rec status

request.

32 41 (<lock status>): lock status repry

This is the reply against the "22 41" lock status request.

32 42 (<lock mode>): lock mode status reply

This the reply against the "22 42" lock mode status request.

185

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

32 45 (<edit message>): copy clip status reply

This is the reply against the "12 45" copy clip command or the "22 45" copy clip status

request.

32 46 (<edit message>): copy paste status reply

32 46 (<edit message><mmc time>): copy paste status reply

This is the reply against the "12 46" copy paste command or the "22 46" copy paste

status request. <mmc time> indicates the unprocessed time until completion of copy

paste editing.

32 47 (<edit message>): erase status reply

32 47 (<edit message><mmc time>): erase status reply

This is the reply against "12 47" erase command or "22 47" erase status request.

32 49 (<edit message><count><mmc track>): clipboard play status reply

This is the reply against the "12 49" clipboard play command. If there is no sound data

in the clipboard, "32 49"(<edit message=14 (void data)>)" will be replied. <mmc track>

indicates the sound data track number.

32 4A (<edit message>): undo status reply

This is the reply against the "12 4A" undo command. Either <edit message=01 (completed)

or <edit message=14 (void data)> will be replied.

32 4B (<edit message>): redo status reply

This is the reply against the "12 4B" redo command. Either <edit message=01 (completed)>

or <edit message=14 (void data)> will be replied.

32 4D (<edit message>): move clip status reply

This is the reply against the "12 4D" move clip command or "22 4D" move clip status

request.

32 4E (<edit message>): move paste status reply

32 4E (<edit message><mmc time>): move paste status reply

The reply against the "12 4E" move paste command or the "22 4E" move paste status

request. <mmc time> indicates the unprocessed time until completion of move paste

editing.

32 4F (<edit message>): track exchange status reply

This is the reply against the "12 4F" track exchange command.

33 3E (<edit message>): product new program status reply

This is the reply against the "13 3E" product new program command.

33 41 (<channel> <channel>): digital in channel status reply

33 41 (<channel=7F> <count> <mmc track>): adat in status reply

This is the reply against the "23 41" digital in ch. st. request.

The first <channel> indicates the track number assigned to the L channel of the digital

audio signal (S/P DIF) from the DATA IN connector, and the second <channel> the track

number assigned to the R channel. If digital in is set to "Adat," the reply for the first

<channel> will be 7F and then <count> <mmc track>, in this order.

In the <mmc track>, the track bit map which is the Adat input, is expressed by "1" (In this

equipment, the reply will all be "1", or in other words, all tracks will be collectively

converted to Adat inputs or analog inputs).

186

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

33 42 (<channel> <channel>): digital out channel status reply

33 42 (<channel=7F> <channel=00>): adat out status reply

This is the reply against the "23 42" digital out ch. st. request.

The first <channel> indicates the track number assigned to the L channel output of the

digital audio signal (S/P DIF) from the DATA OUT connector, and the second <channel>

the track number as signed to the R channel output. If digital out is set to "Adat," the

reply for the first <channel> will be 7F and that for the second <channel> will be 00.

33 43 (<program>): program status reply

This is the reply against the "23 43" program status request.

<program> indicates the presently operating program number.

33 44 (<on/off>): click status reply

This is the reply against the "23 44" click status request.

It indicates the on/off setting of the metronome function.

33 45 (<count=10><level data>): level status reply

This is the reply against the "23 45" level status request and it indicates the present track

1~16 output level data.

In D-160, as level data is updated 40msec., it will be effective if inquiry is made in 40msec.

units.

33 46 (<on/off>): bar/beat resolution status reply

This is the reply against "23 46" bar/beat resolution status request.

33 47 (<midi sync>): midi sync out status reply

This is the reply against "23 47" midi sync out status request.

33 48 (<MTC offset mode>): MTC offset mode status reply

This is the reply against "23 48" MTC offset mode status request.

33 49 (<count=3> <on/off> <vari data>): vari pitch status reply

This is the reply against "23 49" vari pitch status request and is indicating the vari pitch

function on/off and the present vari pitch setup figure.

34 01 (<signature map>): signature map status reply

This is the reply against "24 01" (<event number>) signature map request.

The signature map of the event indicated by the <event number> is replied.

If there is no event specified (Example: Such as when <event number=5> is requested

even though there is only 5 meters registered), it will be replied with all figures at 00 of

the <signature map>.

34 02 (<tempo set map>): tempo set map status reply

The reply against "24 02"(<event number>)tempo set map request.

Tempo set map of the event indicated by the <event number> is replied.

If there is no event specified (Example: Such as when <event number=20> is requested

although only 10 is setup for tempo), it will be replied with all figures at 00 of the

<signature map>.

34 04 (<mmc time>): preroll set map status reply

This is the reply against "34 04" preroll time status request and this is replied with the

presently set preroll time.

187

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

34 05 (<mmc time>): remain time reply

This is the reply against "24 05" remain time request, and is replied with the recordable

disc remaining time.

34 06 (<frame rate>): frame rate status reply

This is the reply against "24 06" frame rate status request, and is replied with the presently

set frame rate.

34 07 (<fs rate>): fs rate status reply

This is the reply against "24 07" fs rate status request, and is replied with the presently

set fs (sampling frequency).

34 08 (<time base>): time base status reply

This is the reply against "24 08" time base status request, and is replied with the presently

set time base (in the display).

188

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Maintenance

Cleaning the exterior

* For normal cleaning, use a soft dry cloth.

For stubborn dirt, moisten a cloth in diluted detergent, wring it out firmly, and wipe the

dirt off. Then polish with a dry cloth.

Never use solvents such as alcohol, thinner or benzene, since these will damage the

printing and finish of the exterior.

Specifications

Input/Output

INPUT (1 ~ 8)

Connector

: RCA pin jack (X 8)

Input impedance : 10kΩ or more

Input level

: -10dBV

OUTPUT (1 ~ 16)

Connector

: RCA pin jack (X 16)

: -10dBV

Load impedance : 10kΩ or more

Output level

DATA IN/OUT

Connector

Format

: Optical (X 4)

: (1) IEC 958 Part 2 (=S/P DIF)

: (2) Alesis Proprietry Multi Channel Optical Interface

(Either (1) or (2) is selected in the Setup mode.)

MIDI IN/OUT/THRU

Connector

: DIN 5PIN (X 3)

: MIDI standard

Format

SCSI

Connector

:D-sub 25 pin (X1)

PUNCH IN/OUT

Connector

: ø6mm Phone jack (X 1)

(An optional FOOT SW Model 8051 can be

connected.)

REMOTE

Connector

: D-sub 15PIN (X 1)

Recording/Reproducing

Recording medium

: 3.5 inch, hard disk x 1 (E-IDE type),

(Optional hard disk)

Recording format

Save/Load format

Sampling frequency

Quantization

: FDMS-3*

: FDIO-1 Ver.2**

: 44.1kHz/48kHz

: 16-bit linear (Non expanded)

A/D: 18-bit 64-time, over sampling, Delta-Sigma

D/A: 20-bit 128-time, over sampling, Delta-Sigma

189

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Recording time

: approx. 240 minutes (at Optional Model 9041/

44.1kHz/Mono track recording)

No. of recording track : 16 + 8 Additional tracks

Program No.

Crossfade

: maximum 99 tunes

: 10msec.

Recording/reproducing

frequency

: 20Hz ~ 20kHz

: 90dB

Dynamic range

General

Dimensions

: 482 (W) X 140.5 (H) X 381 (D) mm, 3U size

* Including highest protrusion.

Weight

: approx. 8.0kg (with REMOTE controller)

Power supply

: 120VAC 60Hz

: 230V~ 50/60Hz

Power consumption

: approx. 32W

* Specifications and appearance are subject to change without notice for product improvement.

* "Adat" and the

symbol are trademarks of Alesis Corporation.

* FDMS-3: Fostex Disk Management System-3.

* FDIO-1 Ver.2: Fostex Data In Out-1 Ver.2

190

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

INDEX

[A]

Erasing

96, 99, 101

Entering Setup mode

137

About copy rights

About damages

[F]

Auto play/Auto return key

Fast forward button

Auto punch mode ON/OFF key

Formatting the hard disk 39, 43, 171

Auto punch in key

Auto punch out key

Auto return start key

Auto return end key

Formatting a SCSI disk

Frame rate setting

109

151

[H]

[ I ]

ABS time display

Hold/Digit move key

ABS

32, 38

Hard disk operation LED 13, 23

Audio file

Hard disk recording

Hard disk

Additional track

Analog recording

Auto play mode

Auto return mode 70

Auto repeat mode 74

Auto punch in/out 76

Introduction

Input jack

Input monitor

Installing a hard disk

Inquiry message list

[B]

[C]

173

Basic connections

Backup

111

[ J ]

[ L]

Jog dial

Clipboard in key

Clipboard out key 15

Copy key 20

Connecting a digital mixer

Changing the stored the start/end point 73

Copy and Pasting 88

Copying 86

Copy and paste undo/redo

compatibility with D-90, D-80 ver2 etc. 116

Locate key

Load Error ! display

Lock/unlock key

Locate function

Loading the data

102, 106

[M]

Main features

Meter display

[D]

MIDI IN connector 24

MIDI OUT connector

MIDI THRU connector

Display section

Dust cap 8, 39

DISK REMAIN display

Disk Error ! display

MTC display

MTC 38

Mixdown

Moving

Disable REC ! display

Disconnect SCSI display

Default setting on the D-160

Deleting program 51

Move & pasting

Move & paste undo/redo 95

Digital recording

MIDI clock synchronization system

117

123

Display select key 17

DATA IN connector

DATA OUT connector

MTC synchronization system

120

Multitrack system by the slave mode

Multitrack system using a DMT-8 V2.0 133

Metronome function ON/OFF

148

[E]

MIDI SYNC OUT setting

MTC frame rate setting

MTC OFFSET time setting

MTC OFFSET MODE setting

MIDI device ID setting

MIDI implementation chart

MMC command list

150

Erase key

151

Execute/Yes key

Exit/No key

152

153

Event Over ! display

Error 35 display

Error 36 display

161

173

172

Event

Maintenance

189

Extention cable

Editing and storing the start/end point 72

191

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Slave mode setting

Slave mode type setting

154

155

[N]

Notes about power supply 6

Sampling Frequency setting

162

Notes on handling the hard disk 7

Specifications

189

Notes on the setup location

Notes on repair

Notes on using detachable controller

[T]

[U]

Timebase

No disk IDE display

Track swapping

142

Time signature setting

Tempo setting 145

143

[O]

[P]

Over ! display

Overdubbing

Undo key

Un Format ! display

Precautions

Undo/Redo of Auto Punch In/Out

Undo/Redo the paste operation 90, 95

Undo/Redo the erase operation 98, 100

80, 84

Paste key

Play button

Punch in/out jack 23

Power switch

Power cable

[V]

Vari pitch key

Panel A, B

Void data ! display 29

Void In Point ! display

Void Out Point ! display

Vari pitch function

Preset display

Program change

Ping-pong recording

Punch In/Out

28, 35, 50, 54

Punch In/Out recording using a foot switch 81

Punch In/Out rehearsal mode 78, 82

Punch In/Out take mode 79, 83

[W]

Warning message

Program title setting

Program delete

147

Preroll time setting 149

[R]

Record track select key

Redo key

Recall key

Record button

Rewind button

Repro monitor

Real track

REMAIN

Recording/playback

Record protect setting

156

[S]

Shift key

Store key

Shuttle dial 18

Stop button 21

SCSI connector

Switching the time base display 27

Select Track ! display

Setting a program

Setting a sampling rate

Storing memory data

52, 162

Setting the auto return start/end point 71

Storing the punch in/out point 76

Saving data

Song

102, 104, 108, 168

111

Slave mode

SETUP mode

123, 127, 130

137

192

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

Declaration of EC Directive

This equipment is compatible with the EMC Directive (89/336/EEC) -

Directive on approximation of member nation's ordinance concerning

the electromagnetic compatibility and with the Low Voltage Directive

(73/23/EEC) - Directive on approximation of member nation's

ordinance connecting electric equipment designed to be used within

the specified voltage range.

The Affect of Immunity on This Equipment

The affect of the European Specification EN50082-1 (coexistence of

electromagnetic waves - common immunity specification) on this equipment are

as shown below.

* In the electrical fast transient/burst requirements, radiate electromagnetic

field requirements and static electricity discharging environment, this could

be affected by generation of noise in some cases. The display content

could also differ from actual figures.

Please comply to the precautions below to make this equipment compatible with

European Specification EN50082-1 (coexistence of electromagnetic waves -

common immunity specification).

<NOTE>

Caps are installed on the rear panel MIDI IN/OUT/THRU and SCSI

connectors. The purpose of these caps are to prevent static electricity from

affecting this equipment. Do not remove these caps except when using the

MIDI IN/OUT/THRU and SCSI connectors.

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

FOSTEX DISTRIBUTORS LIST IN EUROPE

* Including non-EU countries.

* underlined: contracted distributors (as of May, 1997)

NAME: IEMKE ROOS AUDIO B. V.

ADD: Kuiperbergweg 20, 1101 AG Amsterdam, The

Netherlands

NAME: ATEC Audio-u. Videogeraete VertriebsgesmbH.

ADD: Im Winkel 5, A-2325 Velm, Austria

TEL: (+43) 2234-74004, FAX: (+43) 2234-74074

TEL: (+31) 20-697-2121

FAX: (+31) 20-697-4201

NAME: EML N. V.

NAME: Siv. Ing. Benum A/S

ADD: Bijvennestraat 1A, B3500 Hasselt, Belgium

TEL: (+32) 11-232355, FAX: (+32) 11-232172

ADD: P. O. Box 145 Vinderen, 0319 Oslo 3, Norway

TEL: (+47) 22-139900, FAX: (+47) 22-148259

NAME: SC Sound ApS

ADD: Malervej 2, DK-2630 Taastrup, Denmark

TEL: (+45) 4399-8877, FAX: (+45) 4399-8077

NAME: Caius - Tecnologias Audio e Musica, Lda.

ADD: Rua de Santa Catarina, 131 4000 Porto, Portugal

TEL: (+351) 2-2084456/325400

FAX: (+351) 2-314760

NAME: Noretron Audio

ADD: Tonttumuorinkuja 4, FIN-02200 Espoo, Finland

TEL: (+358) 0-5259330, FAX: (+358) 0-52593352

<SPAIN>

NAME: Multitracker, S. A.

ADD: C/Garcilaso No.9, Madrid 28010, Spain

TEL: (+34) 1-4470700, 1-4470898

FAX: (+34) 1-5930716

NAME: Musikengro

ADD: ZAC de Folliouses, B. P. 609, 01706 Les Echets,

France

TEL: (+33) 72 26 27 00, FAX: (+33) 72 26 27 01

NAME: TTS Tal & Ton Studioteknik AB

ADD: Gelbgjutarevagen 4, S-171 48 Solna, Sweden

TEL: (+46) 8-7340750, FAX: (+46) 8-824476

NAME: Studiosound & Music GmbH

ADD: Scheppe Gewissegasse 8, D-35039 Marburg,

Germany

NAME: Audio Bauer Pro AG

TEL: (+49) 6421-12071, FAX: (+49) 6421-15522

ADD: Bernerstrasse-Nord 182, CH-8064 Zurich,

Switzerland

NAME: Bon Studio S. A.

TEL: (+41) 1-4323230, FAX: (+41) 1-4326558

ADD: 6 Zaimi Street, Exarchia, 106.83 Athens, Greece

TEL: (+30) 1-3809605-8, 3302059

FAX: (+30) 1-3845755

<UK>

NAME: SCV London

ADD: 3A 6-24 Southgate Road, London N1 3JJ,

England, UK

TEL: (+44) 171-923-1892, FAX: (+44) 171-241-3644

NAME: I. D. elrf. electronic Ltd.

ADD: ARMULA38 108 REYKJAVIK ICELAND

TEL: (+354) 588 5010, FAX: (+354) 588 5011

<ITALY>

NAME: Recoton Italia Srl.

ADD:V. 1 Maggio, N 18, 40050 Quarto Inferiore, (BO)

Italy

TEL: (+39) 51-768576, FAX: (+39) 51-768336

194

Download from Www.Somanuals.com. All Manuals Search And Download.

D-160 Owner's Manual (MMC/FEX List/Maintenance/Specifications)

195

Download from Www.Somanuals.com. All Manuals Search And Download.

FOSTEX CORPORATION

3-2-35 Musashino, Akishima-shi, Tokyo, Japan 196-0021

FOSTEX CORPORATION OF AMERICA

15431, Blackburn Ave., Norwalk, CA 90650, U. S. A.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electro Voice Speaker System Sb122 User Manual
Ericsson Home Theater System RX8310 User Manual
Fisher Paykel Washer GWL15 US FP WH User Manual
Fujitsu Scanner 15C User Manual
Furman Sound Power Supply PS PRO II User Manual
Furman Sound Power Supply SPR 20 User Manual
Gateway Computer Monitor FPD2185W User Manual
GE Conference Phone 25202 User Manual
GE Monogram Refrigerator ZISS360NMSS User Manual
Giant Bicycle XTC 1 User Manual