Fluke TV Cables OC4USB User Manual

- Click on the "Port Settings" tab. Click on the "Advanced"  
button.  
- On the bottom left side pull down the bar and select COM 1,  
2, 3 or 4 (NOTE: Choose one that dos not say "in use" next  
to it). Click "OK".  
Using the Interface Cable  
PC Requirements  
- USB 1.1 (or higher) port on the PC.  
- Windows XP/2000/Me/98 Second Edition.  
®
OC4USB  
- Click "OK" again. Notice that the device will show up as  
being on the same COM port that it was before (i.e., COM5),  
but will show up on the new port if you close the Device  
Manager and open it again.  
Installing the USB-IR cable drivers  
- Log into an account with Administrator privileges (Windows  
XP or Windows 2000).  
Optical Cable for USB  
- Plug the USB cable into an USB port.  
- Close the Device Manager.  
- Windows will respond that it has "found new hardware", and  
the Windows Hardware Wizard dialog will appear.  
- Insert the CD-ROM with the USB drivers (Included with  
cable or on FlukeView CD-ROM).  
Instruction Sheet  
Limited Warranty & Limitation of Liability  
This Fluke product will be free from defects in material and  
workmanship for one year from the date of purchase. This  
warranty does not cover fuses, disposable batteries or  
damage from accident, neglect, misuse or abnormal  
conditions of operation or handling. Resellers are not  
authorized to extend any other warranty on Fluke’s behalf. To  
obtain service during the warranty period, contact your  
nearest Fluke Authorized Service Center to obtain return  
authorization information, then send the defective product to  
that Service Center with a description of the problem.  
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER  
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR  
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT  
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING  
FROM ANY CAUSE OR THEORY.  
- Click the "Next>" button on the Hardware Wizard dialog  
- The Hardware Wizard will find the drivers on the CD-ROM  
("Prolific USB-to-serial bridge" on Windows XP/2000, or  
"USB to Serial Port" on Windows 98SE/Me).  
Note: for Windows XP users, you may get a dialog box  
warning you that this driver "has not passed Windows Logo  
Testing". Just click the "Continue anyway" button.  
- The Hardware Wizard will finish, the USB-IR cable drivers  
have now been installed.  
- Your PC may need to reboot before the USB-IR cable can  
be used.  
Note on Windows XP/2000: if you attach the USB-IR cable to  
a different USB port on your PC, you will have to repeat the  
installation of the drivers.  
Specifications  
Type of interface:  
Optically isolated serial to USB adapter  
Baudrate: 57.6 k Baud max  
Determining the USB-IR Cable's COM port  
- Attach the cable to the PC.  
- Go to the Windows Control Panel.  
- Open the "System Properties" dialog box.  
- Open the Device Manager:  
On Windows 2000/XP, click on the "Hardware" tab of the  
"System Properties" dialog box and click on the "Device  
Manager" button,  
On Windows 98SE/Me, click the "Device Manager" tab.  
- On the "Device Manager" dialog box, look under the "Ports  
(COM & LPT)" tree.  
- The COM port associated with the USB-IR cable is listed  
there, as:  
Logic States:  
SPACE = 0, Light with wavelength 800 nm  
MARK =1, No light  
Since some states or countries do not allow the exclusion or  
limitation of an implied warranty or of incidental or  
consequential damages, this limitation of liability may not  
apply to you.  
Handshake method:  
XON/XOFF, Software handshake only  
Fluke Corporation  
P.O. Box 9090  
Everett WA 98206-9090  
USA.  
Fluke Industrial B.V.  
P.O. Box 90  
7600 AB Almelo  
The Netherlands  
Environmental  
Meets requirements of MIL-T-28800D Type III, Class 3.  
Temperature  
Operating: -20 °C to +55 °C  
Storage: -20 °C to +70 °C  
Service Centers  
To locate an authorized service center, visit us on the World  
Wide Web:  
Mechanical  
Cable length:  
Weight:  
1.65 m  
0.1 kg  
"Prolific USB-to-serial bridge" (Windows 2000/XP),  
"USB to Serial Port" (Windows 98 SE/Me).  
Changing the COM port #  
Some programs require COM 1, 2, 3 or 4 and the USB cable  
is often installed as COM 5 or higher. To change the assigned  
COM port number, do the following:  
- Open Device Manager.  
- On the "Device Manager" dialog box, look under the "Ports  
(COM & LPT)" tree.  
or call Fluke using any of the phone numbers listed below:  
+1-888-993-5853  
+31-40-2675-200  
+1-425-446-5500  
in USA and Canada  
in Europe  
from other countries  
Sep 2004  
© 2004 Fluke Corporation. All rights reserved.  
Printed in The Netherlands. All product names are trademarks of their  
respective companies  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eiki Projection Television LC XG400 User Manual
Field Controls Air Cleaner UV 12C User Manual
FujiFilm Camera Lens 2030526 User Manual
Furuno Marine RADAR FR 1510D User Manual
Furuno Marine Radio Fax 210 User Manual
Garland Gas Grill XE362S 2L User Manual
GE Answering Machine 15380380 User Manual
GE Monogram Oven ZET3038SH WH BH User Manual
Genicom Printer 140 TM User Manual
GE Washer Dryer WPRB9220 User Manual