|
Multimedia Projector
PLV-60HT
Owner's Manual
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANCES
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generated, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
GROUND
Should you be unable to insert the plug into the outlet, contact your electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
6
7
COMPUTER MODE
23
SELECTING INPUT SOURCE
SELECTING COMPUTER SYSTEM
23
23
24
24
25
27
PREPARATION
PC ADJUSTMENT
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
COMPATIBLE COMPUTER SPECIFICATIONS
NAME OF EACH PART OF PROJECTOR
7
8
8
9
10
10
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
POSITIONING PROJECTOR
ADJUSTABLE FEET
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
28
28
29
IMAGE LEVEL ADJUSTMENT
MOVING PROJECTOR
PICTURE SCREEN ADJUSTMENT
30
VIDEO MODE
31
CONNECTING PROJECTOR
11
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
31
32
33
33
34
TERMINALS OF PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
CONNECTING TO COMPUTER
11
12
13
IMAGE LEVEL ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
35
BEFORE OPERATION
14
TOP CONTROLS AND INDICATORS
OPERATION OF REMOTE CONTROL
OPERATING RANGE
14
SETTING
36
16
16
17
17
SETTING MENU
36
WIRED REMOTE CONTROL OPERATION
REMOTE CONTROL BATTERIES INSTALLATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
18
18
18
19
APPENDIX
38
MAINTENANCE
38
38
38
38
39
39
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING THE PROJECTION LENS
LAMP REPLACEMENT
BASIC OPERATION
20
LAMP REPLACE COUNTER
TURNING ON / OFF PROJECTOR
ADJUSTING SCREEN
ZOOM ADJUSTMENT
20
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
40
42
21
21
21
21
21
22
22
FOCUS ADJUSTMENT
LENS SHIFT ADJUSTMENT
KEYSTONE ADJUSTMENT
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
SOUND ADJUSTMENT
VOLUME ADJUSTMENT
MUTE SETTING
22
22
22
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of
use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal
display (LCD) technology.
● Compatibility
● Progressive Scan (for Video)
This projector widely accepts various video and
computer input signals including;
Progressive Scan function converts interlace video
signals into progressive scan signals and provide fine
picture quality.
● 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-
N color system can be connected.
● Digital Zoom (for Computer)
● Component Video
Component video signals, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i-
60, can be connected.
Digital Zoom function magnifies the image up to 16
times, allowing you to focus on crucial information at a
presentation.
● S-Video
S-Video signals, such as a S-VHS VCR output
signals, can be connected.
● Motor-driven Lens Shift
Projection Lens can be moved up and down with Motor-
driven Lens Shift function. This function makes it easy to
provide projected image where you want.
Zoom and Focus can be also adjusted with Motor-driven
operation.
● Computers
IBM-compatible and Macintosh computers up to
1280 x 1024 resolution.
● High Resolution Image
This projector provides 1366 x 768 dots resolution for
computer input and 800 horizontal TV lines. The
resolution from computer between XGA (1024 x 768)
and SXGA (1280 x 1024) is compressed into 1024 x 768
dots. This projector cannot display image of over 1280 x
1024 dots. When the resolution of your computer is over
than 1280 x 1024, reset computer output for lower
resolution.
● Keystone Correction
Positioning height of projector may result in distorted
images being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
● Power Management
Power Management function is provided to reduce power
consumption while the projector is not in use.
● Multi-Scan System
This Power Management function operates to turn
Projection Lamp off when the projector detects signal
interruption and any button is not pressed over 5
minutes. Projection Lamp is automatically turned on
again when the projector detects the signal or any
operation button is pressed.
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for complicated manual adjustment of frequency
and other settings.
This projector is shipped with this function ON.
● One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and the
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
● Multilanguage Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish or
Japanese.
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT
TOP CONTROLS
AND INDICATORS
PROJECTION LENS
INFRARED
REMOTE RECEIVERS
LENS COVER
SPEAKERS
BACK
EXHAUST VENTS
HOT AIR EXHAUSTED !
Air blown from Exhaust Vents is hot. When
using or installing projector, the following
precautions should be taken.
● Do not put any flammable object near these
vents.
● Keep the rear grills at least 3’(1m) away from
any object, especially heat-sensitive object.
● Do not touch this area, especially screws and
metallic parts. This area will become hot
while projector is used.
This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.
TERMINALS
AND CONNECTORS
POWER CORD CONNECTOR
MAIN ON / OFF SWITCH
BOTTOM
AIR INTAKE VENTS
(Side and Bottom)
This projector is equipped with Cooling
Fans for protection from overheating.
Pay attention to the following to ensure
proper ventilation and avoid a possible
risk of fire and malfunction.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
● Do not cover vent slots.
● Keep bottom clear of any object.
Obstructions may block cooling air.
LAMP COVER
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V
or 200-240 V AC. The projector automatically selects the
correct input voltage. It is designed to work with single-
phase power systems having a grounded neutral
conductor. To reduce the risk of electrical shock, do not
plug into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of the type of power supply being in use.
Connect projector with the peripheral equipment before
turning projector on. (Refer to pages 11 ~ 13 for
connection.)
MAIN ON / OFF SWITCH
Connect AC Power Cord (supplied) to
CAUTION
projector.
For safety, unplug the AC Power Cord when the
appliance is not used.
The AC outlet must be near this
equipment and must be easily
accessible.
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below. The proper AC power cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada
For Continental Europe
Ground
To the POWER CORD
CONNECTOR on the
projector.
To the AC Outlet.
(120 V AC)
To the AC Outlet.
(200 - 240 V AC)
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
POSITIONING THE PROJECTOR
This projector is designed to project on a flat projection surface and it can be focused from 4.43’ (1.35m) ~ 45.9’
(14.0m). Refer to the figure below to adjust the screen size.
RECOMMENDATION
Brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in
order to provide the best image.
45.9’ (14.0m)
34.1’ (10.4m)
400”
Max. Zoom
Min. Zoom
22.9’ (7.0m)
300”
231”
11.5’ (3.5m)
308”
200”
154”
4.43’ (1.35m)
100”
77”
40”
31”
40”
886 x 498 mm
100”
200”
300”
400”
Screen Size
2215 x 1245 mm 4430 x 2490 mm 6644 x 3736 mm 8860 x 4980 mm
Width x Height
LENS SHIFT ADJUSTMENT
Projection Lens can be moved up and down with Motor-driven Lens Shift function. This function makes it easy
to provide the projected image where you want. Refer to P 21 for operation.
Highest Lens Shift
Lowest Lens Shift
H3
H4
H1
H2
H1 : H2 = 10.9 : 1
H3 : H4 = 1 : 3.9
NOTE
Screen size and lens shift ratio on the above charts are standard values and they may change by positioning
conditions.
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating Adjustable Feet. Projection angle can be
adjusted to 9.0 degrees.
Lift the front of projector and pull Feet Lock Latches on
both sides of projector.
1
Release Feet Lock Latches to lock Adjustable Feet and
rotate Adjustable Feet to fine tune position and tilt.
2
To shorten Adjustable Feet, lift the front of projector and
pull and undo Feet Lock Latches.
3
Position and keystone distortion of the image can be
adjusted using Menu Operation. (Refer to P 21 and 36.)
FEET LOCK
LATCHES
ADJUSTABLE FEET
MOVING PROJECTOR
Use Carry Handle when moving projector.
When moving projector, replace Lens Cover and retract
Adjustable Feet to prevent damage to Projection Lens
and cabinet.
When this projector is not in use for an extended period,
put it into the case (Dust Cover) supplied with this
projector.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
● Do not drop or bump projector, otherwise damages or malfunctions may result.
● When carrying projector, use a suitable carrying case.
● Do not transport projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to projector. To transport projector through a courier or transport service, consult your
dealer for best way.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has INPUT TERMINALS and OUTPUT TERMINALS on its side for connecting computers and
video equipment. Refer to the figure on pages 11 to 13 and connect properly.
INPUT
INPUT
1
RGB
SERIAL PORT
R/C JACK
R
-
AUDIO
-
L(MONO)
2
S-VIDEO
G
B
R
H/V
V
R
-
AUDIO
-
L(MONO)
INPUT / OUTPUT
TERMINALS
VIDEO/Y C/Pb (Cb) Pr (Cr)
INPUT
3
AUDIO OUT
AUDIO
VIDEO/Y Pb (Cb) Pr (Cr)
R
-
AUDIO
-
L
RESET
EXT.SP(8Ω)
R
-
-
L
(MONO)
BNC JACKS
SERIAL PORT TERMINAL
R/C JACK
Connect computer or video output to
these jacks.
Connect composite video output to
VIDEO/Y, separate video outputs to
VIDEO/Y and C/Pb(Cb) or component
video outputs to VIDEO/Y, C/Pb(Cb) and
Pr(Cr). (Refer to P12, 13.)
When controlling this projector
by computer, connect your
computer to this terminal.
When using Remote Control Unit as
Wired Remote Control, Connect
Remote Control Unit to this jack with
Remote Control Cable (supplied).
(Refer to page 16, 17.)
S-VIDEO INPUT JACK
Connect S-VIDEO output
from video equipment to
this jack. (Refer to P12.)
AUDIO INPUT JACKS
Connect audio output from
computer or video equipment to
these jacks. (Refer to P12, 13.)
RGB TERMINAL
Connect computer output to
this terminal. (Refer to P13.)
INPUT 1
RGB
SERIAL PORT
R/C JACK
R
-
AUDIO
-
L(MONO)
INPUT 2
S-VIDEO
G
B
R
H/V
V
R
-
AUDIO
-
L(MONO)
VIDEO/Y
C/Pb (Cb) Pr (Cr)
INPUT 3
AUDIO OUT
AUDIO
VIDEO/Y Pb (Cb) Pr (Cr)
R
-
AUDIO
-
L
RESET
EXT.SP(8Ω)
R
-
-
L
(MONO)
VIDEO INPUT JACKS
RESET BUTTON
AUDIO OUTPUT JACKS
Connect video output to these This projector uses a micro processor to
jacks. control the unit. Occasionally, the micro
Connect composite video processor may malfunction and need to
output to VIDEO/Y or connect be reset. This can be done by pressing
component video outputs to RESET button with a pen, which will
VIDEO/Y, Pb(Cb) and Pr(Cr). shut down and restart the unit. Do not
Connect an external audio
amplifier to these jacks.
(Refer to P12, 13.)
EXTERNAL SPEAKER JACK
(Refer to P12.)
use RESET function excessively.
Connect an external speaker
system to this jack.
(Refer to P12, 13.)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection (● = Cables are not supplied with this projector.)
• Video Cable (RCA x 1)
NOTE :
• Video Cable (RCA x 3)●, (BNC x 1)●, (BNC x 2)●●or (BNC x 3)●
• S-VIDEO Cable
• Audio Cable (RCA x 2)
When connecting projector, AC Power Cords of
both projector and external equipment should be
disconnected from AC outlet.
• Speaker Cable (Mini x 1 (stereo)) ●
Component video output equipment.
(such as DVD player or
Video Source (example)
Video Cassette Recorder
Video Disc Player
high-definition TV source.)
Component Video
Output
Composite
Video Output
Separate
Video Output
Component Video
Output
S-VIDEO
Output
Audio Output
Video Cable
(RCA x 3) ●
Video
Cable
Video
Cable
Video Cable
(BNC x 2) ●
Video Cable
(BNC x 3) ●
S-VIDEO
Cable
Audio Cable
(RCA x 2)
(RCA x 1) (BNC x 1)●
R
L
Y Pb/Cb Pr/Cr
VIDEO
VIDEO
Y
C
Y Pb/Cb Pr/Cr
S-VIDEO
INPUT 1
RGB
SERIAL PORT
R/C JACK
R
-
AUDIO-L(MONO)
INPUT 2
S-VIDEO
G
B
R
H/V
V
R
-
AUDIO
-
L(MONO)
VIDEO/Y
C/Pb (Cb) Pr (Cr)
INPUT 3
AUDIO OUT
AUDIO
VIDEO/Y Pb (Cb) Pr (Cr)
R
-
AUDIO
-
L
RESET
EXT.SP(8Ω)
R
-
-
L
(MONO)
EXT. SP
R
L
Speaker Cable
Audio Cable ●
(Mini / stereo) ●
(RCA x 2)
Speaker (8Ω / 2W)
Audio Amplifier
External Audio
Equipment
Audio Speaker
(stereo)
Audio Amplifier
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection (● = Cables are not supplied with this projector.)
• VGA Cable (HDB 15 pin) ●
• Video Cable (BNC x 5) ●
NOTE :
When connecting the cable, AC Power Cords of
• MAC Adapter (in the case of connecting Macintosh computer) ●
• Audio Cables (RCA x 2) or (RCA x 1 - Mini Plug (mono)) ●
• Speaker Cable (Mini Plug (stereo)) ●
both projector and external equipment should be
disconnected from AC outlet. Turn projector and
peripheral equipment on before your computer is
switched on.
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor Output
Monitor Output
Audio Output
Mini Plug
MAC Adapter ●
Set the slide
switches accord-
ing to the chart
on page 43.
Video Cable
(BNC x 5) ●
Audio Cable
(RCA x 2)
Audio Cable
(RCA-Mini Plug) ●
RCA
VGA Cable
R
L
G
B
R
H/V
V
MONO (L)
INPUT 1
RGB
SERIAL PORT
R/C JACK
R
-
AUDIO
-
L(MONO)
RGB
INPUT 2
S-VIDEO
G
B
R
H/V
V
R
-
AUDIO
-
L(MONO)
Use either RGB Terminal or
G, B, R, H/V and V jacks.
VIDEO/Y
C/Pb (Cb) Pr (Cr)
INPUT 3
AUDIO OUT
AUDIO
VIDEO/Y Pb (Cb) Pr (Cr)
R
-
AUDIO
-
L
RESET
EXT.SP(8Ω)
R
-
-
L
(MONO)
EXT. SP
R
L
Speaker Cable
(Mini / stereo) ●
Audio Cable ●
(RCA x 2)
Speaker (8Ω / 2W)
Audio Amplifier
External Audio
Equipment
Audio Speaker
(stereo)
Audio Amplifier
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
TOP CONTROLS AND
INDICATORS
INDICATORS
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
READY INDICATOR
LAMP INDICATOR
This indicator turns to
yellow when the life of
Projection Lamp draws to
an end. (P39)
This indicator flashes red
when internal projector
temperature is too high.
(P38)
This indicator lights green
when projector is ready to
be turned on. And it
flashes green in Power
Management mode. (P37)
This indicator is dim when
projector is turned on. And
bright when projector is in
stand-by mode.
LAMP
REPLACE
LAMP
WARNING
TEMP.
READY
ON-OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROL
FOCUS BUTTONS
MENU BUTTON
POWER ON–OFF BUTTON
INPUT BUTTON
Used to adjust focus. (P21)
Used to select MENU Used to turn projector on Used to select input source
operation. (P18, 19)
or off. (P20)
among INPUT 1, 2 or 3.
(P23, 31)
VOLUME BUTTONS
ZOOM BUTTONS
Used to adjust volume.
(P22)
Used to adjust zoom. (P21)
ON-OFF
MENU
INPUT
ZOOM
FOCUS
LENS SHIFT VOLUME
SELECT
AUTO PC ADJ.
NORMAL
LENS SHIFT BUTTONS
Used to adjust lens shift.
(P21)
AUTO PC ADJ. BUTTON
POINT BUTTONS
SELECT BUTTON
NORMAL BUTTON
Used to operate Auto PC Used to move Pointer or to Used to execute the item
Used to reset to normal
picture adjustments preset
by the factory or to reset
screen adjustment in True
mode, Digital Zoom mode or
Keystone mode. (P21, 28,
30, 33)
Adjustment function. (P24)
adjust the item on On-Screen selected or to expand
MENU. And it is also used to image in Digital Zoom
pan image in Digital Zoom mode. (P30)
mode. (P30)
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
Remote Control Unit can be used as either Wired or Wireless.
WIRED REMOTE JACK
When using as Wired Remote
Control, connect Remote Control
Cable to this jack. (P17)
INPUT BUTTON
Used to select input source.
(P23, 31)
MUTE BUTTON
POWER ON-OFF BUTTON
Used to mute sound.(P22)
Used to turn projector on or off.
(P20)
MUTE
INPUT ON-OFF
VOLUME BUTTONS
ZOOM BUTTONS
VOLUME ZOOM
FOCUS
Used to adjust volume. (P22)
Used to adjust zoom. (P21)
FOCUS BUTTONS
D.ZOOM BUTTONS
AUTO PC ADJ. D.ZOOM FREEZE
Used to adjust focus. (P21)
Used to select Digital Zoom
mode and resize image. (P30)
FREEZE BUTTON
Used to freeze picture. (P22)
IMAGE
NO SHOW
KEYSTONE
LENS SHIFT
AUTO PC ADJ. BUTTON
NO SHOW BUTTON
Use to operate Auto PC
Adjustment function. (P24)
SELECT
Used to turn picture into black
image. (P22)
MENU
NORMAL
IMAGE BUTTON
KEYSTONE BUTTON
Use to select IMAGE level.
(P28, 33)
Used to correct keystone
distortion. (P21, 36)
LENS SHIFT BUTTON
POINT BUTTONS
Used to select LENS SHIFT
function. (P21)
Used to move Pointer or to
adjust the item on On-Screen
MENU. And it is also used to
pan image in Digital Zoom
mode. (P30)
MENU BUTTON
Used to select MENU operation.
(P18, 19)
NORMAL BUTTON
SELECT BUTTON
Used to reset to normal picture
adjustments preset by the
factory or to reset screen
adjustment in True mode, Digital
Zoom mode or Keystone mode.
(P21, 28, 30, 33)
Used to execute the item
selected or to expand image in
Digital Zoom mode. (P30)
OPERATING RANGE
Point Remote Control toward projector (Remote Receiver) whenever pressing the buttons. Maximum operating
range for Remote Control is about 16.4’ (5m) and 60° in front and rear of projector.
60°
16.4’ (5 m)
60°
16.4’ (5 m)
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
WIRED REMOTE CONTROL OPERATION
When using this Remote Control Unit as Wired Remote Control, Connect Remote Control Unit to R/C JACK with
Remote Control Cable (supplied). Batteries installation is required when using as Wired Remote Control Unit.
Remote Control Cable (supplied)
INPUT
1
R/C JACK
REMOTE CONTROL BATTERIES INSTALLATION
Remove the battery
compartment lid.
Slide 2 batteries into
the compartment.
Replace the compartment
lid.
1
2
3
OPEN
OPEN
Press the lid
downward
and slide it.
Slide the lid
upward.
Two AA size batteries
For correct polarity (+ and –), be sure
the battery terminals are in contact
with pins in the compartment.
To insure safe operation, please observe the following precautions :
● Use (2) AA, UM3 or R06 type alkaline batteries.
● Replace two batteries at the same time.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose Remote Control Unit to moisture, or heat.
● Do not drop Remote Control Unit.
● If batteries have leaked on Remote Control Unit, carefully wipe the case clean and load new
batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
REMOTE CONTROL
You can control and adjust this projector through ON-
SCREEN MENU. Refer to the following pages to operate
each adjustment on ON-SCREEN MENU.
POINT BUTTONS
LENS SHIFT
KEYSTONE
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
1 DISPLAY MENU
SELECT
Press MENU button to display ON-SCREEN MENU.
MENU
NORMAL
SELECT BUTTON
2 MOVING POINTER
Used to select the item.
Move the pointer (● see below) or adjust the value of item by
pressing POINT button(s) on Top Control or on Remote
Control Unit.
TOP CONTROL
● Pointer is the icon on ON-SCREEN MENU to select the
item. See the figures on the section "FLOW OF ON-
SCREEN MENU OPERATION" below.
MENU
INPUT
SELECT BUTTON
Used to select the item.
L
SELECT
3 SELECT ITEM
Select the item by pressing SELECT button.
POINT BUTTONS
AUTO PC ADJ.
NORMAL
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
MENU ICON
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU
(MENU BAR). A red frame is POINTER.
1
POINTER
(red frame)
POINTER (red frame)
Select item to be adjusted
Press POINT DOWN button to
move POINTER.
Move POINTER (red frame) to MENU ICON that you
2
want to select by pressing POINT RIGHT / LEFT
buttons.
ITEM
Control and adjust through ON-SCREEN MENU
Press POINT DOWN button and move POINTER (red
frame or red arrow) to ITEM that you want to adjust, and
then press SELECT button to show Item Data.
SELECT
BUTTON
3
Adjust ITEM DATA by pressing POINT buttons.
Refer to the following pages for details of respective
adjustments.
4
ITEM DATA
Press POINT LEFT/RIGHT
buttons to adjust the value.
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press MENU BUTTON for PC input source.
INPUT MENU
IMAGE SELECT MENU
SETTING MENU
Used to select
input source
among INPUT 1,
2, or 3.
Used to select image
level among
Standard, Real or
Image 1 ~ 4.
Used to change settings
of projector and reset
Lamp Replace Counter.
(Refer to P36, 37)
SYSTEM MENU
Used to select
computer system.
(Refer to P23, 24)
(Refer to P23)
(Refer to P28)
GUIDE WINDOW
PC ADJUST MENU
IMAGE ADJUST MENU
SCREEN MENU
Shows selected
item of ON-
SCREEN MENU.
Used to adjust
parameters to
match with input
signal format.
Used to adjust
computer image.
[Contrast / Brightness /
White Balance (R/G/B)
/ Gamma]
Used to adjust
size of image.
(Refer to P30)
(Refer to P24-26)
(Refer to P29)
FOR VIDEO SOURCE
Press MENU BUTTON for VIDEO input source.
INPUT MENU
IMAGE SELECT MENU
SCREEN MENU
Used to select input
source among INPUT 1,
2, or 3, and to select
video source.
Used to select image
level among
Standard, Cinema or
Image 1 ~ 4.
Used to set size of
image to Full,
Zoom, Normal or
Wide zoom.
(Refer to P31)
(Refer to P33)
(Refer to P35)
SYSTEM MENU
IMAGE ADJUST MENU
Same function as the
Computer Mode.
Same function as the
Computer Mode.
Used to select
system of selected
video source.
Used to adjust picture image.
[Contrast / Brightness / Color /
Tint / White balance / Sharpness /
Gamma / Noise Reduction /
Progressive] (Refer to P34)
(Refer to P32)
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
Complete the peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to "CONNECTING TO
PROJECTOR" on Pages 11~13 for connecting that equipment.)
1
2
Connect the projector's AC Power Cord into an AC outlet and
turn MAIN ON / OFF SWITCH to ON. LAMP Indicator lights
RED, and READY Indicator lights GREEN.
30
NOTE : When “On start” function is ON, this projector is turned
on automatically by switching MAIN ON / OFF SWITCH
on. (Refer to page 37.)
Preparation Display disappears after 30 seconds.
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON. LAMP Indicator dims, and Cooling Fans
start to operate. Preparation Display appears on a screen and
the count-down starts. The signal from the PC or Video source
appears after 30 seconds.
3
TURNING OFF THE PROJECTOR
Press POWER ON-OFF button on Top Control or on Remote
Control Unit, and the message "Power off?" appears on a
screen.
1
2
Press POWER ON-OFF button again to turn off projector. LAMP
Indicator lights bright and READY Indicator turns off. After
projector is turned off, Cooling Fans operate (for 90 seconds).
During this "Cooling Down" period, this appliance cannot be
turned on.
Power off?
Message disappears after 4 seconds.
When projector has cooled down, READY Indicator turns to
green again and you can turn projector on. After cooling down
completely, turn MAIN ON / OFF SWITCH to OFF and
disconnect AC Power Cord.
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU
TURN PROJECTOR ON, WAIT AT LEAST 5
MINUTES BEFORE TURNING IT OFF.
When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically.
Refer to “Power Management” on page 37.
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on
projector again.
When WARNING TEMP. Indicator continues to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF and disconnect the AC Power Cord from a AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)
4. Turn projector on again.
If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or
service center.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
Press ZOOM ●/● button(s) on Top Control or on Remote
Control Unit. The message “Zoom” is displayed.
1
2
Press ZOOM ● button or POINT UP button to make image
larger, and press ZOOM ● button or POINT DOWN button to
make image smaller.
Zoom
Message disappears after 4 seconds.
FOCUS ADJUSTMENT
Press FOCUS ●/● button(s) on Top Control or on Remote
Control Unit. The message “Focus” is displayed.
1
2
Adjust focus of the image by pressing FOCUS ●/● button(s) or
POINT UP/DOWN button(s) .
Focus
Message disappears after 4 seconds.
LENS SHIFT ADJUSTMENT
Press LENS SHIFT ●/● button(s) on Top Control or LENS
SHIFT button on Remote Control Unit. The message “Lens
shift” is displayed.
1
2
Lens shift
Press LENS SHIFT ● button or POINT UP button to move
image up, and press LENS SHIFT ● button or POINT DOWN
button to move image down.
Refer to P9 for operating range.
Message disappears after 4 seconds.
KEYSTONE ADJUSTMENT
If image has keystone distortion, correct image with KEYSTONE adjustment.
Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING Menu (P36). The message “Keystone” is
displayed.
1
Correct keystone distortion by pressing POINT UP/DOWN
button(s). Press POINT UP button to reduce upper part of the
image, and press POINT DOWN button to reduce lower part of
the image.
2
Keystone
Message disappears after 4 seconds.
To reset Keystone adjustment, press NORMAL button.
Reduce the upper width with POINT UP button.
Reduce the lower width with POINT DOWN button.
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out the
image. To restore to normal, press NO SHOW button again or press
any other button.
No show
Message disappears after 4 seconds.
PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze the picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button.
SOUND ADJUSTMENT
Indicates the roughly level
of volume.
VOLUME ADJUSTMENT
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume. Volume dialog box appears on the screen for a
few seconds.
(+) button to increase volume, and (–) button decreasing.
MUTE SETTING
Press MUTE button to set
Mute function On or Off.
Press MUTE button on Remote Control Unit to cut off sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
The display disappears after 4 seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
SELECTING INPUT SOURCE
INPUT button
Input 1
DIRECT OPERATION
Choose either Input 1 or Input 2 by pressing INPUT button on Top
Control or on Remote Control Unit.
Input 2
Input 3
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
INPUT MENU
1
Press POINT DOWN button to move a red arrow pointer to
either Input 1 or Input 2 that you want to choose and then press
SELECT button.
When choosing Input 2, Source Select Menu will appear. Move
POINTER to RGB and then press SELECT button. (Input 2
accepts R, G, B, H/V and V computer signals (P 13).)
INPUT Menu icon
2
Move POINTER (red arrow)
to Input 1 or 2 and press
SELECT button.
INPUT 2
Source Select Menu (Input 2)
Move POINTER to RGB and
press SELECT button.
SELECTING COMPUTER SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 27). When selecting Computer, this projector automatically tunes
to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)
Note : Projector may display one of the following messages.
When projector cannot recognize connected signal
as PC system provided in this projector, Auto PC
Adjustment function operates to adjust projector
and the message “AUTO PC Adj.” is displayed on
SYSTEM icon. When image is not provided
properly, manual adjustment is required. (Refer to
P25 and 26.)
SYSTEM MENU
AUTO PC Adj.
SYSTEM Menu icon
Displays system being
selected.
There is no signal input from computer. Make
sure the connection of computer and projector is
set correctly.
No signal
(Refer to TROUBLESHOOTING on page 40.)
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
SELECT COMPUTER SYSTEM MANUALLY
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
SYSTEM MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SYSTEM icon.
1
SYSTEM Menu icon
Displays system being selected.
Press POINT DOWN button to move a red arrow pointer to the
The systems on this dialog box
can be selected.
2
system that you want to set, and then press
SELECT button.
Custom Mode (1~5) set in PC
ADJUST Menu. (P25, 26)
When this mark is displayed as
black, more computer system
modes will be available. Move
the arrow to this mark and then
press SELECT button, and the
other modes will be displayed.
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync., Total dots, and Picture Position to conform to
your computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
PC ADJUST MENU
1
2
Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button.
This Auto PC Adjustment can be executed by pressing AUTO
PC ADJ. button on Top Control or on Remote Control Unit.
PC ADJUST
Menu icon
Move a red frame pointer to AUTO PC
Adj. icon and press SELECT button.
Fine sync, Total dots and Picture Position of some computers
may not be fully adjusted with Auto PC Adjustment function.
When the image is not provided properly through this function,
manual adjustment is required. (Refer to page 25, 26.)
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in SYSTEM Menu (above). Refer to step
3 of MANUAL PC ADJUSTMENT section (P26).
NOTE : Auto PC Adjustment function cannot be operated when
“RGB,” “HDTV720p,” “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu (P23, 24).
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals from most personal computers currently distributed. However,
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-
Scan system of this projector. If this happens, projector cannot reproduce a proper image and the image may be recognized
as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall the setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu cannot be operated when “RGB” is selected on SYSTEM Menu (P23, 24).
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
PC ADJUST MENU
1
2
Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press POINT LEFT/RIGHT
button to adjust the value.
PC ADJUST
Menu icon
Move the red frame icon to the item and
press SELECT button.
Fine sync
Adjust the picture as necessary to eliminate flicker from the display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 255.)
Shows the status
(Stored/Free) of
Mode.
Total dots
Selected Mode
The number of total dots in one horizontal period. Press POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.
Horizontal
Adjust horizontal picture position. Press POINT LEFT/RIGHT
button(s) to adjust the position.
Press POINT LEFT/RIGHT
button to adjust the value.
Vertical
Adjust vertical picture position. Press POINT LEFT/RIGHT button(s)
to adjust the position.
Press SELECT button at this icon to
adjust “Total lines,” “Clamp,” “Display
area,” “Horiz. scale” or “Vert. scale” .
Current mode
Press SELECT button to show the information of computer selected.
Total lines
The number of the total horizontal lines. Press POINT LEFT/RIGHT
button(s) and adjust number to match your PC image.
Clamp
Adjusts clamp level. When the image has a dark bar(s), try this
adjustment.
Press SELECT button at
Current mode icon to show
the information of computer
connected.
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
Display area
Selects area displayed with this projector. Select the resolution at
the Display area dialog box.
Display area H
Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT button(s) and adjust number to match the
resolution of image.
Press SELECT button at
Display area icon and
the Display area dialog
box appears.
Display area V
Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT button(s) and adjust number to match the
resolution of image.
Horizontal scale
To store the adjustment data.
Adjustment of width of image. Press POINT LEFT/RIGHT button(s)
for adjustments.
This Mode has parameters being stored.
Vertical scale
Adjustment of height of image. Press POINT LEFT/RIGHT button(s)
for adjustments.
NOTE : Display area (H/V), Horizontal scale and Vertical scale
cannot be adjusted when “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu (P23, 24).
Fine sync and Total dots cannot be fully adjusted when
“HDTV1035i” or “HDTV1080i” is selected on SYSTEM Menu
(P23, 24).
Vacant Mode Shows values of “Fine sync,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Stored
3
Stored icon
To store adjustment parameters, move a red frame pointer to
Stored icon and then press SELECT button. Move a red arrow
pointer to any of Mode 1 to 5 that you want to store to and then
press SELECT button.
To clear the adjustment data.
Mode free
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button. Move
a red arrow pointer to the Mode that you want to clear and then
press SELECT button.
Other icons operates as follows.
Reset
Reset all adjust parameters on adjustment dialog box to previous
figure.
Close the dialog box.
Quit
Mode free icon
Closes PC ADJUST MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency mentioned below and
less than 180 MHz of Dot Clock.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.625
15.734
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.47
60.31
48.50
44.00
63.48
36.00
62.04
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
XGA 11
XGA 12
XGA 13
XGA 14
XGA15
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
61.00
35.522
46.90
47.00
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
75.00
80.00
45.00
33.75
33.75
75.70
86.96
(Interlace)
VGA 3
58.20
58.30
72.0
VGA 4
VGA 5
VGA 6
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
VGA 7
MAC LC13
MAC 13
RGB
640 x 480
––––––––
50
(Interlace)
60
––––––––
RGB
(Interlace)
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
86.00
(Interlace)
94.00
(Interlace)
SXGA 13 1280 x 1024
SXGA 14 1280 x 1024
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
60.01
72.00
66.00
SXGA 17
1152 x 900
86.70
XGA 2
SXGA 18 1280 x 1024
SXGA 19 1280 x 1024
SXGA 20 1280 x 1024
(Interlace)
XGA 3
60.18
85.024
75.08
75.08
60.00
XGA 4
XGA 5
MAC
1280 x 960
XGA 6
MAC
1280 x 1024
––––––––
XGA 7
HDTV720p
HDTV1035i
HDTV1080i
60.00
(Interlace)
60.00
(Interlace)
––––––––
––––––––
XGA 8
87.17
(Interlace)
XGA 9
XGA 10
77.07
NOTE : Specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing IMAGE button on the Remote Control Unit.
IMAGE button
Standard
Standard
Real
Normal picture level preset on this projector. This normal picture
level can also be selected by pressing NORMAL button.
Image 1
Image 2
Image 3
Image 4
Real
Picture level adjusted for the picture with fine tone.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P29).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press POINT DOWN button to move a red frame pointer to the
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Real
Move the red frame icon to the
level and press SELECT button.
Picture level adjusted for the picture with fine tone.
IMAGE 1~4
The level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P29).
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.
IMAGE ADJUST MENU
1
2
Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust. and then press SELECT button.
The level of each item is displayed. Adjust each level by
pressing POINT LEFT/RIGHT button(s).
IMAGE ADJUST
Menu icon
Move a red frame pointer to
the item to be selected and
then press SELECT button.
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Selected Image level
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
White balance (Red)
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Blue)
Stored icon
Press SELECT button at this icon to
store the adjustment.
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Stored
3
To store manually preset image, move a red frame pointer to
STORE icon and press SELECT button. Image Level Menu will
appear. Move a red frame pointer to the Image 1 to 4 where you
want to set and then press SELECT button.
Image Level Menu
Other icons operates as follows.
Move a red frame pointer to any of
Image 1 to 4 where you want to set
and then press SELECT button.
Reset
Reset all adjustment to previous figure.
Quit
Closes IMAGE MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER MODE
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
Press POINT DOWN button and move a red frame pointer to the
function that you want to select and then press SELECT button.
SCREEN Menu icon
Move the red frame to the function and
press SELECT button.
Normal
Provides image to fit the vertical size of the screen.
NOTE
● This SCREEN Menu cannot be operated when
“HDTV720p,” “HDTV1035i” or “HDTV1080i” is
selected on SYSTEM Menu (P23, 24).
Full
Provides image to fit the horizontal size of the screen.
● True and Digital Zoom cannot be selected when
“RGB” is selected on SYSTEM Menu (P23, 24).
True
Provides image in its original size. When the original image size is
larger than screen size (1366 x 768), this projector enters Digital
Zoom mode automatically. Image size can be set to Normal by
pressing NORMAL button.
● This projector cannot display any resolution higher
than 1280 X 1024. If your computer’s screen
resolution is higher than 1280 X 1024, reset the
resolution to the lower before connecting projector.
● The image data in other than XGA (1024 x 768) is
Digital Zoom
modified to fit the screen size in the initial mode.
● Panning function may not operate properly if the
computer system prepared on PC ADJUST Menu
is used.
Adjusts image size or pans image. In “Digital Zoom” mode, the ON-
SCREEN MENU disappears and the magnifying glass icon and the
message “D. Zoom” is displayed.
This projector also enters Digital Zoom mode by pressing the
D.ZOOM ●/● button on Remote Control Unit.
Refer to the following for operation.
Expand function
To expand the image size, press the D.ZOOM ● button or the
SELECT button. The image is magnified by degrees.
Compress function
To compress the image size, press the D.ZOOM ● button. The
size of image is reduced by degrees.
Panning function
To pan the image, press the POINT UP/DOWN/LEFT/RIGHT
buttons. Panning function can work only when the image is larger
than the screen size.
To return to screen size previously set, press NORMAL button.
To cancel Digital Zoom mode, press any button except D.ZOOM
●/●, SELECT, POINT, NORMAL or AUTO PC ADJ. button.
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
SELECTING INPUT SOURCE
INPUT button
Input 1
DIRECT OPERATION
Choose either Input 2 or Input 3 by pressing INPUT button on the Top
Control or on the Remote Control Unit.
If projector cannot reproduce proper video source, select correct input
source through MENU OPERATION (see below).
Input 2
Input 3
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
INPUT MENU
1
Press POINT DOWN button to move a red arrow pointer to
either Input 2 or Input 3 that you want to choose and then press
SELECT button. Source Select Menu appear.
2
Move the arrow to the Input
source and press SELECT
button.
Move the pointer to the source that you want to select and then
3
press SELECT button.
INPUT 2
INPUT 3
Source Select Menu (Input 2 / 3)
Move the arrow to the source and press SELECT
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
SELECTING VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SYSTEM Menu icon.
1
2
Press POINT DOWN button to move a red arrow pointer to the
system that you want to select and then press SELECT button.
AV SYSTEM MENU (VIDEO OR S-VIDEO)
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Move the pointer to the
system and press
SELECT button.
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
If pM3 T* S2 56.69 30p, .59* BT 9 6 3 -1 9 6 O -1 9 6 O apone Cuto
If projector cannot reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
VIDEO MODE
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing IMAGE button on the Remote
Control Unit.
IMAGE button
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
Standard
Normal picture level preset on this projector. This normal picture
level can also be selected by pressing NORMAL button.
Cinema
Picture level adjusted for the picture with fine tone.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P34).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press POINT DOWN button to move a red frame pointer to the
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Cinema
Move the red frame pointer to the
level and press SELECT button.
Picture level adjusted for the picture with fine tone.
IMAGE 1~4
The level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P34).
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
IMAGE ADJUST Menu icon.
IMAGE ADJUST MENU
1
2
Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust and then press SELECT button.
The level of each item is displayed. Adjust each level by
pressing POINT LEFT/RIGHT button(s).
IMAGE ADJUST
Menu icon
Move a red frame pointer to
the item to be selected and
then press SELECT button.
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Color
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
Tint
Press POINT LEFT button or POINT RIGHT button to obtain proper
color. (From 0 to 63.)
Press SELECT button at this icon to
display other items.
White balance (Red)
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
Sharpness
Press POINT LEFT button to soften the image, and POINT RIGHT
button to sharpen the image. (From 0 to 31.)
Gamma
Press SELECT button at this icon to
store the value.
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Noise reduction
Set “On” to reduce noise (rough parts) of the image.
Progressive
Set “On” to provide progressive scan mode.
NOTE : Tint cannot be adjusted when the video system is PAL,
SECAM, PAL-M or PAL-N.
Noise reduction cannot be selected when the input signal is
from Y, Pb/Cb, Pr/Cr jacks.
Progressive cannot be selected when “480p,” “575p” or
“720p” is selected on SYSTEM Menu (P32).
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO MODE
Stored
3
To store the adjustment data, move a red frame pointer to
Stored icon and press SELECT button. Image Level Menu will
appear. Move a red frame pointer to the Image Level 1 to 4 and
then press SELECT button.
Image Level Menu
Other icons operates as follows.
Move a red frame pointer to
the image icon to be set
and then press SELECT
button.
Reset
Reset all adjustment to previous figure.
Quit
Stored icon
Closes IMAGE MENU.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
Press POINT DOWN button and move a red frame pointer to the
function that you want to select and then press SELECT button.
SCREEN Menu icon
Move the red frame to the function and
Full
press SELECT button.
Provides image to fit width of screen by expanding image width
uniformly. This function can be used for providing a squeezed video
signal at wide video aspect ratio of 16 : 9.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select Full on this SCREEN Menu to provide better
quality.
NOTE : SCREEN Menu cannot be operated when
“720p,” “1035i,” “1080i-50” or “1080i-60” is
selected on SYSTEM Menu (P32).
Zoom
Provides image to fit screen size (16 : 9 aspect ratio) by expanding
image width and height uniformly. This function can be used for
providing a letter box mode picture (4 : 3 aspect picture with black
bar on top and bottom edges) at wide video aspect of 16 : 9.
Normal
Provides image at the normal video aspect ratio of 4 : 3.
Wide zoom
Provides image to fit width of screen by expanding both sides of
image. This function is suitable to provide a normal video signal (4 :
3 aspect ratio) at wide video aspect ratio of 16 : 9.
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red-frame pointer to
SETTING icon.
SETTING MENU
1
2
Press POINT DOWN button to move a red-frame pointer to the
Set the red frame
SETTING Menu icon
item that you want to set and then press
SELECT button.
pointer to the item
and press SELECT
button.
Setting dialog box appears.
Language
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish and Japanese.
Keystone
When the image is distorted vertically, select Keystone. ON-
SCREEN Menu disappears and the message “Keystone” is
displayed. Correct the Keystone distortion by pressing the POINT
UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page
21.
When selecting Language,
Language Menu appears.
Blue back
When this function is “On,” this projector will produce a blue image
instead of the video noise on the screen when the input source is
unplugged or turned off.
Display
This function decides whether to display the On-Screen Displays.
On ··· shows all the On-Screen Displays.
Off ···· sets the On-Screen Displays disappeared except;
● ON SCREEN MENU
● “Power off?” message
Move the pointer to the item
and then press POINT
LEFT/RIGHT button(s).
Logo
When this function is “On,” projector displays logo when starting up.
Ceiling
Ceiling function
When this function is “On,” picture is top / bottom and the left / right
reversed. This function is used to project the image from a ceiling
mounted projector.
Rear
When this function is “On,” picture is left / right reversed. This
function is used to project the image to a rear projection screen.
Rear function
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Power management
This function turns Projection Lamp off when projector detects signal
interruption and projector is not used for a certain period in order to
reduce power consumption and maintain the Lamp-life. (This
projector is shipped with this function ON.)
Time left until Lamp off.
Power Management function operates to turn Projection Lamp off
when the input signal is interrupted and projector is not operated
over 5 minutes. This function operates as follows;
1. When the signal is interrupted, “No signal” and the counting
down display appears (for 5 minutes).
2. When Projection Lamp turned off, READY Indicator turns off.
Cooling Fans operate and Projection Lamp is turned off for 90
seconds. (During this "Cooling Down" period, projector cannot
be turned on.)
3. When Projection Lamp has cooled down, READY Indicator
flashes and Projection Lamp can be turned on again (Power
Management mode).
In this Power Management mode, Projection Lamp is
automatically turned on when the input signal connected or
projector is operated with any button on the Top Control or on
the Remote Control Unit.
On start
When this function is “On,” projector is automatically turned on just
by switching MAIN ON / OFF SWITCH on.
Note ; Be sure to turn projector off properly (refer to the section
“TURNING OFF THE PROJECTOR” on page 20.). If
projector is turned off in the wrong steps, On Start function
does not operate properly.
Remote control
This projector has two different remote control codes; the factory-set
normal code (Code 1) and the secondary code (Code 2). This
switching function prevents the remote control operation mixture
(jam) when operating several projectors or video equipment together.
When operating projector in “Code 2,” both projector and Remote
Control must be switched to “Code 2.”
Move the pointer to the item
and then press POINT
LEFT/RIGHT button(s).
To change the code of Projector;
Set the Remote control in the SETTING MENU to “Code 2.”
To change the code of the Remote Control;
Press both MENU and NORMAL buttons on the Remote Control
Unit together for over 10 seconds.
After changing the code, make sure the Remote Control operates
properly.
To return to the normal code (Code 1), operate both projector and
Remote Control in the ways above again.
NOTE : When batteries of the Remote Control Unit is replaced, the
remote transmit code automatically returns to the normal
code (Code 1).
Lamp counter reset
This function is used to reset Lamp Replace Counter. When
replacing Projection Lamp, reset Lamp Replace Counter by using
this function. Refer to page 39 for operation.
Move the pointer to Lamp counter reset and then press
SELECT button. The message “Lamp replace counter
reset?” is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red when internal temperature of projector exceeds normal temperature. The Indicator
stops flashing when temperature of projector returns to normal. When WARNING TEMP. Indicator continues to flash, check
the items listed below.
Ventilation slots of projector may be blocked. In such an event, reposition the appliance so that Ventilation slots are
not obstructed.
1
Air Filters may be clogged with dust particles. Clean Air Filters by following the section AIR FILTER CARE AND
CLEANING below.
2
If WARNING TEMP. Indicator remains on after performing the above checks, Cooling Fans or Internal Circuits may be
malfunctioning. Contact a service personnel from an authorized dealer or service station.
3
AIR FILTER CARE AND CLEANING
Removable Air Filter prevents dust from accumulating on the surface of Projection Lens and the Projection Mirror. Should
Air Filter become clogged with dust particles, it will reduce Cooling Fans' effectiveness and may result in internal heat build
up and adversely affect the life of projector. Clean Air Filter following the steps below:
Turn the power off, and disconnect the AC Power Cord from an
AC outlet.
1
Turn projector upside down and remove Air Filter Cover by
pressing four latches sideways and pulling up. Remove three Air
Filters by pulling up the latches.
2
Clean Air Filters with brush or wash out the dust and particles.
Be sure to dry them out.
3
Replace Air Filters and Air Filter Cover properly. Make sure that
they are fully set.
4
Air Filter Cover
Press the latches
sideways and pull up.
CAUTION
Do not operate projector with Air Filters removed. Dust may
accumulate on the LCD Panel and the Mirror degrading
picture quality.
Do not put small parts into Air Intake Vents. It may result in
malfunction of projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when
operating projector. Usage in these environments may cause
poor image quality.
When using under dusty or smoky conditions, dust may accumulate
on the liquid crystal panel, Projection Lens, or optical elements inside
it. This condition may degrade the quality of the projected image.
When the above symptoms are noticed, contact your authorized
dealer or service station for proper cleaning.
Air Filters
Remove three Air Filters
by pulling up the latches.
CLEANING THE PROJECTION LENS
Follow these steps to clean the projection lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
1
Lightly wipe the cleaning cloth over the lens.
2
3
When projector is not in use, replace the lens cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT
When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT Indicator lights yellow. When the
image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required.
CAUTION
● For continued safety, replace with a lamp assembly of the same type.
● Allow projector to cool for at least 45 minutes before you open the lamp cover. The inside of projector can
become very hot.
● Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.
Follow these steps to replace the lamp assembly.
Turn off projector and disconnect AC plug. Allow projector to
cool for at least 45 minutes.
1
Remove a screw with a screwdriver and remove Lamp Cover.
2
Remove 2 screws and pull out Lamp Assembly by grasping
Handle.
3
LAMP COVER
Replace Lamp Assembly with a new one and tighten 2 screws.
Make sure that Lamp Assembly is set properly. Replace Lamp
Cover and tighten a screw.
4
LAMP
ASSEMBLY
Connect AC Power Cord to projector and turn on projector.
5
6
Reset Lamp Replace Counter (refer to the section “Lamp
Replace Counter” below).
NOTE : Do not reset Lamp Replace Counter when Projection
Lamp is not replaced.
HANDLE
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following information to the
dealer.
● Model No. of your projector : PLV-60HT
● Replacement Lamp Type No. : POA-LMP28
(Service Parts No. 610 285 4824)
LAMP REPLACE COUNTER
Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP
REPLACE Indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon (refer to page 36, 37).
1
Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press
message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SELECT button.
SELECT button. The
2
3
Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.
Do not reset Lamp Replace Counter except after Projection Lamp is replaced.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check the matters below once again.
1. Make sure you have connected projector to your equipment as described in the section "CONNECTING THE
PROJECTOR" on pages 11 ~ 13.
2. Check cable connection. Verify that all computer, video and power cords are properly connected.
3. Verify that all power is switched on.
4. If projector still does not produce an image, re-start the computer.
5. If the image sill does not appear, unplug projector from the computer and check the computer monitor's
display. The problem may be with your graphics controller rather than with projector. (When you reconnect
projector, remember to turn the computer and monitor off before you power up projector. Power the
equipment back on in order of : projector and computer.)
6. If the problem still exists, check the following chart.
Problem:
No power.
Try these Solutions
● Plug projector into the AC outlet.
● Be sure READY Indicator light is On.
● Wait 90 seconds after projector is turned OFF before turning projector back on.
NOTE : After pressing the power ON-OFF switch to OFF, make sure projector works as
follows:
1. The LAMP Indicator will light and the READY Indicator will turn off.
2. After 90 seconds, the READY Indicator will light green again and projector may
be turned on by pressing the power ON-OFF button.
● Check WARNING TEMP. Indicator. If this indicator flashes red, projector cannot be
turned on.
(See "TURNING ON/OFF THE PROJECTOR" section on page 20.)
● Check the Projection Lamp. (Refer to page 39.)
● Adjust the focus
Image is out of
focus.
● Make sure the projection screen is at least 4.43’ (1.35 m) from projector.
● Check the projection lens to see if it needs cleaning.
NOTE : Moving projector from a cool temperature location to a warm temperature location
may result in moisture condensation on the lens. In such an event, leave projector
OFF and wait until condensation disappears.
● Check Ceiling / Rear feature. (See “SETTING” section on page 36.)
Picture is Left/Right
reversed.
● Check Ceiling feature. (See “SETTING” section on page 36.)
Picture is
Top/Bottom
reversed.
● Check Display feature. (See “SETTING” section on page 36.)
Some displays are
not seen during the
Operation.
● Check the connection between the computer or video equipment and projector.
● When turning projector on, it takes about 30 seconds to display the image.
● Check the system that you select is corresponding with the computer or the video
equipment.
No image.
● Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).
● Check audio cable connection from audio input source.
● Adjust the audio source.
No sound.
● Press VOLUME (+) button.
● Press MUTE button.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solution
● Check the batteries.
● Make sure nothing is between the Remote Receiver and the Remote Control Unit.
● Make sure you are not too far from projector when using the Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Make sure the code of the Remote Control is set to conform to projector.
(See “SETTING” section on page 36, 37.)
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
after following all operating instructions,
If the problem still persists
purchased projector or the service center.
how to obtain service.
contact the sales dealer where you
Give the model number and explain the difficulty. We will advise you
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
12.44" x 6.46" x 18.9" (316mm x 164mm x 480mm)
20.3 lbs (9.2 kg)
(W x H x D)
Dimensions
Net Weight
1.35" TFT Active Matrix type, 3 panels
1366 x 768 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
3,147,264 (1366 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 31” to 400”
High Definition TV Signal
Scanning Frequency
(Diagonal)
Projection Image size
Horizontal Resolution
Projection Lens
800 TV lines
F 1.8 ~ 2.1 lens with f 48.4 mm ~ 62.8 mm with motor zoom, focus and shift
4.43’ ~ 45.9’ (1.35 m ~ 14.0 m)
Throw Distance
250 W
Projection Lamp
INPUT 1 : HDB 15 pin Type Terminal
Computer / AV Input Jacks
INPUT 2 : BNC Type Jacks (Video/Y, C/Pb(Cb), Pr(Cr)) / (G, B, R, H, V)
Mini DIN 4 pin Type Jack (S-Video)
INPUT 3 : RCA Type Jacks (Video/Y, Pb(Cb), Pr(Cr))
RCA Type Jacks (R and L(mono)) x 3
HDB 9 pin Type Terminal
Mini Jack
Audio Input Jacks (Input 1/2/3)
Serial Port Terminal
R/C Jack
RCA Type Jacks (R and L)
35 mm Mini Jack (8 Ω 2 W / stereo)
2.0 W RMS (stereo)
Audio Output Jacks
External Speaker Jack
Internal Audio Amp
Built-in Speakers
2 speakers, 1.57" x 2.76" (40mm x 70mm)
0˚ to 9.0˚
Feet Adjustment
Voltage and
Power Consumption
Operating Temperature
AC 100 ~ 120 V (4.4 A Max. Ampere), 50 / 60 Hz
AC 200 ~ 240 V (2.2 A Max. Ampere), 50 / 60 Hz
(
The U.S.A and Canada
)
(
Continental Europe
)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Storage Temperature
Power Source
Operating Range
Dimensions
:
:
:
:
AA, UM3 or R06 Type x 2
16.4’ (5m) / ±30˚
1.8” x 0.75” x 6.7” (45mm x 19mm x 170mm)
0.20 lbs (92 g) (including batteries)
Remote Control Transmitter
Net Weight
Owner’s Manual
Accessories
AC Power Cord
Wired/Wireless Remote Control Transmitter and Batteries
Video Cable (RCA x 1)
Audio Cable (RCA x 2)
S-Video Cable
Remote Control Cable
Dust Cover
Lens Cover
● The specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
CONFIGURATIONS OF TERMINALS
RGB TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of computer to this terminal with VGA Cable (not supplied). When connecting the
Macintosh computer, the MAC Adapter (not supplied) is required.
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
No Connect
Pin Configuration
10 Ground (Vert.sync.)
11 Sense 0
2
1
5
4
3
12 Sense 1
10
9
8
7
6
15
14
13
12
11
Ground (Horiz.sync.) 13 Horiz. sync.
Ground (Red)
Ground (Green)
Ground (Blue)
14 Vert. sync.
15 Reserved
SERIAL TERMINAL
Terminal : HDB9-PIN
Connect the serial port of computer to this terminal with Serial Cable (not supplied).
Pin Configuration
1
2
3
4
5
No Connect
R x D
6
7
8
9
No Connect
RTS
5
4
3
2
1
T x D
CTS
9
8
7
6
No Connect
Ground
No Connect
MAC ADAPTER (NOT SUPPLIED)
Set Slide Switches as shown in the table below depending on RESOLUTION MODE that you want to use before
you turn-on projector and computer.
Slide Switches (1 ~ 6)
1
2
3
4
5
6
ON
13” MODE (640 x 480)
16” MODE (832 x 624)
ON ON OFF OFF OFF OFF
OFF ON OFF ON OFF OFF
ON
DIP
1
2
3
4
5
6
19” MODE (1024 x 768) OFF ON ON OFF OFF OFF
21” MODE (1152 x 870) ON ON ON ON OFF OFF
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Japan
Part No. 610 294 7861 (1AA6P1P2944-- M4HAA)
SANYO Electric Co., Ltd
Download from Www.Somanuals.com. All Manuals Search And Download.
|