Fisher Price Toddler Furniture 79415 User Manual

TM  
My Little Desk Bed  
Model Number: 79415  
Instructions  
Please read these instructions and keep them for future reference.  
Adult assembly is required.  
My Little Desk Bed is recommended for children who are at  
least 15 months old and are ready to progress from a crib to a bed,  
including being able to get on and off a bed unassisted.  
Maximum weight: 50 lbs.  
Tools needed for assembly: Hammer and Two Phillips Screwdrivers.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Toddler Bed Assembly  
2
CAUTION  
Metal Tab  
Showing  
Please keep small parts and  
plastic bags out of children’s reach.  
Dispose of plastic bags properly.  
INCORRECT  
CORRECT  
1
• Check to be sure the crimped mattress tubes are inserted  
properly.  
• There is a metal tab on one side of the crimped end. Make  
sure the metal tab is not showing.  
Straight Side Rail  
Pull up firmly on the crimped mattress tubes to be  
sure they are securely in place.  
Crimped Mattress Tube  
• If the crimped mattress tubes can be removed from the  
1
straight side rail, re-read and repeat step  
.
3
Mattress Tube  
Crimped Mattress Tubes  
Mattress Tube  
Straight Side Rail  
Helpful Hint: The assembly of the crimped mattress  
tubes to the straight side rail is permanent. Once assembled  
properly, you will be unable to remove the crimped mattress  
tubes.  
Straight Side Rail  
• Place one of the straight side rails on a soft, flat surface.  
• Insert a crimped mattress tube into each slot in the straight  
side rail.  
• Insert the mattress tube into the hole in the straight side rail.  
• Tap the ends of the crimped mattress tubes with a hammer  
until they snap into place.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Toddler Bed Assembly  
6
4
Straight Side Rail  
Crimped Mattress Tube  
Mattress Tube  
Crimped Mattress Tubes  
Screw Holes  
Curved Ends  
Crimped Mattress Tubes  
• Position the other straight side rail so that the screw holes  
on each straight side rail are on the same side.  
Helpful Hint: The assembly of the crimped mattress tubes  
to the straight side rail is permanent. Once assembled prop-  
erly, you will be unable to remove the straight side rail.  
Mattress Tube  
• Repeat steps  
remaining crimped and regular mattress tubes.  
• Make sure the curved ends of the curved side rails are on  
the same side.  
Curved Side Rail  
to assemble the curved side rails and  
• Fit the slots and hole in the straight side rail onto the  
mattress tubes.  
• Push down on both ends of the straight side rail to be sure  
the crimped mattress tubes snap into place.  
-
1
5
5
INCORRECT  
CORRECT  
7
Curved Side Rail  
Straight Side Rail  
Metal Tab  
Showing  
• Check to be sure the crimped mattress tubes are inserted  
properly.  
• There is a metal tab on one side of the crimped end. Make  
sure the metal tab is not showing.  
Straight Side Rail  
Curved Side Rail  
Pull up firmly on the straight side rail to be sure the  
mattress tubes are securely in place.  
• If the straight side rail can be removed from the crimped  
• Place both metal frame assemblies on a flat surface.  
• Insert the straight side rails into the curved side rails, as  
shown.  
mattress tubes, re-read and repeat step  
.
4
4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Toddler Bed Assembly  
Mattress Retainer  
8
10  
Headboard  
®
Metal Frame  
Right Side Panel  
Left Side Panel  
#10 – 24 x 11/4" Screw  
Shown Actual Size  
• Stand the headboard assembly upright, as shown.  
• Push down on the top of the headboard to secure it to the  
right and left side panels.  
• Locate the holes in the metal frame, near the middle.  
Helpful Hint: If you are having difficulty securing the  
headboard to the left and right side panels, position the  
assembly against a wall (with the molded moon, sun  
and star toward the wall). Push down on the top of the  
headboard to secure it to the left and right side panels.  
• Position a mattress retainer so that the arrow is pointing  
up and is over the hole on the inside of the metal frame  
assembly.  
• Insert a barrel nut through the mattress retainer and into the  
inside of the metal frame.  
• Insert a 11/4" screw into the outside of the metal frame and  
hand tighten the hardware.  
11  
• While holding the barrel nut in place with a Phillips screw-  
driver, tighten the screw with the other Phillips screwdriver.  
Do not over-tighten.  
Metal  
Frame  
• Repeat this procedure to attach the other mattress retainer  
to the other side of the metal frame.  
9
Headboard  
Left Side Panel  
Straight End  
Groove  
Pegs  
Slots  
Right Side Panel  
• Position the headboard on a flat surface with the molded  
moon, sun and star facing up.  
• Position the right side panel with the R facing the  
headboard.  
Left Side Panel  
Right Side Panel  
Headboard  
• Fit the pegs on the headboard into the slots in the right  
side panel.  
• Turn the headboard assembly backward, as shown.  
• Position the metal frame with the straight ends downward,  
and the curved ends pointing forward, as shown.  
• Repeat this procedure to attach the left side panel to the  
headboard.  
• Insert the metal frame straight ends into the grooves in the  
left and right side panels.  
5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Toddler Bed Assembly  
12  
14  
Footboard  
Metal Frame  
F
i
sh  
er  
-P  
ri  
ce  
®
Metal Frame Curved End  
Groove  
• Fit the metal frame curved ends into the grooves in the  
footboard.  
15  
• Push down on the metal frame to completely insert it into  
the grooves in the left and right side panels.  
13  
F
is  
h
e
r
-P  
ri  
®
c
e
Screws  
Footboard  
• Insert four barrel nuts into the metal frame curved ends.  
• Insert four screws into the outside of the footboard and  
hand tighten the hardware.  
• While holding a barrel nut in place with a Phillips screw-  
driver, tighten the screw with the other Phillips screw-  
driver. Do not over-tighten. Repeat this procedure to tighten  
the other screws.  
Barrel Nuts  
Screws  
Left Side Panel  
• Insert two barrel nuts into the metal frame located on the  
inside of the left side panel, as shown.  
• Insert two screws into the outside of the left side panel and  
hand tighten the hardware.  
Toddler bed assembly is now complete.  
• While holding a barrel nut in place with a Phillips screwdriv-  
er, tighten the screw with the other Phillips screw-  
driver. Do not over-tighten. Repeat this procedure to tighten  
the other screw.  
• Repeat this step to secure the right side panel to the  
metal frame.  
• Turn the assembly right side up.  
6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Converting the Toddler  
Bed to a Desk  
Desk Assembly  
1
Left Side Panel  
Right Side Panel  
Pegs  
F
is  
h
e
r-  
P
r
®
ic  
e
Slots  
Desk  
• Position the desk on a flat surface with the molded moon,  
sun and star facing down.  
• Position the right side panel with the R facing the desk.  
• Fit the pegs on the desk into the slots in the right side  
panel.  
• The My Little Desk BedTM easily disassembles to convert to a  
desk.  
• Remove the barrel nuts and screws (eight of each) from the  
left side panel, right side panel and footboard.  
• Repeat this procedure to attach the left side panel to the  
desk.  
• Remove the headboard, left and right side panels and foot-  
board from the metal frame.  
IMPORTANT! Do not attempt to disassemble the metal  
frame. Please store the metal frame with barrel nuts  
and screws in a safe place for future use.  
2
Desk Assembly  
Desk Top  
(was  
Footboard)  
Desk (was  
Headboard  
Desk  
Right Side Panel  
Left Side Panel  
Right Side Panel  
Left Side Panel  
• Stand the desk assembly upright, as shown.  
• Push down on the top of the desk to secure it to the left  
and right side panels.  
Helpful Hint: Because you are assembling a desk, we have  
Helpful Hint: If you are having difficulty securing the desk  
to the left and right side panels, position the assembly  
against a wall (with the molded Fisher-Price logo toward  
the wall). Push down on the top of the desk to secure it to  
the left and right side panels.  
converted the names of some of the parts in this section.  
• The headboard is now the desk.  
• The footboard is now the desk top.  
7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Desk Assembly  
Care  
• Wash all parts with a mild cleaning agent and damp cloth.  
Do not use bleach. Rinse with clean water to remove  
residue.  
3
Desk Top  
• Periodically check My Little Desk BedTM for loose fasteners  
and tighten as needed.  
Groove  
Peg  
Groove  
Peg  
One (1) Year  
Limited Warranty  
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York  
14052, warrants that My Little Desk BedTM is free from all  
defects in material and workmanship when used under  
normal conditions for a period of one (1) year from the date  
of purchase.  
Should the product fail to perform properly, we will repair  
or replace it at our option, free of charge. Purchaser is respon-  
sible for shipping the product to Fisher-Price Consumer  
Affairs at the address indicated above and for all associated  
freight and insurance cost. Fisher-Price, Inc. will bear the  
cost of shipping the repaired or replaced item to you.This  
warranty is void if the owner repairs or modifies the product.  
This warranty excludes any other liability other than that  
expressly stated above including but not limited to any  
incidental or consequential damages.  
Desk  
• Position the desk top so that the grooved side is toward the  
desk.  
• Fit the pegs on the desk into the grooves in the desk top.  
4
Desk Top  
SOME STATES DO NOT ALLOW THE EXCLUSION OR  
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION  
MAY NOT APPLY TO YOU.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS  
AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS  
WHICH VARY FROM STATE TO STATE.  
If you have any questions about this product:  
In Canada, call 1-800-567-7724, or write to:Mattel/Fisher-Price,  
6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.  
In Great Britain, telephone 01734 770488.  
In Australia, call the Fisher-Price Australian Consumer Advisory Service  
toll-free at 1-800-800-812, or write to:Fisher-Price, Mattel Pty. Limited,  
461 Plummer Street, Port Melbourne,Victoria 3207.  
• Rotate the desk top down.  
Helpful Hint: When converting the desk back to a toddler  
bed, rotate the desk top upright and lift to remove it from  
the desk.  
Desk assembly is now complete.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Chainsaw X52000020 User Manual
Excalibur electronic Car Speaker 184 User Manual
Fellowes Paper Shredder 3250C User Manual
Fisher Price Baby Toy W9732 User Manual
Flowtron Outdoor Products Trimmer LE 800B User Manual
Frigidaire Air Conditioner THRU THE WALL AIR CONDITIONER User Manual
Frymaster Fryer FR 3 User Manual
GE Monogram Refrigerator ZISW B480DX User Manual
GE Ventilation Hood ZV750 User Manual
Gianni Industries Door DK 502 User Manual