Fisher Price High Chair H4790 User Manual

Product features and decorations may vary from photo above.  
Instructions  
Model Number: H4790  
WARNING  
IMPORTANT! KEEP FOR FUTURE REFERENCE.  
Please read these instructions before assembly and use of this product.  
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
Pad  
2 Toys (Toys may be different)  
3 Food Trays  
Headrest  
Seat Back  
Hinge Rod  
Base Tray  
#10 x 2.2 cm  
Black Screw  
Frame  
Frame  
2 Seat Bottom Tubes  
Seat Bottom  
#8 x 1.9 cm Screws  
4 Screw Retainers  
#8 x 1.9 cm Screws  
#10 x 2.2 cm  
Black Screw  
Back Base  
Footrest  
Basket  
Storage Caddy  
Tighten and loosen all screws with a Phillips screwdriver.  
Do not over-tighten the screws.  
Front Base  
#10 x 2.2 cm Black Screw - 7  
Shown Actual Size  
#8 x 1.9 cm Screw - 8  
#10 x 2.2 cm  
Black Screw  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
IMPORTANT! Before each use, inspect this product for damaged  
hardware, loose joints, missing parts or sharp edges. DO NOT use  
if any parts are missing or broken. Contact Mattel for replace-  
ment parts and instructions if needed. Never substitute parts.  
Plastic Rings  
Seat Bottom Tubes  
Footrest  
Seat Bottom  
1
• Place the seat bottom face down on a flat surface.  
• At an angle, fit the footrest on the seat bottom, as shown.  
Plastic Rings  
Plastic Rings  
3
#8 x 1.9 cm Screw - 4  
• Align the holes in the plastic rings and the seat bottom tubes.  
• Insert a #8 x 1.9 cm screw through each plastic ring and into  
the seat bottom tubes, as shown. Tighten the screws.  
Seat Bottom Tubes  
• Push the seat bottom tubes back and forth to be sure they are  
secured to the seat bottom. If the seat bottom tubes move, you  
have probably not fastened them properly. Remove the screws  
and check to be sure the screw holes in the seat bottom tubes  
and seat bottom plastic rings are aligned. Replace and tighten  
the screws.  
2
Plastic Rings  
• Slide a seat bottom tube through each set of plastic rings on  
the seat bottom.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Footrest  
Insert Screws Here  
Hinge  
Hinge Rod  
4
6
#10 x 2.2 cm Black Screw - 2  
#10 x 2.2 cm Black Screw  
• Insert two #10 x 2.2 cm black screws through the footrest and  
• Turn the seat assembly face down.  
• Insert the hinge rod through the hinge on the seat back and  
seat bottom, as shown.  
into the seat bottom. Tighten the screws.  
• Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten  
the screw.  
Seat Back Pin  
Seat Back Pin  
• Set the seat assembly aside for Assembly step 9.  
Frame Leg  
Opening  
Opening  
7
Seat Bottom Assembly  
5
• Pull the frame leg out on each frame to open. Make sure it  
• Turn the seat bottom assembly upright.  
• Fit the seat back pins into the openings in the top side of the  
seat bottom assembly.  
"clicks" into place.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Seat Height Adjusters  
Back Base  
Position 4  
Tapered Leg Tube  
Press Lever  
8
Front Base  
10  
• Identify the back and front base. The front base has tapered leg  
tubes. You will use the back base for the next assembly step.  
• While pressing the levers on the seat height adjusters, lift them  
to position 4 on the frame front legs, as shown.  
Frame Decorated Side  
Seat Assembly  
#10 x 2.2 cm Black Screw - 2  
Frame Back Legs  
Sockets  
Screw Retainer - 2  
Back Base Hole  
Screw Retainers  
Seat Bottom Tubes  
11  
Back Base Hole  
9
• Fit the seat assembly between the two frames.  
• Insert the seat bottom tubes into the sockets in each seat  
height adjuster.  
• Position a frame so that the decorated side is outward.  
• Insert the back leg of a frame into the back base.  
• Fit a screw retainer over the hole in the back base, as shown.  
• Insert a #10 x 2.2 cm black screw through the screw retainer  
and back base. Insert the back leg of a frame into the back  
base. Tighten the screw.  
Hints:  
Be sure the seat height adjusters are in the same position (position 4).  
You may need to push the frames apart slightly to fit the seat bottom  
tubes into the seat height adjuster sockets.  
• Repeat this procedure to attach the other frame back leg  
to the other side of the back base.  
Hint: The #10 x 2.2 cm black screws may have been assembled to the  
screw retainers.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
#10 x 2.2 cm Black Screw - 2  
Screw Retainer - 2  
Push Seat  
Height  
Adjuster  
Push Seat  
Height  
Adjuster  
Front  
Leg Holes  
Screw Retainers  
Seat Bottom Tube Ends  
12  
13  
#8 x 1.9 cm Screw - 2  
• Push each seat height adjuster to be sure they are completely  
on the seat bottom tubes.  
• Insert a #8 x 1.9 cm screw through each seat height adjuster  
and the ends of the seat bottom tube. Tighten the screws.  
• Insert the frame front legs onto the front base.  
• Fit a screw retainer over a hole in the front leg.  
7
• Insert a #10 x /8" (2.2 cm) black screw through the screw  
retainer and front leg. Tighten the screw.  
• Repeat this procedure to secure the other end of the front  
base with the remaining screw retainer and #10 x 2.2 cm  
black screw.  
Hint: The #10 x 2.2 cm black screws may have been assembled to the  
screw retainers.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Pad  
Seat Height Adjusters  
#8 x 1.9 cm Screw - 2  
Elastic Loops  
Hole  
Hole  
Front View  
Seat Bottom Tube Ends  
Back and Bottom View  
14  
Tabs  
• From the back and bottom of the assembly, insert a #8 x 1.9 cm  
screw through both seat height adjusters and the ends of the  
seat bottom tube. Tighten the screws.  
Elastic Loops  
15  
Back and Bottom View  
• Lift the assembly upright.  
• From the front of the assembly, place the pad onto the seat.  
• Lift the bottom of the pad. Insert the two elastic loops on the  
pad through the holes in the seat bottom.  
• From the back and bottom of the seat, hook the elastic loops to  
the tabs on the seat.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Upper Shoulder Belt Slots  
Shoulder Portion  
Lower Shoulder  
Belt Slots  
Headrest Pad Slots  
Slot  
Crotch  
Belt  
16  
Shoulder Portion  
• Insert the crotch belt through the slot in the pad. Make sure  
the crotch belt is not twisted.  
• Fold the top of the pad down.  
18  
• Fit the top of the pad over the seat back.  
• Fold the bottom edge of the pad under the edge of the seat  
bottom to fasten it.  
• Remove the shoulder portion of the waist/shoulder belts by  
feeding them through the slots in the seat back.  
• First, insert the shoulder portion of the shoulder/waist belt  
through the slots in the headrest pad. Then, insert  
the shoulder portion of the shoulder/waist belt through the  
slots in the pad and seat back.  
- Use the lower shoulder belt slots for a smaller baby.  
- Use the upper shoulder belt slots for a larger baby.  
Bottom Slots  
17  
• Lift the top of the pad.  
• Thread the waist/shoulder belts through the bottom slots in the  
back of the seat pad.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Frame Tab  
Pad Strap  
Handle  
Storage Caddy  
Headrest Strap  
Small Fastener  
21  
Large Fastener  
• Fit the storage caddy onto either frame tab.  
19  
Back View  
• Fit the strap on the top of the headrest through the handle.  
• Fit the pad strap through the handle and press it to the small  
fastener on the back of the seat.  
Basket  
• Fit the headrest strap through the handle and press it to the  
large fastener on the back of the seat.  
Elastic Loop  
Elastic Loop  
Tab  
22  
Tab  
• Fit the basket onto the other frame tab.  
Assembly is now complete.  
Belt Ends  
20  
Back View  
• From behind the seat, be sure the shoulder portion of the  
waist/shoulder belts are secure in the seat back slots.  
• Hook the elastic loops on each side of the pad onto the tabs  
in the seat back.  
Download from Www.Somanuals.co1m0. All Manuals Search And Download.  
Securing Your Child  
IMPORTANT! Before each use, inspect this product for damaged  
hardware, loose joints, missing parts or sharp edges. DO NOT use  
if any parts are missing or broken. Contact Mattel for replace-  
ment parts and instructions if needed. Never substitute parts.  
Place the high chair on a level, stable surface away from electri-  
cal flexes. Be sure to keep electrical flexes out of child’s reach.  
Anchored End  
Buckle  
A
B
Free End  
WARNING  
Prevent serious injury or death from  
falls or sliding out. The child should at all  
times wear a safety harness correctly fitted  
and adjusted. The tray is not designed to  
hold the child in the chair.  
Tighten  
2
To tighten the waist belts: Feed the anchored end of the waist  
A
belt up through the buckle to form a loop . Pull the free end  
B
of the waist belt  
.
Waist/Shoulder Belt  
Waist/Shoulder Belt  
Anchored End  
Buckle  
B
A
Free End  
Loosen  
3
To loosen the waist belts: Feed the free end of the waist belt up  
Crotch Belt  
A
through the buckle to form a loop . Enlarge the loop by pulling  
1
on the end of the loop toward the buckle. Pull the anchored end of  
B
the waist belt to shorten the free end of the waist belt  
.
• Place your child in the seat. Position the crotch belt between  
your child’s legs.  
• Fasten both waist/shoulder belts to each side of the crotch belt.  
Make sure you hear a "click" on both sides.  
Check to be sure the restraint system is securely attached by  
pulling it away from your child. The restraint system should  
remain attached.  
11  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing Your Child  
Hold Adjuster  
Shoulder Portion  
Pull Strap Down  
Slide Adjuster  
Down  
6
• From the front of the high chair, pull the shoulder portion of  
the waist/shoulder belts out and then fit them back through  
the desired shoulder belt slots in the headrest pad, seat pad and  
the seat back. Pull on the belts to be sure they are secure in the  
seat back.  
4
Tighten  
Loosen  
To tighten the shoulder belts: Hold the adjuster and pull the  
front shoulder strap down.  
To loosen the shoulder belts: Slide the adjuster down.  
Note: After adjusting the restraint system to fit your child,  
make sure you pull on it to be sure it is securely fastened.  
5
To change shoulder belt slots:  
• From the back of the high chair, push the shoulder portion of  
the waist/shoulder belts through the seat back slots.  
Download from Www.Somanuals.co1m2. All Manuals Search And Download.  
Using the Trays and Toys  
WARNING  
Base Tray  
Prevent serious injury or death from  
falls or sliding out. The child should at all  
times wear a safety harness correctly fitted  
and adjusted. The tray is not designed to  
hold the child in the chair.  
Release Bar  
8
Hint: The base tray can be adjusted for your child’s comfort two ways  
(see steps 8 and 9)!  
• While pushing the release bar on the front of the base tray,  
adjust the base tray forward or backward.  
Base Tray  
Armrest  
Squeeze Latch  
Base Tray  
9
• While squeezing the latches underneath the base tray, adjust  
the base tray forward or backward.  
7
• Fit the base tray onto the seat armrests. Push down until the  
base tray "snaps" into place.  
Hint: Before use, thorougly wash all parts (the trays) that may contact food.  
Download from Www.Somanuals.co1m3. All Manuals Search And Download.  
Using the Trays and Toys  
Food Tray  
Base Tray  
Squeeze Latch  
Base Tray  
10  
12  
Hint: The base tray can be removed two ways (see steps 10 and 11)!  
• Fit the food tray into the base tray, as shown.  
• Squeeze one or both of the latches underneath the base tray  
and lift.  
Hint: Before use, thorougly wash all parts (the trays) that may contact food.  
Toy  
Base Tray  
Tab  
Release Bar  
Slot  
Tab  
11  
13  
• While pushing the release bar on the front of the base tray, pull  
the tray base towards you and remove.  
• Insert and “snap” either toy tab into either slot in the tray.  
Hint: To remove a toy, press the tab and lift the toy.  
Download from Www.Somanuals.co1m4. All Manuals Search And Download.  
Adjusting the Seat  
Upright  
WARNING  
Semi-Recline  
Recline  
Prevent serious injury or death from  
falls or sliding out. It is recommended  
that the high chair be used in the upright  
position only by children capable of sitting  
upright unassisted.  
Seat Height Adjuster  
Squeeze  
Back View  
Press Lever  
15  
4
Hint: Adjust the seat angle to any of three positions: Upright, Semi-  
Recline or Recline.  
To adjust the seat angle:  
14  
• Squeeze the seat back handle and push the seat back forward  
or, pull it backwards to the desired position.  
• Push the seat back to be sure it is latched in position.  
Hint: Adjust the seat height to any of seven positions!  
To adjust the seat height:  
• Press the levers on both seat height adjusters and lift or lower  
the seat to the desired height.  
• Make sure both sides of the seat are adjusted to the same  
height. Push the seat bottom to be sure the seat is locked  
in place.  
Download from Www.Somanuals.co1m5. All Manuals Search And Download.  
Storage  
Care  
• The pad and headrest are machine washable. Wash them sepa-  
rately in cold water on the gentle cycle. Do not use bleach.  
Line dry.  
• The frame and base tray may be wiped clean using a mild  
cleaning solution and a damp cloth. Do not immerse the  
base tray.  
• The food trays and toys are dishwasher safe. Simply remove  
the food tray from the base tray and place in your dishwasher.  
To remove the pad:  
Base Tray  
• Remove the four elastic loops from the pegs on the underside  
and back of the seat.  
• Unfasten the pad strap from the seat back.  
• Feed the shoulder portion of the waist/shoulder belts through  
the slots in the seat back and the pad.  
Hole  
• Feed the waist portion of the waist/shoulder belts and crotch  
belt down through the slots in the seat.  
• Remove the waist/shoulder belts and crotch belt through the  
slots in the pad.  
• Unfasten the pad fasteners from the front edge of the seat  
bottom.  
• Remove the pad.  
Peg  
• To replace the pad: refer to Assembly steps 15-20.  
IMPORTANT! Never use this product without the restraint system.  
Replace the waist/shoulder belts and crotch belt.  
16  
• Fit the holes on the base tray latches onto the pegs on the back  
of the high chair frame.  
Consumer Information  
Great Britain: Mattel UK Ltd. Vanwall Business Park,  
Maidenhead SL6 4UB. Helpline: 01628 500302.  
Australia  
Pull Frame  
Release Latch  
Mattel Australia Pty. Ltd., 658 Church Street,  
Locked Bag #870, Richmond, Victoria 3121 Australia.  
Consumer Advisory Service 1300 135 312.  
New Zealand  
16-18 William Pickering Drive, Albany 1331, Auckland.  
Asia  
Mattel East Asia Ltd, Room 1106, South Tower,  
World Finance Centre, Harbour City, Tsimshatsui, HK, China.  
17  
• With the legs all the way open, lower the seat to position 7 the  
lowest position).  
• Pull the frame release latches forward and push the rear legs  
toward the front legs.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.  
©2004 Mattel, Inc. All Rights Reserved.  
® and ™ designate U.S. trademarks of Mattel, Inc.  
PRINTED IN CHINA  
H4790a-0726  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Everpure Water System CG53 20S User Manual
Fender Stereo Amplifier 1970 Relic Stratocaster User Manual
FieldServer Computer Drive FS 8700 104 User Manual
Franke Consumer Products Plumbing Product FF 2000 User Manual
Furuno Network Router FELCOM 250 User Manual
Furuno Radar Detector FS 1503EM User Manual
GE Cordless Telephone 28321EE1 User Manual
GE Microwave Oven PVM2070DMWW User Manual
Gemini CD Player CDJ 1200 User Manual
Golden Technologies Wheelchair GP160 User Manual