Battery Installation
Assembly
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel for
replacement parts and instructions if needed. Never substitute parts.
Hint: We recommend using alkaline batteries for
longer battery life.
1,5V x 4
“D” (LR20)
Base Tubes
Lift
Lift
Base
1
• Lift both base tubes.
Hubs
• Loosen the screws in the battery compartment door and remove
the battery compartment door.
• Insert four“D”(LR20) alkaline batteries into the battery compartment.
• Replace the battery compartment door and tighten the screws.
• Low battery power may cause this product to operate erratically
(no movement/no sounds) and the product may not turn off. If this
should happen, remove and discard all batteries and replace with
four, new “D” (LR20) alkaline batteries.
Base Tubes
Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).
Base Tubes
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
2
• Position the hubs with the smooth side out.
• Fit the hubs onto the base tubes.
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire.The batteries inside may
explode or leak.
Hint: The hubs are designed to fit the base tubes one way. If the
hubs do not fit on the base tubes, check to be sure the smooth side
is out.
• Never short-circuit the battery terminals.
• Push the hubs down until you hear a “click”.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Pull up on the hubs to be sure each is secure.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seatback Tube
Wide Slot
Narrow Slot
Footrest Tube
5
3
• Position the pad onto the frame assembly.The extra, padded portion
should be toward the seat back tube.
• Position the footrest tube so that it curves down.
• Fit the ends of the footrest tube into the wide slots in the hubs.
• Position the seat back tube so that it curves down.
• Fit the ends of the seat back tube into the narrow slots in the hubs.
Seat Back Tube
Hubs
6
• Fit the upper pocket on the pad around the seat back tube.
4
• Insert a #8 x 3,2 cm screw into each hub and tighten.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Headrest Pad
Footrest Tube
Restraint
Belts
7
• Fit the lower pocket on the pad around the footrest tube. Fasten the
straps underneath the footrest tube to secure the lower portion of
the pad.
9
• Fit the restraint belts through the slots in the headrest pad.
• Fit the headrest pad to the liner/pad.
PUSH
PUSH
Toy Bar
Sockets
8
• Push down on the pad to be sure it is assembled properly. If the
pad falls through the frame, you have not assembled it properly.
Please re-read these instructions and re-assemble the pad.
10
• Fit the toy bar plugs into the frame sockets..
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-up
WARNING
To prevent serious injury or death from falls
and being strangled in the restraint system:
• Fall Hazard - It is dangerous to use this
product on an elevated surface, since
child’s movement may cause the product
to slide or tip over. Use only on a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffoca-
tion in soft surfaces.
• Always use the restraint system.
Back View
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
Seat Position
• Adjust the seat position for baby’s comfort.
• Lift the fabric skirt near the seat back of the frame.
Upright: Fasten the liner/pad buckles. Make sure you hear a “click”.
Recline: Unfasten the liner/pad buckles.
• Never leave child unattended.
• Never use the toy bar as a handle.
Side-to-Side
Head-to-Toe
Swinging Direction
• Adjust the seat to change gliding motion to: Side-to-Side or
Head-to-Toe.
• Turn the seat for baby’s comfort.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing Baby
Starting Gliding Motion
Restraint Belts
Restraint Pad
• Place your child in the product. Position the restraint pad between
your child’s legs.
• Fasten both restraint belts to the buckles on each side of the
restraint pad. Make sure you hear a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child.The restraint system should
remain attached.
Power/Speed Switch
Anchored End
Anchored End
Free End
Free End
• Make sure your child is properly secured in the seat.
TIGHTEN
LOOSEN
• Slide the power/speed switch to slow
or fast
.
Hint:. In most cases, the slow setting works best for a smaller child,
while the fast setting works best for a larger child. If gliding stops
while using the slow setting, try the fast setting. Give the seat a light
push to start the gliding motion again.
To tighten the belts: Feed the anchored end of the restraint up
through the buckle to form a loop Ạ. Pull the free end of the
restraint ạ.
To loosen the belts: Feed the free end of the restraint up through
the buckle to form a loop Ạ. Enlarge the loop by pulling on the end
of the loop toward the buckle. Pull the anchored end of the restraint
to shorten the free end of the belt ạ.
• Be sure to turn this product off when not in use. Slide the power/
speed switch to the off setting
.
• For best performance, make sure this product is used on a
completely level surface.
Please Note: After adjusting the restraint system to fit your child, make
sure you pull on it to be sure it is securely fastened.
Note: If gliding motion is slow in one direction (and you hear a winding
or grinding noise), you may be using this product on an inclined surface.
Use this product only on a completely level surface.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Room-to-Room Portability
Music
Music Switch
• Choose the style of music for baby. Slide the music switch to:
Soothing
Playful
Off
• Slide the volume switch to
for low volume;
for high volume.
Note: Low battery power may cause this product to operate erratically
(no movement/no sounds) and the product may not turn off. If this
should happen, remove and discard all batteries and replace with four,
new “D” (LR20) alkaline batteries.
• Make sure your child is properly secured in the glider.
• Grasp both handles, as shown, and lift.
• Carefully carry the glider to another room. Be sure to set the glider
down only on the floor.
Care
• The liner/pad and headrest pad are machine washable.Wash them
separately in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
• The frame and toy bar may be wiped clean using a mild cleaning
solution and a damp cloth. Do not immerse the frame.
To remove the liner and headrest pad:
• Feed the restraint belts back through the slots in headrest pad.
Pull to remove the headrest pad.
• Lift the fabric skirt near the footrest of the frame.
• Unfasten the liner/pad buckles. Pull to remove the liner/pad bottom
pocket from the footrest tube; pull to remove the liner/pad upper
pocket from the seatback tube.
• To replace the pad: refer to Assembly step 5 - 9.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|