T4201
Infant Rocker Seat -
Recline Position
Toddler Rocker -
Upright Position
IMPORTANT!
KEEP FOR FUTURE
REFERENCE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Assembly
IMPORTANT! Please remove all parts from the package and
identify them before assembly. Some parts may be packed
in the pad.
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
®
Fisher-Price for replacement parts and instructions if needed.
Never substitute parts.
Seat Back Tube
PRESS
2 Side Rails
Pad
Seat Back Tube
2 Retainers with Lock Nut
PRESS
Toy Bar
Side Rails
Back Crossbar
1
• Fit the ends of the seat back tube to the ends of each side rail.
Hint: The seat back tube is designed to fit one way. If it does not
seem to fit, turn it around and try again.
• While pressing the button on the end of the seat back tube/side
rail, continue to insert until the buttons “click” into place.
Make sure you hear a “click” on each side.
Kickstand
Front Crossbar
• Pull the seat back tube to be sure it is secure on the side rails.
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
M5 x 30 mm Screw – 6
Shown Actual Size
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
PRESS BUTTONS
Back Crossbar
Side Rails
Screws
4
2
• Insert a screw through the outside hole in each side rail and into
the ends of the front crossbar.
IMPORTANT! Please follow the next assembly step (step 5)
carefully to completely secure the front crossbar to the side rails.
• While pressing the buttons on the ends of the back crossbar,
insert into the ends of the side rails. Push the back crossbar until
the buttons "click" into place. Make sure you hear a “click” on
each side.
Hint: The back crossbar is designed to fit the ends of the side rails
one way.
• Pull the back crossbar to be sure it’s secure to the side rails.
Side Rail Hole
Retainer with Lock Nut
5
• Fit a retainer with lock nut onto the end of the screw and to the
inside of a side rail. Tighten the screw.
Hint: A lock nut has been factory assembled to the retainer. During
shipment, the lock nut may have fallen out of the retainer. If it
has, please fit it into the hexagonal hole in the retainer so that the
rounded side of the lock nut faces out.
Power Switch
Front Crossbar
Side Rail Hole
3
• Repeat this procedure to fasten the screw in the other side rail,
using the remaining retainer with lock nut.
• Position the front crossbar so that the vibration unit power
switch is down.
• Fit the front crossbar tabs to the small hole in each side rail.
Hold the front crossbar in place and proceed to steps 4 and 5
to fasten.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad
Kickstand
6
• Fit the kickstand onto the assembly, as shown.
8
• Fit the pad pocket onto the seat back tube.
Waist Belts
Screws
Screws
7
• Insert four screws into the kickstand and tighten.
BACK VIEW
9
• Insert the waist belts through slots in the back of the pad.
• Press the fastener on the waist belts and pad together.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Battery Installation
Hint: We recommend using an alkaline battery for longer
battery life.
1,5V
+
-
“D” (LR20)
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
Pad Buckles
• Locate the battery compartment on the bottom of the
vibrations unit.
• Loosen the screw in the battery compartment door. Lift to
remove the battery compartment door.
• Insert one “D” (LR20) alkaline battery.
• Replace the battery compartment door and tighten the screw.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the power switch off and then back on.
IMPORTANT! Low battery power causes this product to operate
erratically: no vibrations and the product may not turn off.
Remove and discard the battery and replace with a new
“D”(LR20) alkaline battery.
10
• Fasten both buckles on the front edge of the pad around the front
crossbar. Make sure you hear a "click" for each buckle.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup and Use
Infant - Recline
WARNING
To prevent serious injury or death:
• Fall Hazard - Never use this product on an
elevated surface, since child’s movement may
cause the product to slide or tip over. Use
only on a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffocation in
soft surfaces.
1
BACK VIEW
Seat Position
• Fasten the straps on the back of the pad for the Infant-Recline Position.
• Never leave child unattended.
• Never use as a carrier or lift while child
is seated.
• This product is not intended to replace a cot
or bed for prolonged periods of sleep.
• Use the upright position (toddler mode) only
when child has developed enough upper
body control to sit without leaning forward.
• Always use the restraint system until
child is able to climb in and out of the
product unassisted.
Kickstand
2
Kickstand
• Rotate the kickstand out for a stationary feeding seat.
• Push down on the seat bottom to be sure the kickstand
is in position.
• Do not use reclined position (infant mode)
once child can sit unaided.
• Never use toy bar as a handle.
Waist Belt
Waist Belt
Restraint Pad
3
Restraint System
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the waist belts to each side of the restraint pad.
Make sure you hear a “click” on both sides.
• Tighten each waist belt so that the restraint system is snug
against your child. Please refer to the next section for
instructions to tighten the waist belts.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Infant - Recline
Toddler - Upright
Anchored End
Anchored End
1
BACK VIEW
Free End
Free End
Seat Position
• Fasten the straps on the back of the pad for the
Toddler-Upright Position.
4
TIGHTEN
LOOSEN
To tighten the belts:
• Feed the anchored end of the restraint belt up through the buckle
A
B
to form a loop . Pull the free end of the restraint belt
.
Small Slot
To loosen the belts:
• Feed the free end of the restraint belt up through the buckle to
A
form a loop . Enlarge the loop by pulling on the end of the
loop toward the buckle. Pull the anchored end of the restraint
B
belt to shorten the free end of the restraint belt
.
Large Slot
2
5
• Insert the waist restraint belts back through the small slots in
the pad.
• Insert the restraint pad down through the large slot in the pad.
Toy Bar
• Fit the plugs on each end of the toy bar into the sockets in each
side rail.
• Use the toy bar only in infant mode.
• To remove the toy bar, press the tabs on the toy bar plugs and lift.
3
BACK VIEW
Power Switch
• From the back of the pad, buckle the waist belts to the restraint
pad. Tuck the free ends of the waist belts into the openings in
the pad.
6
• Slide the power switch to the on position for calming
vibrations. Slide the power switch to the off position to turn
vibrations off.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|