G5760
DowCnloaod froam Wswtw.aSomlanuWals.coimn. Aldl MasnualsASeiarrchpAndoDorwtnlo™ad.
Battery Installation
Parts
B. Long Runway
C. Short Runway
D. Arm
A. Airplane
B
A
D
G
C
F
I
1.5V x 3
“C” (LR14)
Shown Actual Size
E. Control Tower
F. Tower Base
G. Controller Base
H. Crane
I. Straight Track
J. 2 Flags
E
K. Cargo Tray
L. Sign
M. Windsock
N. Handle
O. 2 Cargo Crates
P. Train
BOTTOM VIEW
Q. 2 Small Ramps
• Locate the battery compartment door on the
bottom of the tower base.
• Loosen the screws in the battery compartment
door with a Phillips screwdriver. Remove the
battery compartment door.
Please keep this instruction
sheet for future reference, as it
contains important information.
Requires three “C” (LR14)
alkaline batteries (not included).
H
• Insert three “C” (LR14) alkaline batteries.
Adult assembly is required.
• Replace the battery compartment door and
tighten the screws with a Phillips screwdriver.
Do not over-tighten.
• When sounds, lights or motions from this toy
become faint or stop, it’s time for an adult to
change the batteries.
Tools required for battery
installation: Phillips screwdriver
(not included).
J
K
L
M
Q
Battery Safety Information
Batteries may leak fluids that can cause a chemical burn injury or
ruin your toy. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Dispose of batteries safely.
• Never short-circuit the battery terminals.
x2
N
O
P
• Use only batteries of the same or equivalent type, as
recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging.
• If removable, rechargeable batteries are used, they are only to
be charged under adult supervision.
x2
x2
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
3
1
2
4
Fit the peg on one side of the cargo
tray into the hole in the tower base.
Press and “snap” the peg on the
opposite side of the tray into the other
hole in the base.
“Snap” the control tower into the
tower base.
“Snap” the arm into the top of the
control tower.
“Snap” the flags into the tower,
as shown.
6
5
7
“Snap” the controller base into the
tower base, as shown.
“Snap” the handle on to the post on
the controller base.
Fit the long and short runways onto
the controller base, as shown.
Hint: The two runway pieces can be
removed for storage.
Assembly is now complete!
Download from Www.Somanuals.com. All Manuals Search And Download.
Ready for Takeoff!
1
2
On/Off Switch
• Locate the On/Off switch on the bottom of
the tower base.
• Slide the switch to the
the toy on and to the
it off.
position to turn
position to turn
If you haven’t used the toy for a few minutes it goes to sleep.
To “wake up” the control tower, press the reset button near the
bottom of the tower.
Press to “snap” the plane to the arm.
4
Hint: Additional GeoTrax™ planes also work
with the airport (sold separately and subject
to availability).
3
Rotate the luggage carousel to get cargo
from the train to the plane.
Use the crane to pick up and load cargo.
• Pull back on the
controller handle
to raise the air-
PRESS
plane with realistic sound effects and
flashing lights. The more you pull back,
the higher the plane flies.
PRESS
• Push the handle forward to lower and
land the plane.
Turn the selector dial to choose the sounds
of a jet, a propeller plane or a helicopter.
The crane, windsock and sign have a small
tab that fits into a matching notch in the
runway, the tower base or any track piece.
For storage, press the buttons on the sides
of the controller base and pull to remove.
Download from Www.Somanuals.com. All Manuals Search And Download.
|