900MHz Long Range
Monitor
Model Number: C7051
For proper setup and use, please read these instructions.
Please keep this instruction sheet for future reference,
as it contains important information.
Transmitter is electrically powered.
Includes one AC adaptor to power receiver (plugs into
standard household outlets). Receiver also runs on battery
power (three LR03 “AAA” alkaline batteries – not included).
Adult assembly is required to install the batteries.
Tool needed for battery installation:
Phillips screwdriver (not included).
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiver Battery Installation (Optional)
The receiver operates using the enclosed
AC adaptor or battery power.
1.5V x 3
LR03 “AAA”
Battery
Compartment
Door
Shown Actual Size
• Locate battery compartment
door on back of receiver.
• Loosen screw in battery
compartment door with a
Phillips screwdriver. Remove
battery compartment door.
• Insert three LR03 “AAA”
alkaline batteries as
indicated inside battery
compartment.
Hint: We recommend use of alkaline batteries for longer battery life.
• Replace battery compartment door.Tighten screw with a Phillips screwdriver.
Battery Safety Information
Batteries may leak fluids that can cause a chemical burn injury or ruin
your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of batteries in a fire. The batteries may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing Reception (for Sound)
Test transmitter transmission and receiver reception
each time you change location of use.
Power
Indicator
Power
Switch
Power/Volume
Dial
Power
Indicator
Set channel switch on transmitter to Place receiver in room in which
the same channel as receiver. Place
transmitter in room in which you
intend to use it. Slide transmitter
power switch to turn power on.
Power indicator lights. Turn on a radio.
you intend to use it. Rotate the
power/volume dial to turn power
on. Power indicator lights. Adjust
receiver location.
• Variable light display lights when
sound is received by receiver:
- One two dots light for
shallow sounds.
Adjust
Channel
- Three or more dots light for
louder sounds.
If you experience interference
(buzzing or static, etc.) while using
one channel setting, switch both
units to other channel. Selecting
a channel is usually a one time
adjustment.
Hint: All five dots in receiver variable light display light:
- If you turn receiver power on before transmitter power. You will also hear
static noise. Turn volume down on receiver and turn transmitter power on.
- If the receiver is too far away from the transmitter. Move the receiver closer
to the transmitter.
- If loud sounds are transmitting.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing Reception (for Vibrations)
Test transmitter transmission and receiver reception
each time you change location of use.
Power
Indicator
Power/Volume
Dial
Power
Switch
Vibrations
Ready
Indicator
Power
Indicator
Vibrations
Button
Set channel switch on transmitter
to the same channel as receiver.
Place transmitter in room in which
you intend to use it. Rotate trans-
mitter power switch to turn
power on. Power indicator lights.
Turn on a radio.
Clip receiver to your clothing (where
you will feel vibrations). Walk to
the furthest point of use. Rotate
power/volume dial to turn power
on. Power indicator lights. Now, press
the vibrations button. Vibrations
ready indicator lights.
Hint: You can also place the
receiver in your pocket.
• When sound is received, vibrations
begin and variable light display
lights on receiver.
Adjust
Channel
• To turn off vibrations, press
vibrations button. Vibrations
ready indicator turns off.
• If you experience interference
(vibration) when it is obvious
that no sound is transmitting
while using one channel setting,
switch both units to other channel.
Selecting a channel is usually a
one time adjustment.
Adjust
Channel
Vibrations Button
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up For Sounds‘n Lights Use
1
4
2
3
7
1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT! Test sound reception of this monitor before first time
use and whenever you change location of transmitter (see page 5).
Set transmitter channel switch to same channel as receiver.
1
2
Place transmitter in same room with child. Point microphone
directly toward crib or play area.
Unwrap and fully extend power cord for best transmission.
Plug transmitter power cord into wall outlet.
3
4
Slide transmitter power switch to turn power on.
Power indicator lights.
Place receiver where you will see or hear it.
5
6
If you will be using receiver near a wall outlet, we recommend
that you use the AC adaptor. Unwrap and fully extend AC
adaptor cord for best reception. Plug AC adaptor cord into
wall outlet.
Rotate receiver power/volume dial to turn power on. Power
indicator lights. Rotate power/volume dial to adjust volume.
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up For Vibrations Use
“Wah, Wah,
Wah…”
2
3
1
4
7
5
6
1
IMPORTANT! Test reception of this monitor before first time
use and whenever you change location of transmitter (see page 5).
Set transmitter channel switch to same channel as receiver.
1
2
Place transmitter in same room with child. Point microphone
directly toward crib or play area.
Unwrap and fully extend power cord for best transmission.
Plug transmitter power cord into wall outlet.
3
4
5
6
Slide transmitter power switch to turn power on.
Power indicator lights.
Clip receiver to your clothing, where you will feel vibrations.
Or, place the receiver in your pocket.
Rotate receiver power/volume dial to turn power on. Power
indicator lights. Rotate power/volume dial to adjust volume
(if you want to hear sounds).
Press the vibrations button. Vibrations ready indicator lights.
7
Hint: Under permitting conditions, the receiver receives sounds (and you
will feel vibrations) up to 305 meters away from baby.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems & Solutions
Circuit Breaker
5
“Ma, ma, ma.
Da, da, da…”
3
4
“That doesn’t
sound right. Maybe
we should check the
transmitter.”
6
BUZZZZ
2
1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems & Solutions
PROBLEMS
SOLUTIONS
Transmitter power indicator
not lit.
Turn transmitter power on.
Power indicator lights.
1
2
1
2
You hear static or buzzing
from receiver.
Make sure channel switches on
both transmitter and receiver set
to same channel.
Transmitter power indicator
not lit.
Make sure light switch that
controls power flow to wall
outlet is on.
3
3
Transmitter power indicator
not lit.
Check AC adaptor cord
plug-to-outlet connection.
4
5
4
5
Transmitter power indicator
not lit.
Power is off because circuit breaker
for baby’s room off. Make sure
house fuses and circuit breakers
are on.
Check all five solutions above.
Any one or more of these solutions
should solve the problem.
You hear static or buzzing and
all five dots lit on receiver.
6
6
Hint: If, after checking all of these solutions, you believe that your
AC adaptor is damaged, please contact Mattel.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems & Solutions
“That’s gotta
be coming from
next door…”
“Did you read
about…”
PROBLEM
You can hear conversations or sounds from other homes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
“Wah, Wah,
Wah…”
“That must
be Susie
next door…”
“I better get
off the phone,
she’s up…”
“Wah, Wah,
Wah…”
“Wah, Wah,
Wah…”
“Did you read
about…”
SOLUTION
There is signal interference due to other nursery monitors on same
channel or cordless telephone use. Change channel switches on
both transmitter and receiver to eliminate source of interference.
Hints:
- Do not use more than one transmitter and one receiver at same time
in same household.
- Always remember that you are using public airwaves when using
your monitor. Conversations, even from rooms near transmitter, may
broadcast to other nursery monitors, radios, cordless telephones, or
scanners outside your home. To protect privacy of your home, always
turn transmitter off when not in use.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems & Solutions
“Uh-oh, maybe I
should move closer
to the house.”
SOLUTION
PROBLEM
The receiver vibrates, all five
dots light and if you have the
sound turned up – you hear
static or buzzing.
Receiver is out of range of trans-
mitter. Move receiver closer to
transmitter.
Note: Range varies depending
on surrounding conditions such
as noise levels, physical obstruc-
tions and signal interference.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Information
AUSTRALIA
Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1 300 135 312.
NEW ZEALAND
16-18 William Pickering Drive, Albany 1331, Auckland.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Care
Excess dirt in transmitter microphone will hamper transmission of sound.
Clean outer surface of transmitter and receiver with a cloth lightly
dampened with a mild cleaning solution.
Never immerse transmitter, receiver or AC adaptor.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
One (1) Year Limited Warranty
Mattel Australia Pty. Ltd., (658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia) warrants that the 900MHz Long Range Monitor is
free from all defects in material and workmanship when used under normal
conditions for a period of one (1) year from the date of purchase. Should
the product fail to perform properly, we will repair or replace it at our option,
free of charge. Purchaser is responsible for shipping the product to
Consumer Relations at the address indicated above and for all associated
freight and insurance cost. Fisher-Price, Inc., will bear the cost of shipping the
repaired or replaced item to you. This warranty is void if the owner repairs
or modifies the product. This warranty excludes any liability other than
that expressly stated above including but not limited to any incidental
or consequential damages.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
The electronic components in transmitter, receiver and AC adaptor are not
designed for consumer repair. Evidence of any attempt of consumer repair
will void this warranty.
Consumer Advisory Service phone numbers are as follows:
Australia 1 300 135 312
New Zealand 0800 174 063
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2004 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA
C7051pr-0729
Download from Www.Somanuals.com. All Manuals Search And Download.
|