P7866
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three "C" (LR14) alkaline batteries
(not included) for operation.
Adult assembly is required.
Tool required for assembly:
Phillips screwdriver (not included).
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembled Parts
Mobile
Arm
Base
Crib Connector
Note: All of the screws used to assemble this toy are attached to the product.
Follow these instructions carefully to fully secure the screws. Tighten and loosen
all screws with a Phillips screwdriver. Do not over-tighten.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Installation
1.5V x 3
"C" (LR14)
• Locate the battery compartment on the back of the base.
• Loosen the screws in the battery compartment door and lift to remove it.
• Insert three "C" (LR14) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically you may need to reset the electronics. Slide
the power/volume switch off and then back on.
• When sounds or motion become faint or stop, it's time for an adult to change the batteries.
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities
(Europe only).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
ICES-003 NMB-003
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit
pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre
le fonctionnement du dispositif.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Base
Crib Connector
1
• Fit the crib connector to the base, as shown.
IMPORTANT! Make sure the straps are over the top of the crib connector.
• Tighten both screws in the crib connector.
PRESS
SLIDE
Arm
Socket
2
• First press the button next to the socket and then slide the
socket door open
.
• Fit the arm into the socket in the base.
• Tighten both screws in the arm.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
P7866a-0920
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Bracket
Mobile
3
• Fit the mobile onto the bracket on the end of the arm.
• Tighten both screws in the mobile to secure it to the arm.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Crib Attachment
Base
Crib Top Rail
Straps
1
• Position the base so that the decorated side faces inside the crib.
• Fit the base onto the crib top rail, as shown.
• Make sure the top strap is hanging over the crib top rail. Pull the bottom strap through
the crib rails.
• Buckle the straps. Make sure you hear a "click". Pull on both ends of the strap to be
sure it's secure.
Tab
Tab
2
• Make sure the straps are tightened securely around the crib rail. Pull the free end of the
strap to tighten.
Hint: You can secure the free end of the strap to the base. Simply fit the free end of the
strap under the tabs.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Crib Attachment
3
• Tie the base strings to a crib spindle.
Note: It is better to tie the strings in a knot than a bow, since a bow may be easily untied.
At Least 7 Inchhes (118 cm)
4
• If the distance between the base and the mattress is less than 7 inches (18 cm), lower
the crib mattress.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Gentle Motion, Soothing Sounds & Classical Music
Sounds Button
Press for ocean sounds.
Music Button
Press for classical music.
Press the button again to
change the song.
Power/Volume Switch
Slide the switch to ON with
low volume
volume
or ON with high
. When finished using the
product, slide the switch OFF
.
Mode Select Switch
Slide the switch to:
Music only - plays sounds or
music for approximately 20 minutes.
Music and Motion - plays
approximately 12 minutes of music
while the mobile (when attached to
the base) sways from side to side.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Convert to a Music Box
Remove the mobile portion and use as a music box!
• Loosen both screws in the arm near
the base.
• Lift and remove the arm from the base.
• Close the small door on top of the base.
Store the mobile in a safe place for
future use.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
|