Fisher Paykel Dishwasher DD60D User Manual

(1,1) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM  
Installation instructions  
DishDrawer®  
NZ AU GB IE  
DD60D models  
Important!  
SAVE THESE INSTRUCTIONS  
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our  
local website listed at the end of this document or contact your local Fisher & Paykel dealer.  
1
SAFETY AND WARNINGS  
Important safety instructions!  
WARNING!  
Electrical shock hazard  
Installation of this DishDrawer® requires basic mechanical and electrical skills.  
Be sure to leave these Instructions with the Customer.  
Installation must comply with your local building and electricity regulations.  
At the completion of the DishDrawer® installation, the Installer must perform the Final Checklist.  
Remove all packaging materials supplied with the DishDrawer®.  
Before installing the DishDrawer®, remove the house fuse or open the circuit  
breaker.  
This appliance must be earthed. In the event of a malfunction or breakdown,  
earthing will reduce the risk of electric shock by providing a path of least  
resistance for electric current. This appliance is equipped with a cord having an  
equipment-earthing conductor and an earthing plug. The plug must be plugged  
into an appropriate outlet that is installed and earthed in accordance with all  
local codes and ordinances. WARNING- Improper connection of the equipment-  
earthing conductor can result in a risk of electric shock. Check with a qualified  
electrician or service representative if you are in doubt as to whether the  
appliance is properly earthed.  
This DishDrawer® is manufactured for indoor use only.  
Ensure all water connections are turned OFF. It is the responsibility of the plumber and  
electrician to ensure that each installation complies with all Codes and Regulations.  
The DishDrawer® MUST be installed to allow for future removal from the enclosure if service is required.  
The switched power outlet must be outside the DishDrawer® cavity, so that it is accessible after  
installation.  
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to  
the power supply cord.  
If the DishDrawer® is to be relocated from one installation to another it must be kept upright to avoid  
damage from water spillage.  
Do not modify the power supply plug provided with the appliance - if it will not  
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use  
an extension cord, adapter plug or multiple outlet box.  
Failure to follow this advice may result in electrical shock or death.  
Make sure only new hoses are used for connection (supplied with DishDrawer®). Old hoses should not  
be reused.  
Failure to install the DishDrawer® correctly could invalidate any warranty or liability claims.  
If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,  
boat or mobile facility containing the product to the service shop at your expense or pay the service  
technician’s travel to the location of the product.  
WARNING!  
Cut hazard  
Take care - panel edges are sharp.  
Failure to use caution could result in injury or cuts.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(2,1) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM  
4
PARTS SUPPLIED  
Clamp (1)  
Drain hose  
support (1)  
Drain hose  
joiner (1)  
Wire clip (2)  
Top  
Phillips  
Rubber  
Moisture protection  
tape (1)  
Hexagonal  
socket (2)  
Prefinished toekick (1)  
white or black  
mounting  
brackets (2)  
16 mm  
washer for  
inlet hose (1)  
screws (9)  
(to prevent moisture  
damage)  
(long & short)  
OPTIONAL  
If the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 3.6 m. The kit is available from the nearest  
Fisher & Paykel Authorised Service Centre or our local website listed at the end of this document.  
5
CAVITY PREPARATION  
Moisture protection  
tape must be applied.  
10 mm  
These marks indicate mounting bracket screw locations  
d
e
es can be locat  
vic  
r
e
Preferred position. If adequate clearance, services hole can be higher to  
clear toekick space.  
If hole is higher, ensure drain hoses are routed straight into the waste connection.  
e: S  
er®.  
w
Not  
either side of DishDra  
*
Water Connection  
Recommended COLD (Maximum 60°C).  
¾ “ BSP (GB20) to suit flat washer.  
Water Pressure  
Water softener models  
Other models  
Max  
1 MPa (145 psi)  
1 MPa (145 psi)  
Min  
0.1 MPa (14.5 psi)  
0.03 MPa (4.3 psi)  
Drains will need to be separated to satisfy kosher requirements.  
We suggest you confirm acceptability with your local rabbi in respect to kosher installations.  
max. 450 mm  
Water supply  
min. ø60 mm  
min. 200 mm  
*
*
220-240 VAC  
min. 9 A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(2,2) -1- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:15 AM  
Max. distance of  
hoses and cord from  
chassis edge  
Left hand Right hand  
side  
side  
Drain hose  
Left hand  
side  
Right hand  
side  
2000 mm  
1650 mm  
1650 mm  
1800 mm  
1250 mm  
1650 mm  
Inlet hose  
Power cord (excl. plug)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(1,1) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM  
6
A
ROUTE THE HOSES AND MOVE INTO THE CAVITY  
If top mounting brackets are being  
used, ensure they’re securely fitted  
before sliding product into cavity.  
A
B
Ensure hoses and cord  
are not kinked or twisted.  
2
optional  
(x2)  
3
Loosen feet only and  
take care when pushing  
the product into the  
cavity that you do not  
bend the feet.  
3
OR  
1
1
2
Tie together to avoid kinking.  
1
7
A
REMOVE THE DRAWER AND LEVEL THE PRODUCT  
B
Ensure product is level and aligning with cabinetry. Using the  
most appropriate length Hexagonal socket supplied, fully extend  
levelling feet up to required distance by hand.  
4
1
Ensure the drawer is removed and  
then rotated anti-clockwise  
to prevent kinked hoses.  
Hexagonal socket  
1
2
3
4
5
2
5
150 mm  
150 mm)  
(
3
5
x 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(1,2) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM  
8
SECURE THE PRODUCT AND REFIT THE DRAWER  
A
BB  
3
The product has three  
pairs of mounting  
brackets: a pair of  
optional brackets  
Ensure the drawer clips on  
both sides are reset.  
5
optional  
max. 19 mm  
C
C
on the top (C) and  
two pairs of formed  
brackets in the side of  
the chassis (A,B). Use  
at least two out of the  
three pairs to secure  
the product.  
Before refitting the drawer,  
ensure the hoses are not  
twisted and the latches at  
the rear of each drawer  
runner are facing forward.  
Ensure the sound  
insulation is  
repositioned  
correctly.  
4
4
B
B
A
Ensure the drawer is  
now rotated  
A
clockwise back.  
1
2
9
FIT THE TOEKICK  
A
B
4
5
6
7
Where the toekick  
meets the bottom  
of the tub is the  
cut-off point  
8
9
1
Important!  
D o not overtighten screw.  
2
10  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
(2,1) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM  
10  
PLUMBING AND DRAINAGE OPTIONS  
DishDrawer® using sink trap  
with drain hose joiner  
A
DishDrawer® and Standpipe Ø 38 mm  
B
2
2
Waste Disposal (optional)  
Do not connect to  
DishDrawer®  
If space is limited for fixing, push  
hoses through drain hose support  
to required height  
750-  
882.5  
mm  
750-  
882.5  
mm  
max.  
120  
mm  
1
38 mm  
1
HIGHLOOP  
min. 150 mm  
Waste Disposal  
(optional)  
Do not connect to  
DishDrawer®  
min.  
R 200 mm  
min. R 200 mm  
Supplied drain hose joiner  
19 mm waste tee  
3
3
4
Fit the supplied  
rubber washer  
Fit the supplied  
rubber washer  
Ensure hoses are routed  
straight to joiner.  
4
5
Remove excess hose  
material if necessary.  
180o  
180o  
5
6
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
(2,2) -2- 599684B DD60D installA2 NZGB.indd 6/7/09 11:49:38 AM  
11  
12  
TROUBLESHOOTING  
FINAL CHECKLIST  
Excessive water remaining above the filter plate, after the rinse cycle  
Check for kinked drain hoses or blocked waste connection, high loop not  
properly installed or drain hoses not routed correctly.  
No water supply ( shows on display-models with LCD only)  
Check water is connected, turned on and the spray arm(s) are correctly fitted  
and free to rotate.  
Check all parts are installed.  
Ensure product is level, securely fastened to the cabinetry and opens and closes  
freely. The DishDrawer® must be free to fully close with no resistance from the  
cabinetry.  
Ensure inlet hose to water supply has supplied rubber washer fitted and that it  
is tightened a further half turn after seal contact.  
No lights come on when the drawer is opened  
Ensure power is connected and is switched on. Check if Auto Power option is  
on.  
Ensure any knockouts or plugs in drain connection have been drilled out and  
drain connection has been made.  
The drain hose joiner must not support the weight of excess hoses. Keep hoses  
as fully extended as possible to prevent sagging. Any excess length of hose  
should be kept on the dishwasher side of the highloop.  
If using Plumbing and Drainage OPTION B, ensure the Highloop is a minimum  
150 mm higher than the drain hose joiner.  
Water around water supply and drainage connections  
Check connections, existing plumbing and hoses for leaks. Check rubber  
washer and hose clamps are correctly fitted.  
If product is tipping  
Ensure the product is secured to the cabinetry.  
Turn on the power and water supply. Then press the Power ( ) button to turn  
the DishDrawer® on. The DishDrawer® should beep and Wash Programme lights  
light up.  
If front panels are misaligned  
Check and relevel product. Check the cabinetry is square.  
Drawer(s) don’t close properly  
Check the spray arm is in place and free to rotate.  
Ensure nothing is obstructing the drawer(s) from closing properly eg sound  
insulation, hoses or drawer latches.  
Spray arm  
If a problem occurs, consult the Troubleshooting section of the User Guide.  
If after checking these points you still need assistance, please refer to the  
Service & Warranty book for warranty details and your nearest Authorised  
Service Centre, or contact us through our website, listed below.  
Add three cups of water into the DishDrawer®. On the Wash Programme  
Selector Panel press Rinse and close the drawer(s). Start the programme by  
pressing the Start/Pause ( ) button.  
After the Rinse programme has finished, ensure machine has run and drained  
correctly.  
Check water supply and drainage connection for leakage.  
Repeat for each drawer.  
599684B NZ AU GB IE 06.09  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Blower PB 265LN User Manual
Eizo Computer Monitor IEC60601 1 1 User Manual
Escient CD Player SE 160i User Manual
Extron electronic Network Card RGB 508 AKM User Manual
Extron electronic Stereo Receiver HFX 100 RX User Manual
Firstech LLC Remote Starter FT MB164 DC User Manual
Frigidaire Air Conditioner P N 66121617 User Manual
Frigidaire Microwave Oven FFMV162B User Manual
Furman Sound Stereo Amplifier MS2A 1 User Manual
GE Heat Pump AZ85H18DAC User Manual