Fisher Paykel Dishwasher DD605I User Manual

Integrated panel preparation  
DS605I and DD605I models  
DishDrawer  
NZ AU GB IE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Double models  
Product preparation  
2
4
Single models  
Product preparation  
Panel Installation  
Badge cut-out, handle and mounting bracket  
6
7
8
Securing the mounting brackets  
Reconnecting the wires and fitting the  
panels and a custom toe kick (double models only)  
Important!  
SAVE THESE INSTRUCTIONS  
The models shown in this User Guide may not be available in all markets and are  
subject to change at any time. For current details about model and specification  
contact your local Fisher & Paykel dealer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Product preparation  
Double DishDrawer models  
A
min.  
5 mm  
B
C
D
8 mm  
Air gap  
height of  
toe kick  
panel  
min.  
12 mm  
Installation diagrams for illustration purposes only  
The following calculations assume the top of the upper panel is aligned with the top of the  
adjacent cabinetry. The final panel/cabinetry alignment is achieved by adjusting the feet:  
width of ALL panels  
Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,  
then complete the equation.  
A
door clearance  
(min. 2.5 mm)  
width ALL panels  
door clearance panel width  
A
i.e 600 mm - 2 x 2.5 mm = 595 mm  
- 2 x  
+
=
=
(min. 595 mm)  
height of upper panel  
height  
height upper panel  
B
door extension  
standard height  
B
upper panel  
i.e 398 mm  
+
0 mm = 398 mm  
398 mm  
(0 mm recommended)  
(min. 595 mm)  
height of lower panel  
Measure C (door/drawer height (or equivalent)) and write it in the first box below,  
then complete the equation.  
height  
height  
height upper panel  
height lower panel  
C
C
upper panel  
lower panel  
i.e 717.5 mm - 398 mm - 8 mm = 311.5 mm  
Air gap  
-
- 8 mm =  
Air gap  
(min. 311.5 mm)  
(min. 717.5 mm + B)  
Note: The ‘door extension’  
B
allows for the top of the upper panel to be above the DishDrawer® where required.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Product preparation  
Toe kick preparation  
height of toe kick panel  
Measure D (height from the top of adjacent cabinet door fronts to the floor) and write it in the first  
box below, then complete the equation.  
height  
height  
toe kick panel  
D
B
D
B
toe kick panel  
i.e 817.5 mm - 0 mm - 735 mm - 12 mm = 70.5 mm  
-
- 735 mm - 12 mm =  
height adjacent  
door  
DishDrawer®  
min. clearance (min. 70.5 mm)  
cabinetry  
extension  
dimension  
Toe kick options  
The black prefinished toe kick panel is  
supplied. This panel can also have a front panel  
of your choice attached to it using screws or an  
adhesive.  
A toe kick panel of any material with thickness  
9 - 19 mm can be screwed to the plastic toe  
kick mounting bracket (supplied).  
432 mm  
55 mm  
Integrated Panel material  
67-127 mm  
max.  
67 mm  
16 -20 mm panel thickness  
Adequately sealed to withstand moisture (50OC @ 80% RH)  
Parts supplied  
Mounting  
bracket (2)  
Toe kick  
mounting  
screws (5)  
Panel mounting  
Integrated rectangular badge (2)  
screws (12)  
(Satin chrome supplied)  
Toe kick mounting  
bracket (1)  
Integrated door seal (2)  
Prefinished Toe kick panel (1)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Product preparation  
Single DishDrawer models  
A
min.  
5 mm  
B
9 mm  
Air gap  
9 mm  
Air gap  
Installation diagrams for illustration purposes only  
The following calculations assume the top of the panel is aligned with the top of the adjacent  
cabinetry:  
width of the panel  
Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,  
then complete the equation.  
A
door clearance  
(min. 2.5 mm)  
panel width  
door clearance panel width  
A
i.e 600 mm - 2 x 2.5 mm = 595 mm  
- 2 x  
=
(min. 595 mm)  
height of the panel  
Measure B (door/drawer height (or equivalent)) and write it in the first box below,  
then complete the equation.  
B
panel height  
panel height  
B
i.e 407 mm - 9 mm = 398 mm  
Air gap  
-
9 mm Air gap  
=
(min. 398 mm)  
Note: when the top of the DishDrawer® has to be lower than the adjacent cabinetry, the panel can be increased  
in height.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Product preparation  
.
el  
er® near floor lev  
w
a
ram if installing the DishDr  
se this diag  
U
9 mm  
Air gap  
9 mm  
Air gap  
Integrated Panel material  
16 -20 mm panel thickness  
Adequately sealed to withstand moisture (50OC @ 80% RH)  
Parts supplied  
Panel mounting  
screws (6)  
Integrated rectangular badge (1)  
(Satin chrome supplied)  
Mounting  
bracket (1)  
Integrated door seal (1)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Badge cut-out, handle and mounting bracket  
Installation diagrams feature double models for illustration purposes only  
1
Important!  
Ensure the product is not plugged in  
127 mm  
Badge z  
o
ne  
211 mm  
54 mm  
127 mm  
30 mm  
Badge z  
25 mm  
o
ne  
2
3
1
2
1
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Securing the mounting brackets  
3
1
2
4
2
16 mm x6  
1
Double models only:  
Important!  
Break off the tab at the top  
of the Lower Mounting Bracket  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Reconnecting the wires and fitting the panels  
and a custom toe kick (double models only)  
5
2
1
6
Important!  
Ensure the rubber seal between the  
drawer and panels is kept in place  
2
16 mm x 5  
1
1
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Copyright © Fisher & Paykel 2007. All rights reserved.  
The product specifications in this booklet apply to  
the specific products and models described at the  
date of issue. Under our policy of continuous product  
improvement, these specifications may change at any  
time. You should therefore check with your Dealer to  
ensure this booklet correctly describes the product  
currently available.  
NZ AU GB IE  
DishDrawer integrated panel preparation  
Published: 06/2007  
Part No. 529712 A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Blower PB 265L User Manual
Edelbrock Automobile Parts Torker II 440 User Manual
Eizo Computer Monitor EV2411W User Manual
Eizo Computer Monitor L461 User Manual
Elation Professional DJ Equipment DMX 512 User Manual
Field Controls Switch GSK 250M User Manual
Genesis Advanced Technologies Speaker Gen 928 User Manual
Genesis Advanced Technologies Speaker System G61 User Manual
GE Ventilation Hood PVB37 User Manual
Gianni Industries Door EM 1200 User Manual