564 SS / 564 E Rectangular Face
Black 95400411
Nickel 95400413
Compatibility:
• 564 SS Fireplace
• 564 Electric Fireplace
Packing List:
• Face
• 564 E Top and Bottom Brackets
• 564 E Top and Bottom Shims
• 564 E Upper Heat Shield
• (14) 8-32 Nuts
• (2) 564 SS Top Brackets (w screws)
• (2) 564 SS Upper Mounting Brackets
• (2) 564 SS Lower Mounting Brackets
• (2) 10-24 1-1/2" Screws (564 SS only)
The center deflectors must be in place when using this face to prevent
the facing above the fireplace from becoming too hot. If this face is
replacing a Lopi Grill (96200801), make sure to replace the center
deflectors.
Installation Details – 564 SS
36”
SIDE OF FIREPLACE
29”
1”
0” TO 1”
NOTE:
This face has an adjustable bracket that allows for
different facing depths to be tucked under the face.
Page 1 of 6
7/19/07
© Travis Industries, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
564 SS / 564 E Rectangular Face
Black 95400411
Nickel 95400413
Installation – 564 SS (continued)
2
The facing and hearth (if applicable) must be installed prior to attaching the face. See the installation
manual for complete details.
Raised
Fireplaces
Note how the tile is 1”
(maximum) above the
base of the fireplace.
Floor-Level
Fireplaces
Maximum 1`” Hearth
Page 3 of 6
7/19/07
© Travis Industries, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
564 SS / 564 E Rectangular Face
Black 95400411
Nickel 95400413
Installation – 564 SS (continued)
3
Install the face following the directions below.
Attach the upper brackets
to the face with the
included nuts.
a
The face is secured to the fireplace
Slide the face into place. The
tabs on the upper brackets insert
into the slots on the fireplace
brackets, holding the face in place
while the screws are tightened.
with four screws. Two of the screws
c
b
are fastened to the upper brackets
with press nuts. The lower screws
are included with the face.
Plated Surfaces
Denatured
Alcohol
Use denatured alcohol and a soft cloth to clean plated surfaces. Marks
left on the surface may damage the face.
Soft Cloth
Page 4 of 6
7/19/07
© Travis Industries, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
564 SS / 564 E Rectangular Face
Black 95400411
Nickel 95400413
Installation – 564 Electric
1
Install the upper heat shield onto the 564 E fireplace.
Place the upper heat shield included with this kit
on top of the fireplace (note position of heat
shield). Place the stock heat shield on top of it
and secure with the same screws.
Remove the stock upper heat shield.
Page 5 of 6
7/19/07
© Travis Industries, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
564 SS / 564 E Rectangular Face
Black 95400411
Nickel 95400413
2
Place the face, face down, on a soft, non-scratching surface. Install the 564 Electric mounting brackets onto
the back of the face.
Attach the upper 564 E
bracket (and shim). Use the
c
nuts included with this kit.
Attach the lower 564 E bracket (and
shim). Use the nuts removed earlier and
b
one of the nuts included with this kit.
Remove and
Repeat steps “a” through
discard the
d
“c” for the opposite side.
a
hinge assembly
from the face.
Before installing the
e
face verify the lower
grill is centered.
Loosen the nuts and
adjust if necessary.
3
Pull the electric fireplace out of the mantel (or built-in location). Attach the cove covers and face following the
directions below. Slide the fireplace back into place to complete the installation.
b
Lift the face up slightly, tilt
it forward and insert the
top hooks until the face
locks in place.
a
Tilt the face back slightly and
insert the bottom hooks into
the slots on the fireplace.
Page 6 of 6
7/19/07
© Travis Industries, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|