Owner’s Manual
Manual del Usuario
DVD3315V
DVD/CD Player
with Video Cassette Recorder
OPEN/
CLOSE
VCR
DVD
DISC IN
PLAY
REC
TIMER REC
VIDEO
STANDBY-ON REW
AUDIO
F.FWD STOP/EJECT PLAY
RECORD
SOURCE
PREV
STOP
PLAY
NEXT
IR
TRACKING
DVD PLAYER VCR
/
© 2009 Funai Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
CAUTION:
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’au fond.
FCC WARNING
This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause
harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority
to operate this apparatus if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This apparatus generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this apparatus does cause harmful interference
to radio or television reception, which can be determined by turning the apparatus off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the apparatus and receiver.
3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the
grounding system of the building as close to the point of cable entry as practical.
LASER SAFETY
This apparatus employs a laser. Only a qualified service person should remove the cover or attempt to service this
apparatus, due to possible eye injury.
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result
in hazardous radiation exposure.
CAUTION: Visible and invisible laser radiation when open and interlock defeated. Do not stare into beam.
LOCATION: Inside, near the deck mechanism.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates
copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
TRADEMARK INFORMATION
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from an AC outlet. Grasp it by the plug.
• Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
•
is a trademark of DVD Format/Logo Licensing
Corporation.
• Do not put your fingers or objects into the unit.
DEW CONDENSATION WARNING
LOCATION AND HANDLING
• Dew condensation may form inside the unit in the
following conditions. If so, do not use this unit at least
for a few hours until its inside gets dry.
• Do not install the unit in direct sunlight, near strong
magnetic fields, or in a place subject to dust or strong
vibration.
- The unit is moved from a cold place to a warm place.
• Avoid a place with drastic temperature changes.
• Install the unit in a horizontal and stable position.
Do not place anything directly on top or bottom of
the unit. Depending on your external devices, noise
or disturbance of the picture and/or sound may be
generated if the unit is placed too close to them. In this
case, please ensure enough space between the external
devices and the unit.
- Under conditions of high humidity.
- After heating a cold room.
NOTE ABOUT RECYCLING
• This unit’s packaging materials are recyclable
and can be reused. Please dispose of any
materials in accordance with your local
recycling regulations.
• Batteries should never be thrown away or
incinerated but disposed of in accordance with your
local regulations concerning chemical wastes.
• Depending on the environment, the temperature of this
unit may increase slightly. This is not a malfunction.
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Contents
PRECAUTIONS
ADVANCED PLAYBACK
Disc Menu· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16
Calling Up a Menu Screen During Playback· · · · · · · · · 16
Resume Playback · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16
MP3 Playback · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16
Zoom · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16
Camera Angles · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16
Stereo Sound Mode · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 16
Title, Chapter, Track, Folder or File Search · · · · · · · · · · 16
Index Search · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 17
Time Search · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 17
Repeat Playback · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 17
Repeat A-B Playback · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 17
Auto Repeat Playback· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 17
Programmed Playback· · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18
Random Playback· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18
Important Safeguards · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2
PREPARATION
Supplied Accessories · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4
About Cassette Tapes and Discs · · · · · · · · · · · · · · · · · · · 5
Playable Media · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
Unplayable Disc · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
Region Code · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
Color System · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
Function Overview · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 6
Remote Control · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 6
Front Panel · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 8
Rear Panel· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 9
Installing the Batteries for the Remote Control · · · · · · 9
Settings· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18
Connections · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10
Black Level Setting· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18
Virtual Surround · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 18
Subtitle Language and Audio Language· · · · · · · · · · · · 19
On-Screen Display · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 19
Connection to a TV · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10
Connection to an Audio System· · · · · · · · · · · · · · · · · · · · 12
Initial Setups · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 13
Turning on Unit for the First Time · · · · · · · · · · · · · · · · · · 13
Clock Setting · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 13
RECORDING
BASIC OPERATIONS
Recording & OTR (One-touch Timer Recording)· · · · · 20
Timer Recording· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 21
Note for Timer Recording & OTR · · · · · · · · · · · · · · · · · · · 21
Satellite Link· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 22
Dubbing a Cassette Tape · · · · · · · · · · · · · · · · · · · · · · · · · · 22
For VCR Playback · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 14
For Disc Playback · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 14
Hint for Disc Playback· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 15
Fast Forward / Fast Reverse Playback· · · · · · · · · · · · · · · 15
Still Mode / Step-by-step Playback · · · · · · · · · · · · · · · · · 15
Slow Forward Playback · · · · · · · · · · · · · · · · · · · · · · · · · · · · 15
To Skip the Titles, Chapters, Tracks, or Files · · · · · · · · · 15
To Reset the Cassette Tape Counter (Counter Reset) · · 15
To Rewind the Cassette Tape automatically
OPTIONAL SETTINGS
Changing the DVD Settings (in the setup menu) · · · 23
PARENTAL Setting · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 24
INITIALIZE · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 25
(Auto Rewind) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 15
TROUBLESHOOTING
Troubleshooting Guide · · · · · · · · · · · · · · · · · · · · · · · · · · 26
INFORMATION
Maintenance · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 27
Specifications · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 27
LIMITED WARRANTY· · · · · · · · · · · · · · · · · · · · · back cover
© 2009 Funai Electric Co., Ltd.
Supplied Accessories
All rights reserved. No part of this manual may be reproduced,
copied, transmitted, disseminated, transcribed, downloaded or
stored in any storage medium, in any form or for any purpose
without the express prior written consent of Funai. Furthermore,
any unauthorized commercial distribution of this manual or any
revision hereto is strictly prohibited.
remote control
(NB680UD)
RCA audio/video cables
(WPZ0102TM018 / WPZ0102LTE01)
Information in this document is subject to change without
notice. Funai reserves the right to change the content herein
without the obligation to notify any person or organization of
such changes.
with the
design is a registered trademark of Funai
Electric Co., Ltd and may not be used in any way without the
express written consent of Funai. All other trademarks used
herein remain the exclusive property of their respective owners.
Nothing contained in this manual should be construed as
granting, by implication or otherwise, any license or right to use
any of the trademarks displayed herein. Misuse of any trademarks
or any other content in this manual is strictly prohibited. Funai
shall aggressively enforce its intellectual property rights to the
fullest extent of the law.
owner’s manual
(1VMN27753)
Owner’s Manual
batteries
(AA x 2)
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
About Cassette Tapes and Discs
Playable Media
DVD-
VIDEO
Cassette
Tape
DVD-RW
DVD-R
DVD+RW
DVD+R
CD-DA
CD-RW
CD-R
Media Type
Logo
Symbols used
in this manual
AudioCD
MP3
DVD-Video
VHS
Recorded
Signal
analog
video
digital video (MPEG2)
digital audio or MP3
Unplayable Disc
Caution: Never play the following discs.
• DVD-RAM
• DVD-audio
• CD-i
• photo CD
• video CD
• DVD with region codes other than 1 or ALL
• HD DVD
• Blu-ray disc
• DTS-CD
• DVD-ROM for personal computers
• CD-ROM for personal computers
• the discs with labels, scratches, stains, blemishes, etc.
Caution: The sound may not be heard on the following disc.
• super audio CD
• Only the sound recorded on the normal CD layer can be delivered. The sound recorded on the high density super
audio CD layer cannot be delivered.
Note:
Any other discs without compatibility indications
• Unfinalized discs cannot be played back.
• For DVD-RW/R, discs recorded in the VR (video recording) format cannot be played back. Only the finalized video
format discs can be played back.
Note:
• Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or
special properties of discs.
• You can play back discs which bear the marks listed in “Playable Media”. If you use nonstandardized discs, this
unit may not play them back. Even if they are played back, the sound or video quality will be compromised.
• If the recorded portion of the disc is too small (less than 2-3/16 inches (55 mm) across), it may not play back
properly.
Region Code
Color System
This unit has been designed to play back DVD
with region 1. DVD must be labeled for ALL
regions or for region 1 in order to play back on
the unit. You cannot play back DVD that are
labeled for other regions. Look for the symbols
on your DVD. If these region symbols do not
appear on your DVD, you cannot play back the
DVD in this unit.
DVD is recorded in different color systems throughout the
world. The most common color system is NTSC (which is
used primarily in the United States and Canada).
This unit uses NTSC, so DVD you play back must be
recorded in the NTSC system. You cannot play back DVD
recorded in PAL color systems.
The number inside the globe refers to region of the world.
A DVD labeled for a specific region can only be played
back on the unit with the same region code.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Function Overview
Remote Control
Button names described in the Owner’s Manual
The instructions in this manual rest primarily on the premise that you will operate on the remote control (Please be
informed that some operations can only be made on the front panel of the unit).
VCR mode:
1
2
3
• Press to exit the VCR menu.
STANDBY-ON
OPEN/CLOSE
TRACKING
Pulse para salir del menú de VCR.
SPEED
TIMER SET
18
19
• Press to reset the cassette tape counter.
Pulse para restaurar el contador del casete.
1
4
2
5
8
3
6
9
6. DISPLAY
DVD mode:
p.19
¬
4
5
8
• Press to display the current disc mode.
Pulse para visualizar el modo de disco actual.
7
20
23
26
29
VCR mode:
CLEAR
INPUT
MODE
21
22
0
+10
• Press to display the current time, cassette tape
DISPLAY
VCR
DVD
6
7
counter, and L1 / L2.
Pulse para visualizar la hora actual, el contador del casete y L1 o L2.
7. VCR
(VCR) p.13
¬
24
PLAY
• Press to activate VCR mode.
Pulse para activar el modo de VCR.
STOP
25
27
28
30
31
32
9
10
8. E /
D
DVD mode:
p.15
¬
RECORD
TITLE
PREV
NEXT
PAUSE
AUDIO
11
SEARCH
• Press to search forward / backward through a disc.
Pulse para buscar hacia adelante o hacia atrás en el disco.
12
13
14
16
DISC MENU
SETUP
OK
• Press [D]to begin slow forward playback in the
pause mode. (DVD)
RETURN
A-B
ZOOM
ANGLE
Pulse [ D] para iniciar la reproducción lenta hacia adelante en el
modo pausa. (DVD)
15
17
SUBTITLE
REPEAT
VCR mode:
• Press to forward / backward a cassette tape.
33
Pulse para adelantar o retroceder un casete.
• Press [D] to begin slow forward playback in the
pause mode.
Pulse [ D] para iniciar la reproducción lenta hacia adelante en el
modo pausa.
9. PREV H (DVD) p.15
¬
• Press to go back to the previous chapters / titles.
(DVD)
Pulse para volver a los capítulos o títulos anteriores. (DVD)
• Press to go back to the previous tracks (CD) / files
1. TIMER SET (VCR) p.21
¬
(MP3).
• Press to put the VCR into standby mode for a timer
Pulse para volver a las pistas (CD) o archivos (MP3) anteriores.
recording.
10. RECORD (VCR) p.20
¬
Pulse para colocar el VCR en modo espera para una grabación
con temporizador.
• Press to start recording or press repeatedly to
activate the One-touch Timer Recording.
Pulse para comenzar a grabar o pulse reiteradamente para activar
la grabación rápida con temporizador.
2. SPEED (VCR) p.20
¬
• Press to select the recording speed.
Pulse para seleccionar la velocidad de grabación.
11. SEARCH p.16
¬
3. STANDBY-ON p.13
¬
DVD mode:
• Press to turn the unit ON / OFF.
• Press to search chapter / title (DVD).
Pulse para encender o apagar la unidad.
Pulse para buscar un capítulo o título (DVD).
• Press to search track (CD), or folder / file (MP3).
4. Number buttons (DVD) p.16
¬
Pulse para buscar una pista (CD), carpeta o archivo (MP3).
• Press to select chapter / title (DVD), track (CD), or
• Press to search time (DVD, CD).
folder / file (MP3) directly.
Pulse para buscar la hora (DVD, CD).
Pulse para seleccionar un capítulo o título (DVD), pista (CD), o
carpeta o archivo (MP3) directamente.
VCR mode:
• Press to call up the index or time search menu.
5. CLEAR p.13
¬
Pulse para visualizar el menú de búsqueda de hora o el índice.
DVD mode:
• Press to clear numbers entered incorrectly. (DVD,
12. TITLE (DVD) p.16
¬
CD, MP3)
• Press to call up the top menu on disc. (DVD)
Pulse para borrar los números ingresados incorrectamente.
(DVD, CD, MP3)
Pulse para visualizar el menú principal del disco. (DVD)
13. DISC MENU (DVD) p.16
¬
• Press to cancel the point for A-B repeat. (DVD, CD,
• Press to call up the disc menu on a disc. (DVD)
MP3)
Pulse para visualizar el menú del disco en un disco. (DVD)
Pulse para cancelar el punto para repetición de A-B. (DVD, CD, MP3)
• Press to clear all the tracks entered for
programmed playback. (DVD, CD, MP3)
Pulse para borrar todas las pistas ingresadas para la
reproducción programada. (DVD, CD, MP3)
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
14. SETUP p.23
27. PAUSE
F
p.15
¬
¬
DVD mode:
DVD mode:
• Press to call up the DVD menu.
• Press to pause disc playback.
Pulse para visualizar el menú de DVD.
Pulse para pausar la reproducción del disco.
VCR mode:
• Press to advance the playback one frame at a time.
• Press to call up the VCR menu.
(DVD)
Pulse para visualizar el menú de VCR.
Pulse para avanzar la reproducción un cuadro por vez. (DVD).
VCR mode:
15. ZOOM (DVD) p.16
¬
• Press to pause the playback / recording of a cassette
• Press to magnify part of a picture. (2x, 3x, 4x or 1/2x)
tape.
(DVD)
Pulse para pausar la reproducción o grabación de un casete.
Pulse para amplificar parte de una imagen. (2x, 3x, 4x ó 1/2x) (DVD)
• Press to advance the playback one frame at a time.
16. SUBTITLE (DVD) p.19
¬
Pulse para avanzar la reproducción un cuadro por vez.
• Press to select subtitles on a disc. (DVD)
28. AUDIO (DVD) p.19
¬
Pulse para seleccionar subtítulos en un disco. (DVD)
• Press to select audio languages on a disc. (DVD)
17. ANGLE (DVD) p.16
¬
Pulse para seleccionar idiomas de audio en un disco. (DVD)
• Press to select camera angles on a disc. (DVD)
• Press to select “STEREO” / “L-ch” / “R-ch”. (CD)
Pulse para seleccionar ángulos de la cámara en un disco. (DVD)
Pulse para seleccionar “STEREO”, “L-ch” o “R-ch”. (CD)
18. OPEN/CLOSE
DVD mode:
A
p.14
¬
29. OK (DVD) p.16
¬
• Press to confirm the items.
Pulse para confirmar los ítems.
• Press to open or close the disc tray.
Pulse para abrir o cerrar la bandeja del disco.
30. K / L / s /
B
p.16
¬
VCR mode:
DVD mode:
• Press to remove the videotape from the cassette
• Press to select items / settings.
compartment.
Pulse para seleccionar ítems o ajustes.
Presiónelo para retirar la cinta de video del compartimiento del
casete.
VCR mode:
K / L :
19. TRACKING
o
/
p
(VCR) p.15
¬
• Press to select an item on the VCR menu.
• Press either one of the buttons to stabilize the
picture manually if the picture begins to vibrate
Pulse para seleccionar un ítem en el menú de la VCR.
s :
vertically during the still mode.
• Press to go back one step during clock and timer
Pulse cualquiera de los botones para estabilizar la imagen de
forma manual si ésta comienza a vibrar de forma vertical durante
el modo pausa.
programming.
Pulse para retroceder un paso durante la programación del reloj y
el temporizador.
20. +10 (DVD)
B :
• Press to change title / chapter / track / folder / file
• Press to proceed to the next VCR menu.
Pulse para ir al siguiente menú de VCR.
number by 10 at a time.
Pulse para cambiar un título, capítulo, pista, carpeta o número de
archivo de 10 por vez.
31. RETURN
(DVD) p.18
¬
• Press to return to the previous operation in menu.
21. INPUT (VCR) p.20
Pulse para volver a la operación anterior en el menú.
¬
• Press to select input “L1” / “L2”.
32. A-B (DVD) p.17
¬
Pulse para seleccionar entrada “L1” o “L2”.
• Press to repeat between your chosen point of A and
22. MODE (DVD) p.18
¬
B. (DVD, CD, MP3)
• Press to set virtual surround ON / OFF.
Pulse para repetir entre los puntos de A y B que seleccionó. (DVD,
CD, MP3)
Pulse para apagar o encender sonido envolvente virtual.
• Press to set black level ON / OFF. (DVD)
33. REPEAT p.17
¬
Pulse para apagar o encender nivel de negro. (DVD)
DVD mode:
• Press to arrange the playing order or to perform
• Press to play back a chapter / title repeatedly. (DVD)
random playback. (DVD, CD, MP3)
Pulse para reproducir un capítulo o título reiteradamente. (DVD)
Pulse para organizar el orden de reproducción o para ejecutar la
reproducción aleatoria. (DVD, CD, MP3)
• Press to play back a track / disc repeatedly. (CD)
Pulse para reproducir una pista o disco reiteradamente. (CD)
23. DVD (DVD) p.14
¬
• Press to play back a file / folder / disc repeatedly.
• Press to activate DVD mode.
(MP3)
Pulse para activar el modo de DVD.
Pulse para reproducir un archivo, carpeta o disco reiteradamente.
(MP3)
24. PLAY
B
p.14
¬
VCR mode:
• Press to begin the playback of a disc / a cassette
• Press to select the repeat mode ON / OFF.
tape.
Pulse para encender o apagar el modo de repetición.
Pulse para comenzar la reproducción de un disco o casete.
25. STOP
C
p.14
¬
DVD mode:
• Press to stop disc playback.
Pulse para detener la reproducción del disco.
VCR mode:
• Press to stop the playback / recording of a cassette tape.
Pulse para detener la reproducción o grabación de un casete.
26. NEXT G (DVD) p.15
¬
• Press to skip chapters / titles. (DVD)
Pulse para saltar capítulos o títulos. (DVD)
• Press to skip tracks (CD) / files (MP3).
Pulse para saltar pistas (CD) o archivos (MP3).
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Front Panel
1 2
3
4 5
6
7 8
9
10
11
OPEN/
CLOSE
VCR
DVD
DISC IN
PLAY
REC
TIMER REC
VIDEO
STANDBY-ON REW
F.FWD STOP/EJECT PLAY
RECORD
SOURCE
PREV
STOP
PLAY
NEXT
IR
AUDIO
TRACKING
DVD PLAYER VCR
/
12
13 14 15 16 17 18
19
20
21 22 23 24 25
L2 input jacks
1. STANDBY-ONy p.14
• Press to turn on / off the unit.
2. Power on indicator
• Lights up when the unit is turned on.
3. cassette compartment (VCR) p.14
• Insert a cassette tape here.
4. REC indicator (VCR)
16. STOP C / EJECT A (VCR) p.14
¬
¬
C
STOP
:
•
Press to stop the playback / recording of a cassette
tape.
A
EJECT
:
¬
• Press to remove the cassette tape from the cassette
compartment.
17. PLAY B (VCR) p.14
¬
• Lights up during a recording, OTR (One-touch Timer
• Press to start the playback of a cassette tape.
Recording) or timer recording.
18. RECORD I (VCR) p.20
• Blinks when a recording is paused.
¬
• Press once to start a recording.
• Press repeatedly to activate an OTR (One-touch
Timer Recording).
5. TIMER REC indicator (VCR) p.21
¬
• Lights up when a timer recording or OTR (One-touch
Timer Recording) has been set.
• Blinks when a timer recording or OTR (One-touch
Timer Recording) has been finished or if the unit
could not complete the recording due to some error.
19. infrared sensor window p.9
¬
• Receive signals from the remote control so that you
can control the unit from a distance.
6. OPEN/CLOSE A (DVD) p.14
¬
20. TRACKING
o
/
p
(VCR) p.15
¬
• Press to open / close the disc tray.
7. VCR output indicator (VCR)
• Press either one of the buttons to stabilize the
picture if the picture begins to vibrate vertically
during the cassette tape playback.
• Lights up when the unit is in the VCR mode.
8. DVD output indicator (DVD)
• Lights up when the unit is in the DVD mode.
9. DISC IN indicator (DVD)
• Lights up when the disc is in the disc tray.
10. PLAY indicator (DVD)
21. SOURCE
• Press to switch to either DVD / VCR mode.
22. PREV H (DVD) p.15
¬
• Press to go back to the previous chapters / titles /
tracks / files during playback.
• Press and hold it to begin fast reverse search.
• Lights up when the inserted disc is being played
23. STOP C (DVD) p.14
back.
¬
• Blinks when an unplayable disc is inserted.
• Press once to stop disc playback temporarily.
11. Disc tray (DVD) p.14
24. PLAY B (DVD) p.14
¬
¬
• Place a disc when it is open.
• Press to start / resume playback.
12. VIDEO IN jack (VCR) p.22
25. NEXT G (DVD) p.15
¬
¬
•
Connect an RCA video cable from the video output
• Press to skip chapters / titles / tracks / files during
jack of your camcorder and other such devices here.
playback.
13. AUDIO IN jack (VCR) p.22
¬
• Press and hold it to begin fast forward search.
• Connect an RCA monaural audio cable from the
audio output jack of your camcorder and other such
devices here
.
14. REW E (VCR) p.15
• You can turn on the unit by pressing the buttons
¬
Note:
• Press to rewind the cassette tape or to view the
picture rapidly in reverse during playback (rewind
search).
6 or 24 (circled ones) or by inserting a cassette
tape.
• If you turn off this unit, [OPEN/CLOSE A] on the
remote control is not available. Be sure to use
15. F.FWD D (VCR) p.15
¬
• Press to rapidly advance the cassette tape or view
the picture rapidly in forward during playback
(forward search).
[OPEN/CLOSE A] or [STOP/EJECT
unit.
C
A] on the
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Rear Panel
1
2
DVD
DVD/VCR
AUDIO OUT
VCR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
OUT
OUT
AUDIO OUT
Y
L
AUDIO IN
VIDEO IN
L
C
C
B
R
L1
COAXIAL
VIDEO OUT
R
R
3 4 5 6 7 8
1. DVD/VCR AUDIO OUT jack p.10
7. DVD/VCR VIDEO OUT jack p.10
¬
¬
• Connect an RCA audio cable from here to the audio
input jack of your television or audio device. Standard
connection for DVD/VCR use.
• Connect an RCA video cable from here to the
VIDEO input jack of your television or audio device.
Standard connection for DVD/VCR use.
8. VCR VIDEO IN jack p.22
2. VCR AUDIO IN jack p.22
¬
¬
• Connect an RCA video cable from here to the video
output jack of your camcorder, VCR, etc.
•
Connect an RCA audio cable from the audio output
jack of your camcorder, VCR, etc. to here.
3. DIGITAL AUDIO OUT COAXIAL* jack p.12
¬
* For enhanced DVD viewing. DVD/VCR video and audio
connection required to view cassette tapes.
• Connect a digital audio coaxial cable from here
to the digital audio coaxial in jack of a decoder or
audio receiver.
4. DVD AUDIO OUT* (analog) jack p.11
¬
• RCA audio and video cables are included for
Note:
• Connect an RCA audio cable from here to the audio
both VCR and DVD viewing. You can enhance
your DVD picture and sound quality with an
S-video cable, component video cables, or a
digital audio coaxial cable. Please purchase
the necessary cables at your local store.
(Refer to pages 11-12.)
input jack of your television or audio device.
5. S-VIDEO OUT* jack p.11
¬
• Connect an S-video cable from here to the S-video
input jack of your television.
6. COMPONENT VIDEO OUT* jack p.11
¬
• Connect component video cables from here to the
component video input jacks of your television.
Installing the Batteries for the Remote Control
Install the batteries (AA x 2) matching the polarity
indicated inside battery compartment of the remote
control.
30˚ 30˚
16 feet (5m)
16 feet (5m)
23 feet (7m)
Caution: Never throw batteries into a fire.
Keep the following in mind when using the remote
control:
• Make sure that there are no obstacles between the
remote control and the infrared sensor window on the
unit.
• Do not mix different types of batteries together
Note:
(e.g., Alkaline and Carbon-Zinc) or old batteries
with fresh ones. Although they may look similar,
different batteries may have different voltages.
• If the remote control is not to be used for a long
period of time, remove the batteries to prevent
• The maximum operable ranges of the unit are:
damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can
overheat and rupture.
• Batteries should always be disposed of with
the environment in mind. Always dispose of
batteries in accordance with applicable laws
and regulations.
-
-
Line of sight: approx. 23 feet (7m)
Either side of center:
approx. 16 feet (5m) within 30°
-
-
Above:
Below:
approx. 16 feet (5m) within 15°
approx. 10 feet (3m) within 30°
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Connections
Connection to a TV
If Your TV Has Antenna in Jack Only
Before connecting, make sure the powers of the devices are turned off.
this unit
TV
VD
DVD/VCR
AUDIO OUT
VCR
VHF / UHF
antenna
COMPONENT
VIDEO OUT
O S-VIDEO
T
OUT
Y
L
AUDIO IN
VIDEO IN
L
C
C
B
R
R
VIDEO OUT
R
To audio L
VC
D
A
DVD/VCR
AUDIO OUT
output jack
DIGITAL
or
AUDIO OUT
ANT. IN
L
(White)
RCA
To audio R
audio cable
cable TV company
AUDIO IN
L
output jack
R
(Red)
RF coaxial
cable
COAXIAL
VIDEO OUT
VIDEO IN
RF coaxial cable
RF modulator (not supplied)
R
(Yellow)
To video
output jack
RCA video cable
3
4
L
R
TO TV CHANNEL
AUDIO IN
VIDEO IN ANT. INv
Set channel
3 or 4
rear of your RF modulator
(not supplied)
(White)
(Red) (Yellow)
To audio L
input jack
To audio R
input jack
To video
input jack
After making the connection illustrated above;
1) Set your RF modulator’s channel 3/4 switch to either 3 or 4, whichever the TV channel is least used in your area.
2) Turn on your TV and choose the same channel as you set the RF modulator’s channel 3/4 switch to.
• The quality of picture may become poor if this unit is connected to an RF modulator.
Note:
VCR and Basic DVD Connection
this unit
TV
DVD/VCR
AUDIO OUT
VCR
COMPONENT
VIDEO OUT
O S-VIDEO
OUT
Y
L
AUDIO IN
VIDEO IN
L
C
C
B
R
VIDEO OUT
R
R
To audio L
output jack
D
A
DVD/VCR
AUDIO OUT
VCR
DIGITAL
AUDIO OUT
To audio L
input jack
To audio R
input jack
(White)
To video
L
RCA audio cable
input jack
AUDIO IN
(Red)
L
(White)
(Red)
(Yellow)
B
R
To audio R
output jack
VIDEO OUT
R
(Yellow)
To video
output jack
RCA video cable
L
R
VIDEO
IN
AUDIO IN
• Connect this unit directly to your TV. If an RCA audio/video cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
Note:
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
EN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
After connecting to your TV:
You will need to switch to video input on your TV. This is usually marked TV/VIDEO, INPUT or AUX.
Please refer to your TV’s owner’s manual for details.
Input modes for common TV brands:
Listed below are inputs for common brand name TV’s.
Admiral:
Curtis Mathis: LINE1, LINE2,
00, 90, 91, 92, 93
AUX
KENWOOD:
LXI-Series:
Magnavox:
Panasonic:
RCA:
AUX
00
Samsung:
SANYO:
SHARP:
SONY:
TOSHIBA:
Zenith:
TV/VIDEO
VIDEO
00
VIDEO1, VIDEO2, VIDEO3
TV/GAME
00
AUX CHANNEL
TV/VIDEO
INPUT, TV/VCR, 00, 90, 91,
92, 93
GE:
INPUT, TV/VCR, 00, 90, 91,
92, 93
INPUT, AUX
VIDEO, VIDEO1, VIDEO2,
VIDEO3
HITACHI:
JVC:
Available on DVD Only
DVD/VCR
AUDIO OUT
VCR
TV
this unit
COMPONENT
VIDEO OUT
O S-VIDEO
T
OUT
Y
L
AUDIO IN
VIDEO IN
L
C
C
B
R
Basic Audio Connection
VIDEO OUT
R
R
L
R
AUDIO IN
A
DVD/VCR
AUDIO OUT
VCR
To audio L
To audio R
input jack
U
D
I
DIGITAL
inputt jack
UT
AUDIO OUT
(White)
(Red)
Y
L
AUDIO IN
VIDEO IN
To audio L
(White)
O
L
output jack
R
(Red)
VIDEO OUT
R
RCA audio cable
R
To audio R
output jack
and
Good Picture
DVD
DVD/VCR
AUDIO OUT
VCR
To S-video
input jack
S-VIDEO IN
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
OUT
OUT
AUDIO OUT
Y
L
S-video cable
AUDIO IN
VIDEO IN
To S-video
output jack
R
VIDEO OUT
R
R
V
I
D
E
O
or
To component
video Y output jack
Better Picture
DVD
DVD/VCR
AUDIO OUT
VCR
COMPONENT
VIDEO IN
COMPONENT
AUDIO S-VIDEO
VIDEO OUT
To component
DIGITAL
OUOUT
video Y input jack
(Green)
Y
To component
video CB output jack
Y
L
(Green)
AUDIO IN
CB
CR
L
component video cable
(Blue)
(Blue)
(Red)
C
B
R
To component
video CB input jack
R
(Red)
CR
To component
video CR output jack
To component
video CR input jack
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Connection to an Audio System
Playing Analog Audio
this unit
analog audio
input jacks
stereo system
D
O S-VIDEO
T OUT
DVD/VCR
AUDIO OUT
VCR
COMPONENT
VIDEO OUT
Y
L
AUDIO IN
VIDEO IN
L
C
C
B
R
AUDIO IN
VIDEO OUT
R
R
L
R
To audio L
output jack
DVD
DVD/VCR
AUDIO OUT
VCR
COMPONENT
AUDIO S-VIDEO
VIDEO OUT
TAL
O OUT
To audio L
input jack
To audio R
input jack
OUT OUT
L
(White)
(Red)
(White) (Red)
AUDIO IN
VIDEO IN
L
R
or
(White)
RCA audio cable
VIDEO OUT
R
(Red)
To audioR
output jack
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
Please purchase the rest of the necessary cables at your local store.
Playing Digital Audio
Dolby Digital decoder
digital audio receiver
this unit
S-VIDEO
OUT
DVD/VCR
AUDIO OUT
VCR
COMPONENT
VIDEO OUT
Y
L
AUDIO IN
VIDEO IN
C
B
R
VIDEO OUT
CR
digital audio
input jack
digital audio input jack
AUDIO OUT
VCR
DIGITAL AUDIO
COAXIAL IN
DIGITAL AUDIO
COAXIAL IN
NT
T
DIGITAL
or
AUDIO OUT
Y
L
To coaxial
output jack
AUDIO IN
VIDEO IN
L
To coaxial
input jack
To coaxial
input jack
B
R
COAXIAL
VIDEO OUT
R
BITSTREAM
PCM
digital audio coaxial cable
* You must select “BITSTREAM” or “PCM” in “DOLBY DIGITAL” setting. (Refer to page 23.)
Audio recording format of the disc
“Dolby Digital” setting of this unit
Actual output
2channel PCM
Dolby Digital
PCM
Dolby Digital
BITSTREAM
PCM
DVD-video
LPCM
2channel PCM
BITSTREAM
• The audio source on a disc in a Dolby Digital multi channel surround format cannot be recorded as digital sound
by an MD or DAT deck.
Note:
• Playing back a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
EN
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
Initial Setups
Turning on Unit for the First Time
Clock Setting
VCR
VCR
Press
first.
Press
first.
Please note: most instructions in this manual refer to
remote control use.
SETUP
Be sure your TV’s input is set to VIDEO. (Name may
vary with TV manufacturer. See your TV manual for
details.)
Press
and use
/
to select “CLOCK SET”.
1
1
2
Then press
to go to next step.
- M E N U -
TIMER PROGRAMMING
SATELLITE LINK
STANDBY-ON
AUTO REPEAT [OFF]
CLOCK SET
LANGUAGE SELECT
2
B
Press
.
• “LANGUAGE SELECT” menu appears.
• If the clock is not set yet, the “CLOCK SET” menu
Use
/
to select your on-screen language.
3
appears when you press SETUP . In this case, go to step 2.
Then press
to continue.
LANGUAGE SELECT
B
ENGLISH
FRANCAIS
ESPAÑOL
[ON]
Use
/
to select the contents to suit your
preference.
Then press
to go to the next item.
CLOCK SET
MONTH DAY
1 0 - -
YEAR
- - - -
/
When “CLOCK SET” menu appears,
go to step 2 in “Clock Setting” on this page.
4
HOUR MINUTE
AM/PM
- -
- -
:
- -
To Change the Selected On-screen Language
Use
/
to select “AM” or “PM”.
3
4
CLOCK SET
SETUP
Press
until the main menu appears.
1
2
MONTH DAY
1 0 0 7
YEAR
/
TUE 2 0 0 8
HOUR MINUTE
0 5 4 0
AM/PM
P M AM
B PM
:
Use
/
to select “LANGUAGE SELECT”.
to go to next step.
Then press
SETUP
Press
to exit the “CLOCK SET” menu.
Use
“ESPAÑOL”.
Then press
/
to select “ENGLISH”, “FRANCAIS” or
3
• To go back, press [s] during steps 2 to 3.
• Clock setting will be lost after a power failure, or
this unit has been unplugged for more than 30
seconds.
Note:
CLEAR
.
• If you accidentally select Spanish or French and
need English:
Note:
Press [SETUP] and choose
or SELECTION LANGUE . Press [B] and select
“ENGLISH”. Finally, press [CLEAR].
“SELEC. IDIOMA”
“
”
EN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
B
ASICPLAYBACK
Before: Turn on the TV.
For VCR Playback
For Disc Playback
(
page 16 for MP3 playback)
¬
STANDBY-ON
Insert a cassette tape so that the unit
will be turned on automatically.
Press
to turn on the unit.
OPEN/CLOSE
Then press
.
Inserte un casete para que la unidad se encienda
automáticamente.
STANDBY-ON
1 1
Para encender la unidad, pulse
.
Luego pulse OPEN/CLOSE
.
VIDEO
NEXT
TRACKING
• If the protection tab has
removed, playback will
start automatically.
VCR
Press
to switch to the VCR mode.
2
VCR
Insert a disc with its
label side facing up.
Inserte un disco con el lado
de la etiqueta hacia arriba.
Para cambiar al modo de VCR, pulse
.
2
VCR
• You need to press
every time you operate any
of VCR features.
first
• Depending on the disc, playback will start automatically
without pressing
• In case the DVD is recorded on both sides, make sure the
label of the side you want to playback is facing up.
.
PLAY
Press
to start
PLAY
playback.
Pulse
para comenzar la
DVD
PLAY
Press
to switch to the
3
reproducción.
DVD mode.
DVD
Pulse
para cambiar al modo
3
de DVD.
DVD
• You need to press
you operate any of DVD features.
first every time
STOP
Press
to stop the
playback.
STOP
Pulse
para detener la
reproducción.
4
4
Press
to start playback.
PLAY
PLAY
Pulse
para comenzar la reproducción.
For advanced playback, refer to the following pages.
STOP
Press
to stop the
• Time Search
• Auto Repeat
• Index Search
p.17
p.17
p.17
¬
¬
¬
playback.
STOP
Pulse
para detener la
5
reproducción.
• To prevent damage to the cassette tape, still
or slow mode will automatically stop after 5
minutes.
Note:
For advanced playback, refer to the following pages.
• Disc Menu
• Resume Playback
• Step-by-step Playback
• Repeat Playback
• Angle
p.16
p.15
p.16
p.16
p.16
p.18
p.16
¬
p.15
¬
p.17
¬
p.16
¬
p.18
¬
• To return to playback from the picture search,
¬
¬
¬
¬
¬
¬
• Still Mode
still or slow mode, press
.
PLAY
• MP3 Playback
• Zoom
• Search Functions
• Programmed Playback
• Random Playback
EN
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
• For DVD, set “STILL MODE” to “FIELD” in
Note:
Hint for Disc Playback
“DISPLAY” menu if pictures in the pause mode
are blurred. ( page 23.)
The contents of DVD are generally divided into “titles”.
Titles may be further subdivided into “chapters”.
The audio CD contains “track” and CD-RW/-R with MP3
contains “file”, which may be in a “folder”.
¬
• For VCR, to prevent damage to the cassette
tape, still mode will automatically stop after 5
minutes.
DVD-video
Slow Forward Playback
title 1
title 2
chapter 1 chapter 2 chapter 1 chapter 2 chapter 3
DVD
DVD-Video
Press
first.
Press [PAUSE F] during playback, then press [g]
repeatedly to select the desired forward speed.
Using [NEXT G] on this unit
Pressing and holding [NEXT G] on this unit in the still
mode will also change forward playback speed.
audio CD
track 3
track 1
track 2
file 2
track 4
track 5
file 3
Return to the normal playback, press [PLAY B].
VCR
VHS
MP3
file 1
Press
first.
folder 1
file 1
folder 2
file 2
Press [PAUSE F] during playback, then press [g].
([ F.FWD g] on this unit.)
• Press [g] or [h] ([ F.FWD g] or [REW h] on
this unit) to change the speed.
• If the distorting picture appears, you can adjust it by
Fast Forward / Fast Reverse Playback
K
L
using [TRACKING
/
].
Press [PLAY B] to return to the normal playback.
DVD
DVD-Video AudioCD MP3
Press
first.
• For DVD, slow forward speed is different
Note:
depending on the disc.
Press [g] or [h] repeatedly during playback to
select the desired forward or reverse speed.
Approximate speed is 1(1/32x), 2(1/16x), 3(1/8x),
4(1/4x) and 5(1/2x).
Using [PREV H], [NEXT G] on this unit
• For DVD, set “STILL MODE” to “FIELD” in
Pressing and holding [PREV H] or [NEXT G] on this
unit will also change forward or reverse playback speed.
“DISPLAY” menu if pictures in the slow forward
are blurred. ( page 23.)
Return to the normal playback, press [PLAY B].
¬
VCR
• For VCR, to prevent damage to the cassette tape,
slow mode will automatically stop after 5 minutes.
VHS
Press
first.
Press [g] or [h] ([F.FWD g] or [REW h] on this
To Skip the Titles, Chapters, Tracks, or Files
unit) during playback.
Return to the normal playback, press [PLAY B].
DVD
DVD-Video AudioCD MP3
Press
first.
• For DVD, audio CD and MP3, fast forward or fast
Note:
reverse speed is different depending on the disc.
Approximate speed is 1(2x), 2(4x), 3(8x), 4(16x)
and 5(32x).
Press [PREV H] or [NEXT G] during playback to skip
titles, chapters, tracks or files to a desired point.
Using [PREV H], [NEXT G] on this unit
Pressing [PREV H] or [NEXT G] on this unit will also
skip titles / chapters / tracks / files to a desired point.
• For VCR, press [g] again so the unit will search
at higher-speed. (in the SLP mode only.)
Still Mode / Step-by-step Playback
To Reset the Cassette Tape Counter
(Counter Reset)
DVD
DVD-Video AudioCD MP3
VCR
Press
first.
VHS
Press
first.
Press [PAUSE F] during playback.
Press [DISPLAY] to display the cassette tape counter on
the TV screen. Then, press [CLEAR] to reset the counter
to “0:00:00”.
DVD-Video
only
The picture goes forward by one frame each time you
press [PAUSE F] in the still mode.
• This function is not available if the unit begins
the timer recording or one-touch timer recording.
Note:
Return to the normal playback, press [PLAY B].
VCR
VHS
Press
first.
To Rewind the Cassette Tape automatically
(Auto Rewind)
Press [PAUSE F] during playback.
VCR
The picture goes forward by one frame each time you
VHS
Press
first.
press [PAUSE F] in the still mode.
• If the picture is distorted or rolling vertically, adjust the
vertical hold control on your TV if equipped.
When a cassette tape ends during playback, fast-forward
or normal recording, the unit will automatically rewind
to the beginning of the cassette tape. After rewinding
finishes, the unit will eject the cassette tape.
Return to the normal playback, press [PLAY B].
EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED PLAYBACK
Disc Menu
Zoom
DVD
DVD
DVD-Video
DVD-Video
Press
first.
Press
first.
Some discs contain menus which allow you to customize
DVD playback. Use [K / L /
press [OK] (or [PLAY B]).
1) Press [ZOOM] repeatedly to select the desired zoom
s
/
B] to select an item, then
factor: 2x, 3x, 4x, 1/2x.
2) Use [K / L /
s
/
B] to slide the zoomed picture across
the TV screen.
Calling Up a Menu Screen During Playback
3) To exit zoom mode, press [ZOOM] repeatedly.
DVD
DVD-Video
• Zoom function does not work while the disc
menu is displayed.
Note:
Press
first.
• Press [DISC MENU] to call up the disc menu.
• Press [TITLE] to call up the title menu.
Camera Angles
• Menu operations may vary depending on the
disc. Refer to the manual accompanying the disc
for details.
Note:
Some DVD may contain scenes which have been shot
simultaneously from the various angles. You can change
the camera angle if appears on the TV screen.
If the “ANGLE ICON” is set to “OFF” in “OTHERS” menu,
Resume Playback
will not appear. ( page 23.)
¬
DVD
DVD-Video AudioCD MP3
DVD
Press
first.
DVD-Video
Press
first.
1) Press [STOP C] during playback. Resume message will
1) During playback, press [ANGLE].
appear on the TV screen.
Each time you press [ANGLE], camera angle changes.
2) Press [PLAY B], playback will resume from the point
at which playback was stopped.
Stereo Sound Mode
• To cancel resume, press [STOP C] one more
time in the stop mode.
Note:
This unit allows you to select a sound mode during CD
playback.
• For MP3, playback will resume from where you
stopped (if the power has been turned off, the
playback will start from the beginning of the
track).
• The resume playback information stays on even
when the power is turned off, as long as the disc
stays in the unit.
DVD
AudioCD
Press
first.
1) During playback, press [AUDIO ].
Each time you press [AUDIO ], sound mode changes
as example below.
STEREO (right and left channels are active)
L-ch
R-ch
(left channel is active)
(right channel is active)
MP3 Playback
Insert a CD-RW/-R with MP3 files, the file list will
automatically appear on the TV screen.
Title, Chapter, Track, Folder or File Search
DVD
MP3
Press
first.
DVD
DVD-Video AudioCD MP3
Press
first.
1) Use [K / L] to select a desired folder from the list on
the left side in the file list.
1) Press [SEARCH] for the title, chapter, track, folder or
Then, press [PLAY B] or [OK].
file search.
2) Use [K / L] to select a desired file from the list on the
For the chapter search, press [B] to highlight
.
right side in the file list.
01/01
002/021
00:03:53
OFF
Then, press [PLAY B] or [OK].
3) Press [STOP C] once to stop MP3 playback
temporarily.
2) Use [the Number buttons] to enter the desired title,
• Depending on some sections, it may take a while
Note:
chapter, track, folder or file number within 5 seconds.
to be recognized.
3) Press [OK].
• Folders and MP3 files are displayed respectively
3
as and
.
• A maximum of 255 folders or 999 files may be
recognized on one disc.
• Up to 8 hierarchies can be recognized in one
folder. Files in the 9th or deeper hierarchies
cannot be played back.
• For MP3 file recorded in VBR (variable bit rate), the
unit may not display the actual elapsed time.
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED PLAYBACK
• To play back a double-digit track, press the track number
Repeat Playback
directly (e.g. for track 14, press [1], [4] and [OK]).
• To play back a triple-digit track, press the track number
directly for MP3. (e.g. for track 114, press [1], [1], [4] and
[OK]).
Repeat function is available only during playback.
DVD
DVD-Video AudioCD MP3
Press
first.
• Depending on the DVD being played back,
1) During playback, press [REPEAT].
Note:
this function can also be performed by directly
entering the desired chapter number with
[the Number buttons]. Refer to the manual
accompanying the disc.
• Each time you press [REPEAT], repeat function
changes as below.
(repeat off)
OFF
DVD-Video
• For DVD and audio CD, title, chapter or track
search is not available during programmed or
random playback.
(current chapter repeat)
CHAPTER
(current title repeat)
(repeat off)
TITLE
OFF
Index Search
VCR
AudioCD
VHS
Press
first.
(current track repeat)
TRACK
1) Press [SEARCH] once.
2) Use [K] or [L] to select a desired index number.
3) Press [s] to fast rewinding or [B] to fast forwarding.
(entire disc repeat)
(repeat off)
ALL
OFF
4) When the cassette tape has reached an index mark,
MP3
playback will start automatically.
(current file repeat)
(current folder repeat)
(entire disc repeat)
TRACK
GROUP
ALL
• The time gap between index marks must be more
than 1 minute for SP mode, 2 minutes for LP mode
and 3 minutes for SLP mode.
Note:
• The index search is not available during
recording.
• Press [STOP C] to stop the search.
• If a cassette tape ends during a search, the index
search will be canceled and the unit will rewind
to the beginning of the cassette tape.
• Repeat playback is not available with some discs
or during repeat A-B playback.
Note:
Repeat A-B Playback
DVD
DVD-Video AudioCD MP3
Time Search
Press
first.
1) During playback, press [A-B] at your desired starting
DVD
DVD-Video AudioCD
Press
first.
point as point A.
2) Press [A-B] at your desired ending point as point B.
3) Press [A-B] to exit the sequence so that “OFF” appears.
1) Press [SEARCH].
2) Press [B] once to highlight when operating audio CD.
Press [B] twice to highlight when operating DVD.
• Point B should be in the same title or track as
point A.
Note:
01/01
002/021
--:--:--
OFF
• To cancel point A, press [CLEAR] at step 1.
• Repeat A-B playback is not available with some
discs or during repeat playback.
3) Use [the Number buttons] to enter the desired time
within 5 seconds, then press [OK].
Auto Repeat Playback
Playback will start automatically.
VCR
The unit will automatically rewind the cassette tape when it
has reached the end and will automatically start playback
unless you press [STOP C] or you turn off the unit.
VHS
Press
first.
1) Press [SEARCH] twice.
VCR
2) Use [K / L] to select a desired time. Then, press [B] to
fast forward, or press [s] to fast rewind. When the
cassette tape is reached to the selected time, playback
will start automatically.
VHS
Press
first.
1) In stop mode, press [SETUP].
2) Use [K] or [L] to select “AUTO REPEAT“.
3) Press [
B] to “AUTO REPEAT” to set “ON” or “OFF”.
• For DVD, (e.g. to play time 0:15:00) press
Note:
4) Press [SETUP] to exit.
[1],[5],[0],[0] of [the Number buttons].
• For DVD and audio CD, press [CLEAR] to erase
the incorrect input at step 3.
• The auto repeat can also be set to “ON” or “OFF”
Note:
by pressing [REPEAT] on the remote control.
• To cancel auto repeat, follow step 1 above.
Then, press [B] so that “OFF” appears beside
“AUTO REPEAT”. Press [SETUP] to exit.
• The auto repeat playback will start
automatically if you select “AUTO REPEAT” to
“ON” in the stop mode.
• For VCR, press [STOP C] to stop the search.
• For VCR, if a cassette tape ends during a search,
the time search will be canceled and the unit will
rewind to the beginning of the cassette tape.
• The time search is not available for programmed
and random playback of a DVD or an audio CD
or during recording of the VCR.
EN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED PLAYBACK
• Up to 20 chapters, tracks or files can be ordered.
Note:
Programmed Playback
• To erase all the programs at once, select “ALL
CLEAR’’ and press [OK] or press [CLEAR] in
program input.
• The number of the title or chapter you enter
using [the Number buttons] cannot exceed
the maximum number of the chapters,tracks or
files on the disc.
• During the program playback, press [STOP C]
once to set the resume point, and then press
[PLAY B] to resume the program playback
from the beginning of the track where the
[STOP C] was pressed.
• During the program playback, press [STOP C]
twice to cancel the program playback. Your
programs are still stored until either the disc is
removed or power is turned off.
You can change the playback order of chapters / tracks / files.
DVD
DVD-Video AudioCD MP3
Press
first.
1) During playback, press [MODE] twice when operating
audio CD or MP3.
During playback, press [MODE] three times when
operating DVD.
2) Use [s] or [ B] to select “PROGRAM”. Then press [OK].
For DVD and MP3:
3) Use [K / L /
s
/
B] to select desired title (DVD) or
folder (MP3) input field.
DVD-PROGRAM
MAX
4
e.g. DVD
Total
0
TITLE CHAPTER PLAY ALL CLEAR
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
• Some DVD will not allow you to set
programmed playback.
• During programmed playback, “ TITLE” repeat
(DVD), and “ GROUP” repeat (MP3) are not
available.
4) Use [the Number buttons] to enter desired title
(DVD) or folder (MP3) number.
Random Playback
DVD-PROGRAM
MAX
4
Total
0
TITLE CHAPTER PLAY ALL CLEAR
This function shuffles the playing order of chapters/tracks/
files instead of playback in sequence.
03 --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
DVD
DVD-Video AudioCD MP3
Press
first.
1) During playback, press [MODE] twice when operating
audio CD or MP3.
During playback, press [MODE] three times when
operating DVD.
2) Use [s] or [ B] to select “RANDOM”. Then press [OK].
5) Press [OK], then use [the Number buttons] to enter
desired chapter number (DVD) or file number (MP3).
DVD-PROGRAM
MAX
4
Total
03
0
TITLE CHAPTER PLAY ALL CLEAR
• During random playback, you cannot go back
Note:
011
-- --- -- --- -- ---
to the previous track. Pressing [NEXT G]
allows you to search chapters, tracks or files
randomly.
--- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
-- --- -- --- -- --- -- ---
• During DVD random playback, you can play
back chapters in the current title randomly.
• Some DVD will not allow you to set random
playback.
6) Repeat steps 3 to 5 to enter another title and chapter
(DVD) or folder and file (MP3) numbers.
7) Use [K/ L/
s
/
B] to select “PLAY”, then press [OK].
For audio CD:
Settings
3) Use [K/ L/
s
/
B] to select desired track input field.
4) Use [the Number buttons] to enter desired track
Black Level Setting
number.
Adjust the black level to make the dark areas of the picture
brighter.
CD-PROGRAM
No.
MAX 14
Total
0
TRACK
PLAY ALL CLEAR
01 --
02 --
03 --
04 --
05 --
06 --
07 --
08 --
09 --
10 --
11 --
16 --
17 --
18 --
19 --
DVD
DVD-Video
Press
first.
12 --
13 --
14 --
15 --
1) During playback, press [MODE] once.
2) Use [s] or [ B] to adjust the black level.
ON: makes the dark areas brighter.
OFF: shows the original picture as recorded.
3) Press [RETURN ] to exit.
20
--
5) Repeat steps 3 to 4 to enter another track number.
CD-PROGRAM
MAX 14
Total
0
No.
TRACK
PLAY ALL CLEAR
01
05
06 --
07 --
08 --
09 --
10 --
11 --
16 --
17 --
18 --
19 --
Virtual Surround
02 --
03 --
04 --
05 --
12 --
13 --
14 --
15 --
You can enjoy stereophonic virtual surround on your 2
channel stereo system.
DVD-Video AudioCD MP3
20
--
DVD
Press
first.
6) Use [K/ L/
s
/
B] to select “PLAY”, then press [OK].
1) During playback DVD, press [MODE] twice.
During playback audio CD or MP3, press [MODE] once.
EN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED PLAYBACK
On-Screen Display
2) Use [s B] to select the desired sound mode.
/
3D:
sound mode suitable for setting
stereophonic audio
You can refer to the various information on the screen
when you press [DISPLAY].
JAZZ:
ROCK:
POP:
sound mode suitable for jazz music
sound mode suitable for rock music
sound mode suitable for pop music
DVD
Press
first.
:
t title number / total titles
DVD-Video
CLASSIC: sound mode suitable for classic music
OFF: no effects (original sound)
3) Press [RETURN] to exit.
elapsed time of the
current title
001/002
00:00:40
OFF
current repeat setting
• For audio CD, virtual surround will not be effective
Note:
1st
C(chapter):
DISPLAY
if the sound mode is set to something other than
“STEREO”. Refer to “Stereo Sound Mode”.
• When you connect the unit to a Dolby Digital
decoder with DIGITAL AUDIO OUT JACK, please
select “PCM” in “AUDIO” menu (Refer to p.12 for
details).
current chapter number /
total chapters
CH(chapter):
current chapter number / total chapters
remaining time
of the current chapter
001/002 00:00:19 - 00:01:11
NORMAL
2nd
elapsed time of the
current chapter
DISPLAY
Subtitle Language and Audio Language
This unit allows you to select a subtitle (if available) or an
audio language (if multiple languages are available for
audio language) during DVD playback.
TT(title):
current title number / total titles
remaining time of the
current title
03/24
00:00:20 - 00:01:09
NORMAL
DVD
DVD-Video
Press
first.
current play mode setting
3rd
elapsed time of the
current title
To Change the Subtitle Language
1) During playback, press [SUBTITLE].
PLAY
Each time you press [SUBTITLE] during playback, the
subtitle language changes as example below.
rmal display (display off)
ack):
OFF
ENG
FRE
(no subtitles)
AudioCD
nt track number / total tracks
(English subtitles)
(French subtitles)
01/26
00:00:11
OFF
current repeat setting
1st
elapsed time of the
current track
DISPLAY
2) To cancel the subtitle, use [B] or [s] to set subtitle to
remaining time
of the current track
“OFF“.
01/26
00:00:12 - 00:03:20
NORMAL
To Change the Audio Language
current play mode setting
2nd
3rd
elapsed time of the
1) During playback, press [AUDIO ].
DISPLAY
current track
Each time you press [AUDIO ] during playback, the
audio language changes as example below.
ALL:
current track number / total tracks
ENG
SPA
FRE
(English audio)
(Spanish audio)
(French audio)
remaining time of the
entire disc
01/26
00:00:14 - 01:11:28
NORMAL
elapsed time of the entire disc
DISPLAY
ormal display (display off)
• If your language is not shown after pressing
[SUBTITLE] or [AUDIO ] several times, the
disc may not have that language. However,
some discs allow subtitle/audio language
setting on the disc menu.
• When “ ” appears on the TV screen, it means
no subtitle/audio are recorded on the scene.
• Some discs will only allow you to change the
subtitle/audio language setting from the disc
menu.
Note:
rent folder number / total folders
MP3
current file number / total files
in the current folder
elapsed time of the current file
004/027
001/013
00:00:36
OFF
file name1
current repeat setting
3
1. folder1
2.
1. file name1
2. file name2
1st
DISPLAY
TR(track): current file number / total files in the current folder
elapsed time of the current file
remaining time of the current
file
• Operation varies depending on the disc, so refer
to the manual along with the disc for details.
001/013 00:00:43 - 00:03:36
NORMAL
file name1
3
current play mode setting
1. folder1
2.
1. file name1
2. file name2
2nd
DISPLAY
Normal display (display off)
EN
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
I
Before: Turn on the TV.
This unit has no tuner system so it cannot receive TV broadcasts without external tuner or such devices.
• You can also set the external tuner for timer recording. Refer to
Note:
“Satellite Link” on page 22.
• You CANNOT dub a DVD to a video cassette tape.
• Do not change the external tuner’s channel while you are recording.
TV
this unit
external tuner
You CANNOT watch one channel and record another at the same time.
Recording & OTR (One-touch Timer Recording)
STANDBY-ON
OPEN/
CLOSE
DVD
Press
to turn on the unit.
PREV
Then insert a recordable tape.
TRACKING
STANDBY-ON
Para encender la unidad, pulse
.
1
Luego inserte una cinta grabable.
• If the erase-protection tab has been
removed, cover the hole with clear tape.
VCR
Press
to switch to the VCR mode.
VCR
Para cambiar al modo de VCR, pulse
.
2
INPUT
Press
until “L1” or “L2” is displayed on
B
VCR
• You need to press
every time you operate any
of VCR features.
first
the TV screen. Select “L1” to activate rear
input jacks. Select “L2” to activate front
input jacks.
3
INPUT
Pulse
hasta que se visualice “L1” o “L2” en la
SPEED
pantalla de la TV. Seleccione “L1” para activar los
conectores posteriores de entrada. Seleccione “L2”
para activar los conectores frontales de entrada.
Press
to select the desired tape speed.
SPEED
Pulse
para seleccionar la velocidad deseada
SP
de la cinta.
4
• Connect your external tuner to the L1 (rear panel) jacks
of the unit. Connect camcorders and other such devices
to the L2 (front panel) jacks. Refer to pages 8, 9.
Tape speed
Recording / playback time
T60
T120
T160
Type of tape
SP mode
1hour 2hours 2-2/3hours
3hours 6hours
8hours
SLP mode
Press RECORD until desired
STOP
Press
to stop recording.
duration recording
REC
STOP
Pulse
para detener la grabación.
time is selected.
Pulse RECORD hasta que se seleccione
el tiempo de duración de grabación
deseado.
7
5
OPEN/CLOSE
Press
to eject the recorded
REC
(normal recording)
OTR (0:30)
OTR (1:00).....
cassette tape.
OTR (8:00)
OTR (7:30)
Pulse OPEN/CLOSE para expulsar el casete grabado.
8
To stop recording temporarily,
Accidental Erasure Prevention
To prevent accidental
recording, remove erase-
protection tab of the cassette
tape. To record again, cover
the hole with adhesive tape.
PAUSE
press
.
6
PAUSE
Para detener la grabación temporalmente, pulse
.
erase-protection tab
• During the recording in the pause mode, 5 marks appear on the
C
TV screen. Each mark represents 1 minute.
C
PAUSE
• Press
again to resume recording.
How to set the timer recording or satellite link,
refer to pages 21-22.
• Pause mode will be automatically canceled after 5 minutes to
prevent damage to the cassette tape and the video head.
EN
20
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
To Check, Correct or Cancel a Timer Program
Timer Recording
1) Press [TIMER SET], and then press [VCR ] on the
VCR
remote control.
VHS
Press
first.
2) Repeat procedures in step 1 above.
Press SETUP , use
“TIMER PROGRAMMING”.
/
to select
3) Use [K / L] to select the program number you want
to check. The details of the program you select will
appear on the TV screen.
1
Then, press
to go to next step.
- M E N U -
Use [s B] to go to the digit you want to change.
/
TIMER PROGRAMMING
Then, use [K / L] to enter the correct numbers.
B
TIMER PROGRAMMING
SATELLITE LINK
PROG 12345678
DATE
START TIME
AUTO REPEAT [OFF]
CLOCK SET
You can cancel the entire program by pressing [s
]
END
TIME
LANGUAGE SELECT
while the program number blinks.
L1/L2
REC SPEED
4) Press [CLEAR] to exit.
Available program
number blinks.
5) Press [TIMER SET] to return to the timer standby
mode.
PROGRAM NUMBER
DATE – – / – –
START TIME – – : – – – –
1
Use
/
to select an
2
3
To Cancel a Timer Recording in Progress
empty program number. Then,
END
L1/L2
REC
TIME – – : – – – –
– –
SPEED – –
Press [STOP/EJECT
C
A] on the unit.
press
to go to next step.
to select
Note for Timer Recording & OTR
Use
/
PROGRAM NUMBER
1
B
ONCE
• If there is no cassette tape in the unit or the cassette
tape does not have the erase-protection tab,
the [TIMER REC] indicator blinks and timer recording
cannot be performed.
“ONCE“, “DAILY“ (Mon-Fri), or
“WEEKLY“. Then, press
to go to next step.
DAILY
WEEKLY
ONE TIME PROGRAM
PROGRAM NUMBER
• If there is a power failure occurred or the unit is
unplugged for more than 30 seconds, clock setting and
all programmed timer recordings will be lost.
• If a cassette tape runs out before an OTR or a timer
recording is finished, the unit ejects the cassette tape.
Use
/
to select the
4
5
1
DATE
1 0 / 2 1 TUE
desired month. Then, press
to go to the next step.
START TIME – – : – – – –
END
L1/L2
REC
TIME – – : – – – –
– –
SPEED – –
Then, repeat procedures above to select the day, start
time, end time, and “L1” or “L2” as well.
After an OTR or a Timer Recording Has
Been Set, This Unit Operates as Follows:
ONE TIME PROGRAM
Use
/
to select
PROGRAM NUMBER
1
• Press [TIMER SET] on the remote control or [STOP/
DATE 1 0 / 2 1 TUE
CLEAR
START TIME 0 7 : 3 0 PM
END
L1/L2
REC
TIME 0 8 : 3 0 PM
recording speed. Then, press
.
EJECT
C
A] on the unit, then press [VCR ] to activate
L1
SPEED SP
the VCR function again.
B
SP
SLP
• To cancel the timer standby mode, press [TIMER SET] on
To set another program after step 5, press
.
the remote control or [STOP/EJECT
C
A] on the unit,
Then, repeat procedures from steps 2 through 5.
then press [VCR ] to activate the VCR function again.
You can program the unit to record up to 8 programs,
and up to 1 year in advance.
Press TIMER SET to set the timer standby mode.
When an OTR or a Timer Recording is Completed.
6
• If “AUTO POWER OFF” function for DVD has been
activated and some timer programming are left, the
[TIMER REC] indicator lights up and the unit goes to the
timer standby mode.
The [TIMER REC] indicator on this unit lights up and
the unit goes to the DVD mode.
• To go back one step, press [s] during steps 3 to
Note:
• The [TIMER REC] indicator blinks if there are no more
5.
timer programming.
• Select “L1” or “L2” to activate rear input jacks or
front input jacks accordingly.
• If auto power off for DVD has NOT been activated, the
unit goes to the DVD mode and all the VCR functions
will be unavailable. All the DVD functions are available
during OTR, timer standby mode and timer recording.
• Press [STOP/EJECT
C
A] on this unit or [TIMER SET]
on the remote control to use the VCR when the unit is
turned off.
To Use the DVD Player During Timer
Recording or While the [TIMER REC]
Indicator is On or Blinking.
• Press [STANDBY-ON] to turn on the unit. Press [DVD
on the remote control to choose DVD mode. Then
continue with the other DVD features as described in
this manual.
]
EN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
• Recording picture will be distorted if the copy
protection signal is being detected during
satellite link.
• When the timer recording and the satellite link
are overlapped, those recordings are recorded as
illustrated below.
Note:
Satellite Link
You can set the unit to start recording whenever it detects
a video signal from the external tuner.
Preparing for the Satellite Link:
• Only L1 (rear) is available for satellite link and be sure
that this L1 needs to be connected by the external tuner.
• The external tuner should be equipped with some kind
of timer function. Using timer function of the tuner, set it
to the output audio/video signals when it comes to the
time you want to start recording, and stop those signals
when it comes to the time you want to finish recording.
Refer to the tuner’s manual on how to set the timer.
e.g.) In case of the satellite link is overlapped on the exist-
ing timer recording.
timer recording
satellite link
recording result
e.g.) In case of the timer recording is programmed in the
middle of the satellite link.
L1
timer recording
satellite link
VCR
DVD
DVD/VCR
AUDIO OUT
VCR
external tuner
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
AUDIO IN
VIDEO IN
AUDIO OUT
OUT
OUT
To video out jack
Y
L
recording result
AUDIO IN
VIDEO IN
L
C
C
B
R
R
COAXIAL
VIDEO OUT
R
e.g.) In case of the timer recording is overlapped on the
To audio(L)out jack
RCA audio/video cables
existing satellite link.
timer recording
VCR
satellite link
VHS
Press
first.
recording result
SPEED
Press
to select the desired tape speed.
1
SP
Dubbing a Cassette Tape
SETUP
2
3
In the stop mode, press
.
Warning: Unauthorized recordings of copyrighted
cassette tapes may be an infringement of
copyright laws.
- M E N U -
Use
/
to select
TIMER PROGRAMMING
SATELLITE LINK
B
AUTO REPEAT
CLOCK SET
[OFF]
“SATELLITE LINK”. Then, press
to go to the next step.
LANGUAGE SELECT
front of the unit
output jacks of
VIDEO OUT
VIDEO
STANDBY-ON
AUDIO
R
external device
RCA video cable
RCA audio cable
SATELLITE LINK
4
Use
/
to select the
AUDIO OUT
or
0 1
:
0 0 PM
desired hour. Then, press
go to the next step.
to
L
L2
R
Then, repeat procedures above to select the minute
You can use a video disc player, cable/satellite box or
other devices with the audio/video output jacks.
as well.
The hour can be selected from 1-12 with AM or PM.
VCR
When the external tuner signal is stopped, recording
will be stopped.
VHS
Press
first.
1) Press [SPEED] on the remote control to select recording
Press
to set satellite
SATELLITE LINK
speed (SP or SLP).
5
link standby mode.
2) Press [INPUT] on the remote control to select L1 or L2
0 1
:
3 0 PM
[ON]
whichever the jack the external device is connected to.
3) Press [RECORD] on the unit, and then start playback of
the external device.
[TIMER REC] indicator: lights up and the unit goes to
the DVD mode. If you do not use DVD function, turn
OFF the unit.
An external tuner must be turned ON for satellite link
to start. If external tuner is not set to output signals,
satellite link will remain in standby mode.
4) To stop recording, press [STOP/EJECT
C
A] on this
unit.
5) Stop playback of the external device.
• For best results during dubbing, use buttons on
this unit whenever possible. The remote control
might affect another device’s operation.
Note:
To Cancel the Satellite Link on Standby:
Press [TIMER SET] on the remote control or
[STOP/EJECT
C
A] on this unit.
To Cancel the Satellite Link in Progress:
Press [STOP/EJECT
C
A] on this unit.
EN
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL SETTINGS
Changing the DVD Settings (in the setup menu)
In the setup menu, you can customize the various kinds of settings as you prefer.
Refer to the following instructions to navigate through the setup menus.
1) Press [SETUP].
2) Use [s B] to select a setup item.
/
3) Use [K/ L] to go up or down in the menu list.
4) Press [OK] to access the sub contents of the highlighted item.
5) Use [K/ L] to select a setting.
6) Press [SETUP] to exit.
• The following table is the contents which you can set and the default settings. Refer to the table for useful operation.
• Your change to each setting stays on even when the unit is turned off.
Setup menu (highlight is the default)
Contents
Notes
AUDIO
Set the language for • Language options are not available with some discs.
ORIGINAL
audio.
• Only the languages supported by the disc can be selected.
ENGLISH
FRENCH
SPANISH
• “LANGUAGE” setting for “AUDIO” and “SUBTITLE” are not
available with some discs. Then use [AUDIO ] and [SUBTITLE].
Refer to page 19.
•
•
•
OTHER
SUBTITLE
DISC MENU
Set the language for
subtitles.
OFF
ENGLISH
FRENCH
SPANISH
•
•
•
OTHER
Set the language for
disc menu language.
ENGLISH
FRENCH
SPANISH
•
•
•
OTHER
PLAYER MENU
TV ASPECT
Set the language for
OSD (on-screen
display).
ENGLISH
FRANÇAIS
ESPAÑOL
Set the picture size
according to aspect
ratio of your TV.
• Select “4:3 LETTER BOX” so that black bars may appear on the
top and bottom of the TV screen.
• Select “4:3 PAN & SCAN” for a full height picture with both sides adjusted.
• Select “16:9 WIDE” if a wide-screen TV is connected to this unit.
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
STILL MODE
Set the type of still
image in pausing
playback.
Select “AUTO”
usually.
• “AUTO” automatically selects the best resolution setting
(“FRAME” or “FIELD”) based on the data characteristics of the
pictures. Some pictures may be blurred when you select “AUTO”
in the still mode due to their data characteristics.
• An individual picture on the TV screen is called a “frame”, which
consists of two separate images called as “field”.
AUTO
FIELD
FRAME
• If you select “FIELD”, the picture in the still mode will be
stabilized. If you select “FRAME”, the picture in the still mode will
be highly defined.
DRC
Set to “ON” to
• This function is available only on the discs which are recorded in
the Dolby Digital format.
ON
OFF
(
Dynamic Range Control
)
compress the range
between soft and
loud sounds.
DOWN SAMPLING
DOLBY DIGITAL
Set to “ON” when
outputting in 48kHz.
Set to “OFF” when
outputting the
• When playing back a 96kHz disc with the copyright protection, or
when virtual surround is set to “1” or “2”, the sound will be down
sampled at 48kHz even if the “DOWN SAMPLING” is set to “OFF”.
• This function is available only on digital outputting of a disc
recorded in 96kHz.
ON
OFF
original sound.
Set the type of sound • Select “PCM” when the unit is connected to a 2ch digital audio
BITSTREAM
PCM
device.
signal which outputs
from the digital
audio output jack.
• Select “BITSTREAM” when the unit is connected to a Dolby
Digital decoder.
PASSWORD
LEVEL
Enter the password.
NO
YES
Set the parental level for DVD playback. (Refer to page 24.)
LEVEL8 [ADULT]
LEVEL7 [NC-17] to
LEVEL1 [KID SAFE]
CHANGE
Set and change the password. (Refer to page 24.)
Set whether to display the angle icon or not.
ANGLE ICON
ON
OFF
AUTO POWER OFF
Set to “ON” to turn off this unit automatically after 30 minutes of no use.
ON
EN
23
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL SETTINGS
DVD
Press
first.
CONTROL LEVELS
• Level 8:
DVD software of any grades (adult/
general/children) can be played back.
only DVD software intended for general
use and for children.
only DVD software intended for
children, with those intended for adult
and general use prohibited.
Press [STOP C] if you are playing back a disc.
• Levels 7 to 2:
• Level 1:
PARENTAL Setting
Parental setting will prevent your children from viewing
inappropriate materials (password protected). Playback
will stop if the ratings exceed the levels you set.
TIPS FOR LEVELS
• 8 [ADULT]:
DVD software of any grades (adult/
general/children) can be played back.
no one under 17 admitted
restricted; under 17 requires
accompanying parent or adult
guardian
parental guidance recommended
unsuitable for children under 13
parental guidance suggested
general audience
To Set the Parental Level
• 7 [NC-17]:
• 6 [R]:
SETUP
1
Press
to call up the setup menu.
2
3
Use
/
to select
.
• 5 [PGR]:
• 4 [PG13]:
• 3 [PG]:
• 2 [G]:
• 1 [KID SAFE]:
OK
Press
, and then use
/
to select “YES”.
When you use the unit for the first time, use
[the Number buttons] to enter the 4-digit number
for your password (except for 4737). Then, re-enter
the new password.
suitable for children
• Record the password in case you forget it.
• Some DVD-video may not respond to
“PARENTAL“ setting. Make sure this function
works with your DVD-video.
Note:
PASSWORD
NO
YES
- - - -
Enter password
• The resume information will be cleared if you
change the parental level when the resume
information is on.
• If you have set password already, use
[the Number buttons] to enter the current 4-digit
password.
To Change the Password
PARENTAL_CHANGE
Follow the step 1 to 3 in “To Set the Parental Level” on
1
2
PASSWORD
LEVEL
CHANGE
the left.
Enter password
- - - -
OK
Use
/
to select “CHANGE, then press
.
OK
PARENTAL_CHANGE
4
5
Use
/
to select “LEVEL“, then press
.
PASSWORD
LEVEL
CHANGE
PASSWORD
LEVEL
CHANGE
Use
OK
/
to select the desired level, then press
Use [the Number buttons] to enter the new 4-digit
password (expect for 4737). Then, re-enter the new
password.
3
4
.
PASSWORD
LEVEL
CHANGE
PASSWORD
LEVEL
CHANGE
8 [ADULT]
- - - -
Enter new password
SETUP
SETUP
6
Press
to exit.
Press
to exit.
• If you forget the password, press [4], [7], [3], [7],
then enter your new password.
Note:
Password will be cleared and parental levels will
be set to “LEVEL 8 [ADULT]”.
EN
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL SETTINGS
INITIALIZE
Reset the settings to factory default.
SETUP
1
Press
to call up the setup menu.
OK
2
3
Use
/
to select , then press
.
OK
Press
to select “YES”, then press
.
INITIALIZE_INITIALIZE
INITIALIZE
YES
1
2
3
4
Press
,
or
to select the desired language.
SELECT MENU LANGUAGE
ENGLISH
FRANÇAIS
ESPAÑOL
1
2
3
The next time you operate, the player menu language
will be the one you have selected.
EN
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Troubleshooting Guide
If this unit does not perform properly when operated as instructed in this manual. Refer to the following:
Symptom
Remedy
No power.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
This unit does not respond to the
remote control.
• Check if the power plug is connected to an AC outlet.
• You have to be within 23 feet (7m) of this unit.
• Check if a cassette tape or disc is in this unit.
Poor picture or noise.
• Interference signal may be received. Change the position and direction of the unit.
Cannot record a TV program.
• This unit does not have a tuner to receive TV broadcasting.
• You must connect this unit to TV with audio/video output jacks or an external tuner to
record TV programs. Refer to “Recording & OTR (One -touch Timer Recording)” on page 20
and “Satellite Link” on page 22.
Timer recording is impossible.
Cannot go into record mode.
Playback picture is partially noisy.
• Make sure the timer program is set correctly.
• Make sure [TIMER REC] indicator on this unit lights up. If not, press [TIMER SET].
• Make sure the VCR clock is set correctly.
• Make sure the cassette tape has a record tab. If needed, cover the hole with adhesive tape.
• Activate this unit in VCR mode. Press [VCR ] on the remote control so that the [VCR]
indicator will illuminate.
• Adjust tracking control for a better picture by pressing [TRACKING K / L].
Cannot view a picture but the audio • Head cleaning may be necessary. Refer to “Auto Head Cleaning” (page 27).
is OK.
No or poor, playback picture.
• Fine tune your TV.
• Connect the video cable firmly.
Video or color fades in and out when • You cannot copy a copyrighted cassette tape.
making a copy of a cassette tape.
Cannot remove the cassette tape.
• Check if this unit is in the VCR mode. If not, press [VCR ] on the remote control to switch
the mode.
No picture.
• Connect the video cable firmly.
• Insert a correct video disc that can be played back on this unit.
• Press [DVD ] on the remote control. Check if the [DVD] indicator will illuminate. Then try
other DVD features.
Disc cannot be played back.
• Insert the disc.
• Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
• Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on
its surface.
No sound.
• Connect the audio cables firmly.
• Turn on the power of the audio component.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output.
Distorted picture.
• This unit does not support DTS audio.
• Connect this unit directly to the TV.
• There are some cases where pictures may be slightly distorted, and those are not a sign of a
malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language does not • The selected language is not available for audio or subtitles on the DVD.
match the setting.
The camera angle cannot be
changed.
Audio or subtitle language
cannot be changed.
• The DVD does not always contain sequences recorded from different camera angles.
• The DVD does not always contain audio source or subtitles in the selected language.
• The operation is prohibited by this unit or the disc.
“
” appears on the TV screen,
prohibiting an operation.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this manual
for details on correct operations.
• Playback from a desired track and random playback are not available during programmed playback.
• Some functions are prohibited on some discs.
EN
26
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION
Maintenance
Servicing
Auto Head Cleaning
• Please refer to relevant topics on the “Troubleshooting
Guide” on page 26 before returning the product.
• If this unit becomes inoperative, do not try to correct the
problem by yourself. There are no user-serviceable parts
inside. Turn off, unplug the power plug, and please call
our toll free customer support line found on the back of
this manual to locate an authorized service center.
Cleaning the Cabinet
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol,
spirits, ammonia or abrasive.
• Automatically cleans video heads as you insert or
remove a cassette tape, so you can see a clear picture.
• If the playback picture is blurred or interrupted while
the TV broadcast is showing clear, the dirt may have
accumulated on the video heads, or the usage of rental
or worn cassette tapes can cause this problem. If a
streaky or snowy picture appears during playback, the
video heads in your unit may need to be cleaned.
1. Please visit your local audio/video store and purchase
a good quality VHS video head cleaner.
2. If a Video head cleaner does not solve the problem,
please call our toll free customer support line found on
the back of this manual to locate an authorized service
center.
Cleaning Discs
• When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center to out. Do not wipe
in a circular motion.
• Remember to read the instructions along with
the video head cleaner before use.
Note:
• Do not use solvents such as benzine, thinner,
commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for analog
records.
• Clean video heads only when problems occur.
IR Signal Check
• If the remote control does not work properly, you can
test if the remote control is sending out the infrared
signal with AM radio or a digital camera (including built-
in camera of cellular phone). It will help to define the
cause of malfunction.
Cleaning the Disc Lens
• If this unit continues to perform improperly even after
you have referred to the relevant sections and to the
“Troubleshooting Guide” in this manual, the laser optical
pickup unit may be dirty. Consult your dealer or an
authorized service center for inspection and cleaning of
the laser optical pickup unit.
Disc Handling
• When you handle a disc, hold it by its edge and try not
to touch the surface of the disc.
• Always store the disc in its protective case when not in
use.
• Do not glue paper or put stickers onto the disc. This may
damage the disc, and the unit may not read it correctly.
• With an AM radio:
Tune an AM radio to a station with no
broadcasting. Press a button on remote
control toward the radio. Sound will
be fluttering when you press any key
and the radio receives the signal. This
means the remote control is working.
• With a digital camera
(including built-in
camera of cellular phone):
Direct a digital camera to remote control,
press and hold a button on remote control.
If infrared light appears through digital
camera, the remote control is working.
Specifications
Output signal format: NTSC color
Recommended circumstances of recording MP3 files:
Sampling frequency:
Constant bit rate:
44.1kHz or 48kHz
32kbps ~ 320kbps
Video heads:
Tape width:
Tape speeds:
Rotary four-head
1/2 inch (12.65mm)
SP: 1-5/16 inch/sec. (33.40mm/sec)
LP: 16.67mm/sec.
SLP: 7/16 inch/sec. (11.12mm/sec.)
5 inches (12 cm) / 3 inches (8 cm)
Remote control:
Digital encoded infrared light system
Operating temperature: 41°F (5°C) to 104°F (40°C)
Power requirements:
120V AC +/- 10%, 60 Hz +/- 0.5%
Disc media size:
Terminals:
Component video output: RCA jack x 3
Power consumption (maximum):
21W
(standby: 3.8W)
Dimensions:
Weight:
W: 17 3/16” (435mm)
H: 3 3/4” (94mm)
D: 9 3/16” (233mm)
Y:
1Vp-p (75Ω)
Pb: 700mVp-p (75Ω)
Pr: 700mVp-p (75Ω)
Mini DIN 4-pin jack x 1
Approx. 5.8lbs (2.6kg)
S-video output:
Video output:
Y:
C:
1Vp-p (75Ω)
286mVp-p (75Ω)
RCA jack x 1 1Vp-p (75Ω)
• Designs and specifications are subject to change without notice.
• If there is a discrepancy between languages, the default language will
be English.
Coaxial digital audio output RCA jack x1 500mVp-p (75Ω)
Audio output:
Video input:
Audio input:
RCA jack x 4 2V rms
RCA jack x 2 1Vp-p (75Ω)
EN
27
RCA jack x 2 2V rms
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year
from the date of original retail purchase. Certain parts are excluded from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the
date of original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO
OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,
missing or if service was attempted by an unauthorized service center. This limited warranty does not
apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during
normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs,
alterations or products not supplied by FUNAI CORP., or damage, which results from accident, misuse,
abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use
such as hotel, rental or office use of this product, or damage which results from fire, flood, lightning or
other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL),
ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING
THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY
DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO
PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE
CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY
FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN
SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its
original packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE
CENTER. FUNAI CORP. will not reimburse you for any service done by unauthorized service providers
without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact us at:
FUNAI SERVICE CORPORATION
Customer Service
Tel: 1-800-317-6062
2200 Spiegel Drive, Groveport, OH 43125
E8KKSUD
1VMN27753 ★★★★★
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|