DRV_B2737_B2734.book Page 1 Thursday, March 31, 2005 10:04 PM
Owner’s Manual
DVD Recorder with Video
Cassette Recorder
DRV-B2737
DRV-B2734
OPEN/CLOSE
REW
FFWD STOP/EJECT PLAY RECORD
PROG.
DUBBING
SELECT
SELECT
STOP
PLAY RECORD
STANDBY-ON
VCR
DVD
S-VIDEO
VIDEO L(MONO)-AUDIO-R
Accessories Supplied
• Remote control
• RF cable
• Scart cable
• Owner’s Manual
• Quick Setup Guide
with two R6 (AA) batteries
Before using this unit you need to complete connections.
Refer to “Connections” on pages 16-17.
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 3 Thursday, March 31, 2005 10:04 PM
A NOTE ABOUT RECYCLING
Connection to Power
Before Switching on make sure that the voltage of
your electricity supply is the same as that indicated on
the rating plate.
This product’s packaging materials are recyclable
and can be reused. Please dispose of any
materials in accordance with your local recycling
regulations.
Mains Cord
When discarding the unit, comply
with your local rules or regulations.
Batteries should never be thrown
away or incinerated but disposed of
in accordance with your local
regulations concerning chemical
wastes.
This appliance may be fitted with a non-rewireable
plug. If it is necessary to change the fuse in a non-
rewireable plug the fuse cover must be refitted. If the
fuse cover is lost or damaged, the plug must not be
used until a replacement available from the appliance
manufacturer is obtained.
It is important that the colour of the replacement fuse
cover corresponds with the rating marking on the
base of the plug.
If the plug has to be changed because it is not
suitable for your socket, or becomes damaged, it
should be cut off and an appropriate plug fitted
following the wiring instructions below. The plug
removed must be disposed of safely as insertion into
a 13A socket is likely to cause an electrical hazard.
For your own safety read the following instructions
carefully before attempting to connect this unit to
mains.
Make your contribution to the environment!!!
• Exhausted batteries do not belong in
the dustbin.
• You can dispose of them at a collection
point for exhausted batteries or special
waste.
• Contact your council for details.
For Customer Use:
Carefully read the Model No. and Serial No.
located at the back of the unit and enter the
information below. Retain this information for
future reference.
The wires in this mains lead are coloured in
accordance with the following code:
Model No. _____________________
Serial No. _____________________
BLUE=NEUTRAL, BROWN=LIVE
Important
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:-
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or
coloured red.
No connection is to be made to the earth terminal of
the plug.
Installation Location
For safety and optimum performance of this unit:
• Install the unit in a horizontal and stable position.
• Do not place anything directly on top of the unit.
• Do not place the unit directly on top of the TV.
• Shield the unit from direct sunlight and keep away
from sources of intense heat. Avoid dusty or humid
locations. Avoid locations with insufficient ventilation
for suitable heat dissipation. Do not block the
ventilation holes on the sides of the unit. Avoid
locations subject to strong vibration or strong
magnetic fields.
If a 13 Amp (BS 1363) Plug is used, a 3 Amp Fuse
must be fitted, or if any other type of Plug is used a 3
or 5 Amp Fuse must be fitted, either in the Plug or
Adaptor, or on the Distribution Board.
Avoid the Hazards of Electrical Shock
and Fire
Mains Supply:220 - 240 V 50 Hz - AC only
• Do not handle the mains cable with wet hands.
• Do not pull on the mains cable to disconnect it from
AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug
the mains cable immediately and take the unit to an
Authorized Service Centre for servicing.
Do not make any connection to the larger pin marked
with the letter “E” or by the symbol
green or green and yellow.
or coloured
FUSE
BROWN
(Live)
Moisture Condensation Warning
BLUE
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
after heating a cold room, or under conditions of high
humidity. Do not use the unit for at least 2 hours to
allow the inside to dry.
(Neutral)
CORD GRIP
OUTER SHEATH OF THE WIRE
3
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 4 Thursday, March 31, 2005 10:04 PM
About Copyright
Maintenance
CLEANING THE UNIT
Use a soft cloth slightly moistened with a mild
detergent solution. Do not use solutions containing
alcohol, spirits, ammonia or abrasive.
Unauthorized copying, broadcasting, public
performance and lending of discs are prohibited.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly
is prohibited.
CLEANING DISCS
If a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the centre out. Do not wipe in a
circular motion.
Do not use solvents such as benzine, thinner,
commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for
analogue records.
Manufactured under licence from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
DISC HANDLING
Handle the discs so that fingerprints and dust do not
adhere to the disk surfaces.
Always store the disc in its protective case when it is
not in use.
Dolby Digital Recording
“Dolby® Digital Recording enables consumers to
record high-quality video with stereo sound on
recordable DVD discs. The technology, when
utilized instead of PCM recording, also saves
recordable disc space, allowing for higher video
resolution or extended recording time on each
DVD. DVDs created using Dolby Digital Recording
will play back on all DVD-Video players.”
Note: This is true when the players are compatible
with actual recordable DVD discs.
SERVICING
If the unit becomes inoperative, do not try to correct
the problem by yourself. There are no user
serviceable parts inside. Turn the unit off, unplug the
mains cable, and consult your dealer or an authorized
service centre.
CLEANING THE DISC LENS
If the unit does not perform correctly even though you
have referred to “Troubleshooting” and the relevant
sections in the Owner’s Manual, the laser optical
pickup unit may be dirty. Consult your dealer or an
authorized service centre for inspection and cleaning
of the laser optical pickup unit.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
“Kodak Picture CD COMPATIBLE” is a trademark
of Eastern Kodak Company.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt
accumulated on the video heads after a long period
of use, or the usage of rental or worn tapes can
cause this problem. If a streaky or snowy picture
appears during playback, the video heads in the unit
may need to be cleaned.
1. Please visit your local Audio / Video store and
purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the
problem, please consult your dealer or an
authorized service centre.
Note:
• Remember to read the instructions along with the
video head cleaner before use.
• Clean video heads only when problems occur.
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 5 Thursday, March 31, 2005 10:04 PM
Table of contents
Before you start...................................... 2
Precautions ........................................................... 2
Features................................................................ 6
Guide to the Owner’s Manual................................ 7
Functional overview .............................................. 8
Installing batteries in the remote control ............. 12
VCR / DVD recorder Switching ........................... 12
Guide to On Screen Displays.............................. 13
Front Panel Display Guide .................................. 15
Changing the Setting menu.................57
Tour of the Setting menu..................................... 57
Language setting................................................. 58
Display setting ..................................................... 59
Audio setting........................................................ 59
DVD-Videos Parental lock level........................... 61
Changing Video Out system................................ 62
VCR functions.......................................63
Playback.............................................................. 63
Getting Started ..................................... 16
Connections ........................................................ 16
Channel setting ................................................... 18
Setting the clock.................................................. 20
Selecting the TV aspect ratio .............................. 21
Recording and one-touch timer recording
(OTR)................................................................... 63
Search ................................................................. 64
Other operations.................................................. 65
Hi-Fi Stereo Sound System................................. 65
Others....................................................66
Troubleshooting................................................... 66
Language code.................................................... 70
Glossary .............................................................. 71
Specifications ...................................................... 72
Declaration of Conformity...................... Back cover
Recording ............................................. 22
Information on DVD recording............................. 22
Formatting a disc................................................. 24
Selecting the Sound mode.................................. 25
Basic recording ................................................... 26
One-touch timer recording (OTR) ....................... 27
Timer recording .................................................. 28
PDC (Programme Delivery Control).................... 30
Settings for external equipment .......................... 32
Dubbing Mode..................................................... 33
Setting a disc to protect ...................................... 34
Finalising discs ................................................... 34
Playing back discs............................... 36
Information on playing back DVDs...................... 36
Basic playback .................................................... 37
PBC function for Video CDs................................ 40
Special playback ................................................. 41
Search................................................................. 43
Repeat / Random / Program playback /
Slide Show .......................................................... 45
Selecting the format of audio and video.............. 46
Editing................................................... 48
Disc editing.......................................................... 48
Editing discs in Video mode................................ 48
Editing discs in VR mode .................................... 51
Editing Original titles in VR mode........................ 51
Editing the Playlist in VR mode........................... 53
5
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 6 Thursday, March 31, 2005 10:04 PM
Quick search:
You can easily find the part you want to watch using
the search function. Search for a desired point on a
disc by title, chapter or time.
Features
This unit not only plays back DVDs, CDs and VHS
tapes but also offers features for you to record to DVD
discs and edit them after that. The following features
are offered with this unit.
Playback from Original or a Playlist (VR mode):
You can play back titles using either the Original list or
a Playlist.
VCR mode
Recording
The unit is compatible with DVD-RW discs, which are
recordable repeatedly, and DVD-R discs, which are
recordable only once.
Also, this unit allows you to record to the video
cassette tape. You can choose either one for your
convenience.
Quick search for what you want to watch:
You can easily find the part you want to watch using
the Index or Time search functions. An index mark will
be assigned at the beginning of each recording you
make. For Time search function, you can go to a
specific point on a tape by entering the exact amount
of time you wish to skip.
DVD mode
VCR mode
Recording up to 8 programme:
Editing
You can programme the unit to record up to 8
programmes, up to a month in advance. Daily or
weekly programme recordings are also possible.
DVD mode
Set / clear chapter markers (VR mode):
You can easily add chapter markers anywhere in your
recordings for easy editing. (Playlist only)
One-touch timer recording:
You can set your required recording time easily. Every
time [REC / OTR] is pressed during recording, the
recording time will be increased by 30 minutes up to 8
hours. The recording automatically stops when the
recording time you set is finished.
Making your own Playlist (VR mode):
While the Original list remains unchanged, you can
edit titles as you prefer and create your own Playlist.
Edit title names
Dubbing mode:
Set thumbnail pictures
You can copy a DVD disc to a videotape or copy a
videotape to a DVD disc. This function will be
available only if the DVD disc and the videotape are
not copy protected.
Set / clear chapter markers
Divide / combine titles
Delete parts of titles
Protecting titles (VR mode):
Left channel stereo recording:
To avoid accidental editing or erasing of titles, the
protect function is useful when set to “ON” in the
original list.
This unit can record the sound of the Left channel
monaural input as Left and Right channels
automatically (available only for AV3 jacks on the front
panel).
Compatibility
DVD mode
DVD mode
REC MONITOR:
Playing back discs recorded in Video mode on
any regular DVD player:
Discs recorded in Video mode can be played back on
regular DVD players, including computer DVD drives
compatible with DVD-Video playback. You will need to
finalise the discs recorded in Video mode to play back
in other DVD players.
You can confirm the picture and sound recording
quality for the recording speed you have currently set.
Automatic Chapter marker setting:
Chapter markers will be added to recordings as you
set them in the Setting menu before starting to record.
Automatic Title menu making (Video mode):
The unit creates title menus automatically when
finalising discs.
* DVD-Video Format (Video mode) is a new format for
recording on DVD-RW / R discs that was approved by
the DVD Forum in 2000. Adoption of this format is
optional for manufactures of DVD playback devices
and there are DVD-Video players, DVD-ROM drives
and other DVD playback devices available that cannot
play back DVD-RW / R discs recorded in the DVD-
Video Format.
Automatic Playlist making (VR mode):
The unit creates a Playlist automatically after
recording.
Automatic finalising (Video mode):
You can finalise discs automatically at the end of the
disc space if you set this in the Setting menu.
PDC:
Playback
This system assures that the TV programme you wish
to record using timer recording will be recorded
exactly from beginning to end even if the actual
broadcasting time differs.
DVD mode
Theatre surround sound:
When the unit is connected to an amplifier or a
decoder compatible with Dolby Digital or DTS, you
can enjoy theatre-quality surround sound from discs
recorded with the surround sound system.
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 7 Thursday, March 31, 2005 10:04 PM
Guide to the Owner’s Manual
Symbols used in the Owner’s Manual
To show what recording mode or disc type applies to
each function, the following symbols appear at the
beginning of each operating item.
Symbol
Description
Available for DVD-Videos
DVD-V
Video
DVD-RW
Available for DVD-RW discs in
Video mode
VR
DVD-RW
Available for DVD-RW discs in VR mode
Available for DVD-R discs in Video mode
Available for DVD+RW discs*
Available for DVD+R discs*
DVD-R
DVD+RW
DVD+R
CD
Available for Audio CDs
Available for Video CDs
VCD
Available for CD-RW / R discs with
MP3 files
MP3
Available for CD-RW / R discs with JPEG
files
JPEG
VCR
Available to VHS tapes
Use only cassettes marked VHS .
* There may be a disc which cannot be used or played
back.
Button names described in the
Owner’s Manual
The instructions in this manual are described mainly
with the operations using the remote control. Some
operations can be carried out using the buttons on the
front panel.
7
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 8 Thursday, March 31, 2005 10:04 PM
Functional overview
Front panel
1
2
3*
4
5
6 7
OPEN/CLOSE
DUBBING
REW
FFWD STOP/EJECT PLAY RECORD
PROG.
SELECT
SELECT
STOP
PLAY RECORD
STANDBY-ON
VCR
DVD
S-VIDEO
VIDEO L(MONO)-AUDIO-R
20* 19* 18 17*16 15
141312 11 10* 9*
8
*You can also turn the unit on by pressing these buttons.
1
STANDBY-ON button
• Press to turn on or off the unit.
• Red LED Lights up when power is ON.
12 SELECT LPbutton (DVD / VCR)
• Press to select the DVD mode or the VCR
mode.
2
3
4
5
Cassette compartment (VCR)
• Insert a tape here.
13 DUBBING button (DVD / VCR)
• Press to start VCR to DVD (DVD to VCR)
duplication which you set in the setting menu.
OPEN / CLOSE O button* (DVD)
• Press to open or close the disc tray.
14 PROG. U / D buttons (DVD / VCR)
• Press up or down to change the channel.
Disc tray (DVD)
• Place the disc on here when open.
15 Display (DVD / VCR)
• Refer to “Front Panel Display Guide” on
page 15.
S-VIDEO input jack (AV3) (DVD / VCR)
• Use to connect the S-Video output of external
equipment with an S-Video cable.
16 RECORD
button (VCR)
• Press once to start recording.
• Press repeatedly to start a one-touch timer
recording.
6
7
8
VIDEO input jack (AV3) (DVD / VCR)
• Use to connect external equipment with a
standard Video cable.
17 PLAY P button* (VCR)
• Press to start playback.
AUDIO input jacks (AV3) (DVD / VCR)
• Use to connect external equipment with
standard Audio cables.
18 STOP / EJECT SO button (VCR)
• Press to remove the tape from the unit.
• Press to stop the tape motion.
• Press to stop the proceeding timer recording in
VCR.
RECORD
button (DVD)
• Press once to start recording.
• Press repeatedly to start a one-touch timer
recording.
19 FFWD f button* (VCR)
• Press to rapidly advance the video tape.
• Press to view the picture rapidly in forward
during playback. (Forward Search)
9
PLAY P button* (DVD)
• Press to start or resume playback.
• Press to turn the unit on when the video tape is
inserted and start rapidly advancing the tape.
10 STOP S button* (DVD)
• Press to stop a playback or recording.
• Press to stop a timer recording of DVD.
20 REW r button* (VCR)
• Press to rewind the video tape.
11 VCR / DVD SELECT indicator
• Indicates the selected component (VCR or
DVD).
• Press to view the picture rapidly in reverse
during the playback mode. (Rewind Search)
• Press to turn the unit on when the video tape is
inserted and start rewinding the tape.
Button names described in the Owner’s Manual
The instructions in this manual are described mainly with the operations using the remote control. Some
operations can be carried out using the buttons on the front panel.
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 9 Thursday, March 31, 2005 10:04 PM
Rear Panel
DVD/VCR
AV2(DECODER)
DVD
AUDIO
OUT
DVD/VCR
AERIAL
DIGITAL
S-VIDEO
OUT
AUDIO OUT
OPTICAL COAXIAL
L
AV1(TV)
RF OUT
R
1
2 3
4 5 6 7 8
*The unit is for the DRV-B2737.
1
2
Mains cable
• Connect to a standard AC outlet.
5
6
AUDIO OUT jacks (DVD)
• Connect to the audio input jacks on your TV.
Use commercially available Audio cables.
AV2 (DECODER) (DVD/VCR)
• Connect to VCR, camcorder, or other
Audio-Video equipment. Use a commercially
available Scart cable.
S-VIDEO OUT jack (DVD)
• Connect to the S-Video input jack on your TV.
Use commercially available S-Video cable.
3
4
AV1 (TV) (DVD/VCR)
• Connect to the Scart jack on your TV. Use the
supplied Scart cable.
7
8
AERIAL (DVD/VCR)
• Connect to an antenna or cable.
RF OUT (DVD/VCR)
DIGITAL AUDIO OUT (DVD) (OPTICAL
• Connect to the Aerial jack on your TV, cable box
or direct broadcast system. Use the supplied RF
cable.
(DRV-B2737 only), COAXIAL) jacks
• Connect to an amplifier with digital input jacks
such as a Dolby Digital decoder or DTS
decoder. Use a commercially available optical or
coaxial cable.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage
to the unit.
• This unit does not have an RF modulator.
9
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 10 Thursday, March 31, 2005 10:04 PM
Remote Control
5
6
TOP MENU button (DVD)
• Press to display the top menu.
OPEN/CLOSE
/EJECT
STANDBY-ON
MENU / LIST button (DVD)
T-SET TIMER PROG.
17*
18
1
2
• Press to display the Disc menu during palyback.
• Press to change the Original and Playlist on the
TV screen. (VR mode only)
@
.
/:
ABC
2
DEF
3
1
PROG.
REPEAT
SETUP
GHI
4
PQRS
7
JKL
5
TUV
8
MNO
6
WXYZ
9
19
3
7
8
Cursor U / D / L / P buttons (DVD / VCR)
• Press to select items or settings.
20
21
22
23
24
DISPLAY SPACE
0
CLEAR
4
VCR
button
TOP MENU MENU/LIST RETURN ENTER
• Press to activate the remote control in VCR
mode. (See page 12.)
• Press to select the VCR output mode.
5
6
7
9
REC / OTR button (VCR)
• Press once to start recording.
• Press repeatedly to start a one-touch timer
recording.
• Press to activate the remote control in VCR
mode. (See page 12.)
25
26
27*
28
8
DVD
REC/OTR
REC/OTR
VCR
9
10
REC SPEED
PLAY
PAUSE
STOP
11
12
13
29
REC MONITOR SKIP
SKIP
30
SEARCH
SLOW
CM SKIP
10 r button (DVD / VCR)
DVD mode
31
32*
14
AUDIO
DUBBING ZOOM
• During playback, press to reverse fast.
• When playback is paused, press to reverse
slowly.
15
16
33
VCR mode
• Press to rewind the video tape.
• Press to view the picture rapidly in reverse
during the playback mode.
11 REC SPEED button (DVD / VCR)
• Press to switch the recording speed.
12 REC MONITOR button (DVD)
• Press to check the video and audio quality
before attempting to record and during
recording.
*You can also turn on the unit by pressing these
buttons when the remote control is in DVD mode.
1
2
STANDBY-ON button (DVD / VCR)
• Press to turn on or off the unit.
13 SLOW button (VCR)
• During playback, press to view the video tape in
slow motion.
T-SET button (DVD / VCR)
• Press to enter the timer-standby mode. In the
timer-standby mode, press to cancel the mode
and to turn on the unit.
14 CM SKIP button (DVD)
• During playback, press to skip 30 seconds.(See
page 41.)
3
Number buttons (DVD / VCR)
• Press to select channel numbers.
• Press to select a title / chapter / track on the
display.
15 DUBBING button (DVD / VCR)
• Press to start VCR to DVD (DVD to VCR)
duplication which you set in the setting menu.
• Press to enter values for settings in the setting
menu.
• Press to enter the number in the Index or Time
search in VCR mode.
16 ZOOM button (DVD)
• During playback, press to enlarge the picture on
the screen.
• Press to enter the characters in edit function.
17 OPEN / CLOSE / EJECT O button* (DVD /
4
DISPLAY button (DVD / VCR)
• Press to display the on-screen display.
VCR)
• Press to open or close the disc tray.
• Press to remove the tape from the unit.
EN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 11 Thursday, March 31, 2005 10:04 PM
VCR mode
18 TIMER PROG. button (DVD / VCR)
• Press to display the timer programme setting
menu.
• Press to rapidly advance the video tape.
• Press to view the picture rapidly in forward
during playback.
19 PROG. U / D buttons (DVD / VCR)
DVD mode
29 PAUSE p button (DVD / VCR)
• Press to pause playback or recording.
• Press up and down to change the channel.
30 SKIP B button (DVD)
• During playback, press to skip to the previous
chapter or track.
VCR mode
• Press to change the channel up and down.
• Press to adjust the tracking during playback or
in slow motion of the tape.
• While playback is in still mode, you can adjust
the vertically blurred picture.
• When playback is paused, press to play reverse
step by step.
SKIP F button (DVD)
• During playback, press to skip to the next
chapter or track.
20 REPEAT button (DVD)
• Press to select the repeat mode.
• When playback is paused, press to advance
step by step.
21 SETUP button (DVD / VCR)
• Press to display the setting menu in stop mode.
31 SEARCH button (VCR)
• Press to call up the index or time search menu.
22 CLEAR button (DVD / VCR)
DVD mode
32 STOP S button* (DVD / VCR)
• Press to clear the password once entered.
• Press to cancel the programming for a disc.
• Press to clear the selecting marker number in
the marker setup mode.
• Press to clear the program once entered in the
timer recording setting mode.
• Press to stop playing back or recording.
33 AUDIO button (DVD / VCR)
DVD mode
• If you receive bilingual broadcast, or set
“External input Audio” to “Bilingual,” press to
change the AUDIO OUT setting “Main,” “Sub”
and “Main/Sub.”
VCR mode
• Press to reset the tape counter.
• Press to display the audio menu during
playback.
23 ENTER button (DVD / VCR)
• Press to confirm or select menu items.
• Press to select the sound mode.
VCR mode
24 RETURN R button (DVD / VCR)
• Press to return to the previously displayed menu
screen.
• During playback a Hi-Fi video tape, press to
change the AUDIO OUT setting “STEREO,”
“LEFT,” “RIGHT,” and “MONO.” (If you receive
bilingual broadcast, or set “External input Audio”
to “Bilingual,” press to change the AUDIO OUT
setting “Main,” “Sub,” and “Main/Sub.”)
25 DVD
button
• Press to activate the remote control in DVD
mode. (See page 12.)
• Press to select the DVD output mode.
26 REC / OTR button (DVD)
• Press once to start a recording.
• Press repeatedly to start a one-touch timer
recording.
• Press to activate the remote control in DVD
mode. (See page 12.)
27 PLAY P button* (DVD / VCR)
• Press to start or resume playback.
28 f button (DVD / VCR)
DVD mode
• During playback, press to forward fast.
• When playback is paused, press to forward
slowly.
Button names described in the Owner’s Manual
The instructions in this manual are described mainly with the operations using the remote control. Some
operations can be carried out using the buttons on the front panel.
11
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 12 Thursday, March 31, 2005 10:04 PM
Installing batteries in the remote
control
Install two R6 (AA) batteries (supplied) into the
remote control, carefully match with the polarity
indicated inside the battery compartment.
VCR / DVD recorder Switching
Because this product is a combination of a VCR and a
DVD recorder, you must select first which component
you wish to operate with [SELECT LP] on the front
panel.
OPEN/CLOSE
REW
FFWD STOP/EJECT PLAY RECORD
PROG.
DUBBING
SELECT
SELECT
STOP
PLAY RECORD
STANDBY-ON
1
2
3
VCR
DVD
S-VIDEO
VIDEO L(MONO)-AUDIO-R
SELECT
SELECT
VCR
DVD
DVD SELECT
indicator
Caution
• Incorrect use of batteries can result in hazards such
as leakage and bursting.
VCR SELECT
indicator
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
• Make sure that the plus and minus ends of each
battery match the indications inside the battery
compartment.
VCR mode
Press [VCR
(Verify that the VCR SELECT indicator is lit.)
] on the remote control.
• Remove batteries if the equipment will not be used
for a month or more.
DVD mode
• When disposing used batteries, please comply with
governmental regulations or the public instructions
for environmental protection that apply in your
country or area.
Press [DVD
(Verify that the DVD SELECT indicator is lit.)
] on the remote control.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
Note
• Pressing only [SELECT LP] on the front panel
DOES NOT switch the mode of the remote control.
You MUST select the correct mode on the remote
control.
• Press [SELECT LP] to select the DVD mode or the
VCR mode.
About the remote control
• Make sure there is no obstacle between the remote
control and the remote control sensor on the unit.
• Use within the operating range and angle as shown.
• You cannot switch to the mode (DVD or VCR) that is
in the timer-standby mode.
• If the media is available, you can start recording by
pressing [REC / OTR] (DVD) or [REC / OTR] (VCR)
on the remote control even if another equipment
(DVD or VCR) is selected. In this case, the mode of
the remote control will be automatically switched to
the appropriate component.
Within about
7 m
60˚
P
OW
ER
DI
SP
LA
Y
C
H
.
TI
PR
M
OGER
.
Remote
control
@
/:
J
M
D
R
1
O
EC
O
O
P
N
IT
G
E
N/
R
R
H
I
A
C
LO
E
B
C
4
C
S
E
S
P
2
P
Q
E
R
E
S
K
R
C
7
L
DE
F
E
LE
5
C
A
TU
3
R
V
M
NO
P
A
8
U
S
P
6
SE
A
C
WX
E
YZ
RE
0
V
CM
9
S
SK
KIP
PL
IP
A
Y
T
OR
O
P
M
ST
OP
I
G
E
IN
N
U/
AL
FW
D
EN
P
M
TE
LA EN
U
IS
R
Y
L
T
• Remote control operation may become unreliable if
the remote control sensor of the unit is being
exposed by the strong sunlight or fluorescent light.
• Remote controls for different devices can interfere
with each other. Be careful when using remote
controls for other equipment located close to the
unit.
• Replace the batteries when the operating range of
the remote control reduces.
EN
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 13 Thursday, March 31, 2005 10:04 PM
1
2
3
Current time.
Guide to On Screen Displays
Position number.
Audio status of the receiving broadcast
or external equipment.
DISPLAY menu
DVD mode
4
Audio status of the currently playing
back video tape.
Press [DVD
] first.
With a disc inserted into the unit, press [DISPLAY] to
display the on screen display. The menu shows
5
6
7
Tape counter.
information about what is recorded on the disc.
1
1
1
0:00:00
DVD-RW
3
4
Recording or playing back speed.
Status of the current tape.
Video mode
P22
Main
2
While in the VCR mode, the on screen display of the
VCR mode is displayed.
2H
1:35
6
5
Setting menus
This is an example screen for explanation.
Displayed items vary depending on the actual
mode.
Press [SETUP] in stop mode to display “Easy Setting
Menu” or “Advanced Setting Menu”. Choose either
“Easy Setting Menu” or “Advanced Setting Menu”
using [Cursor U / D], then press [ENTER] to
change between the menus.
1
Disc type and format mode.
In some descriptions in this manual, only one type of
disc is indicated as an example.
“Easy Setting Menu” and “Advanced Setting Menu”
are available from the Setting Menu. The “Easy
Setting Menu” consists of the settings frequently
needed, while the “Advanced Setting Menu” consists
of all the settings available. You can set the items
2
3
4
Position number and audio status of the
programme.
marked with
in the “Easy Setting Menu.”
Title number, chapter number and the
time lapse of disc playback.
The unit remembers which setting menu you used last
time and recalls it when you press [SETUP] in stop
mode next time, even if power is switched off. (i.e., if
you use the “Easy Setting Menu” and then turn the
unit off, the “Easy Setting Menu” will appear next time
you turn on the unit and press [SETUP] in stop
mode.)
Each icon means:
: Search
: Audio
: Subtitle
: Angle (except VR mode)
: Repeat
Easy Setting Menu:
You can make the settings of the basic items as follows.
: Marker
VCR DVD
Easy Setting Menu
: Noise Reduction
: Zoom
Clock
1
2
3
4
5
6
Channel
DVD-RW Recording Format
Timer Programming
Auto Finalise
Disc
Video mode
5
6
Recording mode and remaining time.
Status of the current disc.
VCR mode
Advanced Setting Menu
Press [VCR
] first.
Press [DISPLAY] to display the on screen display.
1
Clock:
12:00
1
AV2
Set the unit clock.
2
STEREO
3
2
Channel:
Set up auto tuning or manual tuning.
3
DVD-RW Recording Format:
7
6
Select the DVD-RW recording format between Video
mode and VR mode.
SP
0:00:00
5
STEREO
4
This is an example screen for explanation.
Displayed items are depending on the actual
mode.
13
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 14 Thursday, March 31, 2005 10:04 PM
DVD-R & DVD-RW (Video mode)
4
Timer Programming:
Programme a timer recording.
Disc
Title List
1
5
Auto Finalise:
Format
2
Set Auto Finalise to “ON” or “OFF.”
Finalise
3
6
Disc / CD Playback Mode:
DVD-RW (VR-mode)
“Disc” is available only when a DVD-RW / R disc is
inserted into the unit. If a DVD-Video (commercially
available), a new DVD-R disc or a finalised DVD-R
disc is inserted into the unit, you cannot select “Disc.”
“CD Playback Mode” is available only when an Audio
CD, Video CD or a CD-RW / R disc with MP3 / JPEG /
KODAK PICTURE CD files recorded is inserted into
the unit.
Disc
Playlist
1
Original
1
Format
2
3
4
Finalise
Disc Protect OFF ON
CD, MP3, JPEG, KODAK PICTURE CD & Video
CD
Advanced Setting Menu:
You can make all the settings available as follows.
CD Playback Mode
Random Play
5
Program Play
6
Advanced Setting Menu
PBC(Video CD only)
Slide Show
OFF
7
8
Playback
1
5 sec.
Recording
2
Display
3
Select Video
4
Clock
This is an example screen for explanation. Some
items will be displayed in grey depending on the
inserted disc.
5
Channel
6
Disc
7
Easy Setting Menu
1
Title List / Playlist / Original:
1
Playback:
Display the titles recorded on the disc.
Set up the unit to play back a disc.
2
Format (DVD-RW only):
Erase all of the recorded content on the disc.
• It is not possible to recover erased content. Make
sure before you format a disc.
2
Recording:
Set up the unit to record to a disc or a tape.
• It is not possible to use a disc formatted with this unit
in another DVD recorder. When you use a disc with
another DVD recorder, format a disc using that DVD
recorder.
3
Display:
Set up the front panel display of the unit.
4
Select Video:
Choose an external input to record from other video
equipment to a disc or a tape.
3
Finalise:
Finalise a disc containing recorded titles.
5
Clock:
4
Disc Protect (VR mode only):
Set the unit clock.
Protect a disc from accidental over-recording, editing
or erasing.
6
Channel:
Set up and adjust channels.
5
Random Play:
Activate the random playback feature.
7
Disc / CD Playback Mode:
“Disc” is available only when a DVD-RW / R disc is
inserted into the unit. If a DVD-Video (commercially
available), a new DVD-R disc or the finalised DVD-R
disc is inserted into the unit, you cannot select “Disc.”
“CD Playback Mode” is available only when an Audio
CD, Video CD or a CD-RW / R disc with MP3 / JPEG /
KODAK PICTURE CD files recorded is inserted into
the unit.
6
Program Play (except MP3 / JPEG /
KODAK PICTURE CD files):
Activate the programmed playback feature.
7
PBC (Video CD only):
Turn the PBC function “ON” or “OFF.”
8
Slide Show (JPEG / KODAK PICTURE CD
files only):
Select the display time.
EN
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 15 Thursday, March 31, 2005 10:04 PM
Front Panel Display Guide
4
2
1
3
5
DVD R:
1
Current status of the unit
Appears when a DVD-R disc is inserted
into the unit.
p:
Appears when a disc or a tape playback
is paused.
Appears also during step by step
playback.
DVD RW:
Appears when a DVD-RW disc is inserted
into the unit.
P:
Appears when playing back a disc or a
tape.
VCR: Appears when the timer recording is
proceeding in VCR.
pP: Appears during slow forward or slow
Appears when VCR is in the timer-
standby mode.
revese playback.
:
Appears when the timer programming or
one-touch timer recording (OTR) is set
and is operating.
Flashes when switch to the timer-standby
mode while programming cannot set.
VCR→DVD:
Flashes when all the timer programmes
are finished.
Flashes when there is an error in
programming.
Appears during VCR to DVD duplication
process.
VCR←DVD:
Appears during DVD to VCR duplication
process.
REC: Appears when recording.
Flashes when recording being paused.
REPEAT:
3
Recording speed
• Selected recording speed appears during
recording or in stop mode.
Appears during repeat playback (only for
disc playback).
: Appears when a tape is in the unit.
• Recording speed appears during VCR playback.
2
Disc type and Current status of the unit
4
5
Title / Track and Chapter mark
CD:
Appears when an Audio CD or a disc with
MP3 / JPEG / KODAK PICTURE CD files
recorded is inserted into the unit.
:
:
Title / track number.
Chapter number.
Displays the following
• Playing back time / remaining time
• Current title / chapter / track number
• Recording time
• Clock
• Channel number
• VCR tape counter
• One-touch timer recording (OTR) remaining
time
VCD: Appears when a Video CD is inserted into
the unit.
DVD: Appears when a DVD is inserted into the
unit, or when recording or the timer-
standby mode.
Flashes when switch to the timer-standby
mode while programming cannot set.
Display messages
The disc tray is
open.
A disc is inserted
into the unit.
The PBC function
of the Video CD is
activated.
Data is being
recorded on a disc.
The disc tray is
closing.
15
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 16 Thursday, March 31, 2005 10:04 PM
Getting Started
To Aerial jack
Antenna
Cable
Signal
Audio/Video cable (not supplied)
3
Scart/RCA
cable (not
supplied)
or
3
Scart cable (supplied)
Scart adaptor
(not supplied)
2
RF cable
(supplied)
DVD/VCR
V2(DECODER)
DVD
AUDIO
OUT
DVD/VCR
AERIAL
DIGITAL
S-VIDEO
OUT
AUDIO OU
OPTICAL COAXIAL
L
1
AV1(TV)
RF OUT
R
RF cable
(not supplied)
*The unit is for the DRV-B2737.
3 Connect the AUDIO OUT jacks of this
unit to the Analogue audio input
jacks of your TV. Use a commercially
available Audio cable.
Connections
AUDIO IN S-VIDEO IN
Connecting to a TV
Connect the unit to a TV after considering the
capabilities of your existing equipment.
Before installation, plug off your TV and this unit.
Using the Scart jack
DVD/VCR
AV2(DECODER)
DVD
AUDIO
OUT
DVD/VCR
AERIAL
IGITAL
S-VIDEO
OUT
AUDO OUT
1 Connect the antenna or cable to the
OPTICAL COXIAL
L
AV1(TV)
AERIAL jack of this unit.
RF OUT
R
2 Connect the RF OUT jack of this unit
to the Aerial jack of your TV. Use the
supplied RF cable.
*The unit is for the DRV-B2737.
Note for a TV with no S-Video input jacks or
Scart jack:
• This unit has no RF modulator, so this type of TV
3 Connect AV1 (TV) Scart jack of this
unit to the Scart jack of your TV. Use
the supplied Scart cable.
cannot be used.
Note
• If your TV does not have a Scart jack, use commercially
available Scart adaptor or Scart/RCA cable to connect.
Use only AV1 (TV) or AV2 (DECODER) jack for the
VCR output signals of this unit.
Connecting to external equipment
This unit has three input terminals, AV1 or AV2 on the
rear panel and AV3 on the front panel. Be sure that all
the units are off before making connections.
Using the S-VIDEO OUT jack and the AUDIO
OUT jack (only for DVD)
If your TV has an S-Video input jack, use S-Video and
Audio cables to connect.
Recording from a DVD player, VCR or other Audio-
Video equipment with a Scart output jack (AV2)
1 Follow steps 1 and 2 above.
2
Connect S-VIDEO OUT jack of this unit
to the S-Video input jack of your TV. Use
commercially available S-Video cable.
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 17 Thursday, March 31, 2005 10:04 PM
The connections illustrated above are
optional for better sound.
AV output jack
(Scart)
1 For clear digital sound quality, use
the DIGITAL AUDIO OUT (OPTICAL
(DRV-B2737 only) or COAXIAL) jack
to connect your digital audio
equipment.
Scart cable (supplied)
AV2 (Rear)
If the audio format of the digital output does not
match the capabilities of your receiver, the
receiver will produce a strong, distorted sound or
no sound at all.
DVD/VCR
DVD
AUDIO
OUT
DVD/VCR
AERIAL
DIGITAL
S-VIDEO
OUT
AV2(DECODER)
AUDIO OUT
OPTICAL COAXIAL
L
AV1(TV)
RF OUT
R
*The unit is for the DRV-B2737.
Recording from a camcorder or other
Connecting a Dolby Digital™ decoder, DTS
decoder or MPEG decoder
Audio-Video equipment with no Scart output
• Connecting multi-channel Dolby Digital decoder
allows you to enjoy the 5.1ch Dolby Digital surround
system as well as DTS decoder, 5.1 channel
surround system.
• After connecting to a Dolby Digital decoder, set
“DOLBY DIGITAL” to “Stream” in the AUDIO menu.
(See page 60.)
• After connecting to a DTS decoder, set “DTS” to
“ON” in the AUDIO menu. (See page 60.)
• After connecting to a MPEG decoder, set “MPEG” to
“Stream” in the AUDIO menu. (See page 60.)
jack (AV3)
If no S-Video input jack is available, connect to
VIDEO input jack on the front panel using an RCA
Video cable.
Change the setup when using S-VIDEO IN jack. (See
page 32.)
AV3 (Front)
OPEN/CLOSE
DUBBING
SELECT
SELECT
STOP
PLAY RECORD
Connecting to an MD deck or DAT deck
VCR
DVD
-VIDEO
VIDEO MONO)-AUDIO-R
• The audio source recorded in Dolby Digital 5.1
channel surround format cannot be recorded using
an MD or DAT deck as a digital sound.
• If not connected to a Dolby Digital decoder, set
“DOLBY DIGITAL” to “PCM” in the AUDIO menu.
Playing back a DVD using incorrect settings may
generate noise distortion, and damage speakers.
• Set “DOLBY DIGITAL,” and “MPEG” to “PCM” and
set “DTS” to “OFF” in the AUDIO menu for
connecting to an MD or DAT deck.
S-Video cable
(not supplied)
Audio cable
(not supplied)
• You can use AUDIO OUT jacks for the connection of
your audio system.
*The unit is for
S-VIDEO AUDIO
OUT OUT
the DRV-B2737.
After you have completed
connections
Switch the input selector on your TV to an appropriate
external input channel. For details, refer to the
Owner’s Manual of your TV.
Digital audio for better sound quality
(only for DVD)
Dolby Digital decoder,
DTS decoder or
MPEG decoder, etc.
Digital audio
input jacks
OPTICAL
COAXIAL
Note
• Connect this unit directly to the TV. If the AV cables
are connected to a VCR, pictures may be distorted
due to the effects of the copy protection system.
or
DVD
AUDIO
OUT
Coaxial cable
(not supplied)
DIGITAL
S-VIDEO
OUT
AUDIO OUT
OPTICAL COAXIAL
L
R
Optical cable
(not supplied)
DVD/VCR
AV2(DECODER)
DVD
AUDIO
OUT
DVD/VCR
AERIAL
DIGITAL
S-VIDEO
OUT
AUDIO OUT
OPTICAL COAXIAL
L
*The unit is for
AV1(TV)
RF OUT
R
the DRV-B2737.
17
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 18 Thursday, March 31, 2005 10:04 PM
Manual tuning
Channel setting
Manually tune each channel.
Tuning of this unit to broadcast channels can be
performed in two ways.
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
Auto tuning
Programme the tuner to scan only the channels you
can receive in your area.
2 Select “Channel” using
[Cursor U / D], then press [ENTER].
3 Select “Manual Tuning” using
[Cursor U / D], then press [ENTER].
1 Press [STANDBY-ON] to turn on the
unit.
VCR DVD
Manual Tuning
2 Turn the TV on and select the input
to which the unit is connected.
Position
Channel
P01
12
3 In stop mode, press [SETUP].
Decoder
Skip
OFF
OFF
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
4 Select “Channel” using
[Cursor U/ D], then press [ENTER].
4 Select “Position” using
5 Select “Auto Tuning” using
[Cursor U/ D], then press [ENTER].
[Cursor U/ D], then press [ENTER].
The unit will start storing channels available in
your area.
5 Select the position number you wish
to use using [the Number buttons] or
[Cursor U/ D], then press
[RETURN R].
You can select position numbers 01 to 99.
P 01
6 Select “Channel” using
Auto Tuning Now
[Cursor U/ D], then press [ENTER].
7 Press [Cursor U/ D] to start
scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
Wait for several minutes to finish channel storing.
• You can select a desired channel number using
[the Number buttons]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
6 Press [SETUP] to exit.
You can select only the channels memorized in
this unit by using [PROG. U/ D].
(To select channel 4, press [0] first and then
press [0] and [4], or press [4]. Or press [4] and
then “– – 4” appears and wait for 2 seconds.)
• If this is the channel you want, press
[RETURN R].
To select a channel
You can select a channel using [PROG. U/ D], or
directly enter the channel using
[the Number buttons] on the remote control.
To cancel auto tuning
Channel Plan
Press [RETURN R] or [SETUP] during scanning.
Ch. Indication
01 - 10
TV Channel
IRA - IRJ, GAP
E21 - E69
Note
21 - 69
• The selection will be affected by how you receive TV
channels in your local area.
74 - 78
X, Y, Z, Z+1, Z+2
S1 - S20, GAP
S21 - S41
• If the auto tuning is cancelled during scanning,
some channels not yet tuned may not be received.
• You cannot change the channel when either VCR or
DVD is in any recording mode (normal recording,
one-touch timer recording or timer recording).
80 - 99, 100
121 - 141
This unit can receive the Hyper and Oscar
frequency bands.
EN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 19 Thursday, March 31, 2005 10:04 PM
• If “Skip” is set to “ON,” select “Skip” using
[Cursor U/ D], then press [ENTER]. Select
“OFF” using [Cursor U/ D], then press
[RETURNR].
• If you want to decode scrambled signals, select
“Decoder” using [Cursor U/ D], then press
[ENTER]. Select “ON” using [Cursor U/ D],
then press [RETURN R].
3 Select “Channel” using
[Cursor U/ D], then press [ENTER].
4 Select “Move” using [Cursor U/ D],
then press [ENTER].
5 Select the position number of which
you want to change the channel
using [Cursor U/ D], then press
[ENTER].
• To store another channel, repeat steps 4 to 7.
8 After completion, press [SETUP] to
exit.
You cannot select a position number where
“– – –” appears next to the number, because
“Skip” is set to “ON” for that position number.
To select a channel
6 Move the channel to another position
number using [Cursor U/ D], then
press [ENTER].
Notes on using the Number buttons:
• Enter channel numbers as a two-digit number for the
quickest result. For example, to select channel 6,
press [0] and [6]. If you only press [6], channel 6 will
be selected after 2 seconds. You can only select
channels 1 to 99.
• To move another channel, repeat steps 5 to 6.
7 Press [SETUP] to exit.
• You can select the external input mode “AV1,” “AV2”
or “AV3.”
• To select “AV1,” press [0], [0], [1].
• To select “AV2,” press [0], [0], [2].
• To select “AV3,” press [0], [0], [3].
To skip a Preset channel
You can set the unit to skip channels you can no
longer receive or seldom watch when you access
channels using [PROG. U/ D].
1 Follow steps 1 to 3 in “Manual
tuning.”
2 Select “Position” using
[Cursor U/ D], then press [ENTER].
3 Select the position number you wish
to skip using [the Number buttons]
or [Cursor U/ D], then press
[RETURN R].
4 Select “Skip” using [Cursor U/ D],
then press [ENTER].
5 Select “ON” using [Cursor U/ D],
then press [RETURN R].
• To skip another channel, repeat steps 2 to 5.
6 Press [SETUP] to exit.
Move
You can replace two channels.
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
If it has already appeared, proceed to step 3.
19
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 20 Thursday, March 31, 2005 10:04 PM
Manual Clock Setting
Setting the clock
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
Auto Clock Setting
Channel Tuning must be set before setting Auto
Clock.
2 Select “Clock” using [Cursor U/ D],
1 In stop mode, press [SETUP].
then press [ENTER].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
3 If you select “Advanced Setting
Menu,” proceed to step 4.
If you select “Easy Setting Menu,”
proceed to step 5.
If it has already appeared, proceed to step 3.
3 Select “Clock” using [Cursor U/ D],
4 Select “Clock Setting” using
then press [ENTER].
[Cursor U/ D], then press [ENTER].
Advanced Setting Menu
5 Press [ENTER] again.
Playback
Recording
Display
The default date will appear.
VCR DVD
Clock Setting
Select Video
Clock
Channel
Disc
Easy Setting Menu
01 / 01/ 2005(SAT)
0: 00
4 Select “Auto Clock Setting” using
[Cursor U/ D], then press [ENTER].
5 Select “ON” using [Cursor U/ D],
6 Enter the date (day / month / year)
using [Cursor U/ D], then press
[Cursor P].
then press [ENTER].
The current time will be set automatically.
6 Press [SETUP] to exit.
Press [Cursor P] to move the cursor to the next
field. If you wish to go back to the previous field,
press [Cursor L].
7 Press [STANDBY-ON] to turn off.
The Auto clock function is activated.
This unit will search for the time only when the
power is off. Leave the unit off for several minutes
to give it time to set the clock.
7 Enter the time (hours / minutes)
using [Cursor U/ D], then press
[ENTER].
The clock will start.
Hint
• Although seconds are not displayed, they will be
counted from zero.
• If you want to cancel “Auto Clock Setting,” select
“OFF” using [Cursor U/ D], and then press
[ENTER] at step 5.
8 Press [SETUP] to exit.
Note
• Your clock setting will be lost if either there is a
power failure or the unit is unplugged for more than
30 seconds when the “Auto Clock Setting” is “OFF.”
Note
• The default setting of “Auto Clock Setting” is “OFF.”
• The clock may set itself automatically after you
connect the antenna cable to the unit and plug in the
mains cable. In this case, the current time will
appear on the front panel display.
• To set the clock automatically, the channel assigned
to position 01 must receive the PDC signal.
• The clock cannot be set automatically if you are not
receiving a channel in your area that carries a time
signal. In this case, set the clock manually.
• Once the auto clock setting is performed, the unit
will correct the current time by receiving PDC
broadcasts whenever you turn off the unit.
• The unit will correct the current time automatically at
8:00, if the unit power is turned off.
• Between 23:00 and 1:00, the AUTO CLOCK
function will not operate even if the unit power is
turned off.
EN
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 21 Thursday, March 31, 2005 10:04 PM
Selecting the TV aspect ratio
You can select the TV aspect ratio to match the format
of the programme you are playing back with the unit
and that of your TV screen (4:3 standard or 16:9 wide
screen TV).
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3 Select “Playback” using
[Cursor U/ D], then press [ENTER].
4 Select “TV Aspect” using
[Cursor U/ D], then press [ENTER].
DVD
Playback
TV Aspect
4:3 Letter Box
All
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
Dynamic Range Control
Fast Forward with Audio
Video Out
ON
OFF
5 Select the desired option using
[Cursor U/ D], then press [ENTER].
TV Aspect
DVD
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
6 Press [SETUP] to exit.
Hint
If you have a standard TV:
• Select “4:3 Letter Box” for a full width picture
with black bars at the top and bottom.
• Select “4:3 Pan & Scan” for a full height picture
with both sides trimmed.
If you have a wide screen TV:
• Select “16:9 Wide.”
21
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 22 Thursday, March 31, 2005 10:04 PM
Recording
Disc type
Disc format
Functions
Information on DVD recording
Video mode
Video
Playing back,
Limited recording,
Limited editing
DVD-RW
VR mode
VR
Playing back,
Recording, Original /
Type of discs
This unit can record on DVD-R and DVD-RW. You can
record on DVD-R only once. On DVD-RW, you can
record and erase many times.
It is possible to record on DVD-R only in Video mode.
DVD-RW can record in the format you select from
Video mode or VR mode.
DVD-RW
Playlist editing
Video mode
Playing back,
Limited recording,
Limited editing
DVD-R
Recording speed
You can select a recording speed from 6 options.
The recording time will vary depending on the
recording speed you select as follows.
Logo
Attributes
8 cm / 12 cm, single-sided, single layer disc
Max. recording time (10H mode, approx.):
600 minutes (4.7 GB) (for 12 cm)
Recording speed
Recording time
180 minutes (1.4 GB) (for 8 cm)
Video /
Sound
Quality
Front
TV
Panel
12 cm
8 cm
screen
Display
If you want to record repeatedly on the same disc, or if
you want to edit the disc after recording, use a
rewritable DVD-RW type disc.
If you want to save recordings without any alteration,
use a non-rewritable DVD-R type disc.
1H
2H
XP
SP
60 min
18 min
36 min
72 min
108 min
144 min
180 min
Excellent
Very good
Good
120 min
240 min
360 min
480 min
600 min
4H
LP
• Discs that should or should not be used with this
recorder:
DVD-R 8x can be used.
DVD-RW 4x can be used, but 6x or 8x will result in a
recording error.
6H
EP
Average
Low
8H
SLP
SEP
10H
Low
• Discs that were tested and proven as compatible
with this recorder:
Maxell DVD-R, TDK DVD-RW 2x, MITSUBISHI
DVD-R 8x, JVC DVD-RW 4x
• This table is intended for a standard new single-
sided 12 cm disc. The recording times are estimates
and actual recording time may differ.
• The audio and video quality becomes poorer as the
recording time gets longer.
• Discs recorded in 8H or 10H on this recorder may
not be played back on other DVD recorders or DVD
players.
Video mode and VR (Video Recording) mode
Video mode is the same recording format as used on
the pre-recorded DVD-Videos you purchase in local
shops, so you can play back the discs recorded in this
format in most DVD players. You will need to finalise
such discs (see page 34) before playing them back in
other DVD players. Unless finalised, you can play
back, record additional materials or edit discs
recorded in Video mode with this unit.
VR (Video Recording) mode is a basic recording
format for DVD-RW discs. You can record and edit
material repeatedly. It is impossible to record
additional materials on a disc formatted in VR mode
and already recorded in another video system other
than PAL, such as NTSC.
Restrictions on recording
You cannot record copy-protected video using this
unit. Copy-protected video includes DVD-Videos and
some satellite broadcasts.
If copy-protected material is detected, recording will
pause or stop automatically and an error message
appears on the screen.
You can only record “Copy-once only” video using a
DVD-RW disc in VR mode with Content Protection for
Recordable Media (CPRM).
When recording a TV broadcast or an external input,
you can display copy control information on the
screen.
Note
• The following disc cannot be used for recording in
this unit:
DVD-RW 6x
CPRM is a scrambling copy protection system for the
protection of “copy-once” broadcast programmes.
This unit is CPRM compatible, which means that you
can record copy-once broadcast programmes, but you
cannot then make a copy of those recordings. CPRM
recordings can only be played back on DVD players
that are specifically compatible with CPRM.
DVD players bearing the
logo are capable of
playing back DVD-RW discs recorded in VR mode.
EN
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 23 Thursday, March 31, 2005 10:04 PM
Usable discs
✬✬✬: Most suitable, ✬✬: Can be used,
Information on copy control
Some satellite broadcasts include copy-protected
information. If you wish to record them, refer to the
following.
✬: Some functions are limited, —: Cannot be used.
DVD-RW
Applications
DVD-R
VR
✬✬✬
VIDEO
✬✬✬
Copy- Copy- Copy-
Disc type / format
free
once prohibited
Record TV programmes
✬✬
—
ver.1.1 / ver. 1.2
Video
DVD-RW
Reuse by deleting the current
contents
✬✬✬
✬✬✬
✬✬✬
✬✬*
✬✬
✬
ver.1.1 / ver. 1.2 CPRM compatible
Edit the contents
✬
ver.1.1 / ver. 1.2
VR
DVD-RW
Edit / Record from external
equipment
ver.1.1 / ver. 1.2 CPRM compatible
✬✬✬
✬✬✬
✬✬✬
✬✬✬
✬✬✬
✬✬✬
ver.2.0
Copy discs for distribution
DVD-R
Playback on other DVD
equipment
✬✬*
Recordable
Not Recordable
Features
Rewritable
Yes
Yes
Yes
Yes
No
Note
Can create chapters at fixed
intervals (auto)
Yes
• This unit cannot record on CD-RW or CD-R discs.
• DVD-RW / R and CD-RW / R discs recorded on a
personal computer or a DVD or CD recorder may
not be played back if the disc is damaged or dirty or
if there is condensation on the player’s lens.
• If you record a disc using a personal computer, even
if it is recorded in a compatible format, it may not be
played back because of the settings of the
application software used to create the disc. (Check
with the software publisher for more detailed
information.)
Can create chapters wherever
you like (manual)
Yes
Yes
Yes
No
Yes
No
No
Yes
No
Can record 16:9 size pictures
Can record Copy-Once
programmes
Can perform basic editing
functions
Yes
Yes
Yes
No
Yes
No
Can perform advanced editing
functions (Playlist edit)
*You can only play back DVD-RW disc recorded in VR
mode on VR-compatible discs.
• Discs recorded in Video mode on this unit cannot
record additional information using other DVD
recorders.
Note
• It is not possible to use a DVD-RW disc formatted
with this unit in another DVD recorder unless the
content of the disc was also recorded with this unit.
• Since recording is performed using the Variable Bit
Rate (VBR) method, the actual remaining time for
recording may be a little shorter than the remaining
time displayed on the OSD, depending on the
picture you are recording.
• For details of the above functions and restrictions,
see the further explanations in this Manual.
Making discs playable in other DVD
players (Finalise)
After recording, you must finalise the disc to play it
back in other players. (See page 34.)
You cannot finalise discs in other DVD recorders.
After finalising:
• After a DVD-RW / R disc (Video mode) is finalised, a
title menu is created automatically and additional
recording or editing is not possible.
• Even if after a DVD-RW disc (VR mode) is finalised,
additional recording or editing is possible.
• To play back in other DVD players, finalise discs
recorded on this unit.
23
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 24 Thursday, March 31, 2005 10:04 PM
Setting Auto Chapter
Formatting a disc
Video
DVD-RW
VR
DVD-RW
DVD-R
The unit inserts a chapter mark periodically (every 10
minutes by default) during recording. Using the Auto
Chapter menu, you can set this function off or change
the time period.
Choosing the recording format of a
blank DVD-RW disc
Video
DVD-RW
VR
DVD-RW
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
When inserting a blank disc, the unit automatically
starts to initialise the disc. You can also manually
format a DVD-RW disc once it has been used. After
formatting, you can record on the disc with the
recording format selected in the Setting menu.
If it has already appeared, proceed to step 3.
1 In stop mode, press [SETUP].
2 If you select “Advanced Setting
Menu,” proceed to step 3.
If you select “Easy Setting Menu,”
proceed to step 4.
3 Select “Recording” using
[Cursor U/ D], then press [ENTER].
4 Select “Auto Chapter” using
[Cursor U/ D], then press [ENTER].
DVD
Recording
3 Select “Recording” using
[Cursor U/ D], then press [ENTER].
DVD-RW Recording Format
Auto Chapter
Video mode
10 minutes
4 Select “DVD-RW Recording Format”
using [Cursor U/ D], then press
[ENTER].
Timer Programming
Auto Finalise
Bilingual Recording Audio
External input Audio
Dubbing Mode
Main
Stereo
VCR DVD
5 Select “Video mode” or “VR mode”
using [Cursor U/ D], then press
[ENTER].
5 If you wish to set “Auto Chapter”
OFF, select “OFF” using
DVD-RW Recording Format
DVD
Video mode
[Cursor U/ D], then press [ENTER].
Vmode
VR mode
DVD
Auto Chapter
OFF
Video mode
5minutes
10 minutes
15 minutes
30 minutes
60 minutes
DVD Player Compatibility mode.
VR mode
Editing possibility mode.
6 Press [SETUP] to exit.
Note
• The recording format setting is effective only for
DVD-RW discs. You cannot change the recording
format for a DVD-R disc. DVD-R discs are always in
Video mode.
• You cannot mix two formats on one DVD-RW disc.
If you insert a disc that has been recorded before,
the recording format cannot be changed even if you
change it in the Setting menu.
• The unit is not compatible with DVD+RW / R discs.
If a blank DVD+R or DVD+RW disc is inserted, the
error message (“Disc Error”) will appear.
• A Playlist is created automatically during recording
on a DVD-RW disc in VR mode.
If you wish to change the time period
for Auto Chapter, select the required
time period using [Cursor U/ D],
then press [ENTER].
6 Press [SETUP] to exit.
Note
• You cannot set or clear chapter markers on DVD-R
discs. (See page 50.)
EN
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 25 Thursday, March 31, 2005 10:04 PM
Reformatting a disc manually
Selecting the Sound mode
This unit can receive bilingual broadcasts.
Video
DVD-RW
VR
DVD-RW
If you are using a DVD-RW disc, you can format the
disc by performing “Format.” By default it will be in
Video mode. You can change this to VR mode using
the Setting menu.
You can switch between modes by pressing [AUDIO]
on the remote control. Each mode is indicated on the
TV screen as follows.
• During reception of bilingual broadcasts
Note
Display on
the TV
screen
• When you reformat the disc, the contents of the disc
are erased.
Mode
Audio output
Main audio from both
speakers
Insert a recordable disc.
Main
Sub
Main
Sub
Sub audio from both
speakers
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
• Main audio from the left
speaker
• Sub audio from the right
speaker
Main / Sub
Main / Sub
2 Select “Disc” using [Cursor U/ D],
then press [ENTER].
3 Select “Format” using
Setting External input audio
[Cursor U/ D], then press [ENTER].
Video
DVD-RW
VR
DVD-RW
DVD-R
4 Select “Yes” using [Cursor U/ D],
When the external input audio is a bilingual
broadcast, or when copying a video tape to a DVD
disc, you can choose “Stereo” or “Bilingual” to record
on a DVD.
then press [ENTER].
Format
Yes
No
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
Are you sure?
Yes
No
If it has already appeared, proceed to step 3.
3 Select “Recording” using
A Popup window will appear and prompt you to
confirm.
[Cursor U/ D], then press [ENTER].
If you want to cancel formatting, select “No.”
4 Select “External input Audio” using
[Cursor U/ D], then press [ENTER].
5 Select “Yes” using [Cursor U/ D],
then press [ENTER].
Recording
DVD
Formatting will start.
If you want to cancel formatting, select “No.”
DVD-RW Recording Format
Auto Chapter
Video mode
10 minutes
6 Formatting is complete.
Timer Programming
Auto Finalise
100% is indicated.
Bilingual Recording Audio
External input Audio
Dubbing Mode
Main
Stereo
Note
VCR DVD
• It is not possible to use a disc formatted with this unit
in another DVD recorder. When you use a disc with
another DVD recorder, format a disc using that DVD
recorder.
25
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 26 Thursday, March 31, 2005 10:04 PM
5 Select “Stereo” or “Bilingual” using
[Cursor U/ D], then press [ENTER].
Basic recording
External input Audio
DVD
Video
DVD-RW
VR
DVD-RW
DVD-R
Stereo
Follow the steps below to record a TV programme.
Bilingual
1 Turn on the unit and insert a
recordable disc.
Make sure that the TV input is set on the unit.
This operation may take a few moments to
complete.
2 Press [DVD ].
6 Press [SETUP] to exit.
Hint
3 Select the recording speed using
[REC SPEED] (See page 22.).
Make sure that the recording format is set to the
desired mode (see page 24).
Stereo:
Both modes of Video and VR are recorded
in stereo.
Bilingual: The sound you set by “Bilingual Recording
Audio” is recorded in Video mode.
4 Select the desired channel to record
using [PROG.U/ D] or
Both sounds of “Main” and “Sub” are
recorded in VR mode. You can select
audio modes during playback.
[the Number buttons].
5 Press [REC / OTR] to start recording.
Setting Bilingual Recording Audio
Video
The ● mark will be displayed for 5 seconds.
To pause the recording, press [PAUSE p]. Press
[REC / OTR] or [PAUSE p] to restart the
recording.
DVD-RW
DVD-R
You can select either “Main” or “Sub” audio to record a
bilingual broadcast in Video mode.
6 Press [STOP S] to stop the
recording.
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
This operation may take a few moments to
complete.
Hint
• You can change the channel while in the REC pause
mode.
If it has already appeared, proceed to step 3.
3 Select “Recording” using
Note
[Cursor U/ D], then press [ENTER].
• Recording starts immediately and continues until the
disc is full or you stop recording.
4 Select “Bilingual Recording Audio”
using [Cursor U/ D], then press
[ENTER].
• If the clock is not set, the date and time space next
to title names in the Original or Playlist will be blank.
• You cannot mix two formats on DVD-RW discs. If
you insert a previously recorded disc, changing the
recording format is not possible even if you change it
in the Setting menu.
5 Select “Main” or “Sub” using
[Cursor U/ D], then press [ENTER].
• You cannot change the recording speed while in the
REC or REC pause mode.
Bilingual Recording Audio
DVD
• It is possible to record video only in the PAL system.
• During recording, if a signal other than PAL is
decoded (such as NTSC), recording is paused.
Main
Sub
6 Press [SETUP] to exit.
EN
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 27 Thursday, March 31, 2005 10:04 PM
Checking the recording picture and
sound quality
One-touch timer recording
(OTR)
Video
DVD-RW
VR
DVD-RW
DVD-R
Video
DVD-RW
VR
DVD-RW
Before recording on a DVD, you can confirm the
quality of the picture and sound with the recording
speed you selected.
DVD-R
This is a simple way to set the recording time in blocks
of 30 minutes. Check that the disc you are recording
onto has enough space remaining for the time you
set.
When the recording finishes the recorder
automatically switches to the timer-standby mode.
1 Make sure that the unit is in STOP or
REC mode and a DVD is inserted
correctly.
2 Press [REC MONITOR].
1 Turn on the unit and insert a
recordable disc.
The TV will display the programme and output the
sound you are about to record in the quality of the
picture and sound (determined by the recording
speed) you selected.
Make sure that the TV input is set on the unit.
2 Press [DVD ].
3 Select the recording speed using
• If you want to change the recording speed (to
improve the recording quality), press
[REC SPEED] repeatedly.
The recording speed is changed each time you
press the button.
[REC SPEED] (See page 22.).
Make sure that the recording format is set to the
desired mode (see page 24).
4 Select the desired channel to record
using [PROG. U/ D] or
1H(XP)
2H(SP)
4H(LP)
6H(EP)
8H(SLP)
10H(SEP)
[the Number buttons].
• You cannot change the recording speed during
recording.
5 Press [REC / OTR] repeatedly until
the desired recording time (30
minutes to 8 hours) appears on the
TV screen.
3 Press [REC MONITOR] again to exit.
Hint
• If you press [REC MONITOR] while receiving the
bilingual broadcast, the sound to be recorded is
output.
One-touch timer recording will start.
0:30
1:00
(Normal Recording)
8:00
7:30
• When the unit reaches the specified time, it will
be turned off automatically.
• To change the recording length during one-
touch timer recording, press [REC / OTR]
repeatedly until the desired length appears.
• To cancel one-touch timer recording within the
specified time, press [STOP S].
Hint
• The remaining recording time will appear on the TV
screen during one-touch timer recording. Press
[DISPLAY] to see it on the TV screen.
• The remaining recording time will be displayed on
the front panel display during one-touch timer
recording.
• Unlike timer recording, you can perform the
following operations during one-touch timer
recording.
- Turn off the power.
- Use [REC / OTR] or [STOP S].
27
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 28 Thursday, March 31, 2005 10:04 PM
Note
• You cannot use the pause function during one-touch
timer recording.
• The unit will be turned off automatically under the
following conditions.
Timer recording
Video
DVD-RW
VR
DVD-RW
VCR
DVD-R
You can set the unit to record up to 8 programmes, up
to a month in advance. Daily or weekly programme
recordings are also available.
• Be sure to set the clock before entering a timer
programming.
• You can select the timer programming list by
pressing [TIMER PROG.]. In this case, continue
from step 5.
- No space remains on the disc.
- If a power failure occurs.
• If DVD one-touch timer recording is completed
during VCR playback or recording, the DVD will be
in stop mode and the VCR keeps the current mode.
• When one-touch timer recording is finished and the
power is turned off, the unit will switch to the timer-
standby mode automatically if a timer recording has
been programmed. Press [T-SET] to cancel the
timer-standby mode to use the unit continuously.
Insert a recordable disc or a tape with a
record tab.
1 In stop mode, press [SETUP].
2 If you select “Advanced Setting
Menu,” proceed to step 3.
If you select “Easy Setting Menu,”
proceed to step 4.
3 Select “Recording” using
[Cursor U/ D], then press [ENTER].
4 Select “Timer Programming” using
[Cursor U/ D], then press [ENTER].
The Timer Programming list will appear.
5 Select a programme that is not set
using [Cursor U/ D], then press
[ENTER].
Timer Programming
VCR DVD
Speed
DVD
VCR
Date Start End
CH
PDC
1. - - -
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
6 Enter the date using [Cursor U/ D],
then press [Cursor P].
Each time you press [Cursor D] at the current
date, the timer recording mode will change as
follows.
e.g., 1st January
01/01
D
Daily
D
M-F (Mon.-Fri.)
D
W-SAT
D
W-FRI
D
D
W-SUN
D
31/01
EN
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 29 Thursday, March 31, 2005 10:04 PM
• If a basic recording or one-touch timer recording is
in progress on one component (e.g. VCR) and the
timer recording set for the other component (e.g.
DVD) is about to begin, the unit automatically
switches to the programmed channel for timer
recording 2 minutes before the programmed starting
time, and the recording in progress (for VCR) will be
cancelled UNLESS their recording channels are the
same. If their recording channels are the same, the
timer recording will start without cancelling the
recording currently in progress. In this case, the
recording of the same channel will be made on both
DVD and VCR.
7 Enter the time to start and to end
using [Cursor U/ D], then press
[Cursor P].
8 Select the channel number to record
using [Cursor U/ D], then press
[Cursor P].
To record from external input, select “AV1,” “AV2”
or “AV3.”
9 Select the recording media (“DVD” or
“VCR”) using [Cursor U/ D], then
press [Cursor P].
• Cancel the timer-standby mode by pressing [T-SET]
before operation for either DVD or VCR. When
finished operating, press [T-SET] to resume the
timer-standby mode.
10 Select the recording speed using
[Cursor U/ D], then press
[Cursor P].
If PDC is “ON”:
• In the timer-standby mode, you can neither turn on
the power nor use the component (VCR or DVD)
which is not currently timer-programmed.
Refer to “Recording speed” on page 22 for DVD or
page 63 for VCR.
11 Select PDC “ON” or “OFF” using
[Cursor U/ D] (See page 30).
If PDC is “OFF”:
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which
is not currently timer-programmed.
12 Press [ENTER] when all information
required is entered.
Your programme setting is stored.
• To set another programme, repeat steps 5 to 11.
• To exit, press [SETUP] or [TIMER PROG.].
• If the recording times of two or more
programmes overlap, “Overlap” and overlapped
programme numbers are displayed. (See page
29 and 31.)
Checking, cancelling, or correcting
the timer programming information
In the following example, No. 5 timer programming
overlaps on No. 1 and No. 6 timer programmes. In
such a case, you should correct the programme time
to clear the overlap.
VCR DVD
Timer Programming
Date Start End
VCR DVD
Timer Programming
DVD
VCR
CH
Speed
PDC
ON
DVD
VCR
1. 01/01 12:00 13:00 P01 DVD 1H
Date Start End CH
Speed
PDC
ON
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
1. 01/01 12:00 13:00 AV3 DVD
1H
2. - - -
3. - - -
Overlap
4. - - -
No.1 6
5. 01/01 12:30 14:00 P02 VCR
6. 01/01 13:45 21:00 P12 DVD
7. - - -
SP
OFF
OFF
10H
13 Press [T-SET].
8. - - -
The
icon will appear on the front panel display
and the unit enters to the timer-standby mode.
1 Press [T-SET] so that the
icon
Note
disappears from the front panel
display.
• If you have not set the clock, the clock setting
window will appear after step 4. Continue from step
4 in “Manual Clock Setting” on page 20 before
programming the timer.
• Press [Cursor L/ P] to move the cursor in the timer
programming menu.
2 Press [TIMER PROG.].
Timer programming list will appear.
3 Check the information on the list you
will need.
4 To clear the timer programming,
select the desired programme using
[Cursor U/ D], then press [CLEAR].
To correct the timer programming
1)Select the desired programme using
[Cursor U/ D], then press [ENTER].
2)Correct the timer programming using
[Cursor U/ D/ L/ P].
3)Press [ENTER] again.
29
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 30 Thursday, March 31, 2005 10:04 PM
overlapped timer programmes.
•Recording did not start at the start time.
•There is no tape in the cassette
compartment.
•Tape recording reaches to the tape end
during timer recording.
5 Press [TIMER PROG.] to exit.
6 Press [T-SET] to return to the timer
stand-by mode.
To check the timer programming in process
Press [TIMER PROG.].
E41: Power failure
E42: No disc
Note
The error programme will be deleted once you
check the error in the programme list, or once you
cancel the timer-standby mode and re-enter it.
• If a timer recording is proceeding, that programme is
highlighted in red. In such a case, you cannot select
any other programmes.
Press [CLEAR] to erase the selected
programme.
• When you check the timer programming in progress
by pressing [TIMER PROG.] during operations of
the component (DVD or VCR) which is not currently
used for the timer recording, the programme will not
be highlighted. In this case, you cannot select other
programmings.
PDC (Programme Delivery
Control)
The Programme Delivery Control (PDC) assures that
the TV programmes you have programmed for timer
recording are recorded exactly from beginning to end,
even if the actual broadcasting time differs from the
scheduled time due to a delayed start or extension of
the programme duration. Furthermore, if a
To stop the timer recording in
progress
On the front panel of the unit, press
[STOP
S] to stop the disc recording or
[STOP / EJECT SO] to stop the tape
recording.
programme is interrupted, the recording will also be
interrupted automatically and resumed when the
programme starts again.
Note
• [STOP S] on the remote control is not effective.
If the PDC signal drops out because the broadcast
signal is weak, or if a broadcasting station does not
transmit a regular PDC signal, the timer recording is
performed in normal mode (without PDC) even if it
was programmed for PDC. If the starting time of the
PDC timer recording is between 0:00 and 3:59 on a
given day, the PDC function will operate from 20:00
on the previous day to 4:00 on the given day. If the
starting time of the PDC timer recording is between
4:00 and 23:59 on a given day, the PDC function will
operate from 0:00 on the day to 4:00 on the given day.
This means that if the relevant programme is
If the timer programming did not
complete correctly
The error number appears on the timer programming
list.
VCR DVD
Timer Programming
DVD
VCR
Date Start End CH
Speed
PDC
ON
01/01 12:00 13:00 AV3 DVD
E1
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
broadcasted within this period, it is recorded correctly.
If the timer is not programmed correctly, the incorrect
timer setting stays in effect unless you cancel it. To
cancel an incorrect timer setting, refer to “Checking,
cancelling, or correcting the timer programming
information” on page 29.
The error programme will be displayed in grey with
an asterisk and have an error number.
Hints for timer recording
• If there is a power failure or the unit is unplugged for
more than 30 seconds, the clock setting and all
timer settings will be lost.
• If there is no disc or an unrecordable disc in the tray,
the DVD indicator will flash and timer recording will
not occur. Insert a recordable disc.
• If there is no tape or a tape with a record tab is not in
the cassette compartment, the VCR indicator on the
front panel flashes and timer recording cannot be
performed. Please insert a recordable tape.
• When all timer recordings are complete, the
icon flashes. To play back or eject the recorded disc,
press [T-SET], and then press [PLAY P] or
[OPEN / CLOSE / EJECT O].
The error numbers indicate:
E1–E22, E37–E39: Recording error
E23-E24: Unrecordable disc
E25:•Copy prohibited programme
•Cannot record because of the NTSC / PAL-
60 signal is received.
E26–E28: Copy prohibited programme
E29: Disc protected
E30: Disc full
E31: Already recorded 99 titles (Video mode)
E32: Already recorded 99 titles (VR mode)
E33: Already recorded 999 chapters
E34: No space for Control Information
E35: PCA (Power Calibration Area) full
E36: Already finalised Video format disc
E40:•There are some unrecorded parts due the
EN
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 31 Thursday, March 31, 2005 10:04 PM
• The timer recording cannot be performed in DVD
and VCR at the same time. If you set two
programmings with the same channel and time both
in DVD and VCR, the programming that has priority
will be recorded.
If the recording time entirely overlaps:
• The shorter timer programming (PROG. 1) is not
recorded.
PROG. 1
• You cannot make any DVD operation during DVD
timer recording.
• You cannot make any VCR operation during VCR
timer recording.
PROG. 2
Actual
recording
PROG. 2
• If the Start and End times are same, the length of
the recording will be set for 24 hours. If the disc
becomes full during recording, the unit will turn itself
off. To continue recording, press [T-SET] to cancel
the timer stand-by mode, insert a recordable disc
and press [T-SET] again.
Note for DVD recording
• If the recording time of two programmes overlap, or
the End time of a programme and the Start time of
another is same, the first 30 seconds (at the most)
of the subsequent programme are cut off.
• If two or more programmes overlap, “Overlap” and
the overlapped programme number will appear on
the display.
• If the Start time is earlier and the End time is later
than the current time, the recording will start
immediately after you press [T-SET].
If the End time of the programme currently being
recorded and the Start time of the subsequent
programme are same:
• If PROG. 1 is a DVD recorded programme, the
beginning of PROG. 2 may be cut off.
• If a videotape ends during timer recording, the unit
will automatically stop, eject the videotape, and turn
itself off. To continue recording, insert a recordable
tape.
PROG. 1
PROG. 2
Actual
recording
PROG. 1
PROG. 2
The first 30 seconds
(at the most) are cut off.*
Priority of overlapped settings
The unit records programmes according to priority if
timer programmes overlap.
* If the cut off time exceeds 1 minute, the error
number “E40” will appear in the timer programming
list.
If the starting time is same:
• The timer programming set first (PROG. 1) has
priority.
PROG. 2
recording
PROG. 1
will start
after
PROG. 2
PROG. 1
recordingis
completed.
Actual
recording
PROG. 1
PROG. 2
Additional 30 seconds (at the most) are cut off
If programming has been made at the end of the
programming (PROG. 1) currently being recorded:
• The timer programming set first (PROG. 2) has
priority. PROG. 3 will not be recorded.
PROG. 2
recording
PROG. 1
will start
after
PROG. 1
recordingis
completed.
PROG. 2
PROG. 3
Actual
recording
PROG. 1
PROG. 2
Additional 30 seconds (at the most) are cut off
If the recording time is partially overlapped:
• The timer programming with the earlier start time
(PROG. 2) has priority. PROG. 1 will start after
PROG. 2 recording is complete.
PROG. 1
PROG. 2
Actual
recording
PROG. 2
PROG. 1
Additional 30 seconds (at the most) are cut off
31
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 32 Thursday, March 31, 2005 10:04 PM
2 When you want to record to the disc:
Press [DVD ].
Settings for external equipment
Press [OPEN / CLOSE / EJECT O] to
open the disc tray, then place the
disc to record on.
Press [OPEN / CLOSE / EJECT O]
again to close the disc tray.
Connection to external equipment
Video
DVD-RW
VR
DVD-RW
VCR
DVD-R
Connect the external equipment using either the input
jacks, AV1, AV2, (Rear) or AV3 (Front). However, for
AV3 jacks, you have to select S-VIDEO input or
VIDEO input jacks depending on the connected
devices.
When you want to record to a tape:
Press [VCR
].
Insert the tape with a record tab into
the cassette compartment.
Use commercially available Scart, S-Video or Video
cable and an Audio cable for this connection.
3 Select the input terminal to which the
external equipment is connected.
(AV1, AV2 or AV3)
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
To use the input jacks on the back of the unit,
select the “AV1,” “AV2,” position by pressing [0],
[0], [1] or [0], [0], [2] on the remote control or
using [PROG. U/ D].
To use the input jacks on the front of this unit,
select “AV3” position by pressing [0], [0], [3] on
the remote control or using [PROG. U/ D].
If it has already appeared, proceed to step 3.
3 Select “Select Video” using
[Cursor U/ D], then press [ENTER].
4 Select a recording speed using
[REC SPEED].
4 Press [ENTER].
5 Select the input jack type to be used
using [Cursor U/ D], then press
[ENTER].
Refer to “Recording speed” on page 22 for DVD or
page 63 for VCR.
5 Press [RECORD] on the unit to start
recording.
6 Press the PLAY button on the
VCR DVD
AV3 (Front)
external recording component.
Video In
S-Video In
7 For disc:
Press [STOP S] on the unit to stop
recording.
For tape:
Press [STOP / EJECTSO] on the unit
to stop recording.
• If you want to use VIDEO input jack (Composite),
select “Video In.”
• If you want to use S-VIDEO input jack, select “S-
Video In.”
6 Press [SETUP] to exit.
Recording from external equipment
Video
DVD-RW
VR
DVD-RW
VCR
DVD-R
Before recording from external equipment, see page
16 for connection instructions.
1 Turn the TV and the unit on, and
select the input of the TV to which
the unit is connected.
EN
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 33 Thursday, March 31, 2005 10:04 PM
9 Press [PLAY P] on the unit, and then
press [PAUSE p] at the point you
wish to start recording.
Dubbing Mode
Video
DVD-RW
VR
DVD-RW
VCR
DVD-R
10 Press [DUBBING].
You can copy a DVD disc to a videotape or copy a
videotape to a DVD disc. This function will be
available only if the DVD disc or the tape is not copy
protected. Before starting this function, prepare for the
recording on the DVD-R / RW disc or the videotape.
See pages 22 and 63.
VCR to DVD duplication will start.
11 Press [STOP S] to stop the
recording.
Note For VCR to DVD duplication:
• After starting VCR to DVD duplication, the picture
may be distorted because of the auto tracking
function. This is not a malfunction. Be advised to
play back the tape until the picture is stabilized, then
set the starting point which you wish to start
recording, and start VCR to DVD duplication.
• If the playback sound mode of VCR is set to
“STEREO,” “LEFT” or “RIGHT,” the sound mode
upon dubbing is automatically switched to
“STEREO.” If the playback sound mode is set to
“MONO,” the sound mode upon dubbing is also
“MONO.”
• If you set “External input Audio” to “Stereo,” the
sound is recorded in “Stereo” (both Video mode and
VR mode).
• While in video mode, if you set “External input
Audio” to “Bilingual,” the audio set in “Bilingual
Recording Audio” mode is recorded.
Note for recording to a tape:
• The tape’s record tab is intact.
• The videotape is long enough to record the DVD
disc.
Note for recording to a disc:
• The DVD disc is satisfied with the recording status.
See pages 22 and 23.
Insert a disc and a tape with a record
tab.
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
While in VR mode, if you set “External input Audio”
to “Bilingual,” bilingual audio is recorded.
• The main and sub audio will be simultaneously
recorded (VR mode). You can select audio modes
during playback.
It has already appeared, proceed to step 3.
3 Select “Recording” using
[Cursor U/ D], then press [ENTER].
DVD to VCR
4 Select “Dubbing Mode” using
[Cursor U/ D/ L / P], then press
[ENTER].
5 Select “DVD→VCR” using
[Cursor U/ D], then press [ENTER].
Option window will appear.
Dubbing Mode
VCR DVD
VCR to DVD
VCR DVD
DVD VCR
5 Select “VCR→DVD” using
[Cursor U/ D], then press [ENTER].
Dubbing Mode
VCR DVD
VCR DVD
DVD VCR
6 Press [SETUP] to exit the setting
menu.
7 Press [VCR
].
Make sure to select a recording speed using
[REC SPEED]. (See page 63)
6 Press [SETUP] to exit the setting
8 Press [DVD ].
menu.
9 Press [PLAY P] on the unit, and then
press [PAUSE p] at the point you
wish to start recording.
7 Press [DVD ].
Make sure to select a recording speed using
[REC SPEED]. (See page 22.)
8 Press [VCR
].
33
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 34 Thursday, March 31, 2005 10:04 PM
10 Press [DUBBING].
DVD to VCR duplication will start.
Finalising discs
11 Press [STOP S] to stop the
Video
DVD-RW
VR
DVD-RW
recording.
DVD-R
You will need to finalise discs to play them back in
other players.
Note
Finalising may take from several minutes up to an
hour. (A disc recorded in Video mode can take up to
15 minutes. A disc recorded in VR mode can take up
to 60 minutes.)
A shorter recording period on the disc will require a
longer time period for finalisation. Do not unplug the
mains cable during finalisation.
• When you turn off the unit after setting the Dubbing
Mode to DVD→VCR, the setting will be set to
VCR→DVD automatically.
• Dubbing Mode is available only if the tape or disc is
not copy protected.
• You cannot change the output mode during VCR to
DVD or DVD to VCR duplication.
Insert a recordable disc before
finalising.
Setting a disc to protect
VR
1 In stop mode, press [SETUP].
DVD-RW
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
To prevent accidental over-recording, editing or
erasing of recordings, you can protect them using the
Setting menu.
2 Select “Disc” using [Cursor U/ D],
then press [ENTER].
Insert a recordable disc.
3 Select “Finalise” using
1 In stop mode, press [SETUP].
[Cursor U/ D], then press [ENTER].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
4 Select “Yes” using [Cursor U/ D],
then press [ENTER].
2 Select “Disc” using [Cursor U/ D],
Finalising will start.
then press [ENTER].
DVD
Finalise
3 Select “Disc Protect OFF → ON”
using [Cursor U/ D], then press
[ENTER].
Yes
No
4 Select “Yes” using [Cursor U/ D],
then press [ENTER].
The disc is protected.
Note
• The Disc Protect setting is available only when a
disc recorded in VR mode is inserted.
• You can select only “Disc Protect ON → OFF” when
To cancel finalising (DVD-RW only):
a protected disc is inserted.
At step 4, press [STOP S], select “Yes,” then
press [ENTER]. Finalising is cancelled and the
unit switches to stop mode.
To cancel the disc protect:
• Select “Disc Protect ON → OFF” at step 3, then
select “Yes.”
• If you insert a disc protected with this unit, “Disc
Protect ON → OFF” will appear instead of “OFF →
ON.”
Do you want to cancel ?
Yes No
Finalising
10%
EN
34
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 35 Thursday, March 31, 2005 10:04 PM
If
appears when [STOP S] is pressed, you
Note
cannot cancel finalising because the finalising has
• Auto finalise function is not available for discs
formatted in VR mode.
already reached at a critical point in its process.
If “No” is selected and [ENTER] or
[RETURN R] pressed, finalising is continued.
You cannot cancel finalising a DVD-R disc once it
has started.
5 Finalising is complete.
Hint
• Finalising a disc in Video mode automatically
creates a title menu.
• You can use the unit to record or edit a disc
recorded in VR mode even after it is finalised. After
you finalise a disc recorded in Video mode, you
cannot edit or record anything else on that disc.
• To reverse the finalisation of the disc, select “Undo
Finalise” at step 3.
Note
• If you insert a DVD-RW disc finalised with this unit,
“Undo Finalise” will appear instead of “Finalise.”
• DO NOT power off during finalising. This may result
in a malfunction.
Auto finalise
Video
DVD-RW
DVD-R
You can finalise discs automatically when the disc
space runs out if you set this in the Setting menu.
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3 Select “Recording” using
[Cursor U/ D], then press [ENTER].
4 Select “Auto Finalise” using
[Cursor U/ D], then press [ENTER].
Recording
DVD
DVD-RW Recording Format
Auto Chapter
Video mode
10 minutes
Timer Programming
Auto Finalise
Bilingual Recording Audio
Main
External input Audio
Dubbing Mode
Stereo
VCR DVD
5 Press [ENTER].
6 Select “ON” using [Cursor U/ D],
then press [ENTER].
7 Press [SETUP] to exit.
35
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 36 Thursday, March 31, 2005 10:04 PM
Playing back discs
is a trademark of DVD Format / Logo
Licensing Corporation.
Information on playing back
DVDs
Colour systems
Read the following information before you play back a
DVD.
DVDs are recorded using different colour systems
throughout the world. The most common colour
system, used primarily in the U.K. and other EU
countries, is PAL.
Playable discs
This unit uses the PAL system. However, it is also
possible to play back DVDs using other colour
systems, such as NTSC.
You can play back all the discs listed below in this unit.
Before attempting to play back a DVD, make sure it
meets the requirements for Region Codes and Colour
Systems as described in this section. Discs that bear
any of the logos shown below will be played back
correctly in this unit. Other Disc types are not
guaranteed to be played back.
Region codes
This unit has been designed to play back DVDs within
Region Two (2). It is only possible to play back DVDs
in this unit that are labelled for Region 2 or for ALL
regions. You cannot play back DVDs that are labelled
for other regions. Look for DVDs that bear either of the
symbols shown below. If these region symbols do not
appear on your DVD, you cannot play back the DVD in
this unit.
Disc
Logo
DVD-Video
DVD-RW (VIDEO/VR mode)
DVD-R (VIDEO mode)
DVD+RW*
The number inside the globe refers to region of the
world.
A DVD labelled for a specific region can only be
played back in the unit with the same region code.
DVD+R*
Hint for DVD playback
CD-DA (AUDIO CD)
The contents of a DVD are generally divided into
titles. Titles are sometimes further subdivided into
chapters.
DIGITAL VIDEO
VCD (VIDEO CD)
Start Rec.
Stop/Start
Stop Rec.
Title 1
Title 2
CD-RW
(CD-DA FORMAT, MP3, JPEG files)
Chapter 1 Chapter 2 Chapter 3
Chapter 1 Chapter 2
CD-R
(CD-DA FORMAT, MP3, JPEG files)
Kodak Picture CD
* There may be a disc which cannot be used or played
back.
EN
36
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 37 Thursday, March 31, 2005 10:04 PM
Note
• Some discs may start playback automatically.
Basic playback
Playing back a DVD-V / CD / Video CD
Playing back a DVD-RW / DVD-R /
DVD+RW / DVD+R disc
DVD-V
CD
Video
DVD-RW
VR
DVD-RW
1 Follow steps 1 to 5 in “Playing back a
DVD-RW / DVD-R / DVD+RW / DVD+R
disc.”
DVD-R
DVD+RW
DVD+R
1 Press [STANDBY-ON] to turn on the
2 Press [PLAY P] to start playback.
unit.
Playback will start.
To play back a DVD, turn the TV on and be sure to
select the input to which the unit is connected.
If you are playing back a DVD-Video or a Video
CD, a menu may appear.
See pages 38 - 40 for details.
2 Press [DVD ].
3 Press [OPEN / CLOSE / EJECT O] to
3 Press [STOP S] to stop playback.
open the disc tray.
Playing back an MP3 / JPEG
4 Place the disc on the disc tray with
its label facing up. Be sure to align
the disc with the disc tray guide.
MP3
JPEG
1 Follow steps 1 to 5 in “Playing back a
DVD-RW / DVD-R / DVD+RW / DVD+R
disc.”
2 In stop mode, press [TOP MENU] and
Disc tray
guide
select the MP3 / JPEG menu.
File List
DISC NAME
5 Press [OPEN / CLOSE / EJECT O] to
Folder 1
Folder 2
Folder 3
Folder 4
close the disc tray.
6 Press [TOP MENU] to display the title
1
2
3
4
File 1
File 2
File 1
File 2
menu.
You can switch between the “Original” and
“Playlist” in the VR mode using [MENU / LIST].
1/2
7 Select the desired title using
[Cursor U/ D/ L/ P], then press
[ENTER].
To exit the menu, press [TOP MENU] again.
3 Press [Cursor U/ D] to select the
desired folder (group) or track, then
press [ENTER].
Playback will start.
8 Press [STOP S] to stop playback.
If a track is selected:
Playback will start.
To eject the disc, press
[OPEN / CLOSE / EJECT O] to open the disc
tray, then remove the disc. Press
[OPEN / CLOSE / EJECT O] to close the disc
tray before turning off the unit.
If a folder is selected:
The files in the folder will appear.
Press [Cursor U/ D] to select the track or folder
you want, then press [ENTER].
Hint
• Press [PLAY P], [ENTER] or [Cursor P] to
move to any lower folders.
• Press [Cursor L] or [RETURN R] to move
back to the folder above.
• For DVD-R (Video mode) and DVD-RW (Video
mode) discs that are already finalised, a title list will
be displayed instead of thumbnails.
• If you insert a DVD-RW recorded in VR mode and it
has a Playlist, the Playlist is displayed.
• You can resume playback from where you stopped
playing back the disc (Resume playback).
See page 41 for details.
• Press [STOP S] to return to the first item.
Hints for MP3/JPEG files:
• Folders are known as Groups, files are known
as Tracks.
• Folders are shown with the
icon.
37
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 38 Thursday, March 31, 2005 10:04 PM
• MP3 files are shown with the
Playback will start from the selected track and
continue with each one after.
• JPEG files are shown with the
• The unit can recognize up to 255 groups (or
folders) and up to 255 tracks.
• The name of each group and track can be
displayed using up to 29 characters.
Unrecognisable characters are replaced with
asterisks.
• Unplayable groups and tracks may be displayed
depending on the recording conditions.
• For MP3 file recorded in Variable Bit Rate
(VBR), the unit may not display the actual
elapsed time.
• If there are no files in the folder, “No Files” is
displayed.
• High resolution or large-size JPEG files take a
few moments to be displayed.
icon.
Kodak Picture CD
The Picture CD is a service to convert photographs
taken by a conventional film camera into digital data
and write the data on a CD. You can enjoy picture
images on the TV set by playing back the Picture
CDs.
For details of Kodak Picture CD, contact a shop that
provides developing service of Kodak Inc.
icon.
Press [DVD
] first.
1
Press [TOP MENU].
PictureCD
3
6
2
5
1
4
• It is not possible to play back progressive
JPEGs (JPEG files saved in progressive format)
on this unit.
• It is not possible to play back JPEG files of 2.2
MB or more.
• To exit the Picture CD thumbnail List, press
[TOP MENU] again or press [STOP S].
It is recommended that files to be played back in
this unit are recorded under the following
specifications:
If all menu items cannot be displayed in the
screen scope, the
and the
appear at the right bottom
appear at the left bottom of the
[MP3]
screen and you can view other items on the next
or previous page. The track number of the items
currently played back is highlighted.
• Sampling frequency: 44.1 kHz or 48 kHz.
• Constant Bit Rate: 112 kbps to 320 kbps.
If the
is shown at the right bottom, use
[Cursor P] to view the next page. If the
is
[JPEG] Size of picture
shown at the left bottom, use [Cursor L] to view
the previous page.
It may take some time until all menu items are
displayed on the menu screen.
• Upper limit: 6300 x 5100 dots
• Lower limit: 32 x 32 dots
• Capacity limit: less than 2.2 MB
2
3
Press [Cursor U/ D/ L / P] to select a
Hint
desired track to be played back, then
• During JPEG playback, press [Cursor P] or
[Cursor L] to rotate a picture 90 degrees clockwise
or counterclockwise respectively. (Not available
when the display menu appears.)
press [PLAY P] or [ENTER].
An image will be played back from the selected
track and go to the next one in turn.
Press [STOP S] to stop playback.
Notes on JPEG and Kodak Picture CD:
After track is displayed for 5 seconds or 10
seconds (set in the “Slide Show”) the display
moves to the next track.
During JPEG or Kodak Picture CD playback,
press [Cursor P] or [Cursor L] to rotate a
picture 90 degrees clockwise or
Note
• MP3 files cannot be recorded as digital sound using
an MD or DAT deck.
• Files with extensions other than “.mp3 (MP3)” or
“.jpg / .jpeg (JPEG)” will not be listed in the File List.
• Some folders or tracks listed in the File List may be
unplayable due to their recording status.
• The File List displays only up to 8 folder and file
names.
counterclockwise respectively. (Not available
when the display menu appears.)
Playing back discs using the disc
menu
DVD-V
A DVD contains a disc menu, which lists the contents
and enables you to customize playback. The menu
may offer choices for subtitle languages, special
features, and chapter selection. Usually this
information appears automatically when you start
playback, but sometimes you need to press
[MENU / LIST] to display the menu.
Press [DVD ] first.
EN
38
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 39 Thursday, March 31, 2005 10:04 PM
1 Press [MENU / LIST].
Note
If the feature is not available,
the TV screen.
may appear on
• [TOP MENU] will not be available for some DVDs.
• Menus vary among discs. Refer to the information
accompanying the disc for details.
2 Select an item using
[Cursor U/ D/ L/ P], then press
[ENTER].
Repeat this step until all the features you want are
set up or to start playing back the disc from the
menu. The following operations are available.
[MENU / LIST] button:
Displays the DVD menu, which will vary among
discs, and may be same with the Title menu.
[Cursor U/ D/ L/ P] buttons:
Move the cursor from item to item on the screen.
[ENTER] button:
Selects the currently highlighted menu option.
[the Number buttons]:
Selects a numbered menu option (available on
certain discs).
3 Press [MENU / LIST] to exit the disc
menu.
Note
• Menus vary among discs. Refer to the information
accompanying the disc for details.
Playing back a disc using the title
menu
DVD-V
Some DVDs have a title menu, which lists the titles
available on the DVD. You can start playing back such
discs at a specific title.
Press [DVD ] first.
1 Press [TOP MENU].
The title menu will appear.
If the feature is not available,
the TV screen.
may appear on
2 Select a desired item using
[Cursor U/ D/ L/ P], then press
[ENTER].
The disc will start playing back at the title you
selected. The following operations are available.
[TOP MENU] button:
Displays the DVD “Title menu” which will vary
between discs.
[Cursor U/ D/ L/ P] buttons:
Move the cursor from item to item on the screen.
[ENTER] button:
Selects the currently highlighted menu option.
[the Number buttons]:
Selects a numbered menu option (available on
certain discs).
3 Press [TOP MENU] to exit.
39
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 40 Thursday, March 31, 2005 10:04 PM
2 Select “CD Playback Mode” using
[Cursor U/ D], then press [ENTER].
PBC function for Video CDs
3 Select “PBC (Video CD only)” using
[Cursor U/ D], then press [ENTER].
VCD
This unit conforms to ver.1.1 and ver.2.0 of the Video
CD standard playback control (PBC) function. This
enables you to play back interactive software using
menu screens. Refer to the information
CD Playback Mode
Random Play
Program Play
accompanying the Video CD.
PBC(Video CD only)
Slide Show
OFF
Ver.1.1 (without PBC function): You can still enjoy
playback of pictures and music from the CD.
Ver.2.0 (with PBC function): “Pbc” will appear on the
screen and display when playing back a Video CD
with the PBC function.
5 sec.
Hint
• When playing back Video CDs with the PBC
function, “Pbc” is displayed instead of the playing
back time and current track indications on the front
panel display.
4 Select “OFF” using [Cursor U/ D],
then press [ENTER].
5 Press [SETUP] to exit.
Note
To recall the PBC function, select “ON” in step 4
above.
• Some operations cannot be performed unless the
function is cancelled either automatically or
intentionally by you.
Note
• Operations that are not available when the PBC
function is set to “ON” are indicated by the following
symbol in this manual:
• The default setting of “PBC (Video CD only)” is “ON.”
VCD
(PBC OFF)
Playing back a Video CD using the
title menu
VCD
1 When playing back a Video CD with
the PBC function, the title menu will
appear automatically.
2 Press [the Number buttons] to select
the desired title.
Playback will start at the selected title.
3 Press [RETURN R] to go back to the
title menu.
Note
• While the on-screen display appears, you cannot
perform steps 2 and 3.
Cancelling and Recalling the PBC
function
Insert a Video CD.
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
EN
40
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 41 Thursday, March 31, 2005 10:04 PM
Hint
• Forward / reverse speeds are indicated with icons as
follows.
Special playback
Forward (Approx. Speed):
x1.5:
x20:
x40:
Resume playback
Video
VR
DVD-RW
DVD-V
DVD+RW
JPEG
DVD-RW
DVD-R
VCD MP3
Reverse (Approx. Speed):
x5:
x20:
x40:
DVD+R
CD
(PBC OFF)
You can resume playback from the point where you
stopped it before.
Skipping TV commercials during
playback
1 During playback, press [STOP S].
Video
DVD-RW
VR
DVD-RW
DVD-V
DVD-R
The resume message will appear.
To skip TV commercials and enjoy recorded programmes
without any interruptions, press [CM SKIP]
2 Press [PLAY P].
.
In a few seconds, playback will resume from the
point at which you stopped it before. Even if you
turn off the unit, you can resume playback at the
same point after turning on the unit back.
1 During playback, press [CM SKIP].
Normal playback will start 30-second advanced
point from the point at which you press [CM SKIP]
Each time you press [CM SKIP], the start point
will move another 30 seconds forward and
playback resume automatically.
.
To cancel the resume playback and start playing
back the disc from the beginning:
Press [STOP S] twice while playback is stopped.
You can press [CM SKIP] up to 6 times (180
seconds).
Note
• For Video CDs, if you turn PBC on using the setting
menu, the resume function is cancelled.
• For MP3 and JPEG files, playback will resume from
the beginning of the track at which playback was
stopped.
Pause
Video
DVD-RW
VR
DVD-RW
DVD-V
DVD+RW
JPEG
DVD-R
VCD MP3
DVD+R
CD
Fast forward / Fast reverse
Video
DVD-RW
VR
DVD-RW
DVD-V
DVD-R
VCD MP3
1 During playback, press [PAUSE p].
DVD+RW
DVD+R
CD
Playback will pause with the sound muted.
2 Press [PLAY P] to resume playback.
1 During playback, press [f] or [r].
For JPEG files, playback will start from the
beginning of the track.
Each time you press [ f] or [r], the
approximate speed will change as follows.
To output sound from DVDs during fast
forward at x1.5 speed, set “Fast Forward with
Audio” to “ON” for the “Playback” setting in
the Advanced Setting menu.
Step by step playback
Video
VR
DVD-V
DVD-RW
DVD-RW
DVD-R
Fast forward or fast reverse playback across titles
(for DVDs) or tracks (for MP3) is not possible.
DVD+RW
DVD+R
VCD
FWD
REV
FWD
REV
FWD
REV
FWD
REV
FWD
REV
FWD
REV
Normal
speed
playback
1 During playback, press [PAUSE p].
2 Press [SKIP B/ F] repeatedly.
x40
x20
x5
x1.5
x20
x40
Each time you press [SKIP F], playback will go
forward one frame (or step) at a time with the
sound muted.
• For Audio CDs, approximate speed is fixed at x8
with sound.
• For Video CDs, approximate forward speeds are
x1.5, x8 and x16, and approximate reverse
speeds are x2, x8 and x16.
To go backward one frame (or step), press
[SKIP B].
• For MP3 files, approximate speed is fixed at x16.
• To return to playback at normal speed, press
[PLAY P].
Press and hold [SKIP F] to continue going
forward.
To continue going backward, press and hold
[SKIP B].
41
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 42 Thursday, March 31, 2005 10:04 PM
3 Press [PLAY P] to resume playback.
Note
• Only step by step forward is available when playing
back Video CDs.
2 Select the desired zoom factor to
zoom using [Cursor U/ D], then
press [ENTER].
The zoom area is displayed.
3 Select the desired zoom position
using [Cursor U/ D/ L / P], then
press [ENTER].
Slow forward / Slow reverse playback
Video
DVD-RW
VR
DVD-RW
Zoom playback will start.
DVD-V
DVD-R
Hint
DVD+RW
DVD+R
VCD
• To exit the zoom menu, press [ZOOM] at step 1.
• To cancel the zoom function, select x1.0 using
[Cursor U/ D], then press [ENTER].
1 During playback, press [PAUSE p],
then press [f] or [r].
Note
Each time you press [f] or [r], the
approximate speed change as follows. (The
sound will remain muted.)
• If selecting a smaller factor than that currently
selected, the zoom area is not displayed.
• You cannot slide the zoomed picture on some JPEG
files.
FWD
FWD
FWD
FWD
FWD
FWD
Pause
REV
REV
REV
REV
REV
REV
x1/4
x1/8
x1/16
x
1/16
x1/8
x
1/2
Marker Setup
Video
DVD-RW
VR
DVD-RW
To return to normal playback, press [PLAY P].
Hint
DVD-V
DVD-R
VCD
DVD+RW
DVD+R
CD
(PBC OFF)
• Forward / reverse speeds are indicated with icons as
follows.
Forward (Approx. Speed):
x1 / 16:
You can assign a specific point on a disc to return
later.
x1 / 8:
x1 / 2:
1 During playback, press [DISPLAY].
Reverse (Approx. Speed):
2 Select the
icon using
x1 / 16:
x1 / 8:
x1 / 4:
[Cursor L/ P], then press [ENTER].
Marker setup menu for DVD-Video mode
Note
1
1
0:00:00
DVD-Video
• Only slow forward is available when playing back
Video CDs.
Zoom
Video
DVD-RW
VR
DVD-RW
DVD-V
DVD-R
JPEG
Marker setup menu for Audio CD mode
1
0:00:00
Audio CD
DVD+RW
DVD+R
VCD
1 During playback, press [ZOOM].
1
1
0:00:00
DVD-Video
1.2
1.5
2.0
3 Select the desired marker number
using [Cursor U/ D]. When the disc
reaches the desired point, press
[ENTER].
Four options are available, x1.0, x1.2, x1.5 and
x2.0. These are displayed excluding the current
zoom rate.
The title (track) number and the time are
displayed.
Hint
• You can also select the zoom function by pressing
[DISPLAY]. In this case, press [DISPLAY] first,
4 To return to the marker later, select
the desired marker number using
[Cursor U/ D], then press [ENTER].
select the
icon using [Cursor L / P], and then
press [ENTER].
EN
42
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 43 Thursday, March 31, 2005 10:04 PM
Hint
• To clear a marker, select the marker number you
wish to clear, then press [CLEAR].
• You can mark up to 6 points.
Search
Title / Chapter search
Video
Note
VR
• All markers are erased when you perform the
following operations.
DVD-V
DVD-RW
DVD-RW
DVD-R
- Open the disc tray.
- Turn off the power.
DVD+RW
DVD+R
- Record on a recordable disc.
- Change the mode between Original and Playlist.
(VR mode)
Using [SKIP B/ F] buttons
1 During playback, press [SKIP F] to
skip the current title or chapter and
move to the next.
The unit moves to the next title or chapter one
after the other.
To go back to the previous title or chapter, press
[SKIP B] repeatedly.
Using the [DISPLAY] button
1 During playback, press [DISPLAY].
2 Select the
icon using
[Cursor L/ P], then press [ENTER].
for the title number is highlighted.
Searching for a Title:
3 Enter the desired title number to
search for using [Cursor U/ D] or
[the Number buttons], then press
[ENTER].
Title search will start.
Hint
• Total number of chapters and playback time of the
selected title are also displayed.
Searching for a Chapter:
3 Press [Cursor L/ P] to highlight the
number displayed in the right side of
the
icon.
4 Enter the desired chapter number to
search for using [Cursor U/ D] or
[the Number buttons], then press
[ENTER].
Chapter search will start.
Hint
• The title number and playback time of the selected
chapter are also displayed.
43
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 44 Thursday, March 31, 2005 10:04 PM
Track search
Time search
Video
DVD-RW
VR
DVD-RW
MP3
JPEG
CD
VCD
(PBC OFF)
DVD-V
DVD-R
VCD
DVD+RW
DVD+R
CD
(PBC OFF)
Using [SKIP B/ F] buttons
1 During playback, press [DISPLAY].
icon using
1 During playback, press [SKIP F] to
skip the current track and move to
the next.
2 Select the
[Cursor L/ P], then press [ENTER].
The unit moves to the next track one after the
other.
for the title or track number is highlighted.
To go back to the previous track, press
[SKIP B] repeatedly. The unit moves backward
one track at a time.
3 Press [Cursor L/ P] to highlight
.
4 Enter the desired time to search for
using [Cursor U/ D] or
[the Number buttons], then press
[ENTER].
Using the [DISPLAY] button
1 During playback, press [DISPLAY].
Time search will start.
2 Select the
icon using
[Cursor L/ P], then press [ENTER].
Hint
• For Video CDs, you can perform the time search
function in stop mode without turning PBC OFF
manually.
for the track number is highlighted.
3 Enter the desired track number to
search for using [Cursor U/ D] or
[the Number buttons], then press
[ENTER].
Note
• During Random playback or Program playback, you
cannot search the desired time.
• The title number and chapter number of the setting
time are also displayed.
• Time search function is available only in the same
track or title.
• If the time search is not available, – –:– –:– – / – –:–
–:– – (or 0:00:00 / 0:00:00) is displayed.
Track search will start.
Hint
• For Video CDs, you can perform the track search
function in stop mode without turning PBC OFF
manually.
Note
• During Random playback or Program playback, you
cannot search the desired track.
Direct Search
CD
You can search the desired track directly.
Using [the Number buttons]
1 During playback, if the display menu
is not displayed, press
[the Number buttons] to enter the
desired track number.
Note
• During Random playback or Program playback, you
cannot search the desired track directly.
EN
44
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 45 Thursday, March 31, 2005 10:04 PM
Random playback
Repeat / Random / Program
playback / Slide Show
CD
VCD
(PBC OFF)
MP3
JPEG
You can use this function to play back a disc randomly
instead of in the recorded order.
Repeat playback
Video
VR
DVD-RW
1 In stop mode, press [SETUP].
DVD-V
DVD+RW
JPEG
DVD-RW
DVD-R
VCD MP3
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
DVD+R
CD
(PBC OFF)
2 Select “CD Playback Mode” using
[Cursor U/ D], then press [ENTER].
The CD Playback Mode menu will appear.
1 During playback, press [DISPLAY].
icon using
2 Select the
3 Select “Random Play” using
[Cursor U/ D], then press [ENTER].
Random playback will start.
[Cursor L/ P], then press [ENTER].
3 Select the desired option to repeat
using [Cursor U/ D], then press
[ENTER].
Hint
• To cancel random playback, press [STOP S] twice
during random playback. “Play mode OFF” appears
on the screen.
The selected repeat playback will start.
The following operations are available.
• For Video CDs, if you select random playback with
the PBC function on, the PBC function will be turned
off automatically and random playback starts.
Title:
The current title will be played back repeatedly.
(DVD only)
Chapter:
Note
The current chapter will be played back
• During random playback, if you forward the track to
the end, the playback speed of the next track will be
normal.
• During random playback, you cannot use the search
function except for the search with [SKIP B/ F].
By pressing [SKIP B], you can return only to the
beginning of the current track.
repeatedly.
(DVD only)
All:
The current disc will be played back repeatedly.
(DVD-RW (VR mode), CD, Video CD, MP3 and
JPEG only)
A-B:
The A-B point will be played back repeatedly.
(DVD, CD and Video CD only)
When pressing [ENTER] while A-B is highlighted,
A-B repeat is set.
• Press [ENTER] again to decide the starting
point (A).
Program playback
CD
VCD
(PBC OFF)
You can programme the disc to play back in your
desired order.
• Press [ENTER] after setting point (A) to select
the ending point (B).
1 Follow steps 1 and 2 in “Random
Track:
playback.”
The current track will be played back repeatedly.
(CD, Video CD, MP3 and JPEG only)
2 Select “Program Play” using
Group:
[Cursor U/ D], then press [ENTER].
The current group will be played back repeatedly.
(MP3 and JPEG (except Picture CD) only)
Program Play
Hint
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
• To cancel the repeat playback, select “OFF” at step
3. The repeat setting is also cancelled when you
stop playback.
Note
• You can only set A-B repeat playback within the
current title (for DVDs) or current track (for Audio
CDs and Video CDs).
Total 0:00:00
• You cannot select “Group” during the random
playback of MP3 files.
45
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 46 Thursday, March 31, 2005 10:04 PM
3 Select the desired track using
[Cursor U/ D], then press [ENTER]
or [Cursor P].
Selecting the format of audio
and video
You can select the format of audio and video to suit
the content of the disc you are playing back.
4 Press [PLAY P] to start program
playback.
Hint
• To erase tracks you selected, press [CLEAR].
• You can make up to 50 track settings.
• To cancel program playback, press [STOP S] twice
during program playback. “Play mode OFF” appears
on the screen.
• You may also select the desired track using
[the Number buttons] at step 3.
• For Video CDs, if you select program playback with
the PBC function on, the PBC function will be turned
off automatically and program playback starts.
Switching subtitles
VR
DVD-V
DVD-RW
Many DVD-Videos have subtitles in one or more
languages. The languages available are usually
printed on the disc case. You can switch subtitle
languages at any time during playback.
1 During playback, press [DISPLAY].
Note
2 Select the
icon using
[Cursor L/ P], then press [ENTER].
• During programme playback, if you forward the track
to the end, the playback speed of the next track will
be normal.
• During programme playback, you cannot use the
search function except for the search with
[SKIP B / F].
3 Select the desired subtitle language
using [Cursor U/ D], then press
[ENTER].
Subtitles are displayed in the selected language.
If you select “OFF,” subtitles will disappear.
Slide Show
Note
JPEG
• With some discs it is only possible to change the
subtitle language from the disc menu. Press
[TOP MENU] or [MENU / LIST] to display the disc
menu.
• If a 4-digit language code appears in the subtitle
menu at step 2, refer to the “Language code” on
page 70.
You can select the display time between 5 seconds
and 10 seconds.
1 Follow steps 1 and 2 in “Random
playback.”
2 Select “Slide Show” using
Switching audio soundtrack
VR
[Cursor U/ D], then press [ENTER].
DVD-V
DVD-RW
CD
VCD
MP3
3 Select the display time using
[Cursor U/ D], then press [ENTER].
When playing back a DVD-Videos recorded with two
or more soundtracks (often in different languages),
you can switch among them during playback.
When playing back DVD-RW discs recorded in VR
mode, you can switch to main audio (L), sub audio (R)
or a combination of both (L / R).
Note
• Large-size JPEG files take a few moments to be
displayed.
When playing back Audio CDs, Video CDs or MP3
files, you can switch among the left, the right channel,
and stereo.
1 During playback, press [DISPLAY].
Press [AUDIO] during playback, and follow from
step 3.
2 Select the
icon using
[Cursor L/ P], then press [ENTER].
EN
46
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 47 Thursday, March 31, 2005 10:04 PM
3 Select a desired audio soundtrack or
audio channel using [Cursor U/ D],
then press [ENTER].
3 Select the desired option using
[Cursor U/ D], then press [ENTER].
This function reduces noise in the playback picture.
When playing back discs recorded in long time modes
such as 8H or 10H, select “Type 1” or “Type 2.” “Type
2” is more effective.
When playing back discs with a little noise, such as
DVD-Videos, select “OFF.”
With a DVD Video:
Audio soundtrack will switch.
Example:
English → Spanish → French
With a DVD-RW in VR mode:
Audio channel menu will appear.
Follow the step 4.
With an Audio CD, Video CD, or MP3 files:
The Audio channel will switch.
Example:
STEREO → L-ch → R-ch
4 Select the desired audio channel
using [Cursor U/ D], then press
[ENTER].
The Audio channel will switch.
Note
• With some discs it is only possible to change the
soundtrack from the disc menu. Press [TOP MENU]
or [MENU / LIST] to display the disc menu.
Switching camera angles
DVD-V
Some DVD-Videos feature scenes shot from two or
more angles. The disc case is usually marked with an
angle icon if the disc has multi-angle scenes.
1 During playback, press [DISPLAY].
The angle icon appears when a switching camera
angle is available. (Available only when the angle
icon appears in bottom right on the TV screen.)
2 Select the
icon using
[Cursor L/ P], then press [ENTER].
The angle will switch each time you press
[ENTER].
Hint
• Even when the
icon is not displayed, you can
select the angle if the currently played back title has
at least two multi-angle scenes.
Reducing block noise
Video
VR
DVD-V
DVD-RW
DVD-RW
DVD-R
DVD+RW
DVD+R
VCD
1 During playback, press [DISPLAY].
icon using
2 Select the
[Cursor L/ P], then press [ENTER].
The Noise Reduction menu will appear.
47
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 48 Thursday, March 31, 2005 10:04 PM
Editing
Disc editing
You can edit a disc recorded using the PAL system. It
is not possible to edit discs recorded using the NTSC
system.
Editing discs in Video mode
You can edit the following disc items in Video mode.
• Deleting titles (See below.)
• Editing titles (See page 49.)
• Setting or clearing chapter markers (See page 50.)
Guide to a title list
Note
• After a disc is finalised, editing the disc or recording
on the disc is not possible. (Except DVD-RW discs in
VR mode.)
• A Playlist is not available for DVD-R or DVD-RW
discs in Video mode.
The title list enables you to check the titles recorded
on a disc easily. You can choose a title to play back
from the screen and easily edit the titles as you wish.
The items on the title list are as follows.
• It is not possible to edit a disc recorded in another
video system other than PAL, such as NTSC.
Original
Insert a recordable disc.
3
6
2
5
1
15/04 19:00 P12 1H
4
Deleting titles
Video
DVD-RW
DVD-R
You can delete titles you do not want to keep.
In Video mode, recordable disc space of DVD-RW
disc will increase when the last title on the title list is
deleted. However, deleting the title will not change
recordable disc space for DVD-R disc.
3
1
2
In finalised DVD-R discs or DVD-RW (in Video mode),
you cannot select the title list because it cannot be
edited once finalised.
Original
TitleDelete
3
Protect
Note
• It is not possible to retrieve deleted titles.
Press [DVD ] first.
15/0419:00 P12 1H
1 In stop mode, press [SETUP].
0:00:59
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
8 7
6
5
4
2 Select “Disc” using [Cursor U/ D],
then press [ENTER].
1
2
To select a title recorded on the disc for editing,
move the cursor to the title and press [ENTER].
If the title is protected, the Protect icon will
appear.
3 Select “Title List” using
[Cursor U/ D], then press [ENTER].
• It is not possible to protect a title on the Playlist.
Arrow icons mean the title list includes a next or
previous page. Press [Cursor L/ P] in the
direction of the icon you wish to follow.
Available title editing menu items vary depending
on the disc and format types.
Disc
3
Title List
Format
Finalise
4
5
6
You can edit the title and details as you wish.
Time status bar of the recording.
• After editing, playback starts from this point.
The selected title from the title list thumbnails.
• The selected title is played back automatically.
Playback status of the current disc.
7
8
EN
48
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 49 Thursday, March 31, 2005 10:04 PM
4 Select the desired title using
[Cursor U/ D/ L/ P], then press
[ENTER].
3 To enter the title name, refer to
“Guide to editing title names” on this
page.
Title List
Title List
Edit Title Name
3
6
2
5
1
6
A
a
1
B
b
2
!
C
c
3
@
?
15/0419:00 P12 1H
4
15/04 19:00 P12 1H
0:00:59
When you finish entering the title name, press
[ENTER].
5 Select “Title Delete” using
[Cursor U/ D], then press [ENTER].
4 Select “Yes” using [Cursor U/ D],
then press [ENTER].
Title List
Title Delete
6
The name you edited becomes for the title.
Edit Title Name
Chapter Mark
5 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
15/04 19:00 P12 1H
0:00:59
Guide to editing title names
Step 1: Select the desired character set using
[Cursor U/ D], then press [ENTER].
You cannot select “Chapter Mark” when a DVD-R
disc is inserted into the unit. For DVD-RW discs in
Video mode, you cannot select the chapter mark
of the title which is less than 5 minutes.
Step 2: Using the list below as a guide, press
[the Number buttons] repeatedly until the
desired letter appears.
6 Select “Yes” using [Cursor U/ D],
then press [ENTER].
Select
ABC
abc
123
@ ! ?
Press
0
The title is deleted.
<space> <space>
<space>
0
Title List - Title Delete
! ” # $ % & ’ ( )
Yes
No
6
—
—
1
+ , - . / : ; < = >
1
*
? @ [ ] ^ _ { | }
—
—
—
—
—
—
—
—
2
3
4
ABC
DEF
abc
def
2
3
4
5
6
7
8
9
15/0419:00 P12 1H
GHI
ghi
0:00:59
JKL
jkl
5
6
MNO
PQRS
TUV
mno
pqrs
tuv
7 Press [SETUP].
7
8
Writing on the disc starts.
It may take a while to write the data on a disc.
WXYZ
wxyz
9
• Characters set will be changed to the “@!?”
automatically if you press [1] after you selected the
“ABC” or “abc” mode.
Editing titles
Video
DVD-RW
DVD-R
You can edit the title names from this menu.
The title names you edit will appear on the title list.
Note
• To delete letters, press [CLEAR] repeatedly. Press
and hold [CLEAR] to delete all letters.
• To move on to the next set of letters, press
[Cursor P].
Press [DVD ] first.
1
Follow steps 1 to 4 in ”Deleting titles.”
• You can enter up to 30 letters.
2 Select “Edit Title Name” using
[Cursor U/ D], then press [ENTER].
A window for entering the title name will appear.
49
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 50 Thursday, March 31, 2005 10:04 PM
• Unrecognisable characters will be replaced with
asterisks (*). If you delete them, adjoining
characters may change to asterisks (*) or other.
8 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
Setting or clearing chapter markers
• You cannot select a chapter marker interval that
exceeds the length of a title.
• The length of chapters may slightly deviate from the
one specified at the step 6.
Video
DVD-RW
• A chapter marker may be delayed depending on the
recording content.
You can add chapter markers to a title. After a title is
marked with chapters, you can use the chapter search
feature.
You can specify the interval of chapter markers for
titles last more than 5 minutes.
Press [DVD ] first.
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
2 Select “Disc” using [Cursor U/ D],
then press [ENTER].
3 Select “Title List” using
[Cursor U/ D], then press [ENTER].
4 Select the desired title using
[Cursor U/ D/ L/ P], then press
[ENTER].
5 Select “Chapter Mark” using
[Cursor U/ D], then press [ENTER].
6 Select the desired interval using
[Cursor U/ D], then press [ENTER].
Title List
Chapter Mark
OFF
5 minutes
6
10 minutes
15 minutes
30 minutes
60 minutes
15/0419:00 P12 2H
1:00:59
7 Select “Yes” using [Cursor U/ D],
then press [ENTER].
Title List
Chapter Mark
5minutes
Yes
No
6
15/0419:00 P12 2H
1:00:59
Chapter markers are added.
If you select “OFF” at step 6, all the chapter
markers are erased.
EN
50
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 51 Thursday, March 31, 2005 10:04 PM
Editing discs in VR mode
For discs in VR mode, you can edit from the “Original”
menu or the “Playlist” menu that you create from the
original.
Original Editing Original titles
in VR mode
Insert a recordable disc before editing.
Editing original titles Original
You can perform the following operations on the
Deleting titles
Original
VR
original titles.
DVD-RW
• Deleting titles (See this page.)
• Protecting titles (See page 52.)
• Releasing titles from protecting (See page 52.)
When a title is deleted from an original list in VR
mode, the available recording time on the disc will
increase.
Note
Editing playlists Playlist
• It is not possible to retrieve deleted titles.
You can create a Playlist from original titles, and edit it
to your preference without losing the original titles.
You can perform the following operations on the
Playlist.
• Deleting titles (See page 53.)
• Deleting parts of titles (Scene Delete) (See page
53.)
Press [DVD ] first.
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
• Editing titles (See page 54.)
2 Select “Disc” using [Cursor U/ D],
• Setting or clearing chapter markers (See page 54.)
• Setting pictures as thumbnails (See page 55.)
• Dividing a title (See page 55.)
• Combining titles (See page 55.)
• Adding titles to a Playlist (See page 56.)
• Deleting a Playlist (See page 56.)
then press [ENTER].
3 Select “Original” using
[Cursor U/ D], then press [ENTER].
Disc
Playlist
Note
Original
• After editing, titles will not remain as recorded
originally. If you want to keep the original as it is, edit
the Playlist to your preference.
Format
Finalise
Disc Protect OFF ON
4 Select the desired title using
[Cursor U/ D/ L/ P], then press
[ENTER].
5 Select “Title Delete” using
[Cursor U/ D], then press [ENTER].
Original
TTitleDelete
3
Protect
15/0419:00 P12 1H
0:00:59
6 Select “Yes” using [Cursor U/ D],
then press [ENTER].
The title is deleted.
7 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
• When you delete the original title, the corresponding
part of the playlist will also be deleted.
51
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 52 Thursday, March 31, 2005 10:04 PM
Protecting titles
Releasing titles from
Original
Original
VR
DVD-RW
protecting
VR
To prevent the accidental editing or erasing of the
titles, you can protect them in the original menu.
DVD-RW
You can cancel the title protection feature after it is
applied.
Press [DVD ] first.
Press [DVD ] first.
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
1 Follow steps 1 to 4 in
“
Original Protecting titles.”
2 Select “Disc” using [Cursor U/ D],
2 Press [ENTER].
then press [ENTER].
Original
Protect
3 Select “Original” using
[Cursor U/ D], then press [ENTER].
ON OFF
3
4 Select the desired title using
[Cursor U/ D/ L/ P], then press
[ENTER].
15/0419:00 P12 1H
5 Select “Protect” using
0:00:59
[Cursor U/ D], then press [ENTER].
Original
3 Press [ENTER] again.
The key icon will disappear from the title in the
original list.
Title Delete
3
Protect
4 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
15/0419:00 P12 1H
0:00:59
6 Press [ENTER] again.
Original
Protect
OFF ON
3
15/04 19:00 P12 1H
0:00:59
7 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
To protect a whole disc (DVD-RW VR mode
only):
Select “Disc Protect” from the Disc menu, then
select “Yes.” Refer to “Setting a disc to protect” on
page 34.
Hint
• The protected title is marked with a key icon in the
original list.
EN
52
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 53 Thursday, March 31, 2005 10:04 PM
Deleting parts of titles
(Scene Delete)
VR
Playlist
Playlist Editing the Playlist in
VR mode
DVD-RW
You can delete a specific part of a title.
Even when a title is deleted from the playlist, the
original title will remain.
The available recording time on the disc will not
increase.
Note
• When you play back the disc of which the playlist is
edited, select “Playlist” in the title menu.
Insert a recordable disc before editing.
Press [DVD ] first.
Deleting titles
Playlist
VR
DVD-RW
1 Follow steps 1 to 4 in
“Playlist Deleting titles.”
In VR mode, even when a title is deleted from the
Playlist, the original title will remain in the Original list.
The recordable disc space to record will not increase.
2 Select “Scene Delete” using
[Cursor U/ D], then press [ENTER].
3 Use [SKIP B/ F], [r], [f],
[PLAY P] and [PAUSE p] to find the
start point, then press [ENTER].
Press [DVD ] first.
1 In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
Playlist Scene Delete
2 Select “Disc” using [Cursor U/ D],
Start
3
End
then press [ENTER].
Preview
Delete
3 Select “Playlist” using
[Cursor U/ D], then press [ENTER].
Use [SKIP B/ F], [r], [f],
[PLAY P] and [PAUSE p] again to
move to the end point, and press
[ENTER].
4 Select the desired title using
[Cursor U/ D/ L/ P], then press
[ENTER].
5 Select “Title Delete” using
Playlist Scene Delete
[Cursor U/ D], then press [ENTER].
Start
3
End
Playlist
Preview
Delete
TitleDelete
3
Scene Delete
Edit Title Name
Chapter Mark
Index Picture
Title Dividing
Title Combining
The cursor will move to “Preview.” You can check
the preview by pressing [ENTER].
The bar at the bottom of the screen indicates the
total and the elapsed time of the title, and the area
selected for deletion is indicated in red during the
preview.
15/0419:00 P12 1H
0:00:59
4 Select “Delete” using
[Cursor U/ D], then press [ENTER].
6 Select “Yes” using [Cursor U/ D],
then press [ENTER].
5 Select “Yes” using [Cursor U/ D],
The title is deleted.
then press [ENTER].
The part of the title is deleted.
7 Press [SETUP].
Writing on the disc starts.
6 Press [SETUP].
It may take a while to write the data on a disc.
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
• You cannot select “Scene Delete” if the number of
chapter markers in the Original or Playlist is more
than 900.
• The recordable disc space will not increase after
deleting parts of titles.
53
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 54 Thursday, March 31, 2005 10:04 PM
3 Use [SKIP B/ F], [r], [f],
[PLAY P] and [PAUSE p] to find the
point where you will create a new
chapter marker.
Editing titles
Playlist
VR
DVD-RW
You can edit the title names from this menu.
The names you edit will appear on the title list.
Or, use [SKIP B/ F] to find a
chapter marker that you wish to
delete.
Press [DVD ] first.
1 Follow steps 1 to 4 in
4 Select “Add” or “Delete” accordingly
using [Cursor U/ D], then press
[ENTER].
“Playlist Deleting titles.”
2 Select “Edit Title Name” using
[Cursor U/ D], then press [ENTER].
ylist
aeMk
3 To enter the title name, refer to
“Guide to editing title names” on
page 49.
3
Chapter
2/
2
Playlist Edit Title Name
15/0419:00 P12 1H
6
A
a
1
B
b
2
!
C
c
3
@
?
You cannot delete the first chapter of a title.
5 Select “Yes” using [Cursor U/ D],
15/04 19:00 P12 1H
then press [ENTER].
0:00:59
Playlist
Chapter Mark
Add
When you finish entering the title name, press
[ENTER].
Yes
No
3
4 Select “Yes” using [Cursor U/ D],
then press [ENTER].
Chapter
2/
2
The name you edited becomes the title.
15/0419:00 P12 1H
5 Press [SETUP].
0:00:59
Writing on the disc starts.
It may take a while to write the data on a disc.
A chapter marker is added.
Adding a chapter marker:
If you select “Add” at step 4, a new chapter marker is
created at the point you specified.
Setting or clearing chapter
Playlist
markers
VR
Deleting a chapter marker:
DVD-RW
If you select “Delete” at step 4, the chapter marker
you selected is deleted.
You can add chapter markers to a title. After a title is
marked with chapters, you can use the chapter search
feature.
You can set a chapter marker anywhere you want.
You cannot set more than 999 chapter markers in the
Playlist.
6 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Press [DVD ] first.
1 Follow steps 1 to 4 in
“Playlist Deleting titles.”
2 Select “Chapter Mark” using
[Cursor U/ D], then press [ENTER].
EN
54
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 55 Thursday, March 31, 2005 10:04 PM
3 Select “Title Dividing” using
Setting pictures as
thumbnails
VR
Playlist
[Cursor U/ D], then press [ENTER].
4 Select “Yes” using [Cursor U/ D],
then press [ENTER].
DVD-RW
The title is divided into two new titles with the
same title names.
The thumbnail you set is reset to the first picture
of each title.
You can set a picture as a thumbnail for each title.
This helps you to remember the content of the title
without having to play it back. The first picture of the
title is selected as the default.
Press [DVD ] first.
Playlist
Title Dividing
1 Follow steps 1 to 4 in
Yes
No
3
“Playlist Deleting titles.”
2 Use [SKIP B/ F], [r], [f],
[PLAY P] and [PAUSE p] to find the
picture you want to set as a
15/0419:00 P12 1H
thumbnail, then press [ENTER].
0:00:59
3 Select “Index Picture” using
[Cursor U/ D], then press [ENTER].
5 Press [SETUP].
Writing on the disc starts.
4 Select “Yes” using [Cursor U/ D],
It may take a while to write the data on a disc.
then press [ENTER].
The picture is set as the thumbnail.
Note
• If a disc contains the maximum number of
recordings (99), you cannot divide any titles.
• You cannot divide the titles if the total number of the
chapters have already reached 999.
Playlist
Index Picture
Yes
No
3
Combining titles
Playlist
VR
DVD-RW
15/0419:00 P12 1H
You can combine two titles into a single title.
0:00:59
Press [DVD
] first.
5 Press [SETUP].
1 Follow steps 1 to 4 in
Writing on the disc starts.
“Playlist Deleting titles.”
It may take a while to write the data on a disc.
2 Select “Title Combining” using
[Cursor U/ D], then press [ENTER].
Note
• If a picture selected as a thumbnail is deleted by
deleting a part of a title, the default picture is
selected.
3 Select another title to combine using
[Cursor U/ D/ L/ P], then press
[ENTER].
Playlist Dividing a title
VR
DVD-RW
4 Select “Yes” using [Cursor L/ P],
then press [ENTER].
You can divide a title into two new titles.
The two titles will combine into a single title.
Playlist
Press [DVD ] first.
Playlist
Title Combining
Add New
Title
3
2
1
1
2
1+2
Delete
Playlist
1 Follow steps 1 to 4 in
04/15 19:00 P12 1H
Yes
No
“Playlist Deleting titles.”
2 Use [SKIP B/ F], [r], [f],
[PLAY P] and [PAUSE p] to find the
point where you wish to divide the
title.
Wait for a moment.
5 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
55
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 56 Thursday, March 31, 2005 10:04 PM
2 Select “Delete Playlist” using
[Cursor U/ D/ L/ P], then press
[ENTER].
Note
• You cannot select the same title twice and combine
it into a single title.
• If either one of the two original titles is deleted, the
combined new title is also deleted.
Playlist
3
2
1
Adding titles to a Playlist
Playlist
VR
DVD-RW
You can add a title to the playlist as you wish.
You can add up to 99 titles to a Playlist (as long as the
total number of the playlist does not exceed 999
chapters).
Add New
Title
Delete
Playlist
Press [DVD ] first.
3 Select “Yes” using [Cursor L/ P],
then press [ENTER].
1 Follow steps 1 to 3 in
“Playlist Deleting titles.”
The Playlist is deleted.
4 Press [SETUP].
2 Select “Add New Title” using
[Cursor U/ D/ L/ P], then press
[ENTER].
Writing on the disc starts.
It may take a while to write the data on a disc.
Note
Playlist
• Deleting a Playlist will not increase the available
recording time on the disc.
• When the disc contains 99 titles or more, or 999
chapters or more, "Add New Title" cannot be
selected.
3
2
1
Add New
Title
Delete
Playlist
3 Select the desired title using
[Cursor U/ D/ L/ P], then press
[ENTER].
4 Press [SETUP].
Writing on the disc starts.
It may take a while to write the data on a disc.
Hint
• To delete a title from the Playlist, refer to “Deleting
titles” on page 53.
• To delete the Playlist, refer to “Deleting a Playlist” on
this page.
Playlist Deleting a Playlist
VR
DVD-RW
A Playlist can be deleted if it is no longer needed.
Press [DVD ] first.
1 Follow steps 1 to 3 in
“Playlist Deleting titles.”
EN
56
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 57 Thursday, March 31, 2005 10:04 PM
Changing the Setting menu
Tour of the Setting menu
The following table shows the items you can set and their default settings.
Use the table as a reference for efficient operation.
Setting menu
Menu items
Default
Function
Language setting
page 58
Disc Menu Language
English
Sets the disc menu language.
Sets the audio language.
Sets the subtitle language.
Audio Language
Subtitle Language
FL Dimmer
Original
OFF
Display setting
page 59
Bright
Sets the front display
brightness.
Screen Saver
Digital Out
10 minutes
48 kHz
Sets the idling time before the screen
saver starts.
Audio Setting
pages 59-60
PCM
Sets whether sound recorded
at 96 kHz is down sampled to
48 kHz or not.
Dolby Digital Stream
Sets the digital audio output
signal specification.
MPEG
DTS
PCM
OFF
ON
Sets the digital audio output
signal specification.
Sets whether DTS signal is
output or not.
Dynamic Range Control
Fast Forward with Audio
Compresses the sound volume
range.
OFF
All
Outputs sound during fast
forward play back.
Parental setting
page 61
Parental Lock
• Change password
Video Out
Sets the DVD parental control level.
Sets and change the password.
Sets the TV system.
Output setting
page 62
TV System
PAL
Note
• Changes you make to the Setting menu remain even after power to the unit is switched off or the disc tray is
opened or closed.
• [SETUP] will not function when the unit is turned on by pressing [STANDBY-ON] during either the DVD or VCR
timer-standby mode.
57
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 58 Thursday, March 31, 2005 10:04 PM
If “Other” is selected, enter the
appropriate 4-digit code using
[the Number buttons].
Language setting
Refer to the language code table on page 70.
1 In stop mode, press [SETUP].
DVD
Disc Menu Language
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
Code Input
4
7
4
If it has already appeared, proceed to step 3.
3 Select “Playback” using
[Cursor U/ D], then press [ENTER].
When you finish entering the code,
press [ENTER].
4 Select the desired item using
[Cursor U/ D], then press [ENTER].
5 Press [SETUP] to exit.
Hint
Disc Menu Language (Default: English)
Set the Disc Menu language.
• You can also change or switch off the subtitles on a
DVD from the disc menu if it is available.
• Press [CLEAR] or [Cursor L] to erase numbers
entered incorrectly.
Playback
DVD
DVD
Disc Menu Language
TV Aspect
Parental Lock
4:3 Letter Box
All
English
French
Disc Menu Language
English
Spanish
Audio Language
Subtitle Language
Digital Out
Original
OFF
German
Italian
Note
Swedish
Dutch
Dynamic Range Control
Fast Forward with Audio
Video Out
ON
OFF
• You can only select the languages supported by the
inserted disc.
Other
• The Audio Language setting may not be available for
some discs.
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
Audio Language (Default: Original)
Set the Audio language.
Playback
TV Aspect
DVD
DVD
Audio Language
4:3 Letter Box
All
Original
English
French
Parental Lock
Disc Menu Language
English
Audio Language
Audio Language
Original
Original
Spanish
Spanish
Subtitle Language
Digital Out
OFF
German
Italian
Dynamic Range Control
Fast Forward with Audio
Video Out
ON
Swedish
Dutch
OFF
Other
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
If Original is selected, the audio language is the
default of the inserted disc.
Subtitle Language (Default: OFF)
Set the Subtitle language.
Playback
TV Aspect
DVD
Subtitle Language
DVD
4:3 Letter Box
All
O
OFF
Parental Lock
English
French
Spanish
German
Italian
Disc Menu Language
Audio Language
English
Original
Sutte aguae
Subtitle Language
OF
OFF
Digital Out
Dynamic Range Control
Fast Forward with Audio
Video Out
ON
Swedish
Dutch
OFF
Other
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
EN
58
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 59 Thursday, March 31, 2005 10:04 PM
Display setting
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
Audio setting
Choose the appropriate Audio settings for your audio
equipment.
This will only affect DVDs playback.
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3 Select “Display” using
[Cursor U/ D], then press [ENTER].
If it has already appeared, proceed to step 3.
4 Select the desired item using
3 Select “Playback” using
[Cursor U/ D], then press [ENTER].
[Cursor U/ D], then press [ENTER].
FL Dimmer (Default: Bright)
Set the front panel display brightness.
4 Select the desired item using
[Cursor U/ D], then press [ENTER].
Display
VCR DVD
FL Dimmer
Auto
VCR DVD
Note
FL Dimmer
FL Dimmer
Brgh
Bright
Brh
Bright
Screen Saver
10 minutes
• The Dynamic Range Control function is available
only on discs recorded in the Dolby Digital format.
Dark
Digital Out
Set the digital audio output.
Select a setting using
[Cursor U/ D], then press [ENTER].
You can choose one from “Auto”, “Bright” and
“Dark.”
If “Auto” is selected, the display gets dark when
the power is OFF.
Playback
TV Aspect
DVD
Digital Out
DVD
4:3 Letter Box
All
P
PCM
48kHz
Parental Lock
Dolby Digital
MPEG
Stream
PCM
Disc Menu Language
Audio Language
Subtitle Language
English
Original
OFF
DTS
OFF
Digital Out
Digital Out
Dynamic Range Control
Fast Forward with Audio
Video Out
ON
OFF
Screen Saver (Default: 10 minutes)
Select a setting using
Set the screen saver time delay.
[Cursor U/ D], then press [ENTER].
Proceed with either of the following steps.
Display
VCR DVD
Screen Saver
DVD
FL Dimmer
Bright
OFF
Screen Saver
5minutes
10 minutes
10 minutes
10 minutes
PCM sampling (Default: 48 kHz)
15 minutes
30 minutes
DVD
Digital Out - PCM
48kHz
96kHz
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
5 Press [SETUP] to exit.
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
48 kHz: If your amplifier / decoder is NOT compatible
with 96 kHz PCM, select “48 kHz.” Sound
recorded at 96 kHz is down sampled to 48
kHz.
96 kHz: If your amplifier / decoder is compatible with
96 kHz PCM, select “96 kHz.” Sound is
sampled at 96 kHz.
59
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 60 Thursday, March 31, 2005 10:04 PM
Note
Settings for DTS (Default: OFF)
When playing back disc with copyright protection:
• Even if you select “96 kHz,” the sound is down
sampled to 48 kHz.
DVD
Digital Out - DTS
ON
Dolby Digital conversion (Default: Stream)
OFF
Digital Out - Dolby Digital
DVD
PCM
Stream
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
Select a setting using
[Cursor U/ D], then press [ENTER].
ON: Outputs DTS signals.
If your amplifier / decoder is compatible with
DTS, set to “ON.”
OFF: No DTS signal is output.
If your amplifier / decoder is NOT compatible
with DTS, set to “OFF.”
Your setting is activated.
PCM: Converts the Dolby Digital into PCM
(2 channel).
If your amplifier / decoder is NOT compatible
with Dolby Digital, set to “PCM”.
Stream: Outputs Dolby Digital signals.
If your amplifier / decoder is compatible with
Dolby Digital, set to “Stream”.
Dynamic Range Control (Default: ON)
Set to "ON" to make the dynamic range narrower.
Playback
TV Aspect
DVD
DVD
4:3 Letter Box
All
Parental Lock
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
Hint
When playing back a DVD-RW disc recorded in VR
mode:
Dynamic Range Control
Dynamic Range Control
ON
ON
Fast Forward with Audio
OFF
• If the audio source on a disc is in Dolby Digital
format, set “Dolby Digital” to “PCM” so that you can
switch to main audio (L), sub audio (R), or a
combination of both (L / R) using your amplifier /
decoder.
Video Out
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
The Dynamic Range Control function is effective
only with analogue audio connection.
Settings for MPEG (Default: PCM)
Digital Out - MPEG
DVD
Fast Forward with Audio (Default: OFF)
PCM
Set to “ON” to output the sound during DVD playback
at x1.5 fast forward.
Stream
DVD
Playback
TV Aspect
Fast Forward with Audio
DVD
4:3 Letter Box
All
ON
Parental Lock
OFF
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
Dynamic Range Control
ON
Fast Forward with Audio
Fast Forward with Audio
OFF
OFF
Select a setting using
Video Out
[Cursor U/ D], then press [ENTER].
Your setting is activated.
Select a setting using
[Cursor U/ D], then press [ENTER].
Your setting is activated.
PCM: Converts MPEG into PCM.
If your amplifier / decoder is NOT compatible
with MPEG, set to “PCM.”
Stream: Outputs MPEG Audio signals.
If your amplifier / decoder is compatible with
MPEG, set to “Stream.”
5 Press [SETUP] to exit.
EN
60
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 61 Thursday, March 31, 2005 10:04 PM
Parental level
All: All parental locks are cancelled.
8: DVD software of any grade (adult / general /
children) can be played back.
7 to 2: Only DVD software intended for general
use and children can be played back.
1: Only DVD softwares intended for children can
be played back.
DVD-Videos Parental lock level
Some DVD-Videos feature a Parental Lock function.
If the rating of the inserted disc exceeds the level you
set, playback will stop. You must enter a password
before the disc will be played back. This feature
prevents your children from viewing inappropriate
material.
A password is not yet set
Select “Yes” using [Cursor U/ D],
then enter a new password using
[the Number buttons], then press
[ENTER].
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
Your setting is activated.
If it has already appeared, proceed to step 3.
If you select “No”, proceed to Step 5.
3 Select “Playback” using
A password is already set
[Cursor U/ D], then press [ENTER].
Enter the current password using
[the Number buttons].
4 Select “Parental Lock” using
[Cursor U/ D], then press [ENTER].
DVD
Parental Lock
DVD
Playback
TV Aspect
4:3 Letter Box
Parental Lock
All
Password Input
Disc Menu Language
Audio Language
Subtitle Language
Digital Out
English
Original
OFF
Dynamic Range Control
Fast Forward with Audio
Video Out
ON
OFF
Change the password
Note
DVD
Parental Lock
• The parental lock function may not be available on
some discs.
• It may be difficult to determine if some DVDs
support the parental lock function. Be sure to
confirm that the parental lock function operates in
the way that you have set.
Change Password?
Yes
No
• Record the password in case you forget it.
Parental Lock (Default: All)
Set the Parental Lock level.
Select “Yes” using [Cursor U/ D],
then enter a new password using
[the Number buttons], then press
[ENTER].
Change the Parental Lock level using
[Cursor U/ D], then press [ENTER].
Proceed with either of the following steps.
Your setting is activated.
Parental Lock
DVD
If you press [ENTER] without entering a
password, you can set up without a password.
All
8
7
6
5
4
3
2
1
5 Press [SETUP] to exit.
Note
• Press [CLEAR] to erase numbers entered
incorrectly.
• If you forget your password or you want to clear all
settings in Parental lock, enter [4], [7], [3], [7] using
[the Number buttons] at the option window. Your
password is cleared and parental levels are set to
“All.”
61
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 62 Thursday, March 31, 2005 10:04 PM
Changing Video Out system
Setting TV system
1 In stop mode, press [SETUP].
2 Select “Advanced Setting Menu”
using [Cursor U/ D], then press
[ENTER].
If it has already appeared, proceed to step 3.
3 Select “Playback” using
[Cursor U/ D], then press [ENTER].
4 Select “Video Out” using
[Cursor U/ D], then press [ENTER].
5 Press [ENTER].
6 Select the desired system setting
using [Cursor U/ D], then press
[ENTER].
DVD
Video Out - TV System
PAL
Auto
PAL: Outputs a modified PAL signal for viewing
discs recorded with the NTSC system on a
PAL system TV.
Auto: Changes the video system (PAL / NTSC)
automatically according to the format of
the inserted disc.
7 Press [SETUP] to exit.
Note
• With discs recorded using the PAL system, a PAL
signal is output for viewing on a PAL system TV.
• Discs recorded with the PAL system cannot be
viewed on an NTSC system TV.
• With discs recorded using the NTSC system, an
NTSC signal is output for viewing on an NTSC or
Multi system TV.
• With discs recorded using the NTSC system, select
PAL to view on a PAL system TV.
EN
62
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 63 Thursday, March 31, 2005 10:04 PM
VCR functions
Playback
Recording and one-touch timer
recording (OTR)
VCR
1 Press [STANDBY-ON] to turn on the
Basic Recording
unit.
VCR
To play back a tape, turn on the TV and be sure to
select the input to which the unit is connected.
Before recording, make sure:
• The desired channel is selected by pressing the
number buttons on the remote control.
• There is a tape with a record tab in the unit.
• The desired recording speed is selected in SP
(standard play) or LP (long play) mode by pressing
[REC SPEED] on the remote control.
2 Press [VCR
3 Insert a prerecorded tape, then press
[PLAY P] to begin playback.
].
4 During playback, press [PAUSE p].
Playback will be paused and sound will be muted.
5 Press [PLAY P] to resume playback.
6 Press [STOP S] to stop playback.
Tape speed
Recording / Playback Time
Type of tape
SP mode
E60
1 hour
2 hours
E120
2 hours
4 hours
E180
3 hours
6 hours
7 Press [STOP / EJECT SO] on the
LP mode
unit to eject the tape.
• Refer to page 28 for instructions on timer recording.
Note
• When a tape without record tab is inserted, the unit
will start playback automatically.
• Tracking will be automatically adjusted upon
playback. To adjust the tracking manually, press
[PROG. U/ D].
1 Turn on the unit and insert a
recordable tape.
Make sure that the TV input is set on the unit.
2 Press [VCR
].
3 Select the recording speed using
[REC SPEED].
• The desired recording speed is selected in SP
(standard play) or LP (long play) mode by
pressing [REC SPEED].
4 Select the desired channel to record
using [PROG. U/ D] or
[the Number buttons].
5 Press [REC / OTR] to start recording.
To temporarily stop recording or to resume it,
press [PAUSE p]. After the unit has been in
pause mode for 5 minutes, it will stop
automatically to protect the tape and the video
head from damage.
6 Press [STOP S] when the recording
is completed.
63
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 64 Thursday, March 31, 2005 10:04 PM
Accidental erasure prevention
To prevent accidental recording on a recorded
cassette, remove its record tab. To record on it later,
cover the hole with cellophane tape.
Search
Index search
VCR
Record tab
1 Press [VCR
2 During tape playback, press
[SEARCH] so that the index search
menu appears.
].
One-touch timer recording
VCR
This feature allows you to set the recording length
simply by pressing [REC / OTR].
3 Enter the number of recordings you
1 Turn on the unit and insert a
recordable tape.
wish to skip using
[the Number buttons] within 30
seconds.
Make sure that the TV input is set on the unit.
2 Press [VCR
].
4 Press [f] or [r] to start index
3 Select the recording speed using
search.
[REC SPEED] (See page 63.).
If you want to go in the forward direction, press
[f].
4 Select the desired channel to record
using [PROG. U/ D] or [the Number
buttons].
If you want to go in the reverse direction, press
[r].
After index search, the VCR will play back the
tape automatically.
5 Press [REC / OTR] repeatedly until
the desired recording time (30
minutes to 8 hours) appears on the
TV screen.
Note
• Every time a tape is recorded, an index mark is
written on the tape.
One-touch timer recording will start.
Time search
0:30
VCR
(Normal Recording)1:00
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
8:00
7:30
1 Press [VCR
2 During tape playback, press
[SEARCH] repeatedly so that the
Time search menu appears.
].
• When the unit reaches the specified time, it will be
turned off automatically.
• To change the recording length during one-touch
timer recording, press [REC / OTR] repeatedly until
the desired length appears.
• To cancel one-touch timer recording within the
specified time, press [STOP S].
3 Enter your desired time to skip using
[the Number buttons] within 30
seconds.
Hint
• The remaining recording time will appear on the TV
screen during one-touch timer recording. Press
[DISPLAY] to see it on the TV screen.
4 Press [f] or [r] to start time
search.
If you want to go in the forward direction, press
[f].
Note
If you want to go in the reverse direction, press
[r].
After time search, the unit will play back the tape
automatically.
• If VCR one-touch timer recording is completed
during DVD playback or recording, the VCR will be
in stop mode and the DVD keeps the current mode.
• You cannot use the pause function during one-touch
timer recording.
• When one-touch timer recording is finished and the
power is turned off, the unit will switch to the timer-
standby mode automatically if a timer recording has
been programmed. Press [T-SET] to cancel the
timer-standby mode to use the unit continuously.
Note
• These functions are not available during recording.
• Press [STOP S] to stop the search.
• If the tape reaches the end during a Search, this unit
will cancel the search and rewind the tape.
EN
64
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 65 Thursday, March 31, 2005 10:04 PM
Other operations
Hi-Fi Stereo Sound System
This unit will record and playback Hi-Fi stereo sound.
This unit will receive stereo and bilingual broadcasts
and it is possible to record in several ways and to play
back the sound.
VCR
Press [VCR] first.
To cue or review picture during playback (Picture
Search):
Selecting the Sound Mode
Press [FWD f] or [REW r] during playback.
Press it again and the unit will search in super high
speed.
You can select each mode by pressing [AUDIO] on
the remote control. Each mode is indicated on the TV
screen as following.
To freeze the picture on TV screen during
playback (Still mode):
• During reception of bilingual broadcasts
Press [PAUSE p]. Each time you press the button,
the picture will be forwarded frame by frame.
If the picture begins to vibrate vertically during the still
mode, stabilize the picture by pressing the
[PROG. U/ D].
Display on
the TV screen
Mode
Audio output
Main
Main audio from the both
speakers
Main
If the picture is distorted or rolling vertically, adjust the
vertical hold control on your TV, if equipped.
Sub
Sub audio from the both
speakers
Sub
Counter Reset:
Press [CLEAR].
Main /
Sub
• Main audio from the left
speaker
Main
Sub
• Sub audio from the right
speaker
To play back in slow motion:
Press [SLOW] during playback or the still mode.
If the noise bars appear on the TV screen, you can
reduce it by pressing [PROG. U/ D].
Note
Note
• If you play back non-Hi-Fi tapes, the unit will play
back automatically in monaural even if you select
any mode.
• If the stereo signal becomes weak, the broadcast is
automatically recorded in monaural.
• Still / Slow / Pause mode will be automatically
cancelled after 5 minutes to prevent damage to the
tape and the video head.
• To return to play back from the Picture Search / Still /
Slow mode, press [PLAY P].
65
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 66 Thursday, March 31, 2005 10:04 PM
Others
Troubleshooting
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment by you may eliminate the problem and restore correct operation.
DVD • VCR
Symptom
Remedy
The power does not turn on.
• Check the mains cable is connected securely.
• Check building circuit the breaker (In case of power failure) .
There is no picture.
• Check signal cables are connected securely.
• Check if a connecting cable is damaged.
• Check connections to your TV. (See page 16.)
• Switch the input selector on your TV (to “AV1,” for example) until a picture
appears on the screen.
TV programme picture does not fill the
screen.
• Set channels with “Auto Tuning” from the screen menu. (See page 18.)
• Select the channel of a TV program using [PROG. U/ D].
TV programme pictures are distorted.
• Adjust the direction of the TV antenna.
• Adjust the picture (see the TV instruction manual).
• Place the antenna and the TV farther apart.
• Separate any bunched antenna cables and the TV.
TV channel cannot be changed.
• Switch the TV input.
• Check if the antenna cable is connected correctly. (See page 16.)
The channel cannot be changed from the
channel you are recording.
• Set the TV input to “TV.”
Playback picture is distorted.
• Do not bring equipment that may cause electrical interference, such as a
cellular phone, near the unit.
The playback picture or TV programme from
equipment connected through the unit is
distorted.
• If a DVD player, VCR or tuner is connected to your TV via the unit, the copy-
protection signal applied to some programs could affect picture quality.
Disconnect the playback equipment in question and connect it directly to your
TV.
Nothing was recorded even though you set
the timer setting correctly.
• There was a power failure during recording.
• The unit’s internal clock stopped due to a power failure that lasted for more
than 30 seconds.
• Reset the clock. (See page 20.)
• Unplug the mains cable from the AC outlet and plug it in again.
• The programme contains copy protection signals that restrict copying.
• The timer setting overlapped with another setting that was set later or has
priority.
Timer recording is not complete or did not
start from the beginning.
• The timer setting overlapped with another setting that was set later or has
priority. (See page 30.)
• There was not enough disc space.
There is no sound.
• The disc is dirty or flawed.
• Check if all cables are connected securely.
• Check if a connecting cable is damaged.
• Check the connections to the amplifier input.
• Check if the input source setting on the amplifier is correct.
• Check if the recorder is in Pause mode or in Slow-motion Playback mode.
• Check if the recorder is in Fast Forward or Fast Reverse mode.
Timer recording is not possible.
• Make sure
press [T-SET].
indicator appears on the front panel display of this unit. If not,
The remote control does not function.
• Batteries are exhausted.
• There are obstacles between the remote control and the unit.
• The remote control is too far from the unit.
• There are no batteries in the remote control.
• The unit is not turned on.
• The remote control is not pointed at the remote sensor on the unit.
• Press [DVD
] or [VCR
], whichever you need. Then, try again.
• If the above remedies do not solve the problem, please call the Service Centre
for help.
The unit does not operate correctly.
• If static electricity or anything else causes the unit to operate abnormally,
unplug the mains cable and plug it in again.
EN
66
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 67 Thursday, March 31, 2005 10:04 PM
DVD
Symptom
Remedy
There is no picture.
• If the setting menu display appears, press [SETUP] or [RETURNR] to turn
off the display.
Picture noise appears.
• The disc is dirty or flawed.
• If the unit is connected to your TV via a VCR, or if it is connected to a
combination TV / VIDEO player, the copy-protection signal applied to some
DVD programs could affect picture quality. If you still experience this problem
even when you connect the unit directly to your TV, try connecting the unit to
your TV’s S-VIDEO input.
Sound is noisy.
• The disc is dirty or flawed.
The unit does not play back the disc.
• No disc is inserted.
• A blank disc is inserted.
• No cassetetape is inserted.
• The disc is upside down. Insert the disc with the labeled side facing up.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM). (See page 36.)
• The region codes on the DVD-Video and the unit are not matched. (See page
36.)
• Moisture has condensed inside the unit. Remove the disc and leave the unit
turned on for about two hours until the moisture evaporates. (See page 3.)
• The unit cannot play back the disc if it was recorded on another recorder and
not finalised. (See page 34)
There is no sound.
• If the audio signal is not output from the DIGITAL OUT (OPTICAL (DRV-B2737
only), COAXIAL) jack, check the Audio setting (See page 59).
Playback image freezes for a moment.
• During the playback of a two layered disc, the picture may freeze for a moment
while playback switches from the first to the second layer. This is not a
malfunction.
The unit does not play back the disc from the
beginning.
• Resume playback is activated. (See page 41.) Press [STOP S] twice.
• You have inserted a disc whose title menu or DVD menu automatically appears
on the TV screen when it is first inserted.
The unit starts playing back the disc
automatically.
• The DVD-Video features an auto playback function.
Some functions such as Stop, Search, or
Slow-motion Playback cannot be performed.
• Depending on the disc, you may not be able to perform some of those
operations. See the instruction manual supplied with the disc.
The language for the sound track cannot be
changed.
• Multilingual tracks are not recorded on the DVD-Video, DVD-R, or DVD-RW
being played back.
• The DVD-Video prohibits the changing of the language for the sound track.
• Try changing the language using the DVD-Video menu.
The subtitle language cannot be changed or
turned off.
• Multilingual subtitles are not recorded on the DVD-Video.
• The DVD-Video prohibits changing the subtitles.
• Try changing the subtitles using the DVD-Video menu.
Angles cannot be changed.
• Multi-angles are not recorded on the DVD-Video being played back.
• You can change the angle only if the disc contains multi-angle scene. Angles
can be changed only when the multi-angle scene appears on the screen.
• The DVD-Video prohibits changing angles.
• Try changing the angle using the DVD-Video menu.
Recording does not start immediately after
pressing [REC / OTR].
• An unused DVD-R or DVD-RW was inserted. It takes a while for the unit to
automatically format a DVD-RW.
• Make sure the tape has a record tab when you record to a cassette tape. If
needed, cover the hole with cellophane tape.
Recording does not stop immediately after
you press [STOP S].
• It will take a few seconds for the unit to send data to disc before recording can
stop.
The disc tray does not open when you press
[OPEN / CLOSE / EJECT O].
• It may take a few seconds for the disc tray to open after you have recorded or
edited a disc.
• This is because the unit is sending data to the disc.
“Repairing” appears on the display.
• If a power failure occurs or the mains cable is unplugged during recording,
finalising, formatting or editing (even after "Wait for moment." message
disappeared), a repairing process will begin automatically when the unit is
turned on next time.It may take several minutes up to about four hours.
67
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 68 Thursday, March 31, 2005 10:04 PM
VCR
Symptom
Remedy
Picture noise appears.
• Adjust tracking control for better picture by pressing [PROG. U/ D] while you
are playing back a video tape.
• Head cleaning for VCR may be necessary.
Refer to “AUTO HEAD CLEANING”.
The unit does not play back the tape.
• No video tape is inserted.
Recording does not start immediately after
pressing [REC / OTR].
• Make sure the video tape has a record tab when you record to a video tape. If
needed, cover the hole with cellophane tape.
The remote control does not function.
• Check if a video tape is in the unit. Press [VCR
]. Then, try again.
The motor rotates even when playback /
recording is stopped.
• The motor may rotate for the duration of approximately 5 minutes for efficient
operation. This is not a malfunction.
EN
68
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 69 Thursday, March 31, 2005 10:04 PM
Error message
Cause
Solution
Disc Error
• An unplayable disc is inserted in the unit.
• The disc is upside down.
• Insert a standard disc shown in “Playable
discs.” (See page 36.)
• Insert the disc with the labeled side facing
up.
— Please eject the disc. —
Playback feature may not be
available on this Disc.
Region Error
• Playback is not authorized in the region of
the DVD-Video that you inserted in the
unit.
• Insert a DVD-Video with region codes 2 or
ALL.
— Please eject the disc. —
Playback is not authorized in
your region.
Parental Lock On
The current selected parental
level prohibits playback.
• The current selected parental level in the
setting menu prohibits playback.
• Check the “Parental Lock” setting. (See
page 61.)
Recording Error
This programme is not allowed to
• The recording function encountered a
copy prohibited programme.
• You cannot record copy prohibited
programmes.
be recorded.
• Original source is in NTSC system.
Recording Error
This programme is not
recordable in Video mode.
• You are trying to record a copy-once
programme onto a DVD-RW disc in Video
mode.
• Set “DVD-RW Recording Format” to “VR
mode.” (See page 24.)
Recording Error
Cannot record on this disc.
• You are trying to record onto a disc that is
unrecordable, or the disc status does not
satisfy recording requirements.
• The disc is dirty.
• Insert a recordable disc, and ensure the
disc status satisfies the recording
requirements. (See page 22.)
• Clean the disc with a cleaning cloth.
• Replace the disc.
• The disc is damaged.
Recording Error
This programme is not allowed to
be recorded on this disc.
• You are trying to record a copy-once
programme onto a DVD-RW disc that is
not compatible with CPRM.
• Insert a ver. 1.1 or ver. 1.2 DVD-RW disc
(compatible with CPRM.)
Recording Error
This disc is protected and not
recordable.
• You are trying to record onto a disc that is
set as protected in the Disc Setting Menu.
• Remove the disc protect setting in the Disc
Setting menu. (See page 34.)
Recording Error
Disc is full.
• You are trying to record onto a disc that
has no space for recording.
• Insert a recordable disc with enough
recording space.
(No area for new recording)
Recording Error
You cannot record more than 99
titles on one disc.
• You are trying to record onto a disc on
which the number of recorded titles has
reached the maximum (99).
• Delete unnecessary titles. (See page 51.)
(The maximum is 99.)
Recording Error
• You are trying to record onto a disc on
which the number of recorded chapters
has reached the maximum (999).
• This unit cannot delete the original
chapter. Delete unnecessary chapter
marker on other DVD recorders.
• Delete unnecessary titles from an original
list. (See page 51.)
You cannot record more than
999 chapters on one disc.
(The maximum is 999.)
Recording Error
You cannot record on this disc as
Control Information is full.
• This disc has no space to write Control
Information when recording or deleting
contents.
• Delete unnecessary titles. (See page 51.)
• When editing has been repeatedly
performed, the control information area
may become full even though the
recording area has enough space.
Recording Error
You cannot record on this disc as
Power Calibration Area is full.
• When recordings are performed
repeatedly onto an unstable disc, this area
may become full.
• Insert a new disc.
• Every time you insert a disc for recording,
part of the disc's working area will be
used.
• If you repeat this frequently, it will be used
up quicker and you may not be able to
record full 99 titles.
Recording Error
This disc is already finalised.
• You are trying to record onto a disc that is
already finalised.
• Release the finalising for the disc. (See
page 34.)
* If you are still having trouble with the unit after checking all the Troubleshooting points, write down the error code
and the error description and consult your dealer or an authorized service centre.
69
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 70 Thursday, March 31, 2005 10:04 PM
Language code
Language
(Afan) Oromo
Abkhazian
Afar
Code
6159
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
Language
Code
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
Language
Code
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
Language
Code
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Finnish
Lingala
Sindhi
French
Lithuanian
Macedonian
Malagasy
Malay
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Frisian
Afrikaans
Albanian
Amharic
Arabic
Galician
Georgian
German
Greek
Malayalam
Maltese
Armenian
Assamese
Aymara
Greenlandic
Guarani
Gujarati
Hausa
Maori
Marathi
Moldavian
Mongolian
Nauru
Azerbaijani
Bashkir
Hebrew
Hindi
Basque
Nepali
Tamil
Bengali;Bangla
Bhutani
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Norwegian
Occitan
Tatar
Telugu
Thai
Bihari
Oriya
Bislama
Breton
Panjabi
Tibetan
Tigrinya
Tonga
Pashto; Pushto
Persian
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Irish
Polish
Tsonga
Turkish
Turkmen
Twi
Italian
Portuguese
Quechua
Rhaeto-Romance
Romanian
Russian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Chinese
Corsican
Croatian
Czech
Ukrainian
Urdu
Samoan
Sangho
Uzbek
Kinyarwanda
Kirghiz
Vietnamese
Volapuk
Welsh
Danish
Sanskrit
Dutch
Kirundi
Scots Gaelic
Serbian
English
Korean
Wolof
Esperanto
Estonian
Faroese
Fiji
Kurdish
Serbo-Croatian
Sesotho
Xhosa
Laothian
Latin
Yiddish
Yoruba
Zulu
Setswana
Shona
Latvian; Lettish
EN
70
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 71 Thursday, March 31, 2005 10:04 PM
Glossary
Analogue audio
Dolby Digital
Playlist
An electrical signal that directly
represents sound. In contrast,
digital audio can also be an
electrical signal, but is an indirect
representation of sound. See also
Digital audio.
A system developed by Dolby
Laboratories that compresses
digital sound. It works with stereo
(2ch) or multi-channel audio.
From this list you can play back
contents of a disc in your desired
order or in sequence. It is also
possible to directly search for a
specific scene.
DTS
(Digital Theater System)
Region code
Aspect ratio
DTS is a Multi-channel surround
Regions associate discs and
The width of a TV screen relative to
sound system, but it is different from players with particular areas of the
its height. Conventional TVs are 4:3 Dolby Digital. Both formats were
world. This unit will only play back
discs that have compatible region
codes. You can find the region code
of your unit by looking on the rear
panel. Some discs are compatible
with more than one region (or all
regions).
(i.e., the screen is almost square).
widescreen models are 16:9 (the
screen is almost twice as wide as its
height).
developed by Digital Theater
System, Inc.
Finalise
To make DVDs that have been
recorded playable in DVD players. It
is possible to finalise DVD-R / DVD-
RW discs with this unit.
Chapter
Just as a book is split up into
several chapters, a title on a DVD
disc is usually divided into chapters.
See also Title.
Sampling frequency
The rate at which sound is
JPEG
measured by a specified interval to
turn it into digital audio data. The
number of samples in one second is
defined as the sampling frequency.
The higher the rate is, the better the
possible sound quality.
(Joint Photographic Experts
Group)
CM SKIP
This unit can skip TV commercials
during DVD Video playback. Once
[CM SKIP] is pressed, the start
point will be set forward 30 seconds
and playback resume automatically.
(You can press [CM SKIP] up to 6
times.)
JPEG is a method of compressing
still image files. You can copy JPEG
files on CD-RW / R discs from a
computer and play back the files on
this unit.
S-Video output
Video is output as the individual
signals of colour(C) and
MP3
(MPEG Audio Layer 3)
luminance(Y), so a higher-quality
picture will be displayed.
CPRM
(Content Protection for
Recordable Media)
MP3 is a method of compressing
files. You can copy MP3 files on CD-
RW / R discs from a computer and
play back the files on this unit.
Title
CPRM is a scrambling copy
protection system for the protection
of “copy-once” broadcast
programmes (e.g. some satellite
broadcasts).
(DVD)
A collection of chapters on a DVD.
See also chapter.
PBC (Video CD only)
(Playback Control)
(Video CD)
This function enables you to play
back interactive software using a
menu screen. See also Title.
The contents of a Video CD. When
playing back a Video CD with the
PBC function, the title menu will
appear automatically.
Digital audio
An indirect representation of sound
using numbers. During recording,
the sound is measured at discrete
intervals (44 or 100 times a second
for CD audio) by an analogue-to-
digital converter, generating a
stream of numbers. On playback, a
digital-to-analogue converter
generates an analogue signal
based on these numbers. See also
Sampling frequency and Analogue
audio.
PCM
(Pulse Code Modulation)
Track
PCM is a format that converts audio
into digital data. It is mainly used for
Audio CDs and DAT. This unit can
play back sounds as realistic as
possible by converting even
Audio CDs and Video CDs use
tracks to divide the contents of a
disc. The DVD equivalent is called a
chapter. See also Chapter.
compressed Dolby Digital and
MPEG audio to PCM.
71
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 72 Thursday, March 31, 2005 10:04 PM
Specifications
General
System
DVD-Video, DVD-RW / R, DVD+RW / R, CD-DA, CD-RW / R,
Video Cassette Tape
VCR video heads
Power requirements
Power consumption
Weight
Four heads
220–240 V
10%, 50 Hz 0.5%
35 W (standby: 5.0 W)
4.3 kg
Dimensions (width x height x depth)
Operating temperature
Operating humidity
TV format
435 x 100 x 261 mm
5°C to 40°C
5% to 85% (no condensation)
PAL - I
Recording
Recording format
Video Recording format (DVD-RW only),
Video format (DVD-RW, DVD-R)
Recordable discs
DVD-ReWritable, DVD-Recordable
Video recording format
Sampling frequency
Compression format
13.5 MHz
MPEG
Audio recording format
Sampling frequency
Compression format
48 kHz
Dolby Digital
Tuner
Receivable channels
IRA - E69
Note
• The specifications and design of this product are subject to change without notice.
EN
72
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 73 Thursday, March 31, 2005 10:04 PM
73
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 74 Thursday, March 31, 2005 10:04 PM
EN
74
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 75 Thursday, March 31, 2005 10:04 PM
75
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DRV_B2737_B2734.book Page 76 Thursday, March 31, 2005 10:04 PM
Declaration of Conformity
This product complies with the requirement of the directives
EMC-Directive:
Low Voltage Directive:
CE Marking:
89 / 336 / EEC
73 / 23 / EEC
93 / 68 / EEC
We declare that the following product:
DVD Recorder with Video Cassette Recorder, Models DRV-B2737/DRV-B2734
are in compliance with following Regulations.
EN55013: 2001+A1:2003, EN55020: 2002+A1:2003,
EN61000-3-2: 2000, EN61000-3-3: 1995 + A1: 2001
EN60065: 1998
EN60825-1 Edition 1.2: 2001
Questions and Help on this products, please call
Help Line: 0870 3833010 in UK.
© 2004-2005 FUNAI EUROPE GMBH. All rights reserved.
1VMN20789 / E9705BD / E9701BD ★★★★★
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
|