FMI Indoor Fireplace W32DS User Manual

WS26DS, W32DS and W36DS  
Wall Mantel and Base with Trim  
ASSEMBLY AND INSTALLATION INSTRUCTIONS  
Important: Read entire instruction sheet before  
assembling or installing mantel kit.  
Note: Gather all mantel pieces together before assembling  
mantel.  
these mantels are only approved for use with any  
DESA Heating Products compact fireplace system.  
Do not use mantel with any other product.  
WARNING: Only use 1 1/4" screws in pocket holes to  
assemble mantel. Damage to mantel will result if other  
screws are used for this purpose.  
This mantel kit contains the following:  
• Mantel pieces - unassembled and marked as follows:  
WARNING: Use only 1/2" or 3/4" screws with brack-  
ets in hardware pack 118983-01. Damage to mantel will  
result if other screws are used for this purpose.  
Base #1  
Left Side #4 with arrow  
Right Side #2 with arrow  
Left Front Leg #5 with arrow  
Right Front Leg #3 with arrowHeader #6 with arrow  
Top #7  
AssemblING mANtel  
• Hardware Package (117197-01)  
• Bracket Hardware Kit (118983-01)  
• Trim Kit 113140-02 (26"), 113140-01 (32") or  
113140-14 (36")  
• Trim Kit Hardware (102866-01)  
The hardware kit 117197-01 contains the following:  
• 28 - 1 14" Screws  
ImPORtANt: more than one person is required to lift  
assembledmantel.liftmantelbylegassemblies.lifting  
by header or mantel top could damage mantel.  
1. For leg assembly, lay side or front that does not contain  
pocket holes front side down on a soft surface. Pocket  
hole locations will vary by model. Pay special attention  
to the up direction arrows on panels.  
• 2 - 3" Screws  
Tools required:  
2. Position second panel as shown in Figure 1, page 2.Align  
panels at bottom. With one person holding the panel align-  
ment secure, attach panels using 1 1/4" screws through  
pocket holes. Check assembly for correct alignment.  
3. Repeat steps 1 and 2 for second leg assembly.  
4. Each leg assembly will use 3 brackets for stability. Your  
bracket hardware kit will contain either 1/2" or 3/4" screws.  
Using two 1/2" or 3/4" screws, install a bracket in the center  
of each leg assembly and one at each end within 1" of but  
not over the last pocket hole (see Figure 2, page 2).  
• #2 Phillips drill bit (3 1/2" min. length)  
• Slotted screw driver  
• Measuring Tape  
• Drill Driver  
• Pencil  
If any wood pieces are missing or damaged, contact the  
dealer where you purchased this mantel for replacement.  
If hardware or trim is missing or damaged, contact DESA  
Heating Products at 1-866-672-6040 for referral informa-  
tion.YoucanalsovisitDESAHeatingProducts'technicalservice  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Attach mantel to base using 1 1/4" screws through pocket  
holes. Using brackets and 1/2" or 3/4" screws from  
bracket hardware kit, attach brackets to base and mantel  
assembly using one bracket at each back corner of leg  
sides and one on each leg front (see Figure 9).  
AssemblING tRIm  
1. Remove packaging from three pieces of trim.  
2. Locate two adjusting plates with set screws, and two  
shims in the hardware packet.  
3. Align shim under adjusting plate as shown in Figure 7.  
4. Slide one end of adjusting plate/shim in slot on mitered  
edge of top trim (see Figure 7).  
5. Adjust fireplace so that it fits into mantel opening properly.  
5. Slide other end of adjusting plate/shim in slot on mitered  
edge of side trim (see Figure 7).  
6. While firmly holding edges of trim together, tighten both  
set screws on the adjusting plate with slotted screw-  
driver.  
7. Repeat steps 2 through 6 for other corner.  
(Side view  
for clarity)  
Slot  
Set Screws  
Top Trim  
Shoulder  
Screw  
Adjusting  
Plate  
Mitered Edge  
Side Trim  
Shim  
Slot  
Figure 7 - assembling trim  
Gas Line  
Access Hole  
FIRePlAce INstAllAtION  
1. Fireplace should be fully assembled. See Assembling  
Fireplace in fireplace owner’s manual.  
2. Place mantel base close to installation location. See fire-  
place owner’s manual for installation clearances. Leave  
enough room to get behind mantel once fireplace and  
mantel assembly have been attached to base if installing  
a fireplace with flange.  
3. Install gas line. See Connecting to Gas Supply in fireplace  
owner’s manual. Remember to leave access to the gas  
shutoff valve somewhere on the base or where it is ac-  
cessible to the user.  
Assembled  
Possible  
Trim  
Shutoff Valve  
Locations  
Shoulder  
Mantel  
Screws  
Base  
Figure 8 - Installing Fireplace with Flange  
4. Check for leaks. See Checking Gas Connections in fire-  
place owner’s manual.  
IMPORTANT:IfyourreplacehasanailingangeseeInstalling  
FireplacewithFlange. Ifyourreplacedoesnothaveanailing  
flange see Installing Fireplace without Flange, page 4.  
11/4" Screw  
Bracket with 1/2"  
or 3/4" Screw  
Installing Fireplace with Flange  
1. Place mantel assembly on wood base and center left to  
right having back of assembly flush with back of base.  
Mark placement on base along inside front of mantel  
assembly. Remove mantel assembly from base.  
2. Position fireplace on base centering left to right between  
markings. Carefully position gas lines. IMPORTANT: Use  
caution when positioning fireplace on base as base may  
scratch.  
3. With assistance, carefully place mantel over fireplace  
(see Figure 8). Fireplace nailing flanges will be to inside  
of mantel. Align mantel with markings made previously.  
Make sure back of mantel is flush with back of mantel  
base. Adjust fireplace as necessary.  
Figure 9 - Installing Brackets to mantel Base  
119360-01B  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Fireplace with louver door: Lower bottom louver door. Use  
two screws provided in hardware package and attach fire-  
place to wooden base (see Figure 10). Close louver door  
Fireplace with fixed louver: Before installing logs or burner  
assembly (see owner’s manual) remove screws securing  
floor to assembly. Lift floor for access to bottom of fireplace.  
Use two screws provided in fireplace hardware package  
and attach fireplace base to wooden base (see Figure 11).  
Reinstall floor with screws removed previously.  
7. Place metal trim on shoulder screws. Firmly snap trim  
assembly over shoulder screws on fireplace.  
8. Carefully push mantel and base into position against  
wall.  
Installing Fireplace without Flange  
1. Place mantel assembly on wood base and center left to  
right having back of assembly flush with back of base.  
2. Attach mantel to base using 1 1/4" screws through pocket  
holes. Using brackets and 1/2" or 3/4" screws from  
bracket hardware kit, attach brackets to base and mantel  
assembly using one bracket at each back corner of leg  
sides and one on each leg front (see Figure 9, page 3).  
3. Position fireplace inside mantel (see Figure 12). Care-  
fully position gas lines. IMPORTANT: Use caution when  
positioning fireplace on base. Base may scratch easily.  
4. Fireplace with louver door: Lower bottom louver door. Use  
two screws provided in hardware package and attach  
fireplace to wooden base (see Figure 10). Close louver  
door  
Fireplace with fixed louver: Before installing logs or burner  
assembly (see owner’s manual) remove screws secur-  
ing floor to assembly. Lift floor for access to bottom of  
fireplace. Use two screws provided in fireplace hardware  
package and attach fireplace base to wooden base (see  
Figure 11). Reinstall floor with screws removed previ-  
ously.  
I
H
L
O
O
F
N
F
5. Place metal trim on shoulder screws. Firmly snap trim  
assembly over shoulder screws on fireplace.  
O
T
O
L
I P  
Bottom  
Louver Door  
6. Carefully push mantel and base into position against  
wall.  
Hole for Attaching  
Fireplace System to  
Wooden Mantel Base  
Figure 10 - attaching Fireplace to mantel and mantel Base  
(Side view  
for clarity)  
Screws  
Shoulder Screw  
Possible  
Fixed  
Louver  
Mantel  
Shutoff  
Base  
Holes are Behind Louver on  
Fireplace Bottom for Attaching  
Fireplace to Wooden Mantel  
Base.  
Valve  
Locations  
Figure 11 - Screw Locations for Fireplaces with Fixed Louver  
Shoulder  
Screws  
Assembled  
Metal Trim  
Figure 12 - Installing Fireplace without Flange  
2701 Industrial Drive  
P.O. Box 90004  
Bowling Green, KY 42102-9004  
Technical Service and Parts  
1-866-672-6040  
119360-01  
Rev. B  
07/06  
119360 01  
NOt A UPc  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edirol Musical Instrument FA 101 User Manual
Extron electronic Network Card Cable Cubby 200 User Manual
Friedrich Air Conditioner CP15F10 User Manual
Fujitsu All in One Printer DL700 User Manual
Furuno Radar Detector 1832 1932 1942 User Manual
Gaggenau Carpet Cleaner VK 230 714 User Manual
Gardena Elliptical Trainer 1242 1250 1243 1244 1245 User Manual
GE Cooktop 164D3333P235 User Manual
GE Monogram Microwave Oven ZEM200BF User Manual
Gigabyte Personal Computer GA K8VT800 RH User Manual