IN1502
Video Scaler
68-1205-01 Rev. D
02 08
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
providereasonableprotectionagainstharmfulinterferencewhentheequipmentisoperatedinacommercial environment. Thisequipmentgenerates, usesandcan
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own
expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions
limits.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start — IN1502
Installation
Main menus
Step 1
Power
on
See the application example below. Turn off power
to the scaler and input and output devices, and re-
move power cords from them.
INPUT 1
CMPOSITE
Step 2
Install the four rubber feet on the bottom of the
IN1502 scaler, or mount the scaler in a rack.
2 sec.
60-726-1
FW v.1.00
EXTRON
IN1502
2 sec.
2 sec.
Step 3
2 sec.
Attach input devices to the scaler.
2 sec.
NO
SIGNAL
INPUT 1
CMPOSITE
1360 x
765 @60
DEFAULT CYCLE
2 sec.
2 sec.
NOTE
Rear panel video inputs
Input 1: Composite video
I
COMPOSITE
1
S-VIDEO
N
P
U
T
The No Signal default
menu only occurs if
there is no signal
present at the currently
selected input.
S
2
MENU
Input 2: S-video
PICTURE
CONTROL
Step 4
MENU
Attach an output device to the scaler.
OUTPUT
CONFIG
RGB
Rear panel video output
MENU
O
U
T
Output 15-pin HD connector
ADVANCED
CONFIG
MENU
Step 5
EXIT
MENU
MENU
Plug the IN1502 and input and output devices into a
grounded AC source, and turn on the input and
output devices.
NEXT
Step 6
Use the LCD menu screens or RS-232 programming
to configure the scaler. See chapter 2
Output rates
for installation and operation
REMOTE
procedures, and see chapter 3 for
programming information.
Scaler Output Resolutions and Rates
Resolution
640 x 480
800 x 600
848 x 480
852 x 480
1024 x 768
1280 x 768
1360 x 765
1366 x 768
50 Hz
60 Hz
X
X
X
X
X
X
X
X
X
X
X
X
X*
X
X
X
Application example
*
The default resolution and rate is 1024 x 768 @ 60Hz.
E
T
O
M
E
R
B
G
RS-232 Control
LCD Projector
R
O
U
T
O
E
ID
V
E
IT
S
O
P
M
3
O
C
I
N
P
U
T
S
IN1502
Video Scaler
DVD
VCR
IN1502 • Quick Start QS-1
Download from Www.Somanuals.com. All Manuals Search And Download.
QS-2 IN1502 • Quick Start
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 • Introduction ...................................................................................................... 1-1
About this Manual ............................................................................................................ 1-2
About the IN1502 .............................................................................................................. 1-2
What is the IN1502? ......................................................................................................... 1-2
Controlling the IN1502 video scaler ............................................................................... 1-2
Features and Options ...................................................................................................... 1-2
Features.............................................................................................................................. 1-2
Options and accessories ................................................................................................... 1-3
Chapter 2 • Installation and Operation...................................................................... 2-1
Mounting the Scaler ........................................................................................................ 2-2
UL rack mounting requirements ..................................................................................... 2-2
Tabletop/desktop placement ........................................................................................... 2-2
Rack mounting.................................................................................................................. 2-2
Application diagram ........................................................................................................ 2-4
Rear Panel Features .......................................................................................................... 2-5
Front Panel Features ........................................................................................................ 2-6
Input selection buttons .................................................................................................... 2-6
Next button ....................................................................................................................... 2-6
Menu button ..................................................................................................................... 2-6
LCD menu display and controls ...................................................................................... 2-6
Menus, Configuration, and Adjustments............................................................ 2-7
Moving through menus by using front panel controls ............................................... 2-7
Menu overview ................................................................................................................. 2-7
Picture Control .................................................................................................................. 2-9
Brightness and contrast control.......................................................................................... 2-9
Color and tint control .......................................................................................................... 2-9
Horizontal and vertical centering control .......................................................................... 2-9
Horizontal and vertical sizing control................................................................................. 2-9
Detail control....................................................................................................................... 2-9
Output Configuration .................................................................................................... 2-10
Resolution and refresh rates ............................................................................................2-10
Sync polarity ......................................................................................................................2-10
H format ............................................................................................................................2-10
Advanced Configuration................................................................................................ 2-11
Top and bottom blanking .................................................................................................2-11
Blue mode ..........................................................................................................................2-11
Autoswitch (Autosw) mode ..............................................................................................2-11
2:2 Pulldown detection (PAL film mode detect) submenu..............................................2-12
Exit Menu ........................................................................................................................ 2-12
Optimizing the System for a DVD Player .......................................................... 2-12
Setting up a DVD source ................................................................................................ 2-12
Input Reset .......................................................................................................................... 2-13
System Reset...................................................................................................................... 2-13
i
IN1502 • Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
Front Panel Security Lockout (Executive Mode) ............................................ 2-13
IR 901 Infrared Remote Control .............................................................................. 2-14
Freeze an input ............................................................................................................... 2-14
Select an input ................................................................................................................ 2-14
Size and center ............................................................................................................... 2-14
Image adjustments ......................................................................................................... 2-14
Troubleshooting ............................................................................................................... 2-15
Operating problems ....................................................................................................... 2-15
Chapter 3 • Serial Communication................................................................................ 3-1
RS-232 Programmer’s Guide ........................................................................................ 3-2
Host-to-scaler communications ....................................................................................... 3-2
Scaler-initiated messages ................................................................................................... 3-2
Error responses ................................................................................................................... 3-2
Using the command/response tables ................................................................................. 3-3
Symbol definitions ............................................................................................................... 3-3
Command/response table for SIS commands..................................................................... 3-4
Command/response table for special function SIS commands .......................................... 3-7
Appendix A • Appendix........................................................................................................ A-1
Specifications ..................................................................................................................... A-2
Part Numbers and Accessories ................................................................................. A-4
Included parts .................................................................................................................. A-4
Accessories ........................................................................................................................ A-4
Firmware Upgrade Installation................................................................................. A-5
All trademarks mentioned in this manual are the properties of their respective owners.
68-1205-01 Rev. D
02 08
ii
IN1502 • Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
IN1502
Chapter One
1
Introduction
About this Manual
About the IN1502
Features and Options
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this Manual
This manual describes how to install, configure, and operate the Extron IN1502
video scaler and how to operate the optional IR 901 infrared remote control
(part #70-152-01).
Throughout this manual the terms “IN1502”, “video scaler”, and “scaler” are
used interchangeably to refer to the same product.
About the IN1502
What is the IN1502?
The IN1502 is a video scaler that offers 16 output rates and provides scaling
solutions for boardrooms, conference rooms, and home theaters, as well as rental
and staging applications.
To enable superior scaling performance, the IN1502 features several of Extron’s
patented and patent-pending technologies, including Dynamic Motion
Interpolation (DMI™) technology, and 3:2 and 2:2 pulldown detection. DMI is an
advanced motion detection and compensation method that enables image
enhancement with no loss of image fidelity.
The IN1502 scales composite video and S-video up to computer video (RGBHV/
RGBS), which can be output to a display device via a 15-pin HD connector.
Controlling the IN1502 video scaler
The IN1502 can be controlled using one or more of the following methods:
• The front panel controls
• A computer, a touch screen panel, or any other device that can send and
receive the serial communications through the RS-232 port. Extron’s
Simple Instruction Set (SIS™) is a set of simple keystroke commands that
can be used with any such devices.
• The optional IR 901 remote control, which has most of the front panel controls
Features and Options
Features
Two video inputs
•
Input 1 — One BNC connector on the rear panel accepts a composite video
signal.
•
Input 2 — One 4-pin DIN connector on the rear panel accepts an S-video
signal.
Video output — One VGA-type 15-pin HD connector provides an RGB output.
Three ways to control the scaler — The scaler’s front panel, a computer or other
RS-232 control device, or the optional IR 901 remote control can all be used
to control the scaler.
Scaled outputs — The IN1502 offers 16 different output rates.
RS-232 configuration — The IN1502 can be configured by using a control
system.
Dynamic Motion Interpolation (DMI) — This video processing technique is an
advanced motion prediction and compensation method that treats motion
content and still content with different algorithms to yield high fidelity
images.
1-2
IN1502 • Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
3:2 pulldown detection for NTSC and 2:2 film detection for PAL video
sources — These advanced film mode processing features help maximize
image detail and sharpness for video sources that originated from film.
When film is converted to NTSC video, the film frame rate has to be
matched to the video frame rate in a process called 3:2 pulldown. Jaggies
and other image artifacts can result if conventional deinterlacing
techniques are used on film-source video. The IN1502’s advanced film
mode processing recognizes signals that originated from film. The
IN1502 then applies video processing algorithms that optimize the
conversion of video that was made with the 3:2 pulldown process. This
results in richly detailed images with sharply defined lines. A similar
process is used for PAL film-source video.
Versatile mounting options — The IN1502 is 1U high, and a half rack wide. It is
rack mountable, or it can be placed on a table or other furniture. Rubber
feet are included.
Options and accessories
The IN1502’s optional equipment includes:
• IR 901 remote control — Extron’s IR 901 (part #70-152-01) is an infrared
remote control which replicates all of the front panel controls of the
IN1502 except the Menu and Next buttons.
• Rack shelf mounting kit — The 1U high, half rack width IN1502 can be rack
mounted using the universal rack shelf mounting kit (part #60-190-01) or
the basic rack shelf mounting kit (part #60-604-01).
IN1502 • Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
1-4
IN1502 • Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
IN1502
Chapter Two
Installation and Operation
2
Mounting the Scaler
Rear Panel Features
Front Panel Features
Menus, Configuration, and Adjustments
Optimizing the System for a DVD Player
Input Reset
System Reset
Front Panel Security Lockout (Executive Mode)
IR 901 Infrared Remote Control
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
Mounting the Scaler
UL rack mounting requirements
The following Underwriters Laboratories (UL) requirements pertain to the safe
installation of the IN1502 in a rack.
1.
Elevated operating ambient temperature — If installed in a closed or
multi-unit rack assembly, the operating ambient temperature of the rack
environment may be greater than room ambient temperature. Therefore,
install the IN1502 in an environment compatible with the maximum
ambient temperature (Tma = +113 °F, +45 °C) specified by Extron.
2.
3.
4.
Reduced air flow — Install the equipment in a rack so that the amount of
air flow required for safe operation of the equipment is not compromised.
Mechanical loading — Mount the equipment in the rack so that a
hazardous condition is not achieved due to uneven mechanical loading.
Circuit overloading — Connect the equipment to the supply circuit and
consider the effect that circuit overloading might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
5.
Reliable earthing (grounding) — Maintain reliable grounding of rack-
mounted equipment. Pay particular attention to supply connections other
than direct connections to the branch circuit (e.g. use of power strips).
Tabletop/desktop placement
For tabletop or desktop placement only, install the self-adhesive rubber feet/pads
(provided) onto the four corners of the bottom of the enclosure.
Rack mounting
1.
If feet were installed on the bottom of the IN1502, remove them.
2.
Place the IN1502 on one half of the 1U (one unit high, one unit wide) rack
shelf (part #60-190-01 or #60-604-01). Align the front of the IN1502 with
the front of the shelf, and align the threaded holes on the bottom of the
IN1502 with the holes in the rack shelf.
3.
Attach the IN1502 to the rack shelf with the two provided 4-40 x 3/16"
machine screws. Insert the screws from the underside of the shelf, and
securely fasten them into diagonally-opposite corners.
See the following illustration.
2-2
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
Front false
faceplate
uses 2
screws.
(2) 4-40 x 3/16"
Screws
NOTE: Using screws longer
than 3/16” will damage the
unit and void the warranty.
Use 2 mounting holes on
opposite corners.
Rack mounting the IN1502
4.
5.
Attach the false front panel (provided with rack shelf part #60-190-01) to
the unoccupied side of the rack (as shown above), or install a second half-
rack-width device in that side by repeating steps 1 through 3.
Attach the rack shelf to the rack using four 10-32 x ¾" bolts (provided).
Insert the bolts through #10 beveled washers, then through the holes in the
rack, as shown above.
IN1502 • Installation and Operation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Application diagram
The diagram shown below is an example of a typical IN1502 application with
cable connections.
E
T
O
M
E
R
B
G
RS-232 Control
R
O
U
T
O
E
ID
V
E
IT
S
O
P
3
M
O
C
I
N
P
U
T
S
IN1502
Video Scaler
LCD Projector
DVD
VCR
Application diagram example of the IN1502
2-4
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel Features
The rear panel of the IN1502 is shown below.
REMOTE
RGB
100-240V
0.3A
5
I
COMPOSITE
S-VIDEO
N
P
U
T
S
O
U
T
1
2
50/60 Hz
1
2
3
4
IN1502 rear panel connectors
AC power connector — Plug a standard IEC power cord into this connector
to connect the scaler to a 100 to 240 VAC, 50 Hz or 60 Hz power source.
The front panel LCD display and input selection LEDs will light during
power-up.
1
Video input 1: Composite video — Connect a composite video signal to this
female BNC connector.
2
Video input 2: S-video — Connect an S-video signal to this 4-pin mini-DIN
3
female connector.
RGB 15-pin HD video output — Connect an RGB video display.
4
5
Remote (RS-232/contact closure) 9-pin port — This connector provides for
two-way RS-232 communication and contact closure control. See chapter 3,
“Serial Communication”, for information on how to use the SIS commands.
The default protocol is 9600 baud, 1 stop bit, no parity, and no flow control.
The rear panel RS-232 9-pin D female connector has the following pin
assignments:
Pin RS-232 function Description
1
2
3
4
5
6
7
8
9
–
Tx
Rx
No connection
Transmit data
Receive data
Contact closure
Signal ground
Contact closure
No connection
No connection
IR input
5
1
Input #1
Gnd
Input #2
9
6
DB9 Pin Locations
Female
–
–
Hardwired IR
The Remote connector also provides a way to select an input using a remote
contact closure device. Contact closure control uses pins on the Remote
connector that are not used by the RS-232 interface (see preceding the table).
To select a different input number using a contact closure device,
momentarily short the pin for the desired input number to logic ground
(pin 5). To force one of the inputs to be always selected, leave the short to
logic ground in place. The short overrides front panel input selections.
IN1502 • Installation and Operation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Front Panel Features
The front panel of the IN1502 is shown below.
4
MENU
1
2
ADJUST
IR
NEXT
IN 1502
VIDEO SCALER
1
3
6
2
5
7
IN1502 front panel
Input selection buttons
Input 1 can only input composite video; Input 2 can only input S-video.
Composite input button — This button selects the composite video input
1
2
(Input 1). The LED lights green when this input is selected.
S-video input button — This button selects the S-video input (Input 2). The
LED lights green when this input is selected.
Next button
Next button — Use this button to step through the submenus in the
3
IN1502 menu system. See the “Menus, Configuration, and Adjustments”
section in this chapter for details.
Menu button
Menu button — Use this button to enter and move through the main menu
4
system in the IN1502. See the “Menus, Configuration, and Adjustments”
section in this chapter for details.
LCD menu display and controls
LCD — Displays configuration menus and status information. See the
5
“Menus, Configuration, and Adjustments” section in this chapter for
details.
Horizontal Adjust ( ) knob — In the menu system, rotate this knob to
6
7
scroll through menu options and make adjustments.
Vertical Adjust ( ) knob — In the menu system, rotate this knob to scroll
through menu options and make adjustments.
2-6
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Menus, Configuration, and Adjustments
Scaler configuration and adjustments can be performed by using the front panel
controls and the menus that are displayed on the IN1502’s LCD screen. These
menus are used primarily when the scaler is first set up.
Moving through menus by using front panel controls
Menu button — Press the Menu button to activate menus and to scroll to the
four main menus.
Next button — Press the Next button to move between the submenus of a
selected main menu. Pressing the Next button during input configuration
causes the current input’s number and format type to be displayed on the
LCD.
Adjust (
,
) knobs — In configuration mode, rotate the horizontal Adjust (
)
knob and vertical Adjust ( ) knob to scroll through submenu options and to
make adjustment selections. Refer to the flowcharts in this chapter and to
specific sections for explanations on knob adjustments.
The Adjust knobs have no mechanical limits to their rotation.
Menu overview
After the initial power up menus display, the default menus appear on the LCD
screen when no adjustments are actively being made. They cycle between the
menu screen showing the active input’s number and video format, and the menu
screen showing the output rate, as shown in the example flowchart below.
Power
on
60-726-1
FW v.1.00
EXTRON
IN1502
INPUT 1
CMPOSITE
2 sec.
2 sec.
2 sec.
INPUT 1
CMPOSITE
2 sec.
NO
SIGNAL
1360 x
765 @60
DEFAULT CYCLE
2 sec.
2 sec.
NOTE
2 sec.
The No Signal default menu
only occurs if there is no
signal present at the currently
selected input connector.
Default menus
The No Signal default menu only occurs if there is no signal present at the
currently selected input connector.
From any menu or submenu, after ten seconds of inactivity the IN1502 saves
all adjustment settings and times out to the default menus.
IN1502 • Installation and Operation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
The main menus are as shown in the following flowchart. Use the Menu key to
scroll between them.
Power
on
60-726-1
FW v.1.00
EXTRON
IN1502
INPUT 1
CMPOSITE
2 sec.
2 sec.
2 sec.
2 sec.
DEFAULT CYCLE
2
s e c .
NO
SIGNAL
INPUT 1
CMPOSITE
1360 x
765 @60
2
s e c .
2 sec.
The No Signal default menu
only occurs if there is no
signal present at the currently
selected input connector.
NOTE
MENU
PICTURE
CONTROL
MENU
OUTPUT
CONFIG
MENU
ADVANCED
CONFIG
MENU
EXIT
MENU
MENU
NEXT
Main menus
To return to the default screens, let the IN1502 time-out for 10 seconds, or
press the Menu button until the Exit Menu menu appears, then press the Next
button.
Submenus are accessed from a main menu by pressing the Next button. If
you press the Menu button while a submenu is active, the next main menu
becomes active. For example, the menu changes from the Output
Configuration menu or its submenus to the Advanced Configuration main
menu.
2-8
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Control
The following flowchart provides an overview of the Picture Control submenus
and the options for each setting.
Default
Cycle
MENU
PICTURE
CONTROL
H
128
CNTR V
128
BRT CONT
COL TINT
128 128
NEXT
NEXT
NEXT
NEXT
128
128
Brightness and Contrast
Color and Tint
Horizontal and Vertical Centering
•
Brightness ranges from 000 to 255.
The default is 128.
•
Color ranges from 000 to 255.
The default is 128.
•
Horizontal centering ranges from 000 to
255. The default is 128.
•
Contrast ranges from 000 to 255.
The default is 128.
•
Vertical centering ranges from 000 to 255.
The default is 128.
•
Tint ranges from 000 to 255.
The default is 128.
DETAIL
016
H
.
SIZE V
NEXT
NEXT
.
Horizontal and Vertical Sizing
Detail
Detail (sharpness) ranges from
000 to 63. The default is 16.
•
Adjust horizontal and vertical sizing while
observing the display.
•
Brightness and contrast control
This submenu allows adjustment of the brightness and contrast of the output
display. The adjustment ranges from 0 to 255. The default is 128.
Rotate the horizontal Adjust ( ) knob to adjust the brightness and use the
vertical Adjust ( ) knob to adjust the contrast of the output display.
Color and tint control
This submenu allows adjustment of the color and tint of the output display. The
adjustment ranges from 0 to 255. The default is 128.
Rotate the horizontal Adjust ( ) knob to adjust the color and use the vertical
Adjust ( ) knob to adjust the tint of the output display.
Horizontal and vertical centering control
This submenu allows adjustment of the horizontal and vertical centering of the
output display. The adjustment ranges from 0 to 255. The default is 128.
Rotate the horizontal Adjust ( ) knob to adjust the horizontal centering and use
the vertical Adjust ( ) knob to adjust the vertical centering of the output display.
Horizontal and vertical sizing control
This submenu allows adjustment of the horizontal and vertical sizing of the
output display.
Rotate the horizontal Adjust ( ) knob to adjust the horizontal sizing and use
the vertical Adjust ( ) knob to adjust the vertical sizing of the output display.
Detail control
This submenu allows adjustment of the image detail (sharpness) of the output
display. The adjustment ranges from 0 to 63. The default is 16.
Using either the horizontal Adjust ( ) or vertical Adjust ( ) knob, adjust the
detail while observing the output display.
IN1502 • Installation and Operation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Output Configuration
The following flowchart provides an overview of the Output Configuration
submenus and the options for each setting.
Default
Cycle
MENU
PICTURE
CONTROL
MENU
OUTPUT
CONFIG
H FORMAT
<H> HV
1024 x
768 @60
H
NEG
SYNC
V
NEXT
NEXT
NEXT
NEXT
POS
Scaler output rates
• See the scaler output table in this
chapter for available combinations of
resolutions and refresh rates.
Select sync output format
Sync polarity combinations
•
H+/V-
•
•
H (default) – specify horizontal sync
HV – specify composite sync
•
•
H-/V- (default)
H-/V+
•
H+/V+
Default: 1024 x 768 @60 Hz
NEXT
Resolution and refresh rates
Rotate the horizontal Adjust ( ) knob while in this submenu to select one of the
available combinations of output resolution rates.
Rotate the vertical Adjust ( ) knob while in this submenu to select one of the
available refresh (vertical scanning) rates.
Scaler Output Resolutions and Rates
Resolution
640 x 480
800 x 600
848 x 480
852 x 480
1024 x 768
1280 x 768
1360 x 765
1366 x 768
50 Hz
60 Hz
X
X
X
X
X
X
X
X
X
X
X
X
X*
X
X
X
*
The default resolution and rate is 1024 x 768 @ 60Hz.
Sync polarity
The display or projector may require a particular combination of horizontal (H)
and vertical (V) sync signal polarities. Select the appropriate combination of
positive or negative H and V sync by rotating either the horizontal Adjust ( ) or
vertical Adjust ( ) knob.
H format
To output composite sync, select “HV” as the H Format. Select “H” to output
horizontal sync.
Select either H or HV by rotating either the horizontal Adjust ( ) or vertical
Adjust ( ) knob. The default is “H”.
2-10
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Configuration
The following flowchart provides an overview of the Advanced Configuration
submenus and the options for each setting.
Default
Cycle
MENU
PICTURE
CONTROL
MENU
OUTPUT
CONFIG
MENU
T
000
BLNK
B
000
BLUEMODE
<OFF> ON
ADVANCED
CONFIG
NEXT
NEXT
NEXT
Top and bottom blanking
Display blue and sync only
•
Top blanking ranges from 000 (default)
to 127
Bottom blanking ranges from 000 (default)
• On
• Off (default)
•
to 127
2:2 PLDN
NEXT
AUTOSW
<OFF> ON
NEXT
<OFF> ON
PAL film mode (2:2 pulldown detection)
Autoswitch mode
• On
• On
• Off (default)
• Off (default)
Top and bottom blanking
To remove noise or extraneous material, such as closed captioning, remove scan
lines at either the top or bottom of the screen. Rotate the horizontal Adjust (
)
knob to adjust the top blanking from 0 to 127 lines. The default is 0. Rotate the
vertical Adjust ( ) knob to adjust the bottom blanking from 0 to 127 lines. The
default is 0.
Blue mode
To aid in setup of the scaler’s color and tint, the Blue mode can be set from this
submenu to “On” so that only sync and blue video signals are passed to the
display.
Use either the horizontal Adjust ( ) or vertical Adjust ( ) knob to specify this
mode. The default is “Off”.
Autoswitch (Autosw) mode
The Autoswitch mode causes the highest numbered input that has a signal
present to be automatically selected. For example, if both Inputs 1 and 2 have
active input signals, Input 2 is selected.
From this submenu, use either the horizontal Adjust ( ) or vertical Adjust ( )
knob to specify this mode as “On” or “Off”. The default is “Off”.
IN1502 • Installation and Operation 2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
2:2 Pulldown detection (PAL film mode detect) submenu
For the currently selected input, set this feature to “On” if the source is PAL video
that originated in film. For standard PAL video sources, such as cameras, set this
feature to “Off” (default).
This feature does not apply to NTSC video sources since film
mode (3:2 pulldown) is automatically detected for those signals.
From this submenu, use either the horizontal Adjust ( ) knob or vertical
Adjust ( ) knob to specify this mode as “On” or “Off”.
Exit Menu
From this submenu, press the Next button to return to the Default menu cycle, or
press the Menu button to return to the Picture Control menu.
Default
Cycle
MENU
PICTURE
CONTROL
MENU
OUTPUT
CONFIG
MENU
ADVANCED
CONFIG
MENU
EXIT
MENU
MENU
NEXT
Optimizing the System for a DVD Player
For optimal performance, follow the steps in this section in order when setting
up the IN1502 for a DVD player.
Setting up a DVD source
To get the best results when using a DVD as a video source, Extron recommends
that the DVD player itself be set up to output an aspect ratio of 16:9 and not 4:3.
Because all DVDs are mastered as 16:9, having them set up for anything else will
cause the player to internally scale and compress the signal. This scaling/
compression by the DVD player will defeat the advantage of having 3:2
pulldown detection in the IN1502.
All sizing adjustments to correct aspect ratio should be done using the IN1502.
To change the output aspect ratio of most DVD players,
1.
2.
Enter the DVD player’s Setup or Action menu while the disc is stopped.
Select a 16:9 aspect ratio.
2-12
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Reset
To reset each input of the IN1502 scaler to its default centering and sizing values,
hold down the specific input button until the Input # Reset message is displayed
on the LCD screen.
Autoswitch must be set to “OFF” before Input Reset can activated. See
“Autoswitch (Autosw) mode” in the “Advanced Configuration” section of
this chapter.
System Reset
To reset the IN1502 to all of its default values, hold down the Input 1 button
while simultaneously plugging in the power cord. The System Reset message is
displayed on the LCD screen.
Front Panel Security Lockout (Executive Mode)
To prevent accidental changes to settings, press the Menu and Next buttons
simultaneously for 2 seconds to enable the IN1502’s Executive mode. Executive
mode locks all front panel functions except the the input buttons. The menu
system still returns to the Default menu when 10 seconds have elapsed. When
Executive mode is active, all functions and adjustments can still be made
through RS-232 control. For details on RS-232 control, see chapter 3, “Serial
Commnication”.
To disable the Executive mode, press the Menu and Next buttons simultaneously
for 2 seconds.
Enable Executive Mode
Disable Executive Mode
Default
Cycle
Default
Cycle
Press for
Press for
2 seconds
2 seconds
MENU
MENU
NEXT
NEXT
EXE MODE
ENABLED
EXE MODE
DISABLED
10 sec.
timeout
10 sec.
timeout
The input selection buttons (Input 1 and Input 2) remain functional during
Executive mode.
IN1502 • Installation and Operation 2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
IR 901 Infrared Remote Control
The IR 901, shown at right, replicates all of the front
panel controls except the Menu and Next buttons. If
Executive mode has been enabled on the IN1502, input
selection and adjustments can still be made from the
IR 901. You must use the IN1502’s front panel, a host
computer, or an RS-232 control device to configure and
program the scaler. See chapter 3, “Serial
Communication”, for details.
The topmost part of the IR 901 features three Aspect
Ratio Preset buttons (not functional), a Freeze button,
and two input selection buttons (1 and 2). Inputs 3, 4,
5, and 6, and the Take button are not functional. The
middle portion of the IR 901 features the size and
centering buttons. The bottom part contains the
adjustment controls for color, tint, brightness, contrast,
and detail adjustments. The sharpness buttons are not
functional.
Freeze an input
To freeze the input being displayed, press the Freeze
On/Off button. To unfreeze the input, press the Freeze
button again.
Select an input
To select an input source, press an input button
(1 or 2).
Size and center
Use the Size and Center buttons to adjust the sizing and centering aspects of a
displayed image.
Image adjustments
The color, tint, brightness, contrast, and detail of a displayed image may be
increased or decreased by using the appropriate Image Adjustment buttons at the
bottom of the IR 901.
2-14
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
This section gives recommendations on what to do if you have problems
operating the IN1502, and it provides examples and descriptions for some image
problems you might encounter.
The following are some tips to help you in troubleshooting.
1.
Some symptoms may resemble others, so you may want to look through all
of the examples before attempting to solve the problem.
2.
3.
Be prepared to backtrack in case the action taken doesn’t solve the problem.
It may help to keep notes and sketches in case the troubleshooting process
gets lengthy. This will also give you something to discuss if you call for
technical support.
4.
5.
Try simplifying the system by eliminating components that may have
introduced the problem or made it more complicated.
For sync-related problems: Portable digital projectors are designed to
operate close to the video source. Sync problems may result from using
long cables or from improper termination. A sync adapter, such as Extron’s
ASTA (active sync termination adapter), may help solve these problems.
6.
For LCD and DLP projectors and plasma displays: In addition to the sync-
related information above, check the user’s manual that came with the
projector for troubleshooting tips, as well as for settings and adjustments.
Each manufacturer may have its own terms, so look for terms like “auto
setup”, “auto sync”, “pixel phase”, and “tracking”.
Operating problems
The table below shows some common operating problems and their solutions.
Problem
Cause
Solution
No image appears.
The input signal is
incompatible.
Attach an input device that is
compatible with NTSC 3.58,
NTSC 4.43, PAL, or SECAM.
Freeze mode was
entered when the
image was black.
Deactivate freeze mode.
The scaled output
rate is too high for
the display.
Change the scaled output to a
compatible resolution.
The image is frozen.
Freeze mode is on.
Deactivate freeze mode.
If that does not work, unplug the
power cord from the scaler, then
plug it back in.
The image is flashing. The scaled output
rate is too high for
Change the scaled output to a
compatible resolution.
the display.
The image is too soft.
The detail level
needs to be
changed.
Change the detail level.
IN1502 • Installation and Operation 2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
2-16
IN1502 • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
IN1502
Chapter Three
3
Serial Communication
RS-232 Programmer’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Communication
The IN1502 can be remotely controlled via a host computer or other device (such
as a control system) attached to the rear panel Remote connector. The control
device (host) uses Extron’s Simple Instruction Set (SIS) commands.
The scaler uses a protocol of 9600 baud, 1 stop bit, no parity, and no flow control.
The rear panel RS-232 9-pin D connector has the following pin assignments:
Pin RS-232 function Description
1
2
3
4
5
6
7
8
9
–
Tx
Rx
No connection
Transmit data
Receive data
Contact closure
Signal ground
Contact closure
No connection
No connection
IR input
5
1
Input #1
Gnd
Input #2
9
6
DB9 Pin Locations
Female
–
–
Hardwired IR
RS-232 Programmer’s Guide
Host-to-scaler communications
SIS commands consist of one or more characters per field. No special characters
are required to begin or end a command sequence. When the IN1502 determines
that a command is valid, it executes the command and sends a response to the
host device. All responses from the scaler to the host end with a carriage return
and a line feed (CR/LF = ), which signals the end of the response character
string. A string is one or more characters.
It is also possible to send several SIS commands back-to-back in sequence.
Scaler-initiated messages
When a local event such as a front panel selection or adjustment takes place, the
IN1502 scaler responds by sending a message to the host. No response is
required from the host. The scaler-initiated messages are listed here
(underlined).
(C) Copyright 2005, Extron Electronics, IN1502, Vx.xx
The IN1502 sends the copyright message when it first powers on. Vx.xx is the
firmware version number.
X1
X1
C hn
(where
is the input number)
The IN1502 sends this response when an input is switched.
Error responses
When the scaler receives a valid SIS command, it executes the command and
sends a response to the host device. If the IN1502 is unable to execute the
command because the command is invalid or it contains invalid parameters, it
returns an error response to the host.
The error response codes and their descriptions are as follows:
E01 – Invalid input channel number
E10 – Invalid command
E13 – Invalid value (the number is out of range/too large)
3-2
IN1502 • Serial Communication
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the command/response tables
The command/response tables on the next page list valid command ASCII codes,
the scaler’s responses to the host, and a description of the command’s function
or the results of executing the command. Uppercase and lowercase characters
may be used interchangeably in the command field.
The ASCII to HEX conversion
table at left is for use with the
ASCII to HEX Conversion Table
command/response tables.
•
ASCII to Hex conversion table
The command/response tables use symbols (defined below) to represent variables.
Symbol definitions
=
=
=
=
CR/LF (carriage return/line feed) (hex 0D 0A)
•
Space
Escape key
Esc
X1
Specific input number (1 or 2)
1 = input 1
2 = input 2
X2
=
=
=
=
0 = off, 1 = on
Picture adjustment range (0 through 255)
Sharpness level (details) (0 through 63)
X3
X4
X5
Scaler resolution
1 = 640 x 480
2 = 800 x 600
3 = 848 x 480
4 = 852 x 480
5 = 1024 x 768
6 = 1280 x 768
7 = 1360 x 765
8 = 1366 x 768
=
Detected input signal standard (0 through 4)
X6
0 = none
1 = NTSC 3.58
2 = PAL
3 = NTSC 4.43
4 = SECAM
=
=
Blanking adjustment range (0 through 127 lines)
X7
X8
Scaler refresh rate
1 = 50 Hz
2 = 60 Hz
IN1502 • Serial Communication
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Communication, cont’d
Command/response table for SIS commands
Command
ASCII Command Response
Additional description
(host to scaler)
(scaler to host)
Input selection
Select video input
Example:
X1
X1
X1
!
C
Video Input
.
1!
C1
Example: select video Input 1.
Color
X3
X3
Set a specific color value
C
Col
Set the color adjustment level
X3
to
.
Example:
47C
+C
Col047
Example: set the color adjustment to 47.
X3
Increment
Col
Select the next higher color
adjustment level.
X3
Decrement
-C
C
Col
Select the next lower color
adjustment level.
X3
View the color value
Col
Show the current color
adjustment level.
Tint
X3
X3
Set a specific tint value
T
Tin
Set the tint adjustment level to
X3
.
Example:
76T
+T
Tin76
Example: set the tint to 76.
X3
Increment
Tin
Select the next higher tint
adjustment level.
X3
Decrement
-T
T
Tin
Select the next lower tint
adjustment level.
X3
View the tint value
Tin
Show the current tint
adjustment level.
Contrast
X3
X3
Set a specific contrast value
^
Con
Set the contrast adjustment
X3
to
.
X3
Increment
+^
-^
^
Con
Select the next higher contrast
adjustment level.
X3
Decrement
Con
Select the next lower contrast
adjustment level.
X3
View the contrast value
Con
Show the current contrast
adjustment level.
Brightness
X3
X3
Set a specific brightness value
Y
Brt
Set the brightness adjustment to
X3
.
X3
Increment
+Y
-Y
Y
Brt
Select the next higher brightness
adjustment level.
X3
Decrement
Brt
Select the next lower brightness
adjustment level.
X3
View the brightness value
Brt
Show the current brightness
adjustment level.
Detail mode
Set the detail level
Increment
X4
X4
X4
D
Det
Set the detail level to
.
X4
+D
-D
D
Det
Increment the detail setting.
Decrement the detail setting.
Show the detail setting.
X4
Decrement
Det
X4
View the detail value
Det
3-4
IN1502 • Serial Communication
Download from Www.Somanuals.com. All Manuals Search And Download.
Command/response table for SIS commands (continued)
Command
ASCII Command Response
Additional description
(host to scaler)
(scaler to host)
Horizontal shift
X3
X3
Set horizontal position
H
Hph
Set the horizontal centering to
X3
.
X3
Increment the shift value
Decrement the shift value
View the horizontal position
+H
-H
H
Hph
Shift right.
X3
Hph
Shift left.
X3
Hph
Show the horizontal position.
Vertical shift
X3
X3
X3
Set the vertical position
Increment the shift value
Decrement the shift value
View the vertical position
/
Vph
Set the vertical centering to
Shift up.
.
X3
+/
-/
/
Vph
X3
Vph
Shift down.
X3
Vph
Show the vertical position.
Horizontal size
Increase the horizontal size
Decrease the horizontal size
+:
-:
Hsz +
Hsz -
Widen the picture.
Make the picture narrower.
Vertical size
Increase the vertical size
Decrease the vertical size
+;
-;
Vsz +
Vsz -
Make the picture taller.
Make the picture shorter.
Top blanking
X7
X7
Specify a top blanking value
(
Blt
Set the number of lines to
blank at the top of the picture.
X7
Increase the top blanking value
Decrease the top blanking value
View the top blanking value
+(
-(
(
Blt
Increase the number of top lines
blanked.
X7
Blt
Decrease the number of top
lines blanked.
X7
Blt
Show the number of lines that
are blanked at the top of the
picture.
Bottom blanking
X7
X7
Specify a bottom blanking value
)
Blb
Set the number of lines to
blank at the bottom of the
picture.
X7
Increase the bottom blanking value +)
Decrease the bottom blanking value -)
Blb
Increase the number of lines
blanked at the bottom.
X7
Blb
Decrease the number of
bottom lines blanked.
X7
View the bottom blanking value
)
Blb
Show the # of bottom lines
that are blanked.
Scaler rate
X5
X8
X5
X5
X8
X8
Set the output rate
View the output rate
*
=
Rte
Rte
*
*
Select a scaler output scan rate.
Show the scaler output rate.
=
Video mute
Mute on
0B
0B
1B
B
Vmt 0
Vmt0
Vmt 1
Mute video output.
Example:
Mute off
Unmute video output.
X2
View video mute status
Vmt
Show the video mute status.
IN1502 • Serial Communication
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Communication, cont’d
Command/response table for SIS commands (continued)
Command
ASCII Command Response
Additional description
(host to scaler)
(scaler to host)
Freeze
Enable
1F
0F
Frz1
Frz0
Output a “frozen” video
image.
Disable
Turn off freeze (output
motion).
X2
View the freeze status
f/F
F
Frz
Show the freeze status.
Example:
Frz 0
Example: Freeze is disabled.
Front panel security lockout (Executive mode)
Enable (lock image adjustments) 1X
Exe1
Exe0
Lock front panel adjustments;
adjust image via RS-232 only.
Disable
0X
Adjustments and selections
are made from the front panel.
X2
View the executive mode status
X
X
Exe
Show executive mode status.
Example:
Exe 1
Example: The front panel is
locked.
Software version and build number requests
Query software version number
Show version and build number
Q/q
*Q
x.xx
Show the software version.
x.xxx.xxx
Show the version and build
number.
Part number request
Show the DVS 202’s part number N/n
60-726-01
Show the scaler’s part number.
Information request
X1
X6
Show the current input number
I/i
Chn •Std
Show the scaler’s input
number and signal standard.
Zap (reset to default settings)
Esc
Total reset
zXXX
zI
ZapXXX
ZapI
Reset everything: all settings
and adjustments to the factory
default.
Esc
Image adjustment reset
Reset image adjustments to
factory settings.
3-6
IN1502 • Serial Communication
Download from Www.Somanuals.com. All Manuals Search And Download.
X?
X!
X?
X!
The syntax for setting a special function is
*
# where
is the function number and
is the
X?
X?
value. To view a function’s setting, use
# where
is the function number. In the following table the
X?
values of the
variable are different for each command/function. These values are given in the
rightmost column.
Command/response table for special function SIS commands
X!
Command
ASCII Command Response
values
(host to scaler)
(scaler to host)
and additional descriptions
PAL file mode (2:2 pulldown detction)
Set mode on
18*1#
18*0#
18#
PDn1
PDn0
Set PAL file mode on.
Set mode off
Set PAL file mode off.
Show PAL file mode status.
X2
View file mode status
PDn
Blue mode
Set Blue mode on
Set Blue mode off
View Blue mode status
8*1#
8*0#
8#
Blu1
Blu0
Set Blue mode on.
Set Blue mode off.
Show Blue mode status.
X2
Blu
Auto switch
Set Auto switch mode on
Set Auto switch mode off
View Auto switch mode status
10*1#
10*0#
10#
Aut1
Aut0
Set Auto switch mode on.
Set Auto switch mode off.
X2
Aut
Show Auto switch mode
status.
H Format (sync output format)
Set to horizontal sync
Set to composite sync
View H Format status
15*1#
HFm0
HFm1
Set H format to off/0
(horizontal sync, default).
15*0#
15#
Set H format to on/1
(composite sync).
X2
HFm
Show H format mode status.
IN1502 • Serial Communication
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial Communication, cont’d
3-8
IN1502 • Serial Communication
Download from Www.Somanuals.com. All Manuals Search And Download.
IN1502
Appendix
A
Appendix
Specifications
Part Numbers and Accessories
Firmware Upgrade Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Video input
Number/signal type .................. 1 S-video
1 composite video
Connectors .................................. (1) 4-pin mini DIN female (S-video)
1 BNC female (composite video)
Nominal level ............................... 1 Vp-p for Y of S-video and for composite video
0.3 Vp-p for C of S-video
Minimum/maximum levels ...... Analog: 0.0 V to 1.0 Vp-p with no offset
Impedance ................................... 75 ohms
Horizontal frequency .................. NTSC 3.58, NTSC 4.43, PAL, SECAM
Vertical frequency ....................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Resolution range .......................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Return loss .................................... <-25 dB @ 5 MHz
DC offset (max. allowable) ......... 1.5 V
Video processing
Decoder ......................................... 9 bit digital
Digitalsampling ........................... 24 bit, 8 bits per color; 13.5 MHz standard
Colors ............................................ 16.78 million
Video output
Number/signal type .................. 1 scaled RGBHV, RGBS
Connectors .................................. 1 female 15-pin HD
Nominal level ............................... 0.7 Vp-p for RGB
Minimum/maximum levels ...... 0.0 V to 0.7 Vp-p
Impedance .................................... 75 ohms
Scaled resolutions ........................ 640x4801,2, 800x6001,2, 848x4801,2, 852x4801,2, 1024x7681,2, 1280x7681,2,
1360x7651,2, 1366x7681,2
1 = at 50 Hz 2 = at 60 Hz
Sync
Output type .................................. RGBHV, RGBS
Standards ...................................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level ..................................... 0 V to 1.0 Vp-p
Outputlevel .................................. TTL: 5.0 Vp-p, unterminated
Input impedance .......................... 75 ohms
Outputimpedance ....................... 75 ohms
Max input voltage ........................ 5 Vp-p
Max. propagation delay .............. 20 ns
Polarity .......................................... Negative
Control/remote — decoder/scaler
Serial control port ........................ RS-232, 9-pin female D connector
Baud rate and protocol ............... 9600 baud, 8 data bits, 1 stop bit, no parity
Serial control pin configurations 2 = TX
3 = RX
4 = input 1 select (contact closure)
5 = GND
6 = input 2 select (contact closure)
Contact closure ............................ 9-pin female D connector (same as RS-232 connector)
A-2
IN1502 • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact closure pin configurations See pins 4, 5, and 6 above.
IR controller module ................... Extron IR 901 (optional)
Program control .......................... Extron’s Simple Instruction Set (SIS™)
General
Power ............................................ 100 VAC to 240 VAC, 50/60 Hz, 30 watts, internal, autoswitchable
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +113 °F (0 to +45 °C) / 10% to 90%, noncondensing
Rack mount .................................. Yes, with optional rack shelf, part #60-190-01
Enclosure type .............................. Metal
Enclosure dimensions ................. 1.75" H x 8.75" W x 9.5" D (1U high, half rack wide)
4.4 cm H x 22.2 cm W x 24.1 cm D
(Depth excludes connectors and knobs. Width excludes rack ears.)
Product weight ............................. 3.3 lbs (1.5 kg)
Shipping weight ........................... 6 lbs (3 kg)
Vibration ....................................... ISTA 1A in carton (International Safe Transit Association)
Listings .......................................... UL, CUL
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
All nominal levels are at 10%.
Specificationsaresubjecttochangewithoutnotice.
IN1502 • Appendix
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix, cont’d
Part Numbers and Accessories
Included parts
These items are included in each order for a IN1502 scaler:
Included parts
Part number
IN1502
60-726-01
Rubber feet (self-adhesive) (4)
IEC power cord
Tweeker (small screwdriver)
IN1502 User’s Manual
Accessories
These items can be ordered separately:
Accessories
Part number
IR 901 remote control
1U Universal rack shelf
1U Basic rack shelf
70-152-01
60-190-01
60-604-01
70-219-01
1U Under-desk mount kit
A-4
IN1502 • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Firmware Upgrade Installation
In some cases, the IN1502’s firmware may require replacement with an updated
version. There are three user-replaceable firmware chips: U41 — the main
microcontroller, U38, and U17. The numbers are printed on the circuit board. We
recommend that you send the unit to Extron for service and updates.
Changes to firmware must be performed by authorized service personnel
only. Some IN1502 firmware updates must be performed at the Extron
factory.
Follow these steps to replace firmware in the scaler.
1.
Disconnect the AC power cord from the IN1502 to remove power from the
unit.
To prevent electric shock or damage, always unplug the IN1502 scaler
from the AC power source before opening the enclosure.
2.
3.
Remove the scaler from the rack or furniture.
Remove the cover of the scaler (the top half of the enclosure) by removing
the four screws, then lifting the cover straight up.
Remove (4)
Lift Cover
Screws from
Straight Up
Top
1
2
M
E
N
U
N
E
X
T
A
D
J
U
S
T
IR
IN
1
S
V
I
5
C
D
E
0
2
E
O
A
L
R
Do not touch any switches or other electronic components inside the
scaler. Doing so could damage the scaler. Electrostatic discharge (ESD)
can damage IC chips even though you cannot feel it. You must be
electrically grounded before proceeding with firmware replacement. A
grounding wrist strap is recommended.
4.
Locate the firmware chip(s) to be replaced on the circuit board, as shown in
the following illustration.
Locating the three firmware IC chips
IN1502 • Appendix
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix, cont’d
U17
U41
U38
5.
After you are electrically grounded, you can remove the U17 IC chip or U38
IC chip by grasping it firmly with your fingers and pulling it out; then
continue to step 8.
Removal of the U41 IC chip requires a PLCC IC puller
tool. To remove the U41 chip, align the hooks of a
PLCC IC puller tool with the slots located in opposite
ends of the U41 firmware chip.
6.
Insert the hooks into the slots, and squeeze the tool
gently to grasp the chip.
7.
8.
Pull the chip straight out of the socket, and set it aside.
For U17 and U38, align the notch of the new firmware
chip with the notch of the socket in the same
orientation as the old chip.
For U41, align the angled
corner of the firmware
Align Notches
chip with the angled
corner of the socket.
U41
9.
Gently, but firmly, press
the chip into place in the
socket.
10. Replace the top cover on the IN1502 scaler, and fasten
it with the screws that were removed in step 3.
11. Rack or furniture mount the scaler, and reconnect the AC power cord.
A-6
IN1502 • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of
three years from the date of purchase. In the event of malfunction during the warranty period
attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option,
repair or replace said products or components, to whatever extent it shall deem necessary to restore
said product to proper operating condition, provided that it is returned within the warranty period,
with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Europe, Africa, and the Middle East:
ExtronElectronics
1001 East Ball Road
Anaheim, CA 92805, USA
Extron Electronics, Europe
Beeldschermweg6C
3821AHAmersfoort
The Netherlands
Asia:
Japan:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Extron Electronics, Japan
KyodoBuilding
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Singapore 368363
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care,
electrical or mechanical abuse, abnormal operating conditions or non-Extron authorized modification
totheproduct.
If it has been determined that the product is defective, please call Extron and ask for an Applications
Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400 (Asia), or 81.3.3511.7655 (Japan)
to receive an RA# (Return Authorization number). This will begin the repair process as quickly as
possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk
of loss or damage during shipment. Returned units must include the serial number and a
description of the problem, as well as the name of the person to contact in case there are any
questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the
product and its quality, performance, merchantability, or fitness for any particular use. In no event
will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any
defect in this product even if Extron Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of
this warranty may not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|