User Guide
TouchLink™
TLP VIM
TouchLink Video Input Module
68-2055-01 Rev. A
03 11
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
The Class A limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required
to correct the interference at his own expense.
NOTE: This unit was tested with shielded cables on the peripheral devices.
Shielded cables must be used with the unit to ensure compliance
with FCC emissions limits.
For more information on safety guidelines, regulatory compliances,
EMI/EMF compliance, accessibility, and related topics.
Notational Conventions Used in this Guide
TIP: A tip provides a suggestion to make setting up or working with
the device easier.
NOTE: A note draws attention to important information.
CAUTION:
WARNING:
A caution warns of things or actions that might damage
the equipment.
A warning warns of things or actions that might cause
injury, death, or other severe consequences.
Copyright
© 2011 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
TLP VIM • Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This section gives an overview of the TLP VIM, TouchLink™ Video
Input Module describing its operation and features including
connection and operation with the Extron line of TouchLink panels.
Topics that are covered include:
z
z
About the TLP VIM
Application Diagrams
About the TLP VIM
The TLP VIM is a twisted pair transmitter for composite or S-video
with audio, designed exclusively for use with compatible Extron
TouchLink touchpanels. The TLP VIM has a very specific application
to these touchpanels and is not intended to be used in other
applications.
Compatible TLP touchpanel products have a single video input
supporting AV signals via an MTP receiver built into the touchpanel.
For installations where the video source is within 100 feet of the
touchpanel, the TLP VIP provides a cost effective solution to transmit
video and audio to the touchpanel.
Due to the limited range, the TLP VIM does not require skew or gain
adjustments.
TLP VIM • Introduction
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Video/Audio
Extron
TLP VIM
P
O
W
E
R
A
U
D
IO
+
-
M
TP
V
O
ID
E
OUTPU
UTPU
O
+
-
T
TLP 1000TV
Video/
Audio
PC or DVD
Extron
12 V Power
Supply
POWER
AUDIO
+
Extron
TLP VIM
-
MTP OUTPUT
VIDEO
+
-
Audio
Video/Audio
(100´ max)
Video
PC or DVD
TLP 1000TV
Figure 1. TLP VIM Application Diagrams
2
TLP VIM • Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and
Operation
This chapter shows how to install and operate the TLP VIM Video
Input Module.
Topics that are covered include:
z
z
z
z
Installation Overview
Mounting the TLP VIM
Installation Overview
To install and set up the TLP VIM, follow these steps:
1. Turn all equipment off. Make sure the video sources (DSS,
cable boxes, PC, laptop, or other devices), the TLP VIM, and the
touchpanel are turned off and disconnected from power sources.
Mounting the TLP VIM
The TLP VIM includes hook and loop fasteners so that it can be
securely mounted on or under a table or podium near to the
touchpanel.
Shut off all power to connected devices, then mount the TLP VIM as
required.
TLP VIM • Installation and Operation
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TLP VIM Front and Rear Panel Features
Front
TLP VIM
a
b
Rear
c
d
e
INPUT
POWER
12V
VIDEO
0.5A MAX
AUDIO
OUTPUT
Figure 2. TLP VIM Front and Rear Panel
Front panel LED ꢀ Single LED lights to indicate the TLP VIM is
properly powered.
a
b
DC power input ꢀ Single 2-pole, 3.5 mm, orange captive screw
connector for connection of a 12 V power supply.
Use only the included power supply or an Extron authorized
power supply to power the TLP VIM.
4
TLP VIM • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT
POWER
12V
VIDEO
0.5A MAX
AUDIO
Smooth
Ridges
Captive
Screw
Connector
A
A
OUTPUT
SECTION A–A
Tie Wrap
Power Supply
Output Cord
DC Power Cord
Captive Screw
Connector
3"
16 (5 mm) Max.
Ground
+12 VDC
External
Power Supply
(12 VDC, 1 A )
AC Power Cord
Figure 3. Power Supply Wiring
CAUTION:
Always use a power supply supplied or specified by Extron. Use
of an unauthorized power supply voids all regulatory compliance
certification and may cause damage to the supply and the
TLP VIM.
Extron power supplies are certified to UL/CSA 60950-1 and
are classified as LPS (limited power source). Use of a non-LPS
or unlisted power supply will void all regulatory compliance
certification.
Unless otherwise stated, the AC/DC adapters are not suitable for
use in air handling spaces or in wall cavities. The power supply is
to be located within the same vicinity as the Extron A/V processing
equipment in an ordinary location, Pollution Degree 2, secured to
the equipment rack within the dedicated closet, podium or desk.
The installation must always be in accordance with the applicable
provisions of National Electrical Code ANSI/NFPA 70, article 75, and
the Canadian Electrical Code, part 1, section 16. The power supply
shall not be permanently fixed to building structure or similar
structure.
Audio input ꢀ One 3-pole captive screw connector for inputting
balanced or unbalanced audio. The audio input is mono only and
either balanced or unbalanced.
c
Tip
Tip
Ring
Sleeve
Sleeve
Unbalanced Input
Balanced Input
Figure 4. Audio Input Connector Wiring
TLP VIM • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Video input ꢀ Two female BNC connectors on pigtails used to
input either S-video (yellow-chroma, white-luma) or composite
video (white only).
d
For composite input, connect the composite cable to the white
video input cable.
12V
0.5A MAX
AUD
For S-video input
connect the luma cable
to the white video
input and the chroma
cable to the yellow
video input.
White: Luma or
Composite
Yellow: Chroma
Figure 5. Video Inputs
MTP output ꢀ One female RJ-45 connector to output the MTP A/V
signal to the touchpanel.
e
The TP cable connecting the TLP VIM output to the MTP input of
the touchpanel is standard UTP or STP Cat 5 or better cable. The
ends may be terminated using either TIA/EIA 568A or TIA/EIA 568B
but both ends must use the same standard.
Pins:
MTP Signal
Composite
MTP Signal
S-video
T568A
T568B
12345678
Pin Wire Color
Wire Color
1
2
3
4
5
6
7
8
White-green White-orange Reserved
Chroma+
Chroma–
Mono audio+
Luma+
Green
Orange
Reserved
Mono audio+
Video+
White-orange White-green
Blue
Blue
White-blue
White-blue
Video–
Luma–
Orange
Green
Mono audio–
Mono audio–
Reserved
Reserved
White-brown White-brown Reserved
Brown Brown Reserved
Insert
TP Wires
NOTE: When using Enhanced Skew-Free™ A/V cable, use
the TIA/EIA T568A standard only.
CAUTION:
The TLP VIM output uses higher voltages than a LAN. Inputting
those voltages on a LAN communications port may damage the
connection.
Operation
No setup or configuration is required. Once cabling is complete,
apply power to the connected equipment and TLP VIM. The unit is
ready for operation.
6
TLP VIM • Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Information
Included Parts
Description
Part Number
TLP VIM
60-1168-01
12 VDC, 1 A power supply
28-071-57LF
10-703-11LF
3-pole blue 3.5 mm male captive screw connector
TLP VIM User Guide
Optional Accessories
Enhanced Skew-Free™ A/V UTP Cable
Skew-Free UTP/3, 3 ft (90 cm)
Part Number
26-569-01
Skew-Free UTP/6, 6 ft (1.8 m)
26-569-02
Skew-Free UTP/12, 12 ft (3.6 m)
26-569-03
Skew-Free UTP/1000, non-plenum, 1000 ft (300 m) 22-141-03
Skew-Free UTP-P/1000, plenum, 1000 ft (300 m) 22-142-03
TLP VIM • References
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Specifications
Video
Gain����������������������������������������������� Unity
Differential phase error������������������� <1�0° at 3�58 MHz and 4�43 MHz
Differential gain error ��������������������� <1�0% at 3�58 MHz and 4�43 MHz
Video input
Number/signal type ������������������������ 1 S-video or composite video
Connectors ������������������������������������ 2 female BNC on pigtails
Nominal level ��������������������������������� 1 Vp-p for Y of S-video and for
composite video
0�3 Vp-p for C of S-video
Minimum/maximum levels�������������� 0�3 V to 1�5 Vp-p with no offset
Impedance ������������������������������������� 75 ohms
Return loss������������������������������������� <-30 dB, DC @ 10 MHz
DC offset (max� allowable) ������������� 100 mV
Video output
Number/signal type ������������������������ 1 set of proprietary analog signals
Connector�������������������������������������� 1 female RJ-45
Nominal level ��������������������������������� 1 V p-p for Y of S-video and for
composite video
0�3 V p-p for C of S-video
Minimum/maximum levels�������������� 0�3 V to 1�5 Vp-p
Impedance ������������������������������������� 75 ohms
Return loss������������������������������������� <-35 dB @ 5 MHz
Sync
Standards��������������������������������������� NTSC 3�58, NTSC 4�43, PAL, SECAM
Audio
Gain����������������������������������������������� 0 dB (unity)
Frequency response������������������������ 20 Hz to 20 kHz, 0�25 dB
THD + Noise����������������������������������� 0�03% @ 1 kHz, 0�3% @ 20 kHz at
nominal level
S/N������������������������������������������������� >90 dB, balanced at maximum output
(unweighted)
CMRR �������������������������������������������� >34 dB @ 20 Hz to 20 kHz
8
TLP VIM • References
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio input
Number/signal type ������������������������ 1 mono, balanced or unbalanced
Connector�������������������������������������� (1) 3�5 mm captive screw connector,
3 pole
Impedance ������������������������������������� >10k ohms unbalanced, >20k ohms
balanced, AC coupled
Nominal level ��������������������������������� -10 dBV (0�32 Vrms)
Maximum level������������������������������� >+2�4 dBu (balanced or unbalanced) at
1%THD+N
NOTE: 0 dBu = 0�775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
Number/signal type ������������������������ 1 set of proprietary analog signals
Connector�������������������������������������� 1 female RJ-45
Impedance ������������������������������������� 50 ohms unbalanced, 100 ohms
balanced
Maximum level (Hi-Z)���������������������� >+3�3 dBu, balanced or unbalanced at
1%THD+N
Maximum level (600 ohm)�������������� >+2�0 dBm, balanced or unbalanced at
1%THD+N
General
Recommended cable type �������������� CAT5/5e/6 (shielded or unshielded)
External power supply�������������������� Input: 100 VAC to 240 VAC, 50-60 Hz,
external power supply
Output: 12 VDC, 1�0 A, regulated
Power input requirements �������������� 12 VDC, 0�5 A max�
Temperature/humidity �������������������� Storage: -40 to +158 °F (-40 to +70 °C)
/ 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C)
/ 10% to 90%, noncondensing
Cooling������������������������������������������ Convection, no vents
Mounting��������������������������������������� Tabletop
Enclosure type�������������������������������� Plastic
Enclosure dimensions ��������������������� 1�0" H x 2�4" W x 2�3" D
(2�5 cm H x 6�1 cm W x 5�8 cm D)
(Depth excludes pigtail connectors�)
Product weight������������������������������� 0�2 lbs (0�1 kg)
Shipping weight����������������������������� 1 lb (1 kg)
Vibration���������������������������������������� ISTA 1A in carton (International Safe
Transit Association)
TLP VIM • References
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Regulatory compliance
Safety�������������������������������������� CE, c-UL, UL
EMI/EMC ��������������������������������� CE, C-tick, FCC Class A, ICES, VCCI
MTBF ��������������������������������������������� 30,000 hours
Warranty���������������������������������������� 3 years parts and labor
NOTE: All nominal levels are at 10%�
10 TLP VIM • References
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron® Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction
during the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components, to
whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the
Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia
Middle East:
Extron Middle East
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions, or if
modifications were made to the product that were not authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an application
engineer to receive an RA (return authorization) number. This will begin
the repair process.
USA:
Asia:
(714) 491-1500
65.6383.4400
Europe: 31.33.453.4040
Japan: 81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with
respect to the product and its quality, performance, merchantability, or fitness for
any particular use. In no event will Extron Electronics be liable for direct, indirect,
or consequential damages resulting from any defect in this product even if Extron
Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
+800.633.9876
Inside USA/Canada
Only
+1.714.491.1500
+1.714.491.1517 FAX
Download from Www.Somanuals.com. All Manuals Search And Download.
|
