Extron electronic Switch BB 710M User Manual

Product Category  
BB 710M • Installation Guide  
Overview  
The Extron BB 710M back box is used to mount an Extron TLP 710MV TouchLinkpanel in a wall. This Installation Guide  
provides instructions for an experienced installer to retrofit the box in existing drywall or mount the back box in a new  
installation. For complete instructions about installing and calibrating the TouchLink panel, see the TLP 710MV and  
TLP 710TV User Guide, which are available on the Extron web site (www.extron.com).  
Retrofit an Existing Installation (with the Drywall in Place)  
1. Separate and remove the endplates (top and bottom) from the U-plate (sides and  
back).  
2. Use the back face of the U-plate to mark the position where the hole will be cut. Use a  
7
level to ensure the U-plate is level.  
NOTE: The hole is 7.7 inches (19.5 cm) wide x 6 inches (15.1 cm) high.  
3. Using a drywall saw, carefully cut a hole where the touchpanel will be installed. Cut on  
BB 710M  
U-plate  
the lines that you marked in step 2.  
4. Run the cable conduit through the wall. The conduit can be attached to any of the  
available knock-out holes in the top, bottom, or either side. Leave some slack to  
connect the conduit to the back box and the cables to the touchpanel.  
Tabs (4)  
Figure 1.  
5. Run cables to the installation site.  
6. Clear the cables and conduits from the space behind the hole.  
9
7. If required, secure a conduit to the U-plate and insert the U-plate  
into the hole (see figure 1).  
NOTE: The U-plate tabs sit on the outer face of the drywall.  
10  
8. Pull back the cables that were cleared out of the way in step 5.  
9. If required, secure one or more conduits to the knock-out holes in  
the endplate (see figure 2). Break off the lip on the leading edge  
of the endplate (see figure 3) to make it easier to maneuver the  
Figure 2.  
endplate with a conduit attached.  
10. Slide the endplates into the gap between the back of the U-plate  
and the top flanges on the side of the U-plate (see the inset in  
figure 2). The endplate must pass the drywall so that the trailing  
edge can be pushed in behind it.  
Tabs are against  
outside surface  
of drywall.  
11. Secure the endplate to the U-plate, using the four provided  
screws. Insert the provided screw from inside the BB 710M,  
through the slot in the endplate and into the threaded hole in  
the top of the U-plate (see figure 3).  
The endplates (behind) and the tabs of the U-plate (in front)  
clamp the drywall, holding the BB 710M securely in place.  
12. Finish installing the  
TouchLink panel  
as shown in figure  
4 and described  
in “Mounting the  
Touchpanel” on the  
next page.  
Lip Snaps  
Off  
Slot  
Tighten screws to  
rotate locking arms.  
Threaded  
Hole  
Bezel snaps to unit  
(4 places on each side).  
Figure 3.  
Figure 4.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edimax Technology Network Router BR 6228NC V2 User Manual
Estate Range W10017740 User Manual
Everpure Water System EV9100 66 User Manual
Field Controls Air Cleaner UV 16 24 User Manual
First Alert Home Security System FA142C User Manual
FMI Indoor Fireplace M36EBH User Manual
Fusionbrands Pet Fence fm 504 User Manual
Gateway Computer Monitor FHX2300 User Manual
GE Coffeemaker 169184 User Manual
GE Monogram Garage Door Opener RM94925 User Manual