User’s Manual
DVI DL 101
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Dual Length DVI Cable Equalizer
68-1574-01 Rev. A
+81.3.3511.7655 FAX +81.3.3511.7656
06 08
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
这个符号提示用户该设备用户手册中
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线
（ 地 线 ） 是 安 全 设 施 ， 不 能 不 用 或 跳 过 。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解 所 有 安 全 和 使 用 说 明 。
保存说明书 • 用户应保存安全说明书以备将来使
用。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
N
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Featuꢀes ........................................................................................ 1-2
Accessories ........................................................................................A-1
All trademarks mentioned in this manual are the properties of their respective owners.
68-1574-01 Rev. A
07 08
DVI DL 101 • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
• DVI output — One female DVI-I connector supports DVI-D
output.
The acceptable output cable length is 16.4' (5 m).
About this Manual
This manual contains information about the Extron DVI DL 101
Dual Link Cable Equalizer and describes how to connect
and operate it. The terms "DVI DL" and "equalizer" are used
interchangeably throughout this manual to refer to the product.
Dual link DVI cables must be used for dual link DVI
signals. With a single link DVI cable, only single-link
signals are possible.
N
About the DVI DL 101 Cable Equalizer
• Rack and furniture mounting — The equalizer can be
mounted on a rack shelf, or under or through a desk or
podium.
• Power supply — An external international power supply with
a two-pin captive screw connector accepts 100 to 240 VAC.
The Extron DVI DL 101 is a dual link cable equalizer that
extends Digital Visual Interface (DVI) signals beyond the
specified cable limits of 15' (5 m). The DVI DL attaches to the
end of a long cable run of up to 275' (84 m) for dual link and up
to 200' (61 m) for single link.
Placed just before the display in the cable run, it automatically
equalizes and drives the signal, eliminating any noise or
dropouts, to ensure optimal image quality. It supports all dual
link DVI signals up to 330 MHz, including 2560x1600 @ 60 Hz.
Also, because dual link is backwards compatible with single
link, all single link rates up to 165 MHz, including 1920x1200
and 1080p @ 60 Hz, are also supported.
Application Diagrams
The following diagrams show examples of how the DVI DL can
be connected.
200' DVI Dual
Link Cable
1
0
1
VI DL
D
The DVI DL passes Extended Display Identification Data (EDID)
information and supports the long distance transmission of
HDTV signals with High-bandwidth Digital Content Protection
(HDCP) for copy protection of digital television broadcasts and
high resolution digital video output from DVD, HD DVD, and
Blu-ray Disc players. DDC lines are passed through with the
option of active buffering to ensure compatibility among various
source and display configurations.
VI-D O
D
R
WE
PO
1
X
V
A
2
0.2A
M
Extron
DVI DL 101
DVI Dual Link
Equalizer
15' DVI Dual
Link Cable
PC
With the appropriate adapters from Extron, the DVI DL is fully
compatible with the HDMI digital video, audio, and control
standard for audio/video products.
Hi Resolution
Projector w/ Dual Link
Input
Features
DVI DL application diagram
• Power/Signal status indicator — The LED on the front panel
lights amber to indicate that power is connected. When a
source signal is present, this LED lights green.
• Optional buffering of DDC/HDCP lines — DDC/HDCP
clock and data lines can be actively buffered or passed
straight through to the output.
• Enclosure — Compact 1" (2.5 cm) high, ¼ rack wide metal
enclosure
• DVI input — One DVI-I female connector accepts a DVI-D
input signal and supports dual link rates of up to 330 MHz, as
well as all single link rates up to 165 MHz.
The maximum length for input cables is 200' (50.8 m) for the
highest rates (330 MHz for dual link; 135 MHz for single link).
DVI DL 101 • Intꢀoduction
DVI DL 101 • Intꢀoduction
1-2
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (such as the use of power
strips).
Mounting the DVI DL 101
The DVI DL can be mounted on a rack shelf, under or through
furniture, attached to a projector pole, or placed on a table top.
Tabletop use
Rack mounting procedure
Four self-adhesive rubber feet are included with the DVI DL.
For tabletop use, attach one foot at each corner on the bottom
surface of the unit.
On the 6" deep and 9.5" deep rack shelves, the unit can be
mounted in the front or the rear of the rack.
1.
2.
3.
4.
5.
If rubber feet were previously installed on the bottom of
the unit, remove them.
Rack mounting
The optional accessories available for rack mounting the DVI DL
include the following:
Secure the DVI DL on the rack shelf, using two 4-40 x
3/16" screws in opposite (diagonal) corners.
•
RSF 123 — 3.5" deep 1U VersaTools® rack shelf kit
(part #60-190-20)
Install blank panel(s) or other unit(s) on the rack shelf as
desired.
•
•
RSB123—3.5"deep1UVersaToolsrackshelf(part#60-604-20)
Insert the shelf into the rack, aligning the holes in the shelf
with those of the rack.
RSU 126 — 6" deep 1U universal rack shelf kit
(part #60-190-10)
Secure the shelf to the rack using the supplied machine
screws. This shelf can be mounted in the front or in the
rear of the rack.
•
•
RSB 126 — 6" deep 1U basic rack shelf (part #60-604-10)
RSU 129 — 9.5" deep 1U universal rack shelf kit
(part #60-190-01)
1U Universal Rack Shelf
•
RSB 129 — 9.5" deep 1U basic rack shelf (part #60-604-01)
UL rack mounting guidelines
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the DVI DL 101 into or onto a rack.
1.
Elevated operating ambient — If the equipment is
installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment
may be greater than room ambient. Therefore, consider
installing the equipment in an environment compatible
with the +122 °F (+50 °C) maximum ambient temperature
(Tma) specified by Extron.
2.
3.
4.
Reduced air flow — Install the equipment in the rack so
that the amount of air flow required for safe operation of
the equipment is not compromised.
(2) 4-40 x 3/16"
Screws
Mechanical loading — Mount the equipment in the rack
so that uneven mechanical loading does not lead to a
hazardous condition.
Use 2 mounting holes on
opposite corners.
Mounting the DVI DL 100 on a standard rack shelf
Circuit overloading — When connecting the equipment
to the supply circuit, consider the connection of the
equipment to the supply circuit and the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Consider equipment nameplate ratings
when addressing this concern.
DVI DL 101 • Installation and Opeꢀation
DVI DL 101• Installation and Opeꢀation
2-2
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
VersaTools Rack Shelf
1/4 Rack Width Front
False Faceplate
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Under-furniture mounting the DVI DL
6.
7.
8.
9.
Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)
deep in the mounting surface at the marked screw
locations.
Mounting the DVI DL 101 on a 3.5” deep rack shelf
Under-furniture mounting
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until slightly less
than 1/4" of the screw head protrudes.
The DVI DL can be mounted under a horizontal surface using an
optional MBU 125 under-desk mounting kit (part #70-077-01), as
follows:
Align the mounting screws with the slots in the brackets
and place the unit against the surface, with the screws
through the bracket slots.
1.
2.
3.
If rubber feet were previously attached to the bottom of the
unit, remove them.
Remove the screws from one side of the unit. Retain the
screws for possible later reassembly.
Slide the unit slightly forward or back, then tighten all four
screws to secure it in place.
Attach one bracket to the side of the unit, using the
provided machine screws (see the illustration on the next
page).
Through-furniture mounting
The DVI DL can be mounted through a desk or other furniture
using an optional Extron MBD 129 through-desk mounting kit
(part #70-077-02) as follows:
4.
5.
Repeat steps 2 and 3 on the other side of the DVI DL.
Hold the unit with the attached brackets against the
underside of the table or other furniture. On the mounting
surface, mark the location of the bracket’s screw holes.
1.
Loosely attach the mounting brackets to the unit using
the four machine screws and washers supplied with the
mounting kit.
2.
Hold the unit against the inside of the surface through
which it will be mounted. Mark the four screw holes on
the inside of the surface to which you are mounting the
device.
3.
Cut out the material from the installation area with a
jigsaw.
DVI DL 101 • Installation and Opeꢀation
DVI DL 101 • Installation and Opeꢀation
2-4
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
PMK 300 mounting
Mount the DVI DL to a PMK 300 bracket as follows:
1.
2.
If necessary, remove the feet from the bottom of the unit.
Mount the receiver to one of the bracket’s three mounting
plates using two of the supplied 4-40 x 3/16" screws in
opposite (diagonal) corners to secure the device to the
bracket. It can be vertically mounted facing either up or
down (see the illustration below).
On the side mounting plates, the device is typically
mounted on the outside of the bracket.
N
On the front mounting plate, the device is typically
mounted on the inside of the bracket.
Side Mounting
Plate
Bracket
Brace
U-Bolt
Extron
DVI DL 101
Equalizer
Through-desk mounting the DVI DL
4.
5.
6.
Drill four pilot holes, each 3/32" in diameter by 1/4" deep,
where you made marks.
Power Supply
Using the provided four wood screws, secure the brackets
to the mounting surface.
Extron
PMK 300
Multi-product Projector Mount Kit
Slide the DVI DL up and down in the mounting brackets
until the front panel is at the desired height. Tighten the
screws that secure the brackets in place.
Front Mounting
Plate
If the screws are inaccessible to a screwdriver:
a. Mark the location of the brackets relative to the screws.
b. Remove the unit from inside the furniture.
c. Tighten the screws.
d. Replace the unit inside the surface (step 4).
Projector mounting
PMK 300 projector mounting a receiver
The DVI DL can be mounted on a projector bracket using either
of the following optional Extron projector mounting kits:
3.
Strap the power supply to one of the brackets, using the
two included tie wraps.
•
•
PMK 300 projector mounting kit (part #70-374-01)
The PMK 300 has a hole in the bottom plate that allows
the projector pole to be inserted through the center of
the plate, rather than outside of the plate). To install the
PMK 300 in this configuration, slide the bracket up from
the bottom of the pole before the projector is installed on
the pole.
N
PMK 350 low profile projector mounting kit
(part #70-563-02 [black] or part #70-563-03 [white])
DVI DL 101 • Installation and Opeꢀation
DVI DL 101 • Installation and Opeꢀation
2-6
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
6.
Secure the bracket to the U-bolt with the included hex
nuts, washers, and lock washers. Tighten the hex nuts just
enough that they can be loosened by hand.
Contoured
Bracket
Base
PMK 350 mounting
Extron
Mount the DVI DL to a PMK 350 bracket as follows:
DVI DL 101
1.
Remove the front and rear plates from the PMK 350, using
an Extron Tweeker or a #2 Philips screwdriver. Retain the
screws to reattach the plates when you are finished.
Equalizer
Power Supply
2.
3.
If necessary, remove the feet from the bottom of the unit.
Secure the DVI DL to one side of the mounting tray,
using two of the supplied 4-40 x 3/16” screws in opposite
(diagonal) corners.
Extron
PMK 300
Multi-product Projector
Mount Kit
U-bolt
Extron
DVI DL 101
Equalizer
Rear Plate
Contoured
Base
L-shaped
Bracket
Extron
PMK 350
Multi-product Projector
Mounting Kit
U-bolt
Extron
Power Supply
Front Plate
Cover Sheet
Mounting with the projector pole on the inside
PMK 350 projector mounting a DVI DL
4.
Place the contoured bracket brace against the pole and
opposite the back plate. The pole should fit snugly into the
depression in the center of the bracket brace.
4.
5.
Using the two included tie wraps, strap the power supply
to the PMK bracket.
5.
Place the U-bolt around the ceiling pole. Insert the
two legs of the U-bolt through the round holes on the
contoured bracket brace and then through the slotted holes
on the bracket’s mounting plate.
If desired, remove the back panel of the PMK 350 and
mount additional device(s) at the back of the bracket, as
described in step 3.
6.
Place the PMK 350 around the projector ceiling mounting
pole.
The supplied U-bolt fits a typical (1.5" to 2.0" diameter)
ceiling pole.
N
DVI DL 101 • Installation and Opeꢀation
DVI DL 101 • Installation and Opeꢀation
2-8
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
7.
Assemble the U-bolt and the following parts in the
following order (see the illustration below):
Front and Back Panel Features and Connections
2
a. Pass the legs of the U-bolt through the slotted holes on
the mount plate flange.
DVI-DUAL LINK INPUT
b. Place the legs around the projector pole.
1
c. Pass the legs through the holes in the contour base.
DVI DL 101
The pole fits snugly into the depression in the
center of the contoured base.
N
d. Pass the legs through the holes in the L-shaped bracket.
DVI DL 101
POWER
The supplied U-bolt fits a typical (1.5" to 2.0"
diameter) ceiling pole.
N
DVI-DUAL LINK OUTPUT
12V
0.2A MAX
4
Mount Plate
Flange
Contoured
Base
U-bolt
3
L-shaped
Bracket
DVI DL front and rear panels
Slotted Hole
in PMK Tray
L-shaped
Bracket Screws
Status LED — This dual-color LED lights amber when the
DVI DL is receiving power. When a DVI input signal is present,
this LED lights green.
a
b
Ceiling
Pole
DVI input connector — Plug the cable from the input source
device into this dual link female DVI-I connector. Dual link
rates of up to 2560x1600 @ 60 Hz and single link rates of up to
1920x1200 and 1080p @ 60 Hz are supported. The table on the
next page shows the DVI pin configuration.
Figure 2-8 — Hanging the PMK 350 tray on the
projector pole
8.
Align the two holes in the bottom of the L-shaped bracket
with the two holes in the base of the tray. Secure the
L-bracket to the base by inserting two of the provided
6-32 x 5/16" screws through the aligned slots.
Dual link DVI cables must be used for dual link DVI
signals. If a single link DVI cable is used, only single
link DVI signals are possible.
N
9.
Move the PMK 350 up to the desired location on the ceiling
pole, as close to the ceiling as desired.
10. Secure the L-shaped bracket to the U-bolt using the
included hex nuts, washers, and lock washers. Tighten the
hex nuts securely.
Be sure to tighten the hex nuts securely enough that the
PMK 350 does not slide down the ceiling pole. A socket
wrench is recommended to tighten the hex nuts.
N
11. Secure the front and rear plates to the mounting tray with
four of the included #6 screws.
12. If desired, choose one of the provided four sizes of self-
adhesive cover sheets, and apply it to the underside of the
mounting tray.
DVI DL 101 • Installation and Opeꢀation
DVI DL 101 • Installation and Opeꢀation
2-10
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
1
8
The table below shows the maximum cable lengths
recommended for each resolution, in dual link mode and single
link mode.
9
17
24
Avoid using couplers and adapters between cables, as
this can result in signal degradation.
N
Pin
Pin
Signal
Signal
Pin
Signal
Video
Single Link
Mode
Dual Link
Mode
1
TMDS data 2–
9
TMDS data 1– 17 TMDS data 0–
Resolution
2
3
TMDS data 2+ 10 TMDS data 1+ 18 TMDS data 0+
1280x1024
1024x768
720p
TMDS data
2/4 shield
11 TMDS data 1
shield
19 TMDS data 0/5
shield
250'
275'
(76 m)
(84 m)
4
5
6
TMDS data 4– 12 TMDS data 3– 20 TMDS data 5–
TMDS data 4+ 13 TMDS data 3+ 21 TMDS data 5+
1080i
1920x1200
1600x1200
1080p
200'
250'
DDC clock
14 +5 V power
22 TMDS clock
shield
(61 m)
(76 m)
7
8
DDC data
15 Ground (+5 V) 23 TMDS clock+
200'
2560x1600
N/A
(61 m)
CEC control* 16 Hot plug
detector
24 TMDS clock–
DVI output connector — Plug the cable from a DVI output
device into this female dual link DVI-I connector, following
the pin configuration shown in the table on page 2-12. Output
signals will be digital only. The maximum output cable length is
16.4' (5 m). Pin 14 provides +5 VDC power.
* CEC control on pin 8 is a proprietary usage, and is not the
industry standard.
c
d
DVI connector pin assignments
Dual link DVI cables must be used for dual link DVI
signals. If a single link DVI cable is used, only single
link DVI signals are possible.
N
Input cable lengths
To obtain the highest transmission rate of 330 MHz (dual link) or
165 MHz (single link), the maximum input cable length for the
DVI DL 101 is 200' (61 m). Longer cables may be used at lower
rates. High quality cable can increase the distance and rate of
transmission. However, the achievable distance and speed are
also contingent on the sensitivity of the input source and the
display device.
Power connector — Plug the external 12 V power supply
(provided with the unit) into this 2-pole captive screw connector.
The figure on the next page shows how to wire the connector.
Dual and single link modes
The DVI DL 101 can operate in dual link mode or single link
mode; dual link DVI is backwards compatible with single link
DVI.
Operation in dual link mode requires that both the source
and the display support dual link DVI signals. If they
do not, the DVI DL 101 can operate in only single link
mode.
N
DVI DL 101 • Installation and Opeꢀation
DVI DL 101 • Installation and Opeꢀation
2-12
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
• Incorrect color space selection (purple or blue tint)
• Corrupted EDID data (The computer or source cannot read
the EDID of the connected display correctly due to a long
cable run.)
Smooth
Ridges
A
A
SECTION A–A
To enable the buffer,
1.
Using an Extron Tweeker or other small Philips
screwdriver, remove the seven screws (three on each side
and one on top) that hold the top cover onto the unit.
Power Supply
Output Cord
Tie Wrap
2.
Remove the two jack screws on either side of the DVI input
connector on the front panel (see the illustration on the
next page).
3/16” (5 mm) Max.
3.
4.
Slide the top cover forward until it clears the input
connector, then lift it off the unit.
Orange Captive Screw
Connector
Facing the DVI DL rear panel, locate the two DDC jumpers
(J5 and J4) on the two sets of three pins in the lower-right
corner of the internal board. By default, these jumpers are
on the middle and outside pins, which permits the DDC
lines to pass straight through without buffering.
Wiring the power connector
When you are connecting the power supply, voltage
polarity is extremely important. Applying power
with incorrect voltage polarity could damage
the power supply and the equalizer. Identify the
negative lead by the ridges on the side of the cord
(see the illustration above).
C
Do not tin the stripped power supply leads before
installing the captive screw connector. Tinned
wires are not as secure in the captive screw
connectors and could be pulled out.
C
W
The two power cord wires must be kept separate
while the power supply is plugged in. Remove
power before continuing.
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
Enabling the DDC Buffer
The DDC clock and data lines by default are routed straight
through to the output, bypassing the DDC buffer.
Jumpers on the internal board in default (outside)
position
However, if you experience any of the following image
problems, changing this setting to engage the DDC buffer
should correct them.
• The image cuts in and out, or cuts out completely, after a
period of time.
• The image is clear at first, then displays snow (HDCP error).
• No image appears.
DVI DL 101 • Installation and Opeꢀation
DVI DL 101 • Installation and Opeꢀation
2-14
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
5.
Lift each jumper off its pins and slide it down onto the
inside and middle pins. See the illustration below.
DVI DL 101
DDC Buffer
Bypassed
(Default)
DDC Buffer
Enabled
Jumper Pin Sets J4 and
J5 Inside Unit
T
U
DVI DL 101
Appendix A
DVI-DU
Slide forward,
then up.
A
Jack Screw
Nut
Remove screws from
sides and top (7).
6.
7.
Replace the top cover onto the unit, and slide it back until
the DVI input connector protrudes through its slot in the
front panel.
Specifications, Parts, and
Accessories
Replace the two jack screws and the seven Philips screws
that you removed in step 1.
Specifications
Included Parts
Optional Accessories
Cables and Adapters
DVI DL 101 • Installation and Opeꢀation
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Parts, and Accessories
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Specifications – DVI DL
*Dual link DVI is backwards compatible with all single link
DVI and HDMI signals.
N
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling ........................................... Convection, no vents
Rack mount.................................... Yes, with optional 1U, 9.5" deep rack shelf,
part #60-190-01 (RSU 129) or #60-604-01
(RSB 129 ); 1U, 6" deep rack shelf,
Video
Maximum data rate....................... 10 Gbps total (3.3 Gbps per color)
Maximum pixel clock ................... 330 MHz (165 MHz per link)
Impedance...................................... 100 ohms
part #60-190-10 (RSU 126) or #60-604-10
(RSB 126); or 3.5" deep VersaTools®
Resolution range ........................... Dual link: Up to 2560x1500 @ 60 Hz
rack shelf, part #60-190-20 (RSF 123) or
#60-604-20 (RSB 123)
Also furniture-mountable with optional
under-desk mounting kit, part #70-077-01
(MBU 125) and through-desk mounting kit,
part #70-077-02 (MBD 129)
Single link: Up to 1920x1200 or 1080p @
60 Hz
Formats........................................... RGB or YCbCr digital video
Standard ......................................... DVI 1.0, HDMI 1.2
Enclosure type ............................... Metal
Enclosure dimensions................... 1.0" H x 4.3" W x 3.0" D (1/4 rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.)
Product weight .............................. 0.5 lbs (0.3 kg)
Shipping weight ........................... 3 lbs (2 kg)
Vibration ........................................ ISTA 1A in carton
(International Safe Transit Association)
Regulatory compliance
Safety................................... CE, UL, CUL, C-tick
Compliances....................... CE, FCC Class A, VCCI, C-tick, ICES
MTBF............................................... 30,000 hours
Warranty ........................................ 3 years parts and labor
Video input
Number/signal type..................... 1 dual link DVI-D*
Connectors ..................................... 1 female DVI-I
Nominal level
Digital video ...................... 1.2 Vp-p (for TMDS)
DDC..................................... TTL: 5 Vp-p
Input cable length ......................... Up to 200' (61 m) at 2560x1600 or 1080p @
60 Hz
Longer distances are possible with lower
rates and/or high quality cable.
The transmission distance varies greatly depending on the signal
resolution and on the type of cable, graphic card, and display
used in the system.
N
All nominal levels are at 10%.
N
N
Equalization................................... Automatic for up to -40 dB of cable loss
Specifications are subject to change without notice.
Video output
Number/signal type..................... 1 dual link DVI-D
Connectors ..................................... 1 female DVI-I
Resolution range ........................... Up to 1920x1200 or 1080p @ 60 Hz
Output cable length ...................... Up to 16.4' (5 m)
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external;
to 12 VDC, 1 A, regulated
Power input requirements........... 12 VDC, 0.2 A from an external power
supply
DVI DL 101 • Specifications, Paꢀts, and Accessoꢀies
DVI DL 101 • Specifications, Paꢀts, and Accessoꢀies
A-2
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Parts, and Accessories, cont’d
Included Parts
Cables and Adapters
These items are included in each order for the DVI DL 101:
The following cables and adapters may be purchased for use
with the DVI DL 101:
Replacement
Included parts
part number
Cable/Adapter
Part number
DVI DL 101 Multi-Rate Equalizer
12 VDC, 2 A external power supply kit
IEC power cord
60-962-01
IN9700 Series DVI (25', 35', 50', and 75'
lengths)
26-584-xx
70-055-01
DVID SL Series DVI (3', 6', and 15' lengths)
26-585-xx
26-614-xx
HDMI M-DVI-D M Series DVI to HDMI
(3', 6', 12', 25', 35', and 50' lengths)
Rubber feet, 4, unattached
Tweeker (small screwdriver)
DVI DL 101 User’s Manual
HDMI M-M Series HDMI (3', 6', 12', 25',
35', and 50' lengths)
26-613-xx
26-617-01
26-616-01
26-618-01
HDMIM-DVIDF HDMI male to DVI-D
female adapter
Optional Accessories
The following items are optional and can be purchased
separately for the DVI DL 101:
HDMIM-DVIDM HDMI female to DVI-D
male adapter
HDMIF-DVIDF HDMI female to DVI-D
female adapter
Accessories
Part number
MBD 129 Through-desk Mount Kit
MBU 125 Under-desk Mount Kit
70-077-02
70-077-01
60-190-01
RSU 129 1U, 9.5" deep, universal rack shelf
kit
RSB 129 1U, 9.5" deep, basic rack shelf
60-604-01
60-190-10
RSU 126 1U, 6" deep, universal rack shelf
kit
RSB 126 1U, 6" deep, basic rack shelf
RSF 123 1U, 3.5" deep, VersaTools® rack
shelf kit
60-604-10
60-190-20
RSB 123 1U, 3.5" deep, basic VersaTools
rack shelf
60-604-20
DVI DL 101 • Specifications, Paꢀts, and Accessoꢀies
DVI DL 101 • Specifications, Paꢀts, and Accessoꢀies
A-4
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Parts, and Accessories, cont’d
This page was intentionally left blank.
DVI DL 101 • Specifications, Paꢀts, and Accessoꢀies
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
|