User’s Manual
P/2 DA2 WM F, WM EC F,
P/2 DA2 D, and AAP models
Distribution Amplifiers
68-463-02 Rev. C
09 08
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 • Introduction ......................................................... 1-1
About the P/2 DA2 WM F/EC F, AAP and
D Models ....................................................................................1-2
Features......................................................................................1-2
Chapter 2 • Controls and Installation ........................... 2-1
Front and Rear Panels ................................................. 2-2
Front faceplate ......................................................................2-2
P/2 DA2 WM F/EC F rear panel ..............................................2-4
P/2 DA2 D rear panel.............................................................2-5
Installing the P/2 DA2 WM F/EC F............................. 2-7
Easy setup procedure ............................................................2-7
Installing the mud ring bracket ............................................. 2-8
Cabling ..................................................................................2-10
Connecting audio output .....................................................2-11
Installing architectural adapter plates ...............................2-12
P/2 DA2 WM F wall mount installation ...............................2-14
P/2 DA2 WM EC F Euro Channel installation ......................2-15
Setting the DIP switches ......................................................2-15
Setting the internal jumpers ...............................................2-16
Installing the P/2 DA2 D ........................................... 2-17
Preparing the site and installing the wall box....................2-17
Mounting the distribution amplifier ...................................2-18
Replacing the faceplate .......................................................2-20
P/2 DA2 D application example ..........................................2-20
Appendix • Specifications, Dimensions, Parts, and
Templates............................................................................................ A-1
Specifications ......................................................................... A-2
Dimensions .............................................................................. A-7
P/2 DA2 WM F faceplate dimensions ................................... A-7
P/2 DA2 WM F AAP faceplate dimensions .......................... A-8
P/2 DA2 D faceplate dimensions.......................................... A-9
Part and Accessories ......................................................... A-10
Included parts...................................................................... A-10
Cables .................................................................................. A-10
Mud ring mounting brackets.............................................. A-10
Optional architectural adapter plates ............................... A-11
P/2 DA2 WM/EC/D/AAP Series • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
Templates ............................................................................... A-15
P/2 DA2 WM F mounting template ................................... A-15
P/2 DA2 WM F AAP mounting template ........................... A-16
P/2 DA2 D mounting template .......................................... A-17
P/2 DA2 WM/EC/D/AAP Series
Chapter One
1
Introduction
About the P/2 DA2 WM F/ EC F, AAP, and D Models
Features
All trademarks mentioned in this manual are the properties of their
respective owners.
68-463-02 Rev. C
09 08
ii
P/2 DA2 WM/EC/D/AAP Series • Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About the P/2 DA2 WM F/EC F, AAP, and D
Models
P/2 DA2 WM/EC/D/AAP Series
The P/2 DA2 WM F/F EC, AAP, and D models are one input,
two output, high resolution VGA/XGA distribution amplifiers
with audio. With a video bandwidth of 300 MHz, these
distribution amplifiers are compatible with VGA, SVGA, VESA,
XGA, and SXGA graphics cards, monitors, projectors, and LCD
panels. The D model features Decora® faceplates and trim.
For audio, the P/2 DA2 WM F/EC F and D feature a 3.5 mm
female jack for input and a 3.5 mm captive screw connector for
balanced or unbalanced output. The D model features a DIP
switch for selecting stereo or dual mono output.
The P/2 DA2 WM F is the wallmount version and the
P/2 DA2 WM EC F is the Euro Channel version. The
P/2 DA2 WM F AAP and the P/2 DA2 WM EC F AAP are the
same base products, but with AAP faceplates added. These
plates are a convenient method of providing various
connectors for most audio and video applications.
Chapter Two
Features
2-color power/signal LED — When the interface is on, the
power/signal LED lights amber. When the interface is on
and a signal is present, the LED lights green.
2
Gain/peak control— Compensates for signal degradation
caused by long cable lengths.
Stereo audio — Front panel audio input jack and a 3.5 mm
Controls and Installation
captive screw output connector on the rear panel.
Buffered local monitor output — 15-pin HD female connector
Computer video input — 15-pin HD female connector
Front and Rear Panels
Installing the P/2 DA2 WM F/EC F
Installing the P/2 DA2 D
Wall mountable (WM model) — Self-contained enclosure
provides for convenient wall mounting.
Euro Channel mountable (EC model) — This model mounts
easily in the Euro Channel raceway
Optional architectural adapter plates — The
P/2 DA2 WM F AAP may be user-configured with up to
four Architectural Adapter Plates (three for the EC AAP
version). These adapter plates provide a selection of
pass-through signal connectors for various audio and
video requirements.
1-2
P/2 DA2 WM/EC/D/AAP Series • Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Installation
Unity – output signal level is same as that of input with no added
Front and Rear Panels
peaking
Front faceplate
50% – increases the output signal level and adds 50% of the maximum
peaking to the signal
N
If the edges of the image seem to exceed their boundaries,
or if thin lines and sharp edges look thick and fuzzy, try
changing the level/peak setting.
AUTO POWER
1
2
1
2
P/2 DA2 WM F EC
AUTO POWER
100%
5
UNITY
6
50%
GAIN/
PEAKING
ID PINS
GAIN/PEAKING
5
6
4
3
4
3
P/2DA2WMFfaceplatefeatures
P/2DA2WMECFfaceplatefeatures
N
Both WM F and WM EC F models have the same front
and rear panel connectors and features.
2-color power/signal LED — lights amber to indicate power on
only; lights green to indicate power on with video signal
present.
1
Audio input jack — 3.5 mm stereo input
2
3
AUDIO IN
1
2
VGA input connector — HD 15-pin female analog video input
connector
COMPUTER IN
MONITOR OUT
3
Buffered local monitor output — HD 15-pin female for output
to a local monitor
4
5
4
ID bit termination DIP switches — provides proper ID bit
termination for a laptop computer that is not attached to a local
monitor. See “Setting the DIP switches” in this chapter.
3-position gain/peaking switch — compensates for cable
capacitance and resistance due to long cable runs; position
switch for best image on the output display device.
6
P/2DA2Dfaceplatefeatures
100% – increases the output signal level and adds 100% of the
maximum peaking to the signal
2-2
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-3
Controls and Installation, cont’d
P/2 DA2 WM F/EC F rear panel
P/2 DA2 D rear panel
1
2
NC
12-24V AC/DC
L
R
1
2
5
NORM
MED
NC
3
HIGH
12-24V AC/DC
L
R
4
3
P/2 DA2 WM F/EC F rear connectors
Figure 2-5 — P/2 DA2 D rear connectors
N
Both WM F and WM EC F models have the same rear
panel connectors.
Configuration DIP switches — The three DIP switches (plus
one spare) configure the P/2 DA2 D, as shown in the table
below.
1
Power input — 12 - 24 VAC or DC (captive screw connector).
The center pole contains no conductor. Connect the conductors
to the outer two poles only.
1
N
The default DIP switch positions are set to On (up).
Set these switches before installing the distribution
amplifier in a wall.
3/16”
(5 mm) Max.
ON
Tie Wrap
1
2
3
4
3-Pole Captive Screw Connector
Audio output — 3.5 mm captive screw stereo output
2
3
Switch Function
On (up)
monitor present
Off (down)
monitor not present
VGA output — HD 15-pin female analog video output
connector
local monitor
(set ID bits 4
and 11)
SW1
dual mono
10k ohms
n/a
stereo
510 ohms
n/a
audio output
configuration
SW2
SW3
SW4
input sync
impedance
spare
Audio output — 3.5 mm captive screw stereo or dual mono
output (DIP switch selectable, see switch SW 2 in above).
2
1
2-4
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-5
Controls and Installation, cont’d
Gain switch — To compensate for cable resistance and
3
Installing the P/2 DA2 WM F/EC F
capacitance, use a small screwdriver to slide this switch to select
the level of video gain that yields the sharpest, smear-free
picture.
Easy setup procedure
The wall-mounted P/2 DA2 WM F kit consists of the faceplate/
distribution amplifier assembly and a mounting bracket that
mounts in a wall opening and to which the faceplate assembly is
attached. The P/2 DA2 WM EC F kit consists of the faceplate/
distribution amplifier assembly that mounts in the Euro
Channel raceway.
Normal –
Unity gain
Medium –
Mid-level
peaking
and gain
NORM
MED
HIGH
3
For wall mounting only: Using the mounting template
provided in the appendix as a guide, carefully cut a
mounting hole through the wall where the mounting
bracket is to be installed.
High –
Max. peaking
& gain
1
2
3
4
P/2 DA2 D
(viewed
from rear)
For wall mounting only: Install the mud ring mounting
bracket using the supplied screws and mounting clips.
Refer to the section “Installing a mud ring bracket” for
further details.
N
Adjust the gain before installing the P/2 DA2 D
into a wall, as the gain switch will be inaccessible after
installation.
Before connecting any cables, power off all equipment. If
the optional architectural adapter plate (AAP) is being
installed, please refer to “Installing architectural adapter
plates” in this chapter.
Power input — Connect the included 12 VDC external power
supply into the 2-pole, 3.5 mm captive screw connector. Be
careful to observe the correct polarity.
4
The rear connectors are the same for both WM F and WM
F EC models. Connect the VGA output cable to the 15-pin
HD female output connector. To prevent installation
debris or objects from entering the opening in the sheet
metal just above this VGA connector, use masking tape to
temporarily cover this opening. Remove this tape after
installation is completed. Next, if there is audio output,
connect the audio output cable to the captive screw
connector. Finally, connect the power cable to the power
input connector. Refer to the “Cabling” and “Connecting
audio” sections of this chapter.
Smooth
Ridges
A
A
Power Supply
Output Cord
Before attaching the faceplate assembly to the wall
mounting bracket/Euro Channel, attach the computer
video cable to the 15-pin HD female input connector on
the faceplate. Next, a local monitor may be connected to
the 15-pin HD female buffered local monitor output
connector on the faceplate. Finally, for audio input,
connect the audio cable to the faceplate’s 3.5 mm audio
input jack. Refer to the “Cabling” and “Connecting audio”
sections of this chapter. For Euro Channel applications,
refer to the “Euro Channel installation” section.
5
SECTION A–A
Video output — BNC connectors for RGBHV output.
5
2-7
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-6
Controls and Installation, cont’d
Power up all of the input and output devices.
6
7
The image should now display on screen. If it does not,
double check steps 3 through 6 and make adjustments as
needed. Refer to the section “Setting the DIP switches” in
this chapter.
NOTE Do not disassemble the dogleg
from the dogleg screw. Rotate the
dogleg out of the way to insert the
mud ring into the wall.
For the P/2 DA2 WM F, attach the P/2 DA2 WM F to the
wall mounting bracket (see “Installing the mud ring
bracket”).
8
Dogleg
Screw
For the P/2 DA2 WM EC F, attach the P/2 DA2 WM F EC
to the Euro Channel (see “P/2 DA2 WM EC F Euro
Channel installation”).
Extron
MR 200D
Modular Mud Ring
Installing the mud ring bracket
Rotate doglegs
and insert mud
ring into wall
opening.
1.
Once the proper wall location for mounting the
distribution amplifier has been determined, cut an opening
in the wall using the proper mounting template found in
the appendix.
Surface Mounting
Hole
2.
3.
Carefully cut away the mounting surface material inside
the traced template lines.
Equipment Mounting
Holes
Test the fit of the mud ring. The doglegs should fit easily
into the hole and the flat portion should rest flush against
the wall. See the note in the following illustration.
Installing a mud ring bracket
4.
5.
6.
Rotate all doglegs inward.
Insert the mud ring into the hole.
Tighten all of the dogleg screws until the doglegs clamp
the mud ring to the mounting surface. Do not
overtighten.
Standard mud rings only: If you are going to screw the
mud ring to the surface, rather than using the detachable
doglegs, mark the four surface mounting screw holes at
the corners of the mud ring.
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-8
2-9
Controls and Installation, cont’d
Cabling
Connecting audio output
The P/2 DA2 WM F cabling diagram below shows how to
Before connecting audio output, determine whether your audio
system is unbalanced or balanced. Then, follow the instructions
below to connect unbalanced audio, or the instructions for
“Balanced audio” to connect balanced audio.
connect input and output devices to the distribution amplifier’s
front panel. The P/2 DA2 WM EC F model has identical
connectors.
C Wiring the audio incorrectly may damage the audio
output circuits.
Unbalanced audio
To attach the P/2 DA2 WM F/EC F to an unbalanced audio
system, do the following:
AUTO POWER
1.
Attach the audio cable to an unbalanced speaker input
connector (tip and sleeve).
100%
UNITY
Tip (+)
50%
GAIN/PEAKING
Sleeve (
)
2.
Attach the audio cable to the audio cable connector (Extron
part number 10-319-10). Fasten the captive screws inside
the audio cable connector.
P/2 DA2 WM F cabling
1.
Connect your display device to the 15-pin HD female
video output VGA connector on the rear of the
P/2 DA2 WM F/EC F.
Fasteningcaptivescrews
CAUTION
2.
For audio output, refer to the section “Connecting audio
output” and connect the audio output cable to the 3.5 mm
captive screw connector on the rear of the P/2 DA2 WM
F/EC F.
For unbalanced audio, connect the
sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to the
negative (-) contacts.
Tip
3.
4.
5.
Connect the power input cable to the rear power input
connector of the P/2 DA2 WM F/EC F.
Left
Right
NO Ground Here
Sleeve(s)
Tip
NO Ground Here
Connect the computer’s video cable to the 15-pin HD
female input cable on the distribution amplifier’s faceplate.
Unbalanced Output
If a local monitor is being used, connect the monitor to the
15-pin HD female buffered local monitor output on the
faceplate.
6.
For audio input, connect the input device into the front
faceplate’s 3.5 mm female audio jack.
3.
Slide the audio cable connector into the audio output
connector on the interface.
2-10
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-11
Controls and Installation, cont’d
Balanced audio
To attach the distribution amplifier to a balanced audio system,
do the following:
Adapter Plate
1.
Attach the audio cable to a balanced speaker input
connector (tip, ring, and sleeve).
AUTO POWER
AUDIO
Tip (L)
Ring (R)
100%
UNITY
INPUT
50%
GAIN/PEAKING
BUFFERED
ID PIN
ID PIN 11
4
LOCAL M
#4-40 Nut w/ Captive
Washer
Sleeve (
)
P/2 DA2 WM F AAP
(up to 4 plates)
2.
Attach the audio cable to the audio cable connector (Extron
part number 10-319-10). Fasten the captive screws inside
the audio cable connector as shown below.
P/2
D
A2
WM
F
AAP
Tip
Left
Ring
Sleeve(s)
P/2 DA2 WM F AAP EC
Tip
Right
AUTO POWER
Ring
GAIN/
PEAKING
ID PINS
P/2 DA2 WM F AAP EC
(up to 3 plates)
Balanced Output
3.
Slide the audio cable connector into the audio output
connector on the distribution amplifier.
Installingadapterplates
Installing architectural adapter plates
The P/2 DA2 WM F AAP may have up to four optional adapter
plates and the P/2 DA2 WM F AAP EC can have up to three
adapter plates. The adapter plates provide a convenient method
of adding various connectors for specific audio and video
requirements. The adapter plates must be ordered separately
and must be attached to the faceplate and cabled before
attaching the WM F AAP model to the wall mount bracket or
the EC F AAP model to the Euro Channel.
2.
Attach the output cables to the back side of the adapter
plate. Some adapter plates may require that conductors be
soldered to the connectors. Attach foil and braided shields
to ground connections.
1.
Insert the adapter plate captive screws through the front
faceplate holes. Secure the adapter plate using the
supplied washers and nuts.
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-12
2-13
Controls and Installation, cont’d
P/2 DA2 WM F wall mount installation
P/2 DA2 WM EC F Euro Channel installation
Once the input and output cables have been connected and the
P/2 DA2 WM F has been successfully tested, the faceplate may
be attached to the mounting bracket using the four supplied
screws.
Once the input and output cables have been connected and
tested on the P/2 DA2 WM F EC, the distribution amplifier can
be easily installed in the Euro Channel.
C
E
F
M
W
N
The center pole of the power input connector contains no
conductor. Connect the conductors to the two outer
poles only, exactly as shown here.
2
A
D
2
/
P
S
N
I
P
1
1
D
I
4
R
E
W
O
R
P
D
O
T
I
O
E
T
R
U
N
A
E
F
O
M
O
I
F
D
U
U
L
A
B
A
C
O
L
/
T
U
P
N
I
G
A
N
I
G
N
I
K
A
E
P
Positive
N/C
Negative
Audio (3.5 mm
Captive Screw
Connector)
Rear Cover Screws
Do not remove unless faceplate
is removed from wall.
Power (3.5 mm
Captive Screw
Connector)
C
E
F
M
W
2
A
D
2
/
P
S
N
I
P
1
1
D
I
4
R
E
W
O
R
P
D
O
T
I
O
E
T
R
U
N
A
E
F
O
M
O
I
F
D
U
U
L
A
B
A
C
O
L
/
T
U
P
N
I
G
A
N
I
G
N
I
K
A
Euro Channel
E
P
AUTO POWER
AUDIO
100%
UNITY
INPUT
50%
GAIN/PEAKING
BUFFERED
ID PIN
ID PIN 11
4
LOCAL M
P/2
D
A2
WM
F
EuroChannelinstallation
VGA Connector
Setting the DIP switches
Two sliding-type DIP switches can be found on the faceplate of
the P/2 DA2 WM F/EC F.
1
2
To set the sliding-type DIP switches, slide the switch to
the on/closed or off/open position.
The two DIP switches provide proper ID bit termination for a
laptop computer that is not attached to a local monitor.
ID Pin 4 & ID Pin 11
ON — Set both pins to On if you are using the P/2 DA2
ID PIN 4
ID PIN 11
WM F/EC F with a laptop computer that is not
attached to a local monitor.
OFF — Set both pins to Off if you are attaching a local
monitor to the
Wall mounting the P/2 DA2 WM F
P/2 DA2 WM F/EC F.
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-14
2-15
Controls and Installation, cont’d
Setting the internal jumpers
Installing the P/2 DA2 D
The jumpers (J2 and J6) inside the distribution amplifier are set
The P/2 DA2 D is a wall-mounted product and can be mounted
into an electrical wall box. These instructions include site
preparation, wall box installation, and the mounting of the
distribution amplifier in the wall box.
at the factory for output to a local monitor. However, you can
direct output to a data display by resetting the jumpers. Follow
these steps and the illustration below to change the jumper
settings. In some instances where DDC communication is
required between the display device and the computer’s
graphics card, pins 15 (J2) and 12 (J6) will carry that information.
N
The P/2 DA2 D must be installed into an Underwriters
Laboratories (UL) approved electrical wall box. The box
is not included with the distribution amplifier; the
installer is responsible for obtaining/installing the box.
C
Changes to internal jumper settings must be
performed only by authorized service personnel.
Preparing the site and installing the wall box
1.
Disconnect the power cable, then disconnect the output
and audio cables from the rear panel of the distribution
amplifier. Next, remove the rear cover by removing the
two front panel screws. See “P/2 DA2 F wall mount
installation” in this chapter for screw locations.
Choose a location that allows cable runs without interference.
Allow enough depth for both the wall box and the cables. You
may need to install the cables into the wall or conduits before
installing the distribution amplifier.
The distribution amplifier can be installed in a standard one-
gang electrical wall box. The installation must conform to
national and local electrical codes. A dimensional drawing and a
cutout template of the distribution amplifier are provided in
appendix A of this manual.
2.
Using a pair of tweezers or needle-nosed pliers, set
jumpers J2 and J6, as shown below in figure 2-10.
C
Be sure you are electrically grounded before
touching any circuit board components.
• Connect pins 1 and 2 on both jumpers (factory default)
to output to the 15-pin female local monitor connector
on the front panel.
N
The cutout template of the P/2 DA2 D shown in
appendix A is not full size. Pay attention to the
measurements shown in the template.
or
1.
Mark the guidelines for the opening on the wall.
•
Connect pins 2 and 3 on both jumpers to output to the
rear 15-pin female output.
• If the distribution amplifier will be installed in a wall
box, place the box against the installation surface and
draw a line on it around the outside of the box.
• If the distribution amplifier will be installed without a
wall box (fastening it directly to the wall), measure and
mark the surface for the cutout area indicated in the
cutout template.
2.
3.
Cut out the material from the marked area.
1-2 = Local Monitor (default)
2-3 = Data Display
Check the opening size by inserting the wall box (if used)
or the distribution amplifier (if no box is used) into the
opening. Enlarge or smooth the edges of the opening if
needed.
1-2 = Local Monitor (default)
2-3 = Data Display
3
J2
2
1
J6
ID Pin Pass Through Jumpers
P/2 DA2 WM F Rear View
(cover removed)
4.
5.
Feed the cables through the wall box punch-out holes, and
secure them with cable clamps to provide strain relief.
Settingtheinternaljumpers
Insert the wall box into the opening, and attach it to the
wall or stud using nails or screws. The front edge should
be flush with the outer wall surface. See the following
illustration.
3.
Replace the rear cover and reconnect the output cable.
Reconnect the power and/or audio cables.
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-16
2-17
Controls and Installation, cont’d
3.
Mount the distribution amplifier to the wall box with
machine screws, as shown in the following illustration.
Wall Stud
Wall Stud
Installation Cable
Cable Clamp
Installation Cable
Cable Clamp
Wall Box
Screws or Nails
Screws or Nails
Extron
P2 DA2 D
UDIO IN
A
Wall opening
is flush with
edge of box.
COMPUE
OR OUT
MONIT
Attaching the wall box to a wall stud
If attaching the wall box to wood, use four #8 or #10 screws or
10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw
threads must penetrate the wood.
If attaching the wall box to metal studs, use four #8 or #10 self-
tapping sheet metal screws or machine bolts with matching
nuts.
Decora
Faceplate
Mounting the distribution amplifier
Mountingthedistributionamplifiertothewallbox
Before mounting the distribution amplifier and if it has not
already been tested, test the system to make sure that the
connections and settings are correct.
4.
5.
Attach the Decora cover plate to the line driver, as shown
in the previous illustration.
Reconnect the power supply and restore power to the
equipment.
If the system is operating correctly, the distribution amplifier
can be installed in the wall. Adjust the gain and set the DIP
switches before fastening the distribution amplifier into the wall
box. The controls and cables will be inaccessible after
installation. See “Rear Panel Features and Operation” in this
chapter for details about settings and adjustments.
Continue mounting the distribution amplifier by following the
steps below.
1.
Remove power from the distribution amplifier by
disconnecting the power supply.
2.
Place the distribution amplifier through the opening in the
wall and into the wall box. Take care not to damage the
output cable(s), which fit behind the distribution amplifier
at the back of the wall box.
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
Download from Www.Somanuals.com. All Manuals SearchPA/n2d DDoAw2nloWadM. /EC/D/AAP Series • Controls and Installation
2-18
2-19
Controls and Installation, cont’d
Replacing the faceplate
P/2 DA2 WM/EC/D/AAP Series
The front faceplate is replaced by removing the two rear panel
mounting screws, replacing the faceplate, then reattaching the
two screws, as shown below.
NORM
MED
HIGH
Mounting
Back Panel
Screws
Faceplate (rear)
P/2 DA2 D application example
Appendix A
An example of the P/2 DA2 D installation is shown below.
Extron
SI 3CT LP
Full-Range Ceiling
Speakers
A
Specifications, Dimensions,
Parts, and Templates
Specifications
Projector
2
2
1
A
P
S
T
M
U
P
ERS
T
U
O
PEAK
R
L
4/8 Ohms
S
S
U
C
E
T
O
S
M
E
T
U
R
P
N
I
UTE
10V
M
/
L
VO
R
L
L
R
X
E
W
Extron
MHR-5 Cable
O
P
R
Extron
.
V
2
A
Dimensions
1
A
M
3
MPA 122
Mini Power Amplifier
Audio
Output
PartsandAccessories
IN
O
T
I
D
U
A
T
I
R
E
U
P
Audio
M
O
C
Templates
U
O
R
O
IT
N
O
M
Extron
P/2 DA2 D
Distribution Amplifier
PC w/ Audio
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts
Video output
Number/signal type
Specifications
Video
Gain
P/2 DA2 D ........................ 1 VGA–QXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video main
output
1 VGA–QXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video local
monitor output
P/2 DA2 D ........................ Main output: 0 dB, 0.6 dB, 1.2 dB,
selectable
Local monitor output: unity
P/2 DA2 WM F, P/2 DA2 WM F AAP
Switchable: 0 dB, +1.2 dB, +2.2 dB(0.7 V,
0.8 V, or 0.9 V when input is 0.7 V and the
gain/peaking switch is set to Unity, 50%,
or 100%, respectively)
P/2 DA2 WM F, P/2 DA2 WM F AAP
2 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video (with
adapter)
Bandwidth
Connectors
P/2 DA2 D
Main output .............. 5 female BNC on 3" pigtails
Local monitor ........... 1 female 15-pin HD
P/2 DA2 WM F, P/2 DA2 WM F AAP
(2) 15-pin HD female (1 display, 1 local
P/2 DA2 D ........................ 350 MHz (-3 dB)
P/2 DA2 WM F, P/2 DA2 WM F AAP
300 MHz (-3 dB)
N
ID bits can be terminated (pins 4 and 11) via a switch setting.
monitor)
Video input
Number/signal type
Nominal level ............................... 1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels ....... Analog: 0.4 V to 1.4 Vp-p (follows input)
Impedance .................................... 75 ohms
P/2 DA2 D ........................ 1 VGA–QXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video
P/2 DA2 WM F, P/2 DA2 WM F AAP
1 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video
Return loss (P/2 DA2 D) ............. <-38 dB @ 5 MHzP/2 DA2 WM F,
P/2 DA2 WM F AAP<-40 dB @ 5 MHz
Connectors ................................... (1) female 15-pin HD
DC offset (P/2 DA2 D) ................ 5 mV with input at 0 offset
Nominal level ............................... 1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels ....... Analog: 0.4 V to 1.4 Vp-p with no offset at
unity gain
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 135 kHz
Vertical frequency ....................... 30 Hz to 170 Hz
Return loss .................................... <-38 dB @ 5 MHz
DC offset (max. allowable)
Sync
Input type ..................................... RGBHV, RGBS, RGsB, RsGsBs, bi-level and
tri-level component video sync
Output type .................................. RGBHV, RGBS, RGsB, RsGsBs, bi-level and
tri-level component video sync
Input level ..................................... 3.0 V to 5.0 Vp-p
Outputlevel .................................. 0.3 Vp-p for component video (bi-level
sync)
0.6 Vp-p for component video (tri-level
sync)
TTL: 5.0 Vp-p, unterminated for RGBHV,
RGBS
P/2 DA2 D ........................ 5 mV
P/2 DA2 WM F, P/2 DA2 WM F AAP
200 mV
Input impedance .......................... 510 ohms or 10k ohm, switch selectable
Input coupling (P/2 DA2 D) ....... DC
A-2
A-3
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, Parts, cont’d
Outputimpedance
Audio output
Number/signal type
P/2 DA2 D ........................ 75 ohms
P/2 DA2 WM F, P/2 DA2 WM F AAP
40 ohms, typical
Max. propagation delay
P/2 DA2 D ........................ 1 stereo or dual mono (switch selectable),
balanced/unbalanced
P/2 DA2 WM F, P/2 DA2 WM F AAP
P/2 DA2 D ........................ 60 ns
1 stereo, balanced/unbalanced
P/2 DA2 WM F, P/2 DA2 WM F AAP
18.8 ns
Connectors ................................... (1) 3.5 mm direct insertion captive screw
connector, 5 pole
Max. rise/fall time ....................... 4 ns
Polarity .......................................... Positive or negative (follows input)
Impedance .................................... 50 ohms unbalanced, 100 ohms balanced
Gain error (P/2 DA2 D) .............. 0.5 dB channel to channel
Maximum level (Hi-Z) ................ +15 dBu, balanced or unbalanced,
at 1% THD+N
Audio
Gain ................................................ Unbalanced output: 0 dB; balanced output:
+6 dB
Maximum level (600 ohm) ......... +9 dBm, balanced or unbalanced,
at 1% THD+N
Frequency response .................... 20 Hz to 20 kHz, 0.05 dB
THD + Noise ................................. 0.03% @ 1 kHz at nominal level
S/N ................................................ >90 dB at maximum output (unweighted)
Crosstalk (P/2 DA2 D) ................ <-80 dB @ 1 kHz
Stereo channel separation (P/2 DA2 D)
>80 dB @ 1 kHz
General
External power supply ................ 100 VAC to 240 VAC, 50/60 Hz, external;
to 12 VDC, 1 A (max.), regulated
Power input requirements .........
12 VDC, 0.2 A
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
CMRR (P/2 DA2 D) ..................... >67 dB @ 20 Hz to 20 kHz
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling .......................................... Convection, no vents
Mounting ...................................... Wall or furniture mountable
Enclosure type
Audio input
Number/signal type ................... 1 stereo, unbalanced
Connectors ................................... (1) 3.5 mm mini stereo jack (tip, ring,
sleeve)
Impedance
P/2 DA2 D ........................ Metal faceplate and a plastic Decora® wall
plate
P/2 DA2 WM F, P/2 DA2 WM F AAP
Metal
P/2 DA2 D ........................ >18k ohms unbalanced, DC coupled
P/2 DA2 WM F, P/2 DA2 WM F AAP
>5k ohms unbalanced, DC coupled
Nominal level ............................... -10 dBV (316 mVrms)
Maximum level
Enclosure dimensions
P/2 DA2 D
P/2 DA2 D ........................ +10 dBV, (unbalanced) at 1% THD+N
P/2 DA2 WM F, P/2 DA2 WM F AAP
+8.5 dBu (unbalanced) at 1% THD+N
Faceplate ................... 2.6" H* x 1.3" W x 0.1" D
(6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang Decora
faceplate. *Height is 3.8" [9.7 cm] including
mounting tabs.)
N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu
Buffer ......................... 2.7" H x 1.8" W x 0.75" D*
(6.9 cm H x 4.6 cm W x 1.9 cm D*)
(*Depth excludes BNC connectors and
cables.)
A-4
A-5
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts, cont’d
P/2 DA2 WM F
Dimensions
Faceplate ................... 4.5” H x 4.6” W x 0.1” D
(11.4 cm H x 11.7 cm W x 0.3 cm D)
(2 gang)
Box ............................. 2.6” H x 3.7” W x 1.6” D
(6.6 cm H x 9.4 cm W x 4.1 cm D)
Dimensions of the P/2 DA2 WM F and its AAP version are
provided here for those who wish to make their own
customized faceplates. The following diagrams are not drawn
to scale.
All dimensions are given in inches.
P/2 DA2 WM F AAP
Faceplate ................... 4.5” H x 8.3” W x 0.1” D
(11.4 cm H x 21.1 cm W x 0.3 cm D)
(4 gang)
Box ............................. 2.6” H x 3.7” W x 1.6” D
(6.6 cm H x 9.4 cm W x 4.1 cm D)
P/2 DA2 WM F faceplate dimensions
Product weight
P/2 DA2 D ........................ 0.2 lbs (0.1 kg)
P/2 DA2 WM F ................ 0.4 lbs (0.2 kg)
P/2 DA2 WM F AAP ....... 0.6 lbs (0.3 kg)
Shipping weight ........................... 2 lb (1 kg)
HAND SAND TO 0.06" RADIUS
AROUND THE TOP OF
THESE EDGES.
Vibration ....................................... ISTA 1A in carton (International Safe
TransitAssociation)
THRU
Listings .......................................... UL, CUL
Regulatory compliance
.120 THRU
.210 THRU
Safety ................................. CE, C-tick, UL. CUL
EMI/EMC ......................... CE, FCC Class A, VCCI, C-tick, ICES
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
.210 THRU
N
N
All nominal levels are at 10%.
DETAIL A
Specificationsaresubjecttochangewithoutnotice.
DETAIL A
WMFmodelfaceplatedimensions
A-6
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts, cont’d
P/2 DA2 WM F AAP faceplate dimensions
P/2 DA2 D faceplate dimensions
.060 [1.524]
.600 [15.500]
.100 [2.540]
2.830 [71.882]
0.000 [0.000]
2.720 [69.088]
0.110 [2.794]
0.000 [0.000]
2.720 [70.000]
WMFAAPmodelfaceplatedimensions
Front View
Side View
Dmodelfaceplatedimensions
A-8
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
A-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts, cont’d
Parts and Accessories
Optional architectural adapter plates
A variety of optional adapter plates for pass-through
connections may be ordered for the P/2 DA2 WM F AAP and
P/2 DA2 WM F AAP EC. See the figure below. The WM F AAP
model can accommodate up to four adapter plates and the
WM F AAP EC model can handle up to three adapter plates.
The adapter plates come in one and two-high sizes.
Included Parts
The table below lists part numbers of the various models.
Model
Part number
P/2 DA2 WM F (black, white,
RAL9010 white)
60-376- (-02, -03, -05)
The WM F AAP model may be configured as follows:
• 4 adapter plates of plate size one or
P/2 DA2 EC F (RAL9010 white)
60-376-10
P/2 DA2 WM F AAP (black, white,
RAL9010 white)
60-377- (-02, -03, -05)
• 2 adapter plates of plate size two or
P/2 DA2 WM EC F AAP (RAL9010 white) 60-377-10
• 2 adapter plates of plate size one and one adapter
plate of plate size two
P/2 DA2 D (black, white)
User manual
60-955- (-02, -03)
The WM F AAP EC model may be configured as follows:
Cables
• 3 adapter plates of plate size one or
The table below lists various lengths of high resolution VGA
cables which can be used with the P/2 DA2 WM F/WM F AAP/
EC F/D models.
• 1 adapter plate of plate size two and 1 adapter plate
of plate size one
Blank Plate (no connector)
Single Space
Blank Plate (no connector)
Double Space
Male-to-female VGA cables
Part number
2 - BNC
VGA 6’ MHR
26-238-01
26-490-01
26-490-02
26-490-03
26-490-04
26-490-05
5 - BNC (Double)
VGA 3’ MHR A (with audio)
VGA 6’ MHR A (with audio)
VGA 12’ MHR A (with audio)
VGA 25’ MHR A (with audio)
VGA 50’ MHR A (with audio)
3 - BNC
2 - RCA to Solder Cups
3 - RCA to Solder Cups
2 - S-video
2 - RJ-11
1 - D-9 Pass Through Connector
Mud ring mounting brackets
The table below lists various mud ring mounting brackets.
MR Series mud ring brackets
Part number
Examplesofadapterplates
MR 100, 1-gang, black or white
MR 100D, 1-gang, Decora ®, black
MR 200, 2-gang, black or white
70-519-12 or -13
70-581-12
The tables on following pages list the available adapter plates
and distinguish between plates with a single type of connector
(single type) or plates with more than one type of connector
(multi type).
70-519-22 or -23
A-10
A-11
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts, cont’d
A-12
A-13
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts, cont’d
Templates
Use these templates as a guide for cutting the hole in the
installation surface (wall or furniture).
N
This templates for the P/2 DA2 WM F and the P/2 DA 2
WM F AAP are not full size.
Do not scale.
P/2 DA2 WM F mounting template
Cut-Out Template for Extron's
P/2 DA2 WM F
4.60" (11.68 cm)
Wall Plate
3.58" (9.10 cm)
To install P/2 DA2
directly into
furniture or wall,
cut along this line.
4.50"
(11.43 cm)
2.68"
(6.80 cm)
SURFACE CUT-OUT AREA
FOR FURNITURE MOUNT
Location of P/2 DA2
TEMPLATE IS NOT FULL SIZE.
A-14
A-15
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts, cont’d
P/2 DA2 WM F AAP mounting template
P/2 DA2 D mounting template
Cut-Out Template for Extron's
P/2 DA2 WM F AAP
Cut-Out Template for Extron's
4.50" (11.43 cm)
P/2 DA2 D
2.79"
(7.09 cm)
Wall Plate
2.68" (6.80 cm)
Wall Plate
1.88"
(4.78 cm)
To install P/2 DA2
directly into
furniture or wall,
cut along this line.
SURFACE CUT-OUT
AREA FOR
FURNITURE MOUNT
4.50"
(11.43 cm)
2.80"
(7.11 cm)
Location of Line Driver
8.23
(20.90 cm)
SURFACE
CUT-OUT AREA
FOR
FURNITURE
MOUNT
"
To install Line Driver
directly into
furniture or wall,
cut along this line.
7.31"
(18.28 cm)
Location of P/2 DA2
TEMPLATE IS FULL SIZE.
Please measure the printed template before cutting.
TEMPLATE IS NOT FULL SIZE.
A-16
A-17
P/2 DA2 WM/EC/D/AAP Series • Appendix
P/2 DA2 WM/EC/D/AAP Series • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Dimensions, and Parts, cont’d
A-18
P/2 DA2 WM/EC/D/AAP Series • Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
|