User’s Guide
DVI DA Plus Series
DVI Distribution Amplifiers
68-1536-01
Rev. A
09 08
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
这个符号提示用户该设备用户手册中
电源 • 该设备只能使用产品上标明的电源。 设备
必须使用有地线的供电系统供电。 第三条线
（地线）是安全设施，不能不用或跳过。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
注意
阅读说明书 • 用户使用该设备前必须阅读并理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
声明
所使用电源为 A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用
户对其干扰采取切实可行的措施。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
N
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — DVI DA Plus Series
To install, connect cables, and operate any of the DVI DA Plus Series
distribution amplifiers, follow these steps:
Step 1: Install
Install the distribution amplifier on a desk, under a desk, or in a rack
(see page 2-2).
Step 2: Connect Power Cables
Connect the 12 VDC power supply (provided with the unit) to the
unit's power receptacle, using the two pole, 3.5mm captive screw
connector (see page 2-8).
POWER
12V
1.0A MAX
Back Panel
Power Receptacle
DC Power Cord
Captive Screw Connector
Ground
+12 VDC
External
Power Supply
(12 VDC, 2 A )
AC Power Cord
The external power supply in the illustration above (12 VDC, 2A)
is for use with the DVI DA4 Plus. The DVI DA6 Plus and DVI DA8
Plus use a 12 VDC, 3A external power supply.
DVI DA Plus Series • Quick Start Guide
QS-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — DVI DA Plus Series, cont’d
Step 3: Connect DVI Cables
Connect a DVI cable from the Input connector to the video
source device (see page 2-9).
Connect a DVI cable from the distribution amplifier to the desired
display device(s) (see page 2-9).
DVI DA8 Plus
8
7
6
5
T
DVI-D OUTPU
4
3
2
1
T
DVI-D INPU
R
POWE
V
X
12
MA
0.4A
Display
with
DVI Input
Extron
DVI DA8 Plus
Distribution Amplifier
Display
with
DVI Input
Computer
Local
Monitor
with
DVI Output
Step 4: Apply Power
Power on the display device(s).
Power on the distribution amplifier.
Power on the source input device.
For the distribution amplifier's EDID Minder feature to work
correctly, the distribution amplifier and all the display devices
must be powered on before the source device is booted up.
N
DVI DA Plus Series • Quick Start Guide
QS-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter One • Introduction.................................................... 1-1
About This Manual.................................................................... 1-2
About the DVI DA Plus Series................................................ 1-2
DVI DA Plus Series Features................................................... 1-3
Chapter Two • Installation and Operation................... 2-1
Installation Overvieꢀ............................................................... 2-2
Mounting the Distribution Amplifier.................................. 2-2
Tabletop placement ............................................................... 2-2
Rack mounting....................................................................... 2-2
UL guidelines for rack mounting...........................................2-2
Rack mounting the DVI DA4 Plus..........................................2-3
Rack mounting the DVI DA6 Plus and DVI DA8 Plus............2-4
Under-desk mounting............................................................ 2-5
Front Panel Features................................................................. 2-6
Rear Panel Features................................................................... 2-7
Poꢀer supply input................................................................ 2-8
Input cable connections......................................................... 2-9
Output cable connections ..................................................... 2-9
DVI connector pin assignments .......................................... 2-10
Operation................................................................................... 2-11
Troubleshooting....................................................................... 2-12
Appendix A • Reference Information ............................A-1
Specifications..............................................................................A-2
Included Parts .............................................................................A-4
Accessories...................................................................................A-4
All trademarks mentioned in this manual are the properties of their respective owners.
68-1536-01
Rev. A
09 08
DVI DA Plus Series • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
DVI DA Plus Series • Table of Contents
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DA Plus Series
Chapter One
1
Introduction
About this manual
About the DVI DA Plus Series
DVI DA Plus Series Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About This Manual
This manual describes the installation, operation, and
specifications of the Extron DVI DA4 Plus, DVI DA6 Plus, and
DVI DA8 Plus Distribution Amplifiers.
Unless stated otherwise, all references to the "distribution
amplifier" or "DVI DA Plus Series" in this manual refer to the
features or operation of all three models.
About the DVI DA Plus Series
These Digital Visual Interface (DVI) Distribution Amplifiers
(DAs) accept one single link DVI-D input and distribute four
(DVI DA4 Plus), six (DVI DA6 Plus), or eight (DVI DA8 Plus)
single link DVI-D output signals.
All three models use Extron's EDID Minder feature to maintain
continuous EDID (Extended Display Identification Data)
communication with the attached source. This ensures that the
DVI source powers up correctly and maintains a proper video
output, even if the display is off.
The DVI DA4 Plus is 1U high and half a rack wide. The DVI
DA6 Plus and DVI DA8 Plus are both 1U high and a full rack
wide. All three models offer a variety of mounting options.
The illustration below shows a typical application of the
DVI DA8 Plus.
DVI DA8 Plus
8
7
6
5
T
DVI-D OUTPU
4
3
2
1
T
DVI-D INPU
R
POWE
V
X
12
MA
0.4A
Display
with
DVI Input
Extron
DVI DA8 Plus
Distribution Amplifier
Display
with
DVI Input
Computer
Local
Monitor
with
DVI Output
DVI DA Plus Series • Introduction
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DA Plus Series Features
EDID Minder — The EDID Minder maintains continuous EDID
(Extended Display Identification Data) communication with
the attached source. This ensures that the DVI source powers
up correctly and maintains a proper video output, even if the
display is off.
High Resolution DVI-D input — The distribution amplifiers
accept one single link DVI-D input, with a resolution range up
to 1920 x 1200 or 1080p @ 60 Hz.
Input Equalization — Input Equalization (EQ) conditions the
input signals to ensure the integrity of the signals delivered to
the output devices.
DVI-D outputs — The units distribute four (DVI DA4 Plus),
six (DVI DA6 Plus), or eight (DVI DA8 Plus) single link DVI-D
output signals simultaneously, at resolutions up to 1920 x 1200
or 1080p @ 60 Hz.
The actual signal transmission distance can vary greatly
and depends on signal resolution, cable type, cable
quality, graphics card and the display used in the system.
N
External power supply — All three models are powered by
external 12 VDC power supply (provided with the units).
Power on Pin 14 — The distribution amplifiers are able to
provide a 5 VDC (250 mA) output.
Front Panel Indicator LED — The LED light on the front panel
provides feedback about power status and whether an input
signal is detected.
Versatile mounting options — All three units can be mounted
in a rack, under a desk or set on a tabletop.
DVI DA Plus Series • Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, contd
DVI DA Plus Series • Introduction
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DA Plus Series
Chapter Two
2
Installation and Operation
Installation Overview
Mounting the Distribution Amplifier
Front Panel Features
Rear Panel Features
Operation
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
Installation Overview
All three distribution amplifiers can be mounted on tabletops,
under furniture, and in racks by following these steps:
1. Ensure that the input sources, the distribution amplifier and
the output display(s) are all turned off and all power sources
and signal cables are disconnected.
2. Mount the unit as described in "Mounting the Distribution
Amplifier", below.
3. Connect the cables (see page 2-9).
4. Plug in the power supply, turn on the display devices and,
finally, turn on the input devices (see page 2-11).
Mounting the Distribution Amplifier
All three of these units can be mounted in racks, under furniture
or on tabletops.
Tabletop placement
Attach the four provided rubber feet to the bottom of the unit
and place it in any convenient location.
Rack mounting
UL guidelines for rack mounting
The following Underwriters Laboratories (UL) guidelines are
relevant to the safe installation of these products in a rack:
1. Elevated operating ambient temperature — If the unit
is installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore,
install the equipment in an environment compatible with
the maximum ambient temperature (Tma: +122 °F, +50 ° C)
specified by Extron.
2. Reduced air flow — Install the equipment in the rack so that
the equipment gets adequate air flow for safe operation.
3. Mechanical loading — Mount the equipment in the rack so
that uneven mechanical loading does not create a hazardous
condition.
4. Circuit overloading — Connect the equipment to the supply
circuit and consider the effect that circuit overloading might
have on overcurrent protection and supply wiring. Give
appropriate consideration to the equipment nameplate
ratings when addressing this concern.
DVI DA Plus Series • Installation and Operation
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct connections
to the branch circuit (such as the use of power strips).
Rack mounting the DVI DA4 Plus
The DVI DA4 Plus can be mounted on the following (optional)
rack shelves:
•
•
•
•
•
•
RSF 123 (3.5" deep, 1U rack shelf kit: part # 60-190-20)
RSB 123 (3.5" deep, 1U basic rack shelf: part # 60-604-20)
RSU 126 (6" deep, 1U rack shelf kit: part # 60-190-10)
RSB 126 (6" deep, 1U basic rack shelf: part # 60-604-10)
RSU 129 (9.5" deep, 1U rack shelf kit: part # 60-190-01)
RSB 129 (9.5" deep, 1U basic rack shelf: part # 60-604-01)
To mount the units, follow these instructions:
1. Remove the rubber feet if these have been installed on the
bottom of the unit.
2. Align the unit on the shelf and secure it to the shelf with
two 4-40 x 3/16" screws in diagonally opposite corners (see
the figure below).
3. Install false faceplate(s) or other unit(s) to the rack shelf.
4. Attach the shelf to the rack with the four provided
10-32 x 3/4" bolts.
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
Front false
faceplate
uses 2
screws.
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
Rack mounting the DVI DA4 Plus
DVI DA Plus Series • Installation and Operation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Rack mounting the DVI DA6 Plus and DVI DA8 Plus
The DVI DA6 Plus and DVI DA8 Plus distribution amplifiers
can be mounted using the Extron MBD 149 rack mount kit
(provided) as follows:
1. Remove rubber feet if these have been installed on the
bottom of the unit.
2. Secure one bracket to each side of the distribution amplifier
with the provided bracket mounting screws (four #8 screws
for each bracket — see the figure below).
MBD 149 Bracket
FRONT
Rack mounting screws
Bracket mounting screws
Rack mounting the DVI DA6 Plus or DVI DA8 Plus
3. Align the holes in the mounting brackets with holes in the
rack and secure the unit with brackets to the rack using the
four rack-mounting screws and four washers provided with
the mounting kit.
DVI DA Plus Series • Installation and Operation
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Under-desk mounting
Mount the DVI DA6 Plus or DVI DA8 Plus (not shown) under
furniture, using the optional Extron MBU 149 under-desk
mounting kit (part # 70-222-01). Mount the DVI DA4 Plus using
the optional Extron MBU 125 under-desk mounting kit (part
# 70-077-01) as shown in the figure below. Follow the same
instructions with either kit:
Under furniture mounting the DVI DA4 Plus
To mount the unit under a desk or table:
1. If necessary, remove rubber feet from the bottom of the unit.
2. Secure the under-desk mounting brackets to the unit with the
four (DVI DA4 Plus) or eight (DVI DA6 Plus/DVI DA8 Plus)
provided #8 screws.
3. Hold the unit, with the mounting brackets attached, under
the furniture where it will be secured. Mark the position of
the holes on the underside of the furniture.
4. In the marked positions, drill four pilot holes 3/32" in
diameter and 1/4" deep.
5. Insert the four provided wood screws into the pilot holes
and tighten until approximately 1/4" of the screw head is
protruding.
6. Guide the holes of the mounting brackets over the
protruding screw head and slide the unit forward or
backward to seat it firmly under the furniture.
7. Tighten all four wood screws to secure the unit in place.
DVI DA Plus Series • Installation and Operation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Front Panel Features
The front panels for the DVI DA4 Plus (upper panel) and the
DVI DA6 Plus/DVI DA8 Plus (lower panel) are shown below:
DVI DA PLUS
DVI DISTRIBUTION AMPLIFIER
1
DVI DA Plus SERIES
DVI DISTRIBUTION AMPLIFIER
1
Front panel features
LED indicator — This LED indicator illuminates amber when
the unit is receiving power but no input signal. When the unit
detects an input signal, the LED illuminates green.
a
DVI DA Plus Series • Installation and Operation
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel Features
The rear panels for the DVI DA4 Plus (top panel), the DVI DA6
Plus (middle panel), and DVI DA8 Plus (bottom panel) are
shown below:
DVI DA4 Plus
POWER
12V
1.0A MAX
DVI-D INPUT
DVI-D OUTPUT
1
2
3
4
2
3
4
DVI DA6 Plus
DVI-D OUTPUT
DVI-D INPUT
POWER
12V
1.5A MAX
1
2
3
4
5
6
2
3
4
DVI DA8 Plus
DVI-D OUTPUT
4
DVI-D INPUT
POWER
12V
1.5A MAX
1
2
3
5
6
7
8
Rear panel features
Power input — Connect the external power supply (provided)
to the 3.5 mm, 2-pole captive screw power receptacle.
b
c
d
Input connector — Connect the input signal to the female DVI-I
connector. The DVI input signal is equalized to ensure integrity.
Output Connectors — Connect up to four (DVI DA4 Plus),
six (DVI DA6 Plus) or eight (DVI DA8 Plus) DVI-D outputs to
display devices, using the female DVI-I connectors.
Although these distribution amplifiers have DVI-I
connectors, they are only compatible with single-link
DVI-D video signals.
N
The DVI DA Plus series distribution amplifiers are not
HDCP compliant.
N
DVI DA Plus Series • Installation and Operation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Power supply input
Connect the two pole, 3.5 mm captive screw connector from the
power supply (provided with the unit) to this orange socket on
the rear panel.
POWER
12V
1.0A MAX
Back Panel
Power Receptacle
DC Power Cord
Captive Screw Connector
Ground
+12 VDC
External
Power Supply
(12 VDC, 2 A )
AC Power Cord
The external power supply in the illustration above (12 VDC,
2A) is for use with the DVI DA4 Plus. The DVI DA6 Plus and
DVI DA8 Plus use a 12 VDC, 3A external power supply.
DVI DA Plus Series • Installation and Operation
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Input cable connections
Connect a single link DVI-D source device, with a resolution
range up to 1920 x1200 or 1080p @ 60 Hz, to the female DVI-I
input, using a DVI cable.
Although these distribution amplifiers have DVI-I
connectors, they are only compatible with single-link
DVI-D video signals.
N
Input EQ conditions input signals to ensure the integrity of the
signals delivered to the output devices.
Output cable connections
Use DVI-I cables to connect up to four (DVI DA4 Plus),
six (DVI DA6 Plus) or eight (DVI DA8 Plus) display devices.
The actual signal transmission distance can vary and
depends on signal resolution, cable quality, graphics
card, and display used in the system.
N
DVI DA Plus Series • Installation and Operation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
DVI connector pin assignments
The illustration below shows the pin assignments for the
DVI-I connectors.
Although DVI-I dual link connectors are used, these
distribution amplifiers are only compatible with single-
link DVI-D video signals.
N
DVI - Female
1
8
9
17
24
Pin
1
Signal
Pin
Signal
Pin
Signal
TMDS data 2–
TMDS data 2+
9
TMDS data 1–
17 TMDS data 0–
18 TMDS data 0+
2
10 TMDS data 1+
TMDS data
2/4 shield
TMDS data
11
TMDS data
19
3
1/3 shield
0/5 shield
4
5
12
13
20
21
Spare
Spare
Spare
Spare
Spare
Spare
TMDS clock
shield
6
7
8
DDC clock
DDC data
Spare
14
15
+5 V power
Ground
22
23 TMDS clock+
16 Hot plug detect 24
TMDS clock–
DVI DA Plus Series • Installation and Operation
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
1.
Connect the captive screw connector from the supplied
12 VDC power supply into the power receptacle on the
rear panel. Do not power on the power supply yet.
2.
3.
Connect the source device to the DVI input receptacle on
the rear panel.
Run cables from the display device(s) and connect them to
the DVI output receptacles on the rear panel.
4.
Power on the display device(s).
5.
Power on the distribution amplifier. The LED will light
amber to show that the unit is receiving power.
6.
Power on the input device.
When a DVI video source boots up it normally communicates
with the output device using the bi-directional Extended
Display Identification Data (EDID) communication protocol.
The output device then produces a signal with a resolution that
is compatible with the output device.
Extron's EDID Minder feature maintains continuous EDID
(Extended Display Identification Data) communication with
the attached source and ensures that the DVI source powers
up correctly and maintains a proper video output, even if the
display is off or when a new monitor is connected to the output.
When the distribution amplifier is powered on, it automatically
scans all detectable outputs, selects the device with the lowest
native resolution and passes the EDID information of that
device to the input device.
If no output displays are connected, the distribution amplifier
provides the EDID information stored from the last display to
which it was connected. If no output device has previously been
connected to the unit, or the unit has been set to the factory
default, it uses the factory default resolution (1024 x 768).
DVI DA Plus Series • Installation and Operation
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Troubleshooting
No output signal — Check that the front panel LED is on
(amber shows that the unit is receiving power, green shows that
it is also receiving an input signal). If LED is not lit, check the
power supply and/or video input connections to the unit (see
page 2-6).
No output signal or poor quality signal — Check the integrity
of the cabling from the source device to the distribution
amplifier and from the distribution amplifier to each of the
display devices.
DVI signals run at very high frequency and poor connections
can cause degradation or loss of the signal, or jitter.
•
Signal transmission distance can vary greatly and depends
on signal resolution, cable type, cable quality, graphics card
and the display used in the system.
•
•
Use only cable that is designed for DVI signals.
Limit or avoid the use of adapters or couplers.
Display device displays a flashing black or blue screen, snow
or other distortion — A device that is not HDCP compliant may
be receiving HDCP-encrypted signals.
The DVI DA Plus series distribution amplifiers are not
High-Bandwidth Digital Content Protection (HDCP) compliant.
Signal on some displays but not others — Reboot the source
device.
When the source device boots up, the distribution amplifier's
EDID handling feature ensures that the output resolution of
the source device is matched to the requirements of the display
device with the lowest resolution.
If an additional display device is added, which requires an even
lower resolution, the image will not be displayed correctly on
that monitor until the source device is shut down and rebooted.
At that time, the distribution amplifier's EDID handling
will ensure that the output resolution of the source device is
recalibrated to meet the needs of the additional display device.
DVI DA Plus Series • Installation and Operation
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
DVI DA Plus Series
Appendix A
A
Reference Information
Specifications
Included Parts
Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Information
Specifications
*Appropriate DVI-D to HDMI cables or adapters are required
for HDMI signal input/output.
N
Video
Maximum data rate....................... 4.95 Gbps (1.65 Gbps per color)
Maximum pixel clock ................... 165 MHz
Resolution Range .......................... Up to 1920 x 1200 or 1080p @ 60 Hz
Formats........................................... RGB and YCbCr digital video
Standards........................................ DVI 1.0, HDMI 1.2
Video Input
Numbers/signal type................... 1 single link DVI-D (or HDMI*)
Connectors ..................................... 1 female DVI-I
Video Output
Numbers/signal type................... 4, 6 or 8 (depending on model) single link
DVI-D (or HDMI*)
Connectors ..................................... 4, 6 or 8 female DVI-I
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external;
to 12 VDC, regulated
DVI DA4 Plus .................... 2 A
DVI DA6 Plus, DVI DA8 Plus
3 A
Power input requirements........... 12 VDC
DVI DA4 Plus .................... 1.0 A (max)
DVI DA6 Plus, DVI DA8 Plus
1.5 A (max)
Temperature/humidity................ Storage - 40° to + 158°F (-40° to + 70°C) /
10% to 90%, noncondensing
Operating + 32° to + 122°F (0° to + 50°C) /
10% to 90%, noncondensing
Cooling ........................................... Convection, no vents
Rack mount.................................... Yes, with included brackets
Enclosure type ............................... Metal
DVI DA Plus Series • Reference Information
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Enclosure dimensions
DVI DA4 Plus ....................1.75" H x 8.75" W x 3.0" D
(1U high, half rack wide)
4.4 cm H x 22.2 cm W x 7.6 cm D
(Depth excludes connectors.)
DVI DA6 Plus, DVI DA8 Plus
1.75" H x 17.5" W x 8.5" D
(1U high, full rack wide)
4.4 cm H x 44.4 cm W x 21.6 cm D
(Depth excludes connectors.)
Product weight .............................. 2.8 lbs (1.3 kg)
Shipping weight ............................ 5 lbs (3 kg)
Vibration......................................... ISTA 1A in carton (International Safe
Transit Association)
Listings............................................ UL, CUL
Compliances................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF............................................... 30,000 hours
Warranty......................................... 3 years parts and labor
All nominal levels are at 10%
N
N
Specifications are subject to change without notice
DVI DA Plus Series • Reference Information
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Information
Included Parts
These items are included in each DVI DA Plus series amplifier:
Included parts
Replacement
part number
DVI DA4 Plus
DVI DA6 Plus
or DVI DA8 Plus
60-846-01
60-932-01
60-933-01
12 VDC, 2A Desktop power supply with
orange captive screw attached (for use
with DVI DA4 Plus)
28-181-05LF
12 VDC, 3A Desktop power supply with
orange captive screw attached (for use
with DVI DA6 Plus and DVI DA8 Plus)
28-113-05LF
70-770-03
(1) IEC cord
(4) Rubber feet (not attached)
MBD 149 rack mount kit
(DVI DA6 Plus and DVI DA8 Plus only)
DVI DA Plus Series User's Manual
Accessories
Accessories
Part number
60-190-20
60-604-20
60-190-10
60-604-10
60-190-01
60-604-01
70-222-01
RSF 123 (3.5" deep, 1U rack shelf kit)
RSB 123 (3.5" deep, 1U basic rack shelf)
RSU 126 (6" deep, 1U rack shelf kit)
RSB 126 (6" deep, 1U basic rack shelf)
RSU 129 (9.5" deep, 1U rack shelf kit)
RSB 129 (9.5" deep, 1U basic rack shelf)
MBU 149 Under desk mounting kit
(for DVI DA6 Plus and DVI DA8 Plus)
MBU 125 Under desk mounting kit
(for DVI DA4 Plus only)
70-077-01
26-585-0x
26-584-0x
DVID SL series (3, 6 or 15 feet single link
DVI-D male to male patch cables)
IN9700 series (25, 35, 50 or 75 feet single
link DVI-D male to male long distance
extension cables)
DVI DA Plus Series • Reference Information
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non-
Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron USA - West Extron USA - East Extron EMEA
Extron Asia
Extron Japan
Extron China
Extron Middle East
Headquarters
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
Inside China Only
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
+1.714.491.1500
+1.714.491.1517 FAX
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|