User’s Manual
Do not connect this device to a computer data or
telecommunications network.
CAUTION
TP Transmitters Family
High Resolution Video, Composite Video, and Stereo Audio
Twisted Pair Cable Transmission Products
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
68-546-03 Rev. G
07 08
+81.3.3511.7655 FAX +81.3.3511.7656
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
ᅝܼ乏ⶹꢀꢀ噝ꢀꢀЁ᭛
䄺ਞ
⬉⑤ꢀ噝ꢀ䆹䆒া㛑Փ⫼ѻકϞᷛᯢⱘ⬉⑤DŽꢀ䆒ᖙ⫼᳝
ഄ㒓կ⬉㋏㒳կ⬉DŽϝᴵ㒓˄ഄ㒓˅ᰃᅝ䆒ᮑˈϡ㛑ϡ
⫼䏇䖛DŽ
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒⫼᠋
ݠ Ё ⱘ᪡㓈ᡸ䇈ᯢDŽ
ꢀ
ᢨᥝ⬉⑤ꢀ噝ꢀЎᅝܼഄҢ䆒ᢨᥝ⬉⑤ˈ䇋ᢨᥝ᠔᳝
ꢀꢀৢḠ䴶⬉⑤ⱘ⬉⑤㒓ˈӏԩ
ࠄ Ꮦ⬉㋏㒳 ꢀꢀ⬉⑤㒓DŽ
ꢀ䖭Ͼヺো䄺ਞ⫼᠋䆹䆒ᴎ
ݙ ᲈ ꢀ䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽ꢁ
⬉⑤㒓ֱᡸꢀ噝ꢀཹᏗ㒓ˈꢀ䙓
ܡ 㹿䏽䏣ˈ䞡⠽य़DŽ 㓈ᡸꢀ噝ꢀ᠔᳝㓈ׂᖙ乏⬅䅸䆕ⱘ㓈ׂҎਬ䖯㸠DŽꢀ䆒
ꢀꢀ䚼≵᳝⫼᠋ৃҹᤶⱘ䳊ӊDŽЎ䙓
ߎܡ ⦄㾺⬉ॅ ꢀꢀϡ㽕㞾Ꮕ䆩ᠧᓔ䆒Ⲫᄤ㓈ׂ䆹䆒DŽ
䗮亢ᄨꢀ噝ꢀ᳝ѯ䆒ᴎϞ᳝䗮亢ῑᄨˈᅗӀᰃ⫼
ꢀꢀ䰆ℶᴎ
ݙ ᬣᛳܗ ӊ䖛⛁DŽϡ㽕⫼ӏԩϰ㽓ᣵԣ䗮亢ᄨDŽ 䫖⬉∴ꢀ噝ꢀϡℷ⹂ⱘᤶ⬉∴Ӯ᳝⟚⚌ⱘॅ䰽DŽᖙ乏Փ
ꢀꢀϢॖᆊ㤤ⱘⳌৠⳌ䖥ൟোⱘ⬉∴DŽᣝ✻⫳ѻॖⱘ
⊼ᛣ
䯙䇏䇈ᯢкꢀ噝ꢀ⫼᠋Փ⫼䆹䆒ࠡᖙ乏䯙䇏ᑊ⧚㾷
ꢀꢀ᳝ᅝܼՓ⫼䇈ᯢDŽ
ֱᄬ䇈ᯢкꢀ噝ꢀ⫼᠋ᑨֱᄬᅝܼ䇈ᯢкҹᇚᴹՓ⫼DŽ
ꢀꢀ䙉ᅜ䄺ਞꢀ噝ꢀ⫼᠋ᑨ䙉ᅜѻક⫼᠋ᣛफϞⱘ᠔᳝
ꢀꢀᅝܼ᪡䇈ᯢDŽ
䙓
ܡ 䗑ࡴ ꢀ噝ꢀϡ㽕Փ⫼䆹ѻકॖଚ≵᳝㤤ⱘᎹ ꢀꢀ䗑
ࡴ 䆒ˈҹ䙓ܡ ॅ䰽DŽ ꢀꢀ䆂໘⧚ᑳᓗ⬉∴DŽ
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may
cause undesired operation. The Class A limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
N
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 • Introduction ..........................................................1-1
About the TP Transmitters ................................................1-2
Features ......................................................................................1-3
TP T 15HD A transmitter ....................................................... 1-3
TP T 15HD AV transmitter ..................................................... 1-4
TP T 468 transmitter .............................................................. 1-4
TP T BNC DA4 transmitter/distribution amplifier ................ 1-5
Chapter 2 • Installation and Operation ......................... 2-1
Installation................................................................................ 2-2
Overview ................................................................................ 2-2
Video jumpers ........................................................................ 2-3
Video DIP switch .................................................................... 2-5
Audio jumpers ....................................................................... 2-5
Mounting the TP T 15HD A, TP T 15HD AV, or
TP T BNC DA4 ......................................................................... 2-6
Tabletop use ..................................................................... 2-7
UL rack mounting guidelines .......................................... 2-7
Rack mounting procedure .............................................. 2-7
Under-desk mounting .................................................... 2-8
Through-desk mounting ............................................... 2-10
Installing the TP T 468 ......................................................... 2-11
TP T 468 installation overview ...................................... 2-11
UL guidelines for wall box installation ........................ 2-12
Euro Channel models..................................................... 2-12
Preparing the site and installing the mud ring or
wall box .......................................................................... 2-13
Mounting the AAP devices............................................ 2-16
Mounting the transmitter to the mud ring or
wall box .......................................................................... 2-17
Installing the Euro Channel transmitter....................... 2-18
Grounding the transmitter ................................................. 2-19
Input cabling ........................................................................ 2-20
Computer video and PC audio ...................................... 2-20
Composite video and stereo audio............................... 2-24
RGBHV video .................................................................. 2-24
Transmitted signal cabling .................................................. 2-25
Termination of TP cable ................................................ 2-26
Cable testing .................................................................. 2-26
Equalizing pair skew...................................................... 2-27
Power connector.................................................................. 2-28
Unique TP T 468 front panel features ................................ 2-29
Extron TP Transmitters • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
Front Panel Control and Indicators ............................ 2-29
TP Transmitters
Troubleshooting ................................................................... 2-30
If the image does not appear ............................................. 2-30
If the image is not displayed correctly ............................... 2-31
If the receiver’s Manual/Auto LED flashes.......................... 2-31
Appendix A • Specifications, Accessories, and
Part Numbers................................................................................... A-1
Specifications ......................................................................... A-2
Included Parts......................................................................... A-6
Accessories............................................................................... A-7
Cables and Adapters ........................................................... A-7
Optional Adapter Plates ................................................... A-8
TP T 468 Template ............................................................... A-12
Chapter One
1
Introduction
About the TP Transmitters
Features
All trademarks mentioned in this manual are the properties of their respective owners.
68-546-03 Rev. G
07 08
ii
Extron TP Transmitters • Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Each transmitted TP signal must be connected to the
About the TP Transmitters
appropriate Extron TP receiver. This user’s manual documents
the installation, features, and operation of the TP transmitters
only. For information about the TP receivers, refer to the TP
Receivers Family User’s Manual, which accompanies the receivers.
Extron’s Twisted Pair (TP) transmitters provide long-distance
distribution of RGB video, component video, S-video,
composite video, and stereo audio over Extron’s Skew-Free™
A/V UTP cable or standard Category (CAT) 5 unshielded
twisted pair (UTP), shielded twisted pair (STP), or foil shielded
twisted pair (FTP) cable.
The TP T 468 is mountable in a 4-gang mud ring or electrical
box installed in a wall or inset in furniture. It is also available in
Euro Channel (EC) versions (see appendix A for part numbers).
It has openings for four single space (single height) Extron
Architectural Adapter Plates (AAPs).
The minimum reliable transmission distance to all receivers,
with the exception of the TP R 15HD A, is 50 feet (15.2 meters).
There is no minimum distance for transmission to the
TP R 15HD A. The maximum distance is determined by the
output frequency and resolution. The following table specifies
the recommended maximum transmission distances using
Extron Skew-Free A/V UTP cable or UTP CAT 5 cable,
terminated with CAT 6, or at least CAT 5e, rated connectors.
Features
All Extron TP transmitters provide the following features:
Frequency range — Supports 15 kHz to 130 kHz horizontal
frequency.
Extron recommends using the highest quality cable
available and affordable. We also recommend the use of
pre-terminated and tested cables. Cables terminated on
site should be tested before use to ensure that they
comply with Category 5e specifications.
TP T 15HD A transmitter
Video input — Accepts computer analog video on a 15-pin HD
female connector. With an adapter cable, the transmitter
can accept Macintosh, 13W3 video, RGBHV, RGBS, RGsB,
component video, S-video, or single source composite
video input.
Recommended transmission ranges at 60 Hz to
TP R 15HD A
Buffered local monitor output — Allows you to view the
displayed image on a local monitor that is located up to
100 feet from the transmitter, without signal reflections or
crosstalk.
Video format
Composite video and audio
Component video and S-video
640 x 480
Maximum range
800' (245 m)
800' (245 m)
500' (150 m)
400' (120 m)
300' (90 m)
Audio input — Accepts PC audio on a 3.5 mm stereo mini jack.
800 x 600
1024 x 768
RJ-45 connector — Provides a connection to an Extron TP RGB
1280 x 1024
1600 x 1200
200' (60 m)
150' (40 m)
video receiver.
Horizontal shift — Allows you to adjust the horizontal
placement of the image on the screen. Also called
“horizontal centering”.
Recommended transmission ranges at 60 Hz to
all other receivers
Mounting — Can be rack mounted with Extron’s RSM 100 TP
Rack Mounting Kit (part #70-123-01) and RSU 129 1U, 9.5"
deep rack shelf (part #60-190-01) or RSB 129 1U, 9.5" deep
Basic Rack Shelf (part #60-604-02). It can also be furniture
mounted with Extron’s MBU 125 Under Desk Mounting
Kit (part #70-077-01) or MBD 129 Through Desk
Video format
Composite video and audio
Component video and S-video
640 x 480
800 x 600
1024 x 768
Maximum range
1000' (300 m)
1000 (300 m)
1000 (300 m)
800' (245 m)
600' (185 m)
400' (120 m)
300' (90 m)
Mounting Kit (part #70-077-02).
1280 x 1024
1600 x 1200
It is possible to exceed the recommended distances,
however, image quality may be reduced.
Extron TP Transmitters • Introduction
1-2
Extron TP Transmitters • Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
Horizontal shift — Allows you to adjust the horizontal
TP T 15HD AV transmitter
placement of the computer video image on the screen.
Video input
Choice of colors — The TP T 460/468 transmitters are available
with a choice of gray, black, or white front panels to
match any decor.
Computer video — Accepts computer analog video on a
15-pin HD female connector. With an adapter cable, the
15HD connector can accept a Macintosh video, 13W3
video, or RGBHV, RGBS, RGsB, component video,
S-video, or single source composite video input.
Mounting — Wall or furniture mounted in a four-gang wall
box. EC versions are available that are mountable in a
Euro Channel raceway.
Composite video — Accepts NTSC, PAL, and SECAM
composite video on an RCA jack. Alternately, the
composite video channel can support digital audio.
Adapter plate capable — Has openings for four single space
(single-height) Extron AAPs with pass-through
connectors.
Buffered local monitor output — Allows you to view the
displayed computer video image on a local monitor that
is located up to 100 feet from the transmitter, without
signal reflections or crosstalk.
TP T BNC DA4 transmitter/distribution amplifier
Video input — Accepts RGBHV, RGBS, RGsB, component
video, and composite video on BNC connectors. With an
adapter cable, the transmitter can also accept an S-video
input.
Audio input — Accepts PC audio on a 3.5 mm stereo mini jack,
and stereo audio on two RCA jacks.
RJ-45 connectors — One connector provides a connection to an
Extron TP RGB video receiver, and the other provides a
connection to a TP composite video receiver.
RJ-45 connectors — Allows connection to up to four Extron
TP RGB video receivers.
Mounting — Can be rack mounted with Extron’s RSM 100 TP
Rack Mounting Kit (part #70-123-01) and RSU 129 1U, 9.5"
deep rack shelf (part #60-190-01) or RSB 129 1U, 9.5" deep
Basic Rack Shelf (part #60-604-02). It can also be furniture
mounted with Extron’s MBU 125 Under Desk Mounting
Kit (part #70-077-01) or MBD 129 Through Desk
Horizontal shift — Allows you to adjust the horizontal
placement of the computer video image on the screen.
Mounting — Can be rack mounted with Extron’s RSM 100 TP
Rack Mounting Kit (part #70-123-01) and RSU 129 1U, 9.5"
deep rack shelf (part #60-190-01) or RSB 129 1U, 9.5" deep
Basic Rack Shelf (part #60-604-02). It can also be furniture
mounted with Extron’s MBU 125 Under Desk Mounting
Kit (part #70-077-01) or MBD 129 Through Desk
Mounting Kit (part #70-077-02).
Mounting Kit (part #70-077-02).
TP T 468 transmitter
Video input — Accepts computer analog video on a 15-pin HD
female connector. With an adapter cable, the transmitter
can accept a Macintosh, 13W3 , RGBHV, RGBS, RGsB,
component video, S-video, or composite video input.
Buffered local monitor output — Allows you to view the
displayed image on a local monitor that is located up to
100 feet from the transmitter, without signal reflections or
crosstalk.
Audio input — Accepts PC stereo audio on a 3.5 mm stereo
mini jack.
RJ-45 connector — Provides a connection to an Extron TP RGB
video receiver.
Extron TP Transmitters • Introduction
1-4
Extron TP Transmitters • Introduction
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
TP Transmitters
Chapter Two
2
Installation and Operation
Installation
Front Panel Control and Indicators
Troubleshooting
Extron TP Transmitters • Introduction
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
Connect power cords to the TP receiver, the TP
transmitter, and turn on the video source(s) and the
output display(s).
8
Installation
Installation and service must be performed by
authorized personnel only. The TP T 468 must be
used with a UL approved electrical box.
CAUTION
All TP transmitters include a 15 V external power
supply. The transmitters also receive power from the
associated Extron TP receiver(s) (with the exception of
the TP R 15HD A) via the TP cable. Extron
Overview
recommends using the local power supply; however, the
power supply may not be necessary in some applications.
To install and set up a TP transmitter and the associated TP
receiver(s) for operation, perform the following steps:
•
•
The TP T 15HD A, TP T 15HD AV, TP T 468, and
TP T BNC may not require a local power supply for
cable lengths of 300' (91 m) or less.
Disconnect power from all of the equipment, including the
video source(s) (such as computers or DVD players), the
transmitter, the receiver, and the output display(s).
1
2
The TP T BNC DA4 and any transmitter
connected to a TP R 15HD A always require the
local power supply.
For component, S-video, or composite video, reconfigure
the jumpers (TP T 15HD A, TP T 15HD AV, and TP T BNC
DA4) or DIP switch (TP T 468). See “Video jumpers” or
Video DIP switch,” later in this chapter.
If you encounter problems, use the local power supply.
Adjust the picture controls on the front panel of the
transmitter and receiver(s). See “Front Panel Control and
Indicator,” later in this chapter, and refer to the TP
Receivers Family User’s Manual.
TP T 15HD AV only — If desired, configure the audio
jumpers to make the transmitter compatible with
unmodified TP receivers. See “Audio jumpers,” later in
this chapter.
9
3
The TP T 15HD AV is a redesigned (modified)
transmitter. The audio jumpers configure the audio
portion of the composite video TP link to work with the
similarly redesigned TP R BNC AV receiver or with
older, unmodified receivers. Redesigned transmitters
and receivers have an identifying label.
TP T 468 only — Mount the transmitter into the mud ring
or electrical box. See “Mounting the AAP devices” and
“Mounting the transmitter to the mud ring or wall box” or
“Euro Channel transmitter installation,” later in this
chapter.
10
TP T 468 only — Restore power to the devices.
11
Mount the transmitter in a rack, under a desk or podium,
in a desk or table (TP T 15HD A, TP T 15HD AV, or
TP T BNC DA4) or in a wall (TP T 468). See “Mounting
the TP T 15HD A, TP T 15HD AV, or TP T BNC DA4” or
“Installing the TP T 468,” later in this chapter.
4
Video jumpers
The TP T 15HD A, TP T 15HD AV, TP T BNC, and
TP T BNC DA4 transmitters can be configured to transmit
component video, S-video, or composite video.
Connect the input cables. See “Input cabling,” later in this
chapter.
5
6
The transmitters are factory configured for RGB video.
For any other type of video, reconfigure the jumpers.
Connect the cable(s) between the transmitter and the TP
receiver(s). See “Transmitted signal cabling,” later in this
chapter and refer to the TP Receivers Family User’s Manual.
1.
Remove the two screws on each side and the screw on top
of the cover (figure 2-1).
Configure the TP receiver(s). Refer to the TP Receivers
Family User’s Manual.
7
Extron TP Transmitters • Installation and Operation
2-2
Extron TP Transmitters • Installation and Operation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
TP T 15HD A
TP T BNC DA4
Video DIP switch
Remove 5 BNC hex nuts.
Remove 6
screws.
The TP T 468 can be configured to transmit component video,
Lift cover
straight up.
S-video, or composite video. To configure the TP T 468
for RGB video, set DIP switch 2 on the back of the
transmitter to Off. For any other video format set the
switch to On.
Component,
S-video,
A
UDIO
COMPUTER
1
1
1
1
IDPN4
I
B
U
FFERED
Composite
IT
H-SHIFT
RGB
1
1
1
1
OR
1
1
1
1
TP
T
15HD
A
1
1
1
1
Component, RGB
S-video,
Composite
Audio jumpers
J1
J2
Older (unmodified) transmitters and receivers are fully
compatible with each other but not with the TPX 88 A
twisted pair matrix switcher.
J12
J11
Redesigned (modified) transmitters and receivers are
fully compatible with each other and with the TPX 88 A.
They can also be jumpered to be compatible with the
older (unmodified) receivers and transmitters but not
the TPX 88 A.
U31
TP T BNC DA4
TP T 15HD A and TP T 15HD AV
Figure 2-1 — Video jumper configuration
Redesigned (modified) transmitters and receivers have an
identifying label.
2.
TP T BNC DA4: Using an Extron BNC extraction tool (part
#100-096-01) or a 14 mm, deep well socket with thin walls,
remove the five hex nuts securing the BNC connectors to
the rear panel. Slide the cover forward until the cover
clears the BNC connectors
The audio that is associated with the composite video link of
TP T 15HD AV transmitters is transmitted on wire pair 3 and 6.
This configuration is compatible with redesigned TP receivers
and the TPX 88 A.
If you intend to match this transmitter with an older,
unmodified TP receiver, and do not plan to include a TPX 88 A
in your system, you can set the transmitter to send the audio on
wire pair 7 and 8, to be compatible with an older TP receiver, by
shifting internal jumpers as follows:
3.
4.
Lift the cover off.
TP T 15HD A and TP T 15HD AV: Locate J1 and J2 on the
printed circuit board. See figure 2-1.
a.
For RGB video, ensure that pin 2 is jumpered to
pin 3 on both jumper locations.
b.
For any other video format, ensure that pin 1 is
jumpered to pin 2 on both jumper locations.
TP T BNC DA4: Locate J11 and J12 on the printed circuit
board. See figure 2-1.
a.
For RGB video, ensure that pin 2 is jumpered to
pin 3 on both jumper locations.
b.
For any other video format, ensure that pin 1 is
jumpered to pin 2 on both jumper locations.
5.
Replace the cover and reinstall the screws.
Extron TP Transmitters • Installation and Operation
2-4
Extron TP Transmitters • Installation and Operation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
1.
Remove the two screws on each side and the screw on top
of the cover (figure 2-2).
Tabletop use
Four self-adhesive rubber feet are included with the unit. For
tabletop use, affix one foot at each corner of the bottom of the
transmitter, and place the unit in the desired location.
Remove (5)
Screws
TP T 15HD AV
Wire Pair Wire Pair
3&6*
7&8
UL rack mounting guidelines
Lift Cover
straight up
The following Underwriters Laboratories (UL) guidelines
pertain to the safe installation of the equipment in a rack.
A
U
DIO
J6
J7
COMPUTER
ID PIN
4
ID PIN 11
B
U
FFERED
IT
PC
H-SHIFT
O
VIDEO
1.
Elevated operating ambient temperature — If the
equipment is installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack
environment may be greater than room ambient
temperature. Therefore, install the equipment in an
environment compatible with the maximum ambient
temperature (Tma = +113 °F, +45 °C) specified by Extron.
AU
L
D
I
O
TP
T
15HD
A
R
V
TP T 15HD AV
2.
3.
4.
Reduced air flow — Install the equipment in a rack so that
the amount of air flow required for safe operation of the
equipment is not compromised.
* TPX compatible
Figure 2-2 — Audio jumper configuration
Mechanical loading — Mount the equipment in the rack
so that a hazardous condition is not achieved due to
uneven mechanical loading.
2.
3.
Lift the cover off.
Locate J6 and J7 on the printed circuit board. See figure 2-2.
a.
For compatibility with redesigned (modified)
receivers and the TPX 88 A, ensure that pin 1 is
jumpered to pin 2 on both jumper locations.
Circuit overloading — Connect the equipment to the
supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Also consider equipment nameplate
ratings when addressing this concern.
b.
For compatibility with older (unmodified)
receivers, ensure that pin 2 is jumpered to pin 3 on
both jumper locations.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).
4.
Replace the cover and reinstall the screws.
Mounting the TP T 15HD A, TP T 15HD AV, or
TP T BNC DA4
Rack mounting procedure
The TP T 15HD A, TP T 15HD AV, and TP T BNC DA4
transmitters can be set on a table; mounted on a rack shelf; or
mounted through or under a desk, podium, or tabletop. The
following optional mounting kits are available for the series:
To mount the transmitter on a 9.5" deep rack shelf,
1.
If rubber feet were previously attached to the bottom of
the unit, remove them.
2.
Fit the RSM 100 mounting bracket around the transmitter
and attach it to the unit using one mounting hole on each
end.
•
•
•
RSM 100 TP rack mounting kit (#60-604-02)
RSB 129 1U, 9.5" deep basic rack shelf (#60-604-02)
RSU 129 1U, 9.5" deep rack shelf kit (#60-190-01)
3.
4.
Mount the bracket containing the unit onto the rack shelf,
using two 4-40 x 3/16" screws in the two mounting holes
in the bottom of the bracket to secure it.
•
MBU 125 under-desk mounting bracket kit (#70-077-01)
MBD 129 through-desk mounting bracket kit (#70-077-02)
Install blank panel(s) or other unit(s) on the rack shelf as
desired.
•
Extron TP Transmitters • Installation and Operation
2-6
Extron TP Transmitters • Installation and Operation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
5.
Attach the rack shelf to the rack using the supplied bolts.
To mount the transmitter under a desk, podium, or table top,
1.
2.
3.
If rubber feet were previously attached to the bottom of
the unit, remove them.
1U Universal Rack Shelf
Remove the two screws from one side of the unit. Retain
the screws for possible later reassembly.
Attach one bracket to the side of the unit, using the
provided machine screws.
4.
5.
Repeat steps 2 and 3 on the other side of the unit.
Hold the unit with the attached brackets against the
underside of the table or other furniture. On the mounting
surface, mark the location of the bracket’s screw holes.
6.
Drill pilot holes 1/4" (6.4 mm) deep and 3/32" (2 mm) in
diameter into the table or desk top at the marked screw
locations. The holes should be drilled from the underside
or inside (concealed side) of the furniture where the
transmitter will be located.
(2) 4-40 x 3/16"
Screws
7.
8.
9.
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until slightly less
than 1/4" of the screw head protrudes.
Use 1 mounting hole on each side of
the unit to attach it to the RSM 100.
Use 2 mounting holes on the bottom of
the RSM 100 to attach it to the shelf.
Align the mounting screws with the slots in the brackets
and place the unit against the surface, with the screws
through the bracket slots.
Figure 2-3 — Rack mounting a TP T series transmitter
Under-desk mounting
Slide the unit slightly forward or back, then tighten all
four screws to secure it in place.
Furniture-mount the transmitter under a desk or shelf using the
optional mounting kit (part #70-077-01), as illustrated below.
Figure 2-4 — Under-desk mounting the transmitter
Extron TP Transmitters • Installation and Operation
2-8
Extron TP Transmitters • Installation and Operation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Through-desk mounting
c.
Tighten the screws.
Mount the transmitter through a desk or table, using the
optional through-desk mounting kit (part #70-077-02).
d.
Replace the unit inside the surface (repeat step 4).
Installing the TP T 468
TP T 468 Installation Overview
To install a TP T 468 transmitter, follow these steps:
Disconnect power from all of the equipment, including the
video source(s) (such as computers or DVD players), the
transmitter, the receiver, and the output display(s).
1
2
For non-Euro Channel (EC) versions, prepare the site: cut
a hole in the wall/furniture, install the electrical box or
mud ring, and prepare the cables. Instructions are
included in this manual and/or with the wall box. See
“Preparing the site and installing the mud ring or wall
box,” later in this chapter.
For the EC versions, see “Euro Channel transmitter
installation,” later in this chapter.
Connect the input cables. See “Input cabling,” later in this
chapter.
3
4
Connect the cable(s) between the transmitter(s) and the TP
receiver(s). See “Transmitted signal cabling,” later in this
chapter , and refer to the TP Receivers Family User’s
Manual, part #68-547-01.
Figure 2-5 — Through-desk mounting the transmitter
1.
2.
3.
Mark the opening through which the unit will be
mounted — approximately 1.2" by 6.9" (3.0 cm by 17.5 cm).
Configure the TP receiver(s). Refer to the TP Receivers
Family User’s Manual, part #68-547-01.
5
6
Cut out the material from the installation area with a
jigsaw.
Connect power cords to the TP receiver(s), the TP
transmitter(s) (if applicable), and turn on the video
source(s) and the output display(s).
Drill pilot holes 1/4" (6.4 mm) deep and 3/32" (2 mm) in
diameter in the desk or table at the locations of the
mounting bracket screws. The holes should be drilled
from the underside or inside (concealed side) of the
furniture where the transmitter will be located.
The TP T 468 includes a 15 VDC external power supply.
The transmitter also receives power from the associated
Extron TP receiver via the TP cable. Extron
recommends using the local power supply; however, the
TP T 468 may not require a local power supply for cable
lengths of 300’ (91.4 m) or less. If problems are
encountered, use the local power supply.
4.
5.
Using the four provided wood screws, attach the brackets
to the mounting surface.
Slide the unit up and down or back and forth in the
mounting brackets until the front panel of the unit is at the
desired height. Tighten the screws that secure the bracket
in place.
Adjust the picture controls on the front panel of the
transmitter and receiver. See Front Panel Control and
Indicators, later in this chapter, and refer to the TP
Receivers Family User’s Manual, part #68-547-01.
7
8
If the screws are inaccessible to a screwdriver,
a.
Mark the location of the brackets relative to the
screws.
Disconnect power from all the devices.
b.
Remove the transmitter from inside the furniture.
Extron TP Transmitters • Installation and Operation
2-10
Extron TP Transmitters • Installation and Operation
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Install the desired AAPs on the transmitter. See
Preparing the site and installing the mud ring or wall box
9
“Mounting the optional AAP devices,” later in this
chapter.
The TP T 468 is mounted into a wall or furniture. Follow the
instructions appropriate to the mounting option you have
selected. Templates for optional faceplates are not included in
this manual.
Mount the transmitter into the electrical box or to the mud
ring. If using a wall box, see “Mounting the transmitter to
the mud ring or wall box,” later in this chapter.
10
11
The transmitter must be installed into an
CAUTION
Underwriters Laboratories (UL) approved electrical
wall box.
Restore power to the devices.
UL guidelines for wall box installation
Choose a location that allows cable runs without interference.
Allow enough depth for both the wall box and the cables. You
may need to install the cables into the wall, furniture, or
conduits before installing the transmitter.
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the TP T 468 into a wall or furniture
(figure 2-6).
The installation must conform to national and local electrical
codes and to the equipment’s size requirements. An actual-size
cut-out template is provided in appendix A of this manual.
Installation
Cable
Conduit
Installation using a UL listed wall box (available from Extron) is
recommended for most mounting options, but the included
mud rings can be used instead. All wall boxes must be at least
2.5" (6.4 cm) deep.
HIFT
S
H.
Before using the mud rings, verify that the installation
conforms to national and local electrical codes.
MONITOR
8
46
TP T
MIN/MAX
INPUT
R
ITO
N
O
M
O
N
R
O
1.
Select and cut out the appropriate template for your
installation type:
IT
N
O
M
AUDIO
•
If you are using a mud ring, use the template
provided with the mud ring. Cut out the indicated
center portion.
2.5"
TP T 468
Figure 2-6 — TP T 468 in a four-gang wall box
•
If you are using a wall box, cut out or make a 100%
size photocopy of the template in appendix A that
corresponds to the faceplate you are using, and cut
out the center portion as indicated on the template.
1.
This unit is not to be connected to a centralized DC power
source or used beyond their rated voltage range.
2.
3.
This unit must be installed in UL listed junction boxes.
2.
Place the template (or the wall box or mud ring) against
the installation surface, and mark the guidelines for the
opening on the wall or furniture.
This unit must be installed with conduit in accordance
with the National Electrical Code.
3.
4.
Cut out the wall or furniture material from the marked
area.
Euro Channel models
The TP T 468 is available in a Euro Channel (EC) version (see
appendix A for part numbers).
Check the opening size by inserting the wall box, mud
ring, or transmitter into the opening. The box or mud ring
(if used) and/or transmitter should fit easily into the
opening. Enlarge or smooth the edges of the opening if
needed.
The front and rear panel features, cabling requirements, and
testing/troubleshooting procedures are identical to the
descriptions shown in chapter 2, Installation and Operation, for
the non-EC models. See Euro Channel transmitter installation in
this appendix for the EC transmitter model installation
instructions.
Extron TP Transmitters • Installation and Operation
2-12
Extron TP Transmitters • Installation and Operation
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
5.
If you are using a wall box, feed cables through the wall
box punch-out holes, and secure them with cable clamps
to provide strain relief.
7.
If you are using a mud ring, follow the directions, if any,
that came with the mud ring to attach the clips that fasten
it to the wall or furniture (figure 2-8).
6.
Exposed cable shields (braids or foil) are potential sources
of short circuits. Trim back and/or insulate shields with
heat shrink (figure 2-7).
Sheet Rock
Backing Clip
Wall Stud
0.75" #6-32
Screw
Mounting Bracket
Detail A
Screws or Nails
Sheet Rock
Backing Clip
Cable
Clamp
H. SHIFT
1.25" #6-32
Screw
MONITOR
INPUT
468
TP
T
MIN/MAX
Mounting Bracket
MONITOR
MONITOR
Detail B
Extron
AUDIO
TP T 468
Backing Clip can
be in either orientation.
See Detail A or Detail B.
Foil
Shield
Installation
Cable
Braided
Shield
Figure 2-8 — Attaching a mud ring to a wall
Screw
If you are using a wall box, insert the wall box into the
opening, and attach it to the wall stud/furniture with nails
or screws, leaving the front edge flush with the outer wall
or furniture surface (figure 2-9).
Figure 2-7 — Grounding outer braided and foil
shields
If attaching the wall box to wood, use four #8 or #10
screws or 10-penny nails. A minimum of 1/2 inch (1.3 cm)
of screw threads must penetrate the wood.
To prevent short circuits, cut back the outer foil
shield to the point where the cable exits the cable
clamp. Both braided and foil shields should be
connected to an equipment ground at the other end
of the cable.
If attaching the wall box to metal studs or furniture, use
four #8 or #10 self-tapping sheet metal screws or machine
bolts with matching nuts.
Extron TP Transmitters • Installation and Operation
2-14
Extron TP Transmitters • Installation and Operation
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
#4-40 Nut w/ Captive
Washer
Wall Stud
Wall Box
4-gang Wall Box
HIFT
S
H.
R
8
46
MONITO
INPUT
TP
T
MIN/MAX
Flush with
Wall Surface
R
O
IT
N
O
M
R
O
IT
N
O
M
Screws or Nails
AUDIO
Figure 2-9 — Attaching a wall box to a wall
stud
TP T 468
Figure 2-10 — Mounting an AAP
8.
Cable and install the desired AAPs, set the Composite/
RGB and DDSP DIP switches, and cable and test the
transmitter before fastening the transmitter into the wall
box. See Input cabling, later in this chapter, for details.
3.
Attach the output cables to the rear connectors of the
adapter plates. Soldering will be required for some
connectors. Attach foil and braided shields to ground
connections.
The AAPs, switches, and cable are inaccessible after
installation.
Mounting the transmitter to the mud ring or wall box
1.
Remove power from the interface by disconnecting the
power supply.
Mounting the AAP devices
The TP T 468 faceplates accept up to four optional single height
Extron Architectural Adapter Plates (AAPs). The adapter plates
allow for a variety of connectors.
2.
Place the interface through the opening in the wall or
furniture and into the wall box. Take care not to damage
the cables, which fit behind the interface, at the back of the
wall box.
Blank plates (two single-space and one double-space plate) are
included on the transmitter to cover unused spaces. Adapter
plates must be ordered separately. They also must be attached
to the faceplate and cabled before the interface is installed in the
wall or furniture (figure 2-10). The screws needed for installing
the adapter plates are built into the plates, so no additional
screws are needed.
3.
Mount the interface’s faceplate to the mud ring or wall box
with machine screws (figure 2-11 on the next page).
1.
Remove the blank plates from the interface by unscrewing
the nuts that fasten the plates to the faceplate.
2.
Insert the adapter plate screws through the holes in the
faceplate. Attach the adapter plates to the faceplate with
the provided captive washers and #4-40 nuts.
Extron TP Transmitters • Installation and Operation
2-16
Extron TP Transmitters • Installation and Operation
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
HIF
S
H.
MIN/MAX
MO
460
INPU
TP
T
R
AUDIO
O
IT
N
O
R
O
IT
ON
O
M
N
M
Cable
Clamp
Installation
Cable
HIFT
S
H.
8
46
MONITOR
TP
T
MIN/MAX
INPUT
MONITOR
MONITOR
Euro Channel
AUDIO
Figure 2-12 — Mounting the transmitter in a Euro
Channel
TP T 468
Figure 2-11 — Mounting the transmitter to the wall
box
Grounding the transmitter
4.
Reconnect the power supply and restore power to the
equipment.
RGB and computer video transmitters may need to be grounded
to ensure that the video and audio are not degraded. The
TP T 15HD A, TP T 15HD AV, and TP T 468 may require
grounding if all of the following conditions are true:
Installing the Euro Channel transmitter
Once the EC transmitter has been cabled and tested, the
transmitter can be installed in the Euro Channel.
•
•
•
The signal source is a laptop computer.
No local monitor is connected.
1.
Remove power from the interface by disconnecting the
power supply.
A local power supply is not being used.
2.
Mount the interface to the Euro Channel by attaching the
faceplate to the two mounting brackets using the four #4-
40 mounting screws (figure 2-12).
Grounding may also be required if there is no common ground
in the power distribution system.
Indications that grounding may be required include:
•
•
•
The receiver’s Power LED is lit amber when a connection
is made to the transmitter.
The receiver is in auto mode and its Manual/Auto LED
flashes.
The receiver is in manual mode and an image appears
only when the Peaking adjustment is at the minimum
level. Additionally, the image may be overpeaked with
horizontal streaking to the right of displayed information.
•
No audio, or distorted and noisy audio, is heard.
Extron TP Transmitters • Installation and Operation
2-18
Extron TP Transmitters • Installation and Operation
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
2
1
4
3
Ground the transmitter using any of the following methods:
ID PIN
4
ID PIN 11
•
•
•
Connect a local 15 V power supply to the transmitter.
Use STP rather than UTP cable and connectors.
COMPUTER
BUFFERED
H-SHIFT
AUDIO
INPUT
LOCAL MONITOR
TP T 15HD A
TP T 15 HD A and TP T 15HD AV — Use a 3.5 mm
captive screw connector to connect a ground wire
between the power return pin (figure 2-13) and a
grounding point near the transmitter, such as a grounded
power outlet or an equipment rack.
11
9
5
POWER
15V .5A DC
•
TP T 468 only — Connect a ground wire between the
power return pin (figure 2-13) of the 3.5 mm, 2-pole
direct-insertion captive screw connector on the rear of the
transmitter and a grounding point near the transmitter.
OUTPUT
Figure 2-14 — Installation features, TP T 15HD A
TP T 15HD A and
TP T 15HD AV
2
1
4
3
6
7
TP T 468
ID PIN
4
ID PIN 11
AUDIO
L
VIDEO
PC
H-SHIFT
COMPUTER
BUFFERED
AUDIO
R
N/C
INPUT
LOCAL MONITOR
Return
TP T 15HD AV
Grounding Point
near Transmitter
11
10
9
5
Figure 2-13 — Grounding the transmitter
POWER
15V .5A DC
Input cabling
AV
COMPUTER
OUTPUTS
Computer video and PC audio
Figure 2-15 — Installation features, TP T 15HD AV
The TP T 15HD A (figure 2-14), the TP T 15HD AV
(figure 2-15), and the TP T 468 (figure 2-16) all accept and
transmit computer video and PC audio. These transmitters can
also accommodate component video, S-video, or composite
video if input on the R, G, and B pins of the 15HD connector
using an Extron SYM BNCF/0.5 6" (15 cm) cable,
part #26-531-01.
Extron TP Transmitters • Installation and Operation
2-20
Extron TP Transmitters • Installation and Operation
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
10
5
1
6
Computer Input connector — Connect a
computer video source to this 15-pin HD
female connector.
1
15
11
Female
13
Input only sync signals, no video
H. SHIFT
MONITOR
signals, on the sync pins (pins 13 and 14).
3
INPUT
For component video, use the R (R-Y) and R return pins
(pins 1 and 6), G (Y) and G return pins (pins 2 and 7),
and B (B-Y) and B return pins (pins 3 and 8).
MIN/MAX
NO MONITOR
4
MONITOR
AUDIO
For S-video, use the R, R return (C-chroma), G, and G
return (Y-luma) pins.
For composite video, use the G pin and the associated
return pin. For additional genlocked video signals, use
the R, B, and associated return pins.
TP T 468
2
1
14
5
15
Audio input connector — Connect PC audio to this 3.5 mm,
2
stereo jack. Wire the male plug as shown in figure 2-17.
Input only analog, line level, audio signals on the audio
input connector.
Tip (L)
Ring (R)
Sleeve (
)
Figure 2-17 — Audio input wiring
Buffered Local Monitor output connector — Connect a local
monitor video cable to this 15-pin HD female connector.
3
4
12
10
Figure 2-16 — Installation features, TP T 468
ID bit switches (TP T 15HD A and TP T 15HD AV) — If a local
monitor is installed, set both switches to off. If no local monitor
is installed, set both switches to on.
Transmission of component video, S-video, or composite video
on the computer video input requires that internal jumpers
(TP T 15HD A and TP T 15HD AV) or a DIP switch (TP T 468) be
reconfigured. See “Video jumpers,” or “Video DIP switch,”
earlier in this chapter.
DDSP switch — This switch turns on Digital Display Sync
Processing, disabling sync processing for LCD projectors and
other displays that cannot tolerate processed sync.
5
DDSP disables the horizontal shift control.
Extron TP Transmitters • Installation and Operation
2-22
Extron TP Transmitters • Installation and Operation
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Composite video and stereo audio
For component video, use the R (R-Y), G (Y), and B (B-Y) BNCs.
The TP T 15HD AV (figure 2-15) accepts and transmits
composite video and stereo audio.
R
G
B
H/HV
V
RGB/video switch (TP T 468 only) — Configures the
transmitter for RGB or component/S-video/composite video.
See “Video DIP switch,” earlier in this chapter.
6
For S-video, use the R (C-chroma) and G (Y-luma) BNCs.
R
G
B
H/HV
V
Video connector — Connect composite video to this RCA
connector. Digital audio can also be connected to this connector.
7
8
For composite video, use the G BNC. For three separate
genlocked video signals, use the R, G, and B BNCs.
Audio input connectors — Connect left and right stereo audio
to these RCA connectors.
R
G
B
H/HV
V
Input only analog, line level audio signals on these
connectors.
-or-
-or-
The TP T 15HD AV is backwards compatible with the
RGBHV video
The TP T BNC DA4 (figure 2-18) accepts and transmits RGBHV,
RGBS, RGsB, component video, S-video, and composite video.
TP T 15HD A and the TP T BNC DA4.
However, the TP T 15HD A and the TP T BNC DA4
(products whose part numbers end in -02) are not
forward compatible with the TP T 15HD AV (whose
part number ends in -03).
11
8
9
9
9
9
R
G
B
H/HV
V
Transmitted signal cabling
POWER
15V .5A DC
CAUTION
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4
Do not connect this device to a computer data or
telecommunications network
INPUT
Figure 2-18 — Installation features, TP T BNC DA4
RJ-45 termination must comply with the
TIA/EIA T 568A wiring standards for all connections.
Video connector — Connect the desired video input device to
the rear panel input BNCs. Transmission of component video,
S-video, or composite video requires that internal jumpers be
reconfigured. See “Video jumpers,” earlier in this chapter.
9
RGB video transmission connector — Attach one end of a TP
cable to this RJ-45 female connector. Attach the other end to an
Extron TP BNC receiver.
10
11
Composite video transmission connector — Attach one end of
a TP cable to this RJ-45 female connector. Attach the other end
to an Extron TP composite video receiver.
Input only sync signals (no video signals) on the H/V
and V BNCs.
For RGBHV video, use the R, G, B, H/HV, and V BNCs.
R
G
B
H/HV
V
For RGBS video, use the R, G, B, and H/HV BNCs.
R
G
B
H/HV
V
Extron TP Transmitters • Installation and Operation
2-24
Extron TP Transmitters • Installation and Operation
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Termination of TP cable
The Microtest OMNI SCANNER 2 performs comprehensive
certification testing to the CAT 6 standards. Other
manufacturers also make testing equipment. The tests include
advanced diagnostics for troubleshooting the cause and location
of many cable and termination problems. For simple
installation testing, the Microtest MICRO SCANNER PRO tests
wire map and cable length, including individual cable pair
length.
Figure 2-19 details the recommended termination of TP cables in
accordance with the TIA/EIA T 568A wiring standards.
Pins:
12345678
RGB video and audio AV video and audio
Pin Wire color
Signal
Level
0.35V
0.35V
Signal Level
1
2
White-green Red/V. sync+
Video+
Video–
+0.35V
–0.35V
Green
Red/V. sync–
Audio and
power
+15V with Audio+* &
+15V
Equalizing pair skew
3
White-orange
0.5 V
power+
The manufacturing process for network (CAT 5e) UTP cable
leads to a condition called pair skew. For best results, pair skew
needs to be equalized when using the CAT 5e cable in A/V
applications. The design of Extron’s Skew-Free A/V UTP cable
minimizes pair skew to the point that equalization is not
required.
4
5
Blue
Green+
Green–
+0.35V
Reserved None
Reserved None
White-blue
–0.35V
Audio and
power
Audio–* &
power–
Side View
6
Orange
0.5 V
0V
Insert
twisted
pair wires.
7
White-brown Blue/H. sync+ 0.35V
Brown Blue/H. sync– 0.35V
Reserved None
8
Reserved None
Skew exists between pairs when the physical length of one wire
pair is different from another. As the transmission cable length
increases, the amount of skew increases. Skew affects the
displayed image when the differential length between wire
pairs exceeds 2' (61 cm), causing the timing of the red, green,
and blue video signals to appear out of alignment (horizontal
registration errors). A white vertical line on a black field can
appear as individual red, green, and blue lines that are close
together; the signal transmitted on the shortest wire pair leads
the other colors and appears to the left on the display.
* Audio can be jumpered to wire pair 7 and 8.
See “Audio jumpers,” earlier in this chapter.
RJ-45 Connector
Figure 2-19 — TP cable termination
Cable testing
To ensure proper cable termination, each transmission cable
system that uses CAT 5e or CAT 6 cable should be tested
(Extron’s Skew-Free UTP cable does not need to be tested).
Testing the cable from the RJ-45 connections at the transmitter
and receiver gives the most accurate indications of cable
problems.
UTP cable test equipment measures and reports wire pair
length. The report on the various pair lengths can be used in
equalizing pair skew. The nominal velocity of propagation
(NVP — the speed at which the signal travels on the
transmission line, measured as a percentage of the speed of
light) of TP cable is very close to that of conventional coaxial
cable. The similarity in NVP means that an additional length of
coax equal to the length of pair skew, placed on the receiver’s
output, equalizes the effects of pair skew (figure 2-20).
There are two varieties of cable runs: simple runs, in which a
single cable is terminated only at the transmitter and receiver,
and complex runs, which can include patch bays and multiple
terminations and lengths of cable. In either case, the entire
cabling system should be tested.
A complete test measures cable length and tests the wire map,
attenuation, NEXT, PSNEXT, ELFEXT, PSELFEXT, return loss,
ACR and PSACR. All of these tests are critical for digital data
transfer. While all of these tests are important indicators of the
quality of the cable termination, the most critical testing
parameters for video transfer are wire map (T-568-A
termination) and pair length measurements. The largest
concern is equalization of skew between cable pairs. Cable
systems of 300' (91.4 m) or less should exhibit no transmission
problems if they pass at least CAT 5e or preferably CAT 6-D5
channel certification testing.
Extron TP Transmitters • Installation and Operation
2-26
Extron TP Transmitters • Installation and Operation
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
TP T 15HD A
Unique TP T 468 front panel features
IF cable measurement
indicates that the pair
with wires 1 and 2 is
four feet shorter than
the other pairs...
Faceplate screws — These screws secure the faceplate to the rest
13
A
UDIO
COMPUTER
IDPN4
1
of the transmitter.
B
UFFERED
T
H-
S
HIFT
O
R
Audio
TP
T
Do not remove these faceplate screws while the
transmitter is attached to the wall or the detached
transmitter circuit board may fall down inside the wall.
15HD
A
ER
DC
OW
P
V
.5A
15
R
IO
B
L
UD
A
Opening for Architectural Adapter Plates — The TP T 468 can
have up to four optional adapter plates attached here at one
time. The adapter plates allow for a variety of connectors.
A
14
YCN
O
V
T
TP R BNC A
O
B
G
R
UT
P
IN
GB
R
Blank plates (two single-space and one double-space plate) are
included on the transmitter to cover unused spaces. Adapter
plates must be ordered separately. They also must be attached
to the faceplate and cabled before the interface is installed in the
wall or furniture. See “Mounting the AAP devices,” earlier in
this chapter.
PC Computer
CAT 5 UTP Cable
Pair RGB video
1, 2 Red
... THEN insert a four foot
extension cable to equalize
TP skew for red video.
LCD Projector
4, 5 Green
7, 8 Blue
Front Panel Control and Indicators
Figure 2-20 — Pair skew equalization
All of the transmitters have front panel Power indicators. In
addition, the TP T 15HD A and TP T 15HD AV have horizontal
shift control.
If UTP cable test measurement cannot be done, pair skew can
still be equalized by viewing a test pattern with a critical eye.
Examine the test pattern for loss of horizontal registration and,
through a process of trial and error, equalize any pair skew with
coax extensions on the red, green, and/or blue outputs.
1
2
PC
AUDIO
COMPUTER
INPUT
ID PIN
4
ID PIN 11
BUFFERED
VIDEO
H-SHIFT
AUDIO
L
R
Extron skew compensation coax cables are available in lengths
of 2 through 20 feet (61 cm through 6.1 meters). See appendix A
for part numbers.
LOCAL MONITOR
TP T 15HD AV
Figure 2-21 — TP T 15HD AV control and indicator
Power connector
Power/signal LED
1
2
Power
TP T BNC DA4 — Plug the external 15V power supply
12
Amber — Indicates that power is applied, but that the
transmitter is not connected to a receiver.
into this captive screw connector.
Green — Indicates that the transmitter is properly connected to
If the distance between the transmitter and receiver is too
great for the receiver to power the transmitter, the video
image will be missing, distorted, or noisy, or the
receiver’s Manual/Auto LED will flash. The transmitter
requires a local 15V power supply.
a receiver.
H. Shift control (TP T 15HD A and TP T 15HD AV) — This
front panel knob adjusts the side-to-side image placement.
The H. Shift control is a 12-turn potentiometer with a soft
mechanical stop at the high or low end. When you have
reached the high or low end of the adjustment, the
potentiometer makes a clicking sound as you turn it, and no
change is apparent on the display.
TP T 15HD A and TP T 15 HD AV— If desired or for
distances over 300' (91.4 m), plug an external 15 VDC
power supply into this captive screw connector. Wire
the connector as shown at left.
N/C
+15V
Return
Extron TP Transmitters • Installation and Operation
2-28
Extron TP Transmitters • Installation and Operation
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
10. For computer video from a laptop or for ungrounded AC
distribution systems, the transmitter may need to be
grounded. See “Grounding the transmitter,” earlier in this
chapter.
Min/Max LED (TP T 468 only) — This front panel LED blinks
red momentarily whenever the minimum or maximum limits of
the horizontal shift control ( ) have been reached. Continually
turning the horizontal shift control knob in the same direction
after the limit has been reached will cause the LED to
continually blink.
3
2
11. Call the Extron S3 Sales & Technical Support Hotline if
necessary.
For details on the ID bit (TP T 15HD A and
TP T 15HD AV) or Monitor/No Monitor (TP T 468)
and DDSP switches, see “Computer video and PC
audio,” earlier in this chapter.
If the image is not displayed correctly
1.
For computer/RGB video, if the output image looks too
green, ensure that the receiver’s SOG switch is off.
2.
For computer video, if the picture hangs off the edge of the
screen, adjust the transmitter’s H Shift control.
Troubleshooting
DDSP disables the horizontal shift control.
If the image does not appear
3.
Place the receiver’s Manual/Auto switch to manual and
adjust the level and peaking controls for optimum quality.
1.
Ensure that all devices are receiving power. The
transmitter’s and receiver’s front panel Power LEDs
indicate that they are receiving power.
4.
The transmission distance may be too far for remote
power. Try connecting the local 15VDC power supply to
the transmitter.
2.
3.
Ensure that the transmitter is receiving a video input.
Ensure that the TP cable(s) are properly terminated in
accordance with TIA/EIA T 568A standards and that the
RJ-45 connections are securely made. If the Power LEDs
on the transmitter and the receiver are lit green, a
transmitter is properly connected to a receiver.
5.
6.
For computer video from a laptop or for ungrounded AC
distribution systems, the transmitter may need to be
grounded. See “Grounding the transmitter,” earlier in this
chapter.
If the image still does not display properly, call the Extron
S3 Sales & Technical Support Hotline. (See the rear cover
of this manual for the phone number for your region of the
world.)
4.
For computer/RGB video, ensure that the receiver’s SOG
and C Sync switches are in the correct positions for the
video output.
5.
6.
7.
For computer video, ensure that the transmitter’s ID bit
switches are on.
If the receiver’s Manual/Auto LED flashes
For computer video on an LCD projector, ensure that the
transmitter’s DDSP switch is on.
1.
The transmission distance may be too far for remote power.
Connect the local 15VDC power supply to the transmitter.
The transmission distance may be too far for remote
power. Try connecting the local 15 VDC power supply to
the transmitter.
2.
Check the RJ-45 connector for a loose connection.
8.
The transmission distance may be too short. Ensure that
the UTP cable is at least 50' (15.2 m) long.
9.
If the Manual/Auto switch is in the manual position,
ensure that the receiver’s level controls are not set too
high. Too much level and peaking can cause display
problems.
Extron TP Transmitters • Installation and Operation
2-30
Extron TP Transmitters • Installation and Operation
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
TP Transmitters
Appendix
A
Specifications, Accessories, and
Part Numbers
Specifications
Included Parts
Accessories
Cables/Adapters
Extron TP Transmitters • Installation and Operation
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Accessories, and Part Numbers
Video
Audio
Number/signal type ................... 1, 2, or 4 sets of proprietary analog signals
Number/signal type ................... 1 or 2 sets of analog proprietary signals
Connectors .................................... 1, 2, or 4 shielded RJ-45 female
Connectors .................................... 1 or 2 RJ-45 female
Frequency response ..................... 20 Hz to 20 kHz, 0.05 dB
THD + Noise ................................ 0.03% @ 1 kHz, 0.3% @ 20 kHz at nominal
level
Video input
Number/signal type
TP T 15HD A, TP T 468 ... 1 analog RGBHV, RGBS, RGsB,
component video, or S-video; or
S/N ................................................ >63 dB at the rated maximum output
Crosstalk ....................................... <-80 dB @ 1 kHz, fully loaded
Stereo channel separation .......... >80 dB @ 1 kHz
1 S-video and 1 NTSC/PAL/SECAM
composite video from a single source; or
3 NTSC/PAL composite video from a
single source
CMRR ............................................ >33 dB @ 20 Hz to 20 kHz
Audio input
Number/signal type
TP T 15HD AV ................. 1 analog RGBHV, RGBS, RGsB,
component video, or S-video; or
1 S-video and 1 NTSC/PAL/SECAM
composite video from a single source; or
3 NTSC/PAL/SECAM composite video
from a single source
and 1 NTSC/PAL/SECAM composite
video
TP T BNC DA4 .................. 1 analog RGBHV, RGBS, RGsB,
component video, or S-video; or
TP T 15HD A, TP T 468 ... 1 stereo, unbalanced
TP T 15HD AV ................. 2 stereo, unbalanced
Connectors
TP T 15HD A, TP T 468 ... (1) 3.5 mm mini jack
TP T 15HD AV ................. (1) 3.5 mm mini jack, 2 female RCA
Impedance .................................... 5k ohms, unbalanced, DC coupled
Nominal level ............................... -10 dBV (316 mV)
Maximum level ............................ +5.5 dBu, (unbalanced) at 1% THD+N
CMRR ............................................ >75 dB @ 20 Hz to 20 kHz
1 S-video and 1 NTSC/PAL/SECAM
composite video from a single source; or
3 NTSC/PAL/SECAM composite video
from a single source
Audio output — Refer to the TP Receivers Family User’s
Manual.
Connectors
TP T 15HD A, TP T 468 ... (1) 15-pin HD female (Mac and Sun/SGI
to VGA adapters are available)
TP T 15HD AV ................. (1) 15-pin HD female (Mac and Sun/SGI
to VGA adapters are available)
1 RCA female
TP T BNC DA4 .................. 5 BNC female
General
Power
TP T 15 HD A, TP T 468,
TP T 15 HD AV ................ 15 VDC, 0.8 A, external or provided by the
TP R receiver for up to 300' (91.4 m)
Nominal level ............................... 1.0 Vp-p for Y of component video and
S-video, and for composite video
TP T BNC DA4 ................. 15 VDC, 0.8 A, external
The TP R 15HD A receiver does not provide power to
any twisted pair transmitter.
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
0.3 Vp-p for C of S-video
Minimum/maximum level(s).... 0.3 V to 1.45 V p-p, no offset at unity gain
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 130 kHz
Vertical frequency ....................... 30 Hz to 150 Hz
Temperature/humidity .............. Storage -40 to +158 °F (-40 to +70 °C) /
10% to 90%, non-condensing
Operating +32 to +122 °F (0 to +50 °C) /
10% to 90%, non-condensing
Cooling .......................................... Convection, no vents
Video output — Refer to the TP Receivers Family User’s
Manual.
A-2
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Accessories, and Part Numbers, cont’d
Rack mount
Regulatory compliances
Safety ................................. CE, C-tick, CUL, UL
EMI/EMC ......................... CE, C-tick, FCC Class A, ICES, VCCI
MTBF ............................................. 30,000 hours
TP T 15 HD A,
TP T 15HD AV,
TP T BNC DA4 ................. Yes, with optional TP rack shelf mounting
kit, part #70-123-01 (RSM 100) and the 1U,
9.5" deep rack shelf, part #60-190-01
Warranty ....................................... 3 years parts and labor
(RSU 129) or 60-604-02 (RSB 129)
Specifications are subject to change without notice.
All nominal levels are at 10%.
Also furniture mountable with optional
under-desk mounting kit, part #70-077-01
(MBU 125) or through-desk mounting kit,
part #70-077-02 (MBD 129)
TP T 468 ............................. No, but wall or furniture mountable in a
wall box
TP T 468 EC ...................... No, but wall or furniture mountable in a
Euro Channel raceway
Enclosure type.............................. Metal
Enclosure dimensions
TP T 15HD A,
TP T 15HD AV,
TP T BNC DA4 ................. 1.3" H x 6.8" W x 4.5" D
(<1U high, <half rack width)
(3.3 cm H x 17.3 cm W x 11.4 cm D)
(Depth excludes connectors.)
TP T 468
Plate ............................... 4.5" H x 8.3" W (4-gang)
(11.4 cm H x 21.2 cm W)
Transmitter enclosure . 2.6" H x 3.1" W x 1.1" D
(6.6 cm H x 7.9 cm W x 2.8 cm D)
(Depth excludes front and rear panel
connectors and controls.)
TP T 468 EC
Plate ............................... 3.2" H x 7.7" W (8.0 cm H x 19.5 cm W)
Transmitter enclosure . 2.5" H x 3.7" W x 1.75" D
(6.4 cm H x 9.4 cm W x 4.5 cm D
(Depth excludes front and rear panel
connectors and controls.)
Product weight
TPT15HDA,TPT15HDAV 0.8 lbs (0.4 kg)
TP T BNC DA4 .................. 0.9 lbs (0.4 kg)
TP T 468, TP T 468 EC ..... 0.7 lbs (0.3 kg)
Shipping weight........................... 3 lbs (1.4 kg)
Vibration ....................................... ISTA/NSTA 1A in carton
(International Safe Transit Association)
A-4
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Accessories, and Part Numbers, cont’d
Included Parts
Accessories
These items are included in each order for a specific TP
transmitter:
Accessory
Part number
P/S 150 Multiple output 15V power supply
Extron 9.5" Deep 1U Rack Shelf kit (RSU 129)
60-432-01
60-190-01
Included parts
Replacement part number
Extron 9.5" Deep 1U Basic Rack Shelf (RSB 129)
Extron TP Rack Mounting Kit (RSM 100)
Extron Under Desk Mounting Kit (MBU 125)
Extron Through-desk Mounting Kit (MBD 129)
4-gang “J” box 2.5" (6.4 cm) deep
60-604-02
70-123-01
70-077-01
70-077-02
980097
TP T 15HD A
60-345-02
TP Transmitters Family User’s Guide
Single output external power supply, 15 V, 0.8 A
Captive screw connector, 3 pole, 3.5 mm
TP T 15HD AV
70-057-01
10-265-03
60-346-03
TP Transmitters Family User’s Guide
Single output external power supply, 15 V, 0.8 A
Captive screw connector, 3 pole, 3.5 mm
TP T 468
Cables and Adapters
70-057-01
10-265-03
Skew-Free™ A/V UTP cables are not recommended for
Ethernet/LAN applications.
Skew-Free™ A/V cable
Part number
TP T 468 (gray)
60-434-01
60-434-02
60-434-03
60-434-10
68-546-03
70-057-01
UTP 23SF-4/3 — 3' (90 cm)
26-569-01
26-569-02
26-569-03
26-569-04
26-569-05
26-569-06
26-569-07
26-569-08
26-570-04
26-570-05
26-570-06
26-570-07
26-570-08
26-570-09
26-570-10
26-570-11
26-570-12
TP T 468 (black)
UTP 23SF-4/6 — 6' (1.8 cm)
TP T 468 (white)
UTP 23SF-4/12 — 12' (3.6 m)
TP T 468 (EC)
UTP 23SF-4/25 — 25' (7.6 m)
TP Transmitters Family User’s Guide
Single output external power supply, 15 V, 0.8 A
UTP 23SF-4/35 — 35' (10.6 m)
UTP 23SF-4/50 — 50' (15.2 m)
4-gang mud ring (gray, black, white)
TP T BNC DA4
70-086-03, -13, -23
60-349-02
UTP 23SF-4/75 — 75' (22.8 m)
UTP 23SF-4/100 — 100' (30.4 m)
UTP23SF-4P/25 — 25' (7.6 m) plenum
UTP23SF-4P/35 — 35' (10.6 m) plenum
UTP23SF-4P/50 — 50' (15.2 m) plenum
UTP23SF-4P/75 — 75' (22.8 m) plenum
UTP23SF-4P/100 — 100' (30.4 m) plenum
UTP23SF-4P/150 — 150'(45.7 m) plenum
UTP23SF-4P/200 — 200' (61 m) plenum
UTP23SF-4P/250 — 250' (76.2 m) plenum
UTP23SF-4P/300 — 300' (91.4 m) plenum
TP Transmitters Family User’s Guide
Single output external power supply, 15 V, 0.8 A
Captive screw connector, 3 pole, 3.5 mm
70-057-01
10-265-03
The TP T 15HD AV is a redesigned transmitter. The
audio portion of the composite video TP link can be
configured to work with the similarly redesigned
TP R BNC AV receiver or with older, unmodified
receivers. See “Audio jumpers” in chapter 2,
“Installation and Operation.” Redesigned transmitters
and receivers have an identifying label.
A-6
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Accessories, and Part Numbers, cont’d
Bulk cable
Part number
UTP23SF-4/1000 — 1000' (300 m) non-plenum
UTP23SF-4/1000 — 1000' (300 m) plenum
RJ-45 connector
22-141-03
22-142-03
Part number
CAT 6 jack (black)
100-476-01
100-477-01
100-478-01
10-479-01
CAT 6 jack (red)
CAT 6 jack (blue)
CAT 6 jack (orange)
CAT 6 jack (gray)
10-480-01
CAT 6 jack (white)
CAT 6 jack (ivory)
10-481-01
10-482-02
Assorted cables and adapters
Part number
VGA-A M-M MD/3 — 3' (90 cm)
MHRA 15HD cable with audio
26-490-01
VGA-A M-M MD/6 — 6' (1.8 cm)
MHRA 15HD cable with audio
26-490-02
26-531-01
26-260-03
26-316-02
26-353-01
26-353-03
SYM BNCF/.05 — 6" (15 cm) cable
MHR5 BNC/25 — 25' (7.6 m) cable
MHR-2 SVM-M/6 — 6' (1.8 m) cable
SVHSM - BNCF — 8" (20 cm) adapter
SVHSM - BNCM— 3' (90 cm) adapter
Optional Adapter Plates
A variety of optional adapter plates for pass-through
connections can be ordered for the TP T 468, which can have up
to four adapter plates installed. The following configurations of
adapters can be installed in a TP T 468:
•
•
Four single-space (single-height) adapter plates
Two single-space (single-height) adapter plates and one
double-space adapter plate
•
Two double-space (single-height) adapter plates
The tables on the following pages list the available adapter
plates.
A-8
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
Extron TPTransmitters • Specifications, Accessories, and Part Numbers
A-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Accessories, and Part Numbers, cont’d
A-10 Extron TPTransmitters • Specifications, Accessories, and Part Numbers
Extron TPTransmitters • Specifications, Accessories, and Part Numbers A-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Accessories, and Part Numbers, cont’d
Blank Plate (no connector)
Single Space
Blank Plate (no connector)
Double Space
2 - BNC
5 - BNC (Double)
3 - BNC
2 - RCA to Solder Cups
3 - RCA to Solder Cups
2 - S-video
2 - RJ-11
1 - D-9 Pass Through Connector
1 - HD-15 Pass Through Connector
2 - F Connectors
2 - 1/4" Stereo Phono
2 - 3.5mm Stereo Mini
1 - 3-pin XLR Connector
Figure A-1 — Architectural adapter plates
TP T 468 Template
The following template is actual size. It also includes the
recommended 0.1" (0.25 cm) clearance on all sides of the
electrical wall box to allow room for raised area surrounding the
knockout.
The dashed line on the template indicates the cut-out area for
installing a wall box. If you plan to install the TP T 468 without
a wall box, use the smaller cut-out area indicated by the dotted
lines.
Use the following template as a guide for cutting a hole in a
wall or furniture for the 4-gang size electrical box in order to
install the transmitter.
A-12 Extron TPTransmitters • Specifications, Accessories, and Part Numbers
A-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Accessories, and Part Numbers, cont’d
A-14 Extron TPTransmitters • Specifications, Accessories, and Part Numbers
Download from Www.Somanuals.com. All Manuals Search And Download.
|