Extron electronic Network Cables BNC 5 RC User Manual

BNC 5 RC Termination Instructions  
Shielding  
BNC plug body  
Color-coded  
heat shrink tube  
Center  
pin  
Ferrule  
.496"  
(11.9 mm)  
.375"  
2
Support sleeve Conductor Outer insulation  
(9.5 mm)  
1. Slide the color coded heat shrink tubing or BNC  
strain relief over the cable, then slide the ferrule over  
the cable. See the top diagram.  
.094"  
(2.4 mm)  
Conductor  
Outer Insulation  
Shielding  
.250"  
(6.4 mm)  
2. Carefully strip the end of the coaxial cable to expose  
NOT TO SCALE  
the shielding and inner conductor.  
3. Insert the center conductor into the center  
Center pin  
3
pin.  
4. Insert the conductor and pin into  
the crimp tool (part #100-133-01)  
with the included die. With the  
flange on the center pin flush with  
the edge of the die, crimp using  
the die’s .068” crimp height.  
Center Contact - flange flush  
with edge of die  
4
Crimp Center Contact  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
USA  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort  
The Netherlands  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Building  
Singapore 368363  
Extron Electronics, Japan  
Daisan DMJ Building 6F  
3-9-1 Kudan Minami  
Chiyoda-ku, Tokyo 102-0074 Japan  
+81.3.3511.7655  
714.491.1500  
+31.33.453.4040  
+65.6383.4400  
68-482-01  
Rev. D  
Fax 714.491.1517  
Fax +31.33.453.4050  
Fax +65.6383.4664  
Fax +81.3.3511.7656  
5. Insert the center pin into the BNC  
body until the pin meets resistance.  
Continue firmly pushing the pin into  
the BNC body until the pin snaps  
into the detent position.  
BNC plug body  
5
5
6. Slide the exposed shielding over the support  
sleeve of the BNC.  
7. Slide the ferrule over the  
7
shielding and against the BNC  
body. Using the die’s .213” crimp  
height, crimp the ferrule.  
Crimp ferrule  
8. Slide and set the heat shrink  
tubing or BNC strain relief over  
the ferrule.  
Heat shrink tubing  
8
Related tools and parts list:  
or  
Recommended  
glue  
Crimp tool ............................................ 100-133-01  
BNC 5 RC cable (500’ spool) ................ 22-127-02  
Male BNC RC connectors (qty. 50) ...... 10-452-01  
Install strain relief  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edimax Technology Switch EU HB4S User Manual
Eiki Projector LC NB1U User Manual
Extron electronic Switch 68 1316 02 User Manual
GE Clothes Dryer DCCD330GDKC User Manual
GE Dishwasher 165D4700P390 User Manual
Geemarc Telephone 4 CID User Manual
GE Microwave Oven JEB1860SM User Manual
Generac Power Systems Portable Generator 00862 1 User Manual
GE Oven JTP13 User Manual
GE Water Heater AP13204 4 User Manual