Extron electronic Car Satellite TV System MTP R 15HD RSA D User Manual

MTP R 15HD RSA D • Setup Guide  
This guide provides basic instructions for an experienced installer to set up and operate  
the Extron MTP R 15HD RSA D receiver.  
Pre-installation  
T568A  
T568B  
Pins:  
12345678  
Pin Wire color  
Wire color  
The MTP R 15HD RSA D receiver can be installed in a one-gang electrical wall box with  
a Decora wall plate cover (supplied).  
1
White-green  
Green  
White-orange  
Orange  
2
3
4
5
Choose a location that allows cable runs without interference. Allow enough depth for  
both the wall box and the cables. The box should be at least 2.5 inches (6.4 cm) deep  
to accommodate the connectors and cables. Install the cables into the wall, furniture,  
or conduits before installing the receiver.  
White-orange White-green  
Blue  
Blue  
White-blue  
Orange  
White-blue  
Green  
6
7
8
Insert Twisted  
Pair Wires  
White-brown White-brown  
Brown Brown  
The top image at right details the recommended termination of TP cables with RJ-45  
connectors in accordance with the TIA/EIA T568A or TIA/EIA T568B wiring standards.  
You can use either standard with CAT 5/5e/6 cable, but ensure that you use the same  
standard on both ends of the cable.  
NOTE: If you are using Enhanced Skew-Free™ AV  
cable, use the TIA/EIA T568A standard only.  
Power Supply Wiring  
Wire the power connector (see the image on the right). Verify the polarity before  
POWER  
12V  
connection by plugging in the power supply with no load and checking the output  
with a voltmeter.  
xA MAX  
Rear  
Panel  
Smooth  
Ridges  
A
A
Grounding guidelines  
Extron MTP 15HD RSA D products can be adversely affected by electrostatic discharge)  
(ESD) if they are not grounded correctly.  
3/16"  
(5 mm)  
Max.  
Tie  
Wrap  
To prevent malfunctions or product damage, an experienced installer can correctly  
ground an Extron MTP 15HD RSA D product grounding the power input port. Insert one  
end of the grounding wire to the negative or ground pin on the power input connector  
(see the image on the right). Tie the other end of the wire to an earth ground.  
Ridges  
SECTION A–A  
Power Supply  
Output Cord  
Earth  
Ground  
If you have any questions about how to ground a product in a specific application,  
contact an Extron technical support specialist.  
For more information and warnings, see “Power supply wiring” in the MTP R 15HD RSA D  
User’s Manual.  
Installation  
MTP 15HD RSA D Rx Rear Panel  
Connect/Configure the Rear Panel  
a DC power connector — If applicable, plug the external 12 VDC power supply into  
2
this 2-pole captive screw connector (see power wiring details above).  
b Input connector — Connect the TP cable from the transmitter to this pigtail RJ-45  
H SYNC +  
V SYNC +  
C SYNC  
SOG  
VIDEO  
Bi-RS232  
INPUT  
female connector (see the table above on the top right to wire the RJ-45 connectors).  
3
1
H
V
SYNC  
SYNC  
SYNC  
+
+
C
SOG  
VIDEO  
c DIP switches — Set the DIP switches to the desired preference (see Set the DIP  
Switches on the next page for more details).  
Bi-RS232  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edelbrock Automobile Parts 16211 MBN 640 User Manual
Eizo Computer Monitor FlexScan F520 User Manual
Fender Speaker 11040 User Manual
Fisher Price Doll G9157 User Manual
Franke Consumer Products Ventilation Hood FDB 9078 SIL K User Manual
Frigidaire Freezer GLFC1326FW User Manual
FujiFilm Digital Camera 16437542 User Manual
Furuno Telephone FS 5070 User Manual
Garmin Marine GPS System 190 01120 00 User Manual
GE Clothes Dryer DCD330EB User Manual