EZ-PLATECAM-002
High Contrast
License Plate Capture Camera
INSTALLATION & OPERATION MANUAL
Before attempting to connect or operate, please read and follow these instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Cautions
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful inter ference.
2. This device must accept any inter ference received, including
inter ference that may cause undesired operation.
Note -
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful inter ference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful inter ference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful inter ference in which case the user will be
required to correct the inter ference at his own expense.
WARNING -
This is a class A product. In a domestic environment this product may
cause radio inter ference in which case the user may be required to take
adequate measures.
Caution -
Any changes or modifications in construction of this device which are
not expressly approved by the party responsible for compliance could
void the user ’s authority to operate the equipment.
1. If DC power is used a regulated DC12V 1A power supply is recommended for use
with this camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
If an unregulated power supply is used, product warranty will be void.
2. It is recommended that the camera is used with a monitor or other equipment that
has a CCTV quality 75 video impedance level.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to the manufacturer.
4. Never face the camera towards the sun, any bright, or reflective light that may
cause smear on the picture or cause possible damage to the CCD.
5. Do not remove the serial number sticker.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Cautions
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes. Contact the
company where you purchased this product or your local government office for details
on how to properly dispose or recycle the product to be environmentally safe.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
Household users should contact the retailer for proper disposal procedures.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Features
• 1/3" Sony Super-HAD CCD
Ⅱ
• OSD Menu system customizes performance to match application
• High Resolution 600TV Lines
• Special filter and IR LEDs provide maximum readability
despite headlight glare
• Plate capture up to 35mph (56Km/H)
• 9.0 ~ 22.0mm Varifocal lens captures license plate
from 8ft ~ 33ft (2.5M ~ 10M)
• IP66 rated weather resistant
• Cable concealed through bracket
• DC12V / AC24V Dual power with auto-polarity
3. Items Provided In The Box
CAMERA
SUNSHIELD
VIDEO OUTPUT
TEST CABLE
L-WRENCH /
SCREW & Plastic anchor - 3ea /
SUNSHIELD FIXING BOLT
OPERATION MANUAL
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Component and Control Names and Functions
4.
⑥
①
②
①
③
⑧
⑦
④
⑤
Sunshield Lock Bolt
Sunshield
Mounting Bracket
IR LED : 20ea
Camera Body
Body Lock Ring
①
②
③
④
⑤
⑥
⑦
External Zoom and Focus adjustments
⑦
TEST
VIDEO
OUTPUT
Cover To Access Menu Controls & Test Video Output
⑧
Pressing the “SETUP”button prompts the main setup menu.
“PUSH”button : To access the main setup menu
“U”Direction : Menu item UP selection
“D”Direction : Menu item DOWN selection
“L”Direction : To change data or decrease value
“R”Direction : To change data or increase value
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Installation
• ADJUSTING CAMERA POSITION
360
˚
90
˚
360
˚
Loosen socket head allen screws to change angle
and/or rotate body about base.
Loosen this lock ring
to rotate camera body.
After adjusting zoom and focus,
to prevent water infiltration, firmly
tighten the zoom and focus levers.
WARNING !
360
˚
To prevent injury, this apparatus must be securely
attached to the mounting surface with sufficient
strength to hold the weight of the camera including
wind and snow loading in accordance with the
installation instructions.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Installation
• CONNECTIONS
DUAL(DC12V/AC24V)
Power Supply
24VAC 300 mA min ; 500 mA Recommended
12VDC 600 mA min ; 1A Recommended
DC12V/AC24V
BNC FEMALE
VIDEO IN
DVR OR
OTHER CCTV
EQUIPMENT
WHITE: TRIGGER SIGNAL
BLACK: TRIGGER GROUND
OSD CONTROL
VIDEO TEST POINT
CONNECTION
HANDHELD
VIDEO IN
TEST CABLE
Note: Face of connector with color mark should
face “up”when inserting test cable.
When you install the camera, please seal the end of cable to
protect the camera connections from humidity problems.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. OSD Functions
OSD Menu Structure
• OSD Access
To access OSD menu unscrew cover plate on rear
of camera, press “in”on joystick to access OSD Menu
SETUP
.
• MODE
▶
MODE
LICENSE-PLATE
1/250
- INSTALLATION
SHUTTER
FREEZE-TIME
NEG. IMAGE
EXIT
5SEC
OFF
Installation Mode provides a bright video
screen to adjust angle and focus.
- LICENSE-PLATE
License-plate Mode provides high
contrast and clear license plate image
for license plate capture.
SETUP
MODE
LICENSE-PLATE
1/250
• SHUT TER
SHUTTER
FREEZE-TIME
NEG. IMAGE
EXIT
▶
1/250, 1/500, 1/1,000 ~ 1/10,000.
(After 1/1000sec, 1/500sec unit adjustment )
5SEC
OFF
- Adjusted when LICENSE-PLATE MODE is performed.
(Initial value: 1/250)
- Indicated “---”when INSTALLATION MODE is set.
* Depending on the vehicle speed, you may adjust camera SHUTTER SPEED
• FREEZE
SETUP
The video screen will automatically go
in to FREEZE mode when Camera is
triggered by sensors connected to the
trigger input.
MODE
LICENSE-PLATE
1/250
SHUTTER
FREEZE-TIME
NEG. IMAGE
EXIT
5SEC
OFF
▶
User can set the freeze time to 3, 5, or 10 sec.
• NEGATIVE
User can select positive or negative image.
SETUP
MODE
SHUTTER
FREEZE-TIME
LICENSE-PLATE
1/250
5SEC
▶NEG. IMAGE
OFF
EXIT
Negative ON
Negative OFF
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation Guidelines
Camera Height
Consider camera height in distance calculation.
Sharper angles will alter the appearance of the plate.
•
•
Shallow angles are recommended)
(
20˚
Camera Height (ft) Horizontal Distance (ft)
Capture Distance (ft)
2.74
3.76
4.79
5.81
6.84
7.87
8.89
9.92
11.29
7.52
10.34
13.16
15.97
18.79
21.61
24.43
27.25
31
8
11
14
17
20
23
26
29
33
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation Guidelines
Camera Angles
Vertical and horizontal angle must not exceed 20 degrees to
achieve proper view of the license plate.
•
H-angle < 20˚
V-angle < 20˚
V-angle less than 20˚correct
H-angle less than 20˚correct
Both horizontal and veritical agles affect maximum capture distance.
Increasing eigther or both angels will decrease maximum capture distance.
•
•
Capture Zone
Wider angles provide shorter capture distance.
Tele angles provide longer capture distance.
•
•
WIDE SETTING -39˚@ f=9mm
TELE SETTING -12.6˚@ f=22mm
Ⓐ
Ⓑ
Ⓒ
5M
10M
2.5~5M
WIDE
SETTING
5~10M
TELE
SETTING
< NOTE: Red and white color license plate number can not be recognized >
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation Guidelines
Lane Width
Narrow lanes = less variation in plate location.
Wider lanes = more variation in plate location.
Lens should cover entire width of the lane.
Ensure horizontal field of view is wide enough.
•
•
•
•
Speed
Camera can capture moving vehicles up to 35mph.
•
(SHUTTER Speed less than 1/500)
Keep camera as low as possible.
Minimize horizontal angle.
•
•
•
Zoom in the lens as close as possible.
Up to 35 mph
12
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation Guidelines
Trigger
Camera provides a trigger input is for freezing the video screen.
Connect to external sensor e.g. Parking Gate Sensor.
Trigger input should be pulled-up 3.3V DC in normal condition.
Input line will be triggered when pull-up 3.3V DC drop to GND.
•
•
•
•
DVR
Camera is fully compatible with industry standard DVRs.
•
•
•
Check compression settings.
For best results use non-conditional refresh compression.
(i.e. MJPEG or JPEG)
(Other Video codecs can sometimes cause an indistinct picture)
Use 30fps (each channel) for best results.
DVR Set
•
•
Interlace DVR
720 x 240
720 x 480
Deinterlace DVR
13
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Specifications
Signal Format
Image Device
Total Pixels
Effective Pixels
Inter. H/V
NTSC
1/3" Sony Super HAD CCD
PAL
Ⅱ
811(H) x 508(V)
768(H) x 494(V)
795(H) x 596(V)
752(H) x 582(V)
15.734KHz(H), 59.94Hz(V)
15.625KHz(H), 50Hz(V)
H.Resolution
Minimum illumination
S/N Ratio
600TV Lines
0 Lux (IR LED ON)
More than 50dB (AGC Off)
Internal
Sync System
Video Output
Lens
1.0 Vp-p Composite(75Ω)
Varifocal (9~22mm) Auto Iris
850nm, 20ea
IR LED
IP Rating
IP66
Speed Rage
License
Up to 35mph (56km/h)
8ft ~ 33ft (2.5m ~ 10m)
Maximum 20 degree offset
14˚F~122˚F(-10˚C ~ +50˚C)
-4˚F~140˚F(-20˚C ~ +60˚C)
Plate
Capture Distance
Capture
Capture Angle
Operating Temperature
Storage Temperature
DC12V 10% Max 570mA
AC24V 10% Max 6.7W
Power consumption
Weight
Approx. 1000g (2.20 lb)
Dimension
82mm x 79.3mm (3.23inch x 3.12inch)
Specifications and designs are subject to change without notice for improving the functionality of this product.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Dimensions
unit: mm(inch)
82 (3.23)
145 (4.92)
120 (4.72)
224 (8.82)
M12 XP 1.0
3.5( 0.14)
Ф
Ф
Bottom of Bracket
65 ( 2.56)
Ф
Ф
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
Mount Guide
3-ø5.3
Download from Www.Somanuals.com. All Manuals Search And Download.
EverFocus Electronics Corp.
Corporate Headquarters:
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
China Office:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing, China 100085
TEL: +86-10-62973336~39
FAX: +86-10-62971423
TEL: +886-2-26982334
FAX: +886-2-26982380
U.S.A - California Office:
1801 Highland Avenue Units A & B
Duarte, CA 91010
U.S.A - New York Office:
415 Oser Avenue Unit S
Happauge, NY 11788
TEL: +1-631-436-5070
FAX: +1-631-436-5027
TEL: +1-626-844-8888
FAX: +1-626-844-8838
Europe - Germany Office:
Albert-Einstein-Strasse 1,
D-46446 Emmerich, Germany
TEL: +49-2822-93940
FAX: +49-2822-939495
Japan Office:
5F Kinshicho city Building,
2-13-4 Koto-Bashi,
Sumida-Ku, Tokyo, 130-0022 Japan
TEL: +81-3-5625-8188
FAX: +81-3-5625-8189
India Office:
UK Office:
Suite 803, Housefin Bhavan, C-21,
Bandra Kurla Complex, Bandra (East),
Mumbai 400051. India.
TEL: +91-222-444-8791
FAX: +91-222-444-8790
Unit 12 Spitfire Business Park
Hawker Road
Croydon, CR0 4WD
London: 0845 430 9999
Telford: 0845 430 8888
Fax: 020 8649 9907
Ihr EverFocus Produkt wurde
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
entwickelt und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Please, dispose of this equipment at
your local community waste
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|