3 Speed Electronic Sweeper
with No Touch Dust Cup
OWNER’S MANUAL
Model: V1917H
8.4 Volt DC
U.S :
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Canada : EURO-PRO Operating LLC
4400 Bois Franc
Plattsburgh, NY 12901
St-Laurent, QC H4S 1A7
1 (800) 798-7398
Copyright © Euro-Pro Operating LLC 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
V1917H
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic safety precautions should always be observed,
including the following
ONE (1) YEAR LIMITED WARRANTY
READ ALL INSTRUCTIONS BEFORE USING YOUR CORDLESS SWEEPER.
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, return the complete appliance and accessories, freight prepaid to:
WARNING: To reduce the risk of fire, electrical shock, or injury:
1. Do not charge this unit outdoors.
2. Do not use outdoors or on wet surfaces.
3. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
In US:
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901
In Canada: EURO-PRO Operating LLC, 4400 Bois Franc, St Laurent, Qc, H9S 1A7
4. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date must be included. *
Non-durable parts including, without limitation, dust cups and brushes which normally require
replacement are specifically excluded from warranty.
5. Do not use with damaged cord or plug. Do not use cordless sweeper if it has
been dropped, damaged, left outdoors, or dropped in water. Return it to EURO-
PRO Operating LLC for examination, repair or adjustment.
6. Do not abuse the charger cord. Never carry the charger or base by the cord or
yank to disconnect from an outlet; instead grasp the charger and pull to disconnect.
7. Keep charger cord away from heated surfaces.
8. This product includes rechargeable nickel cadmium batteries. Batteries must be
recycled or disposed of properly. Do not incinerate batteries or expose to high
temperatures, as they may explode.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement
of the unit at our option. This warranty does not cover normal wear of parts and does not apply to
any unit that has been tampered with or used for commercial purposes. This limited warranty does
not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging
or mishandling in transit. This warranty does not cover damage or defects caused by or resulting
from damages from shipping or repairs, service or alterations to the product or any of its parts,
which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
9. Do not handle plug or appliance with wet hands.
10. Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair and anything that may reduce air flow.
11. Keep hair, loose clothing, fingers, and all parts of body away from openings and
moving parts.
12. Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes.
13. Do not attempt to change accessories while unit is running.
14. Use extra care when cleaning on stairs.
15. Do not use to pick up flammable or combustible liquids such as gasoline or use in
areas where they may be present.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with item. We recommend you insure the package (as damage in
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore
the specifications contained herein are subject to change without notice.
16. Read and follow all label, operational and marking instructions.
17. Do not use charger with an extension cord. Plug charger directly into an electrical
outlet. Use charger only in a standard (120V., 60Hz) electrical outlet.
18. Do not use the cordless sweeper without dust container in place.
19. Store the cordless sweeper indoors. Store after use to prevent accidents.
20. Leaks from battery cells can occur under extreme conditions. If the liquid, which
is 20-35% solution of potassium hydroxide, gets on the skin – wash immediately
with soap and water or neutralize with a mild acid such as lemon juice or vinegar.
If the liquid gets into the eyes, flush them immediately with clean water for a
minimum of 10 minutes and seek medical attention.
ꢀyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
For Canadian Consumers Only
Please fill out and mail the product registration card within ten (10) days of purchase. The
registration will enable us to contact you in the unlikely event of a product safety notification. By
returning this card you acknowledge to have read and understood the instructions for use, and
warnings set forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St Laurent, Qc, H9S 1A7
V1917H
_______________________________________________________________________
21. Use only on dry, indoor surfaces.
Appliance model
22. Do not use for any purpose other than described in this user’s guide.
23. Do not attempt to use the charger with any other product or attempt to charge this
product with another charger. Use only charger model TechWorld AD-1215-U8
supplied with this appliance.
_______________________________________________________________________________
Date purchased
Name of store
_______________________________________________________________________________
Owner’s name
_____________________________________________________________________________
24. The appliance must be disconnected from the supply when removing the battery.
Address
City
State
Zip Code
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
Printed in China
12
1
Rev. 05/06A
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND COMPONENTS
OPERATING INSTRUCTIONS
TROUBLESHOOTING GUIDE
1. Upper Handle
2. Telescopic Tube
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
3. No Touch Empty Button
4. Lower Handle Extension Tube
5. Lower Handle
6. Charging Light Indicator
7. On/Off Switch
8. Charging Adapter: Only Use
TechWorld AD-1215-U8
9. Charging Jack
10. Transparent Brush Cover
11. Rotating Brush
1. Charge unit.
2. Check fuse or breaker.
Replace fuse/reset breaker.
3. Call Customer Service at
1 (800) 798-7398.
4. Ensure that the wire terminal
connectors are securely
attached.
5. Clear any obstruction from the
rotating brush. Turn unit off for
10 seconds, and then restart.
1. Batteries discharged.
2. No power in electrical
outlet supplying charging
adapter.
3. Unit needs servicing.
4. Battery misplaced.
5. Brush roll jammed.
SWEEPER WILL
NOT OPERATE
12. Edging Tool
13. Gear Box
SWEEPER WILL
NOT PICK-UP
1. Dust container is full.
2. Unit needs recharging.
1. Empty dust container.
2. Charge unit.
14. Sweeper Power Head
15. Dust Cup Container
16. Speed Indicator Lights
17. Speed Control
DUST ESCAPING
FROM SWEEPER
1. Dust container is full.
1. Empty dust container.
18. Dust Container Release Lever
1. Check for excessive material
on brush or in bottom of
sweeper. Remove obstruction
from brushes and/or sweeper.
2. Empty and clean dust
container.
ROTATING BRUSH
WILL NOT PICK UP
1. Unit clogged.
2. Dust container is full.
1. Electrical outlet not
working.
2. Charging Adapter not
working.
1. Check to ensure outlet is
working properly. (Easily
checked by plugging in
SWEEPER WILL
NOT CHARGE
another appliance.
3. Batteries no longer
functioning.
4. Unit left in “On” position.
2. Replace charging adapter.
3. See battery disposal.
4. Press switch to “Off”.
* Illustrations may differ from actual product.
NOTE: The cordless sweeper is shipped with the batteries uncharged.
Charging of the unit for 20 hours prior to first use is required.
Use replacement battery # XBP1917H only.
2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
8. Slip the belt over the brush bar cap.
9. Insert the brush bar into the slot. (Fig. 14)
Assembling Your Cordless Sweeper
Your cordless sweeper will require very little assembly. You should remove it from
the carton and familiarize yourself with all the components listed per the exploded
view drawing. (Pg. 2) This will help you in the assembly and operation of your
cordless sweeper.
10. Insert the gear box tabs into the tab slots and push down until it clicks into place.
11. To replace the squeegee, follow instructions above for removing the gear box and
slide the squeegee out from left to right. (Fig. 16)
Note: The charging adapter will be shipped inside the packaging.
Note: The lower handle extension tube has a different plastic insert. This tube
should be the first on the assembly.
1. Assemble the extension tubes by pushing the plastic insert into the mating
extension tube. (Fig. 1a) Push until only small portion of insert is visible or you
cannot press any farther into the tubing. Push the extension tube assembly into
the upper handle. (Fig. 1) Insert the extension tube assembly into the lower
handle so that the tab on the plastic insert snaps into the open slot on the lower
handle. (Fig. 1b)
Fig. 15
Changing the Belt
If you find that the belt has broken and it needs replacing:
1. Remove the brush cover. (Fig. 11)
2. Push in on the locking tab of the gear box and lift gear box to remove. (Fig. 12 & 13)
3. Push in on the locking tab of the belt access panel and lift off to remove. (Fig. 17)
Belt Access Panel
Fig. 16
Insert into
Lower
Handle
4. Using a pair of tweezers, remove any leftover bits of the belt that might still be
there.
5. Pull the brush bar out of the bushing. (Fig. 14)
6. Using a new belt, insert it into the opening until it is in all the way.
7. Using a pair of tweezers, insert them into the belt access panel and lift the new belt
over the back gear.
Fig. 1a
Fig. 1b
8. Slide the belt over the brush bar cap and then insert the brush bar into the slot.
(Fig. 14)
9. Insert the gear box tabs into the tab slots and push down until it clicks into place.
10. Press the belt access panel down until it snaps in place.
11. Replace the brush cover (Fig. 11)
Fig. 1
Care And Maintenance
To improve the performance and life of your unit, we recommend you do the
following:
2. Place the handle into the upward storage position.
1. Once a month clean the unit with a dry cloth, including the chamber which the dust
container fits into. Remove any hair, fiber or other materials that may have built up
in the chamber, and on the rotating brush.
2. Don’t use abrasive materials to clean the sweeper. Do not immerse the unit in
water.
3. Do not pick up liquids or use on wet floors.
4. Do not use on concrete, tar or similar rough surfaces.
5. Don’t pick up pieces of string or fabrics with the sweeper.
6. Do not clean tasseled or frayed carpets with the sweeper.
10
3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Changing The Rotating Brush, Gear Box & Squeegee
1. Remove the extension tube handle from the sweeper power head.
2. Turn the sweeper power head upside down being careful not to accidentally turn
the unit “On”.
Charging Instructions
1. Connect the charger plug to the charging jack or hole on the side of the sweeper.
Plug the charging adapter into the wall outlet. (120V., 60Hz.) Use only TechWorld
Charger AD-1215-U8. (Fig. 2)
3. Remove the brush cover.
4. Push in on the locking tab of the gear box and lift the gear box to remove.
Charging
Light
Indicator
(Fig. 12 & Fig 13)
Lift
Locking
tab
Gear box
Fig. 2
2. This cordless sweeper is powered by Ni-Cd batteries. Before first use, they must
be charged for a minimum 20 hours.
Gear box
tabs
3. When recharging the unit, the "On/Off" switch must be in the "OFF" position.
4. The charging light indicator on the top of the sweeper will illuminate to indicate
that the sweeper is properly charging.
5. To recharge, repeat step #1 above. Charging times will vary depending upon the
amount of usage between charging cycles.
Fig. 13
Fig. 12
5. Lift the brush bar end cap up from the slot. (Fig. 14)
Note: If, when you place the sweeper to recharge and the charging indicator light does
NOT illuminate, then press the On/Off button once to turn the sweeper off. The
charging indicator light should now light up.
Note: Peak performance may only be realized after the unit has been charged and
discharged two (2) or three (3) times.
Important: To maintain peak performance of your cordless sweeper, it is
recommended that the unit be fully discharged, then completely re-charged at least
once a month.
Fig. 14
6. Pull the brush bar out from the bushing and slip off the belt to remove the brush
bar. (Fig. 15)
7. Insert the new brush bar by first inserting the brush bar into the bushing on the end
opposite the driver belt (Fig. 15)
Caution:
•
•
•
•
•
Use only the adaptor supplied with the sweeper.
Do not clean the sweeper while unit is charging.
Do not attempt to remove the battery pack from the unit to charge it.
Never attempt to throw the battery pack or unit into a fire or incinerate it.
Do not attempt to remove or damage the battery casing.
Fig. 15
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Cleaning The Dust Container
To Maximize The Life Of Your Ni-cd Batteries
To achieve the best performance, empty the dust container after each use.
1. Press the dust cup release lever with your foot. (Fig. 9)
Note: Be careful not to accidentally turn the unit “On”
1. Charge for a minimum of 20 hours before initial use. Failure to do so will reduce
the product’s battery life significantly.
2. Do not store the unit with the charging adaptor attached and plugged in.
3. Only recharge when the batteries are fully discharged (or as close to fully
discharged as possible).
4. Do not store in areas of high temperature or humidity.
5. After three (3) months of storage, the product should be fully discharged and then
recharged to maximize battery power.
6. Use only the charger supplied with the product. If other chargers are used, the
batteries can fail causing damage to the battery, product or personal property.
7. Ni-Cd batteries have a long useful life but at some time they will need to be
replaced. To purchase replacement batteries and parts call EURO-PRO customer
service at 1 (800) 798-7398.
Note: If the product has never been used or has been stored for an extended period of
time without use – it will take several complete charge and discharge cycles to realize
the full operational time of your product.
Fig. 9
2. Lift out the dust container, which is connected to the handle. Hold over a trash bin
and push down on the no touch empty button located on the handle. (Fig. 10)
Battery Removal & Disposal
One Touch
Note: If uncertain as to how to remove your battery pack, we suggest you take your
sweeper to a reputable small appliance service technician to have this service
performed.
Empty Button
Follow the steps in “Removal of Battery Pack” when battery removal is required.
Fig. 10
This sweeper is equipped with Ni-Cd batteries and you need to dispose of them properly.
When the batteries are no longer good for use, they must be removed from the sweeper
for disposal. Do not remove the batteries for any reason other than disposal of them.
Call your nearest recycling center for information on the recycling and disposal of
Ni-Cd batteries.
3. To close the dust container press firmly on the bottom panel until it snaps back into
place. To replace the dust cup, position onto the sweeper power head and press
down firmly until it snaps back into place.
4. Periodically remove the transparent brush cover on the front of the cordless
sweeper and remove any build up of lint, hair or fiber on the rotating brush.
To remove the cover - grip the cover from the bottom, pull out and upward until the
cover unlocks from the side slots and tabs located on the top of the sweeper.
Carefully cut away threads or hair with scissors. (Fig. 11)
Warning: You must never use ordinary batteries for replacement as these may leak and
cause damage. Use only battery pack XBP1917H provided for replacement.
Removal of Battery Pack
1. Press the dust cup release lever with your foot and remove it from the sweeper
power head.
2. Turn unit over so that the base is facing upwards. Be careful not to turn the unit ON.
3. Push in locking tab and lift off battery compartment cover. (Fig. 3 & 4)
Battery Pack
Compartment Cover
Battery Case Tab
Fig. 11
Caution: Do not accidentally turn unit on while cleaning.
Caution: Any electronic or electrical appliance should not be stored in or
exposed to areas of high heat or humidity. Do not store your cordless sweeper
close to stoves, radiators, furnaces or in a bathroom or bathing area.
Fig. 4
Fig. 3
8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
How To Operate Your Cordless Sweeper
1. Before using, please ensure that the cordless sweeper has been initially
4. Carefully lift out the battery pack and disconnect the wire terminals by pulling apart
the wire terminal connectors. Remove the battery pack from the unit. (Fig. 5)
charged for 20 hours.
Your cordless sweeper will only operate properly when the batteries are fully
charged. Your sweeper will operate for varying lengths of time on a full charge.
This will depend upon the type of surface being cleaned. (Longer operating time on
bare floors vs. carpets.)
Wire Terminal Connector
Fig. 5
2. Push the On/Off switch to operate the unit. To turn off, press switch again. (Fig. 6)
5. Connect the wire terminal connector from the unit to the wire terminal connector of
the new battery pack, and replace the battery pack into the unit. Replace the cover
and press until it snaps in place.
"On/Off“ switch
6. Follow instructions for initial battery charging. Please call customer service at
1 (800) 798-7398 if there are any problems removing batteries.
Fig. 6
Do NOT attempt to replace the batteries used in this product with any other type of
battery.
3. To release the handle to a comfortable position, gently apply pressure to the top of
the sweeper head with your foot while pulling back on the handle. (Fig. 7)
Important: This appliance contains Ni-Cd batteries. The batteries must be
recycled or disposed of in accordance with local regulations. Please consult your
Yellow Pages or local recycling center for more information.
Fig. 7
4. To change the speed of the sweeper, press on the speed control button. As you
press on it, the speed indicator light will change. If one light lights up, you have the
low speed for hard floors; two lights, medium speed for carpeting; three lights, high
speed for turbo deep cleaning. (Fig. 8)
Hard floors
Carpeting
Turbo Deep
Cleaning
Fig. 8
Anti-Jam Brush Roll Feature
This feature protects your unit’s motor from damage due to overheating, that may be
caused by the rotating brush getting jammed or tangled in something. If the rotating
brush becomes overloaded it will stop turning and both speed indicator lights will
remain flash at the same time. To reset the unit:
1. Press On/Off switch.
2. Remove the transparent brush cover from the sweeper power head to remove any
build up of lint, hair or fiber on the rotating brushes.
3. Wait for 10 seconds to allow the unit to cool down.
4. Press On/Off switch again, the unit should restart.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|