Model V1055H
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase. This warranty
applies only to normal domestic household use.
Should your appliance fail to operate properly while in use under normal household conditions
within the one (1) year warranty period, return the complete appliance and accessories, freight
prepaid to EURO-PRO Operating LLC at the address given below.
Bagless Upright Vacuum
EURO-PRO Operating LLC,94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901
If the appliance is found by EURO-PRO Operating LLC to be defective in material or
workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of
purchase date and $18.95 to cover the cost of return shipping and handling must be included. *
Non-durable parts including, without limitation, drive belts, rotating brushes and electrical parts
which normally require replacement are specifically excluded from warranty.
OWNER’S MANUAL
Model V1055H
120V., 60Hz., 12 Amps
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement
of the unit at our option. This warranty does not cover normal wear of parts and does not apply to
any unit that has been tampered with or used for commercial purposes. This limited warranty does
not cover damage caused by misuse, abuse, negligent handling or damage due to faulty
packaging or mishandling in transit. This warranty does not cover damage or defects caused by or
resulting from damages from shipping or repairs, service or alterations to the product or any of its
parts, which have been performed by a repair person not authorized by EURO-PRO Operating
LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with item. We recommend you insure the package (as damage in
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase. The registration will enable
us to contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to
have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
RETURN TO: EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
Model V1055H
______________________________________________________________________
Appliance model
______________________________________________________________________________
Date purchased
Name of store
______________________________________________________________________________
Owner’s name
______________________________________________________________________________
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Address
City
State
Zip Code
Tel.: 1 (800) 798-7398
Printed in China
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM SOLVING
PRECAUTIONARY MEASURES
This appliance was inspected thoroughly and was in good operating condition when it
was shipped from the factory. If a minor problem occurs, it usually can be solved quite
easily when the cause is found. Therefore, this checklist is provided for your
convenience.
Important: If the suction opening in the unit, the hose or the extension tube become
blocked, switch off the vacuum cleaner and remove the blocking
substance before you start the unit again.
5. When pulling out the power plug
from the wall outlet, pull the plug
not the power cord.
1. Do not operate the vacuum cleaner
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
too close to heaters, or radiators.
1. Not properly plugged into wall
outlet.
2. No electricity in wall outlet.
3. On/Off switch not turned on.
4. Motor thermostat tripped.
5. Blown fuse/tripped breaker.
1. Plug in firmly.
2. Check fuse or breaker.
3. Push on/off switch to on
4. Reset motor thermostat.
5. Reset circuit breaker or
replace fuse.
Cleaner Won’t
Run
1. Clean dust cup (container).
2. Adjust setting.
1. Full or clogged dust cup.
2. Wrong pile height setting.
3. Clogged nozzle.
4. Clogged dust inlet port.
5. Clogged hose.
6. Broken belt.
7. Hose not inserted fully.
8. Dirty filters.
3. Remove obstruction.
4. Remove power head cover
and remove obstruction.
5. Remove obstruction.
6. Replace belt.
7. Push hose in securely.
8. Clean / change filters.
9. Clean or replace HEPA Type
filter and filter ring.
6. Do not pick up anything that is
burning or smoking such as
2. Before inserting the power plug
into the wall outlet, make sure that
your hands are dry.
Cleaner Won't
Pick Up
cigarettes, matches or hot ashes.
7. Do not run appliance over power
9. HEPA Type filter and filter ring
needs cleaning or replacing.
cord.
8. Do not use without dust cup
Cleaner Picks
Up Moveable
Rugs Or Pushes
Too Hard
(container) or filters in place.
1. Wrong pile height setting.
1. Adjust setting.
9. Before you start vacuuming,
make sure to remove large or
sharp objects that might
3. Do not vacuum any liquids.
1. Replace belt.
2. Check belt changing and
agitator cleaning.
damage the vacuum.
Agitator Does
Not Turn
1. Broken belt.
2. Belt installed incorrectly.
Note: This vacuum cleaner is equipped
with a plug and power cord that retract
automatically. If the cord or plug get
damaged, it must be replaced by a
qualified technician.
Air Flow
1. Attachment use restricts air
flow.
2. New carpet debris clogging air
path.
Restricted With
Attachment Use
Sound Changes
1. Check attachment.
2. Remove obstruction.
Warning: Hold the plug when
rewinding the cord. Do not allow the
cord to whip when rewinding.
4. Keep hair, loose clothing, fingers,
feet and all parts of body away from
openings, rotating agitator and other
moving parts.
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING TO KNOW YOUR BAGLESS BAGLESS
UPRIGHT
OPERATING INSTRUCTIONS
5. Carefully clear away any excess
Storage
dust or debris from agitator.
6. Remove agitator from housing
starting on the left side followed by
the right side.
7. If the belt has broken, remove any
loose pieces before replacing with
a new belt.
8. Remove the worn or broken belt
from the motor drive shaft.
9. Loop the new belt first over the
drive shaft then over agitator into
the groove on the right side of the
agitator. (Fig. 11)
10. Insert the right side of the agitator
by placing the end cap down into
the slot on the housing and then
align the left side. Press down
firmly to make sure that each end
of the agitator is correctly fitted
into the slots.
To store the vacuum cleaner, put it in
the upright position. Turn the power
“Off”. Remove the power cord from the
electrical outlet. Press the cord rewind
button. If the cord does not fully retract,
pull it out again and then press on cord
rewind button.
Warning: Hold the plug when
rewinding the cord. Do not allow the
cord to whip when rewinding.
Note: Before using the appliance,
unwind a sufficient length of cable and
Insert the plug into the wall socket. A
yellow mark on the power cord shows the
ideal cable length. Don’t pull the power
cord beyond the red mark.
Motor Thermostat
Important: This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
Motor
Belt
• Push the On/Off button once.
• Disconnect the plug from the power
source.
Agitator
• Check the source of overheating
problem. (i.e. clogged hose or filter)
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for 45
minutes, plug in the cleaner and
push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
Fig. 11
NOTE: There will be some tension on
the belt as the agitator is being put into
place.
11. Make sure that the belt is centered
on the pulley and the agitator
turns.
12. Replace the front end of the top
cover ensuring the wheel hubs fit
properly in place. (Fig 12)
13. Lift handle to secure top cover
over carpet height selector.
9. Handle Release Pedal
10. Cord Rewind Button
11. Hose Intake
1. Handle
2. Telescopic Handle
3. Telescopic Tube Height
Adjustment Button
12. Flexible Hose
13. Power Cord Clip
14. Telescopic Tube Release Button
15. Crevice Tool
16. Dusting Brush
17. Power Cord
4. On/Off Button
14. Drop handle so that the vacuum is
laying flat again. Holding the top
and bottom of unit gently turn unit
over and replace the screws. Do
not turn the screws too tightly to
avoid stripping the screw holes.
5. Dust Cup Release Button
6. Dust Cup (Container)
7. Carpet Height Adjustment Knob
8. Motorized Power Head
18. Hose Connector
Technical Specifications
Voltage:
Power:
120V., 60Hz.
12 Amps
Fig. 12
Note: Illustrations may differ from actual unit.
Wheel Hub
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Assembling Your Vacuum Cleaner
WARNING: Always remove the power
plug from the wall outlet before
PLEASE NOTE: The white pleated
Using the Attachments
Cleaning the Filter Ring
1. Around the HEPA-Type
filter there is a filter
ring. This is washable
in lukewarm water.
filter material in the HEPA-Type Filter
will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA-
Type Filter
1. Place vacuum in its upright position.
Make sure that the vacuum cleaner
is NOT plugged into the electrical
outlet when adding or removing
accessories.
assembling or removing accessories.
Assembling the Vacuum Cleaner
1. Carefully unpack all the components,
set the packaging aside.
2. Lift the vacuum body to the upright
position.
3. Insert the handle into the handle inlet
of the vacuum.
4. Press down on the telescopic tube
height adjustment button while
pushing the telescopic tube down.
(Fig. 1)
(Fig. 10) To remove
the filter ring, slide it
off the HEPA-Type filter.
2. We recommend
washing the filter ring
when you are
Fig. A
is properly
2. Turn the carpet height
selector to the
highest position.
3. Remove the
"TapCleaned”
after each use
and suction
Wash
once a
month or
when
suction
appears
reduced
does not return
to 100%, then
we suggest that
the HEPA-Type
filter be
“TapCleaned”
vigorously until
no more dust
telescopic tube
from the unit following
the instructions on
washing your
HEPA-Type filter.
Always allow the
Fig. 10
page 4.
filter ring to air dry for
24 hours before replacing onto
Warning: Allow 24
hours for drying before
replacing in unit.
4. Remove the hose
connector from the
the HEPA-Type filter. Never run the
vacuum without all the filters in place.
Note: This is a washable filter, but we
recommend replacing it every three (3)
months.
side of the unit.
5. Insert the flexible
hose into the top of
the handle. (Fig. 3)
can be removed, then rinsed under
the faucet and allowed to air dry for 24
hours before refitting into the vacuum.
(Fig. A) This should be done once a
month or when suction appears to
be reduced .
Telescopic Tube
Height Adjustment
Button
6. Insert the desired
Cleaning & Changing the Belt
attachment firmly
onto the end of the
telescopic tube.
Fig. 3
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA-Type filter,changing the filters
or performing maintenance/trouble
shooting checks.
Occasionally the power head drive belt
will require changing, the frequency will
depend upon the amount of use your
vacuum sees.
1. Turn the vacuum "Off" and unplug
from power supply.
2. Release the handle by pressing the
handle release pedal and pull back
on the handle unit it releases from its
upright position, and turn the unit over
on the floor.
3. With a #2 Phillips screw driver,
remove the four (4) screws on the
bottom base plate. There are two in
the front of the unit and 2 screws
recessed in the back.
4. With the unit still lying down, hold the
top and bottom plates together while
turning the unit over. Remove the one
(1) screw that holds the carpet height
adjustment button Lift the cover of
the power head starting from the
back.
Warning: When the vacuum is turned
on, the beater brush will continue to
rotate. AVOID tipping the vacuum or
setting it on furniture, fringed area rugs or
carpeted stairs while you are using the
hose with attachments. AVOID leaving
the vacuum in one place for an extended
period of time, particularly on thick carpet.
Warning: Always empty
the dust cup container and
clean the HEPA-Type filter, filter ring
and filter frame before each use and
during prolonged usage.
Fig. 1
Never over fill the dust cup container -
remove dirt and clean the HEPA-Type
filter, filter ring and filter frame when dirt
in dust cup is at or below the “FULL"
level or during prolonged usage because
you could risk damaging the motor.
If you wash the Hepa-Type filter and
filter ring, make sure that they have
completely air dried for 24 hours
before inserting back into the
vacuum.
Please Note: The HEPA-Type Filter is
washable. It should, however, be replaced
every three (3) to six (6) months to ensure
peak performance of your vacuum.
The filter ring is also rinseable but should
be air dried for 24 hours before replacing
into the vacuum. It should however be
replaced every three (3) months to ensure
peak performance of your vacuum.
Important: Make sure that ALL filters are
completely dry before re-installing back in
the vacuum.
5. To remove the telescopic tube,
extend it to its maximum height by
depressing the telescopic tube height
adjustment button and then press the
telescopic tube release button and
pull the tube out. (Fig. 2)
Crevice Tool
For radiators, crevices,
corners, baseboards and
between cushions.
Dusting Brush
The dusting brush is used
for the furniture, Venetian
blinds, lamp shades,
shelves, etc.
Telescopic Tube
Release Button
Caution: Do NOT pull the vacuum
cleaner around the room by the hose as it
could tip over and cause damage. When
using the attachments, Do NOT over
extend the hose length when reaching.
Trying to reach beyond the hose reach
could cause the vacuum to tip over. The
dust cup cover handle can be used to lift
the vacuum when changing locations.
Fig. 2
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
2. Remove the filter assembly from the
Place unit in “UPRIGHT" position when
How to Start
dust cup container.
using attachment or hose to prevent
possible floor damage. Always set the
carpet height selector to “highest”
setting when using the accessories and
hose.
Attention: Special care is required
when vacuuming certain types of carpet
or floor covering. Always check the
carpet or floor covering manufacturer's
recommended cleaning instructions
before vacuuming.
The vacuum can be used on multiple
types of carpeting or bare floors. When
using the crevice tool or dusting brush,
place the handle of the vacuum in the
upright position.
3. To separate the filter assembly, hold
the bottom of the filter frame and
pull the HEPA-Type filter out.
(Fig. 9)
Trap Door
Release Button
Filter Assembly
1. Plug the power cord into the electrical
outlet.
HEPA-Type
Filter
Store or use
2. Push the On/Off
attachments
button to the "On"
position to turn
the vacuum on.
3. To release the
handle, step
Use
Filter
Ring
Fig. 7
Clean under
furniture
•
The dust cup container can be
washed in lukewarm water.
Do not use strong detergents.
Ensure that the dust cup container
is fully dry before putting back on
the vacuum cleaner.
Removing & Emptying Dust Cup
(Container)
Filter
Frame
on the handle
release pedal
and pull back handle.
•
•
Handle release
Fig. 4
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup (container), dust cup HEPA-Type
filter, changing the pre-motor filter or
performing maintenance/trouble shooting
checks.
Important: Do NOT use the vacuum
without ALL the filters in place.
The “Dust Cup (Container)” must always
be emptied when the dirt level reaches
the “FULL" line on the dust cup
(container). To remove the dust cup
(container) from the vacuum:
Fig. 9
4. When using the crevice tool or dusting
brush, the vacuum must be in the
upright position. (Fig. 4)
•
Do not wash in dishwasher.
4. Remove the filter ring that is
around the
Cleaning the HEPA Filter and the
Filter Frame
Warning: After each Use - Always
remove the Filter Assembly, then
vigorously tap clean the HEPA-Type
Filter until no more dust can be
removed.
Carpet Height Selector
HEPA-Type
filter. Then
vigorously
“TapClean” the
This upright vacuum can be used on
multiple types of carpeting and bare
floors. To select a pile height setting:
1. Turn vacuum cleaner "Off".
2. Select a pile height setting by
rotating the carpet height selector
to the desired setting. (Fig. 5)
HEPA-Type Filter on a hard
surface until no more dust is
observed falling out.
5. To clean the filter
frame, we
IMPORTANT, Please Note: The
Rinseable “TapClean” HEPA-Type Dust
Cup Filter will quickly accumulate many
fine dust particles inside the white filter
folds that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. Clean the
HEPA-Type Filter after each use as
described in this section.
Carpet height
selector
1. Press down on the dust cup
release button that is located on the
dust cup cover handle of the dust
cup. (Fig. 6)
recommend that
you rinse it under
lukewarm running
water to remove
the dirt that
accumulates
on it, but always
Dust Cup
Release Button
Fig. 5
Suggested Pile Height Setting:
allow 24 hours to air dry before
inserting back into the vacuum.
6. To re-assemble the filter
assembly, insert the filter ring over
the HEPA-Type filter and then
insert the HEPA-Type filter
assembly into the filter frame.
Replace the filter assembly into
the dust cup container. Replace
the dust cup container cover.
1. To remove the filter assembly from
the dust cup, hold the dust cup
cover from the handle in one hand
and with the other hand, turn the
dust cup container counter
You may need to raise the height of the
vacuum to make some jobs easier,
such as scatter rugs and longer pile
carpets. Suggested settings are:
clockwise. (Fig. 8)
Open
Mark
HIGH: shag carpet, long pile, plush
scatter rugs, tools
medium to long pile
Fig. 6
MED:
2. To empty the dust cup container,
hold the dust cup from the handle
over a garbage container and press
on the trap door release button that is
on the back side of the dust cup
container to release the dust cup
bottom. (Fig. 7)
LOW: very low pile, bare floors
Arrow
for
alignment
Fig. 8
6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|