3-Speed Cordless Sweeper
OWNER’S MANUAL
Model: UV627
7.2 Volt DC
EURO-PRO Operating LLC
U.S.: 94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Canada: 4400, Bois-Franc
St-Laurent, QC H4S 1A7
Tel. : 866-98shark
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
To improve the performance and life of your unit, we recommend you do the
following:
1. Once a month clean the unit with a dry cloth, including the chamber which the dust
container fits into. Remove any hair, fiber or other materials that may have built up in
the chamber, on the rotating brush or edging tool.
2. Don’t use abrasive materials to clean the sweeper. Do not immerse the unit in water.
3. Do not pick up liquids or use on wet floors.
4. Do not use on concrete, tar or similar rough surfaces .
5. Don’t pick up pieces of string or fabrics with the sweeper.
6. Do not clean tasseled or frayed carpets with the sweeper.
Model UV627
7.2 Volt DC
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
1. Batteries discharged.
2. No power in electrical
outlet supplying charging
adapter.
1. Charge unit.
SWEEPER WILL NOT
OPERATE
2. Check fuse or breaker.
Replace fuse/reset breaker.
3. Call Customer Service.
3. Unit needs servicing.
SWEEPER WILL NOT
PICK-UP
1. Dust container is full.
2. Unit needs recharging.
1. Empty dust container.
2. Charge unit.
DUST ESCAPING
FROM SWEEPER
1. Dust container is full.
1. Empty dust container.
1. Check for excessive material
on brush or in bottom of
sweeper. Remove obstruction
from brushes and/or sweeper.
2. Empty and clean dust
container.
ROTATING BRUSH
WILL NOT PICK UP
1. Unit clogged.
2. Dust container is full.
11. Charging Adapter
1. Sweeper Power Head
2. On / Off Switch
3. Speed Control
4. Charging Light Indicator
5. Speed Indicator Lights
6. Rotating Brush
7. Brush Cover
8. Edging Tool
9. Gear Box
10. Dust Container
1. Electrical outlet not
working
2. Charging Adapter not
working
3. Batteries no longer
functioning
1. Check to ensure outlet is
working properly. (Easily
checked by plugging in
another appliance.
2. Replace charging adapter
3. See battery disposal pg. 8.
(TechWorld AD-1215-UL8
rated output DC 12V, 150mA)
12. Charging stand
13. Lower Handle
14. Upper Handle
15. Extension tubes
16. Charging Jack (Main Unit)
17. Charging Jack (Charging
Stand)
SWEEPER WILL NOT
CHARGE
STORING THE CORDLESS SWEEPER
Your cordless sweeper may be stored by using the slot on the back of the upper
handle and hanging it from a screw secured to a wall or other vertical surface. Use
a #6 flat or pan head screw with the appropriate hardware for the surface that the
sweeper will be mounted on, (i.e. gyproc). Allow the screw head to extend a
approximately 3/16" from the mounting surface. Always empty your sweeper before
hanging up for storage.
NOTE: Cordless Sweeper Model UV627 is shipped with the
batteries uncharged. Charging of the unit for 20 hours
prior to first use is required.
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING YOUR CORDLESS SWEEPER
Battery Removal & Disposal
Before you start:
NOTE: If uncertain as to how to remove your battery pack, we suggest
you take your sweeper to a reputable small appliance service
technician to have this service performed.
Your Cordless Sweeper will require very little assembly. You should remove it from the
carton and familiarize yourself with all the components listed as per the exploded view
drawing (pg.2) This will help you in the assembly and operation of your cordless
sweeper.
Follow these steps when battery removal is required.
Note: The charging adapter and the lower handle are shipped inside the dust cup.
This sweeper is equipped with Ni-Cd batteries and you need to dispose of them
properly. When the batteries are no longer good for use, they must be removed from
the sweeper for disposal. Do not remove the batteries for any reason other than
disposal of them. The batteries must be recycled or disposed of in accordance
with local regulations. Please consult your Yellow Pages or local recycling
center for more information.
Lower Handle
WARNING: You must never use ordinary batteries for replacement as these
Fig. 1
Fig. 2
may leak and cause damage. Use only battery pack XBP615
for replacement.
1. In the event that the edging tool is not attached to the sweeper, insert the edging
tool into the "square" hole under the bottom of the sweeper power head. Gently
but firmly push until the edging tool locks into place. (Fig. 1)
Removal of Battery Pack
2. Insert the lower handle - small end - into the sweeper power head. Push until
1. Remove the extension tube and dust container.
2. Turn unit over so that the base is facing upwards. Be careful NOT to turn the unit
ON. (Fig. 19)
firmly in place. (Fig. 2)
3. Assemble the extension tubes by pushing the plastic insert into the mating extension
tube. (Fig. 3a) Push until only small portion of insert is visible or you cannot press
any farther into the tubing. Push the extension tube assembly into the upper handle.
(Fig. 3)
3. Push in locking tab and lift off battery assembly. (Fig. 20)
4. Place battery assembly aside.
5. Insert the new battery assembly into unit. Ensure that locking tab snaps in place.
NOTE: One extension tube has a different plastic insert. This tube should be
on the bottom of the handle.
Insert the extension tube assembly into the lower handle so that the tab on the
plastic insert snaps into the open slot on the lower handle. (Fig. 3b)
4. Place the handle into the upward storage position.
5. Plug the charging adapter into the sweeper power head charging jack or plug the
charging adaptor into the charging jack of the charging stand. If using the charging
stand, place the sweeper onto the charging stand to charge. Plug the charging
adapter cord into a standard electrical outlet (120V, 60Hz.) The red charging
indicator should illuminate. If it does not, depress the On/Off switch one time.
CAUTION: This appliance contains Ni-Cd batteries. The batteries must
be recycled or disposed of in accordance with local
regulations. Please consult your Yellow Pages or local
recycling center for more information.
Insert into Lower
Handle
Fig. 3
Fig. 19
Fig. 20
Fig. 3a
Fig. 3b
CAUTION: ALWAYS USE ADAPTOR SUPPLIED (ONLY)
WITH SWEEPER
8
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Rotating Brush, Gear Box & Squeegee
HOW TO OPERATE YOUR CORDLESS SWEEPER
1. Before using, please ensure that the cordless sweeper has been initially
charged for 20 hours
WARNING: Use caution when changing the rotating brush and gear
box so that the unit does not turn ON when pressing down
on the sweeper power head.
Your cordless sweeper will only operate properly when the batteries are fully
charged. Your sweeper will operate for varying lengths of time on a full charge.
This will depend upon the type of surface being cleaned. (Longer operating time
on bare floors vs carpets.)
1. Remove the extension tube handle from the sweeper power head.
2. Turn sweeper power head upside down being careful Not to accidentally turn the
unit ON.
2. Push the On/Off switch to operate the unit. To turn off, press switch again.(Fig.4)
3. Remove the brush cover. (Fig. 13) (Refer to page 5 for detailed instructions.)
4. Push in on the locking tab of the gear box and lift gear box to remove. (Fig. 14 &
Fig. 15)
"On/Off" switch
5. Lift the brush bar end cap up from the slot. (Fig. 16)
6. Pull the brush bar out from the bushing and slip off the belt to remove the brush bar.
(Fig. 17)
7. Insert the new brush bar by first inserting the brush bar into the bushing on the end
Fig. 4
opposite the driver belt. (Fig. 17)
8. Slip the belt over the brush bar cap.
9. Insert the brush bar into the slot. (Fig. 16)
10.Insert the gear box tabs into the tab slots and push down until it clicks into place.
11.To replace the squeegee, follow instructions above for removing the gear box and
slide the squeegee out from left to right. (Fig. 18)
CAUTION: Any electronic or electrical appliance should not be
stored in or exposed to areas of high heat or humidity. Do
not store your cordless sweeper close to stoves,
radiators, furnaces or in a bathroom or bathing area.
Lift
Locking
tab
Gear box
3. To release the handle to a comfortable position, apply pressure to the top of the
sweeper head with your foot while pulling back on the handle.(Fig. 5)
Fig. 14
Gear box
tabs
Fig. 13
Fig. 15
Fig. 5
Fig. 16
Fig. 17
4. To change the speed of the sweeper, press on
Hard floors
the speed control button. As you press on it, the
speed indicator light will change. If one light lights
up, you have the low speed for hard floors; two
lights, medium speed for carpeting; three lights,
high speed for turbo deep cleaning. (Fig. 6)
5. Flashing LED lights indicate that the brush bar
system id blocked or jammed. If this occurs, first
turn the unit off, then remove the obstruction
before turning the unit on again.
Carpeting
Turbo Deep
Cleaning
Fig. 18
Fig. 6
4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Your sweeper is highly advanced and has electronic controls that optimize the
cleaning ability and durability of the sweeper. Please review the following instructions
carefully to ensure that all features are utilized for best performance.
CLEANING THE DUST CONTAINER
To achieve the best performance, empty the dust container after each use.
3. Replace dust container on cordless
sweeper.
1. Pull the dust
container straight
out from the side.
(Fig. 7)
1. The electronic controls of your sweeper will prevent the batteries from being deeply
discharged and will indicate this by the speed indicator lights flashing. The sweeper
will then stop operating. This is normal. To start charging the unit, turn the sweeper
off, plug in the adapter or the charging stand and attach the sweeper to charge.
2. When the sweeper on/off switch is depressed the sweeper will slowly come up to
speed. This is done to optimize the life of all components of the sweeper and is
normal.
3. When first started, the sweeper will start in the highest speed “III” to prevent
overloading the unit when starting on heavy carpets. Other speeds can then be
selected by depressing the speed selector switch.
4. For best cleaning performance, use speed “I” (low) on floors, speed “II” (medium) on
carpets, and use speed “III” (high) for turbo deep cleaning. These are guide lines and
you will find the optimum speed settings for your surfaces and debris to be picked up
through use and experience.
5. The sweeper will automatically try to maintain speeds on all surfaces. The unit may
appear to be pulsing during use to maintain it’s speed, this is normal. If this occurs,
please select the next highest speed to gain optimum performance.
6. To protect your sweeper and it’s components, the sweeper is provided with an
electronic overload circuit. If something were to jam or overload the brush bar
system, the units speed indicators will flash and the unit will stop operating, this is
normal. If this occurs, first turn the unit off, then remove the obstruction before turning
the unit on again.
4. Periodically remove the brush cover on
the front of the cordless sweeper and
remove any build up of lint, hair or fiber
on the rotating brush. To remove the
cover - grip the cover from the bottom,
pull out and
upward until the
cover unlocks
from the side
slots and tabs
Fig. 7
2. Empty dust
container contents.
(Fig. 8) If desired-
you may rinse with
water to clean the
dust container –
but dry thoroughly
located on the
top of the
Fig. 8
sweeper. (Fig. 9)
Fig. 9
before replacing on the sweeper.
CAUTION: Do not accidentally turn unit on while cleaning. Do not clean
while unit is charging.
CHARGING THE CORDLESS SWEEPER
1a. Connect the charger plug to the charging jack or hole on the back of the sweeper.
Plug the the charging adapter into the wall outlet. (120V., 60Hz.) Use only
TechWorld Charger AD-1215-UL8. (Fig. 10)
NOTE: If, when you place the sweeper to recharge and the charging indicator
light does NOT illuminate, then press the On/Off button once to turn
the sweeper off. The charging indicator light should now light up.
OR
1b. Connect the charger plug on the charging jack of charging stand (Fig. 11). Plug the
charging adapter into the wall outlet (120V., 60Hz). Use only Techworld Charger
AD-1215-UL8, and place the unit in the charging stand. (Fig. 12)
2. This cordless sweeper is powered by Ni-Cd batteries. Before first use, they must be
charged for a minimum of 20 hours.
NOTE: Peak performance may only be realized after the unit has been charged
and discharged two (2) or three (3) times.
3. When recharging the unit, the "On/Off" switch must be in the "OFF" position.
4. The charging light indicator on the top of the sweeper will illuminate to indicate that
the sweeper is properly charging.
5. When the battery is running low, the speed indicator lights will start to flash. To
recharge, repeat step #1 above. Charging times will vary depending upon the
amount of usage between charging cycles.
IMPORTANT: To maintain peak performance of your cordless sweeper, it is
recommended that the unit be fully discharged, then completely re-
charged at least once a month.
CAUTION
•
•
•
•
•
Use only with the battery pack supplied with the unit. (Item # XBP615)
Do not attempt to remove the battery pack from the unit to charge it.
Never attempt to throw the battery pack or unit into a fire or incinerate it.
Do not attempt to remove or damage the battery casing.
Battery must be recycled or disposed of in accordance with local regulations at the
end of it's service life. Please consult your Yellow Pages or local recycling center
for more information.
Fig. 10
Fig. 11
Fig. 12
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|