Model GI490H
LIMITED WARRANTY
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO OPERATING LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within
the warranty period, return the complete appliance and accessories, freight prepaid to
Intelligent Electronic 1700 Watt Iron
EURO-PRO Operating LLC, 21 Lawrence Paquette Ind. Dr., Champlain, N.Y. 12919
If the appliance is found by EURO-PRO Operating LLC to be defective in material or
workmanship, EURO-PRO will repair or replace it free of charge. Proof of purchase date and $
9.95 to cover the cost of return shipping and handling must be included.*
OWNER’S MANUAL
Model GI490H
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement
of the unit at our option. This warranty does not cover normal wear of parts and does not apply to
any unit that has been tampered with or used for commercial purposes. This limited warranty does
not cover damage caused by misuse, abuse, negligent handling or damage due to faulty
packaging or mishandling in transit. This warranty does not cover damage or defects caused by
or resulting from damages from shipping or repairs, service or alterations to the product or any of
its parts, which have been performed by a repair person not authorized by EURO-PRO Operating
LLC.
120V., 60 Hz., 1700 Watts
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential
damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with item. We recommend you insure the package (as damage in
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
PRODUCT REGISTRATION CARD
Please complete and return within ten (10) days of purchase. The registration will enable us to
contact you in the event a product defect is discovered. By returning this card you acknowledge
to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions.
RETURN TO: EURO-PRO Operating LLC, 21 LAWRENCE PAQUETTE IND. DR., CHAMPLAIN, N.Y. 12919
PURCHASER: ……………………………………………………………………………………………
ADDRESS: ……………………………………………………………………………………………….
For information or assistance:
EURO-PRO Operating LLC
21 Lawrence Paquette Industrial Drive
Champlain, NY 12919
GI490H
DATE OF PURCHASE: …………………….. MODEL: ………………. SERIAL NO: .…………….
NAME AND ADDRESS OF STORE: …………………………………………………………………..
Tel. 1 (800) 798-7398
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING TO KNOW YOUR INTELLIGENT
ELECTRONIC IRON
IRONING CHART
NOTE: Always refer to the garment
To select iron temperature, align
temperature selected on dial with
the indicator on the water tank.
The odor is safe and should not reoccur
after initial heating.
Before using your Intelligent Electronic
care tag for ironing instructions. Before
starting to iron delicate fabrics, it is best
to first test the temperature of the iron
on a hem or an inside seam.
Iron, remove any labels, stickers or tags
that may be attached to the body or
soleplate of the iron.
When turned on for the first time, your
new iron may emit an odor for up to 10
minutes. This is due to the initial
heating of the materials used in making
the iron.
Also, before ironing with steam for the
first time, allow iron to heat, hold in a
horizontal position and hit the burst of
steam button several times. The iron
may emit some small particles from the
steam holes. This is normal and will
clear after pressing the burst of steam
button several times.
DIRECTIONS
ON LABEL
Display Panel
SYNTHETIC
FIBERS, e.g.
acrylic, nylon
polyester
SILK
COTTON
LINEN
FABRIC
WOOL
13
14
LED
DISPLAY
PANEL
MIN
MAX
• • • • •
•
12
MINIMUM
STEAM
MAXIMUM
STEAM
STEAM
CONTROL
0
11
BURST OF
STEAM
1. Electronic Temperature Control
2. Display Panel
3. Atomizer Spray Button
4. Burst of Steam/X-Tended
Steam Burst Button
8. Water Level Window
9. Stainless Steel Soleplate
10. Handle
11. Auto-Off Light
12. Power Light
SPRAY
5. variable steam control
6. Water Inlet Door
7. Spray Nozzle
13. Fabric & Steam Settings
14. Temperature Indicators
15. Water Flask
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES OF THE INTELLIGENT ELECTRONIC IRON
OPERATING INSTRUCTIONS (CONT.)
LED Display Panel
3
STORAGE
NOTE: The anti drip function reduces
water dripping and water stains. It does
not prevent water dripping and water
stains if you press the steam burst
button too often or if the temperature is
too low. The amount of water droplets
will eventually decrease after the iron is
used for 2 to 3 tankfuls of steaming and
ironing.
1. Always turn the variable steam
control to “0” after you have emptied
the water tank.
2. Allow the iron to cool down.
3. Always store the iron in the upright
position to protect the soleplate.
4. From time to time, clean the exterior
of the iron with a damp cloth and
wipe dry.
1 2
5. If you use spray starch, wipe the
soleplate occasionally with a soft
damp cloth to prevent the build-up of
deposits.
4
1. BURST OF STEAM
/X-TENDEDTM STEAM
BURST
6. LED DISPLAY PANEL
Displays the fabric and the
temperature settings.
6. If the iron has not been used for a
few weeks, hold the iron horizontally
and allow to steam for 2 minutes
before ironing.
The X-TendedTM Steam Burst
provides continuous, powerful
steam performance. Can be used
vertically as well as horizontally.
The Burst of Steam provides
extra, sudden blasts of steam
which aid in removing stubborn
wrinkles from fabrics such as
denim, cotton or linen.
7. WATER FILLING INLET
The cover prevents dust and
foreign matter from entering
the water tank. It also stops
any water from spilling during
ironing.
2. ATOMIZER SPRAY
BUTTON
Pressing this Button provides a
defined jet of spray which gently
moistens fabric.
8. BUILT-IN ANTI-CALCIUM
FILTER
3. VARIABLE STEAM
CONTROL
Prevents calcium build-up
and prolongs the life of the
iron.
Minimum to maximum steaming for
different materials. Self cleaning
feature flushes internal sole plate
with water.
9. STAINLESS STEEL
SOLEPLATE
Provides maximum glide-
ability and heat retention.
4. ELECTRONIC
TEMPERATURE CONTROL
Select the fabric setting by
pressing on this button.
10. PIVOT CORD
For left or right handed use.
Pivots up and down;
5. Anti-Drip Function
Cuts off water when the
iron temperature is too
low.
prevents dragging along the
fabric. The flexible cord
protector protects the cord
from fraying.
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS (CONT.)
OPERATING INSTRUCTIONS
ELECTRONIC AUTOMATIC
SHUT-OFF
SELF CLEANING
This appliance is for HOUSEHOLD USE
NOTE: Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
It is important to “Self Clean” the iron at
least every two weeks to remove scale,
calcium, etc. The harder the water, the
more often the iron should be self
cleaned.
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
The ELECTRONIC Iron is equipped with
an electronic auto shut-off. The electronic
auto-off switches the iron off if it has been
left standing unmoved in any position
(sideways, flat or upright) for
approximately 7-9 minutes. A red light on
the LED display panel will flash when the
iron switches itself off. (Fig. 7) To switch
the iron back on, just shake the iron side-
to-side several times.
DRY IRONING
1. Set the variable steam control dial
to any steam position.
WARNING: Never fill the iron with
fabric conditioner, starches or any
other liquid, as these will damage the
steam mechanism. Do not use
contaminated water.
All marked settings on the LED display
panel can be used for dry ironing. Turn
the variable steam control dial all the
way to the right to “0”. This will cut off
the steam flow if water is in the tank.
2. Fill the water tank up to the “MAX”
level.
3. Stand the iron on its heel. Plug the
iron into the electrical outlet.
1. Open the water filling inlet cover.
Holding the iron at a slight angle,
pour water slowly into the water
filling inlet. See figure 1. Fill tank to
desired level or to the “MAX” water
level marking using the water filling
flask. (When the iron is upright, the
see-through water tank allows you to
gauge the amount of water.) DO
NOT overfill the tank. When finished
filling the iron with water, close the
water inlet cover before continuing.
1. Press on the electronic temperature
control button to select the desired
fabric/temperature setting. Turn the
variable steam control dial to “0”.
(See “Ironing Guide” for a guide to
temperature selection.)
4. Press the electronic temperature
control button until you get the
“MAX” temperature setting on the
display panel and wait until the iron
heats up and temperature setting
light stops flashing.
2. Plug the cord into a polarized, 120V
AC electrical outlet. The power “ON”
light will come on, indicating that the
iron is receiving power.
5. Turn the variable steam control dial
to the self-cleaning position and hold
the iron horizontally over the sink.
(Fig. 8).
3. Place iron on its heel (on a stable,
protected surface) while iron is
warming to desired temperature.
6. Boiling water and steam will now be
ejected from the holes in the
soleplate. The impurities and scale
are washed away with it.
Flash
Fig. 7
STEAM IRONING
7. Move the iron back and forth as this
happens.
EMPTYING THE IRON
1. Always empty iron after each use.
CAUTION! DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
8. If there is any water left in the water
tank after the iron stops steaming,
just empty the remaining water in a
sink following the instructions for
emptying the iron.
2. When finished using the iron, turn
the variable steam control dial to
“0” and press the electronic
temperature control button until the
power light is lit.
WARNING! Before filling the iron
with water, be sure the iron is not
plugged into the electrical outlet. The
iron may be filled with water while it
is hot.
Fig. 1
2. Plug the cord into a polarized, 120V
AC electrical outlet.
9. Turn the variable steam control dial to
the “0” position when the water tank
is empty.
3. Unplug the iron from the electrical
outlet.
3. Press on the electronic temperature
control button to select the desired
fabric and temperature setting. Turn
the variable steam control dial to
the desired steam setting. (See
“Ironing Guide” for a guide to
4. Turn the iron upside down over the
sink with the tip pointing downward
and allow the water to flow from the
opening.
CAUTION! TO PREVENT THE RISK
OF BURNS, use caution when filling
iron with water. Burns can occur
from touching hot metal parts, hot
water, or steam.
10.Place the iron back upright on its
heel to cool down before storing.
5. Place iron upright and allow to cool
before storing.
temperature selection.)
CAUTION! Use caution when
emptying the iron. Burns may occur
from touching hot metal surfaces,
hot water or steam.
Fig. 8
4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS (CONT.)
OPERATING INSTRUCTIONS (CONT.)
ATOMIZER SPRAY NOZZLE
4. Place the iron on its heel on a stable,
protected surface and allow the iron
to heat for approximately two (2)
minutes or until the temperature
settings on the right side of the LED
display panel have stopped flashing.
5. Turn the variable steam control dial
to the right to increase the amount of
steam. When using extra steam, the
iron uses more water and it may be
necessary to fill the water tank more
often. (Fig. 2)
The atomizer spray nozzle is useful on
fabrics with stubborn wrinkles. Press the
spray button and a jet of water will spray
onto the fabric being ironed. (Fig. 5) The
water spray can be used with dry or
steam ironing as desired.
Temp.
settings
Fig. 3
NOTE: If the tank runs dry, remove the
plug from wall outlet. Then, fill the iron
with water and re-prime the pump. The
iron may be filled with water while it is
hot.
To use the X-TendedTM Steam Burst
feature:
Fig. 6
IRONING HINTS
Fig. 5
4. Set the variable steam control dial
to the desired steam setting.
5. Turn the steam button to the
maximum steam setting. (Fig. 4)
6. Press the electronic temperature
control button until you get to the
desired fabric setting.
7. To maintain a constant flow of
steam, make sure that the water
tank is at least half full.
WARNING! To prevent fire, do not
leave iron unattended while
connected.
SELECTING IRON TEMPERATURES
Always read garment labels and follow
the manufacturer’s ironing instructions.
Refer to the “Ironing Chart” on page 12
for temperature recommendations:
Fig. 2
•
Sort articles to be ironed according
to the type of fabric. This will reduce
the need to adjust the temperature
for different types of garments.
BURST OF STEAM/X-TENDEDTM
STEAM
•
Use low settings for nylon or other
synthetics.
CAUTION! DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
•
If you are not sure of the fiber
content of a garment, test a small
area such as a seam or inside hem
section before ironing a visible area.
Start with a low temperature setting
and gradually increase to find the
best setting.
•• Use moderate settings for wool,
silks, and blends.
••• Use high settings for cottons and
linens.
The burst-of-steam button is useful
when ironing denim, cotton, and linens.
It provides extra, sudden blasts of
steam which aid in removing stubborn
wrinkles.
1. Stand the iron upright on its heel.
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press the electronic temperature
control until you get the desired
fabric/temperature setting.
4. The light on the right side of the LED
display panel will stop flashing when
the desired temperature has been
reached. (Fig. 6)
•
•
When reducing the temperature to
iron sensitive fabrics, allow
approximately 2 minutes for the iron
to cool to the new temperature
setting.
The burst-of-steam feature can be used
with Dry or Steam ironing as desired.
1. Make sure the water tank is at least
1/2 filled with water.
Fabrics such as velour, wool, linen
and silk are best ironed with an
ironing cloth to prevent shine marks.
2. Set the desired fabric and
temperature setting. Place the iron
on its heel (on a stable, protected
surface) and allow it to heat for
approximately 2 minutes.
Fig. 4
3. Turn the steam button to the
minimum steam setting. (Fig. 3)
4. With the iron in a horizontal position,
press the burst of steam button
several times to prime the pump.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|