Euro Pro Iron G6118H User Manual

STEAM GENERATOR  
IRON  
OWNER’S MANUAL  
Model G6118H  
120V., 60 Hz., 1500 Watts  
For information or assistance:  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
Tel.: (800) 798-7398  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLSHOOTING  
ADDITIONAL IMPORTANT SAFEGUARDS  
Do not operate the steam generator with a damaged cord, plug or if the iron or any  
other part of the system has been dropped or damaged. To avoid the risk of electric  
shock, do not disassemble or attempt to repair the ironing system. Return the  
appliance to EURO-PRO Operating LLC (see Warranty) for examination and repair.  
Incorrect re-assembly or repair can cause a risk of electric shock or injury to persons  
when the ironing system is used.  
Read all instructions before using the EURO-PRO Operating LLC Steam Generator  
Iron and follow all the instructions and safeguards carefully.  
DO NOT OVER TIGHTEN THE  
BOILER FILLER CAP  
To close the boiler filler cap, turn  
clockwise until the point where you feel  
friction – do NOT close too tightly. The  
boiler filler cap has a gasket which can  
be flattened and damaged if the cap is  
closed too tightly. If the gasket is  
damaged, steam may escape while the  
steam generator is being used. If the  
boiler filler cap is damaged and steam  
is leaking, call customer service to  
purchase a replacement boiler filler  
CAUTION! NEVER open the  
boiler filling cap before ALL  
the remaining steam has been  
released from the steam  
generator and the steam  
generator has cooled. To  
release the steam, press the  
On/Off button to the “Off”  
position and push the steam  
button on the iron until no  
PROBLEM  
POSSIBLE CAUSES  
SOLUTIONS  
1. Press the On/Off button to  
the “ON” position.  
2. Fill with water as per  
instructions.  
3. Make sure that the On/Off  
button is in the “OFF”  
1. On/Off button is not in the  
“ON” position.  
2. Steam generator has no more  
water.  
3. Unit is not plugged in.  
4. Steam is not visible because  
the temperature of the  
soleplate is at maximum and  
room temperature is high.  
5. Generator is not fully heated.  
more steam comes out of the  
iron. Then open the boiler filler  
cap slowly.  
No Steam Is  
Released  
Through The  
Iron  
position and plug the unit  
into an electrical outlet.  
cap.  
4/5. The heating time for the  
generator is approximately  
11-13 minutes. Watch for  
the steam ready light to go  
off indicating that steam is  
ready.  
A WORD ON WATER  
NEVER LEAVE THE HOT IRON  
RESTING ON THE IRON REST  
FOR LONG PERIODS OF TIME  
The lifespan of your steam generator  
will be reduced if the iron is left idle at  
high temperatures for extended  
For best results we recommend using  
100% demineralized/distilled water.  
You can use regular tap water in your  
steam generator, but should the water in  
your area be hard water we strongly  
recommend the use of 100%  
1. Turn the temperature  
control dial to the desired  
setting.  
The Soleplate  
Remains Cold  
1. Temperature is set at  
“Minimum”.  
periods of time. If the iron is not in use,  
reduce the temperature to the lowest  
temperature setting on the temperature  
control thermostat, turn the steam  
generator “Off” and remove the power  
cord from the electrical power outlet.  
demineralized/distilled water. This will  
prolong the life of your generator and  
reduce the frequency of required generator  
cleaning, as well as the possibility of  
staining due to accumulated impurities.  
1. Turn the temperature  
control dial to the marks  
between 2 and 3 dots.  
2. Wait for generator to be  
fully heated.  
Drops Of Water  
Leak From The  
Iron Soleplate  
1. Soleplate temperature is too  
low to iron with steam.  
2. Generator is not fully heated.  
DO NOT USE WATER PROCESSED  
THROUGH A HOME WATER  
SOFTENING SYSTEM OR BOTTLED  
MINERAL WATER.  
WARRANTED FOR REGULAR  
HOUSEHOLD USE  
1. Clean steam generator as  
per instructions.  
2. Use demineralized/ distilled  
water after cleaning the  
tank.  
Dirty Or Yellow  
Steam Is  
Coming Out Of  
The Iron  
1. Residue is water tank.  
2. Not using demineralized/  
distilled water.  
This Steam Generator Ironing system  
is intended for and warranted only for  
normal household use. The iron and/or  
steam generator should not be used  
for more than fifteen (15) hours per  
week in approximately three (3) hour  
intervals.  
DO NOT OVERFILL THE STEAM  
GENERATOR  
When empty, the steam generator can be  
filled with 26 U.S. fl. oz. of demineralized/  
distilled water. Do NOT overfill. Overfilling  
the water tank can cause water drops to  
come out of the steam holes. See filling  
instructions on page 5.  
1. Gasket is broken because  
boiler filler cap was closed too  
tightly or cap was opened  
while tank was full of steam  
and gasket broke.  
Steam Leaking  
From The Boiler  
Filler Cap  
1. Order new boiler filler cap  
from customer service at 1  
(800) 798-7398.  
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS  
CLEANING & MAINTENANCE  
5. Replace the boiler filler cap and  
shake.  
CAUTION! NEVER open the  
boiler filler cap before ALL the  
remaining steam has been  
released from the steam  
generator and the steam  
generator has cooled. To  
release the steam, press the  
On/Off button to the “Off”  
position and push the steam  
button on the iron until no  
more steam comes out of the  
iron. Then open the boiler filler  
cap slowly.  
6. Remove the boiler filler cap and  
empty the tank. Rinse with water two  
to three times by filling, shaking and  
emptying again.  
Even if you have used a steam generator iron before, please read all instructions  
and safeguards in the Use and Care Instruction Book. In addition, please note the  
following user tips:  
6. Wipe the outside of the steam  
generator base with a damp cloth.  
CLEANING THE STEAM  
GENERATOR IRON  
1. Clean the steam generator iron  
ONLY when cold.  
2. Do NOT use scouring pads,  
abrasives or harsh cleansers.  
3. Use a commercially sold soleplate  
cleanser following the manufacturers  
label instructions.  
USING STEAM  
PLEASE NOTE: Steam performance improves after the first 6-8 hours of usage.  
The steam power increases and initial condensation at maximum  
temperature is reduced.  
1. We strongly recommend the use of  
demineralized/distilled water to  
ensure optimum performance and  
maximize the life of your steam  
generator. If you are using  
1. Make sure the temperature setting of the iron is within the steam range on the  
temperature selector.  
2. Turn power on for iron and steam generator. Before starting to use steam,  
make sure the Steam Ready Light is “ON”, indicating that steam is available.  
4. Use a soft damp cloth to wipe the  
outer shell of the iron.  
demineralized/distilled water, the  
steam generator should be cleaned  
once every six (6) to twelve (12)  
months. If you use regular tap water,  
the steam generator should be  
cleaned once a month.  
5. Dry soleplate and iron thoroughly  
after cleaning.  
NOTE: Trying to use steam before the Steam Ready Light is “ON” can cause water  
drops in the steam coming out of the iron.  
STORING YOUR STEAM  
GENERATOR IRON  
CLEARING THE INITIAL CONDENSATION:  
3. Clear the initial condensation by pressing the Steam Button up to 3 seconds.  
Repeat if necessary.  
1. Ensure that the seam generator is  
depressurized by opening the steam  
button on the iron until no further  
steam is escaping.  
2. Always unplug the power cord from  
the electrical outlet when not in use.  
3. Always store in a dry place away  
from the reach of children.  
2. Make sure that all the steam has  
been released from the steam  
generator before doing any cleaning  
or maintenance on the appliance.  
Follow instructions on page 7 for  
releasing the steam.  
3. Remove the power cord from the  
electrical outlet and let the unit cool  
down for at least 4 hours after it has  
been used before starting to clean  
the steam generator.  
IMPORTANT NOTE:  
4. While using the ironing system, if steam has not been released for more than  
approximately 5 minutes, the hose has cooled and any steam remaining in the  
hose from the last use might condense. Clear this condensation by pressing  
Steam Button before proceeding to use the iron.  
4. Always drain the water tank before  
storing.  
5. Always let your steam generator cool  
completely before storing.  
4. NEVER immerse the iron or the  
steam generator in water or any  
other liquid.  
6. Do not let power cord and steam  
hose to touch hot surfaces.  
7. Wrap the power cord and steam  
hose around the appliance loosely.  
CLEANING THE STEAM  
GENERATOR BASE  
1. Make sure that there is no steam  
remaining in the steam generator.  
2. Make sure that the steam generator is  
completely cold.  
3. Remove the boiler filler cap by slowly  
turning counter clockwise to allow any  
remaining steam to escape.  
4. Fill water tank with a solution of 20%  
vinegar and 80% water (5 oz vinegar  
and 21 oz of water) and let sit  
overnight (8-12 hours).  
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS  
GETTING TO KNOW YOUR STEAM GENERATOR  
REFILLING THE STEAM  
GENERATOR  
PRESSING TIPS (cont.)  
Instructions for specific iron  
temperature settings should be  
treated as guidelines only. We  
recommend that you test each type  
of fabric on an inside seam before  
proceeding to iron the garment. The  
steam generator iron can produce  
humid steam at relatively low  
temperature settings where regular  
household irons would release  
water. At the same time, the very dry  
steam produced at the high iron  
temperature setting “•••” can be used  
on some fabrics where normally the  
use of steam is prohibited.  
WARNING! Never direct the  
steam from the iron at yourself  
or another person. Special care  
must be taken when the iron is  
used in a vertical position. The  
steam is very hot and can  
cause burns.  
1. Press the steam generator On/Off  
button to the “OFF” position.  
2. Release all the remaining steam in  
the steam generator by pressing the  
steam button until no more steam is  
coming out from the iron.  
3. Unplug the appliance from the wall  
outlet. Allow it to cool for a minimum  
of 5 minutes.  
4. To unscrew the boiler filler cap, push  
down and turn counter clockwise  
slowly. If any steam continues to  
escape, STOP and release the  
steam through the iron as in the  
steps above.  
PRESSING DIFFICULT FIBERS  
(i.e. 100% COTTON)  
Your Steam Generator Iron features  
steam holes placed in the front of the  
iron soleplate. Correct ironing  
procedure involves steaming the  
fabric with the front end of the iron  
followed by pressing and drying with  
heat from the rear of the iron. For  
best results, garments should be dry  
after pressing to avoid re-wrinkling  
due to lingering dampness.  
5. Using a measuring cup, fill the water  
tank with 26 US fl. oz.  
6. Replace the boiler filler cap turning  
clockwise until you get friction. DO  
NOT OVERTIGHTEN OR GASKET  
WILL BE FLATTENED.  
Therefore, we recommend that you  
use the steam as required, but not  
continually.  
PRESSING TIPS  
While your Steam Generator Iron  
offers high quality type steam, some  
fabrics may require additional  
moisture for best results. You may  
want to press cotton shirts while still  
damp or spray with water prior to  
ironing.  
Dry Steam vs Humid Steam  
In a steam generator iron the steam  
is produced in the generator and not  
in the iron as with regular household  
irons. The temperature of the iron  
determines the type of steam – dry  
or humid. At high temperatures, the  
iron delivers very dry steam. Lower  
temperature settings offer humid  
steam.  
1. Boiler Filler Cap  
7. Steam Hose  
8. Steam Button  
9. Temperature Ready Light  
10. Temperature Control Dial  
11. Stainless Steel Soleplate  
2. Steam Ready Light (green)  
3. On/Off Button (red)  
4. Steam Generator Base  
5. Iron Rest Plate  
For best pressing results, you have  
the flexibility to select the type of  
steam and not only the iron  
6. Power Cord  
temperature. A balance should be  
maintained between the humidity  
(low iron temperature) required to  
loosen fibers and the need for heat  
(higher iron temperatures) to  
Technical Specifications  
Voltage:  
Power:  
120V., 60Hz.  
1500 Watts  
flatten/shape and dry the fibers.  
Water Capacity:  
26 US fl. Oz.  
Working Pressure: 2.9 bar  
4
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
This appliance is for HOUSEHOLD USE  
6. Press the On/Off button on the  
stream generator to the “ON”  
position.  
7. Turn the temperature control dial on  
the iron to the desired temperature  
setting.  
DRY IRONING  
1. Place the steam generator on a flat  
stable surface.  
TEMPERATURE SETTINGS  
ONLY and may be plugged into any  
120V AC polarized electrical outlet. Do  
not use any other type of outlet.  
Always read the garment labels and  
follow the manufacturer’s directions  
when pressing a garment.  
2. Plug the power cord into an  
electrical outlet and press the On/Off  
button to the “On” position.  
3. Set the temperature control dial  
according to the garment label or  
use the temperature guide below.  
4. The temperature ready light will go  
“OFF” when the desired temperature  
has been reached.  
For maximum efficiency, iron  
garments requiring lowest  
BEFORE FIRST USE  
Remove any labels, stickers or tags  
which may be attached to the body or  
the soleplate of the iron before using  
the steam generator.  
temperature setting first as the iron  
heats up faster than it cools down.  
If there are no instructions included  
with the garment, we suggest that  
you follow the temperature guide on  
page 6 as a guide (except when any  
fabric has an applied finish, gloss,  
etc. where lower temperatures might  
be required.  
Always iron fabric blends, (fabrics  
made of two or more types of fibers)  
using the heat setting appropriate for  
the fabric requiring the lowest  
temperature setting.  
Temperature  
Control  
Dial  
WARNING! Never leave the  
unit unattended while plugged  
in. Always turn the steam  
generator “OFF” and remove  
the power cord from the  
electrical outlet.  
5. You can iron at any temperature  
setting without steam.  
USING THE IRON WITH STEAM  
1. Place the steam generator on a flat  
stable surface.  
2. Fill the steam generator with water.  
3. Plug the power cord into an electrical  
outlet.  
WARNING! The steam  
generator must always be  
turned “OFF” and  
4. Press the On/Off button to the “ON”  
position. The steam ready light will  
light up when the steam is ready.  
It will take approximately 11-13  
minutes to heat up a full tank of  
water. The steam ready light will  
go on and off while the steam  
generator is in use.  
5. Turn the temperature control dial to  
the desired temperature setting  
designated for use with steam, i.e.  
between the two “••” and the three  
“•••” dots on the temperature control  
dial. The temperature ready light will  
light up. The iron will have reached  
the desired temperature setting  
when the temperature ready light will  
go off.  
NOTE: For best results, make sure that  
the steam generator is filled to the  
maximum level before every use.  
disconnected from the  
electrical outlet before any  
cleaning or maintenance;  
before filling and emptying the  
water tank.  
IRONING TEMPERATURE GUIDE  
FILLING STEAM  
GENERATOR WATER TANK  
Check garment labels for instructions i.e. do not iron chlorofiber  
SUGGESTED  
1. Place steam generator unit on  
a solid flat surface.  
FABRICS  
TEMPERATURE RANGE  
AMOUNT OF  
STEAM  
2. Unscrew the boiler filler cap.  
3. When filling the steam  
generator water tank, always  
use a measuring cup to fill  
your unit. NEVER fill the  
appliance under a tap. Fill the  
water tank with 26 US. fl. oz.  
of tap water if the water in  
your area is not hard water. If  
it is, then we strongly  
SYNTHETIC:  
Acetates, Acrylics  
Cresian, Metalics  
Sheer Synthetic  
Polyester, Dacron  
Dry Ironing  
(without steam)  
Fortrel,  
6. Press the steam button on the  
handle of the iron to release the  
steam.  
Perma Press, Nylon  
recommend using 100%  
demineralized/distilled water.  
Be careful not to over fill the  
water tank. Adding too much  
water will cause overfilling  
and will result in water drops  
on the steam.  
Note: Trying to use steam before the  
steam ready light has come on can  
cause water drops to come out of  
the iron instead of steam.  
Pure silk sometimes  
requires steam  
Silk  
Wool  
Humid Steam  
WARNING! Never direct the  
steam from the iron at yourself  
or another person. Special care  
must be taken when the iron is  
used in a vertical position. The  
steam is very hot and can  
cause burns.  
4. When finished filling, replace  
the boiler filling cap and screw  
on tightly.  
Cotton  
Linen  
Normal Steam  
5. Plug the power cord into an  
electrical outlet.  
Super Dry Steam  
MAX  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edelbrock Automobile Parts Non EGR for Chevrolet 90 V6 User Manual
Eiki Computer Drive WL 10 User Manual
Fellowes Mouse 9893501 User Manual
First Alert Home Security System FA134OC UL User Manual
Ford Automobile 2010 Mustang User Manual
FujiFilm Digital Camera 106 8620 User Manual
FUNAI CRT Television CR202EM9 User Manual
GBC Laminator Catena 35 User Manual
GE Dishwasher GDF520PGDBB User Manual
Giant Bicycle METHOD 16 User Manual