MUSIC | AUDIO POST | VIDEO | FILM
Artist Series
professional control surface
USER GUIDE
Document Revision: B
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Canada
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada
European Union
Australia
ABN 91 051 557 905
Japan
iii
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
IMPORTANT SAFETY INSTRUCTIONS
The lighting flash with arrowhead symbol within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electrical shock
to persons.
The exclamation point within an equilateral triangle, is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
iv
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) This product must be connected to an AC power source that provides a safety earthing
connection. This unit is provided with a power supply cord set appropriate for your
area. Do not modify or defeat the safety earthing feature of the power cord.
10) Protect the power cord from being walked on or pinched particularly at plugs, conve-
nience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the appa-
ratus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate normally, or has been dropped.
15) WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
16) Do not expose this equipment to dripping or splashing and ensure that no objects filled
with liquids, such as vases, are placed on the equipment.
17) To completely disconnect this equipment from the AC Mains, disconnect the power
supply cord plug from the AC receptacle.
18) The mains plug of the power supply cord shall remain readily operable.
19) Operator Accessible Fuse (UK only):
Caution: For continued protection against risk of fire, replace only with same type
and rating of fuse.
Attention: Pour ne pas compromettre la protection contre les risques d’incendie,
remplacer par un fusible de même type et de même caractéristiques
nominales.
v
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Table of Contents
List of Figures ........................................................................................................ ix
Chapter 1: Introduction to the Artist Series..................................................... 11
Chapter 2: Setup and Installation ..................................................................... 13
2.2 Installation................................................................................. 16
Chapter 3: Common Tasks.................................................................................. 21
Chapter 4: Surface Controls ............................................................................... 25
4.2 Shift Key .................................................................................... 26
vii
4.3.2 Fader............................................................................. 28
4.3.3 ON................................................................................. 28
4.3.4 SOLO............................................................................. 28
4.3.6 SEL................................................................................ 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Artist Series
professional control surface
4.5 Knobs ........................................................................................ 33
Chapter 5: EuControl...........................................................................................41
5.3 General ......................................................................................45
viii
5.5 Assign........................................................................................48
Appendix A: Setting the IP Address..................................................................... 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Artist Series
professional control surface
List of Figures
Menu bar with EuControl icon ....................................................................... 16
2-10 FOOTSWITCH input on rear panel .................................................................. 19
Strip 1 fader SEL key .................................................................................... 21
NUDGE and BANK keys ................................................................................. 22
Shift keys ..................................................................................................... 22
BACK and PAGE keys .................................................................................... 24
Fader navigation controls ............................................................................. 31
Channel mode .............................................................................................. 34
ix
4-10 Flip indicator in OLED display ........................................................................ 34
4-11 Knob Selector keys ....................................................................................... 35
4-12 Knob Set navigation keys .............................................................................. 37
General tab .................................................................................................. 45
Preferences tab ............................................................................................ 46
Assign tab .................................................................................................... 48
Layouts tab .................................................................................................. 49
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Chapter 1: Introduction to the Artist Series
The MC Mix and MC Control comprise the Artist Series desktop control surfaces.
They use a 100 Mbs Ethernet EuCon connection to control audio/video applications
running on a workstation computer. EuCon is a high-speed communication
protocol and enables control of virtually every application feature.
The MC Mix and MC Control can each run as standalone devices and up to four
MC Mixes can be used, with or without an MC Control, to create a larger control
surface. The Artist Series borrows many features from the Euphonix MC Pro and
System 5-MC.
11
Figure 1-1 MC Control and MC Mix
The MC Mix supports two types of applications:
•
EuCon-aware applications (i.e., Nuendo, Logic Pro) are written to directly
support the EuCon protocol. They provide the highest level of integration,
high-resolution controls, and high-speed connectivity.
•
Non-EuCon-aware applications that support Mackie Control or HUI (i.e., Pro
Tools, Final Cut Pro and Digital Performer) can control many functions but
are less integrated than EuCon-aware applications.
The MC Control can provide some functionality over non-EuCon-aware applications
that do not support HUI or Mackie Control by sending out keystroke commands
over EuCon.
EuControl Software
The EuControl software application is responsible for finding, linking, and
communicating with all MC Mixes and MC Controls on the network. EuControl
must be installed on the workstation computer that runs the applications before
using the Artist Series devices.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Conventions Used in this User Guide
The User Guide refers to all functions labeled on the MC Mix surface and rear
panel with all caps in bold type (i.e., NUDGE X, PAN, SEL, SOLO).
The Shift key is used in conjunction with other keys to access secondary functions
labeled in blue above the primary function. Two Shift keys are located at the MC
Mix’s bottom-left and -right. To describe Shift functions simply, “press and hold
the Shift key then press the AUX key” is written as “press the GROUP key.”
Track refers to an application’s track, while fader strip or strip refers to the MC
Mix’s hardware fader strip.
How to Use the PDF
The Acrobat PDF version of this manual can be a valuable online help learning
tool while using the MC. These are some useful features of the PDF:
•
•
The Bookmarks on the left serve as a continuously visible table of contents.
Click on a subject heading to jump to that page. Click a + symbol to expand
that heading to show subheadings. Click the
-
symbol to collapse a sub-
heading.
12
The manual’s table of contents and list of figures are active links to their
pages. Select the hand cursor, allow it to hover over the heading until it
turns into a finger. Then click to locate to that subject and page.
•
•
All cross references are active links. Allow the hand cursor to hover over the
reference until it turns into a finger and click to follow the reference.
Use the left and right arrow keys on the bottom bar to go back and forth
between views. This is a great way to follow a cross reference and return to
the page from which you were reading.
•
•
Select the Find item from the Edit menu (Ctrl-F) to search for a subject. This
can be used as an “index on the fly.”
Use the magnifying glass tool or the zoom edit box on the top bar to zoom
in/out. This is helpful when examining a complex graphic or setting the text
size for easy reading online.
Acrobat Reader version 6 or later is required to open the PDF. This can be down-
loaded for free from:
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Chapter 2: Setup and Installation
Euphonix is dedicated to making your MC Mix experience enjoyable and trouble-
free so we will periodically update the following software and documentation:
•
EuControl: This software runs your MC Mix and communicates to your audio/video
application. Always download the new version if prompted to do so when you launch
EuControl.
•
•
MC Mix User Guide (PDF): This is the complete user guide for your MC Mix and the
document you are currently reading.
EuCon Application Setup Guide (PDF): The MC Mix supports many applications, each
with a slightly different setup procedure. This document includes supplementary
instructions for each application.
Before proceeding, download the latest versions from:
2.1 Setting Up the MC Mix
Unpack your MC Mix, power adapter, AC power cord, installation CD, Ethernet
crossover cable, and riser brackets from its box.
13
2.1.1
Elevating the MC Mix
The MC Mix can be elevated or angled using small foldout legs on the bottom of
the unit or elevated and angled by attaching the larger riser brackets. Since either
method requires turning the MC Mix over, it is easier to do this before attaching
any cables. Turn it over and place it on a soft surface.
Pull out all four of the small foldout legs to moderately elevate the unit; pull out
Foldout
leg
Riser
bracket
Figure 2-1 Foldout leg (left); riser bracket (right)
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Two larger, detached riser brackets elevate and angle the unit more than the
foldout legs. Use moderate force to snap them into the bottom panel as shown
To remove the riser brackets:
Figure 2-2 Removing side panels (left); removing riser brackets
3. Lift the riser bracket out of the MC Mix to remove
Physically Linking Artist Series Devices
14
2.1.2
MC Mixes can be physically attached to each other to form a larger, stable control
page 41 to use EuControl to link the surfaces in the desired order.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
To join two MC Mixes:
1. On one of the MC Mixes, use a #2 Phillips screwdriver to remove the two silver
The screws may be tight, so you may have to use some force.
Figure 2-3 Removing screws from the bottom panel
2. Lift the black plastic connecting part and side panel up and out of the MC
15
Figure 2-4 Removing connecting part and side panel
end where it will attach to the first MC mix.
4. Slide the connecting part of the second MC Mix into first MC Mix to attach
Figure 2-5 MC Mixes attached by connecting at side panel
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
2.2 Installation
1. Insert the installation CD into your Macintosh or, if you downloaded the latest
software from the web, double-click on the installer. Follow the instructions
to install the software.
If prompted to download the most current version of EuControl, follow the
onscreen instructions.
EuControl will launch automatically and is running when this icon appears
in your menu bar.
EuControl
icon
Figure 2-6 Menu bar with EuControl icon
2. Shut down your Macintosh.
and the other into a power outlet.
16
power adapter
CH
IT
W
TS
O
FO
V
DC In 15
AC power cord
DC output
cable
Figure 2-7 Connecting the power adapter
4. Connect the DC output cable from the power adapter to DC In on the left side
of the rear panel (Figure 2-7 right).
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
5. Plug one end of the Ethernet crossover cable into the Ethernet jack (labeled
with
E u
c
o n
Ethernet
cable
Figure 2-8 Ethernet cable and rear panel jack
6. Plug the other end of the Ethernet crossover cable into an open Ethernet
An Ethernet router or switch is required to connect additional MC Mix units
or to a local area network. Note that connecting directly to the computer
(Figure 2-9-right) may require removing your Internet cable.
17
Figure 2-9 MC Mix connected to router (left) and directly to computer (right)
7. Turn on your router (if applicable), then turn on your Mac and wait until it
finishes starting up.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
8. Press and release the POWER switch on your MC Mix.
Look at the top-right of your screen and wait up to 60 seconds. A green icon
in the menu bar indicates correct installation.
If you did not see the green icon:
• If your Mac is pre-2002 and you are using an Ethernet router or switch,
you need to purchase a normal straight-through Ethernet cable (instead
of the crossover Ethernet cable supplied) from a computer store.
shooting information.
9. Launch your application and open a project (Logic, Cubase, Digital Performer,
Pro Tools, etc.).
10. To set up your application to work with the MC Mix, refer to the EuCon Ap-
plication Setup Guide that you downloaded at the beginning of this section.
Logic users do not need this document because additional setup is not
required.
18
Controlling a Second Workstation
The MC Mix can control applications running on a second computer, referred to in
this guide as a workstation. Most users will not need to do this because EuControl
will be running on the same workstation as the their audio/video applications.
Insert the installation CD into your Macintosh or, if you downloaded the latest
software from the web, double-click on the installer. Follow the instructions to
install the software.
Copy the latest software that you downloaded at the beginning of this chapter
over to the second workstation. Double-click the Install EuCon Workstation installer
in the Extras folder and follow the instructions to install the EuCon software.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Connecting a Footswitch
The MC Mix has a ¼-in FOOTSWITCH input on the rear panel. The footswitch can
be used to punch in and out of recording. Plug the footswitch in before powering
CH
SWIT
T
FOO
FOOTSWITCH
input
V
DC In 15
Figure 2-10 FOOTSWITCH input on rear panel
19
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Chapter 3: Common Tasks
start learning about your MC Mix. We recommend performing these simple tutorials
of common tasks in the order presented.
Fader Strip
The corresponding track is selected in your application.
2. Move the MC Mix’s strip 1 fader up and down.
You are now controlling the level of your application’s first track with your
MC Mix. The display at the top of strip 1 shows track information.
CFG
CFG
SOLO
ON
PAGE
PAGE
FLIP
CHAN
12
6
21
AUTO
REC N
INPUT
INSERTS
0
5
DYN
EQ
ASSIGN
SEL Y
10
GROUP
AUX
20
30
fader
SEL key
PAN
key
MIX
PAN
40
60
Figure 3-1 Strip 1 fader SEL key
3. When the MC Mix is first powered up, the PAN key is lit by default. If it is not
Each strip’s Soft Knob now controls pan for its application’s corresponding
track.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
If tracks 1–8 were assigned to strips 1–8, tracks 2–9 are now assigned to
strips 1–8.
SEL
MIXER
CLOSE
NUDGE
NUDGE
ON
HOME
BANK
END
SOLO
ON
BANK
PLAY
REC
Figure 3-2 NUDGE and BANK keys
The Shift key is used in conjunction with other keys to access secondary
functions labeled in blue above the primary function. In this case, the HOME
function is accessed by pressing Shift + BANK W.
Two Shift keys are located at the MC Mix’s bottom-left and -right.
22
40
60
40
60
40
60
40
60
40
60
40
60
40
60
40
60
MC MIX
Shift key
Shift key
Figure 3-3 Shift keys
If tracks 1–8 were assigned to strips 1–8, tracks 9–16 are now assigned to
strips 1–8.
NUDGE W and BANK W keys perform the same operations in the opposite di-
rection.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Inserts
1. Add a plug-in on track 1 of your application.
to restore tracks 1–8 to strips 1–8.
SEL
Soft
Knob
TOP
BACK
ON
CFG
CFG
SOLO
ON
PAGE
PAGE
CHAN
key
FLIP
12
6
CHAN
AUTO
REC N
INSERTS
key
INPUT
INSERTS
0
5
DYN
EQ
fader
SEL key
23
ASSIGN
SEL Y
10
GROUP
AUX
Figure 3-4 Fader strip, INSERTS and CHAN keys
The names of the plug-ins on that track spill across the display screens.
The Soft Knobs can be turned like a conventional knob and pressed like a
switch to access an additional function.
The parameters of that plug-in spill across the display screens.
7. Turn the Soft Knob below the desired parameter to adjust its value.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Chapter 4: Surface Controls
ION
ION
T
T
A
T
A
S
IC
P
OR
P
W
A
8
8
8
8
O
N
Y
UT
A
S
SEL
REC
A
O
N
Y
UT
A
S
SEL
REC
A
O
N
Y
T
L
U
A
S
SE
REC
A
25
O
N
Y
T
L
U
A
S
SE
REC
A
8
8
8
8
O
N
Y
T
L
U
A
S
SE
REC
A
O
N
Y
T
L
U
SIG
A
S
SE
REC
A
O
N
Y
L
UT
A
S
SE
REC
A
O
N
Y
L
UT
A
S
SE
REC
A
Figure 4-1 MC Mix surface controls
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.1
4.2
Power Switch
Press and release the POWER switch to turn the MC Mix on/off.
•
•
All displays shows a Euphonix logo upon power up.
All activity on the displays and LEDs ceases upon power down.
Shift Key
The Shift key is used in conjunction with other keys to access secondary functions
labeled in blue above the primary function. Two Shift keys are located at the MC
Mix’s bottom-left and -right.
The following simplified terminology is used describe Shift functions:
“Press and hold the Shift key then press the AUX key”
is written as
“press the GROUP key”
26
The Shift key can be locked on like caps lock on a computer keyboard by pressing
both Shift keys simultaneously. This is useful if you plan to access several Shift
functions consecutively. Press either Shift key to unlock.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.3
Fader Strips
The MC Mix provides eight fader strips, each with a touch-sensitive fader and a
touch-sensitive knob, that control tracks in an audio or video application.
4.3.1
Display Screens
At the top of each fader strip is a 128 x 64 pixel Organic Light Emitting Diode
(OLED) display that shows the following items:
attention
indicator
track
name/value
5.1-channel
meter
meter
knob
name/value
with peak
automation mode
knob position
Figure 4-2 Fader display indicators
Meter shows clip, peak, and normal values. It can show mono, stereo, or surround
sound tracks.
27
Track name shows the name of the track. When a fader is touched, it shows the
value of the fader. After releasing the fader it reverts to showing the track name.
Knob name shows the name of the parameter currently on the knob. When a
knob is touched, it shows the value of the parameter. After releasing the knob it
reverts to showing the parameter name.
Knob position graphically shows the value of the knob.
Auto mode shows the track’s automation mode (blank = neither read nor write,
r = read, w = write, rw = read/write).
Attention indicator is a line under the track name that shows this strip contains
OLED Dimming
To preserve OLED life, the channel displays dim when not in use. The time until
dimming begins can be set in Preferences on page 51.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.3.2
Fader
The fader controls the track assigned to this strip. It is motorized so it reflects
changes made in the application, such as automation. It is also touch sensitive,
which some applications use when automating.
SOLO
ON
12
6
AUTO
REC N
0
5
ASSIGN
SEL Y
10
20
30
28
40
60
Figure 4-3 Fader strip
fader selects that track in the application and attentions it on that strip. This is
the same as pressing the fader Sel key.
4.3.3
4.3.4
ON
The track is on (unmuted) when the strip’s On key is lit and off (muted) when the
strip’s On key is not lit.
SOLO
The SOLO key lights red when that strip’s track is soloed and is unlit otherwise.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.3.5 Transport Controls
SOLO
RTZ
ON
SOLO
NEXT
ON
SOLO
FF
ON
SOLO
PLAY
ON
PREV
REW
STOP
REC
Figure 4-4 Transport Controls
RTZ
Press RTZ (Return To Zero) to move to the beginning of the project.
PREV
Press PREV to move to the previous marker. Not all applications support markers.
NEXT
Press NEXT to move to the next marker. Not all applications support markers.
REW
Press REW to rewind. This function varies with the application.
29
Implementations include:
•
Rewind until STOP or another key is pressed.
Rewind a fixed amount.
•
•
Rewind until the REW key is released.
FF
Press FF to fast forward. This function varies with the application.
Implementations include:
•
•
•
Fast forward until STOP or another key is pressed.
Fast forward a fixed amount.
Fast forward until the FF key is released.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
STOP
Press STOP to stop all other functions.
PLAY
Press PLAY to play the project from the current location.
REC
Press REC begin recording at the current location. All tracks armed for recording
are punched into record.
4.3.6
SEL
Pressing a fader’s SEL key selects that track in the application and attentions
NOTE: Some applications allow selecting multiple tracks if the Shift key on the work-
station is held down while selecting tracks. In this case, the attentioned track
is the last one selected.
30
4.3.7
4.3.8
ASSIGN
Press the ASSIGN key to display the Assign tab in the EuControl Settings dialog
REC
Press the REC key to enable recording on a track. The REC key lights red to indicate
that track is enabled (armed) for recording. Press the REC key to cancel a track
enabled for recording.
NOTE: Some applications blink the REC LED when armed but not recording and light
solid when recording.
4.3.9
AUTO
To change an application track’s automation mode, press the AUTO key until the
desired automation mode appears in the channel display.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.4
Fader Navigation Controls
Scroll through the application’s tracks using the BANK and NUDGE keys. HOME
and END are shortcuts to the first and last banks, respectively.
SEL
MIXER
CLOSE
NUDGE
NUDGE
ON
HOME
BANK
END
SOLO
ON
BANK
PLAY
REC
Figure 4-5 Fader navigation controls
4.4.1
BANK and NUDGE
The BANK and NUDGE keys change which tracks are assigned to the strips. The
eight strips can be thought of as a window that moves in the direction indicated
by the arrow over the application’s tracks (Figure 4-6).
31
Window
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Strips
Figure 4-6 Strips window moves over application tracks
NUDGE W
Moves the window one track to the left. If strips 1–8 had tracks 9–16, they now
have tracks 8–15.
NUDGE X
Moves the window one track to the right. If strips 1–8 had tracks 9–16, they now
have tracks 10–17.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
BANK W
Moves the window one bank (eight tracks) to the left. If strips 1–8 had the bank
starting at track 9, they now have the bank starting with track 1. Pressing
BANK W again does nothing because the first bank is already shown.
BANK X
Moves the window one bank (eight tracks) to the right. If strips 1–8 had the bank
starting at track 9, they now have the bank starting with track 17.
4.4.2
MIXER and CLOSE
Not all applications support these keys.
MIXER
Opens and closes the application’s mixer window.
CLOSE
Closes any open window or dialog box on the application.
4.4.3
4.4.4
HOME and END
32
HOME
Moves to the first bank with tracks 1–8 assigned to strips 1–8.
END
Moves to the last bank.
Navigating Among Multiple MC Mixes
Multiple MC Mixes act as one big control surface with a bank size of eight tracks.
For example, three linked MC Mixes can show 24 contiguous tracks. The BANK
and NUDGE keys perform the identical actions on the combined set of tracks.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.5
Knobs
Each fader strip has one touch-sensitive, continuously rotating knob that adjusts
parameters such as pan and aux send levels. The knob has a built-in switch
allowing it to be pressed from the top. This is called the Knob Top key and is
typically used to access sub-menus but also to turn parameters on/off.
Knob SEL key
SEL
Touch-sensitive knob
ON
Knob On key
Figure 4-7 Knob controls
Each knob has the following controls:
•
•
The ON key toggles two-state parameters, such as EQ Band 1 on/off.
The SEL key changes the knob function or toggles a secondary function’s
value, such as an aux send pre/post fader.
33
4.5.1
Basic Knob Use
When the MC Mix is first powered on, the knobs are in normal mode (see Knob
on the strip.
The knob selector keys can quickly access common parameters in normal mode:
•
Press AUX to assign each track’s first aux send to each knob. Press PAGE X
to assign the next aux send to the knob. Pressing PAGE W returns to the
previous aux send.
•
Press PAN to assign the track’s left/right pan control to each knob.
It is also possible to edit plug-ins, EQ, dynamics, and other functions on the
knobs.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.5.2
Knob Modes
The eight knobs can be in normal or channel modes.
Normal Mode
Each knob controls the same parameter for every track on the strips.
Figure 4-8 Normal mode
Channel Mode
Channel mode is useful for editing EQs and plug-ins that have many parameters.
The eight knobs control up to eight different parameters on a single attentioned
denoted in the OLED display by a grid of small yellow dots around each parameter
name and knob position indicator. The attentioned track is further distinguished
by these dots around its entire area including the track name (Figure 4-9).
34
attentioned track
Figure 4-9 Channel mode
CHAN Key
The CHAN key toggles between normal (CHAN key unlit) and channel mode (CHAN
show which track’s parameters will be expanded in channel mode (Figure 4-9).
FLIP Key
The FLIP key toggles the fader controls to the knobs and vice versa. A vertical
double arrow appears in the OLED display when the faders and knobs are
flipped. Press the FLIP key again to toggle the faders and knobs back to normal.
Flip indicator
Figure 4-10 Flip indicator in OLED display
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.5.3 Knob Set Selector Keys
A knob set is an array of knobs used by EuCon applications to control plug-ins,
EQs, dynamics, aux sends, etc. One of the eight Knob Set Selector keys is always
selected and lit and displays its knob set until another Knob Set Selector key is
pressed. When the MC Mix first starts, the PAN knob set is selected by default.
INPUT
INSERTS
DYN
EQ
GROUP
AUX
MIX
PAN
Figure 4-11 Knob Selector keys
The Knob Set Selector keys enter the MC Mix menu system. Some of these knob
sets can display another knob set called a sub-menu. For example, the Inserts
knob set shows the names of every plug-in inserted on the track, one plug-in
name per knob (in channel mode). Pressing a plug-in’s Knob Top key displays its
parameters on the knobs for editing. This new knob set is a sub-menu of the
knob set.
35
Sub-menus are not directly supported in normal mode. When a sub-menu is
entered in normal mode, the MC Mix automatically changes to channel mode
and that track is attentioned and selected. When the top of that knob set is
displayed again, normal mode resumes. Since sub-menus can be more than one
the BACK key repeatedly. However, you can simply press another Knob Selector
key to navigate directly to another knob set.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
INSERTS
Pressing the INSERTS key displays the inserts knob set for editing plug-ins. In
normal mode, the first plug-in is displayed on the knob. Pressing one of these
Knob Tops in normal mode toggles the MC Mix into channel mode and displays
the first eight plug-in parameters for editing. Pressing a plug-in’s Knob Top
displays its parameters for editing.
EQ
Press the EQ key to display the EQ knob set to configure equalization controls
and filters. This automatically toggles the MC into channel mode and shows four
EQ bands on eight knobs.
AUX
Press the AUX key to display the Aux knob set to control auxiliary sends. In normal
mode, the first aux send is displayed. In normal mode, press the PAGE X key to
advance to the second aux send. In channel mode, up to eight aux sends can be
shown at once.
PAN
Press the PAN key to display the Pan knob set to configure left/right or surround
panning. In normal mode, the left/right pan control is typically displayed. In
channel mode, the first page of eight pan knobs is shown.
36
INPUT
Press the INPUT key to display the Input knob set to configure input routing, mic
gains, phantom power, and other application-specific parameters.
DYN
Press the DYN key to display the Dynamics knob set to configure compressors,
limiters, expanders, and gates.
GROUP
Press the GROUP key to display the Group knob set to configure group bus routing
or control group (VCA) membership.
MIX
Press the MIX key to display the Mix knob set to configure output routing.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
4.5.4
Dual-Function Knobs
Some knobs have two functions that are toggled by pressing the knob’s SEL key
(i.e., EQ Frequency and Q). The knob name changes in the display to show the
current function. Dual-function knobs are supported in normal mode.
4.5.5
Knob Set Navigation Keys
Since a knob set may have more parameters than knobs, the PAGE W and
PAGE X keys scroll among them.
SEL
TOP
BACK
ON
CFG
CFG
SOLO
ON
PAGE
PAGE
Figure 4-12 Knob Set navigation keys
PAGE W
37
Press the PAGE W key to scroll to the previous page. When on the first page,
pressing PAGE W key does nothing. The PAGE W key lights yellow when there is
a previous page to go to.
PAGE X
Press the PAGE X key to scroll to the next page. When on the last page, pressing
the PAGE X key does nothing. The PAGE X key lights yellow when there is a next
page to go to.
Configuration Pages (CFG)
Many knob sets have a configuration page to set up that knob set. The configu-
ration page for the Inserts knob set, for example, is used to assign plug-ins to a
track. The configuration page for the Aux knob set assigns aux sends to a track.
Some applications can configure presets for plugins and EQs.
Press the PAGE W + PAGE X keys simultaneously to display a knob set’s config-
uration page, if it has one. When on the configuration page, both the PAGE W
and PAGE X keys light.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
NOTE: Configuration pages work only in channel mode.
38
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
BACK
Press the BACK key once to return to the previous knob set. Press the BACK key
repeatedly to back out of all sub-menus and display the top of the current knob
set.
TOP
Press the TOP key to immediately back out of all sub-menus and display the top
of the current knob set. This is equivalent to pressing the BACK key repeatedly.
4.5.6
Knob Sets and Multiple MC Mixes
Press the CHAN key on any MC Mix to toggle all surfaces between normal and
channel mode.
In channel mode, a knobset is displayed across all linked surfaces. For example,
with two linked surfaces, a knobset is displayed on 16 knobs instead of eight. If
the knobset has more knobs than the linked surfaces can display, navigate
among them with the PAGE keys.
39
Press a Knob Set Selector key on any MC Mix to select that knob set on all MC
Mixes.
4.6
4.7
APPLICATION
Press the APPLICATION key to toggle between the two most recently used open
applications. Hold down the APPLICATION key and press BANK X to toggle
between all open applications in a circle. Hold down the APPLICATION key and
press BANK W to cycle through applications in the opposite direction.
WORKSTATION
The MC Mix can control applications running on a second computer, referred to
in this guide as a workstation. Press the WORKSTATION key to attach the MC Mix
to another workstation. You must first use EuControl to create a list of workstations
While attached to a second workstation, your Mac’s keyboard and mouse can be
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
40
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Chapter 5: EuControl
EuControl is launched automatically upon starting your Mac and runs in the
background. EuControl is responsible for finding, linking, and communicating
with all MC Mixes and MC Controls on the network. EuControl’s configuration
tasks are accessed by clicking the green icon
on the Mac taskbar and selecting
EuControl Settings.
Only one instance of EuControl can run on a workstation. However, multiple work-
stations on a single network can each run EuControl. Each instance of EuControl
can connect up to four MC Mixes on the network. These multiple MC Mixes act
together as a single control surface. Once connected, these MC Mixes are not
available to other instances of EuControl until relinquished.
41
Figure 5-1 Selecting EuControl Settings from the taskbar
The tabs are discussed in the order (left to right) they appear at the top of the
EuControl Settings dialog.
5.1
Surfaces
The Surfaces tab shows all MC Mixes on your network and the MC Mixes connect-
ed to your instance of EuControl.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Figure 5-2 Surfaces tab
All Surfaces
42
All Surfaces shows all MC Mixes on the network. An MC Mix shown in light gray
is already connected either to your own or another instance of EuControl run-
ning on a different workstation. In both cases, it is not selectable.
My Surfaces
My Surfaces shows the MC Mixes connected to your instance of EuControl. If there
is more than one MC Mix in this list, they are linked into a single large surface.
The top-to-bottom order corresponds to the left-to-right order of the surfaces,
respectively. The leftmost MC Mix has fader strip 1. Use the
to reorder the list.
and
buttons
Each MC Mix can be renamed by double-clicking the existing name and typing a
new name.
Add B
Click Add B to add the selected All Surfaces entry to My Surfaces. This connects
this MC Mix to your instance of EuControl. You can also click and drag an MC Mix
from All Surfaces to My Surfaces.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Add B is disabled if all MC Mixes in All Surfaces are connected to any instance
of EuControl.
Remove
Click Remove to remove the selected surface from My Surfaces and make it
available to other instances of EuControl.
Remove is disabled if no surface is selected.
Show Info
Select an MC Mix and click Show Info to display the name and hardware/soft-
ware information on strip 1’s channel display and in a dialog on the Mac.
5.2
Workstations
The MC Mix can control applications running on a second computer, referred to
in this guide as a workstation. The Workstations tab establishes the list of work-
stations that the WORKSTATION key cycles through. Any workstation running
EuCon software can be in this list, including those controlled by the System 5-MC,
MC Pro, and MC Control.
43
Figure 5-3 Workstations tab
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
All Workstations
All Workstations lists all EuCon-enabled workstations on the network. If the
workstation is already in the My Workstations list, it is shown in gray and cannot
be selected.
My Workstations
My Workstations lists the workstations that can be attached to by pressing the
WORKSTATION key.
It is possible to put a workstation in the My Workstations list that is already
attached to another instance of EuControl running on another computer. It
cannot be attached here until it is unattached from the other instance of EuControl.
This was done to allow multiple users to share workstations without having to
frequently edit their My Workstation list.
Add B
Click Add B to add the selected workstation from the All Workstations list to the
My Workstations list. If the workstation is already in the My Workstations list, it
is gray and cannot be selected.
44
Remove
Click Remove to remove the selected workstation from the My Workstations list.
Attach/Detach
Select a workstation in the My Workstations list and click Attach. A check mark
appears in the Attach column next to that workstation. This workstation is now
communicating with the MC Mix(es) connected to your instance of EuControl.
If the selected workstation is already attached, the button displays Detach.
Redirect keyboard and mouse control to attached external workstation
Your Mac’s keyboard and mouse can control a second external workstation, if
desired. Select this option to redirect keyboard and mouse control to the attached
workstation. Note that the keyboard and mouse will no longer control your Mac.
If this option is not selected (default setting), your keyboard and mouse control
your Mac.
You can manually toggle control back and forth between your Mac and the attached
external workstation by pressing ctrl+option+\.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
5.3
General
This tab controls how the MC Mix and application software work together.
45
Figure 5-4 General tab
5.3.1
General Preferences
Workstation tracks knob set changes
The workstation is aware of which knobset is selected and displays appropriate
controls.
Open plug-ins on workstation when editing
When a plug-in knobset is selected on the MC Mix, the workstation opens the
plug-in’s window.
Close plug-ins on workstation when editing
When a plug-in’s knobset is navigated from on the MC Mix, the workstation closes
the plug-in’s window.
Select by Touch
Touching an MC Mix fader selects that track in the application and attentions it
on the MC Mix. This is the same as pressing the fader SEL key.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Auto-bank to selected track
Selecting a track in the application causes the MC Mix to display the bank con-
taining that track. This keeps the selected track assigned to the surface.
Display track numbers on surface
The track number is included with the track name in the channel display.
5.3.2
Solo Mode Preferences
Solo in place
Mutes all tracks except solo track.
After-Fader Listen (AFL)
The Solo level is derived after fader level.
Pre-Fader Listen (PFL)
The Solo level is derived before fader level.
5.4
Preferences
46
Figure 5-5 Preferences tab
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
5.4.1
MC Mix display screen dim time
Drag the slider to set the amount of inactive time before the MC Mix display
screens dims to half intensity.
5.4.2
Footswitch
The footswitch punches in and out of recording. It is useful when recording and
getting ready to play an instrument.
Two types of footswitches can be attached to an MC Mix:
•
Momentary – There are two momentary types: normally open, push to close;
normally closed, push to open.
•
Toggle – Latches when pushed on; push again for off.
We recommend using one of the momentary types. The toggle type works, but
requires two presses. The MC Mix automatically distinguishes between momen-
tary types by checking whether the switch is open or closed upon power up.
Operation
47
This category selects what happens when the footswitch is pressed. Choose the
option that best suits your application.
Record | Record: Pressing the footswitch presses the RECORD button, which
punches in to record. Releasing the footswitch does nothing. Pressing the foot-
switch again also presses the RECORD button, which punches out.
Record | Play: Pressing the footswitch the first time presses the RECORD button,
which punches in. Releasing it does nothing. Pressing it a second time presses
the PLAY button, which punches out of recording and continues playback.
Status
This field cannot be set but shows the current status of the footswitch (on/off)
and its polarity.
5.4.3
MC Control Display
Drag the Brightness slider to adjust the MC Control Touchscreen display. Note
that this control is gray and inactive if an MC Control is not connected to your
instance of EuControl.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
5.5
Assign
Figure 5-6 Assign tab
48
This tab manages how tracks are assigned to the MC Mix’s strips. By default,
tracks are automatically assigned in banks of eight.
NOTE: When a project is reopened, the first eight tracks are assigned to the strips.
Click in the Assigned To column to pop up a menu with the following options:
•
auto assigned: Tracks are assigned automatically in response to the Bank
and Nudge buttons.
•
attentioned/selected track: This strip is assigned the attentioned track. A
track can be attentioned by selecting in the application or by pressing the
fader SEL key.
•
blank strip: This strip is kept blank and will not be included in NUDGE and
BANK operations until a Layout is recalled or it is explicitly reassigned. This
is useful when creating a Layout that does not require eight tracks.
In the popup menu, the current selection has a checkmark to its left.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
5.5.1
5.5.2
Display application’s track numbers
Select this checkbox to display the track number in addition to the name.
Clear All
Click Clear All to set all strips to being automatically assigned.
5.6
Layouts
49
Figure 5-7 Layouts tab
The tracks assigned to the MC Mix strips can be saved as a Layout. A Layout is
created from the current strip assignments and can receive a name. It can then
be recalled at a later time.
5.6.1
5.6.2
Recall
Highlight a name in the Name column and click Recall to recall that Layout.
Store
Click Store to store the MC Mix’s current track assignments as a new Layout.
Double-click the default name in the Name column to edit the name.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
5.6.3
5.6.4
Clear
Highlight a name in the Name column and click Clear to delete that Layout.
Clear All
Click Clear All to clear all Layouts. A dialog appears to confirm that you wish to
delete all existing Layouts.
50
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
Appendix A: Setting the IP Address
Most MC Mix users will never have to set a static Internet Protocol (IP) address
but in the rare cases that require it, the MC Mix does allow for it.
Normally the MC Mix uses Dynamic Host Configuration Protocol (DHCP) to obtain
its IP address, typically from a router. The MC Mix will revert to link-local addressing
to generate an IP address if a DHCP server is not found on the network, such as
when an MC Mix is connected directly to a computer with an Ethernet cable. Both
of these methods of obtaining IP addresses can be overridden by supplying a
static IP address, which the MC Mix uses in all cases when powered on.
CAUTION: Attempt this only if you have prior experience configuring a network.
To set a static IP address:
1. While holding down the PAGE W and PAGE X keys simultaneously, press
and release the POWER switch.
on the MC Mix.
51
Figure A-1 Use DHCP yes (left); Use DHCP no (right)
2. Turn the knob underneath the display clockwise to change the underlined
The Knob SEL and ON keys can be used instead of the knob to decrease or
increase the value, respectively.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
professional control surface
3. Press the PAGE X key to move the cursor to the next screen, in this case the
The Knob Top key can also be used to perform the same function as the
PAGE X key.
Press the PAGE W key to move the cursor back to the previous field or
screen to change a parameter to a different value.
Figure A-2 IP Address displays
4. Use the knob to set the first field of the IP Address.
right).
6. Use the knob to set the second field of the IP address.
52
7. Use the techniques described to set the remaining IP Address fields.
8. After setting the last IP Address field, press the PAGE X key to move the
Figure A-3 Subnet Mask display
9. Use the techniques described to set the Subnet Mask.
10. Press the PAGE W and PAGE X keys simultaneously to save this static IP
address. Power the MC Mix off and on to use the new IP address.
To cancel any changes made to the IP address at any time, power off the MC
Mix before pressing the PAGE W and PAGE X keys simultaneously.
Artist Series
Download from Www.Somanuals.com. All Manuals Search And Download.
|