El Paso Chile Company Stereo Amplifier OM163 User Manual

Manual

Series DMS

OM 163

Integrated Amplifiers

PROFESSIONAL AUDIO & SOUND

DIGITAL MUSIC SERIES

Installation Manual

and Operating Instructions

DIGITAL MUSIC SERIES

7 Channel - 3 Zone - Dual VOX -

Dual Mute - MOH - Vox Relay -

Module Port - Phone Interface

DMS 3040 - 40 Watt RMS

DMS 3080 - 80 Watt RMS

DMS 3120 - 120 Watt RMS

IMPORTANT NOTE: THIS OPERATING MANUAL IS PROVIDED AS AN INSTALLATION AND

AS AN OPERATING AID. PASO SOUND PRODUCTS, INC. DOES NOT ASSUME ANY

RESPONSIBILITY AS TO ITS ACCURACY AND SHALL NOT BE LIABLE IN TORT OR CON-

TRACT FOR ANY DIRECT CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING

FROM THE INSTALLATION, USE OR INABILITY TO USE THIS PRODUCT.

LISTED

COMMERCIAL

AUDIO

EQUIPMENT

30TJ

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK DO NOT EXPOSE THIS APPLIANCE TO

WATER, RAIN OR MOISTURE

CAUTION !

Innovation through technology since 1931

REV. 1.5

Specifications are subject to change without notice

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

IMPORTANT SAFETY INSTRUCTIONS

READ BEFORE OPERATING

BEFORE OPERATING THE AMPLIFIER, BE SURE YOU

FULLY UNDERSTAND ALL INSTRUCTIONS AND FEA-

TURES OF THE UNIT.

outlet, consult an electrician for replacement of the

obsolete outlet.

12) Use only the attachments and accessories speci-

fied in this manual.

13) If a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-

over.

14) Unplug this apparatus during lighting storms or

when unused for long periods of time.

1) Read these instructions carefully.

2) Keep these instructions.

3) Heed all Warnings.

4) Follow all instructions.

5) DO NOT use this apparatus near water.

6) Clean ONLY with a damp cloth.

15) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normal-

ly, or has been dropped.

16) DO NOT replace fuses unless power cord is

removed from the AC wall outlet.

17) DO NOT install accessories unless the power

cord is removed from the AC wall outlet.

7) DO NOT block any of the ventilation openings.

Install in accordance with the instructions provided.

8) DO NOT install near any heat sources such as

radiators, stoves, or other apparatus (including ampli-

fiers) that produce heat.

9) DO NOT mount amplifier into a container or a

closed unventilated closet while operating.

10) DO NOT place any object or accessory equipment

such as Tuners, Mixers, Cassette Decks, etc. on top of

the amplifier. Obstructing or closing the cabinet venti-

lation openings may cause overheating.

11) DO NOT defeat the safety purpose of the polar-

ized or grounding type plug. A polarized plug has two

blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The

wide blade and or the third prong is provided for your

safety. When the provided plug does not fit into your

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK DO NOT EXPOSE

THIS APPLIANCE TO WATER, RAIN OR

MOISTURE

RACK MOUNTING

A) Procure the optional accessory Rack Mount Kit Model 27/3501.

B) Turn amplifier up side down and remove the four rubber feet by unscrewing the four holding screws.

C) Remove two screws on each side of the amplifier holding the amplifier cover.

D) Install the rack kit brackets by using the self-tapping screws provided.

Fig. 3 - Rack Kit Mounting

OUTPUT LEVEL

DIGITAL MUSIC AMPLIFIER

DMS

PEAK

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO

SOUND

POWER

MODULE

-10

+10

-10

+10

INPUT 1

INPUT 2

INPUT 3

INPUT 4/AUX 1

INPUT 5/AUX 2

BASS

TREBLE

PAGE 3

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

PAGE 4

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

M U T E 1

M U T E 2

G R O U N D

U N M U T E

PAGE 5

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

FUNCTION SWITCHES AND JUMPERS LOCATION

S W 2 1 2

S W 2 1 7

( I N P U T 5 / A U X 2 )

S W 2 2 1

S W 2 2 2

PAGE 6

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

CAUTION !

REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD

ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET

THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE

PROVIDED FOR USE BY QUALIFIED PERSONNEL ONLY.

TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLATION OR SERVICING UNLESSYOU

ARE QUALIFIED TO DO SO. REFER INSTALLATION OR SERVICING TO QUALIFIED PERSONNEL.

FUNCTION SWITCHES AND JUMPERS DEFAULT SETTING TABLE

JUMPER AND

SWITCH ID NO.

JUMPER

REFERENCE

FUNCTION

DESCRIPTION

FACTORY

SETTING

FACTORY

SETTING

MAIN PCB JUMPERS

SW201

SW202

SW203

SW204

SW205

SW206

SW207

SW210

SW211

SW212

SW213

SW214

SW215

SW216

SW217

SW218

SW219

SW220

SW221

SW222

SW223

SW227

INPUT 1 -

INPUT 2 -

INPUT 3 -

INPUT 4 -

INPUT 1 (MIC 1) -

VOX RELAY -

INPUT 5 -

INPUT 2 -

INPUT 3 -

INPUT 4 -

INPUT 5 -

TEL IN -

INPUT 1 -

TEL IN -

INPUT 4/AUX 1 -

INPUT 3 -

INPUT 2 -

INPUT 1 -

PHANTOM POWER ON - OFF

UNMUTE ON - OFF

MUTE 1 - MUTE 2

PHANTOM POWER ON - OFF

VOX 1 - VOX 2 - OFF

OFF

VOX 1 - VOX 2 - OFF

MUTE 1 - MUTE 2 - OFF

VOX 1 - VOX 2 - OFF

MUTE 1 - MUTE 2 - OFF

MUTE 1 - MUTE 2

OFF

MODULE -

INPUT 5/AUX 2 -

CHIME TRIGGER -

SWITCHES

SW208

SW209

SW228

SW229

INPUT 5 -

MIC 5 OR AUX 2

SWITCH AUX 2

SWITCH AUX 1

SWITCH AUX 2

MODULE IN SOURCE - AUX 1 OR AUX 2

INPUT 4 -

INPUT 5 -

MIC 4 OR AUX 1

MIC 5 OR AUX 2

MOH BOARD JUMPERS

SW701

SW702

ZONE 2 INPUT SOURCE - AUX 1 - AUX 2 - MODULE

ZONE 1 INPUT SOURCE - AUX 1 - AUX 2 - MODULE

AUX 1

REAR PANEL SWITCHES

SW301

SW302

TONE BYPASS

EQ LINK

Defeats Front Panel Bass & Treble

Inserts External EQ between

SWITCH OFF

SWITCH OUT

Preamp out and Power Amp Input

PAGE 7

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

FUNCTION SWITCHES AND JUMPERS

UNDERSTANDING THE INPUT FUNCTIONS

SETTING THE VOX AND MUTE JUMPERS

DUAL VOX AND DUAL MUTE - The Amplifier provides two inde-

pendent VOX (V1 & V2) and two MUTE (M1 & M2) SYSTEMS

JUMPER SETTINGS - The VOX and MUTE Functions are

SWITCHED-ON or OFF by setting the JUMPERS on the VOX (A)

and MUTE (B) SOCKET. See Fig. 8A.

FUNCTION SOCKETS - EACH INPUT IS PROVIDED WITH A

VOX (V1 & V2) AND A MUTE (M1 & M2) SOCKET.

The SOCKETS are located on the Main PCB inside the Amplifier

as shown on the SWITCHES and JUMPERS LOCATION DIA-

GRAM in this Manual. Each Socket is identified by an ID NUMBER

and the FUNCTION and DEFAULT settings are listed on the

FUNCTION SWITCHES and JUMPERS DEFAULT SETTING

TABLE in this Manual.

INPUTS VOX AND MUTE FUNCTION - All Inputs including the

Module provide 2 - VOX SEND and 2 MUTE RECEIVE functions.

The VOX and MUTE functions are SWITCHED-ON, on each Input,

by Internal Jumpers provided for each Input. Two VOX BUSS

SEND (V1 & V2) and two MUTE BUSS RECEIVE (M1 & M2) can

be independently or simultaneously SWITCHED-ON to suit the

application requirement.

TO SET: Lift the Jumper and reset as required. making sure that

the JUMPER is properly positioned over the two shorting pins.

The VOX JUMPER has three positions:

The MUTE JUMPER has three positions:

OFF, V1 and V2

OFF, M1 and M2

TO VOX BUSS 1

VOX SEND

TO VOX BUSS 2

VOX JUMPERS

SOCKET

MUTE JUMPERS

SOCKET

SW220

JUMPER

SOCKET

ID NO.

SW215

JUMPER

SOURCE IN

AUDIO OUT

ANY

JUMPER

OFF

M 1

INPUT

V 1

V 2

M 2

Vox Mute Socket

FROM MUTE BUSS 1

FROM MUTE BUSS 2

MUTE RECEIVE

Fig. 8A - VOX and MUTE Sockets

DMS Anyinput

SETTING MORE THAN ONE FUNCTION

Fig. 8 - Any Input VOX and MUTE Functions

More than one JUMPER may be used on a VOX SOCKET as

shown below. In this example both the VOX 1 and VOX 2 functions

are SWITCHED -ON when the Input is activated. For this purpose

additional JUMPERS are packed with each Amplifier.

The figure below shows how the VOX 1 Logic Switch and the

MUTE 2 Logic Switch are SWITCHED-ON by moving the Jumpers

from the OFF position to the V 1 and M 2 position. When the Input

is activated by a Source signal the corresponding VOX Signal is

sent to the V1 BUSS.When the VOX 2 is activated by another Input

the MUTE Signal is present on the MUTE 2 BUSS and it will

MUTE this Input

OFF

VOX 1 BUSS ON

V 1 JUMPER

VOX SOCKET

OFF

JUMPER

V 2

VOX 2 BUSS ON

Vox Socket 01

JUMPER

VOX SEND

More than one JUMPER may be used on a MUTE SOCKET as

shown below. In this example both the MUTE 1 and MUTE 2 func-

tions will MUTE this INPUT when either VOX 1 or VOX 2 are acti-

vated by other INPUTS.

VOX 2 BUSS OFF

SW215

JUMPER

SOURCE IN

AUDIO OUT

ANY

OFF

INPUT

MUTE 1 BUSS ON

M 1 ^JUMPER

MUTE SOCKET

JUMPER

M 2

Mute Socket 01

SW220

MUTE 2 BUSS ON

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS ON

MUTE RECEIVE

NOTE: BE SURE NOT TO SET BOTH THE VOX AND CORRE-

SPONDING MUTE ON THE SAME INPUT OR THE INPUT WILL

MUTE ITSELF WHEN ACTIVATED.

JUMPER

DMS Anyinput 02

Fig. 8B - Any Input VOX 1 and MUTE 2 Activated

EXAMPLE: INPUT 1 - V 1 and M 1 BOTH ON.

PAGE 8

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

FUNCTION SETTINGS EXAMPLES

EXAMPLE 9

EXAMPLE 9A

VOX - MUTE JUMPERS SETTING

VOX 1 BUSS ON

OFF

VOX 1 BUSS ON

JUMPER

OFF

VOX SEND

MIC IN

JUMPER

VOX 2 BUSS OFF

SW215

VOX SEND

JUMPER

VOX 2 BUSS ON

SW215

JUMPER

MIC OUT

INPUT 1

MIC IN

MIC OUT

WHEN

ACTIVATED THE VOX

BUSS IS SWITCHED-ON

AND THE SIGNAL

PRESENT

MUTE

MIC

INPUT 1

SW220

JUMPER

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

THE

WHEN

MIC1

BUSS WILL

ACTIVATED THE VOX

BUSS AND THE VOX

MUTE INPUT 4/AUX 1

SW220

BUSS ARE SWITCHED-

ON AND THE SIGNALS

PRESENT ON THE

MUTE 1 & 2 BUSS WILL

MUTE THE TEL INPUT

AND INPUT 4/AUX 1

MUTE RECEIVE

JUMPER

OFF

MUTE 1 BUSS OFF

JUMPER

OFF

VOX 1 BUSS OFF

MUTE 2 BUSS OFF

VOX 1 BUSS ON

VOX SEND

MUTE RECEIVE

VOX 2 BUSS OFF

SW212

OFF

JUMPER

MUSIC

MUSIC OUT

VOX SEND

TEL IN

INPUT 4

AUX 1

VOX 2 BUSS OFF

SW214

WHEN MIC

THE VOX

IS ACTIVATED

BUSS IS

SWITCHED-ON AND THE

SIGNAL PRESENT ON THE

MUTE 1 BUSS WILL MUTE THE

MUSIC FROM INPUT 4/AUX 1

SW217

OFF

MUTE 1 BUSS ON

MUTE 2 BUSS OFF

PHONE OUT

JUMPER

TEL INPUT

Input 1-4 - V1 01

MUTE RECEIVE

WHEN

INPUT IS ACTIVATED

THE VOX BUSS IS

SWITCHED-ON AND

THE SIGNAL

PRESENT ON THE

MUTE BUSS WILL

MUTE INPUT 4/AUX 1

THE

TEL

SW216

EXAMPLE 9B

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS ON

VOX - MUTE JUMPERS SETTING

JUMPER

VOX 1 BUSS ON

OFF

JUMPER

MUTE RECEIVE

VOX 2 BUSS OFF

SW215

JUMPER

OFF

VOX 1 BUSS OFF

JUMPER

VOX SEND

MIC IN

MIC OUT

INPUT 1

VOX 2 BUSS OFF

SW212

WHEN

MIC

ACTIVATED THE VOX

BUSS AND THE VOX

BUSS ARE SWITCHED-

ON AND THE SIGNALS

PRESENT ON THE MUTE

SW220

MUSIC

JUMPER

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

MUSIC OUT

INPUT 4

AUX 1

BUSS WILL MUTE

THE INPUT 4/AUX

AND

INPUT 5/AUX 2

WHEN MIC1 OR TEL ARE

ACTIVATED THE VOX

OFF

VOX 1 BUSS OFF

BUSS IS SWITCHED-ON

AND THE SIGNAL PRESENT

ON THE MUTE 1 BUSS WILL

MUTE THE MUSIC FROM

INPUT 4/AUX 1

SW217

JUMPER

OFF

MUTE 1 BUSS ON

MUTE 2 BUSS OFF

VOX 2 BUSS ON

SW212

JUMPER

Input 1-4 -Tel - 01

JUKEBOX

MUTE RECEIVE

JUKEBOX OUT

INPUT 4

AUX 1

EXAMPLES

WHEN INPUT 4AUX

ACTIVATED THE VOX

SW217

BUSS IS SWITCHED-ON

AND THE SIGNAL PRESENT

ON THE MUTE 2 BUSS WILL

MUTE THE MUSIC FROM

INPUT 5/AUX 2

OFF

EXAMPLE 9 - INPUT 1 (MIC 1) mutes INPUT 4/AUX 1. When the

Microphone is activated the Music on AUX 1 is muted.

MUTE 1 BUSS ON

X ^JUMPER

EXAMPLE 9A - INPUT 1 (MIC 1) and TEL IN (Phone Paging) both

mute INPUT 4/AUX 1. When the Microphone or the Phone Paging

are activated the Music on AUX 1 is muted. The Microphone has pri-

ority over the Phone Paging.When MIC 1 is activated both the Phone

Paging and the Music on AUX 1 are muted.

JUMPER

MUTE-2

DELAY

3 to 30 Sec

OFF

VOX 1 BUSS OFF

VOX 2 BUSS OFF

SW213

MUTE 2 BUSS OFF

MUSIC

MUSIC OUT

INPUT 5

AUX 2

EXAMPLE 9B - INPUT 1 (MIC 1) mutes INPUT 4/AUX 1 and INPUT

5/AUX 2. INPUT 4 (Jukebox) mutes INPUT 5 (Sat. Rcvr). When the

Jukebox is turned-On the Background Music on AUX 2 is muted.

MUTE 2 DELAY (Reference 31) Control is provided.The Microphone

Paging has priority over the Background Music and the Jukebox.

INPUT 5/AUX

MUTED BY BOTH INPUT

4/AUX AND INPUT

SW223

WHEN ACTIVATED.

OFF

MUTE 1 BUSS ON

MUTE 2 BUSS ON

JUMPER

Input 1-4 -5 03

PAGE 9

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

CAUTION: TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER

ALL INPUT CONNECTIONS MUST BE MADE WITH THE AMPLIFIER POWER OFF.

INPUT 1 SETTING AS A MICROPHONE INPUT

MICROPHONE TYPE

PASO MICROPHONES

The Microphone Input accepts Low Impedance (250-600 ohm) All PASO low impedance Microphones have a balanced output for

Dynamic Microphones. The Microphone may be a balanced output best performance. Connect the RED lead to terminal HOT, the

type (three wire) or an unbalanced output type (two wire).

WHITE lead to terminal COM and the SHIELD to terminal G.

WIRING

THREE LEADS BALANCED MICROPHONE WIRING

INPUT 1 - Default Jumper Settings

MICROPHONE INPUT

Attach the microphone leads to the ter-

minal strip as per diagrams at left.

VOX - MUTE JUMPERS SETTING

SW215

The Diagram at Left shows the

Default Settings for INPUT 1.

VOX 1 is SWITCHED ON

VOX 2 is SWITCHED OFF

MUTE 1 is SWITCHED OFF

MUTE 2 is SWITCHED OFF

VOX 1 BUSS

ACTIVATED

OFF

JUMPER

VOX SEND

DO NOT GROUND THE MICROPHONE

CABLE SHIELD TO THE CHASSIS OF

THE AMPLIFIER

VOX 2 BUSS OFF

JUMPER

When the INPUT 1 (MIC 1) is

activated the VOX 1 BUSS is ON

and it will MUTE any Input with the

MUTE 1 Setting SWITCHED ON.

MIC IN

AUDIO OUT

BALANCED MICROPHONE

INPUT 1

IMPORTANT NOTE: The use of an

unbalanced Microphone (two leads) is

not recommended. For best results in a

250ohm 1.5mV

BALANCED

Input 1 - V1 - 01

SW220

INPUT 1 (MIC)

COM HOT

INPUT 3 (MIC)

G COM HOT

INPUT 2 (MIC)

COM HOT

JUMPER

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

Application

always

use

Low

MUTE RECEIVE

Unidirectional

Dynamic,

Impedance, Balanced Microphone

(three leads).

The microphone leads color refers to Paso Microphones only.

When using other brand refer to instructions packed with that

NOTE:To change the

INPUT Default Settings

refer to the appropriate

section in this Manual

unit.

SHIELD

UNBALANCED MICROPHONE

Attach the Microphone leads to the ter-

minal strip as per diagram in Fig 8A. The

cable length should not exceed: 15 Ft.

(4.5 m).

MIC

Lo Z

WHITE

RED

3120 Micbal 01

Fig. 10 - Balanced Microphone Input 1 Wiring

TWO LEADS UNBALANCED MICROPHONE WIRING

CABLE

CABLE LENGTH - If the distance

between the Microphone and the

Amplifier Input is greater than 15 ft (4.5

m) a Balanced Microphone must be

used. Use a two conductor shielded wire

and connect Microphone to Amplifier as

per Diagram in Fig. 10.

INPUT 1 - Default Jumper Settings

The Diagram at Left shows the

VOX - MUTE JUMPERS SETTING

SW215

VOX 1 BUSS

Default Settings for INPUT 1.

VOX 1 is SWITCHED ON

VOX 2 is SWITCHED OFF

MUTE 1 is SWITCHED OFF

MUTE 2 is SWITCHED OFF

OFF

ACTIVATED

JUMPER

VOX SEND

VOX 2 BUSS OFF

When the INPUT 1 (MIC 1) is

JUMPER

MICROPHONE CABLE ROUTING - The

Microphone Cable should be carefully

routed. Improper Cable routing will

cause spurious oscillations, regenerative

noises, hum, etc. that may permanently

damage the Amplifier.

activated the VOX 1 BUSS is ON

and it will MUTE any Input with the

MUTE 1 Setting SWITCHED ON.

MIC IN

AUDIO OUT

INPUT 1

250ohm 1.5mV

BALANCED

Input 1 - V1 - 01

INPUT 1 (MIC)

COM HOT

INPUT 3 (MIC)

G COM HOT

INPUT 2 (MIC)

COM HOT

SW220

JUMPER

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

Do not route cable next to power

lines.

Do not route cable near or over

Fluorescent Fixtures.

Do not route cable next to

Speaker Wires.

Do not install cable inside Power

Line Conduits.

Avoid the use of staples that may

penetrate the cable.

MUTE RECEIVE

NOTE:To change the

INPUT Default Settings

refer to the appropriate

section in this Manual

SHIELD

MIC

Lo Z

HOT LEAD

3120 Micunbal 01

Fig. 10A - Unbalanced Microphone Input 1 Wiring

PAGE 10

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

CAUTION: TO PREVENT POSSIBLE DAMAGE TO SPEAKERS

OR THE AMPLIFIER ALL INPUT CONNECTIONS MUST BE

MADE WITH THE AMPLIFIER POWER OFF.

INPUT 1 - USING A DESK BASE MICROPHONE

USING A PUSH-TO-TALK DESK BASE MICROPHONE

Microphone paging and precedence over AUX 1 or AUX 2 channels

may be accomplished by using a Desk Base or a Gooseneck

Microphone. Wire the Microphone output leads to the MIC input ter-

minals as per Fig. 11A.

WIRING

Wire the Desk Base Microphone leads to the Microphone

Input terminal strip as per diagram in Fig 11A. Check

Microphone instructions and connect HOT LEAD (B) to

Terminal HOT, COMMON LEAD (A) to Terminal COM and

SHIELD LEAD to Terminal G. Connect Muting Switch to

Terminals MUTE 1 or MUTE 2 and G as shown.

MUTING: The Amplifier is equipped with two independent Muting

Circuits:

Direct Muting by shorting the MUTE Terminals

Automatic Muting with VOX - Voice Activated Muting

For additional information on the Muting operation refer

to the Muting Functions section of this Manual.

DO NOT GROUND THE MICROPHONE CABLE SHIELD

TO THE CHASSIS OF THE AMPLIFIER

MUTING - PRIORITY SETTINGS

Direct Muting is provided by the Desk Base Muting Switch wired as

per diagram in Fig. 11A. If Auto-Mute (VOX) is desired follow instruc-

tions below. The Desk Base Muting Switch can be omitted.

Push to Tallk Key

MUTING INPUT 4/AUX 1 (MUSIC INPUT)

To mute Input 4/AUX 1 (Music Input) when Paging from MIC 1, set INPUT

4/AUX 1 MUTE 1 JUMPER to ON Position. Each time MIC 1 is activated

the Program on Input 4/AUX 1 is automatically muted by the VOX.

b50side

Fig. 11 - Desk Base Microphone

DESK BASE/GOOSENECK MICROPHONE WITH MUTING SWITCH

INPUT 1 - Default Jumper Settings

The Diagram at Left shows the

Default Settings for INPUT 1.

VOX 1 is SWITCHED ON

VOX 2 is SWITCHED OFF

MUTE 1 is SWITCHED OFF

MUTE 2 is SWITCHED OFF

VOX - MUTE JUMPERS SETTING

SW215

VOX 1 BUSS

ACTIVATED

OFF

JUMPER

VOX SEND

VOX 2 BUSS OFF

MASTER

REMOTE

VOLUME

When the INPUT 1 (MIC 1) is

JUMPER

activated the VOX 1 BUSS is ON

and it will MUTE any Input with the

MUTE 1 Setting SWITCHED ON.

MIC IN

M2 M1 RVC RVC

Push to Talk Key

AUDIO OUT

INPUT 1

250ohm 1.5mV

BALANCED

SW220

INPUT 1 (MIC)

INPUT 3 (MIC)

G COM HOT

INPUT 2 (MIC)

JUMPER

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

COM HOT

MUTE RECEIVE

MUTING SWITCH

Connect Desk Base or Gooseneck

Microphone as per diagram below.

Connect Muting Switch to MUTE 1

or MUTE 2 and G Terminals.

If using the VOX system the

muting switch is unnecessary.

NOTE:To change the

INPUT Default Settings

refer to the appropriate

section in this Manual

SHIELD

MIC

Lo Z

3120 Micbase 01

Fig. 11A - Input 1 and Muting Terminals

PAGE 11

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

CAUTION !

REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD

ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET

THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE

PROVIDED FOR USE BY QUALIFIED PERSONNEL ONLY.

TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLATION OR SERVICING UNLESSYOU

ARE QUALIFIED TO DO SO. REFER INSTALLATION OR SERVICING TO QUALIFIED PERSONNEL.

INPUT CONNECTIONS

CONDENSER AND ELECTRET MICROPHONES

PHANTOM POWER SELECTORS

PHANTOM POWER SELECTOR JUMPER

By following the Main Printed Board Layout locate the Selector

Jumpers with the ID No. as indicated on the Table below.

CONDENSER AND ELECTRET TYPE MICROPHONES

Condenser and Electret Microphones require a DC Operating

Voltage. The Amplifier provides this operating voltage or Phantom

Power selectively on Inputs.1-2-3-4-5.

Reset the Phantom Power Jumpers for INPUT 1 - 2 or 3 to the ON

position as desired. Lift the Mini Jumper out of the socket pins and

re-position to the ON position. Make sure the Jumper is lined up

with the socket pins.

Prior to selecting the Condenser or Electret Microphone be sure

that the Operating Voltage and Output Impedance of the device

match the Input characteristics of the Amplifier listed below.

INPUT 4 and 5 CONFIGURED AS MIC INPUTS

If INPUT 4 and INPUT5 need to be configured as Microphone

Inputs, reset the Phantom Power Jumpers as well as the

Switches provided for the two Inputs as indicated in the Table

below.

Phantom Power

Input Impedance

= 18 Volt DC

= 250 to 600 ohm

ACCESS TO PHANTOM POWER SELECTORS

1) Remove Power Cord from AC Outlet.

WIRING

2) Remove the three screws on each side of the Amplifier.

3) Lift Cover and carefully slide Cover out towards the rear.

4) Jumpers are located on the Main Printed Circuit Board.

CONDENSER/ELECTRET MICROPHONE

Carefully follow the wiring instruction packed with the Microphone

used. Attach the microphone leads to the terminal strip as per dia-

gram per Fig. below.

DO NOT GROUNDTHE MICROPHONE CABLE SHIELDTOTHE

CHASSIS OF THE AMPLIFIER

CONFIGURATION TABLES

BALANCED CONDENSER/ELECTRET MICROPHONE WIRING

INPUT 4 - 5 DEFAULT

SWITCH SETTINGS

MIC INPUTS PHANTOM POWER JUMPER SETTING

WHEN USING ELECTRET MICROPHONES

INPUT 4 - 5 SWITCH SETTINGS WHEN

CONFIGURING AS MICROPHONE INPUT

JUMPER

OFF

INPUT 1

INPUT 2

INPUT 3

Input

Switch No. Setting

Input

Switch No. Setting

SW201

JUMPER

INPUT 4 SW228

INPUT 5 SW208

INPUT 5 SW229

MIC 4

MIC 5

INPUT 4 SW228

INPUT 5 SW208

INPUT 5 SW229

AUX 1

AUX 2

SW202

JUMPER

250ohm 1.5mV

BALANCED

SW203

JUMPER

INPUT 1- 2 - 3 - 4 - 5 DEFAULT

JUMPER SETTINGS

INPUT 1 (MIC)

COM HOT

INPUT 3 (MIC)

INPUT 2 (MIC)

COM HOT

(When set as MIC 4)

(When set as MIC 5)

INPUT 4

INPUT 5

COM HOT

Input

INPUT 1 SW201

INPUT 2 SW202

INPUT 3 SW203

INPUT 4 SW204

INPUT 5 SW207

Jumper No. Setting

SW204

JUMPER

OFF

SW207

-0 +18V +18V

SHIELD

MIC

Lo Z

HOT LEAD

3120 Micbal Electret

Fig. 12 - Balanced Condenser/Electret Microphone Wiring - Configuration Tables

PAGE 12

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

PAGING FROM THE TELEPHONE SYSTEM

CAUTION: TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER ALL INPUT CONNECTIONS MUST BE MADE

WITH THE AMPLIFIER OFF (POWER OFF).

OUTPUT LEVEL

DMS

DIGITAL MUSIC AMPLIFIER

PEAK

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO

SOUND

TEL

POWER

MODULE

-10

+10

-10

+10

INPUT

INPUT 4/AUX

INPUT 5/AUX

BASS

TREBLE

DMS Amplifier

Telephone

KSU

Key Service Unit

telpagin

Fig. 13 - Connecting to the Telephone Paging KSU

WIRING - The Amplifier is interface ready for the Telephone OUTPUT LEVEL CONTROL - Use TEL OUTPUT LEVEL

line in applications requiring paging from the telephone sys- Control located on the Rear panel. After wiring adjust con-

tem. The Telephone line Paging Output (Tip and Ring) can trol for the desired output level.

be directly connected to the TEL input and to the HOT and

COM as shown in the wiring diagram Fig. 12A

VOICE ACTIVATED MUTING (VOX) - Muting of the AUX 1

channel (music muting) during Paging is automatic via the

Voice Activated Muting System. No contact closure for the

Muting Circuit is required from the Telephone system. For

CABLE - Use a two conductor twisted wire.

NOTE: The Telephone Paging Input is a Transformer additional information on the Muting operation refer to the

Balanced 600 ohm input. Muting Functions section of this Manual.

DO NOT GROUND THE TIP OR RING WIRE TO THE PHONE PAGING PRIORITY OVER MICROPHONES

CHASSIS OF THE AMPLIFIER Priority over any Microphone Input may be accomplished by

setting the MIC Inputs MUTE Jumpers.

TELEPHONE SYSTEM PAGING WIRING

BALANCED TELEPHONE PAGING WIRING

TEL INPUT - Default Jumper Settings

VOX - MUTE JUMPERS SETTING

The Diagram at Left shows the

Default Settings for TEL INPUT.

VOX 1 is SWITCHED ON

VOX 2 is SWITCHED OFF

MUTE 1 is SWITCHED OFF

MUTE 2 is SWITCHED OFF

SW214

VOX 1 BUSS

ACTIVATED

OFF

JUMPER

VOX SEND

TEL IN

VOX 2 BUSS OFF

JUMPER

When the TEL INPUT (PHONE) is

activated the VOX 1 BUSS is ON

and it will MUTE any Input with the

MUTE 1 Setting SWITCHED ON.

JUMPER

PAGING OUT

TEL INPUT

SW216

TEL

JUMPER

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

COM HOT

MUTE RECEIVE

600 ohm 100 mV

BALANCED

Telephone System

Paging Output

NOTE:To change the

INPUT Default Settings

refer to the appropriate

section in this Manual

RING

TIP

3120 Telpaging 01

Fig. 13A - Balanced Telephone Input Wiring

PAGE 13

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

SETTING INPUT 4 AS AUX 1

INPUT 4/AUX 1 DEFAULT SETTING

JUMPERS/SWITCH NO.

FACTORY SETTING

DEFAULT JUMPERS AND SWITCH SETTING

SW212 - VOX JUMPER

= OFF

= M 1

SW217 - MUTE JUMPER

SW228 - AUX1-MIC4 SWITCH

SW212 = OFF

JUMPER

OFF

VOX 1 BUSS OFF

= AUX 1

SW217 = M 1

SW228 = AUX 1

AUX 1

VOX 2 BUSS OFF

SW212

INPUT 4 SET AS AUX 1 (Reference. 19)

WHEN

ACTIVATED THE VOX 1

BUSS IS SWITCHED-ON

AND

PRESENT

MUTE

FROM INPUT 4/AUX 1

MIC

The AUX 1 input is provided for high level program source.

The output from a Satellite Receiver, Tuner, Tape Cassette

Deck, CD Player or other high level program source may

be directly connected to this input.

MUSIC

THE

SIGNAL

ON THE

MUSIC OUT

INPUT 4

AUX 1

BUSS WILL

THE

MUSIC

AUX 1 SENSITIVITY ATTENUATOR (Reference. 18)

The AUX 1 Input is equipped with a Sensitivity Attenuator

that allows the interface of the Input with Devices having a

wide range of Output Levels.

^{AUX 1}S^-W^MIC22⁴8^SWITCH

SW217

OFF

MUTE 1 BUSS ON

JUMPER

TYPICAL OUTPUT LEVEL OF MUSIC DEVICES:

AUX 1

MIC 4

Input 1-4 - V1 - 01

Satellite Receivers

Digital Tuners/Receivers

CD Players/Changers

Tape Decks

= 1 to 5 Volt

= 100 to 300 Mv

= 2 to 3 Volt

MUTE 2 BUSS OFF

= 500 to 700 Mv

SATELLITE RECEIVER

By adjusting the Input Sensitivity to the level that matches

the device used the correct interface with the Amplifier is

achieved resulting in lower overall distortion and better fre-

quency response characteristics.

paso

INPUT - 4 (AUX1)

47 kohm 100 mV

AM/FM TUNER

INPUT-5(AUX2)

47kohm 100mV

TRACK 0 1

AUX 1

ATTENUATOR

SETTING THE AUX 1 INPUT ATTENUATOR

Connect a Music Source to the Amplifier.

Turn Attenuator (rear panel) fully counterclockwise.

Turn INPUT 4 Front Panel Control to midway.

Switch Amplifier and Music Source ON.

Turn Attenuator Control (rear panel) until desired Output

Level is achieved.

(AUX2)

ATTENUATOR

CD PLAYER

INPUT 5

3120 Aux1 01

MIC-AUX2

BY INTERNAL

SWITCH

TAPE DECK

Adjust INPUT 4 Front Panel Level Control Up-Down as

desired.

MUSIC OUTPUT

STEREO SUMMING

Most Music Source Devices provide a Stereo Output.

Accordingly the Amplifier is equipped with two Jacks for the

AUX 1 Input (L and R). The two Inputs are internally

buffered and electronically mixed to Mono. This system

ensures that the Music Device is properly loaded and that

the Stereo Signals are correctly summed (L+R) to Mono

without distortion.

Fig. 14 - Rear Panel AUX 1 Input Diagram

CABLE

To connect the music source devices to the AUX 1 Input

use two single conductor shielded audio cable terminated

in a single prong phono plug on both ends.

INPUT - 4 (AUX1)

47 kohm 100 mV

AUX 1

ATTENUATOR

AUX 1 INPUT MUTING

MUTING - WHEN MIC 1 OR THE TEL IN ARE ACTI-

VATED THE VOX 1 BUSS IS SWITCHED-ON AND

THE SIGNAL PRESENT ON THE MUTE 1 BUSS

WILL MUTE THE MUSIC FROM AUX 1.

3120 Stereo Summ

Fig. 14A - Stereo Summing and AUX 1 Input Attenuator

PAGE 14

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

SETTING INPUT 5 AS AUX 2

INPUT 5/AUX 2 DEFAULT SETTING

JUMPERS/SWITCH NO.

FACTORY SETTING

DEFAULT JUMPERS AND SWITCH SETTING

SW213 - VOX JUMPER

= OFF

SW223 - MUTE JUMPER

SW208 - AUX 2-MIC 5 SWITCH

SW229 - AUX 2-MIC 5 SWITCH

= M 1

= AUX 2

SW213 = OFF

SW223 = M 1

SW208 = AUX 2

SW229 = AUX 2

JUMPER

OFF

VOX 1 BUSS OFF

VOX 2 BUSS OFF

AUX 2

SW213

INPUT 5 SET AS AUX 2 (Reference. 20)

WHEN

ACTIVATED THE VOX 1

BUSS IS SWITCHED-ON

AND

PRESENT

MIC

The AUX 2 input is provided for high level program source.

The output from a Jukebox, Tuner, Tape Cassette Deck,

CD Player or other high level program source may be

directly connected to this input.

MUSIC

THE

SIGNAL

ON THE

MUSIC OUT

INPUT 5

AUX 2

MUTE

BUSS WILL

THE

MUSIC

FROM INPUT 5/AUX 2

AUX 2 SENSITIVITY ATTENUATOR (Reference. 21)

The AUX 2 Input is equipped with a Sensitivity Attenuator

that allows the interface of the Input with Devices having a

wide range of Output Levels.

SW223

AUX 2 - MIC 5 SWITCH

OFF

SW208 and SW229

MUTE 1 BUSS ON

JUMPER

Input 1-4 - V1 - 01

TYPICAL OUTPUT LEVEL OF MUSIC DEVICES:

MUTE 2 BUSS OFF

Satellite Receivers

Digital Tuners/Receivers

CD Players/Changers

Tape Decks

= 1 to 5 Volt

= 100 to 300 Mv

= 2 to 3 Volt

AUX 2

MIC 5

SET TO AUX 2

= 500 to 700 Mv

SATELLITE RECEIVER

By adjusting the Input Sensitivity to the level that matches

the device used the correct interface with the Amplifier is

achieved resulting in lower overall distortion and better fre-

quency response characteristics.

paso

INPUT - 4 (AUX1)

47 kohm 100 mV

INPUT 5 (AUX 2)

47 Kohm 100 mV

AM/FM TUNER

TRACK 0 1

AUX 1

(AUX 2)

ATTENUATOR

SETTING THE AUX 2 INPUT ATTENUATOR

Connect a Music Source to the Amplifier.

Turn Attenuator (rear panel) fully counterclockwise.

Turn INPUT 5 Front Panel Control to midway.

Switch Amplifier and Music Source ON.

Turn Attenuator Control (rear panel) until desired Output

Level is achieved.

CD PLAYER

INPUT 5

MIC-AUX2

BY INTERNAL

SWITCH

TAPE DECK

3120 Aux2 01

Adjust INPUT 5 Front Panel Level Control Up-Down as

desired.

MUSIC OUTPUT

STEREO SUMMING

Most Music Source Devices provide a Stereo Output.

Accordingly the Amplifier is equipped with two Jacks for the

AUX 1 Input (L and R). The two Inputs are internally

buffered and electronically mixed to Mono. This system

ensures that the Music Device is properly loaded and that

the Stereo Signals are correctly summed (L+R) to Mono

without distortion.

Fig. 15 - Rear Panel AUX 2 Input Diagram

INPUT 5 (AUX 2)

47 Kohm 100 mV

CABLE

To connect the music source devices to the AUX 1 Input

use two single conductor shielded audio cable terminated

in a single prong phono plug on both ends.

(AUX 2)

ATTENUATOR

INPUT 5

AUX 2 INPUT MUTING

MIC-AUX2

MUTING - WHEN MIC 1 OR THE TEL IN ARE ACTI-

VATED THE VOX 1 BUSS IS SWITCHED-ON AND

THE SIGNAL PRESENT ON THE MUTE 1 BUSS

WILL MUTE THE MUSIC FROM AUX 2.

3120 Stereo Summ 01

Fig. 15A - Stereo Summing and AUX 2 Input Attenuator

PAGE 15

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

ADDRESSABLE DUAL VOX SYSTEM

VOX - VOICE ACTIVATED MUTING

VOX SENSITIVITY CONTROLS

DUAL VOX - VOICE ACTIVATED MUTING - The Amplifier

is equipped with a DUAL noiseless, fast acting Logic VOX

Switching System. When any of the INPUTS are activated

and a Signal is present on a given INPUT and either VOX 1

or VOX 2 or BOTH are Switched-ON (using internal

Jumpers) then the MUTE 1 or MUTE 2 BUSS or BOTH are

ACTIVE. If any of the INPUTS have the MUTE 1 or MUTE

2 Switched-ON (by Internal Jumpers) then the INPUT (or

INPUTS) will be MUTED according to the Jumpers Setting.

Once the SIGNAL-ON on the ACTIVE INPUT is terminated

the normal functions are automatically restored on all muted

inputs.

VOX-2

SENS

MUTE-2

DELAY

VOX-1

SENS

DMS3120 Vox Sens 01

Fig. 16 - Rear Panel VOX 1 and VOX 2 Sensitivity Control

and MUTE 2 Delay Control

VOX SENSITIVITY ADJUSTMENT

ACCESS TO VOX AND MUTE JUMPERS

REFER TO JUMPERS AND SWITCHES INTERNAL

ACCESS.

VOX SENSITIVITY ADJUSTMENT

1) Turn all Front Panel Input Level Controls to 0.

2) Turn VOX Sensitivity Control counterclockwise until it

stops.

3) Connect a Signal Source (Microphone, Telephone or

Music) to the respective Input Terminals (For connection

details refer to the appropriate section in this Manual).

4) While talking from a Paging Source (Microphone or

Telephone) or Playing Music rotate the INPUT LEVEL CON-

CAUTION: PRIOR TO PERFORMING THE ABOVE OPER-

ATION BE SURE TO FOLLOW THE SAFETY NOTES

REFERRING TO THE REMOVAL OF THE AMPLIFIER

COVER.

VOX SENSITIVITY CONTROLS

VOX 1 AND VOX 2 SENSITIVITY CONTROLS

The VOX 1 and VOX 2 Sensitivity Controls set the sensitiv- TROLS (Front Panel) until the desired output level is

ity level at which point the VOX 1 and VOX 2 are respective- achieved.

ly engaged during INPUT ACTIVATION.The VOX Sensitivity 5) While talking from a Paging Source (Microphone or

Controls are located on the Amplifier Rear Panel.

Telephone) or Playing Music, turn the Sensitivity Control

(VOX 1 or VOX 2) slowly clockwise until the Muting (MUTE

1 or MUTE 2) is activated.

VOX 1 SENSITIVITY CONTROL = Reference 33

VOX 2 SENSITIVITY CONTROL = Reference 32

VOX JUMPERS DEFAULT SETTING TABLE

JUMPER

ID NO.

JUMPER

REFERENCE

FUNCTION

DESCRIPTION

FACTORY

SETTING

FACTORY

SETTING

MAIN PCB JUMPERS

SW210

SW211

SW212

SW213

SW214

SW215

SW221

INPUT 2 -

INPUT 3 -

INPUT 4 -

INPUT 5 -

TEL IN -

VOX1 - VOX2 - OFF

OFF

INPUT 1 -

MODULE -

OFF

PAGE 16

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

ADDRESSABLE DUAL MUTING SYSTEM

DIRECT MUTING

DUAL MUTING SYSTEM - The Amplifier is equipped with a DUAL

noiseless, fast acting Logic MUTING Switching System. When any

of the INPUTS are activated and a Signal is present on a given

INPUT and either VOX 1 or VOX 2 or BOTH are Switched-ON

(using internal Jumpers) then the MUTE 1 or MUTE 2 BUSS or

BOTH are ACTIVE. If any of the INPUTS have the MUTE 1 or

MUTE 2 Switched-ON (by Internal Jumpers) then the INPUT (or

INPUTS) will be MUTED according to the Jumpers Setting. Once

the SIGNAL-ON on the ACTIVE INPUT is terminated the normal

functions are automatically restored on all muted inputs.

DIRECT MUTING - Direct Muting may be accomplished by short-

ing the MUTE 1 and MUTE 2 Terminals to the G Terminal through

an external switch. Each time the Muting Switch is closed the cor-

responding MUTE BUSS is activated.

WIRING

MASTER

REMOTE

VOLUME

MUTE-2

DELAY

M2 M1 RVC RVC

ACCESS TO MUTE JUMPERS

REFER TO JUMPERS AND SWITCHES INTERNAL ACCESS.

CAUTION: PRIOR TO PERFORMING THE ABOVE OPERATION

BE SURE TO FOLLOW THE SAFETY NOTES REFERRING TO

THE REMOVAL OF THE AMPLIFIER COVER.

MUTING TIMING - The MUTING is preset for -60 db Attenuation.

When MUTE 1 or 2 are activated the MUTE BUSS is instanta-

neously Switched-ON. When the Muting is deactivated the pro-

gram source is gradually restored.

MUTING SWITCH M 2

MUTING SWITCH M 1

3120 M1 - M2 01

Fig. 17 - Direct Muting Terminals and Diagram

MUTE 1 (M1) = TIMING PRESET 2-3 SECONDS

MUTE 2 (M2) = TIMING ADJUSTABLE 3-30 SECONDS

MUTE 2 DELAY = USE REAR PANEL CONTROL Reference 31

MUTE 2 DELAY - The M 2 Delay can be adjusted by using the

MUTE 2 DELAY CONTROL on the rear panel (reference 31).

Adjustable

from

3 to 30

seconds

MUTE 1

Terminals

shorted

MUTE 2

Terminals

shorted

Signal

Level

Signal

Level

Program

gradually

restored

Program

gradually

restored

2-3

sec.

Program

Attenuation

60 dB

Attenuation

60 dB

Mute terminals

opened

Mute terminals

opened

time

DMS mutfunct 01

DMS mutfunct 02

Fig. 17B - M 1 Function Timing Diagram

Fig. 17C - M 2 Function Timing Diagram

MUTE JUMPERS DEFAULT SETTING TABLE

JUMPER

ID NO.

JUMPER

REFERENCE

FUNCTION

DESCRIPTION

FACTORY

SETTING

FACTORY

SETTING

MAIN PCB JUMPERS

SW206

SW216

SW217

SW218

SW219

SW220

SW222

SW223

SW227

VOX RELAY -

TEL IN -

INPUT 4/AUX 1 -

INPUT 3 -

INPUT 2 -

INPUT 1 -

MODULE -

INPUT 5/AUX 2 -

CHIME TRIGGER -

MUTE 1 - MUTE 2

MUTE 1 - MUTE 2 - OFF

MUTE 1 - MUTE 2

OFF

PAGE 17

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

CAUTION !

REMOVAL OF THE AMPLIFIER COVER PRESENTS AN ELECTRICAL SHOCK HAZARD

ALWAYS REMOVE THE POWER CORD FROM THE AC WALL OUTLET

THE FOLLOWING INSTRUCTIONS REQUIRE THE REMOVAL OF THE AMPLIFIER PROTECTIVE COVER AND ARE PROVIDED

FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID THE RISK OF ELECTRICAL SHOCK DO NOT PERFORM ANY INSTALLA-

TION OR SERVICING UNLESS YOU ARE QUALIFIED TO DO SO.

INPUT 1 (MIC 1) UNMUTING FUNCTION

DIRECT UNMUTING

WIRING

MICROPHONE WITH UNMUTING ZONE SWITCH

Connect Paging Microphone

INPUT 1 (MIC 1) UNMUTING FUNCTION

as per diagram below

(reference 30). Connect Zone

Unmuting Switch to UNMUTE

(reference 9) and G Terminals.

The VOX (if ON) feature will

automatically mute the Music

The Input 1 (MIC 1) can be preset to be normally MUTED (INPUT

OFF) when the JUMPER SW205 - MIC 1 UNMUTE - IS SET TO

THE ON POSITION. The MIC 1 is SWITCHED-ON when the

UNMUTE and G Terminals are shorted by a Switch Contact

Closure. This function allows for a multi zone installation using two

or more Amplifiers and a single Microphone and Zone Switches.

When the Jumper SW205 is set to the ON Position the Microphone

Input is OFF and it is turned ON when the UNMUTE and the G ter-

minals are closed by a switch.

MASTER

REMOTE

VOLUME

MIC1

M2 M1 RVC RVC

250ohm 1.5mV

BALANCED

JUMPER NO.

SW205

FUNCTION

POSITION SET

INPUT 1 (MIC)

INPUT 2 (MIC)

COM HOT

MIC 1 Muted

If the Jumper requires resetting follow the instruction below.

ZONE UNMUTING SWITCH

ACCESS TO UNMUTING JUMPER

A = Common

B = Hot

MIC

Lo Z

SHIELD

1) Remove Power Cord from AC Outlet.

2) Remove the three screws on each side of the Amplifier

securing the Top Cover to the Chassis.

3120 Unmute 01

3) Lift Cover and carefully and slide Cover out towards the rear.

4) On the Main Amplifier Printed Board locate the SW205 -

MIC 1 UNMUTE Jumper Set.

Fig. 18 - Microphone and Zone Unmuting Diagram

5) Set Jumper to the ON position.

2 - ZONE

PAGING SELECTORS

UNMUTE - VOX AND MUTE JUMPER

SETTINGS ON AMPLIFIERS 1 & 2

INPUT 1

MIC 1

INPUT 4

AUX 1

MIC 1

UNMUTE

SPST ZONE

SWITCHES

OFF

ZONE 1

ZONE 2

JUMPER

OFF

JUMPER

SW205

SW215

SW217

TO AMP 1

TO AMP 2

3120 Unmute Jump Set

Fig. 18A - 2 - Zone System Jumper Settings

TO MIC INPUT

The Fig. at right shows a typical 2 Zone Switching

Panel. Use SPST Momentary Contact Switches. See

complete 2 - Zone Wiring Diagram provided in this

Manual.

3120 2 Zone Diagram 01

PAGING MICROPHONE

Fig. 18B - 2 - Zone Switching Panel

PAGE 18

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

Fig. 19 - 2 Zone Paging and Music System

2 ZONE PAGING AND MUSIC WIRING DIAGRAM

M U T E 1 O N

1 X O O N V

MUSIC SOURCE LINE

M U T E 1

M U T E 2

G R O U N D

M U T E 2

G R O U N D

U N M U T E

PAGE 19

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

EXTERNAL EQUALIZER LINK

SET EQ LINK SWITCH TO IN

^{SET TONE BY PASS SWITCH TO}ON

CONNECTING TO AN EXTERNAL EQUALIZER

The Amplifier is equipped with an External Equalizer Link

to allows the use of an External Equalizer for applications

requiring Frequency Selective Acoustic Correction. The

Amplifier is furnished with the two jacks of the Link bridged

by a SELECTOR SWITCH. When the EQ LINK Switch

(REFERENCE 12) is the IN position the internal

Preamplifier to Amplifier Link (Reference 13) is broken

allowing the insertion of an External Equalizer.

EXTERNAL EQUALIZER

paso

INSTALLATION TIPS

1) Use high quality, short length audio cables and position

PRE

OUT

the Equalizer in close proximity to the Amplifier. Avoid

mounting the EQ on top of the Amplifier unless is Rack

mounted.

2) Be sure that the Amplifier input controls and the EQ level

control are set at zero prior to turning the system On.

3) The Amplifier TONE BY PASS SWITCH (Reference 17)

should be set to ON ( linear response position).

4) Carefully adjust the EQ Level Control to avoid distortion

caused by excessive signal boost.

OFF

TONE

BYPASS

To Input of Equalizer

To Output of Equalizer

EQ LINK

OUT

POWER

3120 EQlink

EQ LINK

5) Follow the instructions supplied with the Equalizer.

WIRING

To connect to an External Equalizer use two (2) single con-

ductor shielded audio cables terminated in a single prong

phono plug on both ends.

Fig. 20 - Rear Panel External Equalizer Link Diagram

MIX BUSS BRIDGING

BRIDGING TWO AMPLIFIERS

The MIX BUSS (Reference 15)

allows two Amplifiers to be bridged

and share all inputs.

All signal sources connected to all

the inputs are common to the output

of both amplifiers. Muting and level

controls operate in exactly the same

way as if only one amplifier was

used.

AMPLIFIER A

AMPLIFIER B

MIX

BUSS

MIX

BUSS

WIRING

CABLE

To bridge two amplifiers or to con-

nect to an external Mixer use a sin-

gle conductor shielded audio cable

terminated in a single prong phono

plug on both ends.

LINE OUT

600

LINE OUT

600

3120 Mixbuss

Fig. 20B - Rear Panel Mix Buss Bridging Diagram

PAGE 20

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

MASTER REMOTE VOLUME

INPUT 4 (AUX 1) REMOTE VOLUME

MASTER

REMOTE

VOLUME

INPUT 4

REMOTE

VOLUME

RVC RVC

MASTER

INPUT 4 (AUX 1)

REMOTE VOLUME

CONTROL 10 K ohm

POTENTIOMETER

REMOTE VOLUME

CONTROL 10 K ohm

POTENTIOMETER

Paso Remote

Volume Control

RVC10W

3120 Remote Volume

Fig. 21 - Master Remote Volume Control Diagram

REMOTE VOLUME CONTROLS

Fig. 21B - Input 4 Remote Volume Control Diagram

The Amplifier features two independent Remote Volume Control Capability: The INPUT 4 (AUX 1) Remote Volume (Reference 26) and

the MASTER REMOTE VOLUME CONTROL (Reference 11). A 10 K ohm Potentiometer is required for either control. Mount the 10 K

Pot on a suitable Wall Plate or any other convenient surface and connect to the Amplifier RVC Terminals as shown in the Diagram. The

Paso Model RVC10W Decora Style Remote Volume Control may be used.

INPUT 4 (AUX 1) OPERATION

When connected the Remote Volume adjusts the INPUT 4 (AUX 1) Level only. Usually this input is utilized for the Music Source (Satellite

Receiver, CD Player, etc.).

MASTER VOLUME OPERATION

The Control is a Master Volume and controls all the Inputs of the Amplifier with the exception of the MOH and ZONE 1 and ZONE 2

Outputs.

CABLE

To connect the Remote Control to the Amplifier use a two conductor wire not less than AWG 24. While the Remote Volume System uses

DC rather than audio caution should be exercised in the layout of the wire. Always avoid routing next to power lines. If the total wire resist-

ance exceeds 3 K ohm the Volume may not go down to zero.

REMOTE VOLUME CONTROL - OPTIONAL ACCESSORY

MODEL RVC10W REMOTE VOLUME CONTROL

Remote Volume Control Potentiometer. Single

Gang Decora Style Plate.

SPECIFICATIONS

Control: 10 K ohm High Quality Control.

Connection: 6” Two Wire, color coded (Black and

Red) Pigtails stripped and tinned. Color Finish:

White. Dimensions: Front Plate = 4.5” High, 2.75”

Wide. Depth: 0.5”. Mounting Hardware: Supplied.

Fig. 21C - RVC10W Front View

Fig. 21D - RVC10W Rear View

PAGE 21

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

INSTALLING A MODULE

LISTED

INPUT-4(AUX1) INPUT-5(AUX2)

PRE

OUT

SUB OUT

PRE EQ

MIX

COMMERCIAL

AUDIO

BUSS

47kohm 100mV

EQUIPMENT

30TJ

RVC

(AUX1)

ATTENUATOR

(AUX2)

ATTENUATOR

EQ LINK

OUT

OFF

POWER SUB OUT LINE OUT

TONE

BYPASS

EQ LINK

INPUT 5

MIC-AUX 2

IN POST EQ 600

WARNING:THIS APPLIANCE

MUST BE EARTHED

BY INTERNAL

SWITCH

INPUT 4 AUX2

REMOTE 47Kohm 100 mV

INPUT 4 (MIC) VOLUME INPUT5 (MIC-AUX2)

TEL

INPUT 3 (MIC)

COM HOT

INPUT 2 (MIC)

TEL OUTPUT

LEVEL

COM HOT

COM HOT RVC RVC

COM HOT

250ohm 1.5mV

BALANCED

600 ohm 100mV

Insert into Module Connector

Connector

Top

Gold

Contact

PORT ACCEPTS

STANDARD

MODULE

Cable from

Amplifier

Printed Board

Copper Side

CAUTION: REMOVE

POWER CORD FROM

AC OUTLET PRIOR TO

INSTALLING MODULE

Side

View

Front

View

3120 Module Install

Module Bottom

Module Gold

Contacts

Fig. 22 - Rear Panel Module Installation Diagram

MODULE INSTALLATION

MODULE TYPE

The Amplifier accepts Audio Modules having a 6 Contact PCB Derivation. Module mounting panel should be 3” H., 1-3/8”

W. (78 X 35 mm).

INSTALLATION

CAUTION: REMOVE POWER CORD FROM AC OUTLET PRIOR TO INSTALLING A MODULE. BE SURE THAT THE

MODULE OUTPUT LEVEL CONTROL IS SET AT “0” PRIOR TO THE INSTALLATION.

1) Locate Rear Panel Module Port (Reference 22) and unscrew the two crosshead screws holding the cover and set aside.

2) Reach inside the Amplifier and gently pull-out the Module Blue Ribbon Connector. If the Connector is tied to the chas-

sis remove the Amplifier Top Cover and with a cutter cut the Nylon Tie holding the connector.

NOTE: BE CAREFUL NOT TO CUT THE CONNECTOR WIRE HARNESS.

3) Pull-out the blue-ribbon connector through the port opening (do not pull-out wire harness excessively).

4) By keeping the connector gold contacts on the left insert the Module PCB contacts into the socket.

5) Push Module through port opening and secure to rear panel by using the two screws removed with the Module cover.

PAGE 22

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

MODULE CONNECTOR DIAGRAM

MODULE CONNECTOR

Connector

Gold

Top

PCB

CONNECTOR

CN201

Contact

Connector Contacts

Cable from

Amplifier

6 = + 24V DC

5 = Module Input

4 = Module Output

3 = Ground

2 = Mute Buss 1

1 = Mute Buss 2

Side

View

MODULE

Front

View

3120 Module Schem

Fig. 23 - Module Connector Contacts Diagram

MODULE CONNECTOR DIAGRAM - The above Diagram indicates the function of each of the six contacts of the Module

Connector. The Module Blue Ribbon Connector is attached to a wire harness and left floating beyond the Module Port

Cover. The Wire Harness Amplifier End is attached to Connector No. CN201 and plugged into the mating connector on the

Main Printed Circuit Board.

MODULE DEFAULT SETTINGS

MODULE CONNECTOR

MODULE VOX - MUTE

Connector

Top

JUMPERS AND INPUT SOURCE

SWITCH DEFAULT SETTING

Gold

Contact

PCB

CONNECTOR

CN201

JUMPER

OFF

VOX SEND

VOX 1 BUSS OFF

Cable from

Amplifier

VOX 2 BUSS OFF

SW221

AUX 1 - AUX 2 SWITCH

SW209

AUX 1 SOURCE

MODULE OUTPUT

MODULE INPUT

AUX 1

AUX 2

AUX 2 SOURCE

Connector Contacts

6 = + 24V DC

5 = Module Input

4 = Module Output

3 = Ground

MODULE

JUMPER

OFF

MUTE 1 BUSS OFF

MUTE 2 BUSS OFF

Side

View

Front

View

SW222

2 = Mute Buss 1

1 = Mute Buss 2

3120 Module Functions

MUTE RECEIVE

Fig. 23A - Module VOX - MUTE - INPUT SOURCE Default Settings

MODULE FUNCTIONS - The Module Port accepts a stan- MUTE 1 - MUTE 2 RECEIVE or both.When a Signal is pres-

dard audio Module. When a Module is utilized several func- ent at the MUTE BUSS 1 or MUTE BUSS 2 the MODULE

tions can be activated by the Jumpers and Switch provided will be MUTED accordingly.

for this Input.

INPUT SOURCE - The SW209 Switch selectes the Input

VOX SEND - The SW221 Jumpers Set activates the VOX 1 Source for the Module either AUX 1 or AUX 2. The Signal

- VOX 2 SEND or both. When a Signal is present at the present at either Input will be sent to the MODULE INPUT

Module Output (Contact 4) then the VOX BUSS selected will (Contact 5).

be active.

By selecting the proper Setting several functions can be

MUTE RECEIVE - The SW222 Jumpers Set activates the derived from the Module.

PAGE 23

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

MOH - ZONE 1 INPUT SOURCE

DEFAULT JUMPER SETTING

CAUTION: TO REDUCE THE

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

ZONE 1

600

ZONE 2

ZONE 1

LEVEL

ZONE 2

LEVEL

SW702

MOH OUT

1 WATT 1 WATT

ZONE 2 INPUT SOURCE

DEFAULT JUMPER SETTING

BALANCED

PROFESSIONAL AUDIO

SOUND

CAUTION: TO REDUCE THE RISK OF FIRE OR

SHOCK DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE. DO NOT REMOVE COVER.

THERE ARE NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

DIGITAL MUSIC AMPLIFIER

POWER RATING

SUPPLY VOLTAGE

POWER CONSUMPTION

117V 500W MAX

UNSWITCHED

COM

25V 70V

GROUND

VOX-1

SENS

SPEAKER OUTPUT

LINE FUSE

5A 250V

117V 60HZ

CLASS 2 WIRING ACCEPTABLE

SER. NO.

SW701

DMS3120 MOH 01

Fig. 24 - Rear Panel View - ZONE 1 - ZONE 2 - MOH Outputs - Source Selectors and Controls

ZONE 1 MOH AND 8 OHM OUTPUTS

ZONE 1 OUTPUTS

The DMS Amplifier is equipped with two 1 Watt, 8 ohm Amplifiers

and a separate 600 ohm MUSIC ON HOLD AMPLIFIER.

MOH - ZONE1 & 2 AMPLIFIER FUNCTIONS

MOH AMPLIFIER

a) The MOH Amplifier can receive programs from AUX

1 - AUX 2 and the MODULE.

600 Ohm MOH - The MOH Output provides a 600 ohm, 1 Volt

Transformer Balanced Output (Reference 3).

b) Selection of the input source is by Internal Jumper.

c) The ZONE 1 independent 600 Ohm and 8 Ohm

Outputs may be used simultaneously.

1 WATT, 8 Ohm - Simultaneously a Second Zone 8 ohm, 1 Watt

Output may be utilized to drive up to 4 Speakers (Reference 4).

d) The MOH 600 ohm Output is Transformer Balanced.

e) The Rear Panel ZONE 1 Level Control operates both

the 600 Ohm and 8 Ohm Outputs simultaneously.

OUTPUT LEVEL CONTROL - A Level Control for both the 600

ohm Output and the 1 Watt Output is provided (Reference 2)

MOH AND 8 Ohm AMPLIFIER INPUT SOURCE SELECTION

The program source for the Input of the 600 ohm MOH Output and

the 8 ohm Output can be selected from either AUX 1 - AUX 2 or

the MODULE source. Set the Jumpers Set No. SW 702 to desired

position. Default setting is AUX 1.

MOH AND ZONE 1-2 OPERATION ISSUES

1) Paging from the Microphone Inputs or the Telephone

Input does not effect the MOH/ZONE 1-2 Amplifier.

2) Position of the INPUTS Level Control does not affect the

MOH/ZONE 1-2 Amplifier Output Level.

ZONE 2 OUTPUT

1 WATT, 8 Ohm - A Second Zone 8 ohm, 1 Watt Output may be

utilized to drive up to 4 Speakers (Reference 5).

3) Position of the AUX 1 and AUX 2 ATTENUATOR does not

affect the MOH/ZONE 1-2 Amplifier Output Level.

4) Muting activation of M1 or M2 Buss (from Microphones or

Telephone) does not effect the Output of the MOH/ZONE 1-

2 Amplifier except if the INPUT SOURCE is set to MODULE

and the Module Output is Muted. See Module Settings.

OUTPUT LEVEL CONTROL - A Level Control for the 1 Watt

Output is provided (Reference 6)

ZONE 2 - 8 Ohm AMPLIFIER INPUT SOURCE SELECTION

The program source for the Input the 8 ohm Output can be select-

ed from either AUX 1 - AUX 2 or the MODULE source. Set the

Jumpers Set No. SW 701 to desired position. Default setting is

AUX 1.

PAGE 24

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

MOH CONNECTIONS

600 ohm MOH System

MOH

Input

600

Ohm

Telephone

AWG 18 TWISTED PAIR

Telephone System

KSU

MOH - ZONE 1

INPUT SOURCE

DEFAULT JUMPER

SETTING

CAUTION: TO REDUCE THE

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

ZONE 1

600

ZONE 2

ZONE 1

LEVEL

ZONE 2

LEVEL

MOH OUT

1 WATT 1 WATT

BALANCED

PROFESSIONAL AUDIO

SOUND

DIGITAL MUSIC AMPLIFIER

POWER RATING

SUPPLY VOLTAGE

POWER CONSUMPTION

117V 500W MAX

UNSWITCHED

COM

25V 70V

GROUND

VOX-1

SENS

SW702

SPEAKER OUTPUT

LINE FUSE

5A 250V

117V 60HZ

CLASS 2 WIRING ACCEPTABLE

SER. NO.

3120 MOH Zone 1

MOH OTPUT LEVEL CONTROL

Fig. 25 - Rear Panel MOH Connection Diagram

MUSIC ON HOLD AMPLIFIER

MOH AMPLIFIER

LEVEL CONTROL

An independent 600 ohm, 1 Volt Output, Transformer Balanced

MUSIC-ON-HOLD Amplifier is provided. The Input SOURCE of the

MOH Amplifier can be selected from either the AUX 1 - AUX 2 or MOD-

ULE.

After the wiring is completed adjust the MOH/ZONE 1

Amplifier Level Control on the rear panel to the desired output

level (Reference 2).

MOH/ZONE 1 AMPLIFIER SOURCE SELECTOR

MOH - 600 OHM SYSTEM

MOH/ZONE 1 SOURCE SELECTOR

Most Phone systems operate on a 600 ohm Input Impedance, if the

Impedance required is 600 ohm connect the Amplifier to the Phone

System MOH by using the diagram above (Reference 3).

The Source for the MOH/ZONE 1 Amplifier can be selected

from either the AUX 1 - AUX 2 or MODULE by setting the

JUMPER SET No. SW702 provided for this purpose. Default

Setting for this Jumper Set is AUX 1. To change the setting do

the following:

MOH - 8 OHM, 1 WATT SYSTEM

Some older Key Phone systems require a 1 watt Power Output having

an Output Impedance of 8 ohm to drive the Music on Hold feature. If

the Impedance required is 8 ohm connect the Phone system MOH to

the 8 ohm, 1 Watt MOH Output of the Amplifier (Reference 4).

CABLE

Use a cable consisting of a twisted pair of at least AWG 18. Use care

in extending the cable and avoid routing near power lines, fluorescent

lights and other systems that may generate a disturbing electric field.

ACCESS TO THE MOH/ZONE 1 INPUT SOURCE SETTING

1) Remove Power Cord from AC Outlet.

2) Remove the three screws on each side of the amplifier

holding the amplifier cover.

3) Lift Cover and locate the Jumpers Set No SW702 on the

MOH Amplifier Board (see Function Switches Jumpers

Location Diagram).

SOURCE SELECTOR

4) Set Jumper as required (AUX 1 - AUX 2 or MODULE)

5) Replace protective cover.

Select the Input Source desired by following the instructions at right.

CAUTION: REMOVAL OF THE COVER PRESENTS AN ELECTRI-

CAL SHOCK HAZARD !

PAGE 25

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

USING SPEAKERS FOR ZONE 1 - ZONE 2

1/4W

4 Speaker System Max. Power Output= 1/4W Each

1/4W

AWG 18

TWISTED PAIR

AWG 18

TWISTED PAIR

OHM

ZONE 1

ZONE 2

Up to Four 8 ohm Speakers may

be Connected

Up to Four 8 ohm Speakers may

be Connected

OHM

1/4W

ZONE 2

INPUT SOURCE

DEFAULT JUMPER

SETTING

CAUTION: TO REDUCE THE

MOH - ZONE 1

INPUT SOURCE

DEFAULT JUMPER

SETTING

RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE

FUSE.

ZONE 1

600

ZONE 2

ZONE 1

LEVEL

ZONE 2

LEVEL

MOH OUT

1 WATT 1 WATT

BALANCED

PROFESSIONAL AUDIO

SOUND

DIGITAL MUSIC AMPLIFIER

POWER RATING

SUPPLY VOLTAGE

POWER CONSUMPTION

117V 500W MAX

UNSWITCHED

COM

25V 70V

GROUND

VOX-1

SENS

SW701

SPEAKER OUTPUT

LINE FUSE

5A 250V

117V 60HZ

SW702

CLASS 2 WIRING ACCEPTABLE

SER. NO.

3120 Zone 1&2

ZONE 1 OUTPUT LEVEL CONTROL

ZONE 2 OUTPUT LEVEL CONTROL

Fig. 26 - Rear Panel Zone 1 and 2 Speaker Connection Diagram

ZONE 1 AND 2 OPERATION

ZONE 1 AND 2 SETTINGS

ZONE 1 AND 2 OPERATION

INPUT SOURCE SELECTOR

The Amplifier is equipped with two independent 1 Watt, 8

ohm Outputs designated ZONE 1 (Reference 4) and ZONE

2 (Reference 5). The Outputs may be utilized to power up to

4 speakers in various combinations as described in the dia-

grams on the next page. This feature will provide a SEC-

OND and THIRD ZONE (in addition to the main output) with

up to 1 Watt of output power and will amplify only the

Source from either AUX 1 - AUX 2 or MODULE (see input

source selection) and will not be affected by the Paging

(from MIC or TEL), VOX or MUTING.

Independent JUMPER SETS for ZONE 1 (SW702) and

ZONE 2 (SW701) are available to select the Input Source

for the two 1 Watt Amplifiers.

DUAL PROGRAM SOURCE CAPABILITY

If desired separate program Sources may be used for

ZONE 1 and ZONE 2.

EXAMPLE: Use the program source from AUX 1 for ZONE

2 and the program source from AUX 2 for ZONE 2.

Select the Input Source desired by following the instructions

in the MOH Amplifier Source Selection section.

It can be used in any area (up to 1 Watt) where only a

Program Source is desired uninterrupted by Paging.

LEVEL CONTROL

CABLE

After the wiring is completed adjust the ZONE 1 (Reference

2) and ZONE 2 (Reference 6) Level Controls on the rear

panel to the desired output level.

Use an AWG 18 jacketed, twisted pair cable.

PAGE 26

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

ZONE 1 - ZONE 2 CONNECTING SPEAKERS

USING A SINGLE 8 OHM SPEAKER WIRING

Zone 1

8 Ohm

Zone 2

8 Ohm

Max. Power Output

1 Watt

USING A SINGLE 8 OHM SPEAKER PER ZONE

A single 8 ohm Speaker may be used connected to the

ZONE 1 and ZONE 2 1 Watt Output. In this configuration up

to 1 Watt of Power will be available on each Speaker.

ZONE 1

ZONE 2

ZONE 1

LEVEL

ZONE 2

LEVEL

600

Independent Level Controls are provided.

MOH OUT

1 WATT 1 WATT

BALANCED

3120 MOHspk01

Fig 27 - Using one 8 ohm Speaker

USING TWO 4 OR 8 OHM SPEAKERS WIRING

Zone 1

Zone 2

4 ohm

8 Ohm

½ W

¼ W

½ W

USING TWO 4 OR 8 OHM SPEAKERS

The Figure at left shows:

When using two

4 Ohm Speakers

the maximum

Output Power to

each Speaker is

½ Watt

When using two 8 Ohm

Speakers the maximum

Output Power to each

Speaker is ¼ Watt

ZONE 1 with two 4 ohm speakers connected in series, each

speaker provides ½ Watt power output (1 Watt Total).

ZONE 1

ZONE 2

ZONE 1

LEVEL

ZONE 2

LEVEL

ZONE 2 with two 8 ohm speakers connected in series, each

600

speaker provides ¼ Watt power output (½ Watt Total).

Independent Level Controls are provided.

MOH OUT

1 WATT 1 WATT

BALANCED

3120 Mohspk02

Fig 27A - Using two 4 or 8 ohm Speakers

USING FOUR 8 OHM SPEAKERS WIRING

Maximum Output

Power to each

Speaker is

¼ Watt

Zone 1

Zone 2

8 ohm 8 ohm

8 ohm

¼ W

USING FOUR 8 OHM SPEAKERS PER ZONE

Four 8 ohm Speakers are used and connected to the 1 Watt

Output. In this configuration up to 1/4 Watt of Power will be

available on each Speaker (1 Watt Total).

8 ohm

¼ W

ZONE 1

600

ZONE 2

Independent Level Controls are provided.

ZONE 1

LEVEL

ZONE 2

LEVEL

MOH OUT

1 WATT 1 WATT

BALANCED

3120 Mohspk03

Fig 27B - Using four 8 ohm Speakers

PAGE 27

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

REGULATED AUXILIARY POWER SUPPLY

24 VOLT POWER SUPPLY

POWER SUPPLY

The Amplifier provides a 24 Volt - 250 mA DC Regulated

Auxiliary Power Supply Output (Reference 8).

3120 Power Supply Output

CABLE

MASTER

24V DC

To connect the Power Supply Output to accessories use a

two conductor wire not less than AWG 18. This minimum

wire gauge is necessary to minimize potential Voltage

Drops in long wire connection applications. For wire resist-

ance refer to Table below.

REMOTE

VOX RELAY

NC NO

250 mA

VOLUME

MIC1

M2 M1 RVC RVC

Fig. 28 - 24 Volt Power Supply Output Diagram

WIRE GAUGE - RESISTANCE TABLE

NOTE:

WIRE

AWG

RESISTANCE IN

When calculating the Wire Resistance for each run

using a two conductor Wire the wire Resistance

should be doubled.

OHMS per 1000 Ft.

4.016

6.385

10.15

16.14

25.67

40.81

EXAMPLE: The Total Resistance of a 1000 Ft. run

of a AWG 24 two conductor Wire is:

25.67 X 2= 51.34 Ohm

VOX RELAY

VOX RELAY FUNCTIONS

VOX RELAY

VOX NOT ACTIVATED

MUTE 1 BUSS ON

VOX RELAY

Q237

RL201

The Amplifier provides a VOX RELAY (Reference 7) with a

single pole dual throw set of contacts. Figure A at left

shows the contacts when the Relay is not activated. Figure

B shows the contacts when the Relay is activated.

JUMPER

COM

D211

SW206

MUTE 2 BUSS OFF

SWITCHSET SW206 DEFAULT SETTING

The Relay can be configured to activate when either VOX

1 (M1) or VOX 2 (M2) or both (VOX 1 and VOX 2) are acti-

vated.

VOX RELAY

VOX ACTIVATED

Q237

MUTE 1 BUSS ON

RL201

JUMPER

COM

The VOX RELAY will remain engaged for as long as the

VOX is active.

D211

SW206

MUTE 2 BUSS OFF

SWITCHSET SW206 - The SW206 is defaulted to M1.

When VOX 1 is activated the Relay is switched ON. The

factory setting can be changed to set the Relay to activate

with either VOX 1 - VOX 2 or both.

MASTER

REMOTE

VOLUME

24V DC

250 mA

Both Jumpers (M1 - M2) may be installed.

VOX RELAY

NC NO

MIC1

M2 M1 RVC RVC

RELAY CONTACTS RATING

3120 Vox relay 01

7 AMPERE AT 30 VDC MAXIMUM RATING.

Fig. 28A - VOX Relay Output Terminals

PAGE 28

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DMS3040/3080/3120

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

INSTALLATION AND WIRING

INSTALLING AND USING A BOSE® EQUALIZER MODULE

CAUTION: PRIOR TO INSTALLING THE BOSE® MODULE IN THE AMPLIFIER FOLLOW THE INSTRUCTIONS SUPPLIED WITH

THE MODULE AND THEN READ THE INSTRUCTIONS IN THIS MANUAL’S “INSTALLING A MODULE” SECTION

METHOD 1

Connect to

Module

EQ OUT

Connect to INPUT 4/AUX 1

SET TONE BYPASS

SWITCH TO ON

METHOD 1

Equalize

EQUALIZING THE PROGRAM ONLY

BY USING THIS METHOD THE

MUSIC PROGRAM ONLY IS EQUAL-

IZED BY THE MODULE.

Music Only

LISTED

COMMERCIAL

AUDIO

INPUT-4(AUX1) INPUT-5(AUX2)

PRE

OUT

SUB OUT

PRE EQ

MIX

BUSS

47kohm 100mV

BE SURE THAT THE TONE BYPASS

SWITCH IS IN THE ON POSITION

EQUIPMENT

30TJ

(AUX1)

ATTENUATOR

(AUX2)

ATTENUATOR

OUT

AUDIO

EQ LINK

1) Connect the Output of the PRO-

GRAM SOURCE unit to the Module

IN Jack.

2) Connect the EQ. OUT Jack of the

Module to INPUT 4/AUX 1 of the

Amplifier.

OUT

OFF

INPUT 5

POWER SUB OUT LINE OUT

TONE

BYPASS

EQ LINK

IN POST EQ 600

MIC-AUX2

BY INTERNAL

SWITCH

WARNING:THIS APPLIANCE

MUST BE EARTHED

INPUT 4 AUX2

REMOTE 47Kohm 100 mV

INPUT 4 (MIC) VOLUME INPUT5 (MIC-AUX2)

TEL

INPUT 3 (MIC)

COM HOT

INPUT 2 (MIC)

TEL OUTPUT

LEVEL

COM HOT

COM HOT RVC RVC COM HOT

COM HOT

102 EQ. MODULE

LEVEL CONTROLS - Adjust INPUT

4/AUX 1 Front Panel Control to 1

o'clock. Turn Rear Panel ATTENUA-

TOR Control slowly clockwise until the

desired Output Level is achieved After

above adjustments are completed use

the INPUT 4/AUX 1 Front Panel

Control to increase or decrease the

Music Level as desired.

250ohm 1.5mV

BALANCED

600 ohm 100mV

MUSIC OUTPUT

BOSE MODULE METHOD 01

Connect Music

Source Output

to Module EQ IN

SATELLITE RECEIVER

TRACK 0 1

CD PLAYER

METHOD 2

Fig. 26 - Method 1 Module Wiring Diagram

USING THE EQ LINK

BY USING THIS METHOD ALL THE

AMPLIFIER INPUTS ARE EQUAL-

IZED BY THE MODULE.

BE SURE THAT THE TONE BYPASS

SWITCH IS IN THE ON POSITION

1) Connect the Output of the PRO-

GRAM SOURCE unit to the INPUT 4

(or INPUT 2) L and R Jacks.

2) Connect the EQ. OUT Jack of the

Module to the POWER IN Jack of the

Amplifier.

3) Connect the EQ. IN Jack of the

Module to the PREAMP. OUT Jack of

the Amplifier.

4) Set EQ LINK Switch on the

Amplifier to IN.

LEVEL CONTROLS - Adjust INPUT

4/AUX 1 Front Panel Control to 1

o'clock. Turn Rear Panel ATTENUA-

TOR Control slowly clockwise until the

desired Output Level is achieved After

above adjustments are completed use

the INPUT 4/AUX 1 Front Panel

Control to increase or decrease the

Music Level as desired.

Fig. 26B - Method 2 Module Wiring Diagram

BOSE® is a Registered Trademark of BOSE Corporation

PAGE 29

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

RESTAURANT/DINER WITH MUSIC AND JUKEBOX - APP. DATA 121

APPLICATION

This

Note

illustrates

typical

installation

Restaurant/Diner/Lounge using Background Music and a Jukebox.

The Background Music can be automatically interrupted when the

Jukebox is activated. The Background Music is then automatically

restored once the Jukebox stops playing.This built-in feature of the

DMS Amplifier eliminates the need of any external device.

PAGING MICROPHONE

PRIORITY PAGING MICROPHONE - A Low Impedance Dynamic

Microphone can be connected to the Amplifier INPUT 1. The

Microphone Input can be set to provide Priority Paging over both

the Music Program and the Jukebox if activated. Optionally Paging

may be generated from the Phone system if desired.

PAGING FROM THE PHONE SYSTEM

PRIORITY PAGING FROM THE PHONE SYSTEM - Paging may

be generated from a Phone System by using the TEL INPUT of the

Amplifier. The TEL INPUT can be set to provide Priority Paging

over both the Music Program and the Jukebox if activated.The TEL

INPUT provides a 600 ohm Transformer balanced Phone interface.

MUTE 2 DELAY

The Jukebox Configuration utilizes the VOX/MUTE 2 Buss. In order

to prevent the premature JUKEBOX/MUSIC SOURCE switching

(the Music Source cuts-in while the Jukebox is active) a MUTE 2

DELAY TRIMMER is available on the Rear panel to increase the

MUTE 2 DELAY as necessary. The MUTE 2 DELAY can be adjust-

ed from 3 to 30 Seconds.

EXAMPLE: If the Jukebox is playing and the Tune has a long pause

or the long pause while the Jukebox is cycling between CD’s it is

possible that the Music Source (Background Music) may cut-in

causing annoying and unwanted chatter while the Jukebox is still

active.To prevent this problem the MUTE 2 TIME DELAY should be

adjusted accordingly.

M U T E 1

M U T E 2

G R O U N D

JUKEBOX REMOTE VOLUME CONTROL

A Jukebox Remote Volume Control may be provided to adjust the

Output Level independently from the Background Music Source.

The Jukebox Music Level should be set in accordance to the ambi-

ent noise which may change during peak business hours.The AUX

1 Input (used for the Jukebox) is equipped with a Remote Volume

Control Feature. Use the optional PASO Model RVC10W (10K)

Volume Control mounted on a single gang plate.

U N M U T E

MUSIC ON HOLD

The Zone 1 Amplifier provides a separate 600 ohm Transformer

Balanced Music on Hold Output for the Telephone system. If the

Zone 1 Input Selector Switch is set to Input 3, the MOH Output

receives only the PROGRAM from the the MUSIC SOURCE with-

out Paging or the Jukebox interruptions.

2 X A U

1 X A U

J U M P E R

M O D

ZONE 1 & 2 ONE WATT - 8 OHM OUTPUT

The ZONE 1 and ZONE 2 Outputs may be used to cover small

area with MUSIC ONLY without interruption from the Microphone

or Phone Paging or the music from the Jukebox. The Program

Source for both 1 Watt Amplifiers may be independently selected

through Internal Jumpers (see Diagram). Output Level may be also

independently adjusted by the separate Level Controls.

ZONE 1 AND 2 SPEAKERS

The Wiring Diagram shows the connection of up to 4 (8 ohm)

Speakers for the Zone 1 & 2 - 1 Watt Amplifier. When 4 Speakers

are used each Speaker Output will be a 1/4 Watt.

2 X A U

R E P M U J U M P E R

1 X A U

M O D

INPUT JUMPERS - SWITCHES SETTING

The Diagram indicates the various Input Settings for this applica-

tion. Some settings may be already “Defaulted” when the Amplifier

is shipped and do not need re-setting.

K S U

l e e p T h o n e S y s t e m

PAGE 30

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

DMS3040/3080/3120

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

AUTO SERVICE STATION C - STORE - APP. DATA 123

APPLICATION

This Note illustrates a typical Auto Service Station

C-Store application. The size of the Service

Station and the number of Gas Pump Islands to

cover will determine the amount of outdoor

Waterproof Speakers required and the Power

Output of the Amplifier.

GAS PUMP OUTDOOR SPEAKERS

40 WATT SYSTEM EXAMPLE - The PASO Model

C55DMST Waterproof Music Speaker is recom-

mended.Typically each Speaker should be tapped

at 5 Watt. In this configuration up to 8 Speaker

may be used with the Model DMS3040 40 Watt

Amplifier for distribution of Music and Messages

at the Gas Pumps.

For larger systems use a higher power Amplifier

and the additional quantity of speakers required.

C _ STORE INDOOR SPEAKERS

The Amplifier is equipped with two independent 1

Watt , 8 ohm Amplifiers = ZONE 1 and ZONE 2.

C-STORE - Up to 4+4 Ceiling Speakers may be

utilized indoors in the Store area, Rest Rooms or

other area such as a separate concession. By uti-

lizing the separate (2) 1 Watt Amplifiers as a first

and second zone, only the Music program will be

distributed inside the Store. This avoids the con-

tinuous and annoying repeating of the messages

in the indoor areas. The output level may be

adjusted by the 1st and 2nd Zone Level Control.

ZONE 1 - ZONE 2 PROGRAM SOURCE SELEC-

TOR

M U T E 1

The program Source for each Zone Output may

be selected by setting the Zone 1 and 2 Jumper

Set to either AUX 1 - AUX 2 or Module Source.

M U T E 2

G R O U N D

U N M U T E

MUSIC ON HOLD

The Zone 1 Amplifier provides a separate 600

ohm Transformer Balanced Music on Hold Output

for the Telephone system. If the Zone 1 Input

Select Jumper Set is set to AUX 1, the MOH

Output receives the Music from the Satellite

Receiver without Paging or Messages interrup-

tions.

2 X A U

1 X A U

J U M P E R

PAGING MICROPHONE

PRIORITY PAGING MICROPHONE

Low

M O D

Impedance Dynamic Microphone can be connect-

ed to the Amplifier INPUT 1. The Microphone can

be set to provide Priority Paging over both the

Music Program and the Message Repeater.

Optionally Paging may be generated from the

Phone system if desired.The TEL INPUT provides

a 600 ohm Transformer balanced Phone interface.

MESSAGE REPEATER

The Message Repeater provides pre-recorded

Messages at the Gas Pumps Only. Each time a

message is initiated by the Repeater (AUX 1) the

Music (AUX 2) is automatically muted for the dura-

tion of the message.

REPEATER REMOTE VOLUME

A Master Remote Volume Control PASO Model

RVC10W may be provided to adjust the Output

Level of the Message Repeater in accordance to

the outdoors noise.

U A X 2

J U M P E R

K S U

U A X 1

M O D

e T l e p h o n e S y s t e m

PAGE 31

DMS3040/3080/3120

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Download from Www.Somanuals.com. All Manuals Search And Download.

DIGITAL MUSIC AMPLIFIERS

DIGITAL MUSIC SERIES

PROFESSIONAL AUDIO & SOUND

CUSTOMER SERVICE

REPAIR SERVICE

REPLACEMENT PARTS

REPAIR SERVICE

Please provide complete information when you request replace-

ment parts from either the Factory or a Paso Authorized

Distributor. Be certain to include the Part Number and

Description as it appears on the parts list, the Model Number of

the unit and if possible the Serial Number and the date of pur-

chase of the unit. Replacement parts inventory is maintained

specifically to repair Paso products. Part sales for other reasons

or applications will be declined.

Repair service for out of warranty Paso products may be

obtained form your local Paso distributor or any other qualified

repair station.

In warranty repairs must be returned to the Factory.

Prior authorization must be obtained from the Factory.

Products received without authorization will be refused by our

Receiving Dept..

ORDERING FROM THE FACTORY

Print all information on a purchase order form and mail to:

PASO SOUND PRODUCTS, INC.

4750 Goer Drive - Building F

IN WARRANTY REPAIR SERVICE

Call or write the Factory to obtain an authorization to return

the product for repairs.

CHARLESTON, SC 29406

Pack the equipment in the original carton or in a strong carton

with at least THREE INCHES of resilient packing material on all

sides, top and bottom. Seal the carton with reinforced tape and

mark it FRAGILE on at least two sides. Remember, the Carrier

will not accept liability for shipping damages if the unit is improp-

erly packed.

Be sure to include the following:

- Paso part number

- Part description

- Quantity required

- Model number of the unit

- Serial number of the unit

EQUIPMENT RECEIVED IN DAMAGED CONDITION DUE TO

POOR PACKING WILL BE REFUSED AND THE WARRANTY

COVERAGE IS AUTOMATICALLY VOIDED.

- Your payment or your authorization for COD shipment for parts

not covered by the Warranty or if your company has a current

account with the factory

The Paso Sound Limited Warranty provides:

RETAIN ORIGINAL IN WARRANTY PARTS UNTIL YOU

RECEIVE REPLACEMENTS. PARTS THAT SHOULD BE

RETURNED TO THE FACTORY WILL BE LISTED ON YOUR

PACKING SLIP.

The examination of the returned product must disclose in our

judgement, a manufacturing defect. The warranty does not

extend to any product that has been subject to misuse, neglect,

accident, improper installation or where the serial number of the

product has been removed or defaced.

For your convenience replacement parts are also available

through Paso Authorized Distributors and Dealers nation wide.

Obtain a location list directly from the Factory or your regional

Paso Representative.

Ship via insured prepaid United Parcel Service or Parcel Post to:

PASO SOUND PRODUCTS, INC.

4750 Goer Drive - Building F

CHARLESTON, SC 29406

Attn. SERVICE DEPARTMENT

The equipment will be returned freight prepaid after repairs.

TECHNICAL CONSULTATION

- Need help with your installation ?

- Need help with the operation of the unit ?

- Need help with a repair ?

Call or write for assistance. You will find our Technical Dept..

eager to help or assist you with any technical problem you may

have encountered except “`Customizing'' for a unique applica-

tion.

Be sure to include the following:

- Your name and address

- Date of purchase and copy of invoice

- A brief description of the difficulty

- A return address shipping label

The effectiveness of our consultation service depends on

the accuracy of the information you furnish.

Be sure to tell us:

- The Model and Serial number of the unit

- The date of purchase

OUT OF WARRANTY REPAIR SERVICE

Follow return instructions as per in warranty repair service. Prior

to performing all necessary repairs, you will be advised of the

charges and at that time a written authorization by you will be

required including authorization to return the equipment COD for

the service and shipping charges. This will avoid unnecessary

delays in returning the equipment to you.

- An exact description of the difficulty

- All you have done in attempting to correct the problem

Call our toll-free phone number:

1-800 231 3034

PAGE BACK

Printed in USA

Manual OM 163

Download from Www.Somanuals.com. All Manuals Search And Download.

Electro Voice Portable Speaker FR200B User Manual
Excalibur electronic Games A04 User Manual
Extron electronic Cable Box TP R AV User Manual
Extron electronic Network Card SCS 300 User Manual
Fisher Paykel Microwave Oven OB60SL11 User Manual
Ford Pasta Maker F 150 User Manual
Generac Portable Generator 00784 2 09290 4 User Manual
Generac Power Systems Portable Generator 04136 0 User Manual
GE Ventilation Hood JVB93 User Manual
Gitzo Medical Alarms PERS 2400 User Manual