Thank you very much for choosing an EIZO product.
Please read this User’s Manual carefully to familiarize you with safe and effective usage procedures.
Please retain this manual for future reference.
PRECAUTIONS
ꢀTo ensure personal safety and proper maintenance, please read this section.
CAUTION
Do not carry the monitor with the hood attached.
While carrying the monitor, the hood may fall or slip off, which may result in injury or equipment damage.
Do not place any objects on the hood.
If the hood falls or slips off or the monitor falls over, it may result in injury or equipment damage.
Attach only to specified EIZO LCD monitors.
Attach only to specified EIZO LCD monitors. Attaching to other monitors may cause the hood to drop, which may
Close the open/close cover until it contacts the stopper.
If the cover is not closed properly, the ventilation slots on the monitor will be covered and proper airflow will be
prevented. This may cause overheating inside the monitor and may result in fire, electric shock, or equipment
damage.
When attaching the hood to the 22.0-inch monitor with EZ-UP stand, do not attach the hood and i·Sound
(optional speaker) at the same time.
It may cause falling of the monitor, and may result in injury or equipment damage because the total weight exceeds
the supportable weight of the stand.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Assemble the left and right hoods.
NOTE
ꢀ
Assemble the hoods in the direction of the arrows marked on the insertions on the top covers of the right and left
hoods.
(1) Hold the left hood's left and top covers with the sides with the anti-reflective sheet facing inward.
(2) Connect the top and left covers by aligning the arrow (1 ) on the top cover's insertion with the two lines
on the left cover's insertion slot.
(3) Slide the top cover in the direction shown by the arrow (2 ).
Assembly of the left hood is complete.
(4) Assemble the right hood in the same way.
(3)
(1) (2)
Insertion
slot
Anti-reflective
sheet
Insertion
3. Attach the left and right hoods to the monitor.
NOTE
ꢀ
ꢀ
Be sure to install the second hood only after the other hood is firmly attached with hook.
When attaching the hood to the 22.0-inch monitor with EZ-UP stand, note the following points:
-
The height of the hood is about 16 mm longer than the one of 22-inch monitor, so that with tilting at the lowest
lifting position the hood may hit the desk on which the monitor is installed.
-
When attaching the hood and i·Sound (optional speaker) at the same time, the total weight exceeds the
supportable weight of the stand. Before attaching the hood, remove i·Sound from the monitor.
(1) Attach the top side of the left hood to the monitor first and then securely fit the left side of the hood in order
to fix the hood to the monitor.
(2) Insert the hook into the hole* on the hood (a) and slide it down along the projection on the back side of the monitor (b).
For 24.1” monitors
For 22.0” monitors
Insert into the hole
upper protection
Insert into the hole
under projection
Locations for hook
* The location for hook depends on the size of the monitor.
(3) Attach the right hood in the same way.
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach the left and right hoods to the monitor with the metal fitting.
(1) Check the locations of the depressions in the fitting.
(2) Insert the fitting into the left and right hoods by aligning those depressions with the projections (▲) in the
grooves on the right and left hoods.
For 24.1” monitors
For 22.0” monitors
5. Attach the open/close cover to the left hood.
NOTE
ꢀ
Do not attach the open/close cover to the right hood. Doing so prevents the cover from closing.
(1) Place the open/close cover on the top of the left hood (without contacting the metal fitting) from front (a) to
back (b).
(2) Slide the open/close cover to the right (c) until it contacts the stopper on the metal fitting.
4 holes of metal fitting and open/close cover come to the same position.
(2)
(1)
_____________________________________________________
Calibration
When performing calibration, slide the open/close cover to the left in order to attach the sensor.
NOTE
ꢀ
The open/close cover does not slide onto the right cover.
Sensor
Download from Www.Somanuals.com. All Manuals Search And Download.
__________________________________________________
Specifications
Dimensions
(W) × (H) × (D)
Weight
Attached to 22.0-inch monitor
513 mm (20.2) × 355 mm (14) × 229 mm (9) (inch)
571 mm (22.5) × 355 mm (14) × 229 mm (9) (inch)
Approx. 810g (1.79 lbs)
Attached to 24.1-inch monitor
Dimensions
Unit: mm (inch)
For 22.0-inch monitor
For 24.1-inch monitor
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|