MULTIMEDIA PROJECTOR
MODEL LC-W3
OWNER'S INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANCES
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: LC-W3
: Eiki
: EIKI International, Inc.
: 26794 Vista Terrace Drive, Lake Forest, CA, USA 92630-8113
Telephone No.
: 800-242-3454 (949-457-0200)
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
6
COMPUTER INPUT
24
SELECTING INPUT SOURCE
SELECTING COMPUTER SYSTEM
24
24
PREPARATION
7
PC ADJUSTMENT
26
26
27
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
NAME OF EACH PART OF PROJECTOR
7
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
POSITIONING PROJECTOR
8
PICTURE IMAGE SELECT
29
8
IMAGE LEVEL SELECT
29
9
PICTURE SCREEN ADJUSTMENT
30
30
ADJUSTABLE FEET
INSTALLING PROJECTOR IN PROPER POSITION
MOVING PROJECTOR
10
10
11
PICTURE SCREEN SELECT
VIDEO INPUT
31
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
31
32
CONNECTING PROJECTOR
12
PICTURE IMAGE SELECT
33
TERMINALS OF PROJECTOR
CONNECTING TO COMPUTER
CONNECTING TO VIDEO EQUIPMENT
12
13
14
IMAGE LEVEL SELECT
33
PICTURE SCREEN ADJUSTMENT
34
34
PICTURE SCREEN SELECT
PICTURE IMAGE
35
BEFORE OPERATION
15
PICTURE IMAGE ADJUSTMENTS
35
OPERATION OF REMOTE CONTROL
15
16
REMOTE CONTROL BATTERIES INSTALLATION
TOP CONTROLS AND INDICATORS
17
SETTING
38
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
18
18
18
19
SETTING MENU
38
APPENDIX
44
MAINTENANCE
44
44
45
45
46
47
BASIC OPERATION
20
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING PROJECTION LENS
LAMP REPLACEMENT
LAMP REPLACE COUNTER
TURNING ON / OFF PROJECTOR
TURNING ON THE PROJECTOR
20
20
21
TURNING OFF THE PROJECTOR
TROUBLESHOOTING
MENU TREE
48
50
52
53
55
56
57
58
58
59
ADJUSTING SCREEN
ZOOM ADJUSTMENT
22
22
22
22
22
23
23
23
FOCUS ADJUSTMENT
COMPATIBLE COMPUTER SPECIFICATIONS
INDICATORS AND PROJECTOR CONDITION
TECHNICAL SPECIFICATIONS
PJ LINK NOTICE
LENS SHIFT ADJUSTMENT
KEYSTONE ADJUSTMENT
PICTURE FREEZE FUNCTION
NO SHOW FUNCTION
SOUND ADJUSTMENT
CONFIGURATIONS OF TERMINALS
OPTIONAL PARTS
LENS REPLACEMENT
PIN CODE NUMBER MEMO
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
◆ Compact Design
◆ Keystone Correction
This projector is extremely compact in size and weight.
It is designed to carry and work anywhere you wish to
use.
Positioning of a projector may result in distorted image
being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
◆ Compatibility
◆ Power Management
This projector widely accepts various video and
computer input signals including;
Power Management function is provided to reduce power
consumption while a projector is not in use.
● Computers
This Power Management function operates to turn
Projection Lamp off when a projector detects signal
interruption and any button is not pressed. Projection
Lamp is automatically turned on again when a projector
detects signal or any operation button is pressed.
This projector is shipped with this function ON.
IBM-compatible or Macintosh computer up to 1600
x 1200 resolution.
● 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-
N color system can be connected.
● Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.
◆ Digital Visual Interface
This projector is equipped with DVI 24-pin terminal for
connecting DVI output from a computer.
● S-Video
◆ Color management
You can make fine adjustments to the colors on the
screen to change them to the desired colors.
At this time, the colors are changed within an extremely
narrow hue range, so that other colors are not affected.
The luminance and gamma values can also be changed
in addition to the hue.
This allows colors to be reproduced with great accuracy.
Faithful color reproduction and color correction which
effectively matches colors to scenes or emphasizes col-
ors can be achieved.
Adjustments can be made easily, because they are
reflected in the on-screen images in real time. Up to
eight colors can be adjusted at a single time. The adjust-
ment data can be saved for images in both in video
mode and PC mode (total 20 images). The adjusted data
is displayed in a list for easy checking.
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
◆ High Resolution Image
This projector provides 1366 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and UXGA
(1600 x 1200) is compressed into 1024 x 768 dots. This
projector cannot display image of over 1600 x 1200 dots.
When resolution of your computer is over than 1600 x
1200, reset a computer output for lower resolution.
◆ Multi-Scan System
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.
◆ Auto Picture Control
◆ One-Touch Auto PC Adjustment
The gamma value can be adjusted automatically in
accordance with the luminance of the screen. Images
that are either too dark or too bright can be adjusted to
the optimum level, so that these images can be repro-
duced without any distortion.
Equipped with an advanced Intelligent Digital Sharpness
Control which controls the sharpness automatically in
accordance with the images on the screen.
Incoming computer video signals are recognized and
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
◆ Motor-driven Lens Shift
Projection lens can be moved up and down with motor-
driven lens shift function. This function makes it easy to
provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.
◆ Multilanguage Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean or Japanese.
◆ Pj-to NetDirector (Optional)
◆ Digital Zoom (for Computer)
Digital Zoom function adjusts image size to approx. 1/4 ~
49 times of original image size, allowing you to focus on
crucial information at a presentation.
Pj-to NetDirector enables the projector to display the
image of the computer screen and the data image stored
in the computer via a network. The projector can be also
controlled and maintained through a web browser.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT OF CABINET
TOP CONTROLS
AND INDICATORS
INFRARED
REMOTE RECEIVER
PROJECTION LENS
AIR INTAKE
VENT
LENS CAP
SPEAKERS
BACK OF CABINET
EXHAUST VENT
TERMINALS
AND CONNECTORS
INFRARED
REMOTE RECEIVER
POWER CORD
CONNECTOR
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When
using or installing a projector, following
precautions should be taken.
● Do not put a flammable object near this vent.
● Keep rear grills at least 3.3’(1 m) away from
any object, especially heat-sensitive object.
● Do not touch this area, especially screws
and metallic parts. This area will become
hot while a projector is used.
CARRYING
HANDLE
This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.
LAMP COVER
When attached the Pj-to NetDirector (optional
part) to the projector, remove these parts.
Refer to the owner's manual in the optional
Pj-to NetDirector.
BOTTOM OF CABINET
AIR INTAKE VENTS
This projector is equipped with cooling fans for protection from
overheating. Pay attention to following to ensure proper
ventilation and avoid a possible risk of fire and malfunction.
● Do not cover vent slots.
● Keep side clear of any objects. Obstructions may block
cooling air.
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects correct input voltage. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of power supply being in use.
Connect a projector with a peripheral equipment before turning a
projector on. (Refer to pages 12 ~ 14 for connection.)
CAUTION
For safety, unplug AC Power Cord when an appliance is not
used.
Connect AC Power Cord (supplied) to a projector.
AC outlet must be near this equipment and must
be easily accessible.
When this projector is connected to outlet with AC Power Cord,
an appliance is in Stand-by Mode and consumes a little electric
power.
CAUTION
AC Power Cord must meet requirement of country where you use a projector.
Confirm AC plug type with chart below and proper AC power cord must be used.
If supplied AC Power Cord does not match AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For U.S.A. and Canada
For Continental Europe
Ground
To POWER CORD
CONNECTOR on a
projector.
To AC Outlet.
(120 V AC)
To AC Outlet.
(200 - 240 V AC)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
POSITIONING PROJECTOR
● This projector is designed to project on a flat
ROOM LIGHT
projection surface.
● Projector can be focused from 5.0’ (1.5m) ~ 52.2’
(15.9m).
Brightness in room has a great influence on
picture quality. It is recommended to limit
ambient lighting in order to provide best
image.
● Refer to figure below to adjust screen size.
52.2’(15.9m)
38.4’(11.7m)
400”
Max. Zoom
Min. Zoom
25.6’(7.8m)
300”
231”
12.7’(3.9m)
5.0’(1.5m)
308”
200”
154”
100”
40”
77”
30”
Max. Zoom
Min. Zoom
40”
30”
100”
77”
150”
115”
200”
250”
192”
300”
231”
400”
308”
Screen
Size
154”
5.0’ (1.5m)
12.7’ (3.9m)
19.1’ (5.8m)
25.6’ (7.8m)
32.0’ (9.8m) 38.4’ (11.7m) 52.2’ (15.9m)
Distance
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want. Refer to P 22 for operation.
Highest Lens Shift
Lowest Lens Shift
H3
H4
H1
H2
H1 : H2 = 6 : 1
H3 : H4 = 1 : 1
NOTE
Screen size and lens shift ratio on the above charts are standard values and they may change by positioning
conditions.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by
rotating ADJUSTABLE FEET. Projection angle can be
adjusted to 10.5 degrees.
Lift front of a projector and pull FEET LOCK LATCHES
on both sides of a projector.
1
Release FEET LOCK LATCHES to lock ADJUSTABLE
FEET and rotate ADJUSTABLE FEET to fine tune
position and tilt.
2
To shorten ADJUSTABLE FEET, lift front of a projector
and pull and undo FEET LOCK LATCHES.
3
Position and keystone distortion of image can be adjusted
using Menu Operation. (Refer to P 22 and 38.)
ADJUSTABLE FEET
FEET LOCK
LATCHES
INSTALLING PROJECTOR IN PROPER POSITION
Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard.
10˚
Do not tilt the projector more than 10 degrees above and below.
10˚
Do not point the projector up to project an image.
NO UPWARD
Do not point the projector down to project an image.
NO DOWNWARD
Do not put the projector on either side to project an image.
NO SIDEWAYS
10
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
MOVING PROJECTOR
Use Carrying Handle when moving a Projector.
When moving a projector, replace lens cover and retract
feet to prevent damage to lens and cabinet.
When this projector is not in use for an extended period,
put it into case (not supplied with this projector).
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
● Do not drop or bump a projector, otherwise damages or malfunctions may result.
● When carrying a projector, use a suitable carrying case.
● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer for best way.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on
pages 12 to 14 and connect properly.
INPUT TERMINAL (DIGITAL)
AUDIO INPUT 2 JACK
INPUT TERMINAL (ANALOG)
Connect computer output
(Digital DVI-D type) to this
terminal.
HD (HDCP Compatible) signal
can also be connected.
(Refer to P13 and 14.)
Connect computer output
(Analog HDB 15 pin type)
to this terminal.
Connect an audio output
(stereo) from computer to
this jack.
(Refer to P13.)
(Refer to P13.)
AUDIO INPUT 1 JACK
Connect an audio output
(stereo) from computer to
this jack.
(Refer to P13.)
R/C JACK
When using Wired/Wireless
Remote Control Unit as Wired
Remote Control, Connect
Wired Remote Control Unit to
this jack with Remote Control
Cable (not supplied).
INPUT 1
ANALOG
DIGITAL(DVI-D)
R/C JACK
CONTROL PORT
RESET
AUDIO 1
AUDIO 2
CONTROL PORT CONNECTOR
G
B
R
H/V
V
When controlling the projector
from a computer, connect the
computer to this connector
with a control cable. (Refer to
P13.)
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
RESET BUTTON
S–VIDEO
This projector uses a micro processor
to control this unit, and occasionally,
this micro processor may malfunction
and need to be reset. This can be
done by pressing RESET button with a
pen, which will shut down and restart
unit. Do not use RESET function
excessively.
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
(
)
MONO
INPUT 3
VIDEO INPUT JACKS
AUDIO INPUT JACKS
S-VIDEO INPUT JACK
Connect composite video Connect an audio output Connect S-VIDEO
output from video equipment from video equipment to output from video
5 BNC INPUT JACKS
to VIDEO/Y jack or connect these jacks.
component video outputs to (Refer to P14.)
VIDEO/Y, Cb/Pb and Cr/Pr
equipment to this
jack. (Refer to P14.)
Connect component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync and
Vert. Sync.)} from computer
to G, B, R, H/V and V jacks.
(Refer to P13 and 14.)
jacks. (Refer to P14.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection (✽ = Cable is not supplied with this projector.)
• VGA Cable (HDB 15 pin) ✽
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• BNC Cable ✽
• Control Cable for Serial Port
• Audio Cables (Mini Plug (stereo) ) ✽
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA/SXGA+/WXGA/UXGA)
Desktop type
Laptop type
Monitor Output
Monitor Output
Audio Output
Serial port
Monitor Output
Control Cable
for Serial Port
Audio
Cable ✽
(stereo)
DVI-Digital
Cable ✽
VGA Cable ✽
Terminal
BNC
Cable ✽
AUDIO IN 1 or 2
CONTROL
PORT
INPUT TERMINAL (DIGITAL)
INPUT TERMINAL (ANALOG)
INPUT 1
DIGITA(DVI-D)
ANALOG
R/C JACK
CONTROL PORT
RESET
AUDIO 1
AUDIO 2
5 BNC (G/B/R/HV/V)
G
B
R
H/V
V
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
(
)
MONO
Note:
INPUT 3
When connecting the cable, the power
cords of both the projector and the exter-
nal equipment should be disconnected
from AC outlet.
Terminals
of a Projector
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection (✽ = Cable is not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) ✽
• BNC Cable ✽
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽
• Audio Cable (RCA x 2) ✽
• S-VIDEO Cable ✽
• HDB 15 pin-SCART 21 pin Cable ✽
Video Source (example)
Video Cassette Recorder
Component video output equipment.
(such as DVD player or high-definition TV source.)
Video Disc Player
RGB Scart
21-pin Output Video Output
Composite
Digital Output
(HDCP compatible)
Component Video
Output
(Y, Cb/Pb, Cr/Pr)
Audio
Component Video Composite
S-VIDEO
Output
Output
Video Output
Output
(Y, Cb/Pb, Cr/Pr)
HDB 15 pin-
SCART 21 pin
Cable ✽
Video Cables
(RCA x 1 or
RCA x 3) ✽
DVI-Digital
Cable ✽
Audio Cable
(RCA x 2) ✽
S-VIDEO
Cable ✽
BNC Cable ✽
INPUT TERMINAL (ANALOG)
INPUT TERMINAL
(DIGITAL)
AUDIO IN
VIDEO
S-VIDEO
Y - Cb/Pb - Cr/Pr
Y - Cb/Pb - Cr/Pr
VIDEO
INPUT 1
ANALOG
DIGITL(DVI-D)
R/C JACK
CONTROL PORT
RESET
AUDIO 1
AUDIO 2
G
B
R
H/V
V
VIDEO/Y Cb/Pb
Cr/Pr
INPUT 2
S–VIDEO
VIDEO/Y Cb/Pb Cr/Pr
R–AUDIO–L
(
)
MONO
Note:
INPUT 3
When connecting the cable, the power cords
of both the projector and the external equip-
ment should be disconnected from AC outlet.
Terminals
of a Projector
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
AUTO PC ADJ. BUTTON
POWER ON-OFF BUTTON
Used to turn projector on or
off. (P20, 21)
LIGHT BUTTON
Lights the buttons on the remote
control for about 10 seconds.
Used to operate AUTO PC
Adjustment function. (P26)
COLOR M. BUTTON
Used to operate COLOR
MANAGEMENT.
(P35, 36)
MENU BUTTON
Used to select MENU
operation. (P18, 19)
ON-OFF
SELECT BUTTON
AUTO PC
-
LIGHT
MENU
I
Used to execute item
selected. It is also used to
expand / compress image
in DIGITAL ZOOM mode.
(P30)
AUTO
POINT (UP / DOWN / LEFT / RIGHT)
BUTTONS
COLOR M.
Used to select an item or adjust
value in ON-SCREEN MENU.
They are also used to pan image
in DIGITAL ZOOM +/– mode.
(P30)
POINT LEFT/RIGHT buttons are
also used as VOLUME +/–
buttons. (P23)
SELECT
IMAGE ADJ. BUTTON
Used to adjust image
level. (P35-37)
INPUT
IMAGE BUTTON
Used to select image
level. (P29, 33)
INPUT
IMAGE
INPUT BUTTON
Used to select input
source. (P24, 31)
SELECTION
NO SHOW BUTTON
Used to turn picture into
black image. (P23)
D.ZOOM
FREEZE
D.ZOOM BUTTON
NO SHOW
KEYSTONE
KEYS.
Used to select DIGITAL
ZOOM +/– mode and
resize image. (P30)
SCREEN
MUTE
FREEZE BUTTON
Used to freeze picture.
(P23)
L
LENS
F
Z
FOCUS
ZOOM
L
F
Z
SCREEN BUTTON
Used to select screen.
(P30, 34)
MUTE BUTTON
Used to mute sound. (P23)
KEYSTONE BUTTON
Used to correct
keystone distortion.
(P22, 38)
LENS SHIFT BUTTON
Used to select LENS
SHIFT function. (P22)
ZOOM BUTTON
Used to adjust zoom.
(P22)
WIRED REMOTE JACK
When using as Wired Remote
Control, connect Remote
Control Cable (not supplied).
to this jack.
Battery installation is required
when using as Wired Remote
Control.
FOCUS BUTTON
Used to adjust focus.
(P22)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
REMOTE CONTROL BATTERIES INSTALLATION
Remove battery
compartment lid.
Slide batteries into
compartment.
Replace compartment lid.
1
2
3
Two AA size batteries
Pull up lid and
remove it.
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
To insure safe operation, please observe following precautions :
● Use (2) AA or R06 type alkaline batteries.
● Replace two batteries at same time.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose Remote Control Unit to moisture, or heat.
● Do not drop Remote Control Unit.
● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
● Danger of explosion if battery is incorrectly replaced.
● Dispose of used batteries according to batteries manufacturers instructions and local rules.
Operating Range
Point Remote Control Unit toward
projector (Infrared Remote Receiver)
whenever pressing any button.
Maximum operating range for Remote
Control Unit is about 16.4’ (5m) and
60° in front and rear of a projector.
60°
16.4’
(5 m)
16.4’
(5 m)
60°
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
READY INDICATOR
LAMP INDICATOR
Turns to yellow when
life of projection lamp
draws to an end.
Flashes yellow when
the lamp cannot light
up. (P46, 53-54)
Flashes red when
Lights green when a
projector is ready to be
Becomes dim when a
projector is turned on.
And bright when a
projector is in stand-by
mode. (P20, 21, 53-54)
internal
projector
temperature is too
high. (P44, 53-54)
turned on.
And it
flashes green in Power
Management mode.
(P40, 44, 53-54)
POWER ON–OFF BUTTON
Used to turn a projector
on or off. (P20, 21)
MENU BUTTON
Used to open or close
MENU operation. (P18,
19)
INPUT BUTTON
Used to select input
source. (P24, P31)
ZOOM BUTTON
Used to adjust zoom.
(P22)
AUTO PC ADJ. BUTTON
Used to operate AUTO
PC Adjustment function.
(P26)
FOCUS BUTTON
Used to adjust focus.
(P22)
IMAGE BUTTON
Used to select image
level. (P29, 33)
LENS SHIFT BUTTON
Used to select LENS
SHIFT function. (P22)
SELECT BUTTON
Used to execute the
selected item.
POINT (VOLUME + / – ) BUTTONS
It is also used to
expand/compress image
in DIGITAL ZOOM mode.
(P30)
Used to select an item or adjust value
in ON-SCREEN MENU. They are also
used to pan image in DIGITAL ZOOM
+/– mode. (P30)
POINT LEFT/RIGHT buttons are also
used as VOLUME +/– buttons. (P23)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
REMOTE CONTROL UNIT
You can control and adjust this projector through ON-SCREEN
MENU. Refer to following pages to operate each adjustment on
ON-SCREEN MENU.
ON-OFF
1 DISPLAY MENU
Press MENU button to display ON-SCREEN MENU.
AUTO PC
AUTO
LIGHT
MENU
-
I
POINT BUTTONS
COLOR M.
Used to move a
Pointer UP/ DOWN/
RIGHT/ LEFT.
2 MOVING POINTER
Move pointer (✽ see below) or adjust value of item by pressing
POINT buttons on Top Control or on Remote Control Unit.
SELECT
✽ Pointer is icon on ON-SCREEN MENU to select item. See fig-
ures on section "FLOW OF ON-SCREEN MENU OPERATION"
below.
INPUT
MENU BUTTON
SELECT BUTTON
Used to select the item.
3 SELECT ITEM
Select item or set selected function by pressing SELECT button.
TOP CONTROL
POINT BUTTONS
Used to move a
Pointer UP/ DOWN/
RIGHT/ LEFT.
MENU BUTTON
SELECT BUTTON
Used to select item.
FLOW OF ON-SCREEN MENU OPERATION
MENU ICON
MENU BAR
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR). A red frame is POINTER.
Contrast
Auto
1
POINTER (red frame)
Press POINT UP/DOWN (red frame)
buttons to move POINTER.
POINTER
Select Menu to be adjusted
Move POINTER (red frame) to MENU ICON that you want to
2
select by pressing POINT RIGHT / LEFT buttons.
ITEM
Control or adjust item through ON-SCREEN MENU
Press POINT UP/DOWN buttons and move POINTER (red
frame or red arrow) to ITEM that you want to adjust, and then
press SELECT button to show ITEM DATA.
3
SELECT
BUTTON
Adjust ITEM DATA by pressing POINT RIGHT/LEFT buttons.
Refer to following pages for details of respective
adjustments.
4
ITEM DATA
Press POINT LEFT/RIGHT
buttons to adjust value or
set function.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press MENU BUTTON while connecting to PC input source.
SETTING MENU
SCREEN MENU
IMAGE SELECT MENU
Used to change
settings of projector
or reset Lamp
Replace Counter.
(Refer to P38-43)
Used to adjust size
of image. [Normal
/ Full / True / Digital
zoom +/–]
Used to select
PC SYSTEM MENU
GUIDE WINDOW
image level among
Standard, Real
and Image 1 ~ 10.
(Refer to P29)
Used to select
computer system.
(Refer to P24, 25)
Shows selected
item of ON-
SCREEN MENU.
(Refer to P30)
Input
SVGA1
PC ADJUST MENU
INPUT MENU
SOUND MENU
IMAGE ADJUST MENU
Used to adjust
parameters to
match with input
signal format.
Used to select
Used to adjust
volume or mute
sound.
Used to adjust computer
image.
[Contrast/Brightness/Color
/Tint/Color management
/Auto picture control
/Color temp.
input source (Input
1, Input 2 or Input
3). (Refer to P24)
(Refer to P23)
(Refer to P26-28)
/White balance (R/G/B)
/Sharpness/Gamma/Noise
reduction/Progressive]
(Refer to P35-37)
FOR VIDEO SOURCE
Press MENU BUTTON while connecting to VIDEO input source.
INPUT MENU
Used to select
input source
(Input 1, Input 2
or Input 3).
IMAGE SELECT MENU
SCREEN MENU
Used to select image
level among
Standard, Cinema
and Image 1 ~ 10.
(Refer to P33)
Used to adjust size of
image. [Full/ Normal/
Zoom / Natural wide]
(Refer to P34)
(Refer to P31)
Input
Auto
AV SYSTEM MENU
IMAGE ADJUST MENU
Same function as
Menu for PC source.
Same function as
Menu for PC source.
Used to select
system of selected
video source.
Used to adjust picture image.
[Contrast/Brightness/Color/Tint
/Color management
/Auto picture control/Color temp.
/White balance (R/G/B)
(Refer to P32)
/Sharpness/Gamma
/Noise reduction/Progressive]
(Refer to P35-37)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON THE PROJECTOR
Complete peripheral connections (with a computer, VCR,
etc.) before turning on the projector.
1
2
16
Connect the projector's AC power cord into an AC outlet.
The LAMP Indicator lights RED, and READY Indicator lights
GREEN.
Press the POWER ON-OFF button on the top control or on
the remote control to ON. The LAMP Indicator dims, and the
cooling fans start to operate. The preparation display
appears on the screen and the count down starts.
3
The preparation display disappears after 20 ~ 30 seconds.
Selected Input Source and Lamp control
After the count-down, the input source that was selected last
and the Lamp control status icon (see page 40) appear on
the screen.
Lamp control status
4
If the projector is locked with a PIN code, PIN code Input
Dialog Box will appear. Enter the PIN code as instructed
below.
PIN code Input Dialog Box
Enter a PIN code
Pointer
Select a number by pressing the POINT LEFT/RIGHT button and fix the
number with the SELECT button. The number will change to "✳". If you
fixed a wrong number, move the pointer to "Set" or "Clear" once by
pressing the POINT DOWN button, then return to "PIN code". Enter the
correct number again.
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, the pointer will automatically move to
"Set". Press the SELECT button so that you can start to operate the
projector.
If you entered a wrong PIN code, "PIN code" and the number (✳✳✳✳) will
turn red and disappear. Enter a correct PIN code all over again.
After the OK icon
disappears, you can
operate the projector.
What is PIN code?
PIN code is a security code using Personal Identification Number that
allows the person who knows it to operate the projector. Setting PIN code
prevents others except the specific users from operating the projector.
A PIN code consists of a four-digit number. Refer to PIN Code Lock
function in Setting on page 42 for locking operation of the projector with
your PIN code.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started. Set a new PIN code with special
care, write it down in column on page 59 of this
manual, and keep it at hand. Should the PIN code be
missing or forgotten, consult your dealer or service
center.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING OFF THE PROJECTOR
Press the POWER ON-OFF button on the top control or on
the remote control, and a message "Power off?" appears on
the screen.
1
2
Press the POWER ON-OFF button again to turn off the
projector. The LAMP Indicator lights bright and READY
Indicator turns off. After projector is turned off, Cooling Fans
operate (for 90 seconds). During this "Cooling Down" period,
this appliance cannot be turned on.
The message disappears after 4 seconds.
When the projector has cooled down, READY Indicator lights
GREEN again and you can turn projector on. After cooling
down completely, disconnect AC Power Cord.
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES
BEFORE TURNING IT OFF.
DO NOT DISCONNECT AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORE READY
INDICATOR LIGHTS GREEN AGAIN. OTHERWISE IT
WILL RESULT IN SHORTENING LAMP LIFE.
NOTE;
• The projector cannot be turned on during the cooling period with the
READY indicator turned off. You can turn it on again after the READY
indicator GREEN again.
• When the On start function is on, this projector is turned on automati-
cally by connecting the AC power cord to an AC outlet. (See page 40
for the On start function.)
• Do not operate the projector continuously without rest. Continuous use
may result in shortening the lamp life. Turn off the projector and give it
a rest about an hour in every 24 hours.
• This projector monitors internal temperature and automatically controls
the running speed of the cooling fans.
• If the WARNING TEMP indicator flashes red, see “WARNING TEMP
INDICATOR ” on page 44.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
Press ZOOM button on Top Control or ZOOM ▲/▼ button on
Remote Control Unit. Message “Zoom” is displayed.
1
2
Press ZOOM ▲ button or POINT UP button to make image
larger, and press ZOOM ▼ button or POINT DOWN button to
make image smaller.
Message disappears after 4 seconds.
FOCUS ADJUSTMENT
Press FOCUS button on Top Control or FOCUS ▲/▼ button on
Remote Control Unit. Message “Focus” is displayed.
1
2
Adjust focus of image by pressing FOCUS ▲/▼ button or
POINT UP/DOWN buttons.
NOTE;
Message disappears after 4 seconds.
Focus adjustment may not function properly if the image is
corrected by KEYSTONE adjustment.
LENS SHIFT ADJUSTMENT
Press LENS SHIFT button on Top Control or LENS SHIFT ▲/▼
button on Remote Control Unit. Message “Lens shift” is
displayed.
1
2
Press POINT UP button or LENS SHIFT ▲ button to move
image up, press POINT DOWN or LENS SHIFT ▼ button to
move image down.
Message disappears after 4 seconds.
KEYSTONE ADJUSTMENT
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING menu. (Refer to page 38.) Keystone
dialog box appears.
1
Correct keystone distortion by pressing POINT
UP/DOWN/LEFT/RIGHT buttons. Press POINT UP button to
reduce the upper part of the image, and press POINT DOWN
button to reduce the lower part. Press POINT LEFT button to
reduce the left part, and press POINT RIGHT button to reduce
the right part.
2
• Arrows are white in no correction.
• Arrow(s) of direction being corrected turn(s) red.
• Arrow(s) disappear(s) at the maximum
correction.
• If you press the KEYSTONE button on Remote
Control Unit once more while the keystone
dialog box is being displayed, the keystone
adjustment will be canceled.
Reduce the upper width
with POINT UP button.
Reduce the lower width
with POINT DOWN button.
Reduce the left part with
POINT LEFT button.
Reduce the right part with
POINT RIGHT button.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button.
NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out image.
To restore to normal, press NO SHOW button again or press any
other button.
Message disappears after 4 seconds.
SOUND ADJUSTMENT
Indicates roughly level of
volume.
DIRECT OPERATION
Volume
Press VOLUME (+/–) buttons on Top Control or on Remote Control
Unit to adjust volume. Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button to set
Mute function On or Off.
Press MUTE button on Remote Control Unit to cut off sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) buttons.
Display disappears after 4 seconds.
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
SOUND MENU
1
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon.
Press POINT UP/DOWN buttons to move a red frame pointer to
item that you want to select, and then press SELECT button.
SOUND Menu icon
Indicates roughly
2
level of volume.
Volume
Close SOUND Menu
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing.
Mute
Press POINT LEFT/RIGHT buttons to cut off sound. Dialog box
display is changed to “On” and sound is cut off. To restore sound to
its previous level, press POINT LEFT/RIGHT buttons again.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
SELECTING INPUT SOURCE
DIRECT OPERATION
INPUT button
Input 1
Select INPUT source by pressing INPUT button on Top Control or on
Remote Control Unit.
Select INPUT source by pressing INPUT 1, INPUT 2 or INPUT 3
button on Remote Control Unit.
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
Input 2
Input 3
SELECTING COMPUTER SYSTEM
WHEN SELECT INPUT 1 (COMPUTER INPUT TERMINALS )
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
INPUT Menu icon.
1
2
3
Input
SVGA1
Press POINT UP/DOWN buttons to move a red arrow pointer to
Input 1 and then press SELECT button. Source Select Menu will
appear.
Input 1
INPUT Menu icon
Input 2
Input 3
Move a pointer (red arrow) to
Input 1 and press SELECT
button.
Move a pointer to source that you want to select and then press
SELECT button.
Input 1
RGB (PC analog)
Source Select Menu
When your computer is connected to INPUT 1 (ANALOG)
terminal, select RGB (PC analog).
Move a pointer (red arrow)
to source and press
SELECT button.
RGB (Scart)
When scart video equipment is connected to INPUT 1
(ANALOG) terminal, select RGB (Scart).
RGB (PC digital)
NOTE;
When your computer is connected to INPUT 1 (DIGITAL)
terminal, select RGB (PC digital).
HDCP (High-bandwidth Digital Content
Protection) is a system for protecting digital
entertainment content which is delivered by DVI
(Digital Visual Interface) from being copied.
The specification of HDCP is decided and
controlled by Digital Content Protection, LLC.
Should the specification be changed, this
projector may not display the digital content
protected by HDCP.
RGB (AV HDCP)
If a HDCP-compatible signal source is connected to the INPUT 1
(DIGITAL) terminal, select RGB (AV HDCP).
NOTE;
INPUT SOURCE changes if the INPUT 1 button on Remote Control
Unit is pressed.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connect a computer output [5 BNC Type (Green, Blue, Red,
Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V
jacks.
INPUT MENU
Input
SVGA1
Input 1
Input 2
Input 3
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
INPUT Menu icon.
1
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
Press POINT UP/DOWN buttons to move a red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
2
Input 2
Move a pointer (red arrow) to RGB and then press SELECT
button.
3
Source Select Menu
Move a pointer (red arrow)
to RGB and press SELECT
button.
NOTE;
INPUT SOURCE changes if the INPUT 2 button on Remote Control
Unit is pressed.
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA, SXGA+, WXGA
or UXGA (refer to “COMPATIBLE COMPUTER SPECIFICATION” on pages 52-53). When a computer is selected, this
projector automatically tunes to incoming signal and projects the proper image without any special setting. (Some
computers need to be set manually.)
The projector displays one of the Auto, -----, Mode 1/2/3/4/5/6/7/8/9/10, or the system provided in the projector.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon.
PC SYSTEM MENU
Auto
Mode 1
System
When image is not provided properly, manual adjustment
is required. (Refer to P27 and 28.)
PC SYSTEM Menu icon
Displays system being
selected.
There is no signal input from computer. Make sure
connection of computer and a projector is set correctly.
(Refer to TROUBLESHOOTING on page 48.)
––––
User preset adjustment in MANUAL PC ADJUSTMENT.
Adjustment data can be stored in the Mode 1-10.
Mode 1
SVGA 1
Computer systems provided in the projector. The
projector chooses proper system and displays it.
✽
Mode 1 and SVGA 1 are examples.
PC SYSTEM MENU
SELECT COMPUTER SYSTEM MANUALLY
Mode 1
System
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
Mode 1
PC SYSTEM Menu icon
Displays system being selected.
Mode 2
SVGA 1
SVGA 2
Press MENU button and ON-SCREEN MENU will appear. Press
1
Systems on this dialog box can
be selected.
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM Menu icon.
SVGA 3
Custom Mode (1~10) set in PC
ADJUST Menu. (P27, 28)
Press POINT UP/DOWN buttons to move a red arrow pointer to
2
system that you want to set, and then press
SELECT button.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
ADJUST Menu icon.
PC ADJUST MENU
1
2
Auto PC adj.
SVGA1
Press POINT UP/DOWN buttons to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Top Control or on Remote Control
Unit.
PC ADJUST Menu icon
Move a red frame pointer to AUTO
PC Adj. icon and press SELECT
button.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P25). Refer to
MANUAL PC ADJUSTMENT section (P27-28).
NOTE
● Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment
function. When image is not provided properly through this function, manual adjustments are required. (Refer to pages
27, 28.)
● Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “480p”, “575p”, “480i”, “575i”
“720p (HDTV)”, “1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed. However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 10 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal is selected on INPUT MENU
(P24).
PC ADJUST MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
ADJUST Menu icon.
1
Auto PC adj.
SVGA1
PC ADJUST Menu icon
Press POINT UP/DOWN buttons to move a red frame pointer to
item that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press POINT LEFT/RIGHT
buttons to adjust value.
2
Move a red frame pointer to item
and press SELECT button.
Fine sync
Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT buttons to adjust value. (From 0 to 31.)
Total dots
Shows status
(Stored / Free) of
selected Mode.
Adjust the number of total dots in one horizontal period. Press
POINT LEFT/RIGHT buttons and adjust number to match your PC
image.
Fine sync
Mode 1
Stored
Position H
Selected Mode
Adjusts horizontal picture position. Press POINT LEFT/RIGHT
buttons to adjust position.
Press POINT LEFT/RIGHT
buttons to adjust value.
Position V
Press SELECT button at this icon to
adjust “Clamp,” “Display area H” or
set “Display area V.”
Adjusts vertical picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Current mode
Press SELECT button to show information of computer selected.
Clamp
Adjusts clamp position. When image has a dark bar(s), try this
adjustment.
Current mode
Display area H
Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT buttons to decrease/increase value and then
press SELECT button.
Press SELECT button at
Current mode icon to
show information of
computer connected.
Display area V
Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT buttons to decrease/increase value and then
press SELECT button.
Press SELECT button at this icon
to display previous items.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
Other icons operates as follows.
To store adjustment data.
Reset
This Mode has parameters being stored.
Reset all adjust parameters on adjustment dialog box to previous
figure.
Mode free
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Stored
Free
Free
Free
Free
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button. Move
a red arrow pointer to Mode that you want to clear and then
press SELECT button.
Store
To store adjustment parameters, move a red frame pointer to
Store icon and then press SELECT button. Move a red arrow
pointer to any of Mode 1 to 10 that you want to store and then
press SELECT button.
Close this dialog box.
Vacant Mode
Shows values of “Total dots,”
Quit
“Position H,” “Position V,”
“Display area H,” and “Display
area V.”
Closes PC ADJUST MENU.
To clear adjustment data.
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Stored
Free
Free
Free
Free
Close this dialog box.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE IMAGE SELECT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1 to Image 10 by
IMAGE button
pressing IMAGE button on Top Control or IMAGE SELECTION ▲/▼
button on Remote Control Unit.
Standard
Real
Standard
Normal picture level preset on this projector.
Image 1
Real
Picture level with improved halftone for graphics.
Image 10
IMAGE 1~10
User preset picture adjustment in IMAGE ADJUST Menu (P37).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
SVGA 1
Image 1
Press POINT UP/DOWN buttons to move a red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Move a red frame pointer to level
and press SELECT button.
Real
Picture level with improved halftone for graphics.
IMAGE 1~10
User preset picture adjustment in IMAGE ADJUST Menu (P37).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
PICTURE SCREEN SELECT (DIRECT)
SCREEN button
Select picture screen among Normal, Full and True by pressing
SCREEN button on Remote Control Unit.
Normal
Full
True
PICTURE SCREEN SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
SCREEN Menu icon
Press POINT UP/DOWN buttons and move a red frame pointer to
function that you want to select and then press SELECT button.
Move a red frame pointer to function
and press SELECT button.
Normal
Provides image to fit the panel size of the screen.
NOTE
Full
● Picture screen adjustment can not be operated
when “720p (HDTV)”, “1035i (HDTV)” or “1080i
(HDTV)” is selected on PC SYSTEM Menu (P25).
Provides image to fit the horizontal size of the screen.
● True and Digital zoom +/- can not be selected
when “480i”, “575i”, “480p” or “575p” is selected on
PC SYSTEM Menu (P25).
True
Provides image in its original size. When the original image size is
larger than screen size (1366 X 768), this projector enters “D. Zoom
+” mode automatically.
● This projector cannot display any resolution higher
than 1600 X 1200. If your computer’s screen
resolution is higher than 1600 X 1200, reset
resolution to lower before connecting projector.
Digital zoom +
● Image data in other than XGA (1024 x 768) is
When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. zoom +” is displayed. Press SELECT button to
expand image size. And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image. Panning function can work only when image
is larger than screen size.
modified to fit screen size in initial mode.
● Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.
A projected image can be also expanded by pressing D.ZOOM and
SELECT button on Remote Control Unit.
Digital zoom –
When Digital zoom – is selected, ON-SCREEN MENU disappears
and message “D. zoom –” is displayed. Press SELECT button to
compress image size.
A projected image can be also compressed by pressing D.ZOOM
and SELECT button on Remote Control Unit.
To cancel Digital Zoom +/– mode, press any button except D.ZOOM,
SELECT and POINT buttons.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING INPUT SOURCE
DIRECT OPERATION
INPUT button
Select INPUT source by pressing INPUT button on Top Control or on
Remote Control Unit.
Input 1
Select INPUT source by pressing INPUT 1, INPUT 2 or INPUT 3
button on Remote Control Unit.
Input 2
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
Input 3
SELECTING INPUT SOURCE
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connecting to those equipment, select a type of Video
source in SOURCE SELECT Menu.
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
INPUT Menu icon.
Input
SVGA 1
1
INPUT Menu icon
Input 1
Input 2
Input 3
Press POINT UP/DOWN buttons to move a red arrow pointer to
Input 2 and then press SELECT button. Source Select Menu will
appear.
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
2
Move a pointer to source that you want to select and then press
SELECT button.
Input 2
3
Source Select Menu
When video input signal is connected to VIDEO jack,
select Video.
Video
Move a pointer (red
arrow) to Video or
Y, Pb/Cb, Pr/Cr and
press SELECT button.
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y,Pb/Cb,Pr/Cr
NOTE;
INPUT SOURCE changes if the INPUT 2 button on Remote Control
Unit is pressed.
WHEN SELECT INPUT 3 (AV TERMINALS )
When connecting to those equipment, select a type of Video
INPUT MENU
source in SOURCE SELECT (VIDEO) Menu.
Input
SVGA 1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
INPUT Menu icon.
1
Input 1
INPUT Menu icon
Input 2
Input 3
Move a pointer (red arrow) to
Input 3 and press SELECT
button.
Press POINT UP/DOWN buttons to move a red arrow pointer to
Input 3 and then press SELECT button. Source Select Menu will
appear.
2
Input 3
Move a pointer to source that you want to select and then press
SELECT button.
3
Source Select Menu (VIDEO)
Move a pointer (red arrow)
to source and press
SELECT button.
When video input signal is connected to VIDEO jack,
select Video.
Video
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.
Y,Pb/Cb,Pr/Cr
When video input signal is connected to S-VIDEO jack,
select S-Video.
S-Video
NOTE;
INPUT SOURCE changes if the INPUT 3 button on Remote Control
Unit is pressed.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to AV
SYSTEM Menu icon.
1
2
Press POINT UP/DOWN buttons to move a red arrow pointer to
system that you want to select and then press SELECT button.
VIDEO JACK OR S-VIDEO JACK
AV SYSTEM MENU (VIDEO OR S-VIDEO)
Auto
Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
Auto
System
Auto
AV SYSTEM Menu icon
This box indicates system
being selected.
PAL
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
SECAM
NTSC
If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
NTSC4.43
PAL-M
PAL-N
Move a pointer (red
arrow) to system and
press SELECT button.
Y, Pb/Cb, Pr/Cr JACKS
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
Auto
System
When Video System is 1035i or 1080i, select system manually first.
AV SYSTEM Menu icon
This box indicates system
being selected.
COMPONENT VIDEO SIGNAL FORMAT
Move a pointer (red
arrow) to system and
press SELECT button.
If projector cannot reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE IMAGE SELECT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1 to Image 10 by
pressing IMAGE button on Top Control or IMAGE SELECTION ▲/▼
button on Remote Control Unit.
IMAGE button
Standard
Cinema
Image 1
Image 10
Standard
Normal picture level preset on this projector.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1~10
User preset picture adjustment in IMAGE ADJUST Menu (P37).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Image 1
Auto
Press POINT UP/DOWN buttons to move a red frame pointer to
level that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Move a red frame pointer to level
and press SELECT button.
Normal picture level preset on this projector.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1~10
User preset picture adjustment in IMAGE ADJUST Menu (P37).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
PICTURE SCREEN SELECT (DIRECT)
SCREEN button
Select picture screen among Full, Normal, Zoom and Natural wide by
pressing SCREEN button on Remote Control Unit.
Full
Normal
Zoom
Natural wide
PICTURE SCREEN SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
Press POINT DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.
SCREEN Menu icon
Move a red frame pointer to function
and press SELECT button.
Full
Provides image to fit width of screen by expanding image width
uniformly. This function can be used for providing a squeezed video
signal at wide video aspect ratio of 16 : 9.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select Full on this SCREEN Menu to provide better
quality.
NOTE : SCREEN Menu can not be operated when
“720p”, “1035i” or “1080i” is selected on AV
SYSTEM Menu (P32).
Normal
Provides image at the normal video aspect ratio of 4 : 3.
Zoom
Provides image to fit screen size (16 : 9 aspect ratio) by expanding
image width and height uniformly. This function can be used for
providing a letter box mode picture (4 : 3 aspect picture with black
bar on top and bottom edges) at wide video aspect of 16 : 9.
Natural wide
Provides image to fit width of screen by expanding both sides of
image. This function is suitable to provide a normal video signal (4 :
3 aspect ratio) at wide video aspect ratio of 16 : 9.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
PICTURE IMAGE ADJUSTMENTS
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.
IMAGE ADJUST MENU
1
2
Auto
Contrast
Press POINT UP/DOWN buttons to move a red frame pointer to
item that you want to adjust and then press SELECT button.
Level of each item is displayed. Adjust each level by pressing
POINT LEFT/RIGHT buttons.
IMAGE ADJUST
Menu icon
Move a red frame pointer to
item to be selected and then
press SELECT button.
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Color
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deepen color. (From 0 to 63.)
Tint
Press POINT LEFT button or POINT RIGHT button to obtain proper
color. (From 0 to 63.)
Color Management
The Color management function can be used to adjust the level,
phase and gamma of the selected display colors (except black, white
and gray) on the screen, and to replace these colors with other col-
ors if required.
The projector lets you replace up to eight colors for each image.
There are ten preset images for VIDEO mode and ten preset images
for PC, giving a total of twenty images.
Press POINT LEFT/RIGHT buttons
to adjust value.
Press the POINT UP/DOWN buttons to move a red frame point-
er to "COLOR MANAGEMENT", and then press the SELECT
button. The COLOR MANAGEMENT menu will appear and
pointer mode will be enabled. The image that was being project-
ed when the button was pressed will be paused, and the COLOR
MANAGEMENT POINTER will appear.
1
POINTER MODE
COLOR
MANAGEMENT
POINTER
Use the POINT buttons to move a pointer to a section of the
paused image that contains the color that you would like to
adjust, and then press the SELECT button. The mode will
change to COLOR SELECTION mode, and the color in the cen-
ter of the pointer will be selected and adjustment will be possi-
ble.
2
NOTE;
Press the COLOR M. button on the remote con-
trol to display the COLOR MANAGEMENT menu.
If you would like to check or re-adjust a color
management setting that has already been made,
press the COLOR M. button on the remote control
once more to change to LIST mode.
Use the POINT buttons to adjust the level and phase of the
color, and then press the SELECT button to confirm the setting.
Next, use the POINT buttons to adjust the gamma correction for
the color, and then press the SELECT button to accept the set-
ting. When the SELECT button is pressed, the mode will change
to LIST mode.
3
35
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
Move a red frame pointer to "MENU", and then press the
COLOR SELECTION
MODE
4
SELECT button. The COLOR MANAGEMENT menu will be
exited and the display will return to the IMAGE ADJUST menu.
(At this time, the image will stop being paused and normal pro-
jection will resume.) After changing the COLOR MANAGE-
MENT settings, use the IMAGE ADJUST menu to store the
changed settings.
Level and phase
adjustment palette.
Gamma
adjustment palette.
COLOR SELECTION MODE
COLOR M.
The mode will return to the pointer mode (even if you press the
MENU key on the projector or the remote control). (You will need to
reselect and re-adjust the color in this case.)
MENU
The COLOR MANAGEMENT menu will be exited and the display will
return to the normal projection screen, but any settings that have
been changed will not be stored. To store the changed settings, be
sure to select "LIST" using the POINT buttons and change to the
next mode (LIST mode).
LIST
COLOR M.
MENU
LIST MODE
COLOR PALETTE
DEL
LIST MODE
The check mark will be cleared and the effect of the setting adjustment
for that line on the projected images will be momentarily canceled.
COLOR PALETTE
The mode will return to COLOR SELECTION mode so that you can
re-adjust the setting for the color in that line. This option is not avail-
able if the check mark has been cleared by the operation immediate-
ly above.
ALL DEL
MENU
COLOR M.
DEL
The setting adjustment for the color in that line will be canceled.
NOTE;
If you press the COLOR M. button on the remote
control, the COLOR MANAGEMENT menu will be
exited and the display will return to the normal
projection screen, but any settings that have been
changed will not be stored. To store the changed
settings, be sure to select "MENU" using the
POINT buttons and store the settings.
ALL DEL
The setting adjustment for the colors in all lines will be canceled.
COLOR M.
The mode will return to POINTER mode.
Auto picture control
Press either POINT LEFT button or POINT RIGHT button to Auto
picture control position that you want to select . (Off, L1 or L2)
Off ······· Auto picture control OFF position.
L1 ········ Auto picture control LEVEL 1 position.
L2 ········ Auto picture control LEVEL 2 position.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE IMAGE
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
White balance (Red)
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Press SELECT button at this icon
to display other items.
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Sharpness
Press SELECT button at this icon
to display previous items.
Press POINT LEFT button to soften the image, and POINT RIGHT
button to sharpen the image. (From 0 to 31.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Press POINT LEFT/RIGHT buttons
to adjust value.
Noise reduction
Press POINT LEFT/RIGHT buttons to change noise reduction mode.
Dialog box display is changed to “Off”, “L1”, “L2”.
Off ··· Noise reduction mode to OFF.
L1 ···· Noise reduction mode to L1.
L2 ···· Noise reduction mode to L2.
Progressive
Press POINT LEFT/RIGHT buttons to change progressive scan
mode. Dialog box display is changed to “Off”, “On”, “Film”.
Off ···Progressive scan mode to OFF.
On ····Progressive scan mode to ON.
Film ···· Effective on 3:2 pulldown video sources.
Other icons operates as follows.
Reset
Reset all adjustment to previous figure.
Store
To store manually preset image, move a red frame pointer to Store
icon and press SELECT button. Image Level Menu will appear.
Move a red frame pointer to Image 1 to 10 where you want to set and
then press SELECT button.
Image Level Menu
Move a red frame pointer to
any of Image 1 to 10 where
you want to set and then
press SELECT button.
Quit
Closes IMAGE ADJUST MENU.
Store icon
Press SELECT button at this
icon to store the adjustment.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
This projector has Setting menu that allows you to set up the other
SETTING MENU (LANGUAGE)
various functions described as follows;
Language
SVGA 1
Press the MENU button to display the On-Screen Menu.
Press the POINT LEFT/RIGHT buttons to move a red frame
pointer to the Setting Menu icon.
1
SETTING Menu icon
Set a red frame
pointer to the item
and press the
Press the POINT DOWN button to move a red frame pointer
2
to the item that you want to set and then press the
SELECT
SELECT button.
button. The Setting dialog box appears.
Language
The language used in the On-Screen Menu is available in English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean, or Japanese.
Keystone
This function corrects distortion of a projected image. Select either
Store or Reset with the POINT LEFT/RIGHT buttons, and then
press the SELECT button. The keystone dialog box appears.
Adjust keystone with the POINT UP/DOWN/LEFT/RIGHT buttons.
When pressing the SELECT
button at Language, the
Language Menu appears.
Store . . . . . stores the keystone adjustment even if the AC power
cord is disconnected.
Reset . . . . .resets the keystone adjustment when the AC power
cord is disconnected.
Background
3 background settings are available in this projector. Select one of
the followings when no input source is connected to the projector
or no input signal is coming from the connected equipment:
Blue . . . . . .blue colored background
My logo . . .the image you captured
Black . . . . .black colored background
Display
This function decides whether to display On-Screen Displays.
Off . . . . . . .
does not show On-Screen Display except;
●
●
●
On-Screen Menu
“Power off?” message
“No signal” message
●
●
”Please wait....”
Color management operation screen
Count-down Off does not show Count-down Display.
On . . . . . . . shows all the On-Screen Display.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Logo
Logo settings can be altered as follows:
Logo
Logo select
This function decides what to be displayed on the starting-up dis-
play as follows:
Off . . . . . . .count-down only
Default . . . .the factory-set logo
User . . . . . .the image you captured
Capture
This function enables you to capture the image being projected
and use it for a starting-up display.
After capturing the projected image, go to the Logo function and
set it to “User”. Then the captured image can be displayed when
turning on the projector next time.
To capture the image, select [Yes]. To cancel the Capture
function, select [No].
Select [Yes] to capture
the projected image.
NOTE;
Select [Yes] to
stop capturing.
• Before capturing an image, select Standard in the Image Select Menu
to capture a proper image. (See page 29, 33.)
• A signal from a computer can be captured up to XGA (1024 X 768).
• Certain signals may not be captured properly.
• When capturing the image that has been adjusted by the Keystone
function, the adjustment data is automatically reset and the projector
captures an image without keystone correction.
• When starting to capture a new image, the previously stored image is
cleared even if you cancel the capturing.
• Once you exit the Logo menu after setting Logo lock to "On", you are
required to enter the PIN code every attempting to change the Logo
setting.
Logo PIN Code Lock Dialog Box
Logo PIN Code Lock
This function prevents an unauthorized person from changing the
Logo setting.
Pointer
Off . . . . .the Logo setting can be changed freely from the
Logo menu.
Quit
On . . . . .the Logo setting cannot be changed without the
Logo PIN code.
After a correct Logo PIN code is entered, the
following dialog box will appear.
If you want to change the Logo PIN Code Lock setting, enter a
Logo PIN code along the following steps. The initial Logo PIN code
is set "4321" at the factory.
Enter a Logo PIN code
Select a number by pressing the POINT LEFT/RIGHT buttons and
fix the number with the SELECT button. The number will change
to "✳". If you fixed a wrong number, move the pointer to "Set" or
"Clear" once by pressing the POINT DOWN button, then return to
"Logo PIN code". Enter the correct number again.
Select On/Off by pressing the POINT LEFT/RIGHT
buttons or change the Logo PIN code.
Change the Logo PIN code
Logo PIN code can be changed to your desired four-
digit number. Select "Logo PIN code change" with
the POINT DOWN button and press the SELECT
button. Set a new Logo PIN code.
Repeat this step to complete entering a four-digit number.
When the four-digit number is fixed, the pointer will automatically
move to "Set". Press the SELECT button so that you can change
the Logo PIN code lock setting.
Be sure to note the new Logo PIN code and keep it
at hand. If you lost the number, you could no longer
change the Logo PIN code setting. For details on
PIN code setting, refer to relevant instructions of the
PIN Code Lock function on page 42.
If you entered a wrong Logo PIN code, "Logo PIN code" and the
number (✳✳✳✳) will turn red and disappear. Enter a correct Logo
PIN code all over again.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Ceiling
Ceiling
When this function is “On,” the picture is top/bottom and left/right
reversed. This function is used to project the image from a ceiling
mounting the projector.
Rear
When this function is “On,” the picture is left/right reversed. This
function is used to project the image to a rear projection screen.
Rear
Simple menu
When this function is “On,” the value adjustment bar in the picture
image adjustment menu is displayed on the bottom left of the
screen.
Power management
Simple menu
For reducing power consumption as well as maintaining the lamp
life, the Power Management function turns off the projection lamp
when the input signal is interrupted and no button is pressed for 30
seconds or more.
Value adjustment bar
If the input signal is interrupted and no button is pressed for 30
seconds or more, the timer display with the message "No signal"
appears on the screen. The count-down of the set time will get
started. The count-down time can be set between 1 and 30 min-
utes.
Power management
When the count-down time has been elapsed, the lamp will be
turned off to cool itself down. The READY indicator will be
switched off during this cooling-off period. The next operation
depends on the setting as follows :
Time left until Lamp off
Ready . . . . .When the lamp has been fully cooled down, the
READY indicator starts flashing. In this condition,
the projection lamp will be turned on if the input
signal is reconnected or any button on the top
control or remote control unit is pressed.
Shutdown . . .When the lamp has been fully cooled down, the
power will be turned off.
Press the SELECT button at
Power management and this
box appears. Choose one of
three settings with the POINT
LEFT/RIGHT buttons, and go
to the timer with the POINT
DOWN button and set time
with the POINT LEFT/RIGHT
buttons.
Off . . . . . . . . .The Power Management function is canceled.
On start
When this function is “On,” the projector is automatically turned on
just by connecting the AC power cord to a wall outlet.
NOTE;
Be sure to turn the projector off properly (see “Turning Off the Projector”
on page 21). If the projector is turned off in the incorrect sequence, such
as disconnecting the AC power cord before completing the cool down
etc., the On start function does not operate properly.
Lamp control
This function allows you to change brightness of the screen.
···· brightness according with the input signal.
···· normal brightness.
···· lower brightness reduces the lamp power consumption
and extends the lamp life.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Remote control
Remote control
This projector provides eight different remote control codes (Code
1-Code 8); the factory-set, initial code (Code 1) and the other
seven codes (Code 2 to Code 8). This switching function prevents
remote control interference when operating several projectors or
video equipment at the same time.
For example operating the projector in “Code 7”, both the projector
and the remote control must be switched to “Code 7”.
To change the code for the projector;
Select a remote control code in this Setting Menu.
To change the code for the remote control;
Check the Reset Switch to "Use position" in the compartment lid
on back of the remote control.
And then while holding down the MENU button, press the IMAGE
button number of times corresponding to the remote control code
for the projector.
When pressing the SELECT
button at Remote control, the
remote control code menu
appears.
To reset the code for the remote control;
Slide the Reset Switch to "Reset position" in the compartment lid
on back of the remote control.
Reset position
Use position
Reset switch
Security
Security
Key lock
This function locks operation of the top control and remote control.
It is useful to prevent operation by an unauthorized person.
···· not locked.
···· locks operation of the top control. To unlock, use the
remote control.
···· locks operation of the remote control. To unlock, use
the top control.
If the top control accidentally becomes locked and you do not have
the remote control nearby, disconnect the AC power cord from the
AC outlet, and then with pressing the SELECT button, reinsert the
AC power cord. This will cancel the top control lock.
Key lock
Select Key lock and
this box appears.
Choose one of
these with the
POINT UP/DOWN
buttons and select
[Yes] to activate it.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
PIN code lock
PIN code lock
SVGA1
Security
This function prevents the projector from being operated by an
unauthorized person and provides the following settings for
security options.
...............the projector is not locked with the PIN code.
Off
.............requires to enter the PIN code every time turning on
the projector.
On1
..........requires to enter the PIN code to operate the
projector once the power cord is disconnected; as
long as the AC power cord is connected, the
projector can be operated without the PIN code.
On2
When the projector is
locked with the PIN
code, the PIN code
lock mark appears on
the menu bar.
Whenever to change the PIN Code Lock setting or the PIN code
(the four-digit number), you are required to enter the PIN code.
"1234" is set as the initial PIN code at the factory.
Enter a PIN code
Pointer
Enter a PIN code
Select a number by pressing the POINT LEFT/RIGHT buttons
and fix the number with the SELECT button. The number will
change to "✳". If you fixed a wrong number, move the pointer to
"Set" or "Clear" once by pressing the POINT DOWN button,
then return to "PIN code". Enter the correct number again.
Repeat this step to complete entering a four-digit number.
Quit
When the four-digit number is fixed, the pointer will
automatically move to "Set". Press the SELECT button so that
you can change the following PIN code lock settings.
The input numbers
change to “✳” for
security.
If you entered a wrong PIN code, "PIN code" and the number
(✳✳✳✳) will turn red and disappear. Enter a correct PIN code
all over again.
When the pointer
automatically move
to "Set", press the
SELECT button.
To Change the PIN Code Lock setting
Select Off, On1, or On2 with the POINT LEFT/RIGHT buttons
and then "Quit" with the POINT DOWN button and press the
SELECT button to close the dialog box.
Change the PIN Code Lock setting
Select a desired
setting with the
POINT
LEFT/RIGHT
buttons.
To Change the PIN Code
The PIN code can be changed to your desired four-digit
number.
Select "PIN code change" with the POINT DOWN button, and
press the SELECT button. The New PIN code input dialog box
will appear.
Change the PIN code
Select PIN code
change and press
the SELECT button.
The New PIN code
input dialog box will
appear.
Select a number with the POINT LEFT/RIGHT buttons and fix
the number with the SELECT button. Repeat it to complete
entering a four-digit number. When the four-digit number is
fixed, the pointer will automatically move to "Set". Then press
the SELECT button.
CAUTION:
WHEN YOU HAVE CHANGED PIN CODE, WRITE DOWN THE
NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO
ON PAGE 59, AND KEEP IT SECURELY. SHOULD THE PIN
CODE BE LOST OR FORGOTTEN, THE PROJECTOR CAN NO
LONGER BE OPERATED.
The input numbers
are being displayed
for confirmation.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Lamp counter
This function is used to reset the lamp replace counter. When
replacing the projection lamp, reset the lamp replace counter by
using this function. See page 47 for operation.
Factory default
Factory default
This function returns all setting values except for the user logo,
Key lock, PIN code lock, logo PIN code lock and the lamp counter
to the factory default settings.
Select Factory default and this
box appears. Select [Yes] , and
the next box appears.
Select [Yes] to
activate it.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MAINTENANCE
WARNING TEMP. INDICATOR
The Warning Temp. Indicator flashes red to let you know the internal temperature
of the projector exceeds the normal level. If the temperature goes up further, the
projector will be turned off automatically and the Ready indicator will go out. (The
Warning Temp. Indicator continues flashing.) After the cooling-off period, the
Ready Indicator lights on again and the projector can be turned on by pressing the
On/Off button on the remote control unit or on the top control. When you turn on
the projector, the Warning Temp. Indicator will go out.
TOP CONTROL
Ready
Warning Temp.
Indicator
Indicator
If the Warning Temp. Indicator is still flashing, check the followings;
Ventilation Slots of a projector may be blocked. In such an event, reposition
a projector so that Ventilation Slots are not obstructed.
1
Air Filter may be clogged with dust particles. Clean Air Filter by following
section AIR FILTER CARE AND CLEANING on next page.
2
If WARNING TEMP. Indicator remains on after performing above checks,
Cooling Fans or Internal Circuits may be malfunctioning. Contact the service
station.
3
When both of the Warning Temp. and Ready indicators are flashing:
When the projector detects an internal problem, it will shut down automatically and both of the Warning temp. and Ready
Indicators start flashing. In this condition, the projector cannot be turned on even if you press the On/Off button on the
remote control unit or on the top control. If this case happenes, disconnect and reconnect the AC power cord, and then turn
on the projector again to check its operation. If the projector shuts down again or fails to be turned on, the internal check and
repair will be required. Plug off the AC power cord and contact service station.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
AIR FILTER CARE AND CLEANING
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become
clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely
affect life of a projector. Clean Air Filter following steps below:
Turn off a projector, and disconnect AC power cord from AC
outlet.
1
Turn a projector upside down and remove Air Filter (2 used) by
pulling latches upward.
2
Clean Air Filter with a brush or wash out dust and particles.
3
4
Replace Air Filter properly. Make sure that Air Filter is fully
inserted.
CAUTION
Do not operate a projector with Air Filter removed. Dust
may accumulate on LCD Panel and Projection Mirror
degrading picture quality.
Do not put small parts into Air Intake Vents. It may result
in malfunction of a projector.
AIR FILTER
Pull up and remove.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments
may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements
inside a projector. This condition may degrade quality of a projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
CLEANING PROJECTION LENS
Follow these steps to clean Projection Lens:
Turn off a projector, and disconnect AC power cord from AC outlet.
1
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
2
Lightly wipe a cleaning cloth over Projection Lens.
3
4
When a projector is not in use, replace Lens Cover.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT
LAMP REPLACE
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow. If this indicator lights
yellow, replace the projection lamp with a new one promptly.
TOP CONTROL
This indicator lights yellow
when the life of the projection
lamp draws to an end.
Replace the Projection Lamp
with a new one promptly.
CAUTION
Allow a projector to cool, for at least 45 minutes before
you open Lamp Cover. The inside of a projector can
become very hot.
For continued safety, replace with a lamp assembly of
the same type.
Do not drop a lamp assembly or touch a glass bulb! The
glass can shatter and may cause injury.
Follow these steps to replace lamp assembly.
Turn off a projector and disconnect AC plug. Allow a projector to
cool for at least 45 minutes.
1
Loosen 2 screws with a screwdriver and open Lamp Cover.
2
3
Loosen 2 screws with a screwdriver and pull out Lamp Assembly
by grasping Handle.
LAMP COVER
HANDLE
Replace Lamp Assembly with a new one and tighten 2 screws
back. Make sure that Lamp Assembly is set properly. Replace
Lamp Cover and tighten 2 screws.
4
LAMP
ASSEMBLY
Connect AC Power Cord to a projector and turn it on.
5
6
Reset Lamp Replace Counter (refer to next page “LAMP
REPLACE COUNTER” section).
NOTE : Do not reset Lamp Replace Counter when Projection
Lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the
following information to the dealer.
● Model No. of your projector
● Replacement Lamp Type No.
:
:
LC-W3
POA-LMP98
(Service Parts No. 610 325 2957)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACE COUNTER
Be sure to reset the Lamp Replace Counter after the Lamp Assembly is replaced. When the Lamp Replace Counter is reset,
the LAMP REPLACE Indicator stops lighting.
Lamp counter
Turn projector on, press MENU button and ON-SCREEN
1
MENU will appear. Press POINT LEFT/RIGHT buttons to
move a red frame pointer to SETTING Menu icon (refer to
page 43).
Press POINT UP/DOWN buttons to move a red frame pointer
2
to “Lamp counter” and then press
SELECT button. The next
box appears.
Select Lamp counter and this box
appears. Select [Reset] , and the
next box appears.
Press POINT UP/DOWN buttons to select “Reset” and then
3
4
press
SELECT button. The message "Lamp replacement
counter reset?" is displayed. Move the pointer to [Yes] and
then press SELECT button.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.
Select [Yes] and the next box
appears.
Select [Yes] to
activate it.
NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING
PROJECTOR" on pages 12 ~ 14.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.
Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to
turn computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and
computer.)
6. If problem still exists, check following chart.
Problem:
No power.
Try these Solutions
● Plug a projector into your AC outlet.
● Make sure READY Indicator lights.
● Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
● Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY
indicator flashes, a projector cannot be turned on.
(See "TURNING ON/OFF PROJECTOR" section on pages 20-21.)
● Check Projection Lamp. (Refer to page 46.)
● Adjust focus of a projector.
● Make sure a projection screen is at least 5.0’ (1.5m) from a projector.
● Check Projection Lens to see if it needs cleaning.
Image is out of
focus.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens. In such an event, leave a
projector OFF and wait until condensation disappears.
● Check Ceiling/Rear feature. (See “SETTING” section on page 40.)
Picture is Left/Right
reversed.
● Check Ceiling feature. (See “SETTING” section on page 40.)
Picture is
Top/Bottom
reversed.
● Check Display feature.(See “SETTING” section on page 38.)
Some displays are
not seen during
Operation.
● Check connection between your computer or video equipment and a projector.
● When turning a projector on, it takes about 20 30 seconds to display an image.
No image.
~
● Check system that you select is corresponding with your computer or video equipment.
● Make sure temperature is not out of Operating Temperature 41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C).
● Check audio cable connection from audio input source.
● Adjust audio source.
No sound.
● Press VOLUME (+) button.
● Press MUTE button.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solutions
● Check batteries.
● Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
● Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Check remote control code from Remote Control Unit.
(See“SETTING” section on page 41.)
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOT-
ING" section on pages 48, 49. To correct failure, try "Solutions".
If after following all operating instructions, you find that service is necessary, contact Eiki Service Station or store
where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
49
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MENU TREE
Computer Input/Video Input
Input 1
RGB (PC analog)
RGB (Scart)
Go to System (1)
Input
N/A
N/A
N/A
RGB (PC digital)
RGB (AV HDCP)
Input 2
Input 3
Video
Go to System (2)
Go to System (3)
Go to System (1)
Y, Pb/Cb, Pr/Cr
RGB
Go to System (2)
Go to System (3)
Go to System (2)
Video
Y, Pb/Cb, Pr/Cr
S-video
✽N/A - - - not applicable
Computer Input
Image Select
Standard
Real
Image 1
MODE 1
MODE 2
SVGA 1
SVGA 2
SVGA 3
System (1)
Image 10
PC Adjust
Auto PC Adj.
Fine sync.
Total dots
Position H
Position V
Current mode
Clamp
0 - 31
Display area - H
Display area - V
Reset
Yes/No
Mode free
Store
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
Quit
Screen
Normal
Full
True
D.zoom +
D.zoom –
Quit
50
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Video Input
Computer Input/Video Input
Setting
Language
English
German
French
Italian
System (2)
Auto
PAL
SECAM
NTSC
Spanish
Portuguese
Dutch
Swedish
Russian
Chinese
Korean
NTSC 4.43
PAL-M
PAL-N
Auto
1080i
1035i
720p
575p
480p
575i
System (3)
Japanese
Quit
Keystone
Store/Reset
Blue/My logo/Black
Background
Display
480i
Off/Countdown Off/On
Logo
Logo select
Capture
Off/Default/User
Image Select
Standard
Cinema
Image 1
Yes/No
Logo PIN code lock
Quit
On/Off
Logo PIN code change
Image 10
Quit
On/Off
On/Off
On/Off
Ceiling
Rear
Screen
Full
Normal
Zoom
Simple menu
Off
Power management
Natural wide
Ready
Shut down
1-30 Min
Quit
Computer Input/Video Input
Image Adjust
Contrast
Brightness
Color
0 - 63
0 - 63
0 - 63
0 - 63
On/Off
On start
Lamp control
Auto/Normal/Eco
Tint
Remote control
Code 1
Color management
Color
Gamma
List
Code 8
Quit
All Del
Menu
Color M.
Menu
Off
Security
Key lock
Color M.
Projector
Remote Control
Quit
Auto picture control
Color Temp
Off/L1/L2
High
Mid
Low
Off/On1/On2
PIN code change
Quit
Pin code lock
XLow
Red
Green
0 - 63
0 - 63
Lamp counter
Factory default
Blue
0 - 63
0 - 31
0 - 15
Off/L1/L2
Off/On/Film
Yes/No
Image 1
Yes / No
Yes / No
Sharpness
Gamma
Noise reduction
Progressive
Reset
Store
Image 10
Quit
Quit
Sound
Volume
0 - 63
Mute
Quit
On/Off
51
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 140 MHz of Dot Clock.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17
SXGA 18
SXGA 19 1280 x 1024
SXGA 20 1280 x 1024
SXGA+ 1 1400 x 1050
SXGA+ 2 1400 x 1050
SXGA+ 3 1400 x 1050
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
63.97
65.35
65.12
75.00
80.00
48.36
47.70
48.36
56.16
75.00
81.25
87.50
93.75
45.00
37.50
33.75
33.75
28.125
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
86.00
94.00
60.01
72.00
66.00
86.70
60.18
85.024
60.19
60.12
59.90
75.08
75.08
60.00
60.00
60.00
72.00
60.00
65.00
70.00
75.00
60.00
50.00
60.00
60.00
50.00
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480i
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
31.47
31.25
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
58.03
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
60.00
50.00
59.88
50.00
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
87.17
77.07
75.70
86.96
58.20
58.30
72.00
––––––––
(Interlace)
––––––––
(Interlace)
––––––––
(Progressive)
––––––––
(Progressive)
575i
480p
575p
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA15
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
1152 x 900
1280 x 1024
(Interlace)
MAC
MAC
1280 x 960
1280 x 1024
1366 x 768
1360 x 768
1376 x 768
1360 x 768
1600 x 1200
1600 x 1200
1600 x 1200
1600 x 1200
WXGA 1
WXGA 2
WXGA 3
WXGA 4
UXGA1
UXGA2
UXGA3
UXGA4
720p
720p
1035i
1080i
1080i
1024 x 768
(Interlace)
1024 x 768
1024 x 768
––––––––
(Progressive)
––––––––
(Progressive)
––––––––
(Interlace)
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
––––––––
(Interlace)
––––––––
(Interlace)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
When a input signal is digital from DVI terminal, refer to chart below.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
✳
✳
D-VGA
D-480p
D-575p
D-SVGA
D-XGA
640 x 480
31.47
31.47
31.25
37.879
43.363
48.36
47.70
48.36
46.50
63.98
59.94
59.88
50.00
60.32
60.00
60.00
60.00
60.00
50.00
60.02
D-SXGA2
D-SXGA+ 1400 x 1050
D-720p
1280 x 1024
60.276
63.97
45.00
37.50
33.75
33.75
28.125
33.75
28.125
27.00
58.069
60.19
60.00
50.00
60.00
60.00
50.00
60.00
50.00
48.00
720 x 480
(Progressive)
1280 x 720
(Progressive)
768 x 575
(Progressive)
1280 x 720
(Progressive)
D-720p
800 x 600
1920 x 1035
(Interlace)
D-1035i
1024 x 768
1920 x 1080
(Interlace)
D-1080i
D-WXGA1 1366 x 768
D-WXGA2 1360 x 768
D-WXGA3 1376 x 768
D-WXGA5 1368 x 768
D-SXGA1 1280 x 1024
1920 x 1080
(Interlace)
D-1080i
D-1080psf/30
D-1080psf/25
D-1080psf/24
1920 x 1080
1920 x 1080
1920 x 1080
✳
Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.
✳
NOTE : Specifications are subject to change without notice.
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.
Indicators
Projector Condition
WARNING
TEMP.
red
LAMP
REPLACE
yellow
READY
green
LAMP
red
The projector is OFF. (The AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER ON-
OFF button.
✽
✽
The projector is operating normally.
The Warning Temp. Indicator flashes red to let you know the
internal temperature of the projector exceeds the normal level. If
the temperature goes up further, the projector will be turned off
automatically and the Ready indicator will go out. When the pro-
jector is cooled down enough and the temperature returns to nor-
mal, the READY indicator lights green and the projector can be
turned on. (The WARNING TEMP. indicator keeps flashing.)
Check and clean the Air Filter.
✽
The projector is cooled down enough and the temperature
returns to normal. When turning on the projector, the WARNING
TEMP. indicator stops flashing. Check and clean the Air Filter.
✽
• • • on
• • • flashing
• • • dim
• • • off
53
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Indicators
Projector Condition
WARNING
READY
TEMP.
green
LAMP
REPLACE
yellow
LAMP
red
red
The projector is being cooled down. It cannot be turned on until
the READY indicator lights green.
✽
The projector detects an abnormal condition and cannot be
turned on. Unplug the AC Power Cord and plug it again to turn
on the projector. If the projector is turned off again, disconnect
the AC Power Cord and contact the dealer or the service center
for service and checkup. Do not leave the projector on. It may
cause electric shock or a fire hazard.
The projector is in the Power management mode.
✽
✽
The temperature inside the projector is abnormally high.
The temperature inside the projector is abnormally high. The pro-
jector cannot be turned on. When the projector is cooled down
enough and the temperature returns to normal, the READY indi-
cator lights green and the projector can be turned on.
✽
The lamp cannot light up. (The projector is preparing for stand-
by or the projection lamp is being cooled down. The projector
cannot be turned on until cooling is completed.)
The lamp cannot light up. (The lamp has been cooled down
enough and the projector is in stand-by mode and ready to be
turned on with the POWER ON-OFF button.)
The life of the projection lamp draws to an end.
Replace the lamp and then reset the Lamp time. The indicator
will turn off.
✽
• • • on
• • • flashing
• • • dim
• • • off
✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow,
replace the projection lamp with a new one promptly. Reset the Lamp Replace Counter after replacement of the lamp.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
12.6" x 6.6" x 16.8" (319 mm x 168 mm x 429.5 mm)
19.2 lbs (8.7 kg)
(W x H x D)
Dimensions
Net Weight
1.21" TFT Active Matrix type, 3 panels
1366 x 768 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
3,147,264 (1366 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i and 1080i
H-sync. 15 ~ 100 KHz, V-sync. 48 ~ 100 Hz
F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focus
5.0' (1.5 m) ~ 52.2' (15.9 m)
High Definition TV Signal
Scanning Frequency
Projection Lens
Throw distance
Up and Down
Motorized Lens Shift
Projection Image Size (Diagonal)
Horizontal Resolution
Projection Lamp
Input 1 Jacks
Adjustable from 30" to 400"
800 TV lines
300 watt type
DVI Terminal (Digital) HDCP Compatible, HDB 15-pin Terminal (Analog)
and Stereo Mini Type Jack (Audio)
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V),
Stereo Mini Type Jack (Audio)
Input 2 Jacks
Input 3 Jacks
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)
and DIN 4-pin (S-Video)
DIN 8-pin (Control port), Wired Remote Jack and Pj-to NetDirector Connector
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
0˚ to 10.5˚
Other Jacks
Built-in Speakers
Feet Adjustment
Voltage and Power
Consumption
AC 100 ~ 120 V (5.0 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (2.5 A Max. Ampere), 50 / 60 Hz (Continental Europe)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
Operating Temperature
Storage Temperature
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Power Source
Operating Range
Dimensions
:
:
:
:
AA or R06 1.5V ALKALINE Type x 2
16.4’ (5m) / 30˚
1.97” x 1.06” x 6.61” (50mm x 27mm x 168mm)
4.4 oz (126 g) (including batteries)
Remote Control Transmitter
Net Weight
Owner’s Manual (Print and CD-ROM)
AC Power Cord
Accessories
Wireless/Wired Remote Control Transmitter and Batteries
Control Cable for Serial port
Lens Cap
PIN Code Label
● Specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a
tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
PJ LINK NOTICE
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries
Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard
Class 1.
EIKI Projector Input
PJLink Input
RGB 1
Parameter
RGB (PC (Analog)
11
12
31
32
21
22
13
23
24
25
INPUT-1
RGB (Scart)
RGB (PC Digital)
RGB (AV HDCP)
Video
RGB 2
DIGITAL 1
DIGITAL 2
VIDEO 1
VIDEO 2
RGB 3
INPUT-2
INPUT-3
Y, Pb/Cb, Pr/Cr
RGB
Video
VIDEO 3
Y, Pb/Cb, Pr/Cr
S-video
VIDEO 4
VIDEO 5
PJLink is a registered trademark of JBMIA.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
CONFIGURATIONS OF TERMINALS
COMPUTER INPUT-1 TERMINALS (ANALOG)
Terminal : HDB15-PIN
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
+5V Power
Pin Configuration
10 Ground (Vert.sync.)
11 Sense 0
12 DDC Data
2
1
5
4
3
10
9
8
7
6
15
14
13
12
11
Ground (Horiz.sync.) 13 Horiz. sync.
Ground (Red)
Ground (Green)
Ground (Blue)
14 Vert. sync.
15 DDC Clock
COMPUTER INPUT-1 TERMINAL (DIGITAL)
Terminal : DVI 24-pin
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
T.M.D.S. Data2+
9
T.M.D.S. Data1–
17 T.M.D.S. Data0–
18 T.M.D.S. Data0+
Pin Configuration
10 T.M.D.S. Data1+
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield
1
9
2
3
4
5
6
7
8
No Connect
No Connect
DDC Clock
DDC Data
12 No Connect
13 No Connect
14 +5V Power
15 Ground (for +5V)
16 Hot Plug Detect
20 No Connect
21 No Connect
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock–
10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
No Connect
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
PS/2
-----
Serial
R X D
-----
ADB
-----
Pin Configuration
1
2
3
4
5
6
7
8
CLK
DATA
GND
-----
ADB
-----
-----
8
7
6
GND
GND
-----
5
4
3
RTS / CTS
T X D
GND
2
1
-----
-----
GND
-----
-----
GND
GND
57
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPTIONAL PARTS
The parts listed below are optionally supplied. When ordering those parts, give the name and Type No. to the sales dealer.
● DVI Cable
Type No. : KA-DV20
● HDB 15 pin-SCART 21 pin Cable Type No. : AH-98881
● Long Zoom Lens
● Ultra Long Zoom Lens
● Short Zoom Lens
● Short Fixed Lens
● Pj-to NetDirector
Type No. : AH-23132
Type No. : AH-24241
Type No. : AH-23122
Type No. : AH-32011
Type No. : PjNET-300
LENS REPLACEMENT
The lens of this projector can be replaced with other optional lens which are sold separately. This feature enables you to use
the projector for wide variety of uses.
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be installed or replaced
by well-trained sales or service engineers. Do not attempt to do by yourself as it may cause injury.
After installing the lens, attach the lens cap to the lens when setting up the projector.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
PIN CODE NUMBER MEMO
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number
and unable to operate the projector, contact the service station.
PIN Code Lock No.
Factory default set No: 1 2 3 4*
Logo PIN Code Lock No.
Factory default set No: 4 3 2 1*
*Should the four-digit number be
changed, the factory set number will
be invalid.
While the projector is locked with the PIN code...
Put the label below (supplied) on in a prominent place of the
projector's body while it is locked with a PIN code.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
A-key to better communications
Canada
U.S.A.
EIKI International, Inc.
30251 Esperanza
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : [email protected]
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Eastern Europe
EIKIˆ CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7
Czech Republic
Tel : +42 02 20570024
+42 02 20571413
Fax : +42 02 20571411
E-Mail : [email protected]
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : [email protected]
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel : +81-6-6311-9479
Fax : +81-6-6311-8486
E-Mail : [email protected]
Printed in Japan
Part No. 610 329 6913 (1AA6P1P5176-- M4YB)
© 2006 Eiki International, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|