AH-50001
AH-50002
5 Insert the new lamp unit.
• Press the lamp unit firmly into the lamp unit
compartment. Fasten the securing screws.
• Be sure that AH-50001 and AH-50002 are re-
spective type.
LAMP UNIT (LAMP/CAGAE MHO-D5U0L0E0) F1O/RAPHR-O5JE0C0T0O2R
INSTALLATION MANUAL
Model
CAUTION:
• Potential hazard of glass particles if lamp ruptures. Please have an EIKI Authorized Dealer or Service Center
replace lamp if rupture occurs.
• Do not remove the lamp unit directly after operation of the projector.The lamp may be extremely hot.Wait at
least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before
removing the lamp unit.
6 Replace the lamp unit cover.
• Align the lamp unit cover and slide it to close.
Then tighten the user service screw to secure
the lamp unit cover.
■
It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi-
cant deterioration in the picture and color quality.The lamp life (percentage) can be checked with the on-screen display.
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
For Lamp 1
For Lamp 2
U.S.A. ONLY
Info
Compartment for
AH-50001
Compartment for
AH-50002
User service
screw
• If the lamp unit and lamp unit cover are not cor-
rectly installed, the power will not turn on, even if
the power cord is connected to the projector.
STANDBY-ON button
Removing and Installing the
Lamp Unit
Info
Resetting the Lamp Timer
• Make sure that you remove the lamp unit by the
handle. Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to the lamp,
be sure to carefully follow the steps below.
• Do not loosen other screws except for the lamp unit
cover and lamp unit.
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when re-
placing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the
lamp to become damaged or explode.
(Only the silver screws are loosened.)
To AC socket
1 Press
on the projector or
the remote control to put the projec-
tor into standby mode.
on
1 Connect the power cord.
•
Plug the power cord into the AC socket of the projector.
Power cord
STANDBY-ON button
• Wait until the cooling fan stops.
2 Reset the lamp timer.
Warning!
For Lamp 1
• Do not remove the lamp unit from the projector
right after use. The lamp and parts around the
lamp will be very hot and may cause burn or
injury.
• When you reset the timer for AH-50001, while
simultaneously holding down
press on the projector.
and
,
Power cord
ENTER button
MENU button
• “LAMP 1 100%” is displayed, indicating that the
lamp timer is reset.
2 Disconnect the power cord.
• Unplug the power cord from the AC socket.
• Leave the lamp until it has fully cooled down
(about 1 hour).
H&V LENS
SHIFT
button
2
For Lamp 2
1
• When you reset the timer for AH-50002, while
3 Remove the lamp unit cover.
• Loosen the user service screw (1) that se-
cures the lamp unit cover. Remove the lamp
unit cover (2).
User service screw
Handle
simultaneously holding down
press on the projector.
and
,
• “LAMP 2 100%” is displayed, indicating that the
lamp timer is reset.
4 Remove the lamp unit.
• Loosen the securing screws (two for each lamp)
from the lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the arrow.
At this time, keep the lamp unit horizontal and
do not tilt it.
Printed in China
9NK5010061000
07P03-CH-NM
Securing screws
AH50001_2_OptionLamp.p65
1
06.12.20, 9:36 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
|