Eiki CRT Television LC X71L User Manual

MULTIMEDIA PROJECTOR  
MODEL LC-X71  
LC-X71L (Lensless)  
OWNER’S MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
All the safety and operating instructions should be read before  
the product is operated.  
This projector should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supplied, consult your authorized dealer or  
local power company.  
Read all of the instructions given here and retain them for later  
use. Unplug this projector from AC power supply before  
cleaning. Do not use liquid or aerosol cleaners. Use a damp  
cloth for cleaning.  
Do not overload wall outlets and extension cords as this can  
result in fire or electric shock. Do not allow anything to rest on  
the power cord. Do not locate this projector where the cord  
may be damaged by persons walking on it.  
Follow all warnings and instructions marked on the projector.  
For added protection to the projector during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet. This will prevent damage  
due to lightning and power line surges.  
Do not attempt to service this projector yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
Unplug this projector from wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool, etc...  
Do not use attachments not recommended by the  
manufacturer as they may cause hazards.  
c. If the projector has been exposed to rain or water.  
d. If the projector does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the projector to normal operation.  
e. If the projector has been dropped or the cabinet has been  
damaged.  
f. When the projector exhibits a distinct change in  
performance-this indicates a need for service.  
Do not place this projector on an unstable cart, stand, or table.  
The projector may fall, causing serious injury to a child or  
adult, and serious damage to the projector. Use only with a  
cart or stand recommended by the manufacturer, or sold with  
the projector. Wall or shelf mounting should follow the  
manufacturer's instructions, and should use a mounting kit  
approved by the manufacturers.  
An appliance and cart combination should  
be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the appliance and cart  
combination to overturn.  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer that have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock, or injury to persons.  
Upon completion of any service or repairs to this projector, ask  
the service technician to perform routine safety checks to  
determine that the projector is in safe operating condition.  
Slots and openings in the back and bottom of the cabinet are  
provided for ventilation, to insure reliable operation of the  
equipment and to protect it from overheating.  
The openings should never be covered with cloth or other  
materials, and the bottom opening should not be blocked by  
placing the projector on a bed, sofa, rug, or other similar  
surface. This projector should never be placed near or over a  
radiator or heat register.  
This projector should not be placed in a built-in installation  
such as a book case unless proper ventilation is provided.  
Voor de klanten in Nederland  
Bij dit product zijn batterijen  
geleverd.  
Wanneer deze leeg zijn,  
moet u ze niet weggooien  
maar inleveren als KCA.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the projector.  
Do not install the projector near the ventilation duct of air-  
conditioning equipment.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPLIANCE  
Federal Communication Commission Notice  
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such  
changes or modifications should be made, you could be required to stop operation of the equipment.  
Model Numbers  
Trade Name  
: LC-X71/LC-X71L  
: EIKI  
Responsible party  
Address  
: EIKI International, Inc.  
: 30251 Esperanza Rancho Santa Margarita CA 92688-2132, U.S.A.  
Telephone No.  
: 800-242-3454 (949-457-0200)  
AC POWER CORD REQUIREMENT  
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada:  
AC Power Cord used in the United States and Canada is listed by the Underwriters  
Laboratories (UL) and certified by the Canadian Standard Association (CSA).  
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the  
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable  
to insert the plug into the outlet, contact your electrician.  
GROUND  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
FEATURES AND DESIGN  
6
COMPUTER INPUT  
24  
SELECTING INPUT SOURCE  
SELECTING COMPUTER SYSTEM  
24  
25  
PREPARATION  
7
PC ADJUSTMENT  
26  
26  
27  
AUTO PC ADJUSTMENT  
MANUAL PC ADJUSTMENT  
NAME OF EACH PART OF PROJECTOR  
7
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
POSITIONING PROJECTOR  
LENS INSTALLATION  
8
PICTURE IMAGE SELECT  
29  
8
IMAGE LEVEL SELECT  
29  
9
9
10  
10  
11  
PICTURE SCREEN ADJUSTMENT  
30  
30  
PICTURE SCREEN SELECT  
ADJUSTABLE FEET  
INSTALLING PROJECTOR IN PROPER POSITION  
MOVING PROJECTOR  
VIDEO INPUT  
31  
SELECTING INPUT SOURCE  
SELECTING VIDEO SYSTEM  
31  
32  
33  
33  
CONNECTING PROJECTOR  
12  
PICTURE IMAGE SELECT  
TERMINALS OF PROJECTOR  
CONNECTING TO COMPUTERS  
CONNECTING TO VIDEO EQUIPMENT  
12  
13  
14  
IMAGE LEVEL SELECT  
PICTURE SCREEN ADJUSTMENT  
34  
34  
PICTURE SCREEN SELECT  
PICTURE IMAGE  
35  
BEFORE OPERATION  
15  
PICTURE IMAGE ADJUSTMENTS  
35  
REMOTE CONTROL OPERATION  
LASER POINTER FUNCTION  
15  
15  
16  
REMOTE CONTROL BATTERIES INSTALLATION  
SETTING  
38  
TOP CONTROLS AND INDICATORS  
ON-SCREEN MENU  
17  
SETTING MENU  
38  
18  
18  
18  
19  
HOW TO OPERATE ON-SCREEN MENU  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
APPENDIX  
45  
WIRELESS MOUSE  
45  
MAINTENANCE  
46  
46  
47  
47  
BASIC OPERATION  
20  
WARNING TEMP. INDICATOR  
AIR FILTERS CARE AND CLEANING  
CLEANING PROJECTION LENS  
TURNING ON/OFF PROJECTOR  
TURNING ON THE PROJECTOR  
TURNING OFF THE PROJECTOR  
20  
20  
21  
LAMP REPLACEMENT  
48  
49  
LAMP REPLACE COUNTER  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
22  
22  
22  
22  
22  
23  
23  
23  
TROUBLESHOOTING  
50  
52  
54  
55  
MENU TREE  
FOCUS ADJUSTMENT  
LENS SHIFT ADJUSTMENT  
KEYSTONE ADJUSTMENT  
PICTURE FREEZE FUNCTION  
NO SHOW FUNCTION  
P-TIMER FUNCTION  
COMPATIBLE COMPUTER SPECIFICATIONS  
INDICATORS AND PROJECTOR CONDITION  
TECHNICAL SPECIFICATIONS  
CONFIGURATIONS OF TERMINALS  
OPTIONAL PARTS  
57  
58  
59  
59  
59  
60  
61  
LENS REPLACEMENT  
PJ LINK NOTICE  
PIN CODE NUMBER MEMO  
DIMENSIONS  
SOUND ADJUSTMENT  
23  
TRADEMARKS  
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.  
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.  
Windows and PowerPoint are registered trademarks of Microsoft Corporation.  
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES AND DESIGN  
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This  
projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD)  
technology.  
Compact Design  
Digital Zoom (for Computer)  
This projector is extremely compact in size and weight.  
It is designed to carry and work anywhere you wish to  
use.  
Digital Zoom function adjusts image size to approx. 1/4 ~  
49 times of an original image size, allowing you to focus  
on a crucial information at the presentation.  
Compatibility  
Keystone Correction  
This projector widely accepts various video and  
computer input signals such as:  
Positioning of the projector may result in distorted image  
being displayed in a trapezoid shape. Keystone function  
solves this problem by digitally altering the projection to  
produce undistorted images.  
Computers  
IBM-compatible or Macintosh computer up to 1600  
x 1200 resolution.  
Power Management  
6 Color Systems  
Power management function is provided to reduce power  
consumption when the projector is not in use.  
NTSC, PAL, SECAM, NTSC 4.43, PAL-M, or PAL-  
N color system can be connected.  
The Power management function operates to turn the  
projection lamp off when the projector detects a signal  
interruption or when no button is pressed for a certain  
period. The projection lamp is automatically turned on  
again when the projector detects a signal or any  
operation button is pressed.  
Component Video  
Component video signal, such as a DVD player  
output high definition TV signals including 480i,  
480p, 575i, 575p, 720p, 1035i, or 1080i, can be  
connected.  
S-Video  
This projector is shipped with this function ON.  
S-Video signal, such as a S-VHS VCR output  
signal, can be connected.  
Digital Visual Interface  
High Resolution Image  
This projector is equipped with the DVI 24-pin terminal  
for connecting DVI output from a computer.  
This projector provides 1024 x 768 dots resolution for  
computer input and 800 horizontal TV lines. Resolution  
from a computer between XGA (1024 x 768) and UXGA  
(1600 x 1200) is compressed into 1024 x 768 dots. This  
projector cannot display image of over 1600 x 1200 dots.  
When resolution of your computer is over 1600 x 1200,  
lower the resolution for a computer output.  
Laser Pointer Function  
Remote control supplied with this projector includes the  
Laser Pointer function. This function helps you to make a  
smart presentation on a projected screen.  
Wireless Mouse  
Multi-Scan System  
Remote control supplied with this projector has the  
Wireless Mouse function for a connected computer. This  
function enables you to operate both projector and  
computer with the remote control only.  
This projector has the Multi-Scan System to conform to  
almost all computer output signals quickly. There is no  
need for a troublesome manual adjustment of frequency  
and other settings.  
Multilanguage Menu Display  
One-Touch Auto PC Adjustment  
Operation menu is available in 12 languages: English,  
German, French, Italian, Spanish, Portuguese, Dutch,  
Swedish, Russian, Chinese, Korean, or Japanese.  
Incoming computer video signals are recognized and  
best adjustment is automatically set by the Auto PC  
Adjustment function. No complicated setup is necessary  
and the projection is always precise.  
Pj-to NetDirector (Optional)  
Pj-to NetDirector enables the projector to display the  
image of the computer screen and the image data stored  
in the computer via a network. The projector can also be  
controlled and maintained through a web browser.  
Motor-driven Lens Shift  
Projection lens can be moved up and down with the  
motor-driven lens shift function. This function makes it  
easy to provide projected image where you want.  
Zoom and focus can also be adjusted with a motor-  
driven operation.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
NAME OF EACH PART OF PROJECTOR  
SPEAKERS  
TOP CONTROLS  
AND INDICATORS  
FRONT OF CABINET  
PROJECTION LENS  
Optional: LC-X71L  
CAUTION  
Do not turn on the projector with  
the lens cap attached. High  
temperature from light beam  
may damage the lens cap and  
result in fire hazard.  
AIR INTAKE  
VENT  
LENS CAP  
INFRARED  
REMOTE RECEIVER  
Optional: LC-X71L  
BACK OF CABINET  
POWER CORD  
CONNECTOR  
TERMINALS  
AND CONNECTORS  
INFRARED  
REMOTE RECEIVER  
EXHAUST VENT  
HOT AIR EXHAUSTED !  
Air blown from the exhaust vent is hot.  
When using or installing the projector, the  
following precautions should be taken.  
Do not put a flammable object near this vent.  
Keep the rear grills at least 3.3’ (1 m) away  
from any object, especially from heat-  
sensitive objects.  
Do not touch this area, especially screws  
and metallic parts. This area will become hot  
when the projector is in use.  
CARRYING  
HANDLE  
LAMP COVER  
This projector detects internal temperature  
and automatically controls operating power  
of the cooling fans.  
When attaching the Pj-to NetDirector  
(optional) to the projector, remove these  
parts. Refer to the owner’s manual of the  
optional Pj-to NetDirector.  
BOTTOM OF CABINET  
AIR INTAKE VENTS  
This projector is equipped with the cooling fans for protecting from  
overheating. Pay attention to the following matters to ensure  
proper ventilation and avoid a possible risk of fire and malfunction.  
Do not cover the vent slots.  
Keep this side clear of any objects. Obstructions may block  
cooling air.  
ADJUSTABLE FEET  
AND  
FEET LOCK LATCHES  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
This projector uses nominal input voltages of 100-120 V or 200-  
240 V AC and it automatically selects correct input voltage. It is  
designed to work with single-phase power systems having a  
grounded neutral conductor. To reduce risk of electrical shock, do  
not plug into any other type of power system.  
If you are not sure of the type of power being supplied, consult  
your authorized dealer or service station.  
Connect the projector with all peripheral equipment before turning  
it on. (See pages 12-14 for connection.)  
CAUTION  
For safety, unplug the AC power cord when the projector is not  
in use. When the projector is connected to an outlet with AC  
power cord, an appliance is in stand-by mode and consumes a  
little electric power.  
Connect AC power cord (supplied) to the  
projector.  
The AC outlet must be near this equipment and  
must be easily accessible.  
NOTE ON POWER CORD  
AC power cord must meet the requirements of the country where you use the projector.  
Confirm the AC plug type with the chart below and a proper AC power cord must be used.  
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.  
Projector side  
AC Outlet side  
For the U.S.A. and Canada  
For Continental Europe  
Ground  
To POWER CORD  
CONNECTOR on your  
projector.  
To the AC Outlet.  
(120 V AC)  
To the AC Outlet.  
(200 - 240 V AC)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
POSITIONING PROJECTOR  
NOTE: The figures below are only for the Model LC-X71.  
A ROOM LIGHT  
The projection lens is not provided with the Model LC-X71L.  
Brightness in a room has a great  
influence on the picture quality. It is  
recommended to limit ambient lighting  
in order to provide the best image.  
This projector is designed to project on a flat projection surface.  
Projector can be focused from 4.6’ (1.4 m) ~ 48.3’ (14.7 m).  
Refer to the figure below to adjust the screen size.  
47.3’(14.4m)  
35.4’(10.8m)  
400”  
Max. Zoom  
23.6’(7.2m)  
11.8’(3.6m)  
300”  
231”  
308”  
200”  
4.6’(1.4m)  
Min. Zoom  
100”  
77”  
154”  
40”  
31”  
Max. Zoom  
Min. Zoom  
40”  
31”  
100”  
77”  
150”  
115”  
200”  
154”  
250”  
192”  
300”  
231”  
400”  
308”  
Screen  
Size  
4.6’ (1.4 m)  
11.8’ (3.6 m) 17.7’ (5.4 m)  
23.6’ (7.2m)  
29.5’ (9.0 m) 35.4’ (10.8 m) 47.3’ (14.4 m)  
Distance  
LENS SHIFT ADJUSTMENT  
Projection lens can be moved up and down with the motor-driven Lens shift function. This function makes it easy  
to provide projected image where you want. The U/D ratio can be adjusted 10:0 ~ 1:1 (see Figure below). See  
page 22 for operation.  
Highest (10 : 0)  
Lowest (1 : 1)  
LENS INSTALLATION  
Before setting up the projector, install a projection lens on  
the projector.  
1. Before installation, check the area where the projector is  
used and prepare a suitable lens. For the specifications of  
a projection lens, contact sales dealer where you  
purchased the projector.  
COVER CAP  
2. For installation, refer to the installation manual of the  
optional lens.  
NOTE:  
• When installing the lens, remove the cover cap of the projector.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
ADJUSTABLE FEET  
Projection angle can be adjusted up to 10.5 degrees with the  
ADJUSTABLE FEET.  
Lift the front of the projector and pull the FEET LOCK  
LATCHES in each side of the projector.  
1
Release the FEET LOCK LATCHES to lock the  
ADJUSTABLE FEET and rotate the ADJUSTABLE FEET to a  
proper height, and tilt.  
2
To retract the ADJUSTABLE FEET, lift the front of the  
projector and pull and undo the FEET LOCK LATCHES.  
3
Keystone distortion of the projected image can be adjusted by  
the Menu Operation. (See pages 22 and 38.)  
ADJUSTABLE FEET  
FEET LOCK  
LATCHES  
INSTALLING PROJECTOR IN PROPER POSITION  
Install the projector properly. Improper installation may reduce the lamp life and cause a fire hazard.  
10˚  
Do not tilt the projector more than 10 degrees from side to side.  
10˚  
Do not put the projector on either side to project an image.  
NO SIDEWAYS  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
MOVING PROJECTOR  
Use the Carrying Handle when moving the projector.  
Replace the lens cap and retract the ADJUSTABLE FEET  
when moving the projector to prevent damages to the lens  
and cabinet.  
When this projector is not in use for an extended period, put  
it into a suitable case (not supplied with this projector).  
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR  
Do not drop or bump the projector, otherwise damages or malfunctions may result.  
When carrying the projector, use a suitable carrying case.  
Do not transport the projector by courier or any other transport service in an unsuitable transport case.  
This may cause damage to the projector. To transport the projector by courier or any other transport  
service, consult your dealer for the best way.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
TERMINALS OF PROJECTOR  
This projector has input and output terminals on its back for connecting computers and video equipment. Refer  
to the figures on pages 12 to 14 and connect properly.  
COMPUTER INPUT/MONITOR  
OUTPUT TERMINAL (ANALOG)  
COMPUTER INPUT  
TERMINAL (DIGITAL)  
COMPUTER AUDIO  
INPUT 2 JACK  
COMPUTER AUDIO INPUT 1/  
AUDIO MONITOR OUTPUT  
JACK  
This terminal is switchable and  
can be used as Computer Input  
or Monitor Output. Set up the  
terminal as either Computer Input  
or Monitor Output properly before  
using this terminal.  
(See pages 13-14 and 24.)  
Note: This terminal outputs from the 5  
BNC type computer input on INPUT 2  
jacks only.  
Connect a computer output Connect an audio  
(Digital DVI-D type) to this output (stereo) from a  
terminal.  
The HD (HDCP Compatible) (See page 13.)  
signal can also be connected.  
(See page 13.)  
This terminal is switchable and  
can be used as Computer  
Audio Input 1 or Audio Monitor  
Output (variable).  
Set up the terminal as either  
Computer Audio Input 1 or  
Audio Monitor Output properly  
before using this terminal.  
(See pages 13 and 24.)  
computer to this jack.  
R/C JACK  
When using the Wired/  
Wireless remote control as  
wired, connect the Wired  
remote control to this jack with  
USB CONNECTOR (Series B)  
When controlling a computer  
with the remote control of this  
projector, connect USB terminal  
of your personal computer to  
this terminal. (See page 13.)  
a
remote control cable  
(optional).  
CONTROL PORT CONNECTOR  
When controlling a computer  
with the remote control of this  
projector, connect the mouse  
port of your personal computer  
to this connector. (See page  
13.)  
RESET BUTTON  
This projector uses  
a
micro  
processor to control the unit, and  
only occasionally, this micro  
processor may malfunction and  
need to be reset. This can be done  
by pressing the RESET button with  
a pen, which will shut down and  
restart the unit. Do not use the  
RESET function excessively.  
VIDEO INPUT JACKS  
AUDIO INPUT JACKS  
S-VIDEO INPUT JACK  
Connect composite video Connect an audio output Connect S-VIDEO  
output from video equipment from video equipment to output from video  
to VIDEO/Y jack or connect these jacks. (See page equipment to this  
5 BNC INPUT JACKS  
Connect component video  
output (Y, Cb, Cr or Y, Pb, Pr)  
from video equipment to  
VIDEO/Y, Cb/Pb and Cr/Pr  
jacks or connect computer  
output {5 BNC Type (Green,  
Blue, Red, Horiz. Sync, and  
Vert. Sync.)} from computer to  
G, B, R, H/V, and V jacks.  
(See pages 13 and 14.)  
component video outputs to 14.)  
VIDEO/Y, Cb/Pb and Cr/Pr  
jacks. (See page 14.)  
jack. (See page 14.)  
EXTERNAL SPEAKER TERMINALS  
Connect external speakers to  
these terminals. (See pages 13  
and 14.)  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO COMPUTERS  
Cables used for connection (= Cables or adapters not supplied with this projector.)  
• VGA Cable (HDB 15 pin)  
• DVI-Digital Cable (for Single Link T.M.D.S.) ✽  
• BNC Cable ✽  
• Control Cable for PS2 Port , or ADB Port ✽  
• USB Cable  
• Audio Cables (Mini Plug (stereo) x 2) ✽  
• Control Cable for Serial Port  
IBM-compatible computer or Macintosh computer (VGA/SVGA/XGA/SXGA/SXGA+/WXGA/UXGA )  
Desktop type  
Laptop type  
Monitor Output  
or  
Monitor Output  
Monitor Output USB port  
Audio Output Serial port  
PS/2 port  
ADB port  
Monitor Input  
Control Cable  
for Serial Port  
Control Cable Control Cable  
for PS/2 Port for ADB Port ✽  
USB  
Cable  
Audio  
Cable ✽  
(stereo)  
DVI  
Cable ✽  
VGA Cable  
Terminal  
Terminal  
Terminal  
BNC  
Cable ✽  
COMPUTER  
AUDIO IN 1 or 2  
Use one of these Control  
Cables corresponding with  
terminal of your computer.  
USB  
COMPUTER IN ANALOG  
COMPUTER IN DIGITAL  
CONTROL  
PORT  
INPUT 1  
DIGITADVI-D)  
ANALOIN/OUT  
R/C JACK  
CONTRL PORT  
RESET  
USB  
AUDIO 1  
IN/OUT  
AUDIO 2  
NOTE:  
This terminal is switchable.  
Set up the terminal as either  
Computer input or Monitor  
output before using this  
terminal.(See page 24.)  
AUDIO OUT  
G
B
R
H/V  
V
External Speaker Terminals  
(Front of the projector)  
VIDEO/Y Cb/Pb  
Cr/Pr  
INPUT 2  
S–VIDEO  
VIDEO/Y Cb/Pb Cr/Pr  
R–AUDIO–L  
NOTE:  
This terminal is switchable.  
Set up the terminal as  
either Computer Audio  
Input 1 or Audio Monitor  
Output (variable) before  
using this terminal. (See  
page 24.)  
Audio Cable  
(stereo) ✽  
(
)
MONO  
INPUT 3  
Terminals  
of the Projector  
Audio Input  
External Audio Equipment  
NOTE:  
Audio Speakers  
(stereo)  
Unplug the power cords of both the projector and  
external equipment from the AC outlet before  
connecting cables. Turn a projector and peripheral  
equipment on before computer is switched on.  
Audio Amplifier  
Audio Speakers  
(stereo)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO VIDEO EQUIPMENT  
Cables used for connection (= Cables not supplied with this projector.)  
• Video Cable (RCA x 1 or RCA x 3) ✽  
• BNC Cable ✽  
• Audio Cable {Mini Plug (stereo)} ✽  
• Scart Cable ✽  
• S-VIDEO Cable ✽  
• Audio Cable (RCA x 2) ✽  
Video Source (Example)  
Video Cassette Recorder  
Component video output equipment.  
(such as DVD players or high-definition TV sources.)  
Video Disc Player  
Component Video  
Output  
(Y, Cb/Pb, Cr/Pr)  
Component Video  
Output  
(Y, Cb/Pb, Cr/Pr)  
RGB Scart  
21-pin Output Video Output  
Composite  
Composite  
Video Output  
S-VIDEO  
Output  
Audio Output Audio Output  
Video Cables  
(RCA x 1 or  
RCA x 3) ✽  
Scart Cable ✽  
Audio  
Audio Cable  
S-VIDEO  
Cable ✽  
(stereo)  
(RCA x 2) ✽  
Cable ✽  
BNC Cable ✽  
Y - Cb/Pb - Cr/Pr  
Y - Cb/Pb - Cr/Pr  
VIDEO  
VIDEO  
AUDIO IN  
AUDIO IN  
S-VIDEO  
COMPUTER IN ANALOG  
AUDIO OUT  
Audio Cable  
(stereo) ✽  
External Speaker Terminals  
(Front of the projector)  
NOTE:  
This terminal is switchable.  
Set up the terminal as either  
Computer input or Monitor  
output before using this  
terminal.(See page 24.)  
Terminals  
of the Projector  
Audio Input  
External Audio Equipment  
Audio Speakers  
(stereo)  
Audio Amplifier  
NOTE:  
Unplug the power cords of both the projector  
and external equipment from the AC outlet  
before connecting cables.  
Audio Speakers (stereo)  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
REMOTE CONTROL OPERATION  
LASER POINTER  
(DRAG ON) INDICATOR  
Left Side  
POWER ON-OFF BUTTON  
Used to turn the projector on  
or off. (p.20, 21)  
Lights red while the laser  
beam is emitted from the  
Laser Light Window.  
AUTO PC ON-OFF  
Lights green when dragged  
to the “ON” position. (p.45)  
D.ZOOM FREEZE NO SHOW  
AUTO PC ADJ. BUTTON  
MUTE  
Use to operate the AUTO PC  
Adjustment function. (p.26)  
IMAGE  
MUTE BUTTON  
Used to mute the sound.  
(p.23)  
VOLUME  
-
VOLUME+  
SELECT  
IMAGE BUTTON  
Used to select the image  
level. (p.29, 33)  
MENU  
KEYSTONE  
DRAG ON/OFF BUTTON  
Used to select the DRAG  
ON/OFF position. (p.45)  
ALL OFF SWITCH  
When using the remote control, turn  
this switch to “ON.” And turn it to  
“ALL OFF” when it is not in use.  
KEYSTONE BUTTON  
Used to correct keystone  
distortion. (p.22, 38)  
LEFT CLICK BUTTON  
INSIDE THE BATTERY  
COMPARTMENT BOX  
Used as a PC mouse in  
Wireless Mouse Operation.  
Press this button and the  
mouse pointer button to drag  
the selected screen object.  
(p.45)  
MOUSE POINTER  
Used as a PC mouse in  
Wireless Mouse Operation.  
(p.45)  
This Remote Control provides the DIP  
switches into the battery compartment  
box.  
Slide the SW4 (LASER ON/OFF  
switch) to the “OFF” position. The  
Laser Pointer function is not operated.  
Set the Switches 1-3 as shown in table  
below depending on the Code No. that  
you want to select as the remote  
control code. (See page 41.)  
LASER  
RIGHT CLICK BUTTON  
LASER BUTTON  
Used as a PC mouse in  
Wireless Mouse Operation.  
(p.45)  
P-TIMER INPUT 1  
Used to operate the Laser  
Pointer function. The laser  
beam is emitted when  
pressing this button for one  
minute.  
When using the Laser Pointer  
for more than one minute,  
release this button and press  
it again.  
ZOOM COLOR.M INPUT 2  
INPUT 3  
LENS SHIFT BUTTON  
Used to select the Lens Shift  
function. (p.22)  
FOCUS LENS  
DIP SWITCH SETTING  
SW4 ........ LASER ON/OFF  
SW1 SW2 SW3 Code No.  
WIRED REMOTE JACK  
ON  
ON  
ON  
ON  
ON  
OFF ON  
ON  
Code 1  
Code 2  
Code 3  
When using as  
a
Wired  
OFF  
Remote Control, connect a  
remote control cable (optional)  
to this jack.  
FOCUS BUTTON  
Used to adjust focus. (p.22)  
ON  
OFF OFF  
Code 4  
Code 5  
Code 6  
Code 7  
Code 8  
OFF ON  
OFF ON  
ON  
OFF  
Battery installation is required  
OFF OFF ON  
OFF OFF OFF  
when using as  
Remote Control.  
a
Wired  
LASER POINTER FUNCTION  
This remote control emits laser beam from the Laser Light Window when used as a Laser Pointer. When the  
LASER button is pressed, the laser light goes on. When the LASER button is being pressed for more than one  
minute or when it is released, the light goes off. The LASER POINTER INDICATOR lights RED and the LASER  
is emitted with RED light to indicate the laser beam is being emitted.  
The Laser emitted is the Cass II laser. Do not look into the Laser Light Window or shine laser beam onto yourself  
or other people. The three marks shown below are caution labels for the laser beam.  
CAUTION: Use of controls, adjustments, or performance of procedures other than those specified herein may  
result in hazardous radiation exposure.  
These caution labels are put on the remote control.  
LASER POINTER INDICATOR  
LASER LIGHT WINDOW  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
D.ZOOM BUTTON  
Operating Range  
Used to select the  
DIGITAL ZOOM +/– mode  
and resize the image.  
(p.30)  
Point the remote control toward  
the projector (a Receiver  
Window) when pressing any  
button. Maximum operating  
range for the remote control is  
about 16.4’ (5 m) and 60° in front  
and rear of the projector.  
NO SHOW BUTTON  
Used to turn the picture  
into a black image. (p.23)  
AUTO PC ON-OFF  
D.ZOOM FREEZE NO SHOW  
SELECT BUTTON  
MUTE  
IMAGE  
FREEZE BUTTON  
Used to freeze the picture.  
(p.23)  
Used to execute the  
selected item, or expand/  
compress the image in the  
DIGITAL ZOOM +/- mode.  
(p.30)  
VOLUME  
-
VOLUME+  
SELECT  
MENU  
KEYSTONE  
POINT (VOLUME +/-)  
BUTTONS  
Used to select an item or  
adjust a value in On-Screen  
Menu. They are also used to  
pan the image in the  
DIGITAL ZOOM +/- mode.  
(p.30)  
60°  
MENU BUTTON  
Used to select the MENU  
Operation. (p.18, 19)  
The POINT LEFT/RIGHT  
buttons are also used as  
VOLUME +/- buttons. (p.23)  
16.4’  
(5 m)  
P-TIMER BUTTON  
Used to operate the P-  
TIMER function. (p.23)  
INPUT 1 BUTTON  
Used to select an input  
source (INPUT 1). (p.24)  
LASER  
P-TIMER INPUT 1  
ZOOM COLOR.M INPUT 2  
INPUT 3  
INPUT 2 BUTTON  
ZOOM BUTTON  
Used to adjust zoom.  
(p.22)  
Used to select an input  
source (INPUT 2).  
(p.25, 31)  
FOCUS LENS  
16.4’  
(5 m)  
INPUT 3 BUTTON  
Used to select an input  
source (INPUT 3). (p.31)  
COLOR MANAGEMENT  
BUTTON  
Used to operate the Color  
management function.  
(p.35-36)  
60°  
REMOTE CONTROL BATTERIES INSTALLATION  
Open the battery  
compartment lid.  
Install new batteries into  
the compartment.  
Replace the compartment lid.  
1
2
3
Two AA size batteries  
Press the lid downward  
and slide it.  
For correct polarity (+ and  
–), be sure battery terminals  
are in contact with pins in  
the compartment.  
To insure safe operation, please observe following precautions:  
Use two (2) AA or LR6 type alkaline batteries.  
Always replace batteries in sets.  
Do not use a new battery with an used battery.  
Avoid contact with water or liquid.  
Do not expose the remote control to moisture, or heat.  
Do not drop the remote control.  
If a battery has leaked on the remote control, carefully wipe the case clean and install new batteries.  
Danger of explosion if battery is incorrectly replaced.  
Dispose of used batteries according to batteries manufacturers instructions and local rules.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
TOP CONTROLS AND INDICATORS  
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.  
TOP CONTROLS AND  
INDICATORS  
EXT. SP SWITCH  
Used to select speakers.  
(Internal or External)  
MENU BUTTON  
SELECT BUTTON  
POWER ON–OFF BUTTON  
INPUT BUTTON  
Used to open or  
close the On-Screen  
Menu. (p.18, 19)  
Used to execute the  
selected item. It is also  
used to expand/compress  
the image in the DIGITAL  
ZOOM mode. (p.30)  
Used to turn the projector Used to select an input  
on or off. (p.20, 21)  
source. (p.24, 31)  
ZOOM BUTTON  
AUTO PC ADJ. BUTTON  
Used to adjust zoom.  
(p.22)  
Used to operate the Auto  
PC Adjustment function.  
(p.26)  
FOCUS BUTTON  
Used to adjust focus.  
(p.22)  
IMAGE BUTTON  
Used to select the  
image level. (p.29, 33)  
LENS SHIFT BUTTON  
Used to select the Lens  
Shift function. (p.22)  
KEYSTONE BUTTON  
Used to correct  
keystone distortion.  
(p.21, 37)  
LAMP REPLACE INDICATOR  
Turns to yellow when the  
projection lamp reaches its  
end of life.  
Blinks yellow when the  
lamp cannot light up. (p.48,  
55-56)  
LAMP INDICATOR  
Becomes dim when the  
projector is turned on.  
And it becomes bright  
when the projector is in  
stand-by mode. (p.20,  
21, 55-56)  
READY INDICATOR  
POINT (VOLUME + / – ) BUTTONS  
WARNING TEMP. INDICATOR  
Lights green when the  
projector is ready to be  
turned on. And it blinks  
green in the Power  
management mode.  
Used to select an item or adjust a Blinks red when the internal  
value in On-Screen Menu. They are temperature of the projector  
also used to pan the image in the is too high. (p.46, 55-56)  
DIGITAL ZOOM +/– mode. (p.30)  
The POINT LEFT/RIGHT buttons are  
also used as VOLUME +/– buttons.  
(p.40, 46, 55-56)  
(p.23)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
REMOTE CONTROL  
You can control and adjust this projector with the On-  
Screen Menu. Refer to the relevant pages to operate  
each adjustment.  
AUTO PC ON-OFF  
1. DISPLAY MENU  
POINT BUTTONS  
D.ZOOM FREEZE NO SHOW  
Press the MENU button to display the On-Screen Menu.  
Used to move the  
Pointer UP/DOWN/  
RIGHT/LEFT.  
MUTE  
IMAGE  
2. MOVING POINTER  
VOLUME  
-
VOLUME+  
SELECT  
Move the pointer (see below) or adjust a value of an item by  
pressing the POINT buttons on the top control or on the remote  
control.  
MENU  
KEYSTONE  
The Pointer is an icon in the On-Screen Menu for selecting  
an item. See figures in “FLOW OF ON-SCREEN MENU  
OPERATION” below.  
MENU BUTTON  
SELECT BUTTON  
Used to select the item.  
TOP CONTROL  
3. SELECT ITEMS  
Select an item or set the selected function by pressing the  
SELECT button.  
POINT BUTTONS  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
MENU BUTTON  
SELECT BUTTON  
Used to select the item.  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
MENU ICON  
Display ON-SCREEN MENU  
Press the MENU button to display the On-Screen Menu  
(a MENU BAR). A red frame is a POINTER.  
1
POINTER  
(red frame)  
Select Menu to be adjusted  
POINTER (red frame)  
Press the POINT UP/DOWN  
buttons to move the POINTER.  
Move the POINTER (red frame) to a MENU ICON that  
you want to select by pressing the POINT RIGHT/LEFT  
buttons.  
2
ITEM  
Control or adjust items through ON-SCREEN MENU  
SELECT  
BUTTON  
Press the POINT UP/DOWN buttons and move the  
3
POINTER (red frame or red arrow) to an ITEM that you  
want to adjust, and then press the SELECT button to  
show the ITEM DATA.  
Adjust the ITEM DATA by pressing the POINT  
RIGHT/LEFT buttons.  
Refer to the relevant pages for details of respective  
adjustments.  
4
ITEM DATA  
Press the POINT LEFT/RIGHT  
buttons to adjust a value or set a  
function.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
MENU BAR  
FOR PC SOURCE  
GUIDE WINDOW  
Press the MENU button when connecting to the PC input source.  
IMAGE SELECT MENU  
SCREEN MENU  
SETTING MENU  
PC SYSTEM MENU  
Used to select an  
image level among  
Standard, Real, and  
Image 1 ~ 10.  
Used to adjust the  
size of an image.  
[Normal/True/Wide/ or reset the Lamp  
Full/Digital zoom replacement counter.  
+/–] (See page 30.) (See pages 38-44.)  
Used to change  
settings of the projector  
Used to select a  
computer system.  
(See pages 24  
and 25.)  
Shows the  
selected item of  
On-Screen Menu.  
(See page 29.)  
SOUND MENU  
PC ADJUST MENU  
IMAGE ADJUST MENU  
INPUT MENU  
Used to adjust  
the volume or  
mute the sound.  
(See page 23.)  
Used to adjust  
the parameters  
to match with the  
input signal  
format. (See  
pages 26-28.)  
Used to adjust the computer  
image. [Contrast/  
Used to select an  
input source (Input 1,  
Input 2, or Input 3).  
(See page 24.)  
Brightness/Color/Tint/Color  
management/Auto picture  
control/Color temp./White  
balance (R/G/B)/Sharpness/  
Gamma/Noise reduction/  
Progressive] (See pages  
35-37.)  
FOR VIDEO SOURCE  
Press the MENU button when connecting to the VIDEO input source.  
INPUT MENU  
IMAGE SELECT MENU  
Used to select an  
input source  
(Input 1, Input 2,  
or Input 3). (See  
page 31.)  
Used to select an  
image level among  
Standard, Cinema,  
and Image 1 ~ 10.  
(See page 33.)  
SCREEN MENU  
Used to adjust the size  
of image to Normal or  
Wide. (See page 34.)  
AV SYSTEM MENU  
IMAGE ADJUST MENU  
Same function as  
menu for PC source.  
Same function as  
menu for PC source.  
Used to select the  
system of selected  
video source. (See  
page 32.)  
Used to adjust the picture  
image. [Contrast/Brightness/  
Color/Tint/Color management/  
Auto picture control/Color  
temp./White balance (R/G/B)/  
Sharpness/Gamma/Noise  
reduction/Progressive] (See  
pages 35-37.)  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
TURNING ON / OFF PROJECTOR  
TURNING ON THE PROJECTOR  
Complete peripheral connections (with a computer, VCR, etc.)  
before turning on the projector.  
1
2
16  
Connect the projector’s AC power cord into an AC outlet. The  
LAMP indicator lights RED, and the READY indicator lights  
GREEN.  
Press the POWER ON-OFF button on the top control or on  
the remote control. The LAMP indicator dims, and the cooling  
fans start to operate. The preparation display appears on the  
screen and the countdown starts.  
3
4
The preparation display disappears after 30 seconds.  
Selected Input Source and Lamp control  
After the countdown, the input source that was selected the  
last time and the Lamp control status icon (see page 41)  
appear on the screen.  
Lamp control status  
If the projector is locked with a PIN code, a PIN code Input  
Dialog Box appears. Enter a PIN code as instructed below.  
PIN code Input Dialog Box  
To Enter a PIN code  
Select a number by pressing the POINT LEFT/RIGHT button and  
fix the number with the SELECT button. The number changes to  
.” If you fixed a wrong number, move the pointer to “Set” or  
“Clear” once by pressing the POINT DOWN button, then return to  
“PIN code.” Enter the correct number.  
Pointer  
Repeat this step to complete entering a four-digit number.  
When the four-digit number is fixed, the pointer automatically  
moves to “Set.” Press the SELECT button so that you can start to  
operate the projector.  
If you entered a wrong PIN code, “PIN code” and the number  
(✳✳✳✳) turn red and disappear. Enter a PIN code all over again.  
After the OK icon  
disappears, you can  
operate the projector.  
What is PIN code?  
PIN (Personal Identification Number) code is a security code that  
allows the person who knows it to operate the projector. Setting a  
PIN code prevents unauthorized use of the projector.  
A PIN code consists of a four-digit number. Refer to the PIN code  
lock function in SETTING Menu on page 43 for locking operation  
of the projector with your PIN code.  
CAUTION ON HANDLING PIN CODE  
If you forget your PIN code, the projector can no  
longer be started. Take special care in setting a new  
PIN code; write down the number in a column on  
page 60 of this manual and keep it at hand. Should  
the PIN code be missing or forgotten, consult your  
dealer or service center.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
TURNING OFF THE PROJECTOR  
Press the POWER ON-OFF button on the top control or on  
the remote control, and “Power off?” appears on the screen.  
1
2
Press the POWER ON-OFF button again to turn off the  
projector. The LAMP Indicator lights bright and the READY  
Indicator turns off. After the projector is turned off, the cooling  
fans operate (for 90 seconds). During this “cooling down”  
period, the projector cannot be turned on.  
“Power off?” disappears after 4 seconds.  
When the projector has cooled down, the READY Indicator  
lights GREEN again and you can turn projector on. After  
cooling down completely, unplug the AC power cord.  
3
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU  
TURN THE PROJECTOR ON, WAIT AT LEAST FIVE  
MINUTES BEFORE TURNING IT OFF.  
DO NOT UNPLUG THE AC POWER CORD WHILE  
COOLING FANS ARE RUNNING OR BEFORE THE  
READY INDICATOR LIGHTS GREEN AGAIN.  
OTHERWISE IT WILL RESULT IN SHORTENING THE  
LAMP LIFE.  
Note:  
• The projector cannot be turned on during the cooling period with the READY  
indicator turned off. You can turn it on again after the READY indicator becomes  
GREEN again.  
• When the On start function is “On,” this projector is turned on automatically by  
connecting the AC power cord to an AC outlet. (See page 41 for the On start  
function.)  
• Continuous use may result in shortening the lamp life. Turn off the projector  
and rest it for about an hour in every 24 hours.  
• The running speed of cooling fans is changed according to the temperature  
inside the projector.  
• If the WARNING TEMP indicator blinks RED, see “WARNING TEMP  
INDICATOR” on page 46.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
Press the ZOOM button on the top control or ZOOM /▼  
buttons on the remote control. “Zoom” appears on the screen.  
1
2
Press the ZOOM button or POINT UP button to make the  
image larger, and press the ZOOM button or POINT DOWN  
button to make the image smaller.  
“Zoom” disappears after 4 seconds.  
FOCUS ADJUSTMENT  
Press the FOCUS button on the top control or FOCUS /▼  
buttons on the remote control. “Focus” appears on the screen.  
1
2
Adjust the focus of image by pressing the FOCUS /buttons  
or POINT UP/DOWN buttons.  
“Focus” disappears after 4 seconds.  
NOTE:  
• Focus adjustment may not function properly if the image is corrected by the  
Keystone function.  
LENS SHIFT ADJUSTMENT  
Press the LENS SHIFT button on the top control or LENS SHIFT  
/buttons on the remote control. “Lens shift” appears on the  
screen.  
1
2
Press the POINT UP button or LENS SHIFT button to move  
the image up, press the POINT DOWN or LENS SHIFT button  
to move the image down.  
“Lens shift” disappears after 4 seconds.  
KEYSTONE CORRECTION  
If a projected picture has keystone distortion, correct the image with the Keystone function.  
Press the KEYSTONE button on the remote control or select  
Keystone in the SETTING Menu. (See page 38.) The Keystone  
dialog box appears.  
1
Correct keystone distortion by pressing the POINT  
UP/DOWN/LEFT/RIGHT buttons. Press the POINT UP button to  
reduce the upper part of the image; press the POINT DOWN  
button to reduce the lower part. Press the POINT LEFT button to  
reduce the left part; press the POINT RIGHT button to reduce  
the right part.  
2
• Arrows are white when no correction.  
• Arrow(s) in the corrected direction turn(s) red.  
• Arrow(s) disappear(s) at the maximum correction.  
• If you press the KEYSTONE button on the remote  
control once more while the keystone dialog box is  
being displayed, the Keystone function is canceled.  
• “Keystone” disappears after 10 seconds.  
Reduce the upper width  
with POINT UP button.  
Reduce the lower width  
with POINT DOWN button.  
Reduce the left part with  
POINT LEFT button.  
Reduce the right part with  
POINT RIGHT button.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
PICTURE FREEZE FUNCTION  
Press the FREEZE button on the remote control to freeze the picture on the screen. To cancel the FREEZE  
function, press the FREEZE button again or press any other button.  
NO SHOW FUNCTION  
Press the NO SHOW button on the remote control to black out  
the image. To restore to normal, press the NO SHOW button  
again or press any other button.  
“No show” disappears after 4 seconds.  
P-TIMER FUNCTION  
Press the P-TIMER button on the remote control. A Timer  
display “00 : 00” appears on the screen and starts to count time  
(00 : 00 ~ 59 : 59).  
To stop the P-TIMER, press the P-TIMER button. Press the P-  
TIMER button again to cancel the P-TIMER function.  
SOUND ADJUSTMENT  
Indicates an approximate level of the volume.  
DIRECT OPERATION  
Volume  
Press the VOLUME (+/–) buttons on the top control or on the remote  
control to adjust the volume. A Volume dialog box appears on the  
screen for a few seconds.  
Press the VOLUME (+) button to increase the volume; press the  
VOLUME (–) button to decrease the volume.  
Mute  
Press the MUTE button to set  
the Mute function On or Off.  
Press the MUTE button on the remote control to turn off the sound. To  
restore the sound to its previous level, press the MUTE button again  
or press the Volume (+/–) buttons.  
The Volume dialog box disappears after 4 seconds.  
MENU OPERATION  
Press the MENU button to display the On-Screen Menu. Press  
the POINT LEFT/RIGHT buttons to move the red frame pointer  
to the SOUND Menu icon.  
1
SOUND MENU  
Press the POINT UP/DOWN buttons to move the red frame  
pointer to the desired item, and then press the SELECT button.  
2
SOUND Menu icon  
Indicates an approximate  
level of the volume.  
Volume  
To increase the volume, press the POINT RIGHT button; to decrease  
the volume, press the POINT LEFT button.  
Closes the SOUND Menu  
Built-in SP.  
Press the POINT LEFT/RIGHT buttons to switch the built-in speaker  
On or Off.  
Mute  
Press the POINT LEFT/RIGHT buttons to turn off the sound. The  
Dialog box display is changed to “On” and the sound is turned off. To  
restore the sound to its previous level, press the POINT LEFT/RIGHT  
buttons again.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
SELECTING INPUT SOURCE  
DIRECT OPERATION  
INPUT button  
Input 1  
Select an INPUT source by pressing the INPUT button on  
the top control or the INPUT 1, INPUT 2, or INPUT 3 buttons  
on the remote control.  
If the projector cannot reproduce proper image, select a  
correct input source by MENU OPERATION (see below).  
Input 2  
Input 3  
NOTE:  
• Input 1 terminal is switchable and can be used as Computer Input or Monitor  
Output.  
Input 1 is not displayed when the Input 1 is used as  
Monitor out.  
MENU OPERATION  
WHEN SELECTING INPUT 1 (COMPUTER INPUT TERMINALS )  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the INPUT Menu icon.  
1
2
3
INPUT MENU  
Press the POINT UP/DOWN buttons to move the red arrow  
pointer to Input 1 and then press the SELECT button. A  
Source Select Menu appears.  
INPUT Menu icon  
Move the pointer (red arrow) to Input 1  
and press the SELECT button.  
Move the pointer to a source that you want to select and then  
press the SELECT button.  
RGB (PC analog)  
Input 1  
When your computer is connected to the INPUT 1 (ANALOG)  
terminal, select RGB (PC analog).  
Source Select Menu  
Move the pointer (red arrow)  
to a source and press the  
SELECT button.  
RGB (Scart)  
When scart video equipment is connected to the INPUT 1  
(ANALOG) terminal, select RGB (Scart).  
RGB (PC digital)  
When your computer is connected to INPUT 1 (DIGITAL)  
terminal, select RGB (PC digital).  
RGB (AV HDCP)  
If a HDCP-compatible signal source is connected to the  
INPUT 1 (DIGITAL) terminal, select RGB (AV HDCP).  
Monitor out  
If the INPUT 1 ANALOG terminal is being used as a  
MONITOR OUT terminal, select Monitor out.  
NOTE:  
• INPUT SOURCE changes if the INPUT 1 button on the remote control is  
pressed.  
• HDCP (High-bandwidth Digital Content Protection) is a system for protecting  
digital entertainment content which is delivered by DVI (Digital Visual Interface)  
from being copied. The specification of HDCP is decided and controlled by  
Digital Content Protection, LLC. Should the specification be changed, this  
projector may not display the digital content protected by HDCP.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )  
When connecting a computer output [5 BNC Type (Green,  
Blue, Red, Horiz. Sync, and Vert. Sync.)] from a computer to  
G, B, R, H/HV, and V jacks:  
INPUT MENU  
INPUT Menu icon  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the INPUT Menu icon.  
1
Move the pointer (red arrow) to Input 2  
and press the SELECT button.  
Press the POINT UP/DOWN buttons to move the red arrow  
pointer to Input 2 and then press SELECT button. A Source  
Select Menu appears.  
2
Input 2  
Press the POINT UP/DOWN buttons and a red-arrow icon  
appears. Move the arrow to “RGB,” and then press the  
SELECT button.  
3
Source Select Menu  
Move the pointer (red arrow)  
to RGB and press the  
SELECT button.  
NOTE:  
• INPUT SOURCE changes if the INPUT 2 button on the remote control is  
pressed.  
SELECTING COMPUTER SYSTEM  
AUTOMATIC MULTI-SCAN SYSTEM  
This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+,  
WXGA, or UXGA (refer to “COMPATIBLE COMPUTER SPECIFICATIONS” on pages 54-55). When Computer  
is selected, this projector automatically detects the incoming signal and projects proper image without any  
additional setting. (Some computers need to be set manually.)  
The projector displays one of these: Auto, -----, Mode 1~10, or the system provided in the projector.  
When the projector cannot recognize a connected signal  
as PC system provided in this projector, the Auto PC  
Auto  
PC SYSTEM MENU  
Adjustment function operates to adjust the projector and  
“Auto” is displayed on the SYSTEM Menu icon.  
When the image is not provided properly, a manual  
adjustment is required. (See pages 27 and 28.)  
PC SYSTEM Menu icon  
Displays system being selected.  
There is no signal input from the computer. Make sure  
the connection of a computer and the projector is set  
correctly. (See “TROUBLESHOOTING” on page 50.)  
-----  
The User preset adjustment in MANUAL PC  
ADJUSTMENT. The Adjusted data can be stored in  
the Mode 1~10.  
Mode 1  
SVGA 1  
PC systems provided in this projector. The projector  
chooses proper system and displays it.  
Mode 1 and SVGA 1 are examples.  
PC SYSTEM MENU  
SELECTING COMPUTER SYSTEM MANUALLY  
This projector automatically selects PC system among those  
provided in this projector, however, PC system can be also  
selected manually.  
PC SYSTEM Menu icon  
Displays system being selected.  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the PC SYSTEM Menu icon.  
Systems in this dialog box can be  
selected.  
1
Custom Mode (1~10) set in PC  
ADJUST Menu. (p.27, 28)  
Press the POINT UP/DOWN buttons to move the red arrow  
pointer to the desired system, and then press SELECT button.  
2
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PC ADJUSTMENT  
AUTO PC ADJUSTMENT  
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical  
positions to conform to your computer. Auto PC Adjustment function can be operated as follows.  
Auto PC adj.  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the PC ADJUST Menu icon.  
1
PC ADJUST MENU  
Press the POINT UP/DOWN buttons to move the red frame  
pointer to the AUTO PC adj. icon and then press the SELECT  
button.  
PC ADJUST Menu icon  
2
This Auto PC Adjustment can be also executed by pressing  
the AUTO PC ADJ. button on the top control or on the remote  
control.  
Move the red frame pointer to the Auto PC  
adj. icon and press the SELECT button.  
To store the adjusted parameters.  
The system parameters from Auto PC Adjustment can be memorized in this  
projector. Once the parameters are stored, the setting can be done just by  
selecting Mode in PC SYSTEM Menu (p.25). See MANUAL PC  
ADJUSTMENT on pages 27-28.  
NOTE:  
• Fine sync, Total dots, and Picture Positions of some computers can not be fully  
adjusted with the Auto PC Adjustment function. When the image is not provided  
properly with this function, manual adjustments are required. (See pages 27 and  
28.)  
• Auto PC Adjustment function cannot be operated in Digital Signal Input on the  
DVI terminal and “480p,” “575p,” “480i,” “575i,” “720p (HDTV),” “1035i  
(HDTV),” or “1080i (HDTV)” is selected on the PC SYSTEM Menu.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
MANUAL PC ADJUSTMENT  
This projector can automatically tune to display signals from most personal computers currently distributed.  
However, some computers employ special signal formats which may not be tuned by the Multi-Scan system of  
this projector. If this happens, the projector cannot reproduce proper image and it may be recognized as a  
flickering; non-synchronized; non-centered; or skewed picture.  
Manual PC Adjustment of this projector enables you to precisely adjust several parameters to match with those  
special signal formats. This projector has 10 independent memory areas to store those parameters manually  
adjusted, which allows you to recall setting for a specific computer whenever you use it.  
Note: The PC ADJUST Menu cannot be operated when the digital signal input on the DVI terminal is selected  
on PC SYSTEM Menu. (p.25)  
PC ADJUST MENU  
Press the MENU button to display the On-Screen Menu.  
1
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the PC ADJUST Menu icon.  
PC ADJUST Menu icon  
Press the POINT UP/DOWN buttons to move the red frame  
2
pointer to the desired item, and then press the SELECT  
Move the red frame pointer to an item  
button. An Adjustment dialog box appears. Press the POINT  
and press the SELECT button.  
LEFT/RIGHT buttons to adjust the value.  
Fine sync  
Eliminate a flicker from the display. Press the POINT LEFT/RIGHT  
buttons to adjust the value. (From 0 to 31.)  
Shows status (Stored/Free)  
of the selected Mode.  
Total dots  
Adjust the number of total dots in one horizontal period. Press the  
POINT LEFT/RIGHT buttons to adjust the number to match your  
PC image.  
Selected Mode  
Position H  
Press the POINT LEFT/RIGHT  
Press the POINT LEFT/RIGHT buttons to adjust the horizontal  
buttons to adjust the value.  
picture position.  
Press the SELECT button at this icon  
to adjust “Clamp,” “Display area H,” or  
Position V  
“Display area V.”  
Press the POINT LEFT/RIGHT buttons to adjust the vertical picture  
position.  
Current mode  
Press the SELECT button to show H-sync freq. and V-sync freq. of  
the connected computer.  
Current mode  
Clamp  
Adjusts the clamp level. When the image has a dark bars, try this  
adjustment.  
Press the SELECT  
button at the Current  
mode icon to show  
information of the  
Display area H  
Adjust the horizontal area displayed by this projector. Press the  
POINT LEFT/RIGHT buttons to decrease/increase the value.  
computer connected.  
Press the SELECT button at this icon  
to display the previous items.  
Display area V  
Adjust the vertical area displayed by this projector. Press the  
POINT LEFT/RIGHT buttons to decrease/increase the value.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
Reset  
To store adjustment data.  
To reset the adjusted parameters, select Reset and press the  
SELECT button. A confirmation box appears. Select [Yes]. All  
the adjustments return to their previous figures.  
This Mode has parameters being stored.  
Mode free  
To clear adjusted parameters previously set, move the red frame  
pointer to the Mode free icon and then press the SELECT  
button. Move the red arrow pointer to a Mode that you want to  
clear and then press the SELECT button.  
Store  
To store the adjusted parameters, move the red frame pointer to  
the Store icon and then press the SELECT button. Move the red  
arrow pointer to any of the Mode 1 to 10 in which you want to  
store the parameters and then press the SELECT button.  
Close this dialog box.  
Vacant  
Shows the values of “Total  
dots,” “Position H,” “Position V,”  
“Display area H,” and “Display  
area V.”  
Quit  
Exit the PC ADJUST Menu.  
A confirmation box appears  
and then select [Yes].  
To clear adjustment data.  
Close this dialog box.  
A confirmation box appears  
and then select [Yes].  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE IMAGE SELECT  
IMAGE LEVEL SELECT  
DIRECT OPERATION  
IMAGE button  
Select an image level from among Standard, Real, and  
Image 1 to Image 10 by pressing the IMAGE button on the  
top control or on the remote control.  
Standard  
Real  
Standard  
Normal picture level preset on this projector.  
Image 1  
Real  
Picture level with improved halftone for graphics.  
Image 10  
IMAGE 1~10  
User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-  
37)  
MENU OPERATION  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
Press the POINT UP/DOWN buttons to move the red frame  
pointer to the desired level and then press the SELECT  
button.  
2
IMAGE SELECT Menu icon  
Standard  
Move the red frame pointer to a level and  
press the SELECT button.  
Normal picture level preset on this projector.  
Real  
Picture level with improved halftone for graphics.  
IMAGE 1~10  
User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-  
37)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE SCREEN ADJUSTMENT  
PICTURE SCREEN SELECT  
This projector has a picture screen resize function, which enables you to display the desirable image size.  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the SCREEN Menu icon.  
SCREEN MENU  
1
Press the POINT UP/DOWN buttons and move the red frame  
pointer to the desired function and then press the SELECT  
button.  
2
SCREEN Menu icon  
Move the red frame pointer to a function and  
press the SELECT button.  
Normal  
Provides the image to fit the screen size.  
True  
NOTE:  
• True, Full, and Digital zoom +/– cannot be operated when  
“480i,” “575i,” “480p,” “575p,” “720p,” “1035i (HDTV),”  
or “1080i (HDTV)” is selected on the PC SYSTEM Menu.  
(p.25)  
Provides image in its original size.  
Wide  
• The Screen Menu cannot be operated when “720p  
(HDTV),” “1035i (HDTV),” or “1080i (HDTV)” is selected  
on the PC SYSTEM Menu. (p.25)  
• This projector cannot display any resolution higher than  
1600 x 1200. If your computer’s screen resolution is  
higher than 1600 x 1200, lower the resolution before  
connecting the projector.  
Provides the image to fit the wide video aspect ratio (16:9) by  
expanding the image width uniformly. This function can be used to  
provide the squeezed video signal at 16:9.  
Full  
Provides the full screen image.  
• The image data other than XGA (1024 x 768) is modified to  
fit the screen size in initial mode.  
• The Panning function may not operate properly if the  
computer system prepared on the PC ADJUST Menu is  
used.  
Digital zoom +  
When the Digital zoom + is selected, the On-Screen Menu  
disappears and “D. Zoom +” appears. Press the SELECT button to  
expand the image size. Press the POINT UP/DOWN/LEFT/RIGHT  
buttons to pan the image. The Panning function can work only  
when the image is larger than the screen size.  
The projected image can be also expanded by pressing the  
D.ZOOM button on the remote control.  
Digital zoom –  
When the Digital zoom – is selected, the On-Screen Menu  
disappears and “D. Zoom –” appears. Press the SELECT button to  
compress the image size.  
The projected image can be also compressed by pressing the  
D.ZOOM button on the remote control.  
To cancel the Digital Zoom +/– mode, press any button except  
D.ZOOM /, SELECT, POINT, and LASER buttons.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING INPUT SOURCE  
DIRECT OPERATION  
INPUT button  
Select an INPUT source by pressing the INPUT button on  
the top control or the INPUT 1, INPUT 2, or INPUT 3 buttons  
on the remote control.  
If the projector cannot reproduce proper image, select a  
correct input source through MENU OPERATION (see  
below).  
Input 1  
Input 2  
Input 3  
Input 1 is not displayed when the Input 1 is used as  
Monitor out.  
MENU OPERATION  
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )  
When connecting to video equipment, select a type of Video  
source in the Source Select Menu.  
INPUT MENU  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the INPUT Menu icon.  
1
INPUT Menu icon  
Move the pointer (red arrow) to Input 2  
and press the SELECT button.  
Press the POINT UP/DOWN buttons to move the red arrow  
pointer to Input 2 and then press the SELECT button. A  
Source Select Menu appears.  
2
Input 2  
Move the pointer to a source that you want to select and then  
3
press the SELECT button.  
Source Select Menu  
When the video input signal is connected to the  
VIDEO jack, select Video.  
Video  
Move the pointer (red arrow)  
to Video or Y, Pb/Cb, Pr/Cr  
and press the SELECT  
button.  
When the video input signal is connected to the Y-  
Pb/Cb-Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.  
Y, Pb/Cb, Pr/Cr  
NOTE:  
• INPUT SOURCE changes if the INPUT 2 button on the remote control is  
pressed.  
WHEN SELECTING INPUT 3 (AV TERMINALS )  
When connecting to video equipment, select a type of Video  
source in the Source Select (Video) Menu.  
INPUT MENU  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the INPUT Menu icon.  
1
INPUT Menu icon  
Press the POINT UP/DOWN buttons to move the red arrow  
pointer to Input 3 and then press the SELECT button. A  
Source Select Menu appears.  
2
Move the pointer (red arrow) to Input 3  
and press the SELECT button.  
Input 3  
Move the pointer to a source that you want to select and then  
3
press the SELECT button.  
Source Select Menu  
Move the pointer (red arrow)  
to a source and press the  
SELECT button.  
When the video input signal is connected to the  
Video  
VIDEO jack, select Video.  
When the video input signal is connected to the Y-  
Pb/Cb-Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.  
Y, Pb/Cb, Pr/Cr  
When the video input signal is connected to the S-  
VIDEO jack, select S-Video.  
S-Video  
NOTE:  
• INPUT SOURCE changes if the INPUT 3 button on the remote control is  
pressed.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING VIDEO SYSTEM  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the AV SYSTEM Menu icon.  
1
2
Press the POINT UP/DOWN buttons to move the red arrow  
pointer to the desired system and then press the SELECT  
button.  
VIDEO JACK OR S-VIDEO JACK  
AV SYSTEM MENU (VIDEO OR S-VIDEO)  
Auto  
The projector automatically detects an incoming video system, and  
adjusts itself to optimize its performance.  
AV SYSTEM Menu icon  
This box indicates system being  
selected.  
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N  
If the projector cannot reproduce proper video image, select a  
specific broadcast signal format from among PAL, SECAM, NTSC,  
NTSC 4.43, PAL-M, and PAL-N.  
Move the pointer (red arrow) to  
system and press the SELECT button.  
Y, Pb/Cb, Pr/Cr JACKS  
AV SYSTEM MENU (COMPONENT VIDEO)  
Auto  
The projector automatically detects an incoming video signal, and  
adjusts itself to optimize its performance.  
When the Video System is 1035i or 1080i, select the system  
manually.  
AV SYSTEM Menu icon  
This box indicates system being  
selected.  
COMPONENT VIDEO SIGNAL FORMAT  
Move the pointer (red arrow) to  
system and press the SELECT button.  
If the projector cannot reproduce proper video image, select a  
specific component video signal format from among 480i, 575i,  
480p, 575p, 720p, 1035i, and 1080i.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
PICTURE IMAGE SELECT  
IMAGE LEVEL SELECT  
DIRECT OPERATION  
IMAGE button  
Standard  
Select an image level from among Standard, Cinema, Image  
1 to Image 10 by pressing the IMAGE button on the top  
control or on the remote control.  
Cinema  
Image 1  
Standard  
Normal picture level preset on this projector.  
Cinema  
Picture level adjusted for picture with fine tone.  
Image 10  
IMAGE 1~10  
User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-  
37)  
MENU OPERATION  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the IMAGE SELECT Menu icon.  
1
IMAGE SELECT MENU  
Press the POINT UP/DOWN buttons to move the red frame  
pointer to the desired level and then press the SELECT  
button.  
IMAGE SELECT Menu icon  
2
Move the red frame pointer to a level and  
press the SELECT button.  
Standard  
Normal picture level preset on this projector.  
Cinema  
Picture level adjusted for picture with fine tone.  
IMAGE 1~10  
User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-  
37)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
PICTURE SCREEN ADJUSTMENT  
PICTURE SCREEN SELECT  
This projector has a picture screen resize function, which enables you to customize the image size.  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the SCREEN Menu icon.  
1
SCREEN MENU  
Press the POINT DOWN button and move the red frame  
pointer to the desired function and then press the SELECT  
button.  
SCREEN Menu icon  
2
Move the red frame pointer to a function and  
press the SELECT button.  
Normal  
Provides image at the normal video aspect ratio of 4:3.  
NOTE:  
• SCREEN Menu can not be operated when “720p,”  
“1035i,” or “1080i” is selected on AV SYSTEM Menu  
(p.32).  
Wide  
Provides image at the wide screen ratio of 16:9.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE IMAGE  
PICTURE IMAGE ADJUSTMENTS  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the IMAGE ADJUST Menu icon.  
1
2
IMAGE ADJUST MENU  
Press the POINT UP/DOWN buttons to move the red frame  
pointer to the desired item and then press the SELECT  
button. The level of each item is displayed. Adjust each level  
by pressing POINT LEFT/RIGHT buttons.  
IMAGE ADJUST Menu icon  
Move the red frame pointer to item to be  
selected and then press SELECT button.  
Contrast  
Press the POINT LEFT button to decrease contrast; press the  
POINT RIGHT button to increase the contrast. (From 0 to 63.)  
Brightness  
Press the POINT LEFT button to decrease the brightness; press  
the POINT RIGHT button to increase the brightness. (From 0 to  
63.)  
Color  
Press the POINT LEFT button decrease the intensity of the color;  
press the POINT RIGHT button to increase the intensity of the  
color. (From 0 to 63.)  
Tint  
Press the POINT LEFT/RIGHT buttons to adjust the tint value to  
obtain proper color balance. (From 0 to 63.)  
Color Management  
Press the POINT LEFT/RIGHT buttons to  
adjust the value.  
The Color management function can be used to adjust the LEVEL,  
PHASE, and GAMMA of the selected display colors (except for  
black, white, and gray) on the screen and replace these colors with  
other colors if required.  
You can store up to eight (8) color management data.  
Press the POINT UP/DOWN buttons to move the red frame  
pointer to Color management, and then press the SELECT  
button. The image being projected freezes, and the COLOR  
MANAGEMENT POINTER appears.  
1
POINTER MODE  
Use the POINT UP/DOWN/LEFT/RIGHT buttons to move the  
pointer to a spot where you want to adjust the color and then  
press the SELECT button. The COLOR SELECTION window  
appears, and the color in the center of the pointer is selected  
and you can adjust the color.  
2
COLOR MANAGEMENT  
POINTER  
NOTE:  
Use the POINT UP/DOWN/LEFT/RIGHT buttons to adjust the  
Press the COLOR M. button on the remote control  
to display the COLOR MANAGEMENT POINTER.  
If you would like to check or readjust the color  
management setting that has already been made,  
press the COLOR M. button on the remote control  
once more to display the COLOR MANAGEMENT  
LIST.  
3
LEVEL and PHASE of the color, and then press the SELECT  
button to confirm the setting. Then use the POINT UP/DOWN  
buttons to adjust the GAMMA for the color and press the  
SELECT button to accept the setting. After adjusting, press  
the SELECT button to go to the COLOR MANAGEMENT  
LIST.  
COLOR SELECTION MODE  
LIST  
Go to the COLOR MANAGEMENT LIST.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE IMAGE  
COLOR SELECTION MODE (continued)  
COLOR SELECTION MODE  
COLOR M.  
Level and phase  
Gamma  
adjustment palette.  
adjustment palette.  
Return to the COLOR MANAGEMENT POINTER. (If you  
press the MENU button on the top control or the remote  
control, it returns to the COLOR MANAGEMENT POINTER  
and you will need to reselect and readjust the color.)  
MENU  
Return to the IMAGE ADJUST Menu. But any settings that  
have been changed will not be stored. To store the changed  
settings, be sure to select “LIST” and go to the COLOR  
MANAGEMENT LIST.  
In the COLOR MANAGEMENT LIST, the adjusted color data  
are check marked. You can decide whether or not to apply  
the adjusted color data in the list to the projected image (see  
below).  
4
LIST  
COLOR M.  
MENU  
LIST MODE  
LIST MODE  
Clear the check mark if you do not want to apply the adjusted  
color data; select the check mark and then press the SELECT  
button. The check make disappears.  
COLOR PALETTE  
DEL  
COLOR PALETTE  
Return to the COLOR SELECTION mode so that you can  
readjust the setting for the color in that line. (This option is not  
available if the check mark is cleared.)  
DEL  
Select the DEL box if you want to delete the adjusted data.  
Press the SELECT button and a confirmation box appears  
and then select [Yes]  
ALL DEL  
Delete all the data in the list. Press the SELECT button and a  
confirmation box appears and then select [Yes].  
MENU  
ALL DEL  
NOTE:  
MENU  
COLOR M.  
The same function as stated above.  
COLOR M.  
If you press the COLOR M. button on the remote  
control, the display returns to the normal projection  
screen, but any settings that have been changed  
will not be stored. To store the changed settings,  
be sure to select “MENU” to return to the IMAGE  
ADJUST Menu and store the settings.  
The same function as stated above.  
Auto picture control  
Press the POINT LEFT/RIGHT buttons to select the desired Auto  
picture control position (Off, L1 or L2).  
Off . . . . Auto picture control OFF position.  
L1 . . . . . Auto picture control LEVEL 1 position.  
L2 . . . . . Auto picture control LEVEL 2 position.  
Color temp.  
Press either the POINT LEFT/RIGHT buttons to select the desired  
Color temp. level (XLow, Low, Mid or High).  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PICTURE IMAGE  
White balance (Red)  
Press the POINT LEFT button to lighten red tone; press the POINT  
RIGHT button to deepen red tone. (From 0 to 63.)  
White balance (Green)  
Press the POINT LEFT button to lighten green tone; press the  
POINT RIGHT button to deepen green tone. (From 0 to 63.)  
White balance (Blue)  
Press the POINT LEFT button to lighten blue tone; press the  
POINT RIGHT button to deepen blue tone. (From 0 to 63.)  
Press the SELECT button at this icon to  
display other items.  
Sharpness  
Press the POINT LEFT button to decrease the sharpness of the  
image; press the POINT RIGHT button to increase the sharpness of  
the image. (From 0 to 31.)  
Press the SELECT button at this  
icon to display the previous items.  
Gamma  
Press the POINT LEFT/RIGHT buttons to adjust the gamma value  
to obtain better balance of contrast. (From 0 to 15.)  
Press the POINT LEFT/RIGHT  
buttons to adjust the value.  
Noise reduction  
Noise interference on the screen can be reduced. Press the POINT  
LEFT/RIGHT buttons to change the noise reduction mode.  
Off . . . . Noise reduction mode is “Off”  
L1 . . . . . For lower reduction  
L2 . . . . . For higher reduction  
Progressive  
An interlaced video signal can be displayed in progressive. Press  
the POINT LEFT/RIGHT buttons to change the progressive scan  
mode.  
Off . . . . Progressive scan mode is “Off.”  
On . . . . Progressive scan mode is “On.”  
Film . . . Select for watching a film. With this function, the  
projector reproduces pictures faithful to the original film  
quality.  
NOTE:  
• The Film mode in the Progressive function cannot be selected when the video  
signal format is 1080i or 1035i.  
Reset  
To reset the adjusted parameters, select Reset and press the  
SELECT button. A confirmation box appears. Select [Yes]. All the  
adjustments return to their previous figures.  
Image Level Menu  
Move the red frame pointer to any of  
Image 1 to 10 where you want to set  
and then press the SELECT button.  
Store  
To store the manually preset image, move the red frame pointer to  
the Store icon and press the SELECT button. The Image Level  
Menu appears. Move the red arrow pointer to any of the Mode 1 to  
10 in which you want to set and press the SELECT button.  
Store icon  
Press the SELECT button at this  
icon to store the adjustment.  
Quit  
Exit the IMAGE ADJUST Menu.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
SETTING MENU  
This projector has Setting menu that allows you to set up the other various functions described as follows:  
Press the MENU button to display the On-Screen Menu.  
Press the POINT LEFT/RIGHT buttons to move the red frame  
pointer to the Setting Menu icon.  
1
SETTING MENU (LANGUAGE)  
Press the POINT DOWN button to move the red frame pointer  
2
SETTING Menu icon  
to the desired item that and then press the  
SELECT button.  
The Setting dialog box appears.  
Set the red frame pointer  
to the item and press the  
SELECT button.  
Language  
The language used in the On-Screen Menu is available in English,  
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,  
Russian, Chinese, Korean, or Japanese.  
Keystone  
This function corrects distortion of a projected image. Select either  
Store or Reset with the POINT LEFT/RIGHT buttons, and then  
press the Select button. The Keystone dialog box appears. Correct  
keystone with the POINT UP/DOWN/LEFT/RIGHT buttons. (p.22)  
Store . . . stores the keystone correction even if the AC power  
cord is unplugged.  
When pressing the SELECT  
button at Language, the  
Language Menu appears.  
Reset . . resets the keystone correction when the AC power cord  
is unplugged.  
Background  
Three background settings are available in this projector. Select  
one of the following options when no input source is connected to  
the projector or no input signal is coming from the connected  
equipment.  
Blue . . . blue colored background  
User . . . the image you captured  
Black . . black colored background  
Display  
This function decides whether to display On-Screen Displays.  
On . . . . . . . . . . . . shows all the On-Screen Display.  
Count-down Off . . hide the Count-down Display.  
Off . . . . . . . . . . . . hide the On-Screen Display except:  
On-Screen Menu  
“Power off?”  
P-TIMER (p.23)  
”Please wait....”  
Color management operation screen (p.35-  
36)  
“No signal” for Power management (p.40)  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
Logo  
Logo  
This function allows you to customize the screen logo with Logo  
select, Capture, and Logo PIN code lock functions.  
Logo select  
This function decides the start-up display as follows:  
User . . . the image you captured  
Default . the factory-set logo  
Off . . . . count-down only  
Capture  
This function enables you to capture the image being projected  
and use it for a starting-up display.  
After capturing the projected image, go to the Logo select function  
and set it to “User.” Then the captured image will be displayed  
when turning on the projector the next time.  
Select [Yes] to  
capture the  
projected image.  
To capture the image, select [Yes]. To cancel the Capture  
function, select [No].  
NOTE:  
Select [Yes] to stop  
capturing.  
• Before capturing an image, select Standard in the IMAGE SELECT Menu to  
capture proper image. (See pages 29 and 33.)  
• A signal from a computer can be captured up to XGA (1024 X 768).  
• Certain signals may not be captured properly.  
• When capturing the image that has been adjusted by the Keystone function,  
the adjusted data is automatically reset and the projector captures an image  
without keystone correction.  
• When starting to capture a new image, the previously stored image is cleared  
even if you cancel the capturing.  
• Once you exit the Logo Menu after setting the Logo lock to "On," you are  
required to enter the PIN code every attempting to change the Logo setting.  
Logo PIN Code Lock Dialog Box  
Logo PIN code lock  
Pointer  
This function prevents an unauthorized person from changing the  
Logo setting.  
Off . . . . the Logo setting can be changed freely from the Logo  
function.  
Quit  
On . . . . the Logo setting cannot be changed without a Logo  
PIN code.  
After a correct Logo PIN code is entered, the following dialog box  
appears.  
If you want to change the Logo PIN code lock setting, enter a  
Logo PIN code by following the steps below. The initial Logo PIN  
code is set to “4321” at the factory.  
To Enter a Logo PIN code  
Select On/Off by pressing the POINT LEFT/RIGHT buttons or  
change the Logo PIN code.  
Select a number by pressing the POINT LEFT/RIGHT buttons and  
fix the number with the SELECT button. The number changes to  
.” If you fixed a wrong number, move the pointer to “Set” or  
“Clear” once by pressing the POINT DOWN button, then return to  
“Logo PIN code.” Enter the correct number.  
To Change the Logo PIN code  
Logo PIN code can be changed to your desired  
four-digit number. Select “Logo PIN code change”  
with the POINT DOWN button and press the  
SELECT button. Set a new Logo PIN code.  
Repeat this step to complete entering a four-digit number.  
When the four-digit number is fixed, the pointer automatically  
moves to “Set.” Press the SELECT button so that you can change  
the Logo PIN code lock setting.  
Be sure to write down the new Logo PIN code and  
keep it at hand. If you lost the number, you could  
no longer change the Logo PIN code setting. For  
details on the PIN code setting, refer to the  
relevant instructions of the PIN code lock function  
on page 43.  
If you entered a wrong Logo PIN code, “Logo PIN code” and the  
number (✳✳✳✳) turn red and disappear. Enter a Logo PIN code  
all over again.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
Ceiling  
Ceiling  
When this function is “On,” the picture is top/bottom and left/right  
reversed. This function is used to project the image from a ceiling-  
mounted projector.  
Rear  
Rear  
When this function is “On,” the picture is left/right reversed. This  
function is used to project the image to a rear projection screen.  
Anamorphic  
When this function is “On,” the screen image is forcibly changed to  
the 4:3 image, even if the input signal is HDTV.  
Simple menu  
When this function is “On,” the value adjustment bar in the picture  
IMAGE ADJUSTMENT Menu is displayed on the bottom left of the  
screen.  
Menu position  
This function is used to adjust the On-Screen Menu display  
position. When the SELECT button is pressed, the adjustment  
screen is displayed (arrows appear). Use the POINT UP/DOWN/  
LEFT/RIGHT buttons to adjust the position. After making the  
adjustment, press the SELECT button to return to the Menu screen.  
Power management  
Power management  
For reducing power consumption as well as maintaining the lamp  
life, the Power management function turns off the projection lamp  
when the projector is not used for a certain period.  
If the input signal is interrupted and no button is pressed for more  
than 30 seconds, the timer display with “No signal” appears on the  
screen to start the countdown. The countdown time can be set  
between 1 and 30 minutes.  
Time left until lamp off  
Select one of the following operations:  
Ready . . . . . When the lamp has been fully cooled down, the  
READY indicator starts blinking. In this condition,  
the projection lamp is turned on if the input signal is  
reconnected or any button on the top control or  
remote control is pressed.  
Shutdown . . When the lamp has been fully cooled down, the  
power is turned off.  
Off . . . . . . . The Power Management function is off.  
Press the SELECT button at Power  
management and this box appears.  
Choose one of three settings with  
the POINT LEFT/RIGHT buttons,  
and go to the timer with the POINT  
DOWN button and set time with the  
POINT LEFT/RIGHT buttons.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
On start  
When this function is “On,” the projector is automatically turned on  
just by connecting the AC power cord to an AC outlet.  
NOTE:  
• Be sure to turn the projector off properly (see “TURNING OFF THE PROJECTOR”  
on page 21). If the projector is turned off in the incorrect sequence, such as  
unplugging the AC power cord before completing the cool-down etc., the On  
start function does not operate properly.  
Lamp control  
This function allows you to change the brightness of the screen.  
. . . . brightness according to the input signal.  
. . . . normal brightness.  
. . . . lower brightness reduces the lamp power consumption  
and extends the lamp life.  
Remote control  
Remote control  
The eight different remote control codes (Code 1-8) are assigned to  
this projector: the factory-set, initial code (Code 1) and the other  
seven codes (Code 2 to Code 8). This switching function prevents  
interference from other remote controls when several projectors or  
video equipment next to each other are operated at the same time.  
For example, when operating the projector in “Code 7”, the code for  
both the projector and the remote control must be switched to  
“Code 7.”  
To change the code of the projector:  
Select from Code 1 to Code 8 in the SETTING Menu.  
To change the code of the remote control:  
Set the DIP switches 1-3 inside the battery compartment of the  
remote control. (See page 15.)  
When pressing the SELECT button at  
Remote control, the Remote Control  
Code Menu appears.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
USB  
This Projector has a USB port for interactive operation between the  
projector and computers. Set the mode by following the steps  
below.  
Wireless Mouse mode  
Select “  
” when controlling a computer with the remote control of  
this projector.  
Projector mode:  
” Not used.  
Security  
Security  
Key lock  
This function locks operation of the top control and remote  
control. It helps to prevent operation by an unauthorized  
person.  
. . . . unlocked.  
. . . . locks operation of the top control.  
To unlock, use the remote control.  
. . . . locks operation of the remote control.  
To unlock, use the top control.  
Key lock  
If the top control accidentally becomes locked and you do not  
have the remote control nearby, unplug the AC power cord  
from the AC outlet, and then hold down the SELECT button  
and reinsert the AC power cord. This will cancel the top  
control lock.  
Select Key lock and  
this box appears.  
Choose one of the  
alternatives with the  
POINT UP/DOWN  
buttons and select  
[Yes] to activate it.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
PIN code lock  
PIN code lock  
This function prevents the projector from being operated by an  
unauthorized person and provides the following settings for  
security options.  
Off . . . . the projector is not locked with the PIN code.  
On1 . . . requires to enter the PIN code every time turning on  
the projector.  
On2 . . . requires to enter the PIN code to operate the projector  
once the power cord is disconnected; as long as the  
AC power cord is connected, the projector can be  
operated without a PIN code.  
When the projector is  
locked with the PIN  
code, the PIN code  
lock mark appears on  
the menu bar.  
Whenever you change the PIN Code Lock setting or the PIN code  
(the four-digit number), you are required to enter the PIN code.  
“1234” is set as the initial PIN code at the factory.  
To Enter a Logo PIN code  
Select a number by pressing the POINT LEFT/RIGHT buttons and  
fix the number with the SELECT button. The number changes to  
.” If you fixed a wrong number, move the pointer to “Set” or  
“Clear” once by pressing the POINT DOWN button, then return to  
“PIN code.” Enter the correct number.  
Entering a PIN code  
Pointer  
Quit  
Repeat this step to complete entering a four-digit number.  
When the four-digit number is fixed, the pointer automatically  
moves to “Set.” Press the SELECT button so that you can change  
the PIN code lock settings.  
The input numbers  
change to “” for security.  
If you entered a wrong PIN code, “PIN code” and the number  
(✳✳✳✳) turn red and disappear. Enter a Logo PIN code all over  
again.  
When the pointer  
automatically moves to  
“Set,” press the SELECT  
button.  
To Change the PIN Code Lock setting  
Select “Off,” “On1,” or “On2” with the POINT LEFT/RIGHT buttons  
and then go to “Quit” with the POINT DOWN button. Press the  
SELECT button to close the dialog box.  
To Change the PIN Code  
Changing the PIN code lock setting  
The PIN code can be changed to your desired four-digit number.  
Select “PIN code change” with the POINT DOWN button, and  
press the SELECT button. A New PIN code input dialog box  
appears.  
Select a desired setting  
with the POINT  
LEFT/RIGHT buttons.  
Select a number with the POINT LEFT/RIGHT buttons and fix the  
number with the SELECT button. Repeat it to complete entering a  
four-digit number. When the four-digit number is fixed, the pointer  
automatically moves to “Set.” Then press the SELECT button.  
Change the PIN code  
Select PIN code  
change and press the  
SELECT button. The  
New PIN code input  
dialog box appears.  
CAUTION:  
WHEN YOU HAVE CHANGED THE PIN CODE, WRITE DOWN  
A NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO  
ON PAGE 60, AND KEEP IT SECURELY. SHOULD THE PIN  
CODE BE LOST OR FORGOTTEN, THE PROJECTOR CAN NO  
LONGER BE OPERATED.  
The input numbers  
are being displayed  
for confirmation.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
Factory default  
Lamp counter  
This function is used to reset the Lamp replacement counter. When  
replacing the projection lamp, reset the Lamp replacement counter  
with this function. See page 49 for operation.  
Select Factory default and this box  
appears. Select [Yes], and the next  
box appears.  
Factory default  
This function returns all setting values except for the User logo,  
Key lock, PIN code lock, Logo PIN code lock, and the Lamp counter  
to the factory default settings.  
Quit  
Exit the SETTING Menu.  
Select [Yes] to  
activate it.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
WIRELESS MOUSE  
Remote control is not only able to operate this projector but also functions as a wireless mouse for most  
personal computers. The MOUSE POINTER, DRAG ON/OFF button, and two CLICK buttons are used for  
wireless mouse operation.  
The Wireless mouse function is available only when the PC mouse pointer is displayed on the screen.  
INSTALLATION  
To use the remote control as a wireless mouse for a computer, installation of a mouse driver (not supplied) is  
required. Make sure that the mouse driver is properly installed on your computer and that the mouse port (or  
USB port) of the computer is activated.  
Connect the mouse port (or USB port) of your computer to the  
CONTROL PORT (or USB connector) of this projector with  
Note:When your computer has no mouse port,  
1
connect the Serial port of your computer to  
the Control cable (or USB cable). (See pages 12 and 13 for  
the Control port of the projector with the  
connection.)  
Control cable for Serial port (supplied).  
Turn on the projector first, and then turn your computer on. If  
the computer is switched on first, the Wireless mouse function  
may not work properly.  
2
OPERATING WIRELESS MOUSE  
When controlling the PC mouse pointer, use the MOUSE POINTER, DRAG ON/OFF button, LEFT CLICK  
button, and RIGHT CLICK button on the remote control.  
MOUSE POINTER  
Used to move the PC mouse pointer. The pointer moves to the  
direction you are pressing.  
DRAG ON  
INDICATOR  
LEFT CLICK button  
This button has the same function as the left button in a PC mouse.  
To drag a selected screen object, hold down this button and press  
the MOUSE POINTER.  
RIGHT CLICK button  
This button has the same function as the right button in a PC  
mouse.  
DRAG ON/OFF  
button  
DRAG ON/OFF button  
MOUSE POINTER  
(Moves the pointer)  
Use this button and the MOUSE POINTER to drag a selected  
screen object. Press and release the DRAG ON/OFF button, then  
the DRAG ON INDICATOR lights green and the remote control is in  
Drag mode. Use the MOUSE POINTER to drag an screen object.  
Press and release the DRAG ON/OFF button again or press any  
other button to drop the object.  
LEFT CLICK button  
(left button of the mouse)  
RIGHT CLICK button  
(right button of the mouse)  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
MAINTENANCE  
WARNING TEMP. INDICATOR  
The Warning Temp. indicator blinks red to let you know the internal  
temperature of the projector exceeds a normal level. If the temperature  
goes up further, the projector will be turned off automatically and the  
Ready indicator goes out. (The Warning Temp. indicator continues  
blinking.) After the cooling-off period, the Ready indicator lights on again  
and the projector can be turned on by pressing the POWER ON/OFF  
button on the top control or the remote control. When you turn on the  
projector, the Warning Temp. indicator goes out.  
TOP CONTROL  
If the Warning Temp. indicator is still blinking, check the following matters:  
- The ventilation slots of the projector may be blocked. In such a case,  
reposition the projector so that the ventilation slots are not obstructed.  
- The air filters may be clogged with dust particles. Clean them by  
following the section “AIR FILTER CARE AND CLEANING” on the next  
page.  
Warning Temp.  
Indicator  
Ready  
Indicator  
- If the WARNING TEMP. indicator remains on after performing above  
checks, the cooling fans or internal circuits may be malfunctioning.  
Contact the service station.  
When both of the Warning Temp. and Ready indicators are blinking:  
When the projector detects an internal problem, it shuts down automatically and both the Warning Temp. and  
Ready indicators start blinking. In this condition, the projector cannot be turned on even if you press the POWER  
ON-OFF button on the top control or remote control. If this happens, unplug and reconnect the AC power cord,  
and then turn on the projector again to check the operation. If the projector shuts down again or cannot to be  
turned on, internal checking and repair is required. Unplug the AC power cord and contact the service station.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
AIR FILTERS CARE AND CLEANING  
Air filters help prevent dust from accumulating on the optical elements inside the projector. To whatever extent  
the air filters become clogged with dust particles, the cooling fans’ effectiveness is reduced, which may result in  
an internal heat build-up and adversely affect the life of the projector. Therefore, for appropriate care and use of  
the projector, regular cleaning of the air filters is necessary.  
How often the air filters should be cleaned really depends upon the environment in which the projector is being  
operated. As a rough guide, under a normally clean operating environment, the air filters should be cleaned  
approximately every 200 hours of use. However, if the projector is being operated in a somewhat dusty or  
smoky environment, the air filters should be cleaned more often; for consistently good projector operation and  
performance, timely cleaning of the air filters is a very important factor. When appropriate, clean the air filters  
following the steps below.  
Turn off the projector and unplug the AC power cord from an  
AC outlet.  
1
A
B
Turn over projector and remove the air filters by pulling the  
latches upward.  
2
Clean the air filters with a brush or rinse them softly. When  
rinsing the air filters, dry them well.  
3
Replace the air filters properly. Make sure that the air filters  
are fully inserted to the projector.  
4
CAUTION  
AIR FILTERS  
Do not operate the projector with the air filters  
Pull up and remove.  
removed. Dust may accumulate on the LCD Panel and  
projection mirror degrading the picture quality. Do not  
put anything into the air intake vents. It may result in  
malfunction of the projector.  
NOTE: If the dust cannot be removed by  
cleaning, it is probably time to replace  
the air filters with new ones. Please  
consult your dealer.  
Air Filter (A) Parts No. 610 303 8773  
Air Filter (B) Parts No. 610 303 8780  
RECOMMENDATION  
We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments  
may cause a poor image quality.  
When using the projector under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical  
elements inside the projector. Such condition may degrade the quality of the projected image.  
When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning.  
CLEANING PROJECTION LENS  
Follow these steps to clean the projection lens:  
Turn off the projector and unplug the AC power cord from an AC outlet.  
1
Apply a non-abrasive camera lens cleaner to a dry soft cleaning cloth. Avoid using an excessive amount of cleaner.  
Abrasive cleaners, solvents ,or other harsh chemicals might scratch the surface of the lens.  
2
Gently wipe with the cleaning cloth over the projection lens.  
3
When the projector is not in use, put the lens cap.  
4
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
LAMP REPLACEMENT  
When the projection lamp of this projector reaches its  
end of life, the LAMP REPLACE indicator lights yellow. If  
this indicator lights yellow, replace the projection lamp  
with a new one promptly.  
TOP CONTROL  
This indicator lights yellow  
when the projection lamp  
reaches its end of life.  
Replace the projection lamp  
with a new one promptly.  
CAUTION  
Allow the projector to cool for at least 45 minutes  
before you open the lamp cover. The inside of the  
projector can become very hot.  
CAUTION  
For continued safety, replace with a lamp  
assembly of the same type.  
Do not drop the lamp assembly or touch a glass  
bulb! The glass can shatter and may cause injury.  
Follow these steps to replace lamp assembly.  
Turn off the projector and unplug the AC power cord.  
Allow the projector to cool for at least 45 minutes.  
1
Loosen the two (2) screws with a screwdriver and open  
the lamp cover.  
2
Loosen the two (2) screws with a screwdriver and pull out  
the lamp assembly by using the built in handle.  
3
LAMP COVER  
Replace the lamp assembly with a new one and tighten  
the two (2) screws. Make sure that the lamp assembly is  
set properly. Put back the lamp cover and tighten the two  
(2) screws.  
LAMP  
ASSEMBLY  
HANDLE  
4
Connect the AC power cord to the projector and turn on  
the projector.  
5
Reset the Lamp replacement counter (refer to”LAMP  
REPLACE COUNTER” on the next page).  
6
NOTE:  
• Do not reset the Lamp replacement counter when the projection lamp is  
not replaced.  
ORDER REPLACEMENT LAMP  
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following  
information to the dealer.  
Model No. of your projector  
Replacement Lamp Type No.  
:
:
LC-X71/LC-X71L  
POA-LMP101  
(Service Parts No. 610 328 7362)  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
LAMP REPLACE COUNTER  
Be sure to reset the Lamp replacement counter after the lamp assembly is replaced. When the Lamp  
replacement counter is reset, the LAMP REPLACE indicator stops lighting.  
Lamp counter  
Turn the projector on and press the MENU button to display  
the On-Screen Menu. Press the POINT LEFT/RIGHT buttons  
to move the red frame pointer to the SETTING Menu icon.  
1
2
3
Press the POINT UP/DOWN buttons to move the red frame  
pointer to Lamp counter and then press the SELECT button.  
The next box appears.  
Press the POINT UP/DOWN buttons to select Reset and then  
press the SELECT button. The “Lamp replacement counter  
reset?” appears. Move the pointer to [Yes] and then press the  
SELECT button.  
Select Lamp counter and this box  
appears. Select [Reset], and the  
next box appears.  
Another confirmation dialog box appears and select [Yes] to  
reset the Lamp replacement counter.  
4
Select [Yes], and then another  
confirmation box appears.  
NOTE:  
• Do not reset the Lamp replacement counter until after the projection lamp is  
replaced.  
Select [Yes] again  
to reset the lamp  
counter.  
LAMP HANDLING PRECAUTIONS  
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper  
handling may result in accidents, injury, or create a fire hazard.  
Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no  
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a  
shorter period of time than other similar lamps.  
If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights  
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow  
carefully the instructions in the LAMP REPLACEMENT section of this manual.) Continuous use of the  
lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.  
Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its  
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in  
which the projector and lamp are being used.  
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.  
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an  
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check  
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out  
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one  
should check the inside of the projector except those who are authorized trained technicians and who are  
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who  
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken  
glass.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TROUBLESHOOTING  
Before calling your dealer or service center for assistance, check the items below once again.  
1. Make sure you have connected the projector to your computer or video equipment as described in  
“CONNECTING PROJECTOR” on pages 12-14.  
2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly  
connected.  
3. Make sure that all power is switched on.  
4. If the projector still does not produce an image, restart your computer.  
5. If an image still does not appear, disconnect the projector from your computer and check your computer  
monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.  
(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the  
projector. Turn on equipment in the order of the projector and computer.)  
6. If a problem still persists, check the following solutions.  
Problem:  
No power.  
Try these Solutions  
Plug the power cord of the projector into an AC outlet.  
Make sure the READY indicator lights.  
Wait 90 seconds after the projector is turned off to restart the projector.  
NOTE: After pressing the POWER ON-OFF button to “OFF”, make sure the projector works  
as follows:  
1. LAMP indicator lights bright and the READY indicator turns off.  
2. After 90 seconds, the READY indicator lights green again and the projector may  
be turned on by pressing the POWER ON-OFF button.  
Check the WARNING TEMP. and READY indicators. If both indicators blink, the projector  
cannot be turned on.  
(See “TURNING ON/OFF PROJECTOR” on pages 20-21.)  
Check the projection lamp. (See page 48.)  
Adjust the focus of the projector.  
Make sure the projection screen is at least 4.6’ (1.4 m) away from the projector.  
Check the projection lens to see if it needs cleaning.  
Image is out of  
focus.  
NOTE: Moving the projector from a cool to a warm place may result in moisture  
condensation on the projection lens. If this happens, leave the projector off and wait  
until condensation evaporates.  
Check the Ceiling/Rear function. (See “SETTING” on page 40.)  
Picture is left/right  
reversed.  
Check the Ceiling function. (See “SETTING” on page 40.)  
Picture is top/bottom  
reversed.  
Check the Display function.(See “SETTING” section on page 38.)  
Some displays are  
not seen during  
operations.  
Check the connection between your computer or video equipment and the projector.  
When turning the projector on, it takes about 30 seconds to display the image.  
Check the system you selected is corresponding to your computer or video equipment.  
Make sure the temperature is not out of specified operating temperature (41 ˚F ~ 95 ˚F  
(5 ˚C ~ 35 ˚C)).  
No image.  
Check the audio cable connection from an audio input source.  
Adjust the audio source.  
No sound.  
Press the VOLUME (+) button.  
Press the MUTE button.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
Problem:  
Remote control does  
not work.  
Try these Solutions  
Check the batteries.  
Check if the ALL-OFF switch on the remote control is set to “ON.”  
Make sure there is no obstruction in between the Infrared remote receiver of the projector  
and the remote control.  
Make sure you are not too far from the projector when using the remote control.  
Maximum operating range is 16.4’ (5 m).  
Check the remote control code in the remote control.  
(See“SETTING” on page 41.)  
Check the cable connection between the projector and your computer.  
Check the mouse setting on your computer.  
Turn the projector on before turning on a computer.  
Wireless mouse  
function does not  
work.  
WARNING:  
High voltages are used to operate this projector. Do not attempt to open the cabinet.  
after following all operating instructions,  
If the problem still persists  
projector or the service center.  
contact the sales dealer where you purchased the  
Specify the model number and explain the difficulty. We will advise you how to obtain service.  
This symbol on the nameplate means the product is Listed by Underwriters  
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety  
standards against risk of fire, casualty, and electrical hazards.  
The CE Mark is a Directive conformity mark of the European Community (EC).  
Pixelworks ICs used.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
MENU TREE  
Computer Input/Video Input  
(1)  
Input 1  
RGB (PC analog)  
RGB (Scart)  
RGB (PC digital)  
RGB (AV HDCP)  
Monitor out  
Video  
Go to System  
Input  
(2)  
(3)  
(1)  
(2)  
(3)  
(2)  
Input 2  
Input 3  
Go to System  
Go to System  
Go to System  
Go to System  
Go to System  
Go to System  
Y, Pb/Cb, Pr/Cr  
RGB  
Video  
Y, Pb/Cb, Pr/Cr  
S-Video  
Computer Input  
(1)  
Mode 1  
Mode 2  
SVGA 1  
SVGA 2  
SVGA 3  
Standard  
Real  
System  
Image Select  
Image 1  
Image 10  
System displayed in the System Menu varies depending on the input signal.  
Auto PC adj.  
Normal  
True  
PC Adjust  
Screen  
Fine sync.  
Total dots  
Position H  
Position V  
Current mode  
Clamp  
0 - 31  
Wide  
Full  
D.zoom +  
D.zoom -  
Display area - H  
Display area - V  
Reset  
Yes/No  
Mode free  
Store  
Mode 1  
Mode 2  
Mode 3  
Mode 4  
Mode 5  
Mode 6  
Mode 7  
Mode 8  
Mode 9  
Mode 10  
Quit  
Quit  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
Video Input  
Computer Input/Vide Input  
(2)  
Auto  
Language  
English  
German  
French  
Italian  
System  
System  
Setting  
PAL  
SECAM  
NTSC  
NTSC 4.43  
PAL-M  
PAL-N  
Spanish  
Portuguese  
Dutch  
Swedish  
(3)  
Auto  
1080i  
1035i  
720p  
575p  
480p  
575i  
Russian  
Chinese  
Korean  
Japanese  
Quit  
Keystone  
Background  
Display  
Store/Reset  
Blue/User/Black  
Off/Countdown Off/On  
480i  
Logo  
Logo select  
Standard  
Cinema  
Image 1  
Capture  
Image Select  
Logo PIN code lock  
On/Off  
Logo PIN code change  
Quit  
Image 10  
Quit  
Ceiling  
On/Off  
On/Off  
On/Off  
On/Off  
Normal  
Wide  
Rear  
Screen  
Anamorphic  
Simple menu  
Menu position  
Power management  
Off  
Computer Input/Vide Input  
Ready  
Shut down  
1-30 Min.  
Quit  
Contrast  
0 - 63  
Image Adjust  
Brightness  
Color  
0 - 63  
0 - 63  
Tint  
0 - 63  
On-Start  
On/Off  
Color management  
Color  
Lamp control  
Auto/Normal/Eco  
Gamma  
List  
Remote Control  
All Del  
Code 1  
Color M.  
Menu  
Menu  
Color M.  
Code 8  
Quit  
Auto picture control  
Color temp.  
Off/L1/L2  
High  
USB  
Mouse  
Projector  
Mid  
Low  
Security  
Key lock  
Off  
XLow  
Projector  
Remote Control  
Quit  
Red  
0 - 63  
Green  
0 - 63  
Blue  
0 - 63  
Sharpness  
Gamma  
Noise reduction  
Progressive  
Reset  
0 - 31  
PIN code lock  
Off/On1/On2  
PIN code change  
Quit  
0 - 15  
Off/L1/L2  
Off/On/Film  
Yes/No  
Image 1  
Lamp counter  
Factory default  
Quit  
Yes/No  
Yes/No  
Store  
Image 10  
Quit  
Quit  
Volume  
Built-in SP  
Mute  
0 - 63  
Sound  
On/Off  
On/Off  
Quit  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
COMPATIBLE COMPUTER SPECIFICATIONS  
Basically this projector can accept a signal from all computers with V-, H-Frequency mentioned below, and less  
than 140 MHz of Dot Clock.  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
VGA 1  
VGA 2  
VGA 3  
VGA 4  
VGA 5  
VGA 6  
VGA 7  
MAC LC13  
MAC 13  
480i  
640 x 480  
720 x 400  
640 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
31.47  
31.47  
31.47  
37.86  
37.86  
37.50  
43.269  
34.97  
35.00  
15.734  
15.625  
31.47  
31.25  
35.156  
37.88  
46.875  
53.674  
48.08  
37.90  
34.50  
38.00  
38.60  
32.70  
38.00  
49.72  
48.36  
68.677  
60.023  
56.476  
60.31  
48.50  
44.00  
63.48  
36.00  
62.04  
61.00  
35.522  
46.90  
47.00  
58.03  
60.24  
59.88  
70.09  
70.09  
74.38  
72.81  
75.00  
85.00  
66.60  
66.67  
60.00  
50.00  
59.88  
50.00  
56.25  
60.32  
75.00  
85.06  
72.19  
61.03  
55.38  
60.51  
60.31  
51.09  
60.51  
74.55  
60.00  
84.997  
75.03  
70.07  
74.92  
60.02  
54.58  
79.35  
87.17  
77.07  
75.70  
86.96  
58.20  
58.30  
72.00  
75.08  
MAC 21  
SXGA 1  
SXGA 2  
SXGA 3  
SXGA 4  
SXGA 5  
SXGA 6  
SXGA 7  
SXGA 8  
SXGA 9  
SXGA 10  
SXGA 11  
SXGA 12  
SXGA 13  
SXGA 14  
SXGA 15 1280 x 1024  
SXGA 16 1280 x 1024  
SXGA 17  
SXGA 18  
SXGA 19 1280 x 1024  
SXGA 20 1280 x 1024  
SXGA 21 1400 x 1050  
SXGA+ 1 1400 x 1050  
SXGA+ 2 1400 x 1050  
SXGA+ 3 1400 x 1050  
1152 x 870  
1152 x 864  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 960  
1152 x 900  
1152 x 900  
68.68  
64.20  
62.50  
63.90  
63.34  
63.74  
71.69  
81.13  
63.98  
79.976  
60.00  
61.20  
71.40  
50.00  
50.00  
63.37  
76.97  
61.85  
46.43  
63.79  
91.146  
63.90  
63.97  
65.35  
65.12  
75.00  
80.00  
48.36  
47.70  
48.36  
56.16  
75.00  
81.25  
87.50  
93.75  
45.00  
37.50  
33.75  
33.75  
28.125  
75.06  
70.40  
58.60  
60.00  
59.98  
60.01  
67.19  
76.107  
60.02  
75.025  
60.00  
65.20  
75.60  
86.00  
94.00  
60.01  
72.00  
66.00  
86.70  
60.18  
85.024  
60.00  
60.19  
60.12  
59.90  
75.08  
75.08  
60.00  
60.00  
60.00  
72.00  
60.00  
65.00  
70.00  
75.00  
60.00  
50.00  
60.00  
60.00  
50.00  
––––––––  
(Interlace)  
––––––––  
(Interlace)  
––––––––  
(Progressive)  
––––––––  
(Progressive)  
575i  
480p  
575p  
1280 x 1024  
(Interlace)  
SVGA 1  
SVGA 2  
SVGA 3  
SVGA 4  
SVGA 5  
SVGA 6  
SVGA 7  
SVGA 8  
SVGA 9  
SVGA 10  
SVGA 11  
MAC 16  
XGA 1  
XGA 2  
XGA 3  
XGA 4  
XGA 5  
XGA 6  
XGA 7  
XGA 8  
XGA 9  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1280 x 1024  
(Interlace)  
1152 x 900  
1280 x 1024  
(Interlace)  
MAC  
MAC  
1280 x 960  
1280 x 1024  
1366 x 768  
1360 x 768  
1376 x 768  
1360 x 768  
1600 x 1200  
1600 x 1200  
1600 x 1200  
1600 x 1200  
WXGA 1  
WXGA 2  
WXGA 3  
WXGA 4  
UXGA1  
UXGA2  
UXGA3  
UXGA4  
720p  
720p  
1035i  
1080i  
1080i  
1024 x 768  
(Interlace)  
XGA 10  
XGA 11  
XGA 12  
XGA 13  
XGA 14  
XGA15  
MAC 19  
1024 x 768  
1024 x 768  
––––––––  
(Progressive)  
––––––––  
(Progressive)  
––––––––  
(Interlace)  
1024 x 768  
(Interlace)  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
––––––––  
(Interlace)  
––––––––  
(Interlace)  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
When a input signal is digital from DVI terminal, refer to the chart below.  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
D-VGA  
D-480p  
D-575p  
D-SVGA  
D-XGA  
640 x 480  
31.47  
31.47  
31.25  
37.879  
43.363  
48.36  
47.70  
48.36  
46.50  
63.98  
59.94  
59.88  
50.00  
60.32  
60.00  
60.00  
60.00  
60.00  
50.00  
60.02  
D-SXGA2  
D-SXGA+ 1  
D-720p  
1280 x 1024  
1400 x 1050  
60.276  
63.97  
45.00  
37.50  
33.75  
33.75  
28.125  
33.75  
28.125  
27.00  
58.069  
60.19  
60.00  
50.00  
60.00  
60.00  
50.00  
60.00  
50.00  
48.00  
720 x 480  
(Progressive)  
1280 x 720  
768 x 575  
(Progressive)  
(Progressive)  
1280 x 720  
(Progressive)  
D-720p  
800 x 600  
1920 x 1035  
(Interlace)  
D-1035i  
1024 x 768  
1920 x 1080  
(Interlace)  
D-1080i  
D-WXGA1 1366 x 768  
D-WXGA2 1360 x 768  
D-WXGA3 1376 x 768  
D-WXGA5 1368 x 768  
D-SXGA1 1280 x 1024  
1920 x 1080  
(Interlace)  
D-1080i  
D-1080psf/30  
D-1080psf/25  
D-1080psf/24  
1920 x 1080  
1920 x 1080  
1920 x 1080  
Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.  
NOTE: Specifications are subject to change without notice.  
INDICATORS AND PROJECTOR CONDITION  
Check the indicators for projector condition.  
Indicators  
WARNING  
TEMP.  
red  
LAMP  
REPLACE  
yellow  
Projector Condition  
READY  
green  
LAMP  
red  
The projector is OFF. (The AC power cord is unplugged.)  
The projector is ready to be turned on with the POWER ON-  
OFF button.  
The projector is operating normally.  
The Warning Temp. indicator blinks red to let you know the  
internal temperature of the projector exceeds a normal level. If  
the temperature goes up further, the projector will be turned  
off automatically and the Ready indicator goes out. When the  
projector is cooled down enough and the temperature returns  
to normal, the READY indicator lights green and the projector  
can be turned on again. (The WARNING TEMP. indicator  
keeps blinking.) Check and clean the air filters.  
The projector is cooled down enough and the temperature  
returns to normal. When turning on the projector, the  
WARNING TEMP. indicator stops blinking. Check and clean  
the air filters.  
• • • on  
• • • blinking  
• • • dim  
• • • off  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
Indicators  
WARNING  
READY  
TEMP.  
green  
LAMP  
REPLACE  
yellow  
Projector Condition  
LAMP  
red  
red  
The projector is in cooling mode. It cannot be turned on until  
the READY indicator lights green.  
The projector detects an abnormal condition and cannot be  
turned on. Unplug the AC power cord and plug it again to turn  
on the projector. If the projector is turned off again, disconnect  
the AC power cord and contact the dealer or the service  
center for service and checkup. Do not leave the projector on.  
It may cause electric shock or a fire hazard.  
The projector is in the Power management mode.  
The temperature inside the projector is abnormally high.  
The lamp cannot light up. (The projector is preparing for  
stand-by or the projection lamp is in cooling mode. The  
projector cannot be turned on until the cooling process is  
completed.)  
The lamp cannot light up. (The lamp has been cooled down  
enough and the projector is in stand-by mode and ready to be  
turned on with the POWER ON-OFF button.)  
The projection lamp reaches its end of life.  
Replace the lamp and then reset the Lamp replacement  
counter. The indicator is turned off.  
• • • on  
• • • flashing  
• • • dim  
• • • off  
*When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator  
lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp replacement counter after  
replacing the lamp.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TECHNICAL SPECIFICATIONS  
Multi-media Projector  
Projector Type  
12.6” x 6.6” x 16.8” (319 mm x 170.8 mm x 435.5 mm)  
19.8 lbs (9.0 kg) LC-X71, 18.0 lbs (8.2 kg) LC-X71L  
1.3” TFT Active Matrix type, 3 panels  
1024 x 768 dots  
(W x H x D)  
Dimensions  
Net Weight  
LCD Panel System  
Panel Resolution  
Number of Pixels  
Color System  
2,359,296 (1024 x 768 x 3 panels)  
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N  
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i  
H-sync. 15 k ~ 100 kHz, V-sync. 48 ~ 100 Hz  
High Definition TV Signal  
Scanning Frequency  
Projection Lens  
F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focus (LC-X71)  
4.6’ (1.4 m) ~ 48.3’ (14.7 m)  
Up and Down  
Throw distance  
Motorized Lens Shift  
Projection Image Size (Diagonal)  
Horizontal Resolution  
Projection Lamp  
Input 1 Jacks  
Adjustable from 31” to 400”  
800 TV lines (HDTV)  
300 watt type  
DVI Terminal (Digital) HDCP Compatible, HDB 15-pin Terminal (Analog)  
and Stereo Mini Type Jack (Audio)  
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H/V, and V),  
Stereo Mini Type Jack (Audio)  
Input 2 Jacks  
Input 3 Jacks  
Other Jacks  
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)  
and DIN 4-pin (S-Video)  
DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack  
and Pj-to NetDirector Connector  
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)  
0˚ to 10.5˚  
Built-in Speakers  
Feet Adjustment  
Voltage and Power  
Consumption  
AC 100 ~ 120 V (5.7 A Max. Ampere), 50/60 Hz (The U.S.A and Canada)  
AC 200 ~ 240 V (2.7 A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)  
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)  
Operating Temperature  
Storage Temperature  
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)  
Power Source  
Operating Range  
Dimensions  
Net Weight  
Laser Pointer  
:
:
:
:
:
AA or LR6 ALKALINE Type x 2  
16.4’ (5 m)/ 30˚  
2.0” x 1.4” x 7.6” (50 mm x 36 mm x 193 mm)  
0.35 lbs (160 g) (including batteries)  
Remote Control Transmitter  
(Max. Output: 1mW/Wave length: 650 20nm)  
Class II Laser  
Owner’s Manual (CD-ROM)  
Quick Reference Guide  
AC Power Cord  
Accessories  
Wireless/Wired Remote Control Transmitter and Batteries  
VGA Cable  
USB Cable  
Control Cable for Serial Port  
Lens Cap (LC-X71)  
Lens Attachment  
Lens Replacement And Installation Manual  
PIN Code Label  
Specifications are subject to change without notice.  
LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or  
less) may be ineffective by the characteristics of the LCD panels.  
Each projector has its own characteristics.  
When projecting with several projectors on the same screen or side by side, you may recognize different white balance and color uniformity on each  
projector.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
CONFIGURATIONS OF TERMINALS  
COMPUTER INPUT-1 TERMINALS (ANALOG)  
Terminal: HDB15-PIN  
1
2
3
4
5
6
7
8
Red Input  
Green Input  
Blue Input  
Sense 2  
9
+5V Power  
Pin Configuration  
10 Ground (Vert. sync.)  
11 Sense 0  
12 DDC Data  
2
1
5
4
3
10  
9
8
7
6
15  
Ground (Horiz.sync.) 13 Horiz. sync.  
14  
13  
12  
11  
Ground (Red)  
Ground (Green)  
Ground (Blue)  
14 Vert. sync.  
15 DDC Clock  
COMPUTER INPUT-1 TERMINAL (DIGITAL)  
Terminal: DVI 24-pin  
1
2
3
4
5
6
7
8
T.M.D.S. Data2–  
T.M.D.S. Data2+  
9
T.M.D.S. Data1–  
17 T.M.D.S. Data0–  
18 T.M.D.S. Data0+  
Pin Configuration  
10 T.M.D.S. Data1+  
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield  
1
9
2
3
4
5
6
7
8
No Connect  
No Connect  
DDC Clock  
DDC Data  
12 No Connect  
13 No Connect  
14 +5V Power  
15 Ground (for +5V)  
16 Hot Plug Detect  
20 No Connect  
21 No Connect  
22 T.M.D.S. Clock Shield  
23 T.M.D.S. Clock+  
24 T.M.D.S. Clock–  
10 11 12 13 14 15 16  
17 18 19 20 21 22 23 24  
No Connect  
CONTROL PORT CONNECTOR  
Terminal: Mini DIN 8-PIN  
PS/2  
-----  
Serial  
R X D  
-----  
ADB  
-----  
Pin Configuration  
1
2
3
4
5
6
7
8
CLK  
DATA  
GND  
-----  
ADB  
-----  
-----  
8
7
6
GND  
GND  
-----  
5
4
3
RTS/CTS  
T X D  
GND  
2
1
-----  
-----  
GND  
-----  
-----  
GND  
GND  
USB CONNECTOR (Series B)  
Pin Configuration  
1
2
3
4
Vcc  
- Data  
+ Data  
Ground  
2
3
1
4
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
OPTIONAL PARTS  
The parts listed below are optionally supplied. When ordering those parts, specify the item name and its Type  
No. to the sales dealer.  
DVI Cable  
Type No. : KA-DV20  
HDB 15 pin-SCART 21 pin Cable Type No. : AH-98881  
Long Zoom Lens  
Ultra Long Zoom Lens  
Short Zoom Lens  
Short Fixed Lens  
Remote Control Cable  
Pj-to NetDirector  
Type No. : AH-23132  
Type No. : AH-24241  
Type No. : AH-23122  
Type No. : AH-32011  
Type No. : POA-CA-RC30  
Type No. : PjNET-30  
LENS REPLACEMENT  
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector  
for wide variety of uses.  
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be  
installed or replaced by well-trained sales or service engineers. Do not attempt to install and replace the lens by  
yourself as it may cause injury.  
After installing the lens, attach the lens cap to the lens when setting up the projector.  
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector.  
To the sales and service engineer:  
Referring to the attached lens replacement and installation manual, replace or install the lens properly.  
PJ LINK NOTICE  
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information  
System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified  
conformance with PJLink Standard Class 1.  
EIKI Projector Input  
PJLink Input  
RGB 1  
Parameter  
Input1  
RGB (PC analog)  
RGB (Scart)  
RGB (PC digital)  
RGB (AV HDCP)  
Video  
11  
12  
31  
32  
21  
22  
13  
23  
24  
25  
RGB 2  
DIGITAL 1  
DIGITAL 2  
VIDEO 1  
VIDEO 2  
RGB 3  
Input2  
Input3  
Y, Pb/Cb, Pr/Cr  
RGB  
Video  
VIDEO 3  
VIDEO 4  
VIDEO 5  
Y, Pb/Cb, Pr/Cr  
S-video  
PJLink is a registered trademark of JBMIA.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
PIN CODE NUMBER MEMO  
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost  
the number and unable to use the projector, contact the service station.  
PIN Code Lock No.  
Factory default set No: 1 2 3 4*  
Logo PIN Code Lock No.  
Factory default set No: 4 3 2 1*  
* Should the four-digit number be  
changed, the factory set number will  
be invalid.  
While the projector is locked with the PIN code...  
Put on the label below (supplied) in a prominent place of the  
projector’s body while it is locked with a PIN code.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
DIMENSIONS  
12.6 (319.0)  
5.59 (142.0)  
Unit : inch (mm)  
2.39 (60.6)  
4.55 (115.5)  
4.61 (117.0)  
Screw Holes for Ceiling Mount  
Screw: M6  
Depth: 0.393 (10.0)  
3.74 (95.0)  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A-key to better communications  
Canada  
U.S.A.  
EIKI International, Inc.  
30251 Esperanza  
EIKI CANADA - Eiki International, Inc.  
P.O. Box 156, 310 First St. - Unit 2,  
Midland, ON, L4R 4K8, Canada  
Tel : 800-563-3454 (705)-527-4084  
Fax : 800-567-4069 (705)-527-4087  
E-Mail : [email protected]  
Rancho Santa Margarita  
CA 92688-2132  
U.S.A.  
Tel : 800-242-3454 (949)-457-0200  
Fax : 800-457-3454 (949)-457-7878  
E-Mail : [email protected]  
Eastern Europe  
EIKIˆ CZECH spol. s.r.o.  
Umelecká 15  
170 00 Praha 7  
Czech Republic  
Tel : +42 02 20570024  
+42 02 20571413  
Fax : +42 02 20571411  
E-Mail : [email protected]  
Deutschland & Österreich  
EIKI Deutschland GmbH  
Am Frauwald 12  
65510 Idstein  
Deutschland  
Tel : 06126-9371-0  
Fax : 06126-9371-14  
E-Mail : [email protected]  
Japan & Worldwide  
EIKI Industrial Company Limited.  
4-12 Banzai-Cho, Kita-Ku, Osaka,  
530-0028 Japan  
Tel : +81-6-6311-9479  
Fax : +81-6-6311-8486  
WorldWide Website http://www.eiki.com  
1AA6P1P5253-- KE6B  
© 2006 Eiki International, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Earthquake Sound Speaker 600WRMS User Manual
Eurotech Appliances Computer Accessories COM 1460 User Manual
FujiFilm Digital Camera 16315990 User Manual
Fusion Car Speaker CP AS1080 User Manual
Garmin Car Stereo System PAV80 User Manual
GE Cordless Telephone 00028056 User Manual
Geemarc Telephone TP38 User Manual
GE Food Warmer 169155 User Manual
Gigabyte Computer Hardware GA 945PLM DS2 User Manual
Gigabyte Network Card 6EA User Manual