CAUTION: This document provides instructions for
installing the DMV600BTEC in a “cold” (power off)
system, most of which also apply to live insertion or
hot swap systems. It is important to note that there
are additional, system-dependent considerations for
live insertion. See the Administration Guide for your
Dialogic® System Software release for detailed
information on live insertion.
Physical Description
Dialogic
DMV600BTEC
Media Board
Quick Install Card
12
7
6
5
4
8
1. Work at a static-safe area. Turn the power to the
chassis OFF if you do not have a live insertion
system. If you have live insertion capability, the
power to the chassis can remain ON.
E
T
E
T
11
10
H
E
R
N
E
T
H
E
R
N
E
T
Part Number 64-0079-02
Copyright © 2003-2007
Dialogic Corporation.
All Rights Reserved.
C
o
m
p
ac
tP
C
T1
R1
I
J1
J2
P
O
W
E
R
2. Remove the chassis cover plate or open the door
on both the front and back of the chassis.
9
3
T2
R2
1
3
Not
Used
A
L
A
R
M
S
2
4
3. Select an empty slot and remove the slot’s access
cover plates (if applicable).
R
E
D
L
Y
C
E
8
A
R
S
R
L
P
G
N
O
LO
/
2
B
A
S
T
A
T
U
S
C
K
Before You Begin
Protecting the Board from Damage
R
E
D
Y
C
E
L
R
A
S
R
Installing the Rear I/O Module
G
N
LO
L
O
B
P
A
C
K
Note: If you are installing hardware in a live insertion
system with the power on, you should install the rear
I/O module before the baseboard.
4. Install the I/O module in the rear of the selected
slot. Use the slot’s board guides as you insert the
board into the chassis slot. Make sure the tabs on
the board extractors engage the guide holes in the
chassis card cage, then lock down the board
extractors until the red locking tabs snap shut.
CAUTION: All computer boards are sensitive to
electrostatic discharge (“ESD”). Handle all static-
sensitive boards and components at a static-safe
work area, and observe anti-static precautions at all
times.
Not
Used
O
1
UT
O
F
SER
If you are not familiar with ESD safety precautions,
more.
VIC
E
4
CAUTION: CompactPCI backplane pins are easily
bent. Make sure that the board connectors are
mating properly with hand pressure before fully
seating the board. When using the board extractors
to seat the board, make sure to seat evenly.
Unpacking the Board
Unpack the Dialogic® DMV600BTEC Media Board
(“board”) according to the following steps:
1. Prepare a static-safeguarded work area.
2. Carefully remove the board from the shipping
carton and anti-static packaging. Handle the
board by the edges and avoid touching the
board’s components.
RJ48C
(T1 and 120-Ohm E1)
BNC
(75-Ohm E1)
CompactPCI Baseboard
Rear I/O Modules
1. Out of Service LED: Indicates board is out of service or
9. BNC Connectors (T1, R1, T2, R2,): Connectors to
external 75-Ohm E1 digital telephone network interfaces.
(Connectors T3, R3, T4, and R4 are not used in this
assembly.)
10. RJ48C Connectors (J1, J2): Connectors to external T1
or 120-Ohm E1 digital telephone network interfaces.
(Connectors J3 and J4 are not used in this assembly.)
in reset from host.
Installing Rear I/O Module
Unlocked
Position
2. Alarm/Status LEDs: During power-up, indicate Power
On Self Test (POST) status. During operation, the top
two sets of LEDs indicate status and alarms for the two
trunks (the bottom two sets of LEDs are unused):
Red–Indicates loss of clock on incoming line from
external network.
Bac
kplane
Rear I/O
Module
3. Lay the board on the static-dissipative work
surface.
Locked
Position
Note: Place boards in static-shielding bags when
carrying boards from station to station.
CAUTION: Do not remove the board from the anti-
static packaging until you are ready to install it.
Observe proper anti-static precautions at all times.
11. Ethernet Connector: The Ethernet connectors are not
functional on this assembly.
Yellow–Indicates loss of frame synchronization at far
end of external network.
Carrier Signal–Indicates board is powered up and
receiving signal from external T1 or E1 source.
Loopback–Indicates the T1 or E1 network is in loopback
CompactPCI
Chassis (Rear)
12. J5: Rear I/O module connector to CompactPCI
backplane.
The default configuration of the Rear I/O Modules provides
loopback connection (signals to the board are looped back to
the source) when the board is powered off and during board
initialization. To disable loopback mode on either trunk,
remove the shunts from the indicated jumper pins:
Installing the Baseboard
Note: If you are installing hardware in a live insertion
system with the power on, you should install the rear
I/O module before the baseboard.
5. Install the baseboard in the front of the selected
slot. Use the slot’s board guides as you insert the
board into the chassis slot. Make sure the tabs on
the board extractors engage the guide holes in the
chassis card cage, then lock down the board
extractors until the red locking tabs snap shut.
3. Power LED
4. Board Extractor (with red locking tab)
5. Global Memory Module
6. Signal Processor Daughterboard connector
7. Signal Processor Daughterboard
Installing the Hardware
Note: For a new installation, you should install the
hardware before installing the system software. If you
are adding boards to an existing system, there is no
need to uninstall or reinstall the software.
RJ48C I/O module
JP1 & JP2
BNC I/O module
JP100 & JP101
JP200 & JP201
Trunk 1
Trunk 2
JP3 & JP4
8. J1, J4, J5: Board connector to CompactPCI backplane.
J1 key conforms to PICMG universal hot swap.
Download from Www.Somanuals.com. All Manuals Search And Download.
|