Edelbrock Automobile Parts Small Block Chevrolet V8 User Manual

VICTOR GLIDDEN 18° CHEVY MANIFOLD  
For 4500 Series Carbs  
®
CATALOG #2859  
MODEL: Small Block Chevrolet V8  
PLEASE study these instructions, and the General Instructions, carefully before installing your new manifold. If you have any questions  
or problems, do not hesitate to contact our Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday through Friday,  
Pacific Standard Time or e-mail us at: [email protected].  
MANIFOLD: This manifold is designed for competition vehicles only! It is not intended to be used on the street as it does not have  
provisions for chokes, emission pieces, etc. The Victor 18° Chevy is designed for use with small block chevy aluminum raised port  
18° cylinder heads only; will not fit standard cast iron or 23° aluminum heads. This manifold fits cylinder blocks with a 9.000" deck  
height standard. Edelbrock recommends port matching and blending prior to use for optimum performance.  
ACCESSORIES & INSTALLATION ITEMS: Major recommendations are listed below. However, due to the variety of years, makes and  
models to be covered, please review each part listed in the Installation Items section of the Edelbrock catalog to decide whether more  
items are required for your specific vehicle than are mentioned in these instructions.  
CARBURETOR RECOMMENDATIONS: CAUTION - Use only carburetors recommended. If parts required for installation are  
unavailable locally, contact Edelbrock directly.  
Carburetor  
Holley 4500 Series  
Reference  
Parts Required for Installation  
If required #8016, #8101 and #641140  
None  
See Holley catalog for selection guidelines.  
#8101- Edelbrock Braided Steel dual feed fuel line kit.  
#641140 Russell -8 Braided Steel dual feed fuel line.  
#8016- Ball end stud.  
PORT MATCH: Each intake runner should be matched to the cylinder head port size on all four sides of runner exit. This would be  
the floor, roof and each sidewall. Any sharp edges left from port runner enlargement should be radius-blended to prevent high rpm  
air/fuel separation at the cylinder head. This does not include removing material on floor back into the runner from the exit end. It is  
just a port match. Hard-roll polishing is acceptable, but substantial amounts of grinding away of manifold material can impair its  
performance by substantially upsetting air/fuel distribution among cylinders.  
Note: Carburetor flange has been machined to accept a 4500 series carb and will require blending from the carb flange  
to roof of runners per your given application.  
CARBURETOR SPACERS: Carburetor spacers offer a convenient method of tuning a manifold to particular engine combinations.  
Certain cam and head packages like more plenum volume which you can get by using a one- or two-inch open spacer (Edelbrock  
#8717 or #8718). Open spacers also help a small carburetor by giving the high speed air/fuel mixture exiting the carburetor more  
length to make the turn into the runners. Four-hole spacers can be used to increase carburetor signal and/or reduce the effect of  
reversion on the carburetor. The use of a spacer normally requires slight re-calibration of the carburetor since small losses of fuel  
signal cause the engine to run somewhat leaner than without the spacer. A simple jet change is typically all that needs to be done.  
PLEASE complete and mail your warranty card. Be sure to write the model number of this product in the “Part #____” space.  
THANK YOU.  
Edelbrock Corporation  
2700 California St.  
Torrance, CA 90503  
Tech Line: 1-800-416-8628  
©2002 Edelbrock Corporation  
Brochure No. 63-0132  
Rev. 8/02  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edimax Technology Network Router 3G 6210n User Manual
Edirol Portable Speaker MA 5A User Manual
Electra Accessories Freezer EBD 8 6 User Manual
Electro Voice Microphone 637 User Manual
Electro Voice Power Supply AC24M User Manual
Fisher Paykel Convection Oven OV 250 User Manual
Fluke Work Light 742A Series User Manual
Gateway Server ALR 7300 User Manual
GE Freezer FUM5 FCM7 FCM15 FCM25 User Manual
Generac Printer 5550 User Manual