Edelbrock Automobile Parts Ford FE User Manual

FORD FE ROCKER SHAFT STUD KIT  
For Performer RPM FE Cylinder Heads  
Catalog #6009  
®
INSTALLATION INSTRUCTIONS  
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and  
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this  
installation, it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical  
Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected].  
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation  
will void your warranty and may result in poor performance and engine or vehicle damage.  
PLEASE complete and mail your warranty card. Be sure to write the model number of this product in the "Part #____" space. THANK YOU.  
DESCRIPTION: Rocker shaft stud kit P/N 6009 is designed for Ford 390-428 FE engines using Edelbrock Performer RPM FE cylinder heads  
#60057, 60058, 60059, 60069, 60079, or 60089. This stud kit will provide better rocker shaft retention, ensuring full engagement of the  
fastener in the cylinder head while eliminating the possibility of bottoming the rocker shaft bolts in the cylinder head. The use of studs will  
eliminate any wearing of the threads in the cylinder heads as the rocker shaft assemblies are drawn down into position against the valve spring  
loads with the rocker shaft fasteners.  
KIT CONTENTS:  
8 Stud, 3/8-16 x 3/8-24 x 3.62” Long  
8 Nut, 3/8-24, Flanged, 12 Point  
8 Washer, 3/8” i.d. x 7/8” o.d. x .150” thick  
1 Assembly Lube Packet  
INSTALLATION PROCEDURE  
1. Remove the valve covers and rocker shaft assemblies if they are installed.  
2. Clean any oil from the threads in the rocker shaft attachment boltholes in the cylinder heads.  
3. Apply a removable strength thread locker like Loctite blue 242 or equivalent to the cylinder head end of the studs.  
4. Install the studs hand tight in the cylinder heads checking that the studs are bottomed in the boltholes. The studs do not need to be  
tightened in the cylinder head; the thread locker should prevent the stud from backing out during disassembly.  
5. Place the rocker shaft assemblies in their positions on the studs checking that the pushrods and rocker arms are aligned properly.  
6. When installing the nuts and washers, it is recommended to use ARP assembly lubricant or equivalent on the studs, nut threads and  
washers. If ARP lubricant is not available, engine oil can be used.  
7. After lubricant is applied to the stud threads, nut threads, and washer, install the washers and nuts. The non-chamfered side of the washer  
should be installed down towards the rocker shaft stand.  
8. Tighten the nuts evenly as the rocker shaft assembly is being pulled down into position against the pressure of the valve springs.  
9. Once the rocker shaft is pulled down into place, tighten the nuts to 35 ft-lbs if using ARP assembly lubricant or 40-45 ft-lbs if using engine  
oil.  
10. Adjust the valve lash or hydraulic lifter preload and install the rocker covers. Consult service manuals for specific procedures, if necessary.  
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503  
Tech-Line: 1-800-416-8628 • E-Mail: [email protected]  
Catalog #6009  
Rev. 4/06 - RS/mc  
©2006 Edelbrock Corporation  
Brochure #63-0030  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eiki Projector LC SX6 User Manual
Euro Pro Pressure Washer VPW38H User Manual
Fire Magic Burner 25326 016 User Manual
Fisher Price Baby Accessories T8377 User Manual
FoodSaver Food Saver V240 User Manual
Foundations Baby Furniture 103 BQS User Manual
Frigidaire Washer FFTW1001PW User Manual
GE Monogram Cooktop ZGU385L User Manual
GE Refrigerator 200D8074P039 User Manual
Giant Coffeemaker p46w User Manual