PAS Articulating Hedge Clipper Attachment
Operator's Manual
MODEL
99944200590
Serial Number 001001 & Up
FOR MODELS:
SRM-2100SB/2400SB
SRM-210SB/211SB
SRM-260SB/261SB
PAS-2100/2400
PAS-210/211
PAS-230/231
PAS-260/261
PAS-2601
WARNING
DANGER
Readrulesforsafeoperationandinstructionscarefully. ECHOprovidesanOperator's
ManualandaSafetyManualforProAttachmentSeriespowersourceorSplitBoom
Trimmer. Thosemanualsandthismanualmustbereadandunderstoodforproperand
safeoperation,otherwiseseriouspersonalinjurymayresult.
X770000310
06/03
X7702273700
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
3
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key words
and what they mean to you.
This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can
lead to serious personal injury to operator and bystand-
ers.
IMPORTANT Theenclosedmessage
provides information necessary for the
protection of the unit.
NOTE This enclosed message provides
tips for use, care and maintenance of the
unit.
The circle with the slash symbol means whatever is
shown within the circle is prohibited.
SAFETY
DECALS
Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help
you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal
cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDERING instructions for specific
information.
Shaft Decal
WARNING
DANGER
This unit can be dangerous if used improperly. • Falling objects and/or blade
contact can cause serious injury to operator, helpers and bystanders. • Keep helpers
and bystanders at least 50 feet (15m) clear of operating area. • To reduce injury risk,
READ AND UNDERSTAND the operator's Manual, replacement copies are available
through your ECHO dealer. • Wear Protective clothing (head, hearing and eye
protection meeting ANSI standards) specified in the Operator's Manual. • STOP
engine before making repairs or blade adjustments. • ALWAYS use adjustment handle
when adjusting blade angle. • Keep hand away from blade.
P/N 89016012360
Download from Www.Somanuals.com. All Manuals Search And Download.
4
INTERNATIONAL SYMBOLS
Symbol
description/application
Symbol
description/application
Symbol
Symbol
description/application
Symbol form/shape
Symbol form/shape
Symbol form/shape
Symbol form/shape
description/application
Wear slip resistant
foot wear.
DO NOT allow
flames or sparks
near fuel.
Read and understand
Operator's Manual.
Fuel and oil mixture
Finger Severing
Engine choke
control.
Ignition
ON/OFF
Wear eyes, ears and
head protection
Wear hand
protection. Use
two handed.
Hot
Surface
Emergency stop
Chain lubrication
Primer bulb
DO NOT smoke
near fuel.
Safety/Alert
Carburetor adjustment
- High speed mixture
Avoid all power
lines. This unit is not
insulated against
electrical current.
Do not operate
closer than 15 M (50
ft.) from electrical
hazards.
Carburetor adjustment
- Idle speed
Carburetor adjustment
- Low speed mixture
15 M
(50 ft.)
Plan retreat path
from falling
objects.
Keep bystanders at
least 15 meters
(50 feet) away.
SAFETY INSTRUCTIONS
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING
DANGER
Hedge Clipper users risk injury to themselves and others if the unit is used improperly or safety precautions are not
followed. Proper clothing and safety gear must be worn when operating a hedge clipper.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
Hearing Protection
ECHO recommends wearing hearing protection whenever
unit is used.
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARVES,JEWELRY.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE
requirements whenever you operate the unit.
Wear sturdy work shoes with non-skid soles;
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the unit handles. Gloves also reduce the transmis-
sion of machine vibration to your hands.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
arecooler.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
5
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold
To reduce the risk of RSI/CTS, do the
following:
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended because the minimum exposure which might trigger the
ailment is unknown.
• Avoid using your wrist in a bent, extended
or twisted position. Instead try to maintain
a straight wrist position. Also, when
grasping, use your whole hand, not just
the thumb and index finger.
• Takeperiodicbreakstominimizerepetition
and rest your hands.
• Reduce the speed and force with which
you do the repetitive movement.
• Do exercises to strengthen the hand and
armmuscles.
• Immediately stop using all power equip-
ment and consult a doctor if you feel
tingling, numbness or pain in the fingers,
hands, wrists or arms. The sooner RSI/
CTS is diagnosed, the more likely perma-
nent nerve and muscle damage can be
prevented.
• Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
• Maintain good blood circulation by performing vigorous armexercises
during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury(RSI). AnextremeRSIconditionisCarpalTunnelSyndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
EQUIPMENT
WARNING
DANGER
Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combi-
nation. Read and comply with all safety instructions listed in this manual and safety manual.
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or
replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
• Never adjust blades when the engine is operating.
• Inspect hand guard for damage. Replace if damaged or missing.
• Check that the blade assembly is firmly attached and in safe operating
condition. Dull, loose or damaged blades should not be used.
• Keep exhaust area clear of flammable debris. Avoid contact during
andimmediatelyafteroperation.
NOTE
ECHO, INC. will not be responsible for the failure of cutting devices
or accessories which have not been tested and approved by ECHO
for use with this unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
SAFE OPERATION
WARNING
DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can
cause serious injury or death.
ReadtheManuals
• Provide all users of this equipment with the Operator's Manual and
Safety Manual for instructions on Safe Operation.
CleartheWorkArea
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the unit
is in use.
KeepaFirmGrip
• Hold the front and rear handles with both hands, with thumbs and
fingers tightly encircling the handles.
KeepaSolidStance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
CuttingAngleAdjustments
• Only adjust cutting blade angle with unit flat on the ground, with the
engine stop switch in the “STOP” position. Never adjust cutting
angle with unit standing upright.
AvoidContactWithGearBoxAssemblyDuringUse
• Gear box assembly becomes hot during use. Avoid contact with gear
box assembly when using unit or making cutting angle adjustments.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
7
DESCRIPTION
The ECHO product you have purchased has been factory pre-assembled for your convenience.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
CONTENTS LIST
_____ 1 - Articulating Hedge Clipper Attachment
_____ 1 - Operator's Manual
_____ 1 - Hedge Clipper Safety Manual
_____ 1 - Warranty Registration Card
_____ 1-8x10mmWrench
_____ 1-4mmHexWrench
_____ 1 - Blade Cover
3
2
8
1
4
5
9
6
7
1. GEARTENSIONRELEASELEVER- Movingleverupreleasestensionongearstopermitadjustmentofblade
cutting angle when indexing lever is pressed. The gear tension release lever MUST be placed in the down position
to remove internal gear play before operating the hedge clipper. The gear tension lever DOES NOT secure gear box
angle setting.
2. LOWERDRIVESHAFTASSEMBLY-IncludestheGearHousingassembly,FlexibleDriveCable,BladeandSafety
Decals.
3. FLEXIBLEDRIVECABLE-Cableendfitsintoupperdriveshaftcoupler. Lubricatedrivecableevery25hourswith
ECHO® LUBETM grease.
4. BLADEANGLEINDEXINGLEVER -Springloadedleverthatengageswithanotchevery15degreestosecure
cutting angle adjustment. Press lever to disengage from notch, release after new position is selected.
5. GEARHOUSINGHANDLE- Providessecurehandgripforadjustingcuttingbladeangle.
6. GREASE FITTINGS - Grease gear case every 15-20 hours of operation or on a weekly schedule.
7. CUTTING BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable
of cutting on either side of the blade.
8. BLADE COVER - Used to cover blades during transport and storage. Remove blade cover before operating unit.
9. HEDGECLIPPERSAFETYVIDEO- (Notincludedwithunit)P/N99922202800EnglishversionandP/N99922203513
Spanish version are available at a cost of $5.00 from ECHO, INC. or any authorized ECHO dealer. The video over-
views safety precautions and proper operating techniques and is supplemental to the Safety Manual. Read and
understand the Safety Manual for complete information on safe operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
SPECIFICATIONS
PAS Articulating Hedge Clipper Attachment
Shaft Length ------------------------------------------------ 1282.7mm(50.5in.)
Attachment Width ----------------------------------------- 114.30mm(4.50in.)
Height ------------------------------------------------------- 92.1mm(3.63in.)
Weight ------------------------------------------------------ 2.73kg.(6.02lb.)
GearCaseRatio -------------------------------------------- 3.5:1
Cutter -------------------------------------------------------- Double Reciprocating Blade - Double Edge
Effective Length ----------------------------------------- 411mm(16.2in.)
Pitch ------------------------------------------------------- 35mm(1.4in.)
MaximumDiameterCut
Soft Material ---------------------------------------------- 25.4mm(1in.)
Woody Material ------------------------------------------ 13mm(1/2in.)
ASSEMBLY
POWER HEAD SHAFT/LOWER SHAFT ASSEMBLY
Tools Required: None
Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.
B
1. Set Power Head/Shaft Assembly on a level surface.
D
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-
out position.
E
C
3. Carefully fit attachment drive shaft assembly into coupler (B) to
decal assembly line (C), making sure that the inner lower drive shaft
engages into the square upper drive shaft socket.
A
F
NOTE
Earlier model Power Heads may have shorter couplings. Short
couplings fit flush to decal point (E). New couplings are 4-3/4 in.
long, and fit flush to line (C).
4. Select desired blade position by aligning one of the holes (F) in
lower shaft with locator pin position.
D
C
5. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft
hole. Insure locator pin is fully engaged by twisting lower drive
shaft. Locator pin should snap flush in coupler. Full engagement
will prevent further shaft rotation.
6. Secure lower shaft assembly to coupler by tightening clamping
knob(D).
A
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
9
OPERATION
WARNING
DANGER
All over head electrical conductors and communications wires can have electricity flow with high voltages. Never
touch wires directly or indirectly when pruning, otherwise serious injury or death may result.
ADJUSTING CUTTING ANGLE
1. Place unit on a flat, clear area. Make sure stop switch is in the
“STOP” position.
B
A
2. Move gear tension release lever (A) to “up” position.
3. Grip hedge clipper shaft at gear box.
4. Grip rear handle of cutter assembly, and hold securely.
5. Depress blade indexing lever (B) to release cutter assembly.
6. Adjust cutter assembly angle to desired position, and release
indexing lever into notch.
7. Move gear tension release lever (A) to full “down” position.
IMPORTANT
DO NOT tighten gear tension release lever nut (C) to secure angle
setting of gear box. Damage to gears will result. Adjust nut ONLY
if gear tension release lever is too loose, or too tight. Tighten nut
for snug 90° movement.
C
WARNING
DANGER
Gear Case Assembly becomes HOT during use. Always grip
assembly at black rear handle when making cutting angle adjust-
ments, otherwise serious injury may result.
A
WARNING
DANGER
DO NOT stand hedge clipper on end when adjusting cutting angle,
otherwise serious injury may result.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
MAINTENANCE
Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the
ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO dealer for repairs.
SKILL LEVEL
Level1=
Level2=
Easy to do. Most required tools come with unit.
Moderate difficulty. Some specialized tools may be required.
Level 3 = Experiencerequired.Specializedtoolsarerequired.ECHOrecommends
that the unit be returned to your ECHO dealer for service.
MAINTENANCE INTERVALS
Component/System
Maintenance Procedure
SkillLevel
Frequency
Cutting Blades
Drive Shaft
Gear Housing
Screws/Nuts/Bolts
Oil/Clean
Grease
Grease
Inspect/Tighten/Replace
1
1
1
1
Before each use
Every 50 hours of use
Every 15-25 hours of use
Before each use
LUBRICATION
Blades
Level1
Tools Required: Clean rag, brush , oil can
Parts Required: 20WEngineOil(lubrication),50-50mixtureof
kerosene and 20W oil (cleaning).
WARNING
DANGER
Blades are very sharp. Wear gloves to protect hands, otherwise
serious personal injury may result.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
11
1. Brush loose debris from blade and coat both sides of blade with
the50-50cleaningmixture.
2. Allow cleaning mixture to soften the remaining gummy residue then
wipe it from the blade.
3. Apply clean oil to the entire length of the blade. Be certain the
blade bolts are lubricated.
4. Wipe excess oil from the blade before putting the unit back in
service.
Gear Housing
Level1.
Tools required: GreaseGun,Rag.
Parts required: ECHO® LUBETM 14oz.CartridgeP/N91015Greaseor
Lithium-basedGrease.
1. Clean dirt from grease fittings (A).
A
2. Carefully pump grease in each fitting. DO NOT force grease.
Too much pressure will force grease past seals and cause damage.
Apply 1-2 pumps of grease every 15-25 hours of operation.
A
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Drive Shaft (Lower)
Level1.
Tools required: 4mmhexwrench, 8mmOpenEndWrench, CleanRag,
SmallBrush.
Parts required: ECHO® LUBETM 14oz.cartridgeP/N91015or
Lithium-basedGrease.
IMPORTANT
Lower and upper drive shaft must be lubricated with ECHO®
LUBETM grease every 50 hours of operation, otherwise drive
shaft assembly overheating and failure can result.
1. Carefully remove locating screw and washers (A) to avoid loss of
blade indexing lever spring (B), and loosen clamping screw (C).
Remove the flex drive shaft assembly from the gear housing.
A
B
C
2. Pull the drive shaft (D) from the drive shaft assembly, and wipe
clean. Re-coat with a thin coating [1/2 oz. (15 ml)] of grease.
3. Slide the flex shaft back into the drive shaft assembly, being careful
not to get dirt on the flex shaft.
NOTE
Install drive shaft in gear case to provide desired blade adjustment
direction.
D
4. Align the locating screw hole in gear case with the locating hole in
drive shaft assembly, and install and tighten locating screw with
washers (A), and tighten clamping screw (C).
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
13
SHARPENING BLADES
Level3.
Tools required: Flat file, round file, screwdriver
Parts required: None
WARNING
DANGER
Hedge Clipper Blades are very sharp. Wear gloves to protect
hands.
1. Disconnect spark plug wire from spark plug.
2. Slide blades to allow file clearance using slots (A) on bottom of
blades. Do not pry against cutting edges.
A
A
3. Follow the original shape, and file each cutting edge carefully to
avoid damage to adjacent teeth. Maintain 6 mm (.25 in.) radius at
base of each tooth.
6mm (.25 in.) Radius
IMPORTANT
45º
If a power grinder is used, DO NOT allow blade to over heat.
4. Lubricate blades. See "Lubrication" on page 11.
5. Connect spark plug wire.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
BLADE ADJUSTMENT
Level2.
Tools required: (2)10mmwrenches
Parts required: None
IMPORTANT
Blades should only be removed and reinstalled by an Authorized
ECHOServicingDealer,otherwiseprematurewearorinternal
damage may occur.
1. Tighten blade bolts until snug, then loosen blade bolts 1/2 turn.
2. Hold blade bolts from turning using 10 mm wrench, and tighten
blade lock nuts with other 10 mm wrench.
NOTE
Locking ability of Hedge Clipper blade lock nuts will diminish each
time they are removed. Replace if turning resistance is not felt when
installing locknuts.
STORAGE
IMPORTANT
Always store and transport hedge clippers in a stable, horizontal
position. Support gear case and cutting blades to prevent
excessive flexing which may cause damage to the cutting
attachment. Always install blade cover when transporting or
storing unit.
1. Clean and lubricate cutting blades and gear case.
2. Sharpen cutting blades as required.
3. Apply a light coating of clean 20W engine oil along entire length of
blades and on blade bolts.
4. Install blade cover onto hedge clipper cutting blades.
5. Store hedge clipper attachment in a dry, dust free place in a
horizontal position, out of the reach of children.
Download from Www.Somanuals.com. All Manuals Search And Download.
PAS ARTICULATING HEDGE CLIPPER ATTACHMENT
OPERATOR'S MANUAL
15
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING INFORMATION
PARTS
GenuineECHOPartsandECHOREPOWER™PartsandAssembliesfor
your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model
Number and Serial Number of the unit with you. You can find these
numbers on the engine housing. For future reference, write them in the
space provided below.
Model No. _____________ SN. ____________
SERVICE
DEALER?
Call
1-800-432-ECHO
or
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call:1-800-432-ECHO(3246). Dealerinformationisalsoavailableonour
Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
ECHO CONSUMER PRODUCT SUPPORT
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
ConsumerProductSupportDepartmentat1-800-673-1558from8:30am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
WARRANTY REGISTRATION
You may register your Echo equipment using the warranty registration
direct link between you and ECHO if we find it necessary to contact
you.
ADDITIONAL OR REPLACEMENT MANUALS
Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at
Operator'sandPartsManualsareavailableby:
• Downloadingfreefromwww.echo-usa.com
• Purchasing from your Echo Dealer.
• Manuals are available by sending a written request stating the model number and serial number of your Echo unit,
part number of the manual, your name and address, and mail to the address below.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
Available Parts Catalog
PASArticulatingHedgeClipperAttachmentModel99944200590
PartNumber 99922203332
SerialNumber001001&Up
ECHO, INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047
Download from Www.Somanuals.com. All Manuals Search And Download.
|