Dynex TV Video Accessories DX WD1201 User Manual

DX-WD1201  
Tools needed  
3
No. 2 Phillips screwdriver  
Caution: Do not  
use an electric drill  
or screwdriver  
Hammer  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4
DX-WD1201  
Package contents  
Package contents: hardware  
Make sure you have all the hardware necessary to assemble your new TV stand:  
Label  
Hardware  
Qty.  
Label  
Hardware  
Qty.  
Rubber  
sleeve  
Q
4
M2  
17  
Hidden cam  
R
S
13  
1
Cam cover  
Cam dowel  
N2  
17  
Warning  
label  
Angle  
bracket  
O
P
3
6
Metal pin  
Label  
Hardware  
Qty.  
T
2
Black1-7/8”flat  
head screw  
U
V
6
Black 9/16” large  
head screw  
24  
Nail  
1
2
3
4in  
10  
20  
30  
40  
50  
60  
70  
80  
90  
100mm  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DX-WD1201  
5
Package contents: parts  
Note: All parts except for the back (G) have a lettered sticker to make identifying parts easier.  
Letter  
Description  
Right end  
Qty. Letter  
Description  
Qty.  
1
1
1
1
1
1
Back  
A
B
C
G
H
I
1
1
1
1
1
2
Left end  
Upright  
Top  
Adjustable shelf  
Stop molding  
Top skirt  
D
E
J
Bottom  
Shelf  
Bottom molding  
End molding  
K
W
F
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
DX-WD1201  
Assembly instructions  
Step1:  
Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.  
A hidden cam (M2) has an arrow. When you insert the hidden cam, make sure that the arrow points toward  
the hole in the side of the part you are inserting it into.  
Push seventeen hidden cams (M2) into the ends (A and B), top (D), bottom (E), and shelf (F). Then, insert the  
metal end of a cam dowel (N2) into each hidden cam.  
Do not tighten the hidden cams in this step.  
Arrow  
You’ll need:  
M2 (17)  
N2 (17)  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DX-WD1201  
7
Tightening hidden cams:  
In the remaining steps, use these illustrations for instructions on tightening hidden cams.  
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not  
completely tightened will loosen, and parts may separate.  
Arrow  
Make sure that you turn the  
hidden cam a minimum of  
190° to a maximum of 210°.  
Note the position of the arrow  
on the hidden cam.  
Arrow  
210°  
In the illustration below,  
the hidden cam has not  
been tightened enough.  
190°  
You’ll need:  
Phillips screwdriver  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8
DX-WD1201  
Step 2:  
Fasten the shelf (F) to the ends (A and B). Use a Phillips screwdriver to tighten four hidden cams (M2). See  
Insert two metal pins (P) into the upright (C), then insert the other ends of metal pins (P) into the holes in the  
shelf (F).  
Notched edge  
Finished edge  
Notched  
edge  
Surface with holes  
Arrow  
210°  
190°  
You’ll need:  
Phillips screwdriver  
P (2)  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-WD1201  
9
Step 3:  
Slide the bottom molding (K) onto the notched edge of the bottom (E).  
Fasten the bottom (E) to the ends (A and B). Use a Phillips screwdriver to tighten four hidden cams (M2). See  
Fasten the bottom (E) to the upright (C). Use a Phillips screwdriver and two black 1-7/8" flat head screws (T).  
Surface  
with  
hidden  
cams  
US Patent #5,499,886  
Holes for screws  
Arrow  
210°  
190°  
You’ll need:  
T (2)  
Phillips screwdriver  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
DX-WD1201  
Step 4:  
Fasten three angle brackets (O) to the stop molding (I). Use a Phillips screwdriver and three black 9/16" large  
head screws (U).  
Fasten the stop molding (I) to the top (D). Use a Phillips screwdriver to tighten three hidden cams (M2).  
Carefully turn your stand onto its top.  
Fasten the ends (A and B) to the top (D). Use a Phillips screwdriver to tighten six hidden cams (M2).  
Arrow  
210°  
190°  
Notched edges  
You’ll need:  
Phillips screwdriver  
O (3)  
U (3)  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-WD1201  
11  
Step 5:  
Slide the end moldings (W) onto the notched edges of the ends (A and B).  
Fasten the top skirt (J) to the angle brackets (O) on the stop molding (I). Use a Phillips screwdriver and three  
black 9/16" large head screws (U).  
Note: There are no pre-drilled holes in the top skirt (J). The screws will tighten into the groove.  
You’ll need:  
Phillips screwdriver  
U (3)  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
DX-WD1201  
Step 6:  
Carefully turn your stand over onto its front edges. Unfold the back (G) and lay it over your stand.  
Make equal margins along the side and bottom edges of the back (G). Push on opposite corners of your stand  
if needed to make it “square.”  
Fasten the back (G) to your stand using the nails (V).  
Note: Make sure that you tap nails into the holes that line up over the upright (C) and shelf (F).  
Note: Perforations have been provided for access through the back (G). Carefully cut out the holes needed.  
Caution: Do not  
These holes must line up over the  
back edges on the upright (C) and  
shelf (F).  
stand your stand  
upright without the  
back fastened. Your  
stand may collapse.  
Do not tap  
nails in this  
edge  
You’ll need:  
Hammer  
V (24)  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-WD1201  
13  
Step 7:  
Carefully stand your stand upright.  
Push the rubber sleeves (Q) over the remaining metal pins (P). Insert the metal pins (P) into the hole locations  
of your choice in the right end (A) and upright (C). Set the adjustable shelf (H) onto the metal pins (P).  
Apply the warning label (S) to the top (D). You should be able to read the label when the TV is removed from  
your stand. When the TV is in place, it should hide the label. Peel off the backing and apply the label as  
shown.  
Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to  
remove it. You may damage the finish on the top.  
Push a cam cover (R) onto each visible hidden cam (M2).  
Clean with your favorite furniture polish or a damp cloth. Wipe dry. Your stand is ready to use.  
Warning: Never use this furniture with a TV  
that is too large or too heavy. Severe injury  
or death can occur. The TV and furniture  
will be unstable and may tip.  
The TV must weigh less than 95 lbs.  
The base of the TV must be able to sit  
completely on this shelf.  
P and Q  
You’ll need:  
P (4)  
Q (4)  
R (13)  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
DX-WD1201  
Still need help?  
For customer service, call: 800-305-2204 (U.S./Canada markets)  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Avenue South, Richfield, MN USA 55423-3645  
© 2012 BBY Solutions, Inc.  
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other  
products and brand names are trademarks of their respective owners.  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-WD1201  
15  
This page intentionally left blank.  
Need help? Call 800-305-2204  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Certificate of Conformity  
1. This certificate applies to the Sauder  
Woodworking Product identified by this  
instruction booklet.  
2. This certificate applies to the compliance of this  
product with the CPSC Ban on Lead-Containing  
Paint (16 CFR 1303).  
3. This product was manufactured by:  
Sauder Woodworking Company  
502 Middle Street  
Archbold, Ohio 43502  
(419) 446-2711  
4. Date of Manufacture: _________________  
Lot number: 345973  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.  
© 2012 BBY Solutions, Inc.  
All rights reserved.  
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and  
brand names are trademarks of their respective owners.  
12-0782  
ENGLISH  
Download from Www.Somanuals.com. All Manuals Search And Download.  

EAW Speaker UB22z User Manual
Edelbrock Automobile Parts 17935 User Manual
Edelbrock Automobile Parts Blazer User Manual
Electra Accessories Range EL 370 User Manual
GE Air Conditioner AZ85E12EAC User Manual
Gefen TV Converter Box GTV HDMI 2 HDMIAUD User Manual
GE Fryer 681131689489 User Manual
Genz Benz Musical Instrument Amplifier BP30 User Manual
GE Pressure Washer WHRE5260 User Manual
GE Washer WWA8657R User Manual