Dynex TV Mount dx drtvm112 User Manual
ASSEMBLY GUIDE  
DX-DRTVM112  
Low-Profile TV Wall Mount  
Safety information and specifications . .2  
Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . .3  
Package contents . . . . . . . . . . . . . . . . . . . . .4  
Installation instructions. . . . . . . . . . . . . . . .5  
For either wood-stud or  
concrete wall installations  
Before using your new product, please read these instructions to prevent any damage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-DRTVM112  
3
Tools needed  
You will need the following tools to assemble your new TV wall mount:  
ardware  
Level  
Pencil  
Drill  
1/8" (3 mm) wood drill  
bit for wood stud wall  
OR  
Edge-to-edge stud  
finder  
3/8" (10 mm) masonry  
drill bit (concrete only)  
Socket wrench with 7/16"  
(12 mm) socket or  
adjustable wrench  
Phillips screwdriver  
Hammer  
Adjustable wrench  
Tape  
Measuring tape  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4
Package contents  
Make sure that you have all of the hardware necessary to assemble your new TV wall mount:  
A TV Bracket (1)  
B Wall Plate (1)  
C Bracket Extensions (2)  
D Wall mount template (1)  
DX-TVM111  
A
C
B
D
Template • Gabarit • Plantilla  
Top  
Haut  
Parte superior  
Tools Needed  
Outils nécessaires  
Herramientas requeridas  
Note  
Remarque  
localiser d'abord les montants en bois,  
détecteur de montants.  
:
Pour une construction  
à
ossature de bois,  
l'aide d'un  
à
Nota: para la instalación en construcciones de armazón de  
madera, primero debe localizar las vigas de madera con un  
localizador de vigas.  
Need more information about your mount? Scan  
this QR code or visit www.dynexproducts.com.  
<FR>Need more information about your mount?  
Scan this QR code or visit www.dynexproducts.com.  
<SP>Need more information about your mount?  
Scan this QR code or visit www.dynexproducts.com.  
http://san.us/284  
V1 13-0138  
TV Hardware Bag  
Label  
E
Hardware  
Qty.  
4
Label  
I
Hardware  
Qty.  
2
M4 × 12 mm  
screw  
1/4" × 2 3/4" lag bolt  
Concrete anchor  
M4 × 35 mm  
screw  
F
4
4
J
K
L
2
4
4
M4 washer  
G
M6 x 14 mm screw  
M4 spacers  
H
4
M6 Nut  
1
2
3
4in  
10  
20  
30  
40  
50  
60  
70  
80  
90  
100mm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
DX-DRTVM112  
5
Installation instructions  
STEP 1 - Determining the hole pattern on your TV  
1
Carefully place your TV screen face down on a cushioned, clean surface to protect the screen from  
damage and scratches.  
2
If your TV has a table top stand attached, remove the stand. See the documentation that came with your  
TV for instructions.  
3
4
Measure the distance between the mounting holes on the back of your TV.  
If your TV has a 200 x 200 mm hole pattern, you must install the bracket extensions (C) onto the TV  
bracket (A).  
200 mm  
100 mm  
75 mm  
200 mm  
75 mm  
100 mm  
C
A
L
K
5
If you need to install the extension brackets (C), install them on the front (flat side) of the TV bracket (A)  
with four M6 x 14 mm screws (K) and four M6 nuts (L), as shown, using the phillips screwdriver and the  
adjustable wrench.  
You’ll need  
Nuts  
Screws  
Phillips screwdriver  
K (4)  
L (4)  
C (2)  
TV bracket (A)  
Adjustable wrench  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6
STEP 2 - Determine whether your TV has a flat, irregular, or  
obstructed back  
1
2
3
Temporarily lay the TV bracket (A) and adapters (C), if necessary, on the back of your TV.  
Align the screw holes in the TV bracket with the mounting screw holes on your TV.  
Identify which type of back your TV may have:  
Flat back: The bracket and adapters (if necessary) lay flush against the back of your TV and does not  
block any jacks. You do not need spacers when assembling the wall mount.  
•
•
•
Obstructed back: The bracket and adapters (if necessary) block one or more of the jacks on the back of  
your TV. You will need spacers when assembling the wall mount.  
Irregularly-shaped back: There is a gap between the bracket and adapters (if necessary) and some  
part of the back of your TV. You will need spacers when assembling the wall mount.  
4
Remove the TV bracket (A) and adapters (C).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-DRTVM112  
7
STEP 3 - Select screws and spacers  
1
Select the hardware for your TV (screws and spacers). A limited number of TVs come with mounting  
hardware included. (If there are screws that came with the TV, they are almost always in the holes on the  
back of the TV.)  
Select one of the following types of screws:  
M4 × 12 mm screws (E) for a flat back TV.  
M4 × 35 mm screws (F) for an irregular or obstructed TV back.  
For an irregular or obstructed TV back, use the following spacers:  
M4 spacers (H)  
CAUTION:To avoid potential personal  
injuries and property damage, make sure that there  
are adequate threads to secure the brackets to your  
Screw fits  
correctly  
TV. If you encounter resistance, stop immediately and  
contact customer service. Use the shortest screw and  
spacer combination to accommodate your TV. Using  
hardware that is too long may damage your TV.  
However, using a screw that is too short may cause  
your TV to fall from the mount.  
Screw is too  
long  
Screw is too  
short  
2
3
Remove the screws.  
For a flat back TV, go to “STEP 4 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on  
page 8.  
-OR-  
For an irregular or obstructed back, go to “STEP 4 - Option 2: Attaching the mounting hardware to TVs  
with irregular or obstructed backs” on page 9.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
STEP 4 - Option 1: Attaching the mounting hardware to TVs  
with a flat back  
1
2
3
Align the TV bracket (A) with the screw holes on the back of the TV.  
Install washers (G ), and screws (E) into the holes in the back of the TV.  
Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
G
E
You’ll need  
Washers  
Screws  
Phillips screwdriver  
E (4)  
G (4)  
TV bracket (A)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-DRTVM112  
9
STEP 4 - Option 2: Attaching the mounting hardware to TVs  
with irregular or obstructed backs  
1
2
Align the TV bracket (A) with the screw holes on the back of the TV.  
Place spacers (H) behind the TV bracket and the washers (G) over the holes in the TV bracket, then insert  
the screws (F) through the washers, TV bracket, and spacers.  
3
Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
A
H
G
F
You’ll need  
Washers  
Screws  
Spacers  
Phillips screwdriver  
F (4)  
H (4)  
G (4)  
TV bracket (A)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
10  
STEP 5 - Determine wall-mount location  
Notes:  
•
•
For more detailed information on determining where to drill your holes, visit our online height-finder at:  
http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder  
Your TV should be high enough so your eyes are level with the middle of the screen. Normally, the center  
of your TV should be 40 to 60 inches (100 to 150 cm) above the floor.  
The center of your TV will match the center of the wall plate (B). Before you drill holes in the wall:  
1
2
Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is  
measurement a.  
Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall.  
Keep in mind that the bottom of the TV should be placed above any furniture (such as entertainment  
centers or TV stands). The TV should also be above items placed on top of the furniture (like a Blu-ray  
player or cable box). This measurement is b.  
3
4
Add a + b. The total measurement is the height where you want the center of the wall plate (B) to be on  
the wall.  
Use a pencil to mark this spot on the wall.  
a
b
You’ll need  
Measuring tape  
Pencil  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-DRTVM112  
11  
STEP 6 - Option 1: Installing on a wood stud* wall  
Note: Any drywall covering the wall must not exceed 5/8" (16 mm).  
1
2
Locate the stud. Verify the center of the stud with an edge-to-edge stud finder.  
Align the wall plate template (D) at the height you determined in the previous step and make sure that it  
is level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).  
Drill pilot holes to a depth of 3 in. (75 mm) using a 1/8" (3 mm) wood drill bit. Remove the wall plate  
template.  
Align the wall plate (B) with the pilot holes, insert the lag bolts (I) through the holes in the wall plate,  
then tighten the lag bolts only until they are firm against the arm assembly.  
3
4
CAUTION:Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (I).  
* Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal  
11/2 x 31/2 in. (38 x 89 mm).  
D
B
3 in.  
(75 mm)  
I
You’ll need  
DX-TVM111  
Template Gabarit  
•
•
Plantilla  
Top  
Haut  
Parte superior  
Tools Needed  
Outils nécessaires  
Herramientas requeridas  
Note  
Remarque  
localiser d'abord les montants en bois,  
détecteur de montants.  
:
Pour une construction  
à
ossature de bois,  
l'aide d'un  
à
Nota: para la instalación en construcciones de armazón de  
madera, primero debe localizar las vigas de madera con un  
localizador de vigas.  
Need more information about your mount? Scan  
this QR code or visit www.dynexproducts.com.  
<FR>Need more information about your mount?  
Scan this QR code or visit www.dynexproducts.com.  
<SP>Need more information about your mount?  
Scan this QR code or visit www.dynexproducts.com.  
1/8" wood 7/16" (12mm)  
Tape  
Level  
Pencil  
http://san.us/284  
V1 13-0138  
drill bit  
socket wrench  
Edge-to edge  
stud finder  
Drill  
Wall plate  
(B)  
Template (D)  
I (2)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
STEP 6 - Option 2: Installing on a solid concrete* or concrete  
block wall  
CAUTION:To prevent property damage or personal injury, never drill into mortar between  
blocks. Mount the wall plate directly onto the concrete surface.  
1
2
3
4
Align the wall plate template (D) at the height you determined in the previous step and make sure that it  
is level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).  
Drill pilot holes to a depth of 3 in. (75 mm) using a 3/8 in. (10 mm) diameter masonry drill bit. Remove  
the wall plate template.  
Insert the concrete wall anchors (J) into the pilot holes and use a hammer to make sure the anchors are  
flush with the concrete surface.  
Align the wall plate (B) with the anchors, insert the lag bolts (I) through the holes in the wall plate, then  
tighten the lag bolts only until they are firm against the wall plate.  
CAUTION:Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (I).  
* Minimum solid concrete thickness: 8 in. (203 mm)  
* Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)  
3 in.  
(75 mm)  
D
J
B
I
You’ll need  
DX-TVM111  
Template Gabarit  
•
•
Plantilla  
Top  
Haut  
Parte superior  
olede
Outils nécessaires  
Herramientas requeridas  
Note  
Remarque  
localiser d'abord les montants en bois,  
détecteur de montants.  
:
Pour une construction  
à
ossature de bois,  
l'aide d'un  
à
Nota: para la instalación en construcciones de armazón de  
madera, primero debe localizar las vigas de madera con un  
localizador de vigas.  
3/8" masonry  
drill bit  
Need more information about your mount? Scan  
this QR code or visit www.dynexproducts.com.  
<FR>Need more information about your mount?  
Scan this QR code or visit www.dynexproducts.com.  
<SP>Need more information about your mount?  
Scan this QR code or visit www.dynexproducts.com.  
Pencil  
7/16" (12 mm)  
Tape  
http://san.us/284  
V1 13-0138  
Drill  
socket wrench  
Wall plate (B)  
Template (D)  
I (2)  
J (2)  
Hammer  
Level  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DX-DRTVM112  
13  
STEP 7 - Mounting the TV to the wall plate  
1
Place the TV bracket (A) into the slotted flanges of the wall plate (B). The TV can be mounted either (1)  
vertically, or (2) with a 6° tilt.  
2
Lock the TV and bracket assembly to the wall plate by rotating the lock into the flange slot.  
HEAVY! You will need assistance  
with this step.  
For a vertical mount, attach the TV bracket to the flange that is closest to the wall plate.  
A
B
B
A
For a tilt mount attach the TV bracket to the flange that is farthest from the wall plate.  
B
A
B
A
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
STEP 8 - Removing the TV from the wall plate and  
disassembling the wall mount  
1
2
Unlock the TV and bracket assembly from the wall plate by rotating the lock out of the flange slot.  
Lift the TV bracket (A) from the slotted flanges of the wall plate (B) and place it on a cushioned, clean  
surface to protect the screen from damage and scratches.  
3
4
Using a Phillips screwdriver, remove the screws from the back of your TV, then remove the TV bracket.  
Using a 7/16” or 12 mm socket wrench, remove the lag bolts from the wall, then remove the wall plate.  
HEAVY! You will need assistance  
with this step.  
A
B
B
A
G
E
You’ll need  
7/16" (12 mm)  
socket wrench  
Phillips screwdriver  
Download from Www.Somanuals.com. All Manuals Search And Download.  
www.dynexproducts.com 1-800-305-2204 (U.S. and Canada) or 01-800-926-3020 (Mexico)  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.  
© 2013 BBY Solutions, Inc. All rights reserved.  
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and  
brand names are trademarks of their respective owners.  
6907-00205100  
V1 ENGLISH 13-0668  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Chainsaw CS 330T CS 360T User Manual
Eiki CRT Television LC XB29N User Manual
Electro Voice Home Theater System PA1250T User Manual
Fisher Price High Chair P9043 User Manual
Friedrich Air Conditioner CP05C10 User Manual
FUNAI DVD Recorder ZC350MS8 User Manual
GE Monogram Range ZDP484LGPSS User Manual
Genie Work Light 1000 1200 User Manual
GE Universal Remote 24958 User Manual
Global Machinery Company Blower PB26CC User Manual